Gason Eureka Jindara Spectre Installation Instructions Manual

),1,6+

'21276&$/( $

Jewel / Spectre Through Wall Kit

(Part No. 233885)

Installation Instructions

),1,6+

Read and follow these instructions (in conjunction with the Jewel / Spectre

Freestanding manual) carefully before installing this appliance.

SAVE THESE INSTRUCTIONS

• The installation of this appliance must be carried out as per the manual and the flue manufactuer’s specifications

We recommend that you use a qualified installer to carry out the installation.

• Default clearance values and flue requirements specified in AS/NZS 2918-2001 must be used for any clearance values not

given in these instructions.

• If in doubt, do not hesitate to contact your local Jindara or Eureka dealer.

• This appliance weighs in excess of 230 kilograms. Extreme care should be taken when handling the appliance.

Hole cutting dimensions & clearances to combustibles

• This thru-wall kit is designed for use with plasterboard stud walls,

with a total thickness ranging between 90mm and 110mm.

• Note that the wall section below the appliance fascia on the insert

side is filled, as per figure 1. It should be supported by a stud with a

10mm x 35mm horizontal cut-out, as per figure 2. This is to allow

the base of the freestanding unit to protrude far enough through

the wall.

• A minimum 1590mm x 940mm floor protector with a minimum

thickness of 6mm must be installed under the appliance, as per

figure 3.

• The floor protector must extend a minimum of 420mm from each

appliance door and 155mm from the pedestal base on either side

of the appliance.

Note 1: If present, a combustible mantle shelf must be positioned

a minimum of 500mm above the apliance hot air outlet.

Note 2: Combustible internal wall framing must not be installed

less than 475mm above the appliance top plate.

Note 3: Non-combustible internal wall framing must be used if

installed directly above the appliance, less than 475mm

from the top plate.

Figure 2

Freestanding side

Horizontal lower support stud

110 mm

45 mm Insert side

Floor protection minimum thickness

6 mm

Figure 1

15 mm

35 mm

'21276&$/( $

Figure 3

420mm

Internal wall

420mm

See

Notes 1 & 2

See

Note 3

372mm

940mm

714mm 860 mm

5(9 %< (&11R '$7(

5(/($6('

5(9 %< (&11R '$7(

1590mm

890 mm

!

0$7(5,$/0DWHULDOQRWVSHFLILHG!

$33'

kit. For the through wall installation additional

8˝ stainless is to be over the 7˝ stainless active

then a 9˝ mesh shield and a 10˝ stainless steel

$)*$62137</7',1&,19,&725,$

5(*,67(5('2)),&(

%/$.(675((7$5$5$7

9,&725,$

7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(

3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:

'5$:1

Minimum requirements

This Heater has been tested to AS2918:2001 Appendix B.

(See diagram opposite)

6&$/(

6+((7

2)

7,7/( using an Australian Standard

5(9 %< (&11R '$7(

5(/($6('

67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(

F:\Docs\Manuals\Heaters\Heaters\GPN 234969 Jewel Spectre Thru Wall

',0(16,2166+2:17+86RU “ “

'5,//('+2/(6381&+('+2/(6“$1*/(6“ƒ

5(9 %< (&11R '$7( $33'

These must be used to make the installation conform.

120mm min.

NB: First height 4600 mm (+/– 300mm) from

)25/$6(5&87&20321(176

6+((7

2)

-,*

7˝ stainless

8˝ stainless

9˝ solid back mesh

protector

0$66NJ

)256+((7PP$1'81'(572/(5$1&(

)256+((7WRPP72/(5$1&(

$)*$62137</7',1&,19,&725,$

%/$.(675((7$5$5$7

67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(

)256+((7WRPP72/(5$1&(

9,&725,$

7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(

3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:

'5$:1

6&$/( 7,7/(

'5,//('+2/(6381&+('+2/(6“$1*/(6“ƒ

)25/$6(5&87&20321(176

)256+((7PP$1'81'(572/(5$1&(

0$66NJ

3$571R

7+,5'

352-(&7,21

3$571R

$1*/(

352-(&7,21

Parts

5

6

3

4

7

Ref. Description Qty.

