NEC E321, E421, E461, S401, S461 Installation And Assembly Manual

PDF

Document

NEC DISPLAY SOLUTIONS OF AMERICA, INC.

Installation and Assembly - Flat Screen Wall

Mount for NEC models:

ASPV32, ASPV40, E321, E421, E461,

LCD3210, LCD3215, LCD4020, LCD4215,

LCD4615, LCD4620, LCD5220, LCD5710,

M40, M46, P401, P461, P521, P551, S401,

S461, S521, SC40, SC46, V321, V421, V461,

X461HB, X461UN

Model: WMK3257

This product is intended for use with UL

Listed products and must be installed by a qualified professional installer.

Maximum UL Load Capacity: 150 Ib (68 Kg)

ISSUED: 03-26-10 SHEET #: 125-9106-3 08-04-10

Note: Read entire instruction sheet before you start installation and assembly.

WARNING

• Do not begin to install this product until you have read and understood the instructions and warnings contained in this

Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call customer care at 1-800-865-2112.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building construction, and fully understands these instructions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.

• Never exceed the UL Listed Maximum Load Capacity of 150 lb (68 kg).

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an

"edge to edge" stud finder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding power.

• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury.

• This product was designed and intended to be mounted to the following supporting surfaces checked below with the hardware included in this product as specified in the installation sheet. To mount this product to an alternative supporting surface, contact customer care at 1 800 865-2112.

• This product was designed to be installed on the following wall construction only;

WALL CONSTRUCTION x Wood Stud x Wood Beam x Solid Concrete x Cinder Block

Metal Stud

Brick

Other or unsure?

ADDITIONAL HARDWARE REQUIRED

None

Do not attach except with Peerless accessory kit for metal studs;

Contact Customer Service for Peerless accessory kit for metal studs.

(not evaluated by UL)

Contact Customer Service (not evaluated by UL)

Contact Customer Service

Parts List .............................................................................................................................................................................. 3

Installation to Double Wood Stud Wall .................................................................................................................................. 4

Installation to Solid Concrete or Cinder Block ....................................................................................................................... 5

Installing Tilt Brackets ........................................................................................................................................................... 6

Installing Flat Panel Screen to Wall Plate ............................................................................................................................. 7

For customer care call (800) 865-2112 or (708) 865-8870.

2 of 7 ISSUED: 03-26-10 SHEET #: 125-9106-3 08-04-10

Tools Needed for Assembly

• stud finder ("edge to edge" stud finder is recommended)

• phillips screwdriver

• drill

• 1/4" bit for concrete and cinder block wall

• 5/32" bit for wood stud wall

• level

Accessories

• 4 piece Metal Stud Fastener Kit (ACC 415) (Not UL listed)

Before you begin, make sure all parts shown are included with your product.

Parts may appear slightly different than illustrated.

PARTS LIST

E l

D w r

# c i e e a f g

1 o t s h

4 n ll t t c c p x li r t t r l e li i a t

2 t p b

t r e e b a

5 it r o c a a w n k n c e o c k t o e h d o t r s c r e w

6" - 4 mm security allen wrench

M m

M k k k e e e

K M5 x 6 mm socket pin serrated washer head screws e

1 x

6 u

8 t

" l e t x x x

i n

2 w

1 s

4 i

0 a

5 o s m m m n h m m m m e m b r r s s s s a c e o o o c c c c k e t s u r i t y t t t p p p a i i i ll n n n e s s s n c c c r r r w e e e r w w w e n c h

Q t y .

2 a

0 r

0 -

1 -

t #

1 7

0 -

1 560-9646

4 5 2 0 1 0 5 0

C 0 3

4 5 2 0 1 0 6 8

8 510-1114

2 0 1 1 7 1 1

5 6 0 1 1 4 5

B C D E G H

3 of 7

ISSUED: 03-26-10 SHEET #: 125-9106-3 08-04-10

Installation to Double Wood Stud Wall

WARNING

• Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.

• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is highly recommended.

• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Installers are responsible to provide hardware for other types of mounting situations (not evaluated by UL).

