advertisement
UIser Guide
User Gui
© Copyright 2006 Hewlett-Packard
Development Company, L.P.
The information contained herein is subject to change without notice.
Reproduction, adaptation or translation without prior written permission is prohibited, except as allowed under copyright laws.
Adobe® and the Acrobat logo® are trademarks of Adobe Systems
Incorporated.
Windows®, Windows NT®, Windows
ME®, Windows XP®, and Windows
2000® are U.S. registered trademarks of Microsoft Corporation.
Intel® and Pentium® are trademarks or registered trademarks of Intel
Corporation or its subsidiaries in the
United States and other countries.
October 2006
Notice
The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
The Hewlett-Packard Company shall not be liable for incidental or consequential damages in connection with, or arising out of the furnishing, performance, or use of this document and the program material which it describes.
Note: Regulatory information can be found in
It is not lawful in many places to make copies of the following items. When in doubt, check with a legal representative first.
• Governmental paper or documents:
• Passports
• Immigration papers
• Selective service papers
• Identification badges, cards, or insignias
• Governmental stamps:
• Postage stamps
• Food stamps
• Checks or drafts drawn on
Governmental agencies
• Paper currency, traveler’s checks, or money orders
• Certificates of deposit
• Copyrighted works
Safety information
WARNING!
To prevent fire or shock hazard, do not expose this product to rain or any type of moisture.
Always follow basic safety precautions when using this product to reduce risk of injury from fire or electric shock.
WARNING!
Potential shock hazard
1.
Read and understand all instructions in the Setup Guide.
2.
Use only a grounded electrical outlet when connecting the device to a power source. If you do not know whether the outlet is grounded, check with a qualified electrician.
3.
Observe all warnings and instructions marked on the product.
4.
Unplug this product from wall outlets before cleaning.
5.
Do not install or use this product near water or when you are wet.
6.
Install the product securely on a stable surface.
7.
Install the product in a protected location where no one can step on or trip over the power cord, and where the power cord will not be damaged.
8.
If the product does not operate normally, see the onscreen
Troubleshooting help.
9.
No operator-serviceable parts inside. Refer servicing to qualified service personnel.
10.
Use in a well-ventilated area.
11.
Use only with the power adapter supplied by HP.
WARNING!
This equipment will be inoperable when main power fails.
Contents
1
4 Finish setting up the HP All-in-One
Set up the HP All-in-One to redial a fax number automatically....................................21
Case C: Set up the HP All-in-One with a PBX phone system or an ISDN line.............31
Case H: Shared voice/fax line with computer dial-up modem......................................37
Case K: Shared voice/fax line with computer dial-up modem and voice mail..............43
Choose the recommended answer mode for your setup..............................................45
5 Load originals and load paper
2
Contents
3
Send a fax from the HP Photosmart Studio (Mac) Software........................................99
Send a computer-generated cover page as a single-page fax...................................100
4
Contents
5
Disposal of Waste Equipment by Users in Private Households in the European
Notice to users of the U.S. telephone network: FCC requirements..................................281
6
1 HP Officejet J5700 All-in-
One series Help
For information about the HP All-in-One, see:
•
•
•
Finish setting up the HP All-in-One
•
•
•
•
•
•
•
•
•
•
HP Officejet J5700 All-in-One series Help 7
Chapter 1
8 HP Officejet J5700 All-in-One series Help
2 Find more information
You can access a variety of resources, both printed and onscreen, that provide information about setting up and using the HP All-in-One.
•
Sources of information
Setup Poster
The Setup Poster provides instructions for setting up your HP All-in-One and installing software. Make sure you follow the steps in the Setup Poster in order.
www.hp.com/support
User Guide
This User Guide contains information on how to use your HP All-in-One, including troubleshooting tips and step-by-step instructions. It also provides additional setup instructions to supplement those in the Setup Poster.
Readme
The Readme file contains the most recent information which might not be found in other publications.
Install the software to access the Readme file.
If you have Internet access, you can get help and support from the HP website.
This website offers technical support, drivers, supplies, and ordering information.
Find more information 9
Chapter 2
10 Find more information
3 HP All-in-One overview
You can access many HP All-in-One functions directly, without turning on your computer.
You can quickly and easily accomplish tasks such as making a copy or sending a fax from the HP All-in-One.
This section describes the HP All-in-One hardware features and control panel functions.
This section contains the following topics:
•
•
•
•
•
The HP All-in-One at a glance
5
6
7
2
3
Label
1
4
Description
Automatic document feeder
Control panel
Control panel display (also referred to as the display)
Output tray extender (also referred to as the tray extender)
Input tray
Output tray
Glass
HP All-in-One overview 11
Chapter 3
(continued)
Label
8
9
10
11
12
Description
Lid backing
Rear door
Rear USB port
Power connection
1-LINE (fax) and 2-EXT (phone) ports
Control panel features
The following diagram and related table provide a quick reference to the HP All-in-One control panel features.
9
10
11
5
6
3
4
7
8
Label
1
2
Name and Description
Menu in the Fax area: Presents the Fax Menu for selecting options.
Redial/Pause: Redials the most recently dialed number, or insert a 3-second pause in a fax number.
Start Fax Black: Starts a black-and-white fax.
Start Fax Color: Starts a color fax.
One-touch speed dial buttons: Access the first five speed dial numbers.
Keypad: Enters fax numbers, values, or text.
Attention light: When blinking, the attention light indicates an error that requires your attention has occurred.
Setup/?: Presents the Setup Menu for generating reports, changing fax and other maintenance settings, and accessing the Help menu. Press to scroll through the Help topics available, and then press OK to select a topic. The Help topic you select opens on your computer screen.
Left arrow: Decreases values on the display.
OK: Selects a menu or a setting on the display.
Right arrow: Increases values on the display.
12 HP All-in-One overview
18
19
20
21
22
23
(continued)
Label
12
13
14
15
16
17
Name and Description
Cancel: Stops a job, exits a menu, or exits settings.
Start Copy Black: Starts a black-and-white copy job.
Start Copy Color: Starts a color copy job.
Start Scan: Starts a scan job and sends it to the destination you selected using the Scan To button.
Scan To: Presents the Scan To menu for selecting a scan destination.
Power: Turns the HP All-in-One on or off. The On button is lit when the HP All-in-One is on. The light blinks while performing a job.
When the HP All-in-One is off, a minimal amount of power is still supplied to the device. To completely disconnect the power supply to the HP All-in-One, turn the device off, and then unplug the power cord.
Quality: Selects Best, Normal, or Fast quality for copying.
Reduce/Enlarge: Changes the size of a copy for printing.
Menu in the Copy area: Presents the Copy Menu for selecting options.
Display: View menus and messages.
Speed Dial: Selects a speed dial number.
The functionality of this button depends on the country/region in which the HP All-in-One is sold.
The button name is one of the following:
Fax Resolution: Adjusts the resolution for the fax you are sending.
Junk Fax Blocker: Presents the Junk Fax Blocker Set Up menu for managing unwanted fax calls. You are required to subscribe to a caller ID service with your phone company to use this feature.
Text and symbols
You can use the control panel keypad to enter text and symbols when you set up speed dial entries and the fax header information.
You can also enter symbols from the keypad when you dial a fax or phone number. When the HP All-in-One dials the number, it will interpret the symbol and respond accordingly.
For example, if you enter a dash in the fax number, the HP All-in-One will pause before dialing the remainder of the number. A pause is useful if you need to access an outside line before dialing the fax number.
This section contains the following topics:
•
Enter text using the keypad on the control panel
•
Available symbols for dialing fax numbers
Enter text using the keypad on the control panel
You can enter text or symbols by using the keypad on the control panel.
Text and symbols 13
Chapter 3
To enter text
1.
Press the keypad numbers that correspond to the letters of a name. For example, the letters a, b, and c correspond to the number 2, as shown on the button below.
TIP:
Press a button multiple times to see the available characters. Depending on your language and country/region setting, other characters might be available in addition to the ones shown on the keypad.
2.
After the correct letter appears, wait for the cursor to advance automatically to the right, or press . Press the number that corresponds to the next letter in the name.
Press the button multiple times until the correct letter appears. The first letter of a word is automatically set to uppercase.
To enter a space, pause, or symbol
▲ To insert a space, press Space.
To enter a pause, press Redial/Pause. A dash appears in the number sequence.
To enter a symbol, such as @, press the Symbols button repeatedly to scroll through the list of available symbols.
asterisk (*) period (.) apostrophe (') at (@) exclamation (!) comma (,) approximation (~) dash (-) slash (/) equals (=) underscore (_) semicolon (;) colon (:) ampersand (&) parentheses ( ) number sign (#) plus (+) question (?) percent (%)
To erase a letter, number, or symbol
▲ If you make a mistake, press to clear it, and then make the correct entry.
After you are done entering text, press OK to store your entry.
Available symbols for dialing fax numbers
To enter a symbol, such as *, press Symbols repeatedly to scroll through the list of symbols. The following table provides the symbols that you can use in a fax or phone number sequence, fax header information, and speed dial entries.
Description Available when entering Available symbols
* Displays an asterisk symbol when required for dialing.
Fax header name, speed dial names, speed dial numbers, fax or
14 HP All-in-One overview
R
+
(continued)
Available symbols
-
( )
W
Description Available when entering
When auto-dialing, the HP All-in-One enters a pause in the number sequence.
Displays a left or right parenthesis to separate numbers, such as area codes, for easier reading. These symbols do not affect dialing.
When auto-dialing, W causes the HP Allin-One to wait for a dial tone before continuing to dial.
During auto-dialing, the R functions the same as a Flash button on your telephone.
Displays a plus symbol. This symbol does not affect dialing.
phone numbers, and monitor dial entries
Fax header name, fax header number, speed dial names, speed dial numbers, and fax or phone numbers
Fax header name, fax header number, speed dial names, speed dial numbers, and fax or phone numbers
Speed dial numbers and fax or phone numbers
Speed dial numbers and fax or phone numbers
Fax header name, fax header number, speed dial names, speed dial numbers, and fax or phone numbers
Use the software
You can use the HP Solution Center Software (Windows) or HP Photosmart Studio (Mac)
Software (Mac) to access many features not available from the control panel.
The software is installed on your computer when you set up the HP All-in-One. For further information, see the Setup Poster that came with your device.
Access to the software differs by operating system (OS). For example, if you have a
Windows computer, the HP Solution Center Software entry point is the HP Solution
Center. If you have a Mac, the HP Photosmart Studio (Mac) Software entry point is the
HP Photosmart Studio window. Regardless, the entry point serves as the launching pad for the software and services.
To open HP Photosmart Studio (Mac)
▲ Click the HP Photosmart Studio icon in the Dock.
The HP Photosmart Studio window appears, where you can manage, edit, and share photos.
NOTE:
On a Mac, the features available in the HP Photosmart Studio (Mac) software vary depending on the chosen device.
Connection information
You can use the HP All-in-One as a stand-alone copier and fax machine, or you can connect the HP All-in-One to a computer to enable printing and other software features.
The different connection options available to you are described in the following sections.
Use the software 15
Chapter 3
This section contains the following topics:
•
•
•
Supported connection types
Description
USB connection
Printer sharing
Recommended number of connected computers for best performance
One computer connected with a USB cable to the rear USB port.
Up to five computers.
The host computer must be turned on at all times, or the other computers will not be able to print to the
HP All-in-One.
Supported software features
All features are supported.
All features are available on the host computer. The computers connected to the host computer can only access the print feature.
Setup instructions
Follow the Setup
Poster for detailed instructions.
For setup instructions, see
.
Connect using a USB cable
Refer to the Setup Poster that came with the HP All-in-One for detailed instructions on using a USB cable to connect a computer to the rear USB port.
Use printer sharing
If your computer is on a network, and another computer on the network has an HP Allin-One connected to it by a USB cable, you can print to that printer using printer sharing.
The computer directly connected to the HP All-in-One acts as the host for the printer and has full software functionality. The other computer, which is referred to as a client, has access only to the print features. You must perform other functions from the host computer or from the control panel on the HP All-in-One.
16 HP All-in-One overview
To enable printer sharing on a Mac
1.
On both the client and host computers, do the following:
a. Click System Preferences in the Dock, or, from the Apple menu, choose System
Preferences.
The System Preferences dialog appears.
b. In the Internet & Network area, click Sharing.
c. From the Services tab, click Printer Sharing.
2.
On the host computer, do the following:
a. Click System Preferences in the Dock, or, from the Apple menu, choose System
Preferences.
The System Preferences dialog appears.
b. In the Hardware area, click Print & Fax.
c. Do one of the following, depending on your OS:
• (OS 10.3.x) From the Printing tab, click the check box to Share my printers
with other computers.
• (OS 10.4.x) Click Sharing, click the check box to Share this printer with
other computers, and then select the printer to share.
Connection information 17
Chapter 3
18 HP All-in-One overview
4 Finish setting up the HP All-in-
One
After you have completed the steps in your Setup Poster, refer to this section to help you finish setting up the HP All-in-One. This section contains important setup-related information for your device, including information on setting preferences.
This section contains the following topics:
•
•
Set your preferences
You can change the settings on the HP All-in-One so that it behaves according to your preference. For example, you can set general device preferences, such as the language used to display messages and the date and time on the display. You can also restore the device settings to what they were when you purchased your device. This will erase any new defaults you have set.
This section contains the following topics:
•
•
General preferences
Before you begin using the HP All-in-One, you should review and, if necessary, adjust the general device settings described in this section.
This section contains the following topics:
•
Set your language and country/region
•
•
•
•
Set your language and country/region
The language and country/region setting determines which language the HP All-in-One uses to show messages on the display. Usually, you set the language and country/region when you first set up the HP All-in-One. However, you can change the setting at any time by using the following procedure.
To set your language and country/region
1.
Press Setup.
2.
Press 7, and then press 1.
This selects Preferences and then selects Set Language & Country/Region.
Finish setting up the HP All-in-One 19
Chapter 4
3.
Press or to scroll through the languages. When the language you want to use appears, press OK.
4.
When prompted, press 1 for Yes or 2 for No.
5.
Press or to scroll through the countries/regions. When the country/region you want to select appears, press OK.
6.
When prompted, press 1 for Yes or 2 for No.
Set the date and time
You can set the date and time from the control panel. The date and time format is based on the language and country/region setting. When you send a fax, the current date and time are transmitted, along with your name and fax number, as part of the fax header.
NOTE:
In some countries/regions, the date and time stamp on the fax header is a legal requirement.
If the HP All-in-One loses power for more than 72 hours, you might need to reset the date and time.
To set the date and time
1.
Press Setup.
2.
Press 6, and then press 3.
This selects Tools and then selects Date and Time.
3.
Enter the month, day, and year by pressing the appropriate numbers on the keypad.
Depending on your country/region setting, you might enter the date in a different order.
4.
Enter the hours and minutes.
5.
If your time is displayed in the 12-hour format, press 1 for AM, or 2 for PM.
The new date and time settings appear on the display.
Set the scroll speed
The Set Scroll Speed option enables you to control the rate at which text messages scroll from right to left on the display. For example, if the message is "Aligning
cartridges, please wait.", it will not completely fit in the display and will need to scroll.
This is so that you can read the entire message. You can choose the rate at which it will scroll: Normal, Fast, or Slow. The default is Normal.
To set the scroll speed
1.
Press Setup.
2.
Press 7, then press 2.
This selects Preferences and then selects Set Scroll Speed.
3.
Press to select a scroll speed, then press OK.
Set the prompt delay time
The Set Prompt Delay Time option enables you to control the amount of time that passes before a message prompts you to take further action.
20 Finish setting up the HP All-in-One
For example, if you press Menu in the Copy area and the prompt delay time passes before you press another button, the message "Press Menu for settings." appears on the display.
To set the prompt delay time
1.
Press Setup.
2.
Press 7, then press 3.
This selects Preferences and then selects Set Prompt Delay Time.
3.
Press to select a delay time, then press OK.
You can choose Normal, Fast, Slow, or Off. If you select Off, hints do not appear on the display but other messages, such as low ink warnings and error messages, do still appear.
Restore the factory defaults
You can restore the current settings to what they were when you purchased the HP Allin-One.
NOTE:
Restoring the factory defaults will not affect any changes you made to scan settings and the language and country/region settings. Personal settings and lists, for example fax header, fax number, junk fax list, and speed dial list, that you have saved will not be deleted when restoring the factory defaults.
You can perform this process from the control panel only.
To restore the factory defaults
1.
Press Setup.
2.
Press 6, then press 4.
This selects Tools and then selects Restore Factory Defaults.
The factory default settings are restored.
Fax preferences
This section contains the following topics:
•
Set up the HP All-in-One to redial a fax number automatically
•
•
•
Set up the HP All-in-One to redial a fax number automatically
You can set the HP All-in-One to redial a busy or an unanswered number automatically.
The default Busy Redial setting is Redial. The default No Answer Redial setting is No
Redial.
Set your preferences 21
Chapter 4
22
To set redial options from the control panel
1.
Press Setup.
2.
Do one of the following:
To change the Busy Redial setting
▲ Press 5, and then press 2.
This selects Advanced Fax Setup and then selects Busy Redial.
To change the No Answer Redial setting
▲ Press 5, and then press 3.
This selects Advanced Fax Setup and then selects No Answer Redial.
3.
Press to select Redial or No Redial.
4.
Press OK.
Adjust the volume
The HP All-in-One provides three levels for adjusting the ring and speaker volume. The ring volume is the volume of the phone rings. The speaker volume is the level of everything else, such as the dial tones, fax tones, and button press beeps. The default setting is Soft.
To adjust the volume from the control panel
1.
Press Setup.
2.
Press 4, and then press 5 again.
This selects Basic Fax Setup and then selects Ring and Beep Volume.
3.
Press to select one of the options: Soft, Loud, or Off.
NOTE:
The beeps you hear when pressing buttons maintain the same volume whether you choose Loud or Soft. These two options only affect ring, dial, and other tones you hear when faxing. If you choose Off, however, the sounds of button presses are also turned off.
If you select Off, you will not hear a dial tone, fax tones, or incoming ring tones.
With the Ring and Beep Volume set to Off, you cannot send a fax using monitor dialing, such as when using a calling card to send a fax.
4.
Press OK.
Related topics
Send a fax using monitor dialing
Set tone or pulse dialing
You can set the dial mode for the HP All-in-One to either tone dialing or pulse dialing.