1

2

Fill Panel Mount

Fill Panel

Tek Screw 10-16 x 16mm

Washer Flat 8 x 20

Insert Fascia Panel

Inner Heat Shield A

2

1

8

9

Outer Heat Shield A

Inner Heat Shield B

Outer Heat Shield B

1

1

6

4

1

1

1

12

13

14

15

16

Ref. Description Qty.

10

11

Side Fill Panel R/H

Side Fill Panel L/H

Retaining Spring

Front Heat Shield Panel

F/S Fascia Panel

Rear Heat Shield Panel

1

1

17

18

Side Fill Mount Bracket

S/Tap Screw 1/2” x 10

Set Screw M6 x 20

1

1

4

1

4

32

4

25

26

27

20

21

22

23

24

Ref. Description Qty.

19 4

Cap Screw M8 x 20

Washer Flat M6

Switch Knob

Switch - 2 Position

Switch - 3 Position

Blanking Panel

Nut Whiz Lock M6

Paint - Metallic Black

1

2

1

1

1

4

8

1

),1,6+

Figure 4

'21276&$/( $

Step 1

• Ensure that the power lead of the appliance is disconnected.

5(/($6(' (1*35

5(9 %< (&11R '$7(

• Note that if fan controls are intended to be installed on the thru-wall face if the installation, the door at the end of the appliance with fan

controls in the pedestal base should be selected for this step. Refer to figure 5.

,7(0 3$571R '(6&5,37,21

'HIDXOW

47<

6,=(

%5$&.(77+58:$//.,7

3$1(/,1),//)$6&,$

6&5(:7(.[6(/)7

:$6+(5)/$766[[

)$6&,$7+58:$//

+($76+,(/'7+528*+:$//

+($76+,(/'7+528*+:$//

+($76+,(/'7+528*+:$//

+($76+,(/'7+528*+:$//

),//3$1(/5+

),//3$1(//+

635,1*(;7PP[PP

&20%867,%/(:$//3$1(/

)5217

)$6&,$3$1(/-(:(/63(&75(

&20%867,%/(:$//),//3$1(/

)6

,1),//02817%5$&.(7

6&5(:67$3[*3+

6&5(:6(70[[3+7+(;

=3

1871</2&0

6&5(:&$30[%87+'

:$6+(5)/$70;=3

.12%32:(56:,7&+

6:,7&+326,7,2163'721

21

)$16:,7&+63(('527$5<

%/$1.,1*3$1(/,1%

187:+,=/2&.)/$1*(066

3$,17&$10(7%/$&.

-,*

$

$

%

$

$

$

$

$

0$7(5,$/

$)*$62137</7',1&,19,&725,$

5(*,67(5('2)),&(

67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(

',0(16,2166+2:17+86RU “ “

'5,//('+2/(6381&+('+2/(6“$1*/(6“ƒ

%/$.(675((7$5$5$7

9,&725,$

7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(

3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:

'5$:1

$33'

77

77

6&$/(

6+((7

2)

7,7/(

)25/$6(5&87&20321(176

)256+((7PP$1'81'(572/(5$1&(

)256+((7WRPP72/(5$1&(

)256+((7WRPP72/(5$1&(

7+58:$//.,7&20%867,%/(:$//

-(:(/63(&75()6

3$571R

0$66NJ

7+,5'

$1*/(

352-(&7,21

$

$

$

$

$

$

$

),1,6+

),1,6+

Step 2

• Remove the pedestal fill panel from the base of the appliance, at the

end being installed through the wall.

• Disconnect fan harness connectors from the switches housed in the

fill panel and secure the earth wire eyelets to the pedestal base, at

the point shown in figure 5.