Wall plate (A) can be mounted to two studs that are 16" apart. Use a stud finder to locate the edges of the studs.

Use of an edge-to-edge stud finder is highly recommended. Based on their edges, draw a vertical line down each stud’s center. Place wall plate on wall as a template. Level plate, and mark the center of the four mounting holes.

Make sure that the mounting holes are on the stud centerlines. Drill four 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Make sure that the wall plate is level, secure it using four #14 x 2.5" wood screws (D) as shown in figure 1.2.

Skip to step 2 on page 6.

STUD

fig. 1.1

4 of 7 ISSUED: 03-26-10 SHEET #: 125-9106-3 08-04-10

Installation to Solid Concrete or Cinder Block

WARNING

• When installing this wall mount on cinder block, verify that you have a minimum of 1-3/8" of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.

1 Make sure that wall plate (A) is level, use it as a template to mark four mounting holes. Drill four 5/16"

(8 mm) dia. holes to a minimum depth of 2.5" (64 mm). Insert anchors (E) in holes flush with wall as shown (right). Place wall plate over anchors and secure with #14 x 2.5" screws (D). Level, then tighten all fasteners.

WARNING

• Tighten screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

E concrete surface

Drill holes and insert anchors (

D E

Place plate ( A ) over anchors ( E ) and secure with screws ( D ).

WARNING

• Always attach concrete anchors directly to loadbearing concrete.

• Never attach concrete anchors to concrete covered with plaster, drywall, or other finishing material. If mounting to concrete surfaces covered with a finishing surface is unavoidable (not evaluated by UL), the finishing surface must be counterbored as shown below. Be sure concrete anchors do not pull away from concrete when tightening screws. If plaster/ drywall is thicker than 5/8", custom fasteners must be supplied by installer. (not evaluated by UL)

Tighten all fasteners.

E solid concrete cinder block wall plate

INCORRECT concrete wall plate

CORRECT concrete plaster/ dry wall plaster/ dry wall

5 of 7 ISSUED: 03-26-10 SHEET #: 125-9106-3 08-04-10

Use Chart to Determine

Orientation

and Screws

LANDSCAPE

Recommended Hole Pattern

200 mm X 200 mm

300 mm X 300 mm

400 mm X 400 mm

400 mm x 200 mm

PORTRAIT

Recommended Hole Pattern

200 mm X 200 mm

300 mm X 300 mm

400 mm X 400 mm

200 mm x 400 mm

Screen

ASPV32

ASPV40

E321

E421

E461

LCD3210

LCD3215

LCD4020

LCD4215

LCD4615

LCD4620

C LCD5220

LCD5710

M40

M46

Screw Size

M6 x 12

M6 x 20

M6 x 12

M8 x 15

M6 x 12

Screen

P401

P461

P521

P551

S401

S461

S521

SC40

SC46

V321

V421

D V461 M6 x 12

X461HB M6 x 12

X461UN M6 x 12

Screw Size

M6 x 12

Screen Screw Size

ASPV32 M6 x 12

ASPV40 M6 x 12

E321

E421

E461

M6 x 12

LCD3210 M6 x 12

LCD3215 M6 x 12

LCD4020 M6 x 12

LCD4215 M6 x 12

LCD4615 M6 x 12

LCD4620 M6 x 12

C LCD5220 M6 x 12

LCD5710 M8 x 15

M40

M46

M6 x x

Screen

P401

P461

P521

P551

S401

S461

S521

SC40

SC46

V321

V421

D V461

X461HB

X461UN

Installing Tilt Brackets

MAX Distance 400 mm

fig 2.2

400 mm

300 mm

200 mm

USE TILT BRACKET ONLY

WHEN MOUNTING TO

SCREEN USING 200 X 200

HANDLES

FACE OUT

Screw Size

M6 x 12

Secure extension brackets (L) to left tilt bracket (B) with four M5 x 6 mm socket pin serrated washer head screws (K).

Height of tilt brackets may be adjusted using holes above and below center mounting location holes.

NOTE: Repeat using right tilt bracket (C).

fig 2.1

CENTER

MOUNTING

LOCATIONS

WARNING

• Tighten screws so adapter brackets are firmly attached. Do not tighten with excessive force.

Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become detached. Tighten to

40 in. • lb (4.5 N.M.) maximum torque.

• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly secured, damage may occur to screen or product may fail.

2 To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen. Place screen face side down. If screen has knobs on the back, remove them to allow the tilt brackets to be attached. Place tilt brackets (B and C) on back of screen as shown in fig. 2.2. Note: Be sure to attach tilt brackets with handles facing outward as in figure 2.2. Align tilt brackets to screen mounting holes as recommended by chart below. Attach the tilt brackets to the back of the screen using the appropriate combination of screws, either M6 x 12 mm socket pin screw

(G), M6 x 20 socket pin screw (H) or M8 x 15 mm socket pin screw (J) and multi-washers (I) as shown in figures 2.3

and 2.4. Verify that all holes are properly aligned, and then tighten screws using security allen wrench (F).

G, H or J

Landscape

Portrait

B * Use multi-washers (I) to attach tilt brackets (B and C) to your screen when using M6 x 12 mm socket pin screw (G), M6 x 20 socket pin screws (H).

USING TILT BRACKETS ONLY

M8 screws do not require multi-washers (I)

G, H

fig 2.3

or J

6 of 7

fig 2.4

USING EXTENTION BRACKETS

ISSUED: 03-26-10 SHEET #: 125-9106-3 08-04-10

Mounting and Removing Flat Panel Screen

WARNING

• Always use an assistant or mechanical lifting equipment to safely lift and position the flat panel screen.

• Do not tighten screws with excessive force. Overtightening can cause damage to mount. Tighten screws to 40 in. • lb

(4.5 N.M.) maximum torque.

• Be careful not to pinch fingers when pushing screen from the bottom.

RATCHET

HANDLE

Tension Adjustment of Ratchet Handle: Adjust tension in tilt brackets (B & C) by rotating ratchet handle. NOTE: If obstruction prevents ratchet handle from rotating, pull handle out while turning will allow handle to reposition without tightening. Release and turn handle to tighten or loosen.

Mounting Screen: Ratchet handle must be in the up or down position or interference will occur while hooking tilt brackets to wall plate (A). Slowly hook tilt brackets (B

& C) onto wall plate (A) and swing screen down as shown in fig. 3.1. Tilt bracket hooks must fully engage wall plate. Using phillips screw driver or security allen wrench (F), turn safety/security screws on tilt brackets

(B & C) clockwise till screw tip securely contacts wall plate as shown in cross section.

SAFETY/

SECURITY

SCREW

CROSS SECTION

Screen Adjustment: Screen can be adjusted horizontally by loosening safety/security screws on tilt brackets (B & C) three full turns. Adjust screen as shown in figure 3.2. Tighten safety/security screws on tilt brackets till screw tip securely contacts wall plate as shown in cross section.

Removing Screen: To remove screen from mount, loosen safety screws, swing screen away from mount, and lift screen off of mount.

fig 3.2

fig 3.1

Adjusting the Tilt Angle of the Flat

Panel Screen

4 For preset tilt angles use Increlok ™ and for custom tilt angle use ratchet handle.

INCRELOK ™ : The screen can be locked into a pre-set tilt position of -5 ° , 0 ° , 5 ° , 10 ° or 15 ° . Use locator hole to find tilt position hole and tilt screen to align holes. Tighten IncreLok™ tilt locking screws on both tilt brackets to lock tilt as shown in detail 2.

IncreLok™

TILT LOCKING

SCREW

LOCATOR

HOLE

Ratchet Handle: Loosen ratchet handle (refer to step

3 for tension adjustment of handle). Push or pull from top or bottom of screen to adjust tilt as shown in figure

4.1. The tilt can be adjusted to a maximum of 15° forward or 5° backward.

RATCHET

HANDLE

DETAIL 2 fig 4.1

7 of 7 ISSUED: 03-26-10 SHEET #: 125-9106-3 08-04-10

Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.

All other brand and product names are trademarks or registered trademarks of their respective owners.

Hello! I am an AI chatbot specifically trained to assist you with the NEC E321 Installation manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!