Most telephone systems work with either type of dialing. If your telephone system does not require pulse dialing, HP recommends using tone dialing. If you have a public telephone system or a private branch exchange (PBX) system, you might need to select Pulse Dialing. Contact your local telephone company if you are unsure which setting to use.
Finish setting up the HP All-in-One
NOTE:
If you select Pulse Dialing, some phone system features might not be available. It can also take longer to dial a fax or phone number.
NOTE:
This feature is not supported in all countries/regions. If it is not supported in your country/region, Tone or Pulse Dialing does not appear in the Basic Fax
Setup menu.
To set tone or pulse dialing from the control panel
1.
Press Setup.
2.
Press 4, and then press 6.
This selects Basic Fax Setup and then selects Tone or Pulse Dialing.
3.
Press to select an option, and then press OK.
Set the fax speed
You can set the fax speed used to communicate between the HP All-in-One and other fax machines when sending and receiving faxes. The default fax speed varies by country/ region.
If you use one of the following, setting the fax speed to a slower speed might be required:
• An Internet phone service
• A PBX system
• Fax over Internet Protocol (FoIP)
• An integrated services digital network (ISDN) service
If you experience problems sending and receiving faxes, you might want to try setting the Fax Speed setting to Medium or Slow.
To set the fax speed from the control panel
1.
Press Setup.
2.
Press 5, and then press 7.
This selects Advanced Fax Setup and then selects Fax Speed.
3.
Press to select one of the following settings, and then press OK.
Fax speed setting
Fast
Medium
Slow
Fax speed
v.34 (33600 baud) v.17 (14400 baud) v.29 (9600 baud)
Fax setup
In this section, you will learn how to set up the HP All-in-One so that faxing works successfully with equipment and services you might already have on the same phone line as the HP All-in-One.
Fax setup 23
Chapter 4
TIP:
You can also use the Fax Setup Wizard (Windows) or Fax Setup Utility (Mac) to help you quickly set up some important fax settings such as the answer mode and fax header information. You can access the Fax Setup Wizard (Windows) or Fax
Setup Utility (Mac) through the software you installed with the HP All-in-One. After you run the Fax Setup Wizard (Windows) or Fax Setup Utility (Mac), follow the procedures in this section to complete your fax setup.
This section contains the following topics:
•
Set up the HP All-in-One for faxing
•
Change settings on the HP All-in-One to receive faxes
•
•
•
•
Set up the HP All-in-One for faxing
Before you begin setting up the HP All-in-One for faxing, determine which kind of phone system your country/region uses. The instructions for setting up the HP All-in-One for faxing differ depending on whether you have a serial- or parallel-type phone system.
• If you do not see your country/region listed in the table below, you probably have a serial-type phone system. In a serial-type phone system, the connector type on your shared telephone equipment (modems, phones, and answering machines) does not allow a physical connection to the "2-EXT" port on the HP All-in-One. Instead, all equipment must be connected at the telephone wall jack.
NOTE:
In some countries/regions that use serial-type phone systems, the phone cord that came with the HP All-in-One might have an additional wall plug attached to it. This enables you to connect other telecom devices to the wall jack where you plug in the HP All-in-One.
• If your country/region is listed in the table below, you probably have a parallel-type telephone system. In a parallel-type phone system, you are able to connect shared telephone equipment to the phone line by using the "2-EXT" port on the back of the
HP All-in-One.
NOTE:
If you have a parallel-type phone system, HP recommends you use the
2-wire phone cord supplied with the HP All-in-One to connect the HP All-in-One to the telephone wall jack.
Table 4-1 Countries/regions with a parallel-type phone system
Argentina Australia Brazil
Canada
Colombia
Indonesia
Korea
Chile
Greece
Ireland
Latin America
China
India
Japan
Malaysia
24 Finish setting up the HP All-in-One
Countries/regions with a parallel-type phone system (continued)
Mexico Philippines
Portugal Russia
Singapore
Thailand
Vietnam
Spain
USA
Poland
Saudi Arabia
Taiwan
Venezuela
If you are unsure which kind of telephone system you have (serial or parallel), check with your telephone company.
•
Choose the correct fax setup for your home or office
•
•
Case A: Separate fax line (no voice calls received)
•
Case B: Set up the HP All-in-One with DSL
•
Case C: Set up the HP All-in-One with a PBX phone system or an ISDN line
•
Case D: Fax with a distinctive ring service on the same line
•
•
Case F: Shared voice/fax line with voice mail
•
Case G: Fax line shared with computer dial-up modem (no voice calls received)
•
Case H: Shared voice/fax line with computer dial-up modem
•
Case I: Shared voice/fax line with answering machine
•
Case J: Shared voice/fax line with computer dial-up modem and answering machine
•
Case K: Shared voice/fax line with computer dial-up modem and voice mail
Choose the correct fax setup for your home or office
To fax successfully, you need to know what types of equipment and services (if any) share the same phone line with the HP All-in-One. This is important because you might need to connect some of your existing office equipment directly to the HP All-in-One, and you might also need to change some fax settings before you can fax successfully.
To determine the best way to set up the HP All-in-One in your home or office, first read through the questions in this section and record your answers. Next, refer to the table in the following section and choose the recommended setup case based on your answers.
Make sure to read and answer the following questions in the order they are presented.
1.
Do you have a digital subscriber line (DSL) service through your telephone company?
(DSL might be called ADSL in your country/region.)
❑ Yes, I have DSL.
❑ No.
If you answered Yes, proceed directly to Case B: Set up the HP All-in-One with
DSL . You do not need to continue answering questions.
If you answered No, please continue answering questions.
2.
Do you have a private branch exchange (PBX) phone system or an integrated services digital network (ISDN) system?
If you answered Yes, proceed directly to Case C: Set up the HP All-in-One with a
PBX phone system or an ISDN line
. You do not need to continue answering questions.
If you answered No, please continue answering questions.
Fax setup 25
Chapter 4
3.
Do you subscribe to a distinctive ring service through your telephone company that provides multiple phone numbers with different ring patterns?
❑ Yes, I have distinctive ring.
❑ No.
If you answered Yes, proceed directly to
Case D: Fax with a distinctive ring service on the same line
. You do not need to continue answering questions.
If you answered No, please continue answering questions.
Are you unsure if you have distinctive ring? Many phone companies offer a distinctive ring feature that allows you to have several phone numbers on one phone line.
When you subscribe to this service, each phone number will have a different ring pattern. For example, you can have single, double, and triple rings for the different numbers. You might assign one phone number with a single ring to your voice calls, and another phone number with double rings to your fax calls. This allows you to tell the difference between voice and fax calls when the phone rings.
4.
Do you receive voice calls at the same phone number you will use for fax calls on the
HP All-in-One?
❑ Yes, I receive voice calls.
❑ No.
Please continue answering questions.
5.
Do you have a computer dial-up modem on the same phone line as the HP All-in-
One?
❑ Yes, I have a computer dial-up modem.
❑ No.
Are you unsure if you use a computer dial-up modem? If you answer Yes to any of the following questions, you are using a computer dial-up modem:
• Do you send and receive faxes directly to and from your computer software applications through a dial-up connection?
• Do you send and receive e-mail messages on your computer through a dial-up connection?
• Do you access the Internet from your computer through a dial-up connection?
Please continue answering questions.
6.
Do you have an answering machine that answers voice calls at the same phone number you will use for fax calls on the HP All-in-One?
❑ Yes, I have an answering machine.
❑ No.
Please continue answering questions.
7.
Do you subscribe to a voice mail service through your telephone company at the same phone number you will use for fax calls on the HP All-in-One?
❑ Yes, I have a voice mail service.
❑ No.
After you have completed answering the questions, proceed to the next section to select your fax setup case.
26 Finish setting up the HP All-in-One
Select your fax setup case
Now that you have answered all the questions about the equipment and services that share the phone line with the HP All-in-One, you are ready to choose the best setup case for your home or office.
From the first column in the following table, choose the combination of equipment and services applicable to your home or office setting. Then look up the appropriate setup case in the second or third column based on your phone system. Step-by-step instructions are included for each case in the sections that follow.
If you have answered all the questions in the previous section and have none of the described equipment or services, choose "None" from the first column in the table.
NOTE:
If your home or office setup is not described in this section, set up the HP Allin-One as you would a regular analog phone. Make sure you use the phone cord supplied in the box to connect one end to your telephone wall jack and the other end to the port labeled 1-LINE on the back of the HP All-in-One. If you use another phone cord, you might experience problems sending and receiving faxes.
Other equipment/services sharing your fax line
None
(You answered No to all questions.)
DSL service
(You answered Yes to question
1 only.)
PBX or ISDN system
(You answered Yes to question
2 only.)
Distinctive ring service
(You answered Yes to question
3 only.)
Voice calls
(You answered Yes to question
4 only.)
Voice calls and voice mail service
(You answered Yes to questions 4 and 7 only.)
Computer dial-up modem
(You answered Yes to question
5 only.)
Voice calls and computer dialup modem
(You answered Yes to questions 4 and 5 only.)
Recommended fax setup for parallel-type phone systems
Case A: Separate fax line (no voice calls received)
Recommended fax setup for serial-type phone systems
Case A: Separate fax line (no voice calls received)
One with a PBX phone system or an ISDN line
One with a PBX phone system or an ISDN line
Case D: Fax with a distinctive ring service on the same line
Case F: Shared voice/fax line with voice mail
Case G: Fax line shared with computer dial-up modem (no voice calls received)
Case H: Shared voice/fax line with computer dial-up modem
Case D: Fax with a distinctive ring service on the same line
Case E: Shared voice/fax line Case E: Shared voice/fax line
Case F: Shared voice/fax line with voice mail
Not applicable.
Not applicable.
Fax setup 27
Chapter 4
(continued)
Other equipment/services sharing your fax line
Voice calls and answering machine
(You answered Yes to questions 4 and 6 only.)
Voice calls, computer dial-up modem, and answering machine
(You answered Yes to questions 4, 5, and 6 only.)
Voice calls, computer dial-up modem, and voice mail service
(You answered Yes to questions 4, 5, and 7 only.)
Recommended fax setup for parallel-type phone systems
Case I: Shared voice/fax line with answering machine
Case J: Shared voice/fax line with computer dial-up modem and answering machine
Case K: Shared voice/fax line with computer dial-up modem and voice mail
Recommended fax setup for serial-type phone systems
Not applicable.
Not applicable.
Not applicable.
For additional fax setup information, in specific countries/regions, see the Fax
Configuration Web site listed below.
Austria
Germany
Switzerland (French)
Switzerland (German)
United Kingdom
Spain
The Netherlands
Belgium (France)
Belgium (Dutch)
Portugal
Sweden
Finland
Denmark
Norway
Ireland
France
Italy www.hp.com/at/faxconfig www.hp.com/de/faxconfig www.hp.com/ch/fr/faxconfig www.hp.com/ch/de/faxconfig www.hp.com/uk/faxconfig www.hp.es/faxconfig www.hp.nl/faxconfig www.hp.be/fr/faxconfig www.hp.be/nl/faxconfig www.hp.pt/faxconfig www.hp.se/faxconfig www.hp.fi/faxconfig www.hp.dk/faxconfig www.hp.no/faxconfig www.hp.com/ie/faxconfig www.hp.com/fr/faxconfig www.hp.com/it/faxconfig
28 Finish setting up the HP All-in-One
Case A: Separate fax line (no voice calls received)
If you have a separate phone line on which you receive no voice calls, and you have no other equipment connected on this phone line, set up the HP All-in-One as described in this section.
Figure 4-1 Back view of the HP All-in-One
1 Telephone wall jack
2 Use the phone cord supplied in the box with the HP All-in-One to connect to the "1-LINE" port
To set up the HP All-in-One with a separate fax line
1.
Using the phone cord supplied in the box with the HP All-in-One, connect one end to your telephone wall jack, then connect the other end to the port labeled 1-LINE on the back of the HP All-in-One.
NOTE:
If you do not use the supplied cord to connect from the telephone wall jack to the HP All-in-One, you might not be able to fax successfully. This special phone cord is different from the phone cords you might already have in your home or office.
2.
Turn on the Auto Answer setting.
3.
(Optional) Change the Rings to Answer setting to the lowest setting (two rings).
4.
Run a fax test.
When the phone rings, the HP All-in-One will answer automatically after the number of rings you set in the Rings to Answer setting. Then it will begin emitting fax reception tones to the sending fax machine and receive the fax.
Case B: Set up the HP All-in-One with DSL
If you have a DSL service through your telephone company, use the instructions in this section to connect a DSL filter between the telephone wall jack and the HP All-in-One.
The DSL filter removes the digital signal that can interfere with the HP All-in-One, so the
HP All-in-One can communicate properly with the phone line. (DSL might be called ADSL in your country/region.)
NOTE:
If you have a DSL line and you do not connect the DSL filter, you will not be able to send and receive faxes with the HP All-in-One.
Fax setup 29
Chapter 4
Figure 4-2 Back view of the HP All-in-One
1 Telephone wall jack
2 DSL filter and cord supplied by your DSL provider
3 Use the phone cord supplied in the box with the HP All-in-One to connect to the "1-LINE" port
To set up the HP All-in-One with DSL
1.
Obtain a DSL filter from your DSL provider.
2.
Using the phone cord supplied in the box with the HP All-in-One, connect one end to your telephone wall jack, then connect the other end to the port labeled 1-LINE on the back of the HP All-in-One.
NOTE:
If you do not use the supplied cord to connect from the telephone wall jack to the HP All-in-One, you might not be able to fax successfully. This special phone cord is different from the phone cords you might already have in your home or office.
3.
Connect the DSL filter cord to the telephone wall jack.
NOTE:
If you have other office equipment or services attached to this phone line, such as a distinctive ring service, answering machine, or voice mail, see the appropriate section in this section for additional setup guidelines.
4.
Run a fax test.
30 Finish setting up the HP All-in-One
Case C: Set up the HP All-in-One with a PBX phone system or an ISDN line
If you are using either a PBX phone system or an ISDN converter/terminal adapter, make sure you do the following:
• If you are using either a PBX or an ISDN converter/terminal adaptor, connect the
HP All-in-One to the port that is designated for fax and phone use. Also, make sure that the terminal adapter is set to the correct switch type for your country/region, if possible.
NOTE:
Some ISDN systems allow you to configure the ports for specific phone equipment. For example, you might have assigned one port for telephone and
Group 3 fax and another port for multiple purposes. If you have problems when connected to the fax/phone port of your ISDN converter, try using the port designated for multiple purposes; it might be labeled "multi-combi" or something similar.
• If you are using a PBX phone system, set the call waiting tone to "off".
NOTE:
Many digital PBX systems include a call-waiting tone that is set to "on" by default. The call waiting tone will interfere with any fax transmission, and you will not be able to send or receive faxes with the HP All-in-One. Refer to the documentation that came with your PBX phone system for instructions on how to turn off the call-waiting tone.
• If you are using a PBX phone system, dial the number for an outside line before dialing the fax number.
• Make sure you use the supplied cord to connect from the telephone wall jack to the
HP All-in-One. If you do not, you might not be able to fax successfully. This special phone cord is different from the phone cords you might already have in your home or office. If the supplied phone cord is too short, you can purchase a coupler from your local electronics store and extend it.
Fax setup 31
Chapter 4
Case D: Fax with a distinctive ring service on the same line
If you subscribe to a distinctive ring service (through your telephone company) that allows you to have multiple phone numbers on one phone line, each with a different ring pattern, set up the HP All-in-One as described in this section.
Figure 4-3 Back view of the HP All-in-One
1 Telephone wall jack
2 Use the phone cord supplied in the box with the HP All-in-One to connect to the "1-LINE" port
To set up the HP All-in-One with a distinctive ring service
1.
Using the phone cord supplied in the box with the HP All-in-One, connect one end to your telephone wall jack, then connect the other end to the port labeled 1-LINE on the back of the HP All-in-One.
NOTE:
If you do not use the supplied cord to connect from the telephone wall jack to the HP All-in-One, you might not be able to fax successfully. This special phone cord is different from the phone cords you might already have in your home or office.
2.
Turn on the Auto Answer setting.
3.
Change the Distinctive Ring setting to match the pattern that the telephone company assigned to your fax number.
NOTE:
By default, the HP All-in-One is set to answer all ring patterns. If you do not set the Distinctive Ring to match the ring pattern assigned to your fax number, the HP All-in-One might answer both voice calls and fax calls or it might not answer at all.
4.
(Optional) Change the Rings to Answer setting to the lowest setting (two rings).
5.
Run a fax test.
The HP All-in-One will automatically answer incoming calls that have the ring pattern you selected (Distinctive Ring setting) after the number of rings you selected (Rings to
Answer setting). Then it will begin emitting fax reception tones to the sending fax machine and receive the fax.
32 Finish setting up the HP All-in-One
Case E: Shared voice/fax line
If you receive both voice calls and fax calls at the same phone number, and you have no other office equipment (or voice mail) on this phone line, set up the HP All-in-One as described in this section.
Figure 4-4 Back view of the HP All-in-One
1 Telephone wall jack
2 Use the phone cord supplied in the box with the HP All-in-One to connect to the "1-LINE" port
3 Telephone (optional)
To set up the HP All-in-One with a shared voice/fax line
1.
Using the phone cord supplied in the box with the HP All-in-One, connect one end to your telephone wall jack, then connect the other end to the port labeled 1-LINE on the back of the HP All-in-One.
NOTE:
If you do not use the supplied cord to connect from the telephone wall jack to the HP All-in-One, you might not be able to fax successfully. This special phone cord is different from the phone cords you might already have in your home or office.
2.
Now you need to decide how you want the HP All-in-One to answer calls, automatically or manually:
• If you set up the HP All-in-One to answer calls automatically, it answers all incoming calls and receives faxes. The HP All-in-One will not be able to distinguish between fax and voice calls in this case; if you suspect the call is a voice call, you will need to answer it before the HP All-in-One answers the call.
To set up the HP All-in-One to answer calls automatically, turn on the Auto
Answer setting.
• If you set up the HP All-in-One to answer faxes manually, you must be available to respond in person to incoming fax calls or the HP All-in-One cannot receive faxes. To set up the HP All-in-One to answer calls manually, turn off the Auto
Answer setting.
Fax setup 33
Chapter 4
3.