),1,6+1$785$/

),1,6+1$785$/

' ),1,6+

'

Step 3

wraping is removed from the stainless steel before assembly. Note that inner

and outer heat shield A components attach to heat shield front panel, inner and

outer heat shield B components are attached to A components using screws, with

slots used for adjustment of overall depth.

• Ensure all retaining screws are securely fastened and that the depth of the heat

shields is uniformly adjusted.

• Depth of the heat shields (x ) is determined using the following calculation:

x = wall thickness - 5mm

Figure 5

'21276&$/( $

'(7$,/'

6&$/(

'21276&$/(

$

'(7$,/'

6&$/(

Attach earth points firmly using screw '21276&$/( $

Outer Heat

Shield A

Heat Shield

Front Panel

Outer Heat

Shield B

Figure 6 x

$

Inner Heat

Shield A

0$7(5,$/ -,*

5(9 %< (&11R '$7(

Inner Heat

Shield B

5(/($6('

5(9 %< (&11R '$7(

5(*,67(5('2)),&(

%/$.(675((7$5$5$7

'5$:1

5(9 %< (&11R '$7(

$)*$62137</7',1&,19,&725,$

9,&725,$

7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(

$33'

67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(

',0(16,2166+2:17+86RU “ “

'5,//('+2/(6381&+('+2/(6“$1*/(6“ƒ

)25/$6(5&87&20321(176

)256+((7PP$1'81'(572/(5$1&( 0$7(5,$/

)256+((7WRPP72/(5$1&(

0$66NJ

7+,5'

352-(&7,21

-,*

77

5(/($6('

6&$/(

6+((7

2)

%$6(+($7(5

'225+($7(5)6

3$571R

%/$.(675((7$5$5$7

9,&725,$

5(9 %< (&11R '$7(

7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(

3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:

'5$:1 77

6&$/( 7,7/(

$33'

6+((7

2)

67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(

',0(16,2166+2:17+86RU “ “

'5,//('+2/(6381&+('+2/(6“$1*/(6“ƒ

)25/$6(5&87&20321(176

)256+((7PP$1'81'(572/(5$1&(

)256+((7WRPP72/(5$1&(

)256+((7WRPP72/(5$1&(

%$6(+($7(5

'225+($7(5)6

3$571R

0$66NJ

7+,5'

$1*/(

352-(&7,21

6(&7,21$$ $

$

'21276&$/(

'21276&$/(

$

$

Step 4

• Install the front heatshield assembly to the far side of the installation,

as shown in figure 7.

• Measuring vertically from the surface that the heater is sitting on, the bottom edge

of the heatshield assembly should be raised by 77mm.

• Secure mounting brackets in place using wood screws, attaching to the vertical

stud on both sides of the cut-out.

(Through wall side)

Figure 7

'21276&$/( $

Secure to vertical stud through brackets

5(9 %< (&11R '$7(

0$7(5,$/ -,*

$)*$62137</7',1&,19,&725,$

5(*,67(5('2)),&(

%/$.(675((7$5$5$7

9,&725,$

6(&7,21$$

67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(

',0(16,2166+2:17+86RU “ “

'5,//('+2/(6381&+('+2/(6“$1*/(6“ƒ

)25/$6(5&87&20321(176

)256+((7PP$1'81'(572/(5$1&(

)256+((7WRPP72/(5$1&(

0$66NJ

7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(

3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:

'5$:1

$33'

77

77

6&$/(

6+((7

2)

7,7/(

)256+((7WRPP72/(5$1&(

7+58:$//.,7&20%867,%/(:$//

-(:(/63(&75()6

3$571R

7+,5'

$1*/(

352-(&7,21

77mm - bottom edge of fascia to top face of floor protector.

$

Figure 8

Step 5

• Install the rear heatshield panel, securing in place with 4x retaining springs,

as shown in figure 8.