Now you need to decide how you want the HP All-in-One to answer calls, automatically or manually:
• If you set up the HP All-in-One to answer calls automatically, it answers all incoming calls and receives faxes. The HP All-in-One will not be able to distinguish between fax and voice calls in this case; if you suspect the call is a voice call, you will need to answer it before the HP All-in-One answers the call.
To set up the HP All-in-One to answer calls automatically, turn on the Auto
Answer setting. For more information, see Set the answer mode .
• If you set up the HP All-in-One to answer faxes manually, you must be available to respond in person to incoming fax calls or the HP All-in-One cannot receive faxes. To set up the HP All-in-One to answer calls manually, turn off the Auto
Answer setting. For more information, see Set the answer mode .
4.
Run a fax test.
5.
Plug your phone into the telephone wall jack.
6.
Do one of the following, depending on your phone system:
• If you have a parallel-type phone system, remove the white plug from the port labeled 2-EXT on the back of the HP All-in-One, and then connect a phone to this port.
• If you have a serial-type phone system, you might plug your phone directly on top of the HP All-in-One cable which has a wall plug attached to it.
If you pick up the phone before the HP All-in-One answers the call and hear fax tones from a sending fax machine, you will need to answer the fax call manually.
Case F: Shared voice/fax line with voice mail
If you receive both voice calls and fax calls at the same phone number, and you also subscribe to a voice mail service through your telephone company, set up the HP All-in-
One as described in this section.
NOTE:
You cannot receive faxes automatically if you have a voice mail service at the same phone number you use for fax calls. You must receive faxes manually; this means you must be available to respond in person to incoming fax calls. If you want to receive faxes automatically instead, contact your telephone company to subscribe to a distinctive ring service, or to obtain a separate phone line for faxing.
34 Finish setting up the HP All-in-One
Figure 4-5 Back view of the HP All-in-One
1 Telephone wall jack
2 Use the phone cord supplied in the box with the HP All-in-One to connect to the "1-LINE" port
To set up the HP All-in-One with voice mail
1.
Using the phone cord supplied in the box with the HP All-in-One, connect one end to your telephone wall jack, then connect the other end to the port labeled 1-LINE on the back of the HP All-in-One.
NOTE:
If you do not use the supplied cord to connect from the telephone wall jack to the HP All-in-One, you might not be able to fax successfully. This special phone cord is different from the phone cords you might already have in your home or office.
2.
Turn off the Auto Answer setting.
3.
Run a fax test.
You must be available to respond in person to incoming fax calls, or the HP All-in-One cannot receive faxes.
Case G: Fax line shared with computer dial-up modem (no voice calls received)
If you have a fax line on which you receive no voice calls, and you also have a computer dial-up modem connected on this line, set up the HP All-in-One as described in this section.
Since your computer dial-up modem shares the phone line with the HP All-in-One, you will not be able to use both your modem and the HP All-in-One simultaneously. For
Fax setup 35
Chapter 4 example, you cannot use the HP All-in-One for faxing if you are using your computer dialup modem to send an e-mail or access the Internet.
Figure 4-6 Back view of the HP All-in-One
1 Telephone wall jack
2 Use the phone cord supplied in the box with the HP All-in-One to connect to the "1-LINE" port
3 Computer with modem
To set up the HP All-in-One with a computer dial-up modem
1.
Remove the white plug from the port labeled 2-EXT on the back of the HP All-in-One.
2.
Find the phone cord that connects from the back of your computer (your computer dial-up modem) to a telephone wall jack. Disconnect the cord from the telephone wall jack and plug it into the port labeled 2-EXT on the back of the HP All-in-One.
3.
Using the phone cord supplied in the box with the HP All-in-One, connect one end to your telephone wall jack, then connect the other end to the port labeled 1-LINE on the back of the HP All-in-One.
NOTE:
If you do not use the supplied cord to connect from the telephone wall jack to the HP All-in-One, you might not be able to fax successfully. This special phone cord is different from the phone cords you might already have in your home or office.
4.
If your modem software is set to receive faxes to your computer automatically, turn off that setting.
NOTE:
If you do not turn off the automatic fax reception setting in your modem software, the HP All-in-One will not be able to receive faxes.
5.
Turn on the Auto Answer setting.
6.
(Optional) Change the Rings to Answer setting to the lowest setting (two rings).
7.
Run a fax test.
When the phone rings, the HP All-in-One will answer automatically after the number of rings you set in the Rings to Answer setting. Then it will begin emitting fax reception tones to the sending fax machine and receive the fax.
36 Finish setting up the HP All-in-One
Case H: Shared voice/fax line with computer dial-up modem
If you receive both voice calls and fax calls at the same phone number, and you also have a computer dial-up modem connected on this phone line, set up the HP All-in-One as described in this section.
Since your computer dial-up modem shares the phone line with the HP All-in-One, you will not be able to use both your modem and the HP All-in-One simultaneously. For example, you cannot use the HP All-in-One for faxing if you are using your computer dialup modem to send an e-mail or access the Internet.
There are two different ways to set up the HP All-in-One with your computer based on the number of phone ports on your computer. Before you begin, check your computer to see if it has one or two phone ports.
• If your computer has only one phone port, you will need to purchase a parallel splitter
(also called a coupler), as shown below. (A parallel splitter has one RJ-11 port on the front and two RJ-11 ports on the back. Do not use a 2-line phone splitter, a serial splitter, or a parallel splitter which has two RJ-11 ports on the front and a plug on the back.)
Figure 4-7 Example of a parallel splitter
Fax setup 37
Chapter 4
• If your computer has two phone ports, set up the HP All-in-One as described below.
Figure 4-8 Back view of the HP All-in-One
1 Telephone wall jack
2 "IN" phone port on your computer
3 "OUT" phone port on your computer
4 Telephone
5 Computer with modem
6 Use the phone cord supplied in the box with the HP All-in-One to connect to the "1-LINE" port
To set up the HP All-in-One on the same phone line as a computer with two phone ports
1.
Remove the white plug from the port labeled 2-EXT on the back of the HP All-in-One.
2.
Find the phone cord that connects from the back of your computer (your computer dial-up modem) to a telephone wall jack. Disconnect the cord from the telephone wall jack and plug it into the port labeled 2-EXT on the back of the HP All-in-One.
3.
Connect a phone to the "OUT" port on the back of your computer dial-up modem.
4.
Using the phone cord supplied in the box with the HP All-in-One, connect one end to your telephone wall jack, then connect the other end to the port labeled 1-LINE on the back of the HP All-in-One.
NOTE:
If you do not use the supplied cord to connect from the telephone wall jack to the HP All-in-One, you might not be able to fax successfully. This special phone cord is different from the phone cords you might already have in your home or office.
5.
If your modem software is set to receive faxes to your computer automatically, turn off that setting.
NOTE:
If you do not turn off the automatic fax reception setting in your modem software, the HP All-in-One will not be able to receive faxes.
38 Finish setting up the HP All-in-One
6.
Now you need to decide how you want the HP All-in-One to answer calls, automatically or manually:
• If you set up the HP All-in-One to answer calls automatically, it answers all incoming calls and receives faxes. The HP All-in-One will not be able to distinguish between fax and voice calls in this case; if you suspect the call is a voice call, you will need to answer it before the HP All-in-One answers the call.
To set up the HP All-in-One to answer calls automatically, turn on the Auto
Answer setting.
• If you set up the HP All-in-One to answer faxes manually, you must be available to respond in person to incoming fax calls or the HP All-in-One cannot receive faxes. To set up the HP All-in-One to answer calls manually, turn off the Auto
Answer setting.
7.
Run a fax test.
If you pick up the phone before the HP All-in-One answers the call and hear fax tones from a sending fax machine, you will need to answer the fax call manually.
Case I: Shared voice/fax line with answering machine
If you receive both voice calls and fax calls at the same phone number, and you also have an answering machine that answers voice calls at this phone number, set up the HP Allin-One as described in this section.
Figure 4-9 Back view of the HP All-in-One
1 Telephone wall jack
2 "IN" port on your answering machine
3 "OUT" port on your answering machine
4 Telephone (optional)
5 Answering machine
6 Use the phone cord supplied in the box with the HP All-in-One to connect to the "1-LINE" port
Fax setup 39
Chapter 4
To set up the HP All-in-One with a shared voice/fax line with answering machine
1.
Remove the white plug from the port labeled 2-EXT on the back of the HP All-in-One.
2.
Unplug your answering machine from the telephone wall jack, and connect it to the port labeled 2-EXT on the back of the HP All-in-One.
NOTE:
If you do not connect your answering machine directly to the HP All-in-
One, fax tones from a sending fax machine might be recorded on your answering machine, and you probably will not be able to receive faxes with the HP All-in-
One.
3.
Using the phone cord supplied in the box with the HP All-in-One, connect one end to your telephone wall jack, then connect the other end to the port labeled 1-LINE on the back of the HP All-in-One.
NOTE:
If you do not use the supplied cord to connect from the telephone wall jack to the HP All-in-One, you might not be able to fax successfully. This special phone cord is different from the phone cords you might already have in your home or office.
4.
(Optional) If your answering machine does not have a built-in phone, for convenience you might want to connect a phone to the back of your answering machine at the
"OUT" port.
NOTE:
If your answering machine does not let you connect an external phone, you can purchase and use a parallel splitter (also known as a coupler) to connect both the answering machine and telephone to the HP All-in-One. You can use standard phone cords for these connections.
5.
Turn on the Auto Answer setting.
6.
Set your answering machine to answer after a low number of rings.
7.
Change the Rings to Answer setting on the HP All-in-One to the maximum number of rings supported by your device. (The maximum number of rings varies by country/ region.)
8.
Run a fax test.
When the phone rings, your answering machine will answer after the number of rings you have set, and then play your recorded greeting. The HP All-in-One monitors the call during this time, "listening" for fax tones. If incoming fax tones are detected, the HP All-in-One will emit fax reception tones and receive the fax; if there are no fax tones, the HP All-in-
One stops monitoring the line and your answering machine can record a voice message.
Case J: Shared voice/fax line with computer dial-up modem and answering machine
If you receive both voice calls and fax calls at the same phone number, and you also have a computer dial-up modem and answering machine connected on this phone line, set up the HP All-in-One as described in this section.
Since your computer dial-up modem shares the phone line with the HP All-in-One, you will not be able to use both your modem and the HP All-in-One simultaneously. For example, you cannot use the HP All-in-One for faxing if you are using your computer dialup modem to send an e-mail or access the Internet.
40 Finish setting up the HP All-in-One
There are two different ways to set the HP All-in-One with your computer based on the number of phone ports on your computer. Before you begin, check your computer to see if it has one or two phone ports.
• If your computer has only one phone port, you will need to purchase a parallel splitter
(also called a coupler), as shown below. (A parallel splitter has one RJ-11 port on the front and two RJ-11 ports on the back. Do not use a 2-line phone splitter, a serial splitter, or a parallel splitter which has two RJ-11 ports on the front and a plug on the back.)
Figure 4-10 Example of a parallel splitter
• If your computer has two phone ports, set up the HP All-in-One as described below.
Figure 4-11 Back view of the HP All-in-One
1 Telephone wall jack
2 "IN" phone port on your computer
3 "OUT" phone port on your computer
4 Telephone (optional)
5 Answering machine
6 Computer with modem
7 Use the phone cord supplied in the box with the HP All-in-One to connect to the "1-LINE" port
Fax setup 41
Chapter 4
To set up the HP All-in-One on the same phone line as a computer with two phone ports
1.
Remove the white plug from the port labeled 2-EXT on the back of the HP All-in-One.
2.
Find the phone cord that connects from the back of your computer (your computer dial-up modem) to a telephone wall jack. Disconnect the cord from the telephone wall jack and plug it into the port labeled 2-EXT on the back of the HP All-in-One.
3.
Unplug your answering machine from the telephone wall jack, and connect it to the
“OUT” port on the back of your computer modem.
This allows a direct connection between the HP All-in-One and your answering machine, even though the computer modem is connected first in line.
NOTE:
If you do not connect your answering machine in this way, fax tones from a sending fax machine might be recorded on your answering machine, and you might not be able to receive faxes with the HP All-in-One.
4.
Using the phone cord supplied in the box with the HP All-in-One, connect one end to your telephone wall jack, then connect the other end to the port labeled 1-LINE on the back of the HP All-in-One.
NOTE:
If you do not use the supplied cord to connect from the telephone wall jack to the HP All-in-One, you might not be able to fax successfully. This special phone cord is different from the phone cords you might already have in your home or office.
5.
(Optional) If your answering machine does not have a built-in phone, for convenience you might want to connect a phone to the back of your answering machine at the
"OUT" port.
NOTE:
If your answering machine does not let you connect an external phone, you can purchase and use a parallel splitter (also known as a coupler) to connect both the answering machine and telephone to the HP All-in-One. You can use standard phone cords for these connections.
6.
If your modem software is set to receive faxes to your computer automatically, turn off that setting.
NOTE:
If you do not turn off the automatic fax reception setting in your modem software, the HP All-in-One will not be able to receive faxes.
7.
Turn on the Auto Answer setting.
8.
Set your answering machine to answer after a low number of rings.
9.
Change the Rings to Answer setting on the HP All-in-One to the maximum number of rings supported by your device. (The maximum number of rings varies by country/ region.)
10.
Run a fax test.
When the phone rings, your answering machine will answer after the number of rings you have set, and then play your recorded greeting. The HP All-in-One monitors the call during this time, "listening" for fax tones. If incoming fax tones are detected, the HP All-in-One will emit fax reception tones and receive the fax; if there are no fax tones, the HP All-in-
One stops monitoring the line and your answering machine can record a voice message.
42 Finish setting up the HP All-in-One
Case K: Shared voice/fax line with computer dial-up modem and voice mail
If you receive both voice calls and fax calls at the same phone number, use a computer dial-up modem on the same phone line, and subscribe to a voice mail service through your telephone company, set up the HP All-in-One as described in this section.
NOTE:
You cannot receive faxes automatically if you have a voice mail service at the same phone number you use for fax calls. You must receive faxes manually; this means you must be available to respond in person to incoming fax calls. If you want to receive faxes automatically instead, contact your telephone company to subscribe to a distinctive ring service, or to obtain a separate phone line for faxing.
Since your computer dial-up modem shares the phone line with the HP All-in-One, you will not be able to use both your modem and the HP All-in-One simultaneously. For example, you cannot use the HP All-in-One for faxing if you are using your computer dialup modem to send an e-mail or access the Internet.
There are two different ways to set up the HP All-in-One with your computer based on the number of phone ports on your computer. Before you begin, check your computer to see if it has one or two phone ports.
• If your computer has only one phone port, you will need to purchase a parallel splitter
(also called a coupler), as shown below. (A parallel splitter has one RJ-11 port on the front and two RJ-11 ports on the back. Do not use a 2-line phone splitter, a serial splitter, or a parallel splitter which has two RJ-11 ports on the front and a plug on the back.)
Figure 4-12 Example of a parallel splitter
Fax setup 43
Chapter 4
• If your computer has two phone ports, set up the HP All-in-One as described below.
44
Figure 4-13 Back view of the HP All-in-One
1 Telephone wall jack
2 "IN" phone port on your computer
3 "OUT" phone port on your computer
4 Telephone
5 Computer with modem
6 Use the phone cord supplied in the box with the HP All-in-One to connect to the "1-LINE" port
To set up the HP All-in-One on the same phone line as a computer with two phone ports
1.
Remove the white plug from the port labeled 2-EXT on the back of the HP All-in-One.
2.
Find the phone cord that connects from the back of your computer (your computer dial-up modem) to a telephone wall jack. Disconnect the cord from the telephone wall jack and plug it into the port labeled 2-EXT on the back of the HP All-in-One.
3.
Connect a phone to the "OUT" port on the back of your computer dial-up modem.
4.
Using the phone cord supplied in the box with the HP All-in-One, connect one end to your telephone wall jack, then connect the other end to the port labeled 1-LINE on the back of the HP All-in-One.
NOTE:
If you do not use the supplied cord to connect from the telephone wall jack to the HP All-in-One, you might not be able to fax successfully. This special phone cord is different from the phone cords you might already have in your home or office.
5.
If your modem software is set to receive faxes to your computer automatically, turn off that setting.
NOTE:
If you do not turn off the automatic fax reception setting in your modem software, the HP All-in-One will not be able to receive faxes.
6.
Turn off the Auto Answer setting.
7.
Run a fax test.
You must be available to respond in person to incoming fax calls, or the HP All-in-One cannot receive faxes.
Finish setting up the HP All-in-One
Change settings on the HP All-in-One to receive faxes
In order to receive faxes successfully, you might need to change some settings on the
HP All-in-One. If you are unsure which setting to choose for a specific fax option, refer to the detailed fax setup instructions provided in the printed documentation.
This section contains the following topics:
•
Choose the recommended answer mode for your setup
•
•
Set the number of rings before answering
•
Change the answer ring pattern for distinctive ringing
Choose the recommended answer mode for your setup
Refer to the table below to determine how you should answer incoming fax calls based on your home or office setup. From the first column in the table, choose the type of equipment and services applicable to your office setup. Then, look up the appropriate setting in the second column. The third column describes how the HP All-in-One answers incoming calls.
After you have determined the recommended answer mode setting for your home or office
setup, see Set the answer mode
for more information.
Equipment/services sharing your fax line
None.
(You have a separate phone line on which you receive only fax calls.)
A shared voice and fax line and no answering machine.
(You have a shared phone line in which you receive both voice and fax calls.)
Off
Recommended
Auto Answer setting
On
Voice mail service provided by your telephone company.
An answering machine and a shared voice and fax line.
Off
On
Description
The HP All-in-One automatically answers all incoming calls using the Rings to Answer setting.
The HP All-in-One will not automatically answer calls.
You must press Start Fax Black or Start Fax Color to receive a fax.
You might use this setting if the majority of calls on this phone line are voice calls and you rarely receive faxes.
The HP All-in-One will not automatically answer calls.
You must press Start Fax Black or Start Fax Color to receive a fax.
The HP All-in-One will not automatically answer calls.
Instead, the HP All-in-One will monitor the line when the call is answered by a person or by the answering machine. If the HP All-in-One detects fax tones on the line, the HP All-in-One receives the fax. If the answering machine answers a voice call, the answering machine records the incoming message.