(Freestanding side)

5(9 %< (&11R '$7(

0$7(5,$/ -,*

5(/($6(' (1*35

5(9 %< (&11R '$7(

$)*$62137</7',1&,19,&725,$

5(*,67(5('2)),&(

%/$.(675((7$5$5$7

9,&725,$

7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(

3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:

'5$:1

$33'

77

77

6&$/(

6+((7

2)

7,7/(

67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(

',0(16,2166+2:17+86RU “ “

'5,//('+2/(6381&+('+2/(6“$1*/(6“ƒ

)25/$6(5&87&20321(176

)256+((7PP$1'81'(572/(5$1&(

)256+((7WRPP72/(5$1&(

)256+((7WRPP72/(5$1&(

0$66NJ

7+58:$//.,7&20%867,%/(:$//

-(:(/63(&75()6

3$571R

$1*/(

352-(&7,21

5(9 %< (&11R '$7(

Retaining spring

0$7(5,$/ -,*

5(/($6(' (1*35

5(9 %< (&11R '$7(

0$7(5,$/

$)*$62137</7',1&,19,&725,$

5(*,67(5('2)),&(

%/$.(675((7$5$5$7

9,&725,$

5(/($6('

7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(

5(9 %< (&11R '$7(

$33' 77

6+((7

2)

7,7/(

-,*

$)*$62137</7',1&,19,&725,$

5(*,67(5('2)),&(

%/$.(675((7$5$5$7

9,&725,$

7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(

3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:

',0(16,2166+2:17+86RU “ “

(1*35

'5$:1

)256+((7WRPP72/(5$1&(

$33'

7+58:$//.,7&20%867,%/(:$//

-(:(/63(&75()6

77

77

0$66NJ

$1*/(

352-(&7,21

6&$/(

6+((7

2)

7,7/(

67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(

',0(16,2166+2:17+86RU “ “

'5,//('+2/(6381&+('+2/(6“$1*/(6“ƒ

)25/$6(5&87&20321(176

)256+((7PP$1'81'(572/(5$1&(

)256+((7WRPP72/(5$1&(

)256+((7WRPP72/(5$1&(

7+58:$//.,7&20%867,%/(:$//

-(:(/63(&75()6

3$571R

0$66NJ

7+,5'

$1*/(

352-(&7,21

'

),1,6+1$785$/

),1,6+1$785$/

'21276&$/( $

'(7$,/'

6&$/(

),1,6+1$785$/

Step 6

• Using the wall thickness measurement, determine value (y) using

the following equation:

y = wall thickness - 88mm, (± 2mm)

• Referring to figure 9, measure distance y from the front of the

pedestal base at the side pointed towards the wall. Mark and drill

a 6.5mm hole at this point, 43mm above the pedestal base on both

sides of the appliance.

Figure 9

Facing towards wall y Ø 6.5mm

43mm

Step 7

Figure 10

0$7(5,$/ -,*

• Move heater into position, central to the wall cut-out and heat

shield assembly, as per figure 10.

$)*$62137</7',1&,19,&725,$

5(*,67(5('2)),&(

%/$.(675((7$5$5$7

• Position the appliance so that the distance from the pedestal base

to the heat shield panel on the freestanding side is 575mm.

5(/($6('

9,&725,$

7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(

3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:

'5$:1 77

6&$/( 7,7/(

5(9 %< (&11R '$7( 5(9 %< (&11R '$7( $33'

6+((7

2)

67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(

',0(16,2166+2:17+86RU “ “

'5,//('+2/(6381&+('+2/(6“$1*/(6“ƒ

)25/$6(5&87&20321(176

)256+((7PP$1'81'(572/(5$1&(

)256+((7WRPP72/(5$1&(

)256+((7WRPP72/(5$1&(

%$6(+($7(5

'225+($7(5)6

3$571R

0$66NJ

),1,6+1$785$/

Step 8

• Install the rear fascia panel as shown in figure 11. Press the

locating tabs of the panel through the cut-out sections in

the heat shield panel, then secure by pushing the fascia

down until it is seated in position.