In addition to the Auto Answer setting, set the number of rings to answer on the HP All-in-One to a greater number of rings than the answering machine.
You want the answering machine to answer before the
HP All-in-One.
Fax setup 45
Chapter 4
(continued)
Equipment/services sharing your fax line
Distinctive ringing service.
Recommended
Auto Answer setting
On
Description
The HP All-in-One automatically answers all incoming calls. Make sure the ring pattern the phone company set for your fax line matches the Distinctive Ring setting on the HP All-in-One.
Related topics
•
Set the number of rings before answering
•
•
Change the answer ring pattern for distinctive ringing
Set the answer mode
The answer mode determines whether the HP All-in-One answers incoming calls or not.
• Turn on the Auto Answer setting if you want the HP All-in-One to answer faxes
automatically. The HP All-in-One will answer all incoming calls and faxes.
• Turn off the Auto Answer setting if you want to receive faxes manually. You must be available to respond in person to the incoming fax call or the HP All-in-One will not receive faxes.
To set the answer mode
1.
Press Setup.
2.
Press 4, and then press 2.
This selects Basic Fax Setup and then selects Rings to Answer.
3.
Enter the appropriate number of rings by using the keypad, or press or to change the number of rings.
4.
Press OK to accept the setting.
Related topics
•
•
Choose the recommended answer mode for your setup
Set the number of rings before answering
If you turn on the Auto Answer setting, you can specify how many rings should occur before the HP All-in-One automatically answers the incoming call.
The Rings to Answer setting is important if you have an answering machine on the same phone line as the HP All-in-One, because you want the answering machine to answer the phone before the HP All-in-One does. The number of rings to answer for the HP Allin-One should be greater than the number of rings to answer for the answering machine.
For example, set your answering machine to a low number of rings and the HP All-in-One to answer in the maximum number of rings. (The maximum number of rings varies by country/region.) In this setup, the answering machine will answer the call and the HP Allin-One will monitor the line. If the HP All-in-One detects fax tones, the HP All-in-One will receive the fax. If the call is a voice call, the answering machine will record the incoming message.
46 Finish setting up the HP All-in-One
To set the number of rings before answering from the control panel
1.
Press Setup.
2.
Press 4, and then press 3.
This selects Basic Fax Setup and then selects Rings to Answer.
3.
Enter the appropriate number of rings by using the keypad, or press or to change the number of rings.
4.
Press OK to accept the setting.
Related topics
Change the answer ring pattern for distinctive ringing
Many phone companies offer a distinctive ringing feature that allows you to have several phone numbers on one phone line. When you subscribe to this service, each number will have a different ring pattern. You can set up the HP All-in-One to answer incoming calls that have a specific ring pattern.
If you connect the HP All-in-One to a line with distinctive ringing, have your telephone company assign one ring pattern to voice calls and another ring pattern to fax calls. HP recommends that you request double or triple rings for a fax number. When the HP Allin-One detects the specified ring pattern, it will answer the call and receive the fax.
If you do not have a distinctive ring service, use the default ring pattern, which is All
Rings.
To change the distinctive ring pattern from the control panel
1.
Verify that the HP All-in-One is set to answer fax calls automatically.
2.
Press Setup.
3.
Press 5, and then press 1.
This selects Advanced Fax Setup and then selects Distinctive Ring.
4.
Press to select an option, and then press OK.
When the phone rings with the ring pattern assigned to your fax line, the HP All-in-
One answers the call and receives the fax.
Related topics
Test your fax setup
You can test your fax setup to check the status of the HP All-in-One and to make sure it is set up properly for faxing. Perform this test after you have completed setting up the
HP All-in-One for faxing. The test does the following:
• Tests the fax hardware
• Verifies the correct type of phone cord is connected to the HP All-in-One
• Checks that the phone cord is plugged into the correct port
• Checks for a dial tone
Fax setup 47
Chapter 4
• Checks for an active phone line
• Tests the status of your phone line connection
The HP All-in-One prints a report with the results of the test. If the test fails, review the report for information on how to fix the problem and rerun the test.
To test your fax setup from the control panel
1.
Set up the HP All-in-One for faxing according to your particular home or office setup instructions.
2.
Insert the print cartridges and load full-size paper in the input tray before starting the test.
3.
Press Setup.
4.
Press 6, then press 6 again.
This selects the Tools menu and then selects Run Fax Test.
The HP All-in-One displays the status of the test on the display and prints a report.
5.
Review the report.
• If the test passes and you are still having problems faxing, check the fax settings listed in the report to verify the settings are correct. A blank or incorrect fax setting can cause problems faxing.
• If the test fails, review the report for more information on how to fix any problems found.
6.
After you pick up the fax report from the HP All-in-One, press OK.
If necessary, resolve any problems found and rerun the test.
Set the fax header
The fax header prints your name and fax number on the top of every fax you send. HP recommends that you set up the fax header by using the software that you installed with the HP All-in-One. You can also set up the fax header from the control panel, as described here.
NOTE:
In some countries/regions the fax header information is a legal requirement.
To set a default fax header from the control panel
1.
Press Setup.
2.
Press 4, and then press 1.
This selects Basic Fax Setup and then selects Fax Header.
3.
Enter your personal or company name, and then press OK.
4.
Enter your fax number by using the numeric keypad, and then press OK.
To set a default fax header from the HP Photosmart Studio (Mac) Software
1.
Select the HP Device Manager from the Dock.
The HP Device Manager window appears.
2.
In the Information and Settings pop-up menu, choose Fax Setup Utility.
The Device Settings dialog box opens.
3.
From the pop-up menu, choose Fax General.
48 Finish setting up the HP All-in-One
4.
In the Fax Header area, type your company name and fax number.
NOTE:
The information you enter in the Personal Information area is used when you send a cover page. This information is not included in the fax header information.
5.
Click Apply or OK.
The fax header information will appear on all the faxes you send.
Related topics
Set up speed dialing
You can assign speed dial entries to fax numbers you use often. This lets you dial those numbers quickly by using the control panel.
This section contains the following topics:
•
Set up individual speed dial entries
•
Set up group speed dial entries
•
•
Set up individual speed dial entries
You can create speed dial entries for fax numbers that you use frequently. If necessary, you can also edit the name or fax number of a speed dial entry you have already created.
TIP:
You can include individual speed dial entries in a group speed dial entry. This enables you to send a fax to a group of people at one time. (The maximum number of individual speed dial entries allowed in a group speed dial entry varies by model.)
This section contains the following topics:
•
Create individual speed dial entries
•
Update individual speed dial entries
Create individual speed dial entries
You can create speed dial entries from the control panel or from your computer by using the software that you installed with the HP All-in-One.
To create speed dial entries from the control panel
1.
Press Setup.
2.
Press 3, and then press 1.
This selects Speed Dial Setup and then selects Individual Speed Dial.
The first unassigned speed dial entry appears on the display.
3.
Press OK to select the displayed speed dial entry. You can also press or to select an empty entry, and then press OK.
4.
Enter the fax number to assign to that entry, and then press OK.
Fax setup 49
Chapter 4
5.
Enter the name, and then press OK.
6.
Press 1 if you want to set up another number, or press 2 if you are finished creating speed dial entries.
To create speed dial entries from the HP Photosmart Studio (Mac) Software
1.
Select the HP Device Manager from the Dock.
The HP Device Manager window appears.
2.
In the Devices pop-up menu, choose the HP All-in-One.
3.
In the Information and Settings pop-up menu, choose Fax Speed Dial Settings.
4.
In the Fax Speed Dial dialog box, choose an empty number in the speed dial list.
5.
Click Add Individual.
The Add Individual dialog box appears.
6.
In the Name box, type the individual's name.
7.
In the Fax Number box, type the fax number.
8.
Click OK.
The name of the individual appears in the fax speed dial list.
9.
Click Apply or OK when you are finished creating speed dial entries.
Related topics
Update individual speed dial entries
You can edit the name or fax number in a speed dial entry from the control panel or from your computer by using the software that you installed with the HP All-in-One.
To update a speed dial entry from the control panel
1.
Press Setup.
2.
Press 3, and then press 1.
This selects Speed Dial Setup and then selects Individual Speed Dial.
3.
Press or to scroll through the speed dial entries, and then press OK to select the appropriate entry.
4.
When the current fax number appears, press to erase it.
5.
Enter the new fax number, and then press OK.
TIP:
To add a pause in the fax number you are entering, press Redial/Pause, or press the Symbols (*) button repeatedly, until a dash (-) appears on the display.
6.
Enter the new name, and then press OK.
7.
Press 1 to update another speed dial entry, or press 2 when you are finished.
To update a speed dial entry from the HP Photosmart Studio (Mac) Software
1.
Select the HP Device Manager from the Dock.
The HP Device Manager window appears.
2.
In the Information and Settings pop-up menu, choose Fax Speed Dial Settings.
50 Finish setting up the HP All-in-One
3.
In the Fax Speed Dial dialog box, choose the speed dial entry that you want to edit, and then click Edit Entry.
4.
Make your changes, and then click OK.
5.
Click Apply or OK when you are finished updating speed dial entries.
Related topics
Set up group speed dial entries
You can place individual speed dial entries that you have set up into groups, so that you can fax the same document to multiple recipients at once. (The maximum number of individual speed dial entries allowed in a group speed dial entry varies by model.)
NOTE:
The numbers you include in the group speed dial entry must already be set up as individual speed dial entries on the HP All-in-One.
To create group speed dial entries from the control panel
1.
Press Setup.
2.
Press 3, and then press 2.
This selects Speed Dial Setup and then selects Group Speed Dial.
The first unassigned speed dial entry appears on the display.
3.
Press OK to select the displayed speed dial entry. You can also press or to select an empty entry, and then press OK.
4.
Press or to scroll through the individual speed dial entries you set up, and then press OK to select the appropriate entry.
5.
Press 1 to add another individual speed dial entry, or press 2 if you are finished.
6.
Enter the group speed dial name, and then press OK.
7.
Press 1 to add another group, or press 2 if you are finished.
To create group speed dial entries from the HP Photosmart Studio (Mac) Software
1.
Select the HP Device Manager from the Dock.
The HP Device Manager window appears.
2.
In the Information and Settings pop-up menu, choose Fax Speed Dial Settings.
3.
In the Fax Speed Dial dialog box, choose an empty number in the speed dial list.
4.
Click Add Group.
The Add Speed Dial Group dialog box appears.
5.
In the Group Name box, enter the name.
6.
Choose the individual speed dial entry to add to the group, and then click Add to
Group.
7.
Click OK.
The name of the group appears in the fax speed dial list with an arrow icon next to it.
You can click the arrow to view the list of members in that group.
8.
Click Apply or OK when you are finished.
Fax setup 51
Chapter 4
Related topics
•
Set up individual speed dial entries
•
Delete speed dial entries
You can delete an individual or group speed dial entry. When deleting speed dial entries, consider the following:
• Deleting an individual speed dial entry also deletes that entry from any groups to which you have assigned it.
• Deleting a group speed dial entry does not delete the individual speed dial entries associated with it. You can still use the individual speed dial entries to send faxes.
To delete speed dial entries from the control panel
1.
Press Setup.
2.
Press 3, and then press 3 again.
This selects Speed Dial Setup and then selects Delete Speed Dial.
3.
Press or until the speed dial entry that you want to delete appears, and then press OK to delete it.
To delete speed dial entries from the HP Photosmart Studio (Mac) Software
1.
Select the HP Device Manager from the Dock.
The HP Device Manager window appears.
2.
In the Devices pop-up menu, choose the HP All-in-One.
3.
In the Information and Settings pop-up menu, choose Fax Speed Dial Settings.
4.
In the Fax Speed Dial dialog box, choose the speed dial entry that you want to delete, and then click Clear.
5.
Click OK.
6.
Click Apply or OK when you are finished deleting speed dial entries.
Print the speed dial list
You can print a list of all the speed dial entries that you programmed on the HP All-in-
One.
To print the speed dial list
1.
Press Setup.
2.
Press 3, and then press 4.
This selects Speed Dial Setup and then selects Print Speed Dial List.
TIP:
You can also print this list by selecting Speed Dial List from the Print
Report menu. Press Setup, press 2, and then press 7.
Set up the phone book
In addition to setting up speed dial entries for frequently used numbers, you can set up fax numbers in the Phone Book that came with your HP Photosmart Studio (Mac)
Software or in the Address Book that comes with Mac OS X. When you send a fax by
52 Finish setting up the HP All-in-One
using the HP Photosmart Studio (Mac) Software, you can simply select an entry from the Phone Book or Address Book and the contact information is automatically inserted.
HP recommends using the Address Book to store your fax recipients' information, rather than the Phone Book. For information on adding recipients to the Address Book, see the onscreen Help that came with Mac OS X.
NOTE:
The Phone Book and Address Book are only available when sending a fax from the HP Photosmart Studio (Mac) Software. Speed dial entries are available when sending a fax from both the HP Photosmart Studio (Mac) Software and the control panel of the HP All-in-One.
This section contains the following topics:
•
•
Edit or delete a phone book entry
•
Create a phone book entry
Follow these steps to add an entry to the phone book.
To create a phone book entry from the HP Photosmart Studio (Mac) Software
1.
Select the HP Device Manager from the Dock.
The HP Device Manager window appears.
2.
From the Information and Settings drop-down, select Fax Speed Dial Settings.
3.
From the pop-up menu, choose Fax Phone Book.
The Fax Phone Book dialog box opens.
4.
Click Add Individual, and then enter the fax number and other recipient information.
5.
Click OK.
The recipient is added to the Phone Book.
Edit or delete a phone book entry
Follow these steps to edit or delete an entry from the phone book.
To edit or delete a phone book entry from the HP Photosmart Studio (Mac) Software
1.
Select the HP Device Manager from the Dock.
The HP Device Manager window appears.
2.
From the Information and Settings drop-down, select Fax Speed Dial Settings.
3.
From the pop-up menu, choose Fax Phone Book.
The Fax Phone Book dialog box opens.
4.
Select the phone book entry you want to edit or delete.
• To edit the phone book entry, click Edit Entry, and then make the appropriate changes. Click OK.
• To delete the phone book entry, click Delete, and then click OK.
5.
Click Apply or OK.
Export and import fax numbers
If you would like to share your phone book with someone else, you can simply export it to a file, which can then be imported into another application. If you have names and fax
Fax setup 53
Chapter 4 numbers in external applications, and you can save them to a tab-delimited text file, you can import that file into the HP All-in-One phone book.
To export a phone book using the HP Photosmart Studio (Mac) Software
1.
In the HP Photosmart Studio task bar, click Devices.
The HP Device Manager window appears.
2.
In the Select Device area, click the icon for the HP All-in-One.
3.
In the Device Options area, click Settings, and then choose Fax Speed Dial
Settings.
4.
From the pop-up menu, choose Fax Phone Book.
5.
Click Export.
6.
Choose a name and location for the exported file, and then click Save.
The phone book is saved as a file in the location you specified.
7.
Click Apply or OK.
To import a phone book or text file from the HP Photosmart Studio (Mac) Software
1.
Select the HP Device Manager from the Dock.
The HP Device Manager window appears.
2.
From the Information and Settings drop-down, select Fax Speed Dial Settings.
3.
From the pop-up menu, choose Fax Phone Book.
4.
Click Import.
The Select Import Type dialog box appears.
5.
Select from one of the following:
• Import HP AiO phone book file: choose this option if you have access to an exported HP AiO phone book file.
• Import Tab Delimited Text File: choose this option if you have access to a tabdelimited text file that has been created from an external software program.
If you chose Import Tab Delimited Text File, identify the contents of the file by using the pull-down lists that follow.
6.
Click OK.
7.
Locate and select the file you want to import, and then click Open.
The phone book or external file is imported into your phone book and the entries appear in the phone book list.
54 Finish setting up the HP All-in-One
5 Load originals and load paper
You can load many different types and sizes of paper in the HP All-in-One, including letter or A4 paper, photo paper, transparencies, and envelopes.
This section contains the following topics:
•
•
•
•
Load originals
You can load an original for a copy, fax, or scan job in the automatic document feeder or on the glass. Originals that are loaded in the automatic document feeder will automatically be fed into the HP All-in-One.
This section contains the following topics:
•
Load an original in the automatic document feeder
•
Load an original in the automatic document feeder
You can copy, scan, or fax a single- or multiple-page letter-, A4- (up to 35 pages of plain paper), or legal-size document (up to 20 sheets of plain paper) by placing it in the document feeder tray.
CAUTION:
Do not load photos in the automatic document feeder; this might cause damage to your photos.
NOTE:
Some features, such as the Fit to Page copy feature, do not work when you load your originals in the automatic document feeder. You must load your originals on the glass.
To load an original in the document feeder tray
1.
Load your original, with the print side up, into the document feeder tray. Slide the paper into the automatic document feeder until you hear a beep or see a message on the display indicating that the HP All-in-One detected the pages you loaded.
TIP:
For more help on loading originals in the automatic document feeder, refer to the diagram engraved in the document feeder tray.
Load originals and load paper 55
Chapter 5
2.
Slide the paper guides inward until they stop at the left and right edges of the paper.
NOTE:
Remove all originals from the document feeder tray before lifting the lid on the HP All-in-One.
Related topics
Load an original on the glass
You can copy, scan, or fax up to letter- or A4-size originals by loading them on the glass.
If your original is legal-size or contains multiple full-size pages, load it in the automatic document feeder.
NOTE:
Many of the special features will not work correctly if the glass and lid backing are not clean.
To load an original on the scanner glass
1.
Remove all originals from the document feeder tray, and then lift the lid on the HP Allin-One.
2.
Load your original print side down on the right front corner of the glass.
56 Load originals and load paper
3.
Close the lid.
Related topics
•
Load an original in the automatic document feeder
•
Select print media
The device is designed to work well with most types of office media. It is best to test a variety of print media types before buying large quantities. Use HP media for optimum print quality. Visit the HP Web site at www.hp.com
for more information about HP media.
•
Tips for selecting and using print media
•
Understand specifications for supported media
•
•
Tips for selecting and using print media
For the best results, observe the following guidelines.
• Always use media that conforms to the device specifications. For more information,
see Understand specifications for supported media
.
• Load only one type of media at a time into a tray.
• For Tray 1 and Tray 2, load media print-side down and aligned against the right and back edges of the tray. Tray 2 is available with some models. For more information,
see Understand supported media types and weights .
• Tray 2 is designed to hold only plain paper.
•
Do not overload the trays. For more information, see Understand specifications for supported media
.
• To prevent jams, poor print quality, and other printing problems, avoid the following media:
• Multipart forms
• Media that is damaged, curled, or wrinkled
• Media with cutouts or perforations
• Media that is heavily textured, embossed, or does not accept ink well
• Media that is too lightweight or stretches easily
Cards and envelopes
• Avoid envelopes that have a very slick finish, self-stick adhesives, clasps, or windows.
Also avoid cards and envelopes with thick, irregular, or curled edges, or areas that are wrinkled, torn, or otherwise damaged.
• Use tightly constructed envelopes, and make sure the folds are sharply creased.
• Load envelopes with the flaps facing up.
Select print media 57
Chapter 5
Photo media
• Use the Best mode to print photographs. Note that in this mode, printing takes longer and more memory is required from your computer.
• Remove each sheet as it prints and set it aside to dry. Allowing wet media to stack up may cause smearing.
Transparencies
• Insert transparencies with the rough side down and the adhesive strip pointing towards the back of the device.
• Use the Normal mode to print transparencies. This mode provides longer drying time and ensures that the ink dries completely before the next page is delivered to the output tray.
• Remove each sheet as it prints and set it aside to dry. Allowing wet media to stack up may cause smearing.
Custom-sized media
• Use only custom-sized media that is supported by the device.
• If your application supports custom-sized media, set the media size in the application before printing the document. If not, set the size in the print driver. You might need to reformat existing documents to print them correctly on custom-sized media.
Understand specifications for supported media
Use the
Understand supported sizes and
what features will work with your media.
•
•
Understand supported media types and weights
Understand supported sizes
Media size
Standard media sizes
U.S. Letter (216 x 279 mm; 8.5 x 11 inches)
U.S. Legal (216 x 356 mm; 8.5 x 14 inches)
A4 (210 x 297 mm; 8.3 x 11.7 inches)
U.S. Executive (184 x 267 mm; 7.25 x
10.5 inches)
B5 (182 x 257 mm; 7.17 x 10.12 inches)
Tray 1
A5 (148 x 210 mm; 5.8 x 8.3 inches)
Duplexer ADF
58 Load originals and load paper
(continued)
Media size
Borderless A4 (210 x 297 mm; 8.3 x 11.7
inches)*
Borderless A5 (148 x 210 mm; 5.8 x 8.3
inches)*
Borderless B5 (182 x 257 mm; 7.17 x
10.12 inches)*
Envelopes
U.S. #10 Envelope (105 x 241 mm; 4.12
x 9.5 inches)*
A2 Envelope (111 x 146 mm; 4.37 x 5.75
inches)*
DL Envelope (110 x 220 mm; 4.3 x 8.7
inches)*
C6 Envelope (114 x 162 mm; 4.5 x 6.4
inches)*
Japanese Envelope Chou #2 (119 x 277 mm; 4.7 x 10.9 inches)*
Japanese Envelope Chou #3 (120 x 235 mm; 4.7 x 9.3 inches)*
Japanese Envelope Chou #4 (90 x 205 mm; 3.5 x 8.1 inches)*
Cards
Index card (76.2 x 127 mm; 3 x 5 inches)
*
Index card (102 x 152 mm; 4 x 6 inches)
*
Index card (127 x 203 mm; 5 x 8 inches)
*
A6 card (105 x 148.5 mm; 4.13 x 5.83
inches)*
Borderless A6 card (105 x 148.5 mm;
4.13 x 5.83 inches)*
Hagaki** (100 x 148 mm; 3.9 x 5.8
inches)*
Ofuku Hagaki** (200 x 148 mm; 7.9 x 5.8
inches)*
Photo media
Photo media (102 x 152 mm; 4 x 6 inches)*
Photo media (5 x 7 inches)*
Tray 1 Duplexer ADF
Select print media 59
Chapter 5
(continued)
Media size
Photo media (8 x 10 inches)*
Photo media (10 x 20 cm)*
Photo media (4 x 8 inches)*
Photo media HV*
Photo media cabinet (165 x 120 mm; 6.5
x 4.7 inches)*
Photo media 2L (178 x 127 mm; 7 x 5 inches)*
Photo media (13 x 18 cm)*
Photo media B7 (88 x 125 mm; 3.5 x 4.9
inches)*
Photo L (89 x 127 mm; 3.5 x 5 inches)*
Borderless photo media (102 x 152 mm;
4 x 6 inches)*
Borderless photo media (10 x 20 cm)*
Borderless photo media (4 x 8inches)*
Borderless HV*
Borderless cabinet (165 x 120 mm; 6.5 x
4.7 inches)*
Borderless 2L (178 x 127 mm; 7 x 5 inches)*
Borderless photo media (5 x 7 inches)*
Borderless photo media (8 x 10 inches)
*
Borderless photo media (8.5 x 11 inches)*
Borderless photo media (13 x 18 cm)*
Borderless B7 (88 x 125 mm; 3.5 x 4.9
inches)*
Borderless hagaki (100 x 148mm)*
Borderless Photo L (89 x 127 mm; 3.5 x
5 inches)*
Other media
Custom-sized media between 76.2 to
216 mm wide and 127 to 594 mm long
Tray 1 Duplexer
60 Load originals and load paper
ADF
(continued)
Media size
(3 to 8.5 inches wide and 5 to 23 inches long) *
Custom-sized media (ADF) between
127 to 216 mm wide and 241 to 305 mm long (5 to 8.5 inches wide and 9.5 to 12 inches long)
Panorama (4 x 10 inches, 4 x 11 inches,
4 x 12 inches, and double A4) *
Borderless panorama (4 x 10 inches, 4 x
11 inches, 4 x 12 inches, and double A4)
*
Tray 1 Duplexer ADF
* Not compatible for use with the ADF for single- or double-sided printing
** The device is compatible with plain and inkjet hagaki from Japan Post only. It is not compatible with photo hagaki from Japan Post.
Understand supported media types and weights
Tray
Tray 1
Type
Paper
Weight
60 to 105 g/m 2
(16 to 28 lb bond)
Duplexer
Transparencies
Photo media
Labels
Envelopes
Cards
Paper
Output-bin All supported media
280 g/m 2
(75 lb bond)
75 to 90 g/m 2
(20 to 24 lb bond envelope)
Up to 200 g/m 2
(110 lb index)
60 to 105 g/m 2
(16 to 28 lb bond)
Capacity
Up to 250 sheets of plain paper
(25 mm or 1 inch stacked)
Up to 70 sheets
(17 mm or 0.67 inch stacked)
Up to 100 sheets
(17 mm or 0.67 inch stacked)
Up to 100 sheets
(17 mm or 0.67 inch stacked)
Up to 30 sheets
(17 mm or 0.67 inch stacked)
Up to 80 cards
Not applicable
Up to 150 sheets of plain paper (text printing)
Select print media 61
Chapter 5
Set minimum margins
The document margins must match (or exceed) these margin settings in portrait orientation.
Media
U.S. Letter
U.S. Legal
A4
Photo media
U.S. Executive
B5
A5
Cards
Envelopes
(1) Left margin
2 mm (0.12
inch)
2 mm (0.12
inch)
(2) Right margin
2 mm (0.12
inch)
2 mm (0.12
inch)
(3) Top margin
1.8 mm (0.07
inch)
(4) Bottom margin*
2 mm (0.12
inch)
1.8 mm (0.07
inch)
6 mm (0.24
inch)
3.3 mm (0.13
inch)
3.3 mm (0.13
inch)
16.5 mm (0.65
inch)
16.5 mm
(0.65 inch)
* To achieve this margin setting on a computer running Windows, click the Advanced tab in the print driver, and select Minimize Margins.
NOTE:
If you are using the duplexer (available with some models), the minimum top and bottom margins must match or exceed 12 mm (0.47 inch).
Papers to avoid
Using paper that is too thin or too thick, paper that has a slick texture, or paper that stretches easily can cause paper jams. Using paper that has a heavy texture or does not accept ink can cause printed images to smear, bleed, or not fill in completely.
Papers to avoid for all print and copy jobs
• Any size paper other than those listed in the technical specifications. For more information, see
• Paper with cutouts or perforations (unless specifically designed for use with HP inkjet devices).
62 Load originals and load paper
• Highly textured stock, such as linen. It might not print evenly, and the ink can bleed into these papers.
• Extremely smooth, shiny, or coated papers not specifically designed for the HP Allin-One. They can jam the HP All-in-One or repel the ink.
• Multi-part forms, such as duplicate and triplicate forms. They can wrinkle or get stuck, and the ink is more likely to smear.
• Envelopes with clasps or windows. They can get stuck in the rollers and cause paper jams.
• Banner paper.
Additional papers to avoid when copying
• Envelopes.
• Transparency film other than HP Premium Inkjet Transparency Film or HP Premium
Plus Inkjet Transparency Film.
• Iron-On Transfers.
• Greeting card paper.
Load paper
This section describes the procedure for loading different types and sizes of paper into the HP All-in-One for your copies, printouts, or faxes.
TIP:
To help prevent rips, wrinkles, and curled or bent edges, store all paper flat in a resealable bag. If the paper is not stored properly, extreme changes in temperature and humidity might result in curled paper that does not work well in the HP All-in-One.
This section contains the following topics:
•
•
Load 10 x 15 cm (4 x 6 inch) photo paper
•
•
Load full-size paper
You can load many types of letter, A4, or legal paper into the input tray of the HP All-in-
One.
Load paper 63
Chapter 5
To load full-size paper
1.
Remove the output tray.
2.
Slide the paper-width guide to its outermost position.
3.
Tap a stack of paper on a flat surface to align the edges, and then check the paper for the following:
• Make sure it is free of rips, dust, wrinkles, and curled or bent edges.
• Make sure all the paper in the stack is the same size and type.
64 Load originals and load paper
4.
Insert the stack of paper into the input tray with the short edge forward and the print side down. Slide the stack of paper forward until it stops.
CAUTION:
Make sure that the HP All-in-One is idle and silent when you load paper into the input tray. If the HP All-in-One is servicing the print cartridges or otherwise engaged in a task, the paper stop inside the device might not be in place. You could push the paper too far forward, causing the HP All-in-One to eject blank pages.
TIP:
If you are using letterhead, insert the top of the page first with the print side down. For more help on loading full-size paper and letterhead, refer to the diagram engraved in the base of the input tray.
5.
Slide the paper-width guide inward until it stops at the edge of the paper.
Do not overload the input tray; make sure the stack of paper fits within the input tray and is no higher than the top of the paper-width guide.
6.
Replace the output tray.
Load paper 65
Chapter 5
7.
Flip the tray extender up toward you.
NOTE:
When you use legal-size paper, leave the tray extender closed.
Load 10 x 15 cm (4 x 6 inch) photo paper
You can load 10 x 15 cm (4 x 6 inch) photo paper into the input tray of the HP All-in-One.
For the best results, use 10 x 15 cm (4 x 6 inch) HP Premium Plus Photo Paper or HP
Premium Photo Paper.
TIP:
To help prevent rips, wrinkles, and curled or bent edges, store all paper flat in a resealable bag. If the paper is not stored properly, extreme changes in temperature and humidity might result in curled paper that does not work well in the HP All-in-One.
For best results, set the paper type and paper size before copying or printing.
To load 10 x 15 cm ( 4 x 6 inch) photo paper with tab in the input tray
1.
Remove the output tray.
2.
Remove all paper from the input tray.
3.
Insert the stack of photo paper into the far-right side of the input tray with the short edge forward and the print side down. Slide the stack of photo paper forward until it stops.
Load the photo paper so that the tabs are closest to you.
TIP:
For more help on loading small-size photo paper, refer to the guides engraved in the base of the input tray for loading photo paper.
66 Load originals and load paper
4.
Slide the paper-width guide inward against the photo paper until it stops.
Do not overload the input tray; make sure the stack of paper fits within the input tray and is no higher than the top of the paper-width guide.
5.
Replace the output tray.
Related topics
•
Understand specifications for supported media
•
Load index cards
You can load index cards into the input tray of the HP All-in-One to print notes, recipes, and other text.
For best results, set the paper type and paper size before copying or printing.
To load index cards in the input tray
1.
Remove the output tray.
2.
Remove all paper from the input tray.
3.
Insert the stack of cards, print side down, into the far-right side of the input tray. Slide the stack of cards forward until it stops.
4.
Slide the paper-width guide inward against the stack of cards until it stops.
Do not overload the input tray; make sure the stack of cards fits within the input tray and is no higher than the top of the paper-width guide.
5.
Replace the output tray.
Load paper 67
Chapter 5
Related topics
•
Load 10 x 15 cm (4 x 6 inch) photo paper
•
Load envelopes
You can load one or more envelopes into the input tray of the HP All-in-One. Do not use shiny or embossed envelopes or envelopes that have clasps or windows.
NOTE:
For specific details on how to format text for printing on envelopes, consult the help files in your word processing software. For best results, consider using a label for the return address on envelopes.
To load envelopes
1.
Remove the output tray.
2.
Remove all paper from the input tray.
3.
Insert one or more envelopes into the far-right side of the input tray with the envelope flaps up and on the left. Slide the stack of envelopes forward until it stops.
TIP:
For more help on loading envelopes, refer to the diagram engraved in the base of the input tray.
4.
Slide the paper-width guide inward against the stack of envelopes until it stops.
Do not overload the input tray; make sure the stack of envelopes fits within the input tray and is not higher than the top of the paper-width guide.
5.
Replace the output tray.
Avoid paper jams
To help avoid paper jams, follow these guidelines.
• Remove printed papers from the output tray frequently.
• Prevent curled or wrinkled paper by storing all unused paper flat in a resealable bag.
• Ensure that paper loaded in the input tray lays flat and the edges are not bent or torn.
• Do not combine different paper types and paper sizes in the input tray; the entire stack of paper in the input tray must be the same size and type.
68 Load originals and load paper
• Adjust the paper-width guide in the input tray to fit snugly against all paper. Make sure the paper-width guide does not bend the paper in the input tray.
• Do not force paper too far forward in the input tray.
• Use paper types that are recommended for the HP All-in-One. For more information,
see Understand specifications for supported media
.
• Do not leave originals on the glass. If you load an original in the automatic document feeder while there is already an original on the glass, the original can jam in the automatic document feeder.
Avoid paper jams 69
Chapter 5
70 Load originals and load paper
6 Print from your computer
The HP All-in-One can be used with any software application that allows printing. You can print a range of projects, such as borderless images, newsletters, greeting cards, iron-on transfers, and posters.
This section contains the following topics:
•
Print from a software application
•
•
Print from a software application
Most print settings are automatically handled by the software application. You need to change the settings manually only when you change print quality, print on specific types of paper or transparency film, or use special features.
To print from a software application
1.
Make sure you have paper loaded in the input tray.
2.
From the File menu in your software application, choose Page Setup.
The Page Setup dialog box appears, allowing you to specify the paper size, orientation, and scaling.
3.
Make sure the HP All-in-One is the selected printer.
4.
Specify the page attributes:
• Choose the paper size.
• Select the orientation.
• Enter the scaling percentage.
5.
Click OK.
6.
From the File menu in your software application, choose Print.
The Print dialog box appears, and the Copies & Pages panel opens.
7.
Change the print settings for each option in the pop-up menu, as appropriate for your project.
NOTE:
When printing a photo, you must select options for the correct paper type and photo enhancement.
8.
Click Print to begin printing.
Change the print settings
You can customize the print settings of the HP All-in-One to handle nearly any print task.
•
Mac users
Use the Page Setup and Print dialog boxes to change the settings for your print job.
Which dialog box you use depends on which setting you want to change.
Print from your computer 71
Chapter 6
To change the paper size, orientation, or scaling percentage
1.
From the File menu in your software application, choose Page Setup.
2.
Make sure the HP All-in-One is the selected printer.
3.
Make changes to the paper size, orientation, and scaling percentage settings, and click OK.
To change all other print settings
1.
From the File menu in your software application, choose Print.
2.
Make sure the HP All-in-One is the selected printer.
3.
Click Copies and Pages to view the full list of print options. Make changes to the print settings, and click Print to print the job.
Stop a print job
Although you can stop a print job from either the HP All-in-One or the computer, HP recommends you stop it from the HP All-in-One for best results.
To stop a print job from the HP All-in-One
▲ Press Cancel on the control panel. If the print job does not stop, press Cancel again.
It can take a few moments for printing to be cancelled.
72 Print from your computer
7 Use the copy features
The HP All-in-One enables you to produce high-quality color and black-and-white copies on a variety of paper types, including transparencies. You can enlarge or reduce the size of an original to fit a specific paper size, adjust the darkness of the copy, and use special features to make high-quality copies of photos, including borderless copies.
TIP:
For the best copy performance on standard copy projects, set the paper size to Letter or A4, the paper type to Plain Paper, and the copy quality to Fast.
This section contains the following topics:
•
•
•
•
•
•
•
Make a 10 x 15 cm (4 x 6 inch) borderless copy of a photo
•
Resize an original to fit onto letter or A4 paper
•
Resize an original using custom settings
•
Copy a legal-size document onto letter paper
•
Adjust the lightness and darkness of your copy
•
Enhance blurred areas of your copy
•
Enhance light areas of your copy
•
Make a copy
You can make quality copies from the control panel. Load multiple-page originals into the document feeder tray.
To make a copy from the control panel
1.
Make sure you have paper loaded in the input tray.
2.
Load your original print side down on the right front corner of the glass or print side up in the document feeder tray.
If you use the document feeder tray, place the pages so that the top edge of the document goes in first.
3.
Do one of the following:
• Press Start Copy Black to initiate a black-and-white copy job.
• Press Start Copy Color to initiate a color copy job.
NOTE:
If you have a color original, pressing Start Copy Black produces a blackand-white copy of the color original, while pressing Start Copy Color produces a full-color copy of the color original.
Use the copy features 73
Chapter 7
Set the number of copies
You can set the number of copies that you want to print by using the Number of
Copies option.
To set the number of copies from the control panel
1.
Make sure you have paper loaded in the input tray.
2.
Load your original print side down on the right front corner of the glass or print side up in the document feeder tray.
If you use the document feeder tray, place the pages so that the top edge of the document goes in first.
3.