575mm

'21276&$/( $

Figure 11

'21276&$/( $

Step 9

• Using the suppied M6 fasteners, secure the

rear fascia fill panels and mount brackets in

position, as per figures 12 & 13.

• This is best carried out by first installing the

brackets, then securing the fill panels in place.

'21276&$/( $

Figure 12

),1,6+

Figure 13

5(/($6('

0$7(5,$/

5(9 %< (&11R '$7( Component assembly.

Refer to page 2 for component identification.

-,*

$)*$62137</7',1&,19,&725,$

5(*,67(5('2)),&(

%/$.(675((7$5$5$7

9,&725,$

$33'

67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(

',0(16,2166+2:17+86RU “ “

5(9 %< (&11R '$7(

7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(

3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:

'5$:1 77

6&$/( 7,7/(

6+((7

2)

)256+((7PP$1'81'(572/(5$1&(

)256+((7WRPP72/(5$1&(

)256+((7WRPP72/(5$1&(

%$6(+($7(5

'225+($7(5)6

5(/($6('

3$571R

7+,5'

$1*/(

352-(&7,21

'21276&$/(

$

0$7(5,$/ -,*

$)*$62137</7',1&,19,&725,$

5(*,67(5('2)),&(

%/$.(675((7$5$5$7

9,&725,$

7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(

3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:

'5$:1 77

6&$/( 7,7/(

$33'

6+((7

2)

67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(

',0(16,2166+2:17+86RU “ “

'5,//('+2/(6381&+('+2/(6“$1*/(6“ƒ

)25/$6(5&87&20321(176

)256+((7PP$1'81'(572/(5$1&(

)256+((7WRPP72/(5$1&(

)256+((7WRPP72/(5$1&(

%$6(+($7(5

'225+($7(5)6

3$571R

0$66NJ

7+,5'

$1*/(

352-(&7,21

5(9 %< (&11R '$7(

5(/($6('

5(9 %< (&11R '$7(

0$7(5,$/ -,*

$)*$62137</7',1&,19,&725,$

5(*,67(5('2)),&(

%/$.(675((7$5$5$7

9,&725,$

7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(

3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:

'5$:1 77

6&$/( 7,7/(

$33'

6+((7

2)

67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(

',0(16,2166+2:17+86RU “ “

'5,//('+2/(6381&+('+2/(6“$1*/(6“ƒ

)25/$6(5&87&20321(176

)256+((7PP$1'81'(572/(5$1&(

)256+((7WRPP72/(5$1&(

)256+((7WRPP72/(5$1&(

%$6(+($7(5

'225+($7(5)6

3$571R

0$66NJ

7+,5'

$1*/(

352-(&7,21

5(9 %< (&11R '$7( 5(9 %< (&11R '$7(

0$7(5,$/ -,*

$)*$62137</7',1&,19,&725,$

5(*,67(5('2)),&(

67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(

',0(16,2166+2:17+86RU “ “

%/$.(675((7$5$5$7

9,&725,$

7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(

3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:

'5$:1

$33'

77

77

6&$/(

6+((7

2)

7,7/(

'5,//('+2/(6381&+('+2/(6“$1*/(6“ƒ

)25/$6(5&87&20321(176

)256+((7PP$1'81'(572/(5$1&(

)256+((7WRPP72/(5$1&(

)256+((7WRPP72/(5$1&(

7+58:$//.,7&20%867,%/(:$//

-(:(/63(&75()6

3$571R

0$66NJ

7+,5'

$1*/(

352-(&7,21

),1,6+

),1,6+1$785$/

'21276&$/( $

),1,6+1$785$/

),1,6+1$785$/

'21276&$/(

$

'21276&$/( $

'(7$,/'

6&$/(

Step 10

• Fit the fill panel mounts using tek-screws supplied, as per figure 14.