In the Copy area, press Menu repeatedly until Number of Copies appears.
4.
Press or use the keypad to enter the number of copies, up to the maximum.
(The maximum number of copies varies by model.)
TIP:
If you hold down either of the arrow buttons, the number of copies changes by increments of 5 to make it easier to set a large number of copies.
5.
Press Start Copy Black or Start Copy Color.
To set the number of copies from the HP Photosmart Studio (Mac) Software
1.
Make sure you have paper loaded in the input tray.
2.
Load your original print side down on the right front corner of the glass or print side up in the document feeder tray.
If you use the document feeder tray, place the pages so that the top edge of the document goes in first.
3.
Select the HP Device Manager from the Dock.
The HP Device Manager window appears.
4.
In the Tasks menu, double-click Make Copies.
The HP Copy dialog box appears.
5.
In the Number of Copies box, type or select the number of copies, up to the maximum.
(The maximum number of copies varies by model.)
6.
Click Black Copy or Color Copy.
Set the copy paper size
You can set the paper size on the HP All-in-One. The paper size you select should match what is loaded in your input tray.
To set the paper size from the control panel
1.
In the Copy area, press Menu repeatedly until Copy Paper Size appears.
2.
Press until the appropriate paper size appears.
3.
Press Start Copy Black or Start Copy Color.
74 Use the copy features
To set the paper size from the HP Photosmart Studio (Mac) Software
1.
Select the HP Device Manager from the Dock.
The HP Device Manager window appears.
2.
In the Tasks area, double-click Make Copies.
The HP Copy dialog box appears.
3.
From the Paper Size pop-up menu, choose the paper size.
Set the copy paper type
You can set the paper type on the HP All-in-One.
To set the paper type for copies
1.
In the Copy area, press Menu repeatedly until Paper Type appears.
2.
Press until the appropriate paper type appears.
3.
Press Start Copy Black or Start Copy Color.
To set the paper type from the HP Photosmart Studio (Mac) Software
1.
Select the HP Device Manager from the Dock.
The HP Device Manager window appears.
2.
In the Tasks area, double-click Make Copies.
The HP Copy dialog box appears.
3.
From the Paper Type pop-up menu, choose the paper type.
Refer to the following table to determine which paper type setting to choose based on the paper loaded in the input tray.
Paper type Control panel setting
Copier paper or letterhead
HP Bright White Paper
HP Premium Plus Photo Paper, Glossy
HP Premium Plus Photo Paper, Matte
Plain Paper
Plain Paper
Premium Photo
Premium Photo
HP Premium Plus 10 x 15 cm (4 x 6 inch) Photo Paper Premium Photo
HP Premium or Premium Plus Inkjet Transparency Film Transparency
Other transparency film
Plain Hagaki
Transparency
Plain Paper
Glossy Hagaki
L (Japan only)
Premium photo
Premium Photo
Set the copy paper type 75
Chapter 7
Change copy speed or quality
The HP All-in-One provides three options that affect copy speed and quality:
• Best produces the highest quality for all paper and eliminates the banding (striping) effect that sometimes occurs in solid areas. Best copies slower than the other quality settings.
• Normal delivers high-quality output and is the recommended setting for most of your copying. Normal copies faster than Best and is the default setting.
• Fast copies faster than the Normal setting. The text is comparable to the quality of the Normal setting, but the graphics might be lower quality. The Fast setting uses less ink and extends the life of your print cartridges.
To change the copy quality
1.
Make sure you have paper loaded in the input tray.
2.
Load your original print side down on the right front corner of the glass or print side up in the document feeder tray.
If you use the document feeder tray, place the pages so that the top edge of the document goes in first.
3.
In the Copy area, press Quality until the appropriate quality setting is lit.
4.
Press Start Copy Black or Start Copy Color.
To change the copy quality from the HP Photosmart Studio (Mac) Software
1.
Make sure you have paper loaded in the input tray.
2.
Load your original print side down on the right front corner of the glass or print side up in the document feeder tray.
If you use the document feeder tray, place the pages so that the top edge of the document goes in first.
3.
Select the HP Device Manager from the Dock.
The HP Device Manager window appears.
4.
In the Devices pop-up menu, choose the HP All-in-One, and then double-click Make
Copies.
The HP Copy dialog box appears.
5.
In the Copy Quality area, select Best, Normal, or Fast.
See above for complete descriptions.
6.
Click Black Copy or Color Copy.
Change default copy settings
When you change copy settings from the control panel, the settings apply only to the current copy job. To apply copy settings to all future copy jobs, you can save the settings as defaults.
To set default copy settings from the control panel
1.
Make any needed changes to the Copy settings.
2.
In the Copy area, press Menu repeatedly until Set New Defaults appears.
3.
Press until Yes appears.
76 Use the copy features
NOTE:
The settings you specify here are only saved on the HP All-in-One. They do not adjust the settings in the software. You can save your most frequently used settings by using the software that you installed with the HP All-in-One.
To set default copy settings from the HP Photosmart Studio (Mac) Software
1.
Select the HP Device Manager from the Dock.
The HP Device Manager window appears.
2.
In the Devices pop-up menu, choose the HP All-in-One, and then double-click Make
Copies.
The HP Copy dialog box appears.
3.
Change any applicable settings.
4.
Click Save as Default to save your changes.
The default settings that you set by using this dialog box apply only to copy jobs initiated from your Mac.
NOTE:
The paper size defaults to letter or A4, depending on the country/region you selected when you set up your device.
Make a 10 x 15 cm (4 x 6 inch) borderless copy of a photo
For the best quality when copying a photo, load photo paper in the input tray and change your copy settings for the correct paper type and photo enhancement. You might also want to use the photo print cartridge for superior print quality. With the tri-color and photo print cartridges installed, you have a six-ink system.
To make a borderless copy of a photo from the control panel
1.
Load 10 x 15 cm (4 x 6 inch) photo paper in the input tray.
2.
Load your original photo print side down on the right front corner of the glass.
Position the photo on the glass so the long edge of the photo is along the front edge of the glass, as indicated by the engraved guides along the edge of the glass.
Make a 10 x 15 cm (4 x 6 inch) borderless copy of a photo 77
Chapter 7
3.
Press Start Copy Black or Start Copy Color.
The HP All-in-One makes a 10 x 15 cm (4 x 6 inch) borderless copy of your original photo.
NOTE:
If you loaded tabbed paper in the photo tray, you can remove the tab from the copy of your photo once the ink has completely dried.
TIP:
If the output is not borderless set the paper type to Premium Photo, and then try making the copy again.
To make a borderless copy of a photo from the HP Photosmart Studio (Mac)
Software
1.
Load 10 x 15 cm (4 x 6 inch) photo paper into the photo tray.
TIP:
When making borderless copies, you must have photo paper (or other specialty paper) loaded.
2.
Load your original print side down on the right front corner of the glass.
3.
In the HP Photosmart Studio (Mac) task bar, click Devices.
The HP Device Manager window appears.
4.
Select the HP Device Manager from the Dock.
The HP Device Manager window appears.
5.
Click Make Copies.
6.
In the Tasks area, double-click Make Copies.
The HP Copy dialog box appears.
7.
From the Paper Size pop-up menu, choose the 10 x 15 cm (4 x 6 inch) paper size option.
8.
From the Paper Type pop-up menu, choose the type of photo paper you loaded in the input tray.
78 Use the copy features
9.
Make any other changes to the settings you want.
10.
Click Black Copy or Color Copy.
The HP All-in-One makes a 10 x 15 cm (4 x 6 inch) borderless copy of your original photo.
NOTE:
You can remove the tab once the ink has completely dried.
Related topics
•
Load 10 x 15 cm (4 x 6 inch) photo paper
•
•
Resize an original to fit onto letter or A4 paper
If the image or text on your original fills the entire sheet with no margins, use Fit to
Page or Full Page 91% to reduce your original and prevent unwanted cropping of the text or images at the edges of the sheet.
TIP:
You can also use Fit to Page to enlarge a small photo to fit within the printable area of a full-size page. In order to do this without changing the proportions of the original or cropping the edges, the HP All-in-One might leave an uneven amount of white space around the edges of the paper.
To resize a document from the control panel
1.
Make sure you have paper loaded in the input tray.
2.
Load your original print side down on the right front corner of the glass or print side up in the document feeder tray.
If you use the document feeder tray, place the pages so that the top edge of the document goes in first.
3.
In the Copy area, press the Reduce/Enlarge button.
Resize an original to fit onto letter or A4 paper 79
Chapter 7
4.
Do one of the following:
• If you loaded your original in the document feeder tray or on the glass, press
until Full Page 91% appears.
• If you loaded a full- or small-size original on the glass, press until Fit to Page appears.
5.
Press Start Copy Black or Start Copy Color.
To resize a document from the HP Photosmart Studio (Mac) Software
1.
Make sure you have paper loaded in the input tray.
2.
Load your original.
3.
Select the HP Device Manager from the Dock.
The HP Device Manager window appears.
4.
In the Tasks area, double-click Make Copies.
The HP Copy dialog box appears.
5.
In the Reduce-Enlarge area, select Fit to Page.
6.
Click Black Copy or Color Copy.
Resize an original using custom settings
You can use your own custom settings to reduce or enlarge a copy of a document.
To set a custom size from the control panel
1.
Make sure you have paper loaded in the input tray.
2.
Load your original print side down on the right front corner of the glass.
If you use the document feeder tray, place the pages so that the top edge of the document goes in first.
3.
In the Copy area, press the Reduce/Enlarge button.
4.
Press until Custom 100% appears.
5.
Press OK.
6.
Press or use the keypad to enter a percentage to reduce or enlarge the copy.
(The minimum and maximum percentage to resize a copy varies by model.)
7.
Press Start Copy Black or Start Copy Color.
To set a custom size from the HP Photosmart Studio (Mac) Software
1.
Make sure you have paper loaded in the input tray.
2.
Load your original.
3.
Select the HP Device Manager from the Dock.
The HP Device Manager window appears.
4.
In the Tasks area, double-click Make Copies.
The HP Copy dialog box appears.
5.
In the Reduce-Enlarge area, select Custom, and then enter a percentage.
6.
Click Black Copy or Color Copy.
80 Use the copy features
Copy a legal-size document onto letter paper
You can use the Legal > Ltr 72% setting to reduce a copy of a legal-size document to a size that fits onto letter paper.
NOTE:
The percentage in the example, Legal > Ltr 72%, might not match the percentage that appears in the display.
To copy a legal-size document onto letter paper
1.
Make sure you have paper loaded in the input tray.
2.
Load your legal-size document print side up in the document feeder tray.
Place the page in the document feeder tray so that the top edge of the document goes in first.
3.
In the Copy area, press the Reduce / Enlarge button.
4.
Press until Legal > Ltr 72% appears.
5.
Press Start Copy Black or Start Copy Color.
Adjust the lightness and darkness of your copy
You can use the Lighter / Darker option to adjust the contrast of the copies you make.
To adjust the copy contrast from the control panel
1.
Make sure you have paper loaded in the input tray.
2.
Load your original print side down on the right front corner of the glass or print side up in the document feeder tray.
If you use the document feeder tray, place the pages so that the top edge of the document goes in first.
3.
In the Copy area, press Menu repeatedly until Lighter / Darker appears.
4.
Do one of the following:
• Press to darken the copy.
• Press to lighten the copy.
5.
Press Start Copy Black or Start Copy Color.
Copy a legal-size document onto letter paper 81
Chapter 7
To adjust the copy contrast from the HP Photosmart Studio (Mac) Software
1.
Make sure you have paper loaded in the input tray.
2.
Load your original print side down on the right front corner of the glass or print side up in the document feeder tray.
If you use the document feeder tray, place the pages so that the top edge of the document goes in first.
3.
Select the HP Device Manager. from the Dock.
4.
In the Tasks area, double-click Make Copies.
The HP Copy dialog box appears.
5.
In the Copy Quality area, drag the Contrast slider to the right to darken.
NOTE:
You can also drag the slider to the left to lighten the copy.
6.
Click Black Copy or Color Copy.
Enhance blurred areas of your copy
You can use the Enhancements feature to adjust the quality of text documents by sharpening edges of black text or adjust photographs by enhancing light colors that might otherwise appear white.
The Mixed enhancement is the default option. Use the Mixed enhancement to sharpen edges of most originals.
To copy a blurred document from the control panel
1.
Make sure you have paper loaded in the input tray.
2.
Position the photo on the glass so the long edge of the photo is along the front edge of the glass.
Load your original print side down on the right front corner of the glass or print side up in the document feeder tray.
3.
In the Copy area, press Menu repeatedly until Enhancements appears.
4.
Press until the Text setting appears.
5.
Press Start Copy Black or Start Copy Color.
If any of the following occur, turn off Text enhancement by selecting Photo or None:
• Stray dots of color surround some text on your copies
• Large, black typefaces look splotchy (not smooth)
• Thin, colored objects or lines contain black sections
• Horizontal grainy or white bands appear in light- to medium-gray areas
Enhance light areas of your copy
You can use Photo enhancements to enhance light colors that might otherwise appear white. You can also use Photo enhancements to eliminate or reduce any of the following that might occur when copying with Text enhancements:
• Stray dots of color surround some text on your copies
• Large, black typefaces look splotchy (not smooth)
82 Use the copy features
• Thin, colored objects or lines contain black sections
• Horizontal grainy or white bands appear in light- to medium-gray areas
To copy an overexposed photo
1.
Make sure you have paper loaded in the input tray.
2.
Load your original photo print side down on the right front corner of the glass.
Position the photo on the glass so the long edge of the photo is along the front edge of the glass.
3.
In the Copy area, press Menu repeatedly until Enhancements appears.
4.
Press until the Photo enhancement setting appears.
5.
Press Start Copy Color.
Stop copying
To stop copying
▲ Press Cancel on the control panel.
Stop copying 83
Chapter 7
84 Use the copy features
8 Use the scan features
Scanning is the process of converting text and pictures into an electronic format for your computer. You can scan almost anything (photos, magazine articles and text documents), as long as you are careful not to scratch the glass on the HP All-in-One.
You can use the scanning features of the HP All-in-One to do the following:
• Scan text from an article into your word processor and quote it in a report.
• Print business cards and brochures by scanning a logo and using it in your publishing software.
• Send photos to friends and relatives by scanning your favorite prints and including them in e-mail messages.
• Create a photographic inventory of your house or office.
• Archive treasured photos in an electronic scrapbook.
This section contains the following topics:
•
•
•
•
Scan an image
You can start a scan from your computer or from the HP All-in-One.
To use the scan features, the HP All-in-One and computer must be connected and turned on. The HP All-in-One software must also be installed and running on your computer prior to scanning. On a Mac, the HP All-in-One software is always running.
This section contains the following topics:
•
Scan an original to a computer
•
Scan an original to a computer
You can scan originals placed either on the glass or in the document feeder tray by using the control panel.
To scan to a computer
1.
Load your original print side down on the right front corner of the glass or print side up in the document feeder tray.
2.
Press Scan To. A list of destinations, including software applications, appears on the display.
Use the scan features 85
Chapter 8
3.
Press OK to select the default application to receive the scan, or press to select a different application, and then press OK.
A preview image of the scan appears on your computer, where you can edit it.
4.
Make any edits to the preview image, and then click Accept when you are finished.
The HP All-in-One sends the scan to the selected application.
Stop scanning
To stop scanning
▲ Press Cancel on the control panel.
Edit a scanned preview image
You can use the tools in the HP Scan Pro window to modify a preview image. Any changes that you make, such as brightness, image type, resolution, and more, apply to this scan session only.
You can do the following using the HP Scan Pro software:
• Select a portion of the image
• Change the image type and quality
• Change the resolution
• Crop or straighten the image
• Adjust the brightness or contrast
• Adjust the color or saturation
• Sharpen or blur the image
• Rotate the image
• Resize the image
For more information, see the HP Scan Pro section of the HP Photosmart Mac Help.
Print a scanned image
You can print a scanned image from the HP Scan Pro scan preview software. For more information, see the HP Scan Pro section of the HP Photosmart Mac Help.
Change default scan settings
You can use the tools in the software you installed with the HP All-in-One to permanently change certain settings for all scan sessions.
You can also use your favorite application as the default destination for viewing scanned images. You can change the default destination application associated with the Scan button in the software you installed with the HP All-in-One, and the Scan To button on the control panel.
This section contains the following topics:
•
Add a new image save destination
•
Change the default destination
86 Use the scan features
•
Change an image save destination
•
Change resolution or image type
•
•
Change the image preview setting
Add a new image save destination
The software you installed with the HP All-in-One enables you to add new applications to the list of possible destinations for your scans. When you add an application, it appears in the list where you select an application as the scan destination in the HP Scan Pro window. You can add different types of new applications, such as software for photo editing, e-mail, and OCR.
To add a new application to the picture-editing or e-mail destination list
1.
In the HP Photosmart Studio task bar, click Devices.
The HP Device Manager window appears.
2.
In the Devices pop-up menu, choose the HP All-in-One.
3.
In the Information and Settings pop-up menu, choose Scan Preferences.
The HP ScanTo Destination dialog box opens.
4.
Click New.
The Create Scan Destination dialog box opens.
5.
Select Picture Editing Application or Email Application.
6.
Click Next.
7.
Type a name for the scan destination.
8.
Select the application from the list or click Browse and find the application.
9.
Select the document format from the pop-up menu.
10.
Click Finish.
To add a new application to the text/OCR destination list
1.
Select the HP Device Manager from the Dock.
The HP Device Manager window appears.
2.
In the Devices pop-up menu, choose the HP All-in-One.
3.
In the Information and Settings pop-up menu, choose Scan Preferences.
The HP ScanTo Destination dialog box opens.
4.
Click New.
The Create Scan Destination dialog box opens.
5.
Select Text Editing/OCR Application.
6.
Click Next.
7.
Type a name for the scan destination.
8.
Select the application from the list or click Browse and find the application.
The Automatic mode check box is selected by default. In this mode, the Readiris
OCR software automatically converts the image to text and sends it to the text editor, where you can edit the text and save it. The layout and formatting of your original are retained in the text editor application as much as possible.
If Automatic mode is not selected, the scan remains in the Readiris OCR window, where you can manipulate it before converting or sending it.
Change default scan settings 87
Chapter 8
9.
(Optional) Deselect Automatic mode if you want to manipulate the scanned document in the Readiris OCR software before converting it to text or sending it to the text editor application.
10.
Click Finish.
Change the default destination
You can change the default destination for scans by using the software you installed with the HP All-in-One.
To change the default destination
1.
In the HP Photosmart Studio task bar, click Devices.
The HP Device Manager window appears.
2.
In the Devices pop-up menu, choose the HP All-in-One.
3.
In the Information and Settings pop-up menu, choose Scan Preferences.
The HP ScanTo Destination dialog box opens.
4.
In the Custom Scan Settings area, do one of the following:
• Click Scan Picture Settings to change settings for the default destination associated with the Scan Picture button.
• Click Scan Document Settings to change settings for the default destination associated with the Scan Document button.
• Click Front Panel Scan Settings to change settings for the default destination associated with the Start Scan button on the control panel of the HP All-in-One.
The Custom Scan Settings dialog box opens.
5.
Select the desired default destination from the Send To pop-up menu.
6.
Click OK.
Change an image save destination
You can change certain settings for an existing destination: the name of the destination, the destination application, or the document format.
To edit the properties of a destination
1.
In the HP Photosmart Studio task bar, click Devices.
The HP Device Manager window appears.
2.
In the Devices pop-up menu, choose the HP All-in-One.
3.
In the Information and Settings pop-up menu, choose Scan Preferences.
The HP ScanTo Destination dialog box opens.
4.
In the Destinations Displayed area, select the destination and click Edit.
The Edit Scan Destination dialog box opens.
5.
Do one or more of the following:
• Change the name of the destination.
• Select a different destination from the list.
• Select a different document format from the pop-up menu.
6.
Click Finish.
88 Use the scan features
Change resolution or image type
You might want to permanently change the resolution or image type of an existing destination.
To change the resolution or image type
1.
In the HP Photosmart Studio task bar, click Devices.
The HP Device Manager window appears.
2.
In the Devices pop-up menu, choose the HP All-in-One.
3.
In the Information and Settings pop-up menu, choose Scan Preferences.
The HP ScanTo Destination dialog box opens.
4.
In the Custom Scan Settings area, do one of the following:
• Click Scan Picture Settings to change settings for the default destination associated with the Scan Picture button.
• Click Scan Document Settings to change settings for the default destination associated with the Scan Document button.
• Click Front Panel Scan Settings to change settings for the default destination associated with the Start Scan button on the control panel of the HP All-in-One.
The Custom Scan Settings dialog box opens.
5.
Do one or more of the following:
• Select a different resolution from the pop-up menu.
• Select a different image type from the pop-up menu.
6.
Click OK.
Change Text Editing/OCR mode
You can preview and manipulate your scanned document in your OCR software before the software automatically converts the image to text and sends it to the destination. For example, you might want to delete a portion of the text. You can toggle the automatic mode by editing the Text/OCR Destination in the HP Photosmart Studio.
To turn off automatic mode in a text/OCR destination
1.
Select the HP Device Manager from the Dock.
The HP Device Manager window appears.
2.
In the Devices pop-up menu, choose the HP All-in-One.
3.
In the Information and Settings pop-up menu, choose Scan Preferences.
The HP ScanTo Destination dialog box opens.
4.
In the Destinations Displayed area, select the destination and click Edit.
The Edit Scan Destination dialog box opens.
5.
Select Text Editing/OCR Application.
6.
Click Edit.
The Edit Scan Destination dialog box opens.
7.
Deselect Automatic mode.
8.
Click Finish.
Change default scan settings 89
Chapter 8
Change the image preview setting
You can set the scan software to automatically send a scan to the default destination without making any changes in the HP Scan Pro window.
To skip the preview
1.
Select the HP Device Manager from the Dock.
The HP Device Manager window appears.
2.
In the Devices pop-up menu, choose the HP All-in-One.
3.
In the Information and Settings pop-up menu, choose Scan Preferences.
The HP ScanTo Destination dialog box opens.
4.
In the Custom Scan Settings area, do one of the following:
• Click Scan Picture Settings to change settings for the default destination associated with the Scan Picture button.
• Click Scan Document Settings to change settings for the default destination associated with the Scan Document button.
• Click Control Panel Scan Settings to change settings for the default destination associated with the Start Scan button on the control panel of the HP All-in-One.
The Custom Scan Settings dialog box opens.
5.
Select Skip Scan Preview Window.
6.
Click OK.
90 Use the scan features
9 Use the fax features
You can use the HP All-in-One to send and receive faxes, including color faxes. You can set up speed dial entries to send faxes quickly and easily to frequently used numbers.
From the control panel, you can also set a number of fax options, such as resolution and the contrast between lightness/darkness on the faxes you send.
NOTE:
Before you begin faxing, make sure you have set up the HP All-in-One properly for faxing. You might have already done this as part of the initial setup, by using either the control panel or the software that came with the HP All-in-One.
You can verify the fax is set up correctly by running the fax setup test from the control panel. You can access this test from the Setup menu.
This section contains the following topics:
•
•
•
•
Fax over the Internet using IP phone
•
•
Send a fax
You can send a fax in a variety of ways. Using the control panel, you can send a blackand-white or color fax from the HP All-in-One. You can also send a fax manually by dialing from an attached phone. This allows you to speak with the recipient before sending the fax.
This section contains the following topics:
•
•
•
Send a fax manually from a phone
•
Send a fax using monitor dialing
•
•
•
Send a fax to multiple recipients
•
Send a color original or photo fax
•
•
Change the fax resolution and Lighter / Darker settings
•
Send a fax in Error Correction Mode
Send a basic fax
You can easily send a single- or multiple-page black-and-white fax by using the control panel, as described here.
Use the fax features 91
Chapter 9
NOTE:
If you need printed confirmation that your faxes were successfully sent, enable fax confirmation before sending any faxes.
TIP:
You can also send a fax manually by dialing from a phone or by using the monitor dialing feature from the control panel. These features allow you to control the pace of your dialing. They are also useful when you want to use a calling card to charge the call and you need to respond to tone prompts while dialing.
To send a basic fax from the control panel
1.
Load your originals print side up into the document feeder tray. If you are sending a single-page fax, such as a photograph, you can also load your original print side down on the glass.
NOTE:
If you are sending a multiple-page fax, you must load the originals in the document feeder tray. You cannot fax a multiple-page document from the glass.
2.
Enter the fax number by using the keypad, press Speed Dial or a one-touch speed dial button to select a speed dial, or press Redial/Pause to redial the last number dialed.
TIP:
To add a pause in the fax number you are entering, press Redial/Pause, or press the Symbols (*) button repeatedly, until a dash (-) appears on the display.
3.
Press Start Fax Black.
• If the device detects an original loaded in the automatic document feeder, the HP All-in-One sends the document to the number you entered.
•
If the device does not detect an original loaded in the automatic document
feeder, the Fax from glass? prompt appears. Make sure your original is loaded print side down on the glass, and then press 1 to select Yes.
TIP:
If the recipient reports issues with the quality of the fax you sent, you can try changing the resolution or contrast of your fax.
Related topics
•
Send a fax manually from a phone
•
Send a fax using monitor dialing
•
Change the fax resolution and Lighter / Darker settings
•
Print fax confirmation reports
•
Send a color original or photo fax
Send a fax using speed dials
You can quickly send a black-and-white or color fax from the HP All-in-One or your computer by using speed dials. From the control panel, you can press Speed Dial or a one-touch speed dial button to access your speed dial entries. The one-touch speed dial buttons correspond to the first five speed dial entries that you set up.
Speed dial entries will not appear until you have set them up.
92 Use the fax features
To send a fax using speed dials from the control panel
1.
Load your originals print side up into the document feeder tray. If you are sending a single-page fax, such as a photograph, you can also load your original print side down on the glass.
NOTE:
If you are sending a multiple-page fax, you must load the originals in the document feeder tray. You cannot fax a multiple-page document from the glass.
2.
Do one of the following:
• Press a one-touch speed dial button to access one of the first five speed dial entries.
• Press Speed Dial repeatedly, until the appropriate speed dial entry appears.
TIP:
You can also scroll through the speed dial entries by pressing or , or you can select a speed dial entry by entering its speed dial code using the keypad on the control panel.
3.
Press Start Fax Black or Start Fax Color.
• If the device detects an original loaded in the automatic document feeder, the HP All-in-One sends the document to the number you entered.
•
If the device does not detect an original loaded in the automatic document
feeder, the Fax from glass? prompt appears. Make sure your original is loaded on the glass, and then press 1 to select Yes.
To send a fax using speed dials from the HP Photosmart Studio (Mac) Software
1.
Load your originals print side up into the document feeder tray. If you are sending a single-page fax, such as a photograph, you can also load your original print side down on the glass.
2.
Select the HP Device Manager from the Dock.
The HP Device Manager window appears.
3.
From the Tasks menu, double-click Send Fax.
The Print dialog box opens.
4.
From the Printer pop-up menu, choose the HP All-in-One (Fax).
5.
From the pop-up menu, choose Fax Recipients.
6.
Click Open Speed Dials.
7.
Choose a speed dial entry from the list, and then click Add to Recipients.
8.
Click Done.
The speed dial entry appears in the Recipient List.
9.
Click Send Fax Now.
Related topics
Send a fax manually from a phone
You can initiate a fax call from a telephone on the same phone line as the HP All-in-One if you are more comfortable using the keypad on your phone, rather than using the keypad on the control panel of the HP All-in-One. This method of sending a fax is called manually sending a fax. When you send a fax manually, you can hear the dial tones, telephone
Send a fax 93
Chapter 9 prompts, or other sounds through the handset on your telephone. This makes it easy for you to use a calling card to send your fax.
Depending on how the recipient has their fax machine set up, the recipient might answer the phone, or the fax machine might take the call. If a person answers the phone, you can speak with the recipient before sending the fax. If a fax machine answers the call, you can send the fax directly to the fax machine when you hear the fax tones from the receiving fax machine.
To send a fax manually from a phone
1.
Load your originals print side up into the document feeder tray.
NOTE:
This feature is not supported if you load your originals on the glass. You must load your originals in the document feeder tray.
2.
Dial the number by using the keypad on the phone that is connected to the HP All-in-
One.
NOTE:
Do not use the keypad on the control panel of the HP All-in-One when manually sending a fax. You must use the keypad on your phone to dial the recipient's number.
3.
If the recipient answers the telephone, you can engage in a conversation before sending your fax.
NOTE:
If a fax machine answers the call, you will hear fax tones from the receiving fax machine. Proceed to the next step to transmit the fax.
4.
Once you are ready to send the fax, press Start Fax Black or Start Fax Color.
NOTE:
If prompted, press 1 to select Send Fax, and then press Start Fax
Black or Start Fax Color again.
If you were speaking with the recipient before sending the fax, inform the recipient that they should press Start on their fax machine after they hear fax tones.
The telephone line is silent while the fax is transmitting. At this point, you can hang up the telephone. If you want to continue speaking with the recipient, remain on the line until the fax transmission is complete.
Send a fax using monitor dialing
Monitor dialing allows you to dial a number from the control panel as you would dial a regular telephone. When you send a fax using monitor dialing, you can hear the dial tones, telephone prompts, or other sounds through the speakers on the HP All-in-One. This enables you to respond to prompts while dialing, as well as control the pace of your dialing.
TIP:
If you do not enter your calling card PIN fast enough, the HP All-in-One might start sending fax tones too soon and cause your PIN not to be recognized by the calling card service. If this is the case, you can create a speed dial entry to store the
PIN for your calling card.
NOTE:
Make sure the volume is turned on, or you will not hear a dial tone.
94 Use the fax features
To send a fax using monitor dialing from the control panel
1.
Load your originals print side up into the document feeder tray. If you are sending a single-page fax, such as a photograph, you can also load your original print side down on the glass.
NOTE:
If you are sending a multiple-page fax, you must load the originals in the document feeder tray. You cannot fax a multiple-page document from the glass.
2.
Press Start Fax Black or Start Fax Color.
• If the device detects an original loaded in the automatic document feeder, you will hear a dial tone.
•
If the device does not detect an original loaded in the automatic document
feeder, the Fax from glass? prompt appears. Make sure your original is loaded on the glass, and then press 1 to select Yes.
3.
Once you hear the dial tone, enter the number by using the keypad on the control panel.
4.
Follow any prompts that might occur.
TIP:
If you are using a calling card to send a fax and you have your calling card
PIN stored as a speed dial, when prompted to enter your PIN, press Speed
Dial or a one-touch speed dial button to select the speed dial entry where you have your PIN stored.
Your fax is sent when the receiving fax machine answers.
Related topics
•
•
Send a fax from memory
You can scan a black-and-white fax into memory and then send the fax from memory.
This feature is useful if the fax number you are trying to reach is busy or temporarily unavailable. The HP All-in-One scans the originals into memory and sends them once it is able to connect to the receiving fax machine. After the HP All-in-One scans the pages into memory, you can immediately remove the originals from the document feeder tray.
To send a fax from memory
1.
Load your originals print side up into the document feeder tray.
NOTE:
This feature is not supported if you load your originals on the glass. You must load your originals in the document feeder tray.
2.
In the Fax area, press Menu.
The Enter Number prompt appears.
3.
Enter the fax number by using the keypad, press Speed Dial or a one-touch speed dial button to select a speed dial, or press Redial/Pause to redial the last number dialed.
4.
In the Fax area, press Menu repeatedly until How to Fax appears.
Send a fax 95
Chapter 9
5.
Press until Scan & Fax appears, and then press OK.
6.
Press Start Fax Black.
NOTE:
If you press Start Fax Color, the fax will be sent in black and white and a message appears on the display.
The HP All-in-One scans the originals into memory and sends the fax when the receiving fax machine is available.
Schedule a fax to send later
You can schedule a black-and-white fax to be sent within the next 24 hours. This enables you to send a black-and-white fax late in the evening, when phone lines are not as busy or phone rates are lower, for example. When scheduling a fax, the originals must be loaded in the document feeder tray and not on the glass. The HP All-in-One automatically sends your fax at the specified time.
You can only schedule one fax to be sent at a time. You can continue to send faxes normally, however, while a fax is scheduled.
NOTE:
You cannot schedule a color fax due to memory limitations.
To schedule a fax from the control panel
1.
Load your originals print side up into the document feeder tray.
NOTE:
Load your originals in the document feeder tray, and not on the glass.
This feature is not supported if you load your originals on the glass.
2.
In the Fax area, press Menu repeatedly until How to Fax appears.
3.
Press until Send Fax Later appears, and then press OK.
4.
Enter the send time by using the numeric keypad, and then press OK. If prompted, press 1 for AM, or 2 for PM.
5.
Enter the fax number by using the keypad, press Speed Dial or a one-touch speed dial button to select a speed dial, or press Redial/Pause to redial the last number dialed.
6.
Press Start Fax Black.
The HP All-in-One scans all pages and the scheduled time appears on the display.
The HP All-in-One sends the fax at the scheduled time.
To cancel a scheduled fax
1.
In the Fax area, press Menu repeatedly until How to Fax appears.
2.
Press until Send Fax Later appears, and then press OK.
If there is a fax already scheduled, the Cancel prompt appears on the display.
3.
Press 1 to select Yes.
NOTE:
You can also cancel the scheduled fax by pressing Cancel on the control panel when the scheduled time is visible on the display.
96 Use the fax features
Send a fax to multiple recipients
You can send a fax to multiple recipients at once by grouping individual speed dial entries into group speed dial entries.
To send a fax to multiple recipients from the control panel
1.
Load your originals print side up into the document feeder tray. If you are sending a single-page fax, such as a photograph, you can also load your original print side down on the glass.
NOTE:
If you are sending a multiple-page fax, you must load the originals in the document feeder tray. You cannot fax a multiple-page document from the glass.
2.
Press Speed Dial repeatedly, until the appropriate group speed dial entry appears.
TIP:
You can also scroll through the speed dial entries by pressing or , or you can select a speed dial entry by entering its speed dial code using the keypad on the control panel.
3.
Press Start Fax Black.
• If the device detects an original loaded in the automatic document feeder, the HP All-in-One sends the document to each number in the group speed dial entry.
•
If the device does not detect an original loaded in the automatic document
feeder, the Fax from glass? prompt appears. Make sure your original is loaded on the glass, and then press 1 to select Yes.
NOTE:
You can only use group speed dial entries to send faxes in black and white, because of memory limitations. The HP All-in-One scans the fax into memory then dials the first number. When a connection is made, the HP All-in-
One sends the fax and dials the next number. If a number is busy or not answering, the HP All-in-One follows the settings for Busy Redial and No Answer Redial.
If a connection cannot be made, the next number is dialed and an error report is generated.
To send a fax to multiple recipients from the HP Photosmart Studio (Mac) Software
1.
Load your originals print side up into the document feeder tray. If you are sending a single-page fax, such as a photograph, you can also load your original print side down on the glass.
2.
Select the HP Device Manager from the Dock.
The HP Device Manager window appears.
3.
In the Devices pop-up menu, choose the HP All-in-One, and then double-click Send
Fax.
The Print dialog box opens.
4.
From the Printer pop-up menu, choose the HP All-in-One (Fax).
5.
From the pop-up menu, choose Fax Recipients.
Send a fax 97
Chapter 9
6.
Enter the recipient information, and then click Add to Recipients.
NOTE:
You can also add recipients from the Phone Book or from the Address
Book. To select a recipient from the Address Book, click Open Address
Book, and then drag and drop the recipient to the Fax Recipients area.
7.
Continue to enter recipients, clicking Add to Recipients after each one, until all the appropriate recipients are in the Recipient List.
8.
Click Send Fax Now.
Related topics
•
Set up group speed dial entries
•
Print fax confirmation reports
Send a color original or photo fax
You can fax a color original or photo from the HP All-in-One. If the HP All-in-One determines that the recipient's fax machine only supports black-and-white faxes, the
HP All-in-One sends the fax in black and white.
HP recommends that you use only color originals for color faxing.
To send a color original or photo fax from the control panel
1.
Load your originals print side up into the document feeder tray. If you are sending a single-page fax, such as a photograph, you can also load your original print side down on the glass.
NOTE:
If you are sending a multiple-page fax, you must load the originals in the document feeder tray. You cannot fax a multiple-page document from the glass.
TIP:
To center a 10 x 15 cm (4 x 6 inch) photo, place the photo on the center of a blank letter- or A4-size sheet of paper, and then place the original on the glass.