),1,6+

Figure 14

'21276&$/( $

),1,6+1$785$/

),1,6+1$785$/

'21276&$/( $

'21276&$/( $

'

Step 11

• Connect the fan control switches (already fitted to the fill panel), ensuring connections

are made as per the diagram in appendix A. Ensure that all wiring is secured and unable

to be caught in fans or be crushed/rubbed through on heater panels.

• Note: If the fan controls have been left in the pedestal base on the freestanding

side of the installation, remove the switches fitted to the fill panel and fit the

blanking panel as per figure 14.

Figure 15

5(9 %< (&11R '$7(

),1,6+1$785$/

Step 12

• Secure the fill panel to the panel mount brackets.

• The easiest way to do this is to drive the tek-screws into the

panel mount brackets until they are around 4mm from fully

seated. Press the fill panel over the heads of the screws and

push down, locating the screws in the cut-out slots. Tighten

the tek-screws the rest of the way using a spanner.

Refer to figure 16.

Figure 16

5(9 %< (&11R '$7( 5(9 %< (&11R '$7(

0$7(5,$/

'21276&$/( $

-,*

$)*$62137</7',1&,19,&725,$

5(*,67(5('2)),&(

%/$.(675((7$5$5$7

9,&725,$

7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(

67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(

',0(16,2166+2:17+86RU “ “

'5,//('+2/(6381&+('+2/(6“$1*/(6“ƒ

)25/$6(5&87&20321(176

)256+((7PP$1'81'(572/(5$1&(

)256+((7WRPP72/(5$1&(

)256+((7WRPP72/(5$1&( 3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:

'5$:1

$33'

77

77

6&$/(

6+((7

2)

7+58:$//.,7&20%867,%/(:$//

-(:(/63(&75()6

3$571R

0$66NJ

$1*/(

352-(&7,21

Locate fill panel at these points then tighten retaining screws

0$7(5,$/ -,*

Step 13

• Fit the front fascia using 4x M8 button head bolts and washers, re-fitting the door rider

squarely and centrally on the appliance.

• Note: If the front fascia is protruding excessively from the wall, the heater should be

shifted backwards to take up this gap. Do not attempt to adjust the fascia position by

bending or shimming the fascia panel at its mounting points - This will likely interfere

with door operation. The fascia on the freestanding side should be checked to ensure

it is still sitting correctly after any adjustments are made.

Step 14

$

Figure 17

Component assembly.

Refer to page 2 for component identification.

Figure 18

5(9 %< (&11R '$7(

5(9 %< (&11R '$7(

5(/($6('

5(9 %< (&11R '$7(

5(9 %< (&11R '$7(

5(*,67(5('2)),&(

%/$.(675((7$5$5$7

9,&725,$

0$7(5,$/

$)*$62137</7',1&,19,&725,$

5(*,67(5('2)),&(

%/$.(675((7$5$5$7

9,&725,$

0$7(5,$/

5(*,67(5('2)),&(

%/$.(675((7$5$5$7

9,&725,$

7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(

3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:

77

7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(

3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:

'5$:1 77

6&$/( 7,7/(

$33'

6+((7

2)

6&$/(

$33'

)256+((7PP$1'81'(572/(5$1&(

)256+((7WRPP72/(5$1&(

)256+((7WRPP72/(5$1&(

%$6(+($7(5

7,7/(

-,*

'225+($7(5)6

77

5(/($6('

-,*

$)*$62137</7',1&,19,&725,$

5(*,67(5('2)),&(

%/$.(675((7$5$5$7

9,&725,$

)256+((7WRPP72/(5$1&(

5(9 %< (&11R '$7(

6&$/( 7,7/(

%$6(+($7(5

'225+($7(5)6

',0(16,2166+2:17+86RU “ “

'5,//('+2/(6381&+('+2/(6“$1*/(6“ƒ

)25/$6(5&87&20321(176

3$571R

0$66NJ

7+,5'

$1*/(

352-(&7,21

7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(

3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:

'5$:1

$33'

%$6(+($7(5

77

6&$/(

6+((7

2)

3$571R

7+,5'

352-(&7,21

67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(

',0(16,2166+2:17+86RU “ “

'5,//('+2/(6381&+('+2/(6“$1*/(6“ƒ

)25/$6(5&87&20321(176

)256+((7PP$1'81'(572/(5$1&(

)256+((7WRPP72/(5$1&(

)256+((7WRPP72/(5$1&(

%$6(+($7(5

'225+($7(5)6

3$571R

0$66NJ

7+,5'

$1*/(

352-(&7,21

• Re-fit the door to the appliance, ensuring that it opens and closes correctly. If the door does

not latch correctly, refer to the user manual supplied with the appliance for door adjustment

procedures. If required, use the spray can supplied to touch up the paint on the thru-wall kit

and `the appliance, following the directions on the spray can.

0$7(5,$/ -,*

5(9 %< (&11R '$7(

0$7(5,$/

5(9 %< (&11R '$7(

-,*

$)*$62137</7',1&,19,&725,$

5(*,67(5('2)),&(

67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(

',0(16,2166+2:17+86RU “ “

%/$.(675((7$5$5$7

9,&725,$

7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(

3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:

'5$:1

$33'

77

77

6&$/(

6+((7

2)

7,7/(

'5,//('+2/(6381&+('+2/(6“$1*/(6“ƒ

)25/$6(5&87&20321(176

)256+((7PP$1'81'(572/(5$1&(

)256+((7WRPP72/(5$1&(

)256+((7WRPP72/(5$1&(

7+58:$//.,7&20%867,%/(:$//

-(:(/63(&75()6

3$571R

0$66NJ

7+,5'

$1*/(

352-(&7,21

5(/($6('

5(9 %< (&11R '$7(

5(9 %< (&11R '$7(

5(/($6('

$)*$62137</7',1&,19,&725,$

5(*,67(5('2)),&(

%/$.(675((7$5$5$7

9,&725,$

7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(

3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:

'5$:1 77

0$7(5,$/

6&$/( 7,7/(

$33'

5(9 %< (&11R '$7(

%/$.(675((7$5$5$7

9,&725,$

7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(

3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:

'5$:1 77

6&$/( 7,7/(

$33'

6+((7

2)

6+((7

2)

67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(

',0(16,2166+2:17+86RU “ “

'5,//('+2/(6381&+('+2/(6“$1*/(6“ƒ

)25/$6(5&87&20321(176

)256+((7PP$1'81'(572/(5$1&(

)256+((7WRPP72/(5$1&(

)256+((7WRPP72/(5$1&(

%$6(+($7(5

'225+($7(5)6

-,*

3$571R

67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(

',0(16,2166+2:17+86RU “ “

'5,//('+2/(6381&+('+2/(6“$1*/(6“ƒ

)25/$6(5&87&20321(176

)256+((7PP$1'81'(572/(5$1&(

)256+((7WRPP72/(5$1&(

)256+((7WRPP72/(5$1&(

%$6(+($7(5

'225+($7(5)6

3$571R

0$66NJ

0$66NJ

7+,5'

$1*/(

352-(&7,21

Any enquiries contact the dealer from whom you purchased your heater.

PLEASE COMPLETE:

Dealer name:

Dealer Address:

Please attach your original purchase dockets to this instruction book for future reference.

Phone Number:

Heating

Phone (03) 9729 1422

Fax (03) 9729 1455

Gason Heating reserves the right to modify or alter specifications, materials, etc in the interests of product improvement.

F:\Docs\Manuals\Heaters\Heaters\GPN 234969 Jewel Spectre Thru Wall