2.
In the Fax area, press Menu.
The Enter Number prompt appears.
3.
Enter the fax number by using the keypad, press Speed Dial or a one-touch speed dial button to select a speed dial, or press Redial/Pause to redial the last number dialed.
4.
Press Start Fax Color.
• If the device detects an original loaded in the automatic document feeder, the HP All-in-One sends the document to the number you entered.
•
If the device does not detect an original loaded in the automatic document
feeder, the Fax from glass? prompt appears. Make sure your original is loaded on the glass, and then press 1 to select Yes.
NOTE:
If the recipient's fax machine only supports black-and-white faxes, the
HP All-in-One automatically sends the fax in black and white. A message appears after the fax has been sent indicating that the fax was sent in black and white.
Press OK to clear the message.
98 Use the fax features
Send a fax from the computer
You can load a black-and-white or color document, such as a photo, in the HP All-in-One, then send it as a fax with a cover page by using the HP Photosmart Studio (Mac) Software that came with the HP All-in-One. You can also send a file on your computer as a fax directly from the software application in which you are working on it.
This section contains the following topics:
•
Send a fax from the HP Photosmart Studio (Mac) Software
•
Send a fax from a software application
•
Send a computer-generated cover page as a single-page fax
Send a fax from the HP Photosmart Studio (Mac) Software
You can load a black-and-white or color document in the automatic document feeder or on the glass of the HP All-in-One then send the document as a fax with a cover page by using the HP Photosmart Studio (Mac) Software.
To send a fax from the HP Photosmart Studio (Mac) Software
1.
Load your originals print side up into the document feeder tray. If you are sending a single-page fax, such as a photograph, you can also load your original print side down on the glass.
NOTE:
If you are sending a multiple-page fax, you must load the originals in the document feeder tray. You cannot fax a multiple-page document from the glass.
2.
Select the HP Device Manager from the Dock.
The HP Device Manager window appears.
3.
From theTasks menu, double-click Send Fax.
The Print dialog box opens.
4.
From the Printer pop-up menu, choose the HP All-in-One (Fax).
5.
From the pop-up menu, choose Fax Recipients.
The Fax Recipients dialog box opens.
6.
In the To area, enter the fax number and other recipient information, and then click
Add to Recipients.
The recipient is added to the Recipient List.
NOTE:
You can also add recipients from the Phone Book or from the Address
Book. To select a recipient from the Address Book, click Open Address
Book, and then drag and drop the recipient to the Fax Recipients area.
7.
If you want to send the fax in color, choose Color from the Fax Mode pop-up menu.
8.
If your originals are loaded in the document feeder tray, choose Document Feeder from the Fax Pages from pop-up menu.
Send a fax 99
Chapter 9
9.
If you want to include a cover page, do the following:
a. From the pop-up menu, choose HP Fax Cover Page.
The HP Fax Cover Page dialog box opens.
b. From the Print Cover Page area, select whether you want to print the cover page before or after the document you are faxing.
c. From the Cover Page Type pop-up menu, choose the template that you want to use.
10.
Click Send Fax Now.
Send a fax from a software application
You can send a file on your computer as a fax directly from the software application in which you are working on it, such as a word processing or spreadsheet program.
To send a fax from a software application
1.
Open the file that you want to fax in its native software application.
2.
From the File menu in your software application, choose Print.
The Print dialog box opens.
3.
From the Printer pop-up menu, choose the HP All-in-One (Fax).
4.
In the Copies & Pages area, do one of the following:
• Select All to fax all pages of the current document.
• Specify a page range if you want to fax only a section of your document.
5.
From the pop-up menu, choose Fax Recipients.
The Fax Recipients dialog box opens.
6.
In the To area, enter the fax number and other recipient information, and then click
Add to Recipients.
The recipient is added to the Recipient List.
NOTE:
You can also add recipients from the Phone Book or from the Address
Book. To select a recipient from the Address Book, click Open Address
Book, and then drag and drop the recipient to the Fax Recipients area.
7.
If you want to send the fax in color, select Color in the Fax Mode area.
8.
If you want to include a cover page, do the following:
a. From the pop-up menu, choose HP Fax Cover Page.
The HP Fax Cover Page dialog box opens.
b. From the Cover Page Template pop-up menu, choose the template that you want to use.
A preview of the template appears in the Preview area of the Cover Page dialog box.
c. Fill in the appropriate information in the available boxes.
9.
Click Send Fax Now.
Send a computer-generated cover page as a single-page fax
Using the HP Photosmart Studio (Mac) Software, you can prepare a fax composed only of a cover page.
100 Use the fax features
To send a computer-generated cover page as a single-page fax
1.
Select the HP Device Manager from the Dock.
The HP Device Manager window appears.
2.
In the Tasks menu, double-click Send Fax.
The Print dialog box opens.
3.
From the Printer pop-up menu, choose the HP All-in-One (Fax).
4.
From the pop-up menu, choose Fax Recipients.
The Fax Recipients dialog box opens.
5.
In the To area, enter the fax number and other recipient information, and then click
Add to Recipients.
The recipient is added to the Recipient List.
NOTE:
You can also add recipients from the Phone Book or from the Address
Book. To select a recipient from the Address Book, click Open Address
Book, and then drag and drop the recipient to the Fax Recipients area.
6.
From the pop-up menu, choose Cover Page.
The Cover Page dialog box opens.
7.
From the Cover Page Type pop-up menu, choose the template that you want to use.
A preview of the template appears in the Preview area of the Cover Page dialog box.
8.
Fill in the appropriate information in the available boxes.
9.
Click Send Fax Now.
Change the fax resolution and Lighter / Darker settings
You can change the Resolution and Lighter / Darker settings for documents that you are faxing.
NOTE:
These settings do not affect copy settings. Copy resolution and lightness/ darkness are set independently from fax resolution and lightness/darkness. Also, the settings that you change from the control panel do not affect faxes you send from your computer.
This section contains the following topics:
•
•
Change the Lighter / Darker setting
•
Change the fax resolution
The Resolution setting affects the transmission speed and quality of faxed black-andwhite documents. If the receiving fax machine does not support the resolution you have chosen, the HP All-in-One sends faxes at the highest resolution supported by the receiving fax machine.
NOTE:
You can only change the resolution for faxes that you are sending in black and white. The HP All-in-One sends all color faxes using Fine resolution.
Send a fax 101
Chapter 9
The following resolution settings are available for sending faxes: Fine, Very Fine,
Photo, and Standard.
• Fine: provides high-quality text suitable for faxing most documents. This is the default setting. When sending faxes in color, the HP All-in-One always uses the Fine setting.
• Very Fine: provides the best quality fax when you are faxing documents with very fine detail. If you choose Very Fine, be aware that the faxing process takes longer to complete and you can only send black-and-white faxes using this resolution. If you send a color fax, it will be sent using Fine resolution instead.
• Photo: provides the best quality fax when sending photographs in black and white.
If you choose Photo, be aware that the faxing process takes longer to complete.
When faxing photographs in black and white, HP recommends that you choose
Photo.
• Standard: provides the fastest possible fax transmission with the lowest quality.
When you exit the Fax menu, this option returns to the default setting unless you set your changes as the default.
To change the resolution from the control panel
1.
Load your originals print side up into the document feeder tray. If you are sending a single-page fax, such as a photograph, you can also load your original print side down on the glass.
NOTE:
If you are sending a multiple-page fax, you must load the originals in the document feeder tray. You cannot fax a multiple-page document from the glass.
2.
In the Fax area, press Menu.
The Enter Number prompt appears.
3.
Enter the fax number by using the keypad, press Speed Dial or a one-touch speed dial button to select a speed dial, or press Redial/Pause to redial the last number dialed.
4.
In the Fax area, press Menu repeatedly until Resolution appears.
5.
Press to select a resolution setting, and then press OK.
6.
Press Start Fax Black.
• If the device detects an original loaded in the automatic document feeder, the HP All-in-One sends the document to the number you entered.
•
If the device does not detect an original loaded in the automatic document
feeder, the Fax from glass? prompt appears. Make sure your original is loaded on the glass, and then press 1 to select Yes.
Related topics
Change the Lighter / Darker setting
You can change the contrast of a fax to be darker or lighter than the original. This feature is useful if you are faxing a document that is faded, washed out, or handwritten. You can darken the original by adjusting the contrast.
102 Use the fax features
NOTE:
The Lighter / Darker setting applies to black and white faxes only, not color faxes.
When you exit the Fax menu, this option returns to the default setting unless you set your changes as the default.
To change the Lighter / Darker setting from the control panel
1.
Load your originals print side up into the document feeder tray. If you are sending a single-page fax, such as a photograph, you can also load your original print side down on the glass.
NOTE:
If you are sending a multiple-page fax, you must load the originals in the document feeder tray. You cannot fax a multiple-page document from the glass.
2.
In the Fax area, press Menu.
The Enter Number prompt appears.
3.
Enter the fax number by using the keypad, press Speed Dial or a one-touch speed dial button to select a speed dial, or press Redial/Pause to redial the last number dialed.
4.
In the Fax area, press Menu repeatedly until Lighter / Darker appears.
5.
Press to lighten the fax or press to darken it, and then press OK.
The indicator moves to the left or right as you press an arrow button.
6.
Press Start Fax Black.
• If the device detects an original loaded in the automatic document feeder, the HP All-in-One sends the document to the number you entered.
•
If the device does not detect an original loaded in the automatic document
feeder, the Fax from glass? prompt appears. Make sure your original is loaded on the glass, and then press 1 to select Yes.
Related topics
Set new default settings
You can change the default value for the Resolution and Lighter / Darker settings through the control panel.
To set new default settings from the control panel
1.
Make changes to the Resolution and Lighter / Darker settings.
2.
In the Fax area, press Menu repeatedly until Set New Defaults appears.
3.
Press until Yes appears, and then press OK.
Send a fax in Error Correction Mode
Error Correction Mode (ECM) prevents loss of data due to poor phone lines by detecting errors that occur during transmission and automatically requesting retransmission of the erroneous portion. Phone charges are unaffected, or might even be reduced, on good phone lines. On poor phone lines, ECM increases sending time and phone charges, but sends the data much more reliably. The default setting is On. Turn ECM off only if it
Send a fax 103
Chapter 9 increases phone charges substantially, and you can accept poorer quality in exchange for reduced charges.
Before turning the ECM setting off, consider the following. If you turn ECM off
• The quality and transmission speed of faxes you send and receive are affected.
• The Fax Speed is automatically set to Medium.
• You will no longer be able to send or receive faxes in color.
To change the ECM setting from the control panel
1.
Press Setup.
2.
Press 5, and then press 6.
This selects Advanced Fax Setup and then selects Error Correction Mode.
3.
Press to select On or Off.
4.
Press OK.
Receive a fax
The HP All-in-One can receive faxes automatically or manually. If you turn off the Auto
Answer option, you will need to receive faxes manually. If you turn on the Auto
Answer option (the default setting), the HP All-in-One automatically answers incoming calls and receives faxes after the number of rings specified by the Rings to Answer setting. (The default Rings to Answer setting is five rings.)
You can receive faxes manually from a phone that is:
• Directly connected to the HP All-in-One (on the 2-EXT port)
• On the same telephone line, but not directly connected to the HP All-in-One
If you receive a legal-size fax and the HP All-in-One is not currently set to use legal-size paper, the device reduces the fax so that it fits on the paper that is loaded in the HP Allin-One. If you have disabled the Automatic Reduction feature, the HP All-in-One might print the fax on more than one page.
This section contains the following topics:
•
•
•
Reprint received faxes from memory
•
•
Forward faxes to another number
•
Set the paper size for received faxes
•
Set automatic reduction for incoming faxes
NOTE:
If you installed a photo print cartridge for printing photos, you might want to replace it with the black print cartridge when receiving faxes.
Receive a fax manually
When you are on the phone, the person you are speaking with can send you a fax while you are still connected. This is referred to as manual faxing. Use the instructions in this section to receive a manual fax.
104 Use the fax features
You can receive faxes manually from a phone that is:
• Directly connected to the HP All-in-One (on the 2-EXT port)
• On the same phone line, but not directly connected to the HP All-in-One
To receive a fax manually
1.
Make sure the HP All-in-One is turned on and you have paper loaded in the input tray.
2.
Remove any originals from the document feeder tray.
3.
Set the Rings to Answer setting to a high number to allow you to answer the incoming call before the HP All-in-One answers. Or, turn off the Auto Answer setting so that the HP All-in-One does not automatically answer incoming calls.
4.
If you are currently on the phone with the sender, instruct the sender to press Start on their fax machine.
5.
When you hear fax tones from a sending fax machine, do the following:
a. Press Start Fax Black or Start Fax Color on the control panel of the HP All-in-
One.
b. When prompted, press 2 to select Fax Receive.
c. After the HP All-in-One begins to receive the fax, you can hang up the phone or remain on the line. The phone line is silent during fax transmission.
Related topics
•
Set the number of rings before answering
•
Set up backup fax reception
Depending on your preference and security requirements, you can set up the HP All-in-
One to store all the faxes it receives, only the faxes it receives while the device is in an error condition, or none of the faxes it receives.
The following Backup Fax Reception modes are available:
On
On Error Only
Off
The default setting. When Backup Fax Reception is On, the HP All-in-One stores all faxes it receives in memory. This enables you to reprint up to eight of the most recently printed faxes if they are still saved in memory.
NOTE:
When the memory gets low, the HP All-in-One overwrites the oldest, printed faxes as it receives new faxes. If the memory becomes full of unprinted faxes, the HP All-in-One will stop answering incoming fax calls.
NOTE:
If you receive a fax that is too large, such as a very detailed color photo, it might not be stored in memory due to memory limitations.
Causes the HP All-in-One to store faxes in memory only if there is an error condition that prevents the HP All-in-One from printing the faxes (for example, if the HP All-in-One runs out of paper). The HP All-in-One will continue to store incoming faxes as long as there is memory available. (If the memory becomes full, the HP All-in-One will stop answering incoming fax calls.) When the error condition is resolved, the faxes stored in memory print automatically and are then deleted from memory.
Means that faxes are never stored in memory. (You might want to turn off Backup Fax Reception for security purposes, for example.) If an error
Receive a fax 105
Chapter 9
(continued) condition occurs that prevents the HP All-in-One from printing (for example, the HP All-in-One runs out of paper), the HP All-in-One will stop answering incoming fax calls.
NOTE:
If Backup Fax Reception is enabled and you turn off the HP All-in-One, all faxes stored in memory are deleted, including any unprinted faxes that you might have received while the HP All-in-One was in an error condition. You will need to contact the senders to ask them to resend any unprinted faxes. For a list of the faxes you have received, print the Fax Log. The Fax Log is not deleted when the HP All-in-One is turned off.
To set backup fax reception from the control panel
1.
Press Setup.
2.
Press 5, and then press 5 again.
This selects Advanced Fax Setup and then selects Backup Fax Reception.
3.
Press to select On, On Error Only, or Off.
4.
Press OK.
Related topics
Reprint received faxes from memory
Reprint received faxes from memory
If you set the Backup Fax Reception mode to On, the HP All-in-One stores faxes it receives in memory, whether the device has an error condition or not.
NOTE:
After the memory becomes full, the HP All-in-One overwrites the oldest, printed faxes as it receives new faxes. If all the stored faxes are unprinted, the HP Allin-One will not receive any more fax calls until you print or delete the faxes from memory. You might also want to delete the faxes in memory for security or privacy purposes. For more information, see
You can select to print only one fax, or to print all faxes in the stored memory. For example, you might need to reprint your faxes if you lost the copy of your last printout.
To reprint faxes in memory from the control panel
1.
Make sure you have paper loaded in the input tray.
2.
Press Setup.
3.
Press 6, and then press 5.
This selects Tools and then selects Reprint Faxes in Memory.
4.
Highlight Print One fax or Print All faxes, and then press OK.
• If you selected Print One fax, then highlight the fax you want to print and press OK.
• If you selected Print All faxes, the faxes are printed in the reverse order they were received with the most recently received fax printed first, and so on.
5.
If you want to stop reprinting the faxes in memory, press Cancel.
106 Use the fax features
To delete all the faxes in memory from the control panel
▲ Turn off the HP All-in-One by pressing the Power button.
All faxes stored in memory will be deleted from memory when you turn off the power to the HP All-in-One.
NOTE:
You can also delete any faxes stored in memory by selecting Clear Fax
Log from the Tools menu. To do so, press Setup, press 6, and then press 7.
Related topics
Poll to receive a fax
Polling allows the HP All-in-One to ask another fax machine to send a fax that it has in its queue. When you use the Poll to Receive feature, the HP All-in-One calls the designated fax machine and requests the fax from it. The designated fax machine must be set for polling and have a fax ready to send.
NOTE:
The HP All-in-One does not support polling pass codes. Polling pass codes are a security feature that require the receiving fax machine to provide a pass code to the device it is polling in order to receive the fax. Make sure the device you are polling does not have a pass code set up (or has not changed the default pass code) or the HP All-in-One will not be able to receive the fax.
To set up poll to receive a fax from the control panel
1.
In the Fax area, press Menu repeatedly until How to Fax appears.
2.
Press until Poll to Receive appears, and then press OK.
3.
Enter the fax number of the other fax machine.
4.
Press Start Fax Black or Start Fax Color.
NOTE:
If you press Start Fax Color but the sender sent the fax in black and white, the HP All-in-One prints the fax in black and white.
Forward faxes to another number
You can set up the HP All-in-One to forward your faxes to another fax number. If you receive a color fax, the HP All-in-One forwards the fax in black and white.
HP recommends that you verify the number you are forwarding to is a working fax line.
Send a test fax to make sure the fax machine is able to receive your forwarded faxes.
To forward faxes from the control panel
1.
Press Setup.
2.
Press 5, and then press 8.
This selects Advanced Fax Setup and then selects Fax Forwarding Black Only.
Receive a fax 107
Chapter 9
3.
Press until On-Forward or On-Print & Forward appears, and then press OK.
• Choose On-Forward if you want to forward the fax to another number without printing a backup copy on the HP All-in-One.
NOTE:
If the HP All-in-One is not able to forward the fax to the designated fax machine (if it is not turned on, for example), the HP All-in-One will print the fax. If you set up the HP All-in-One to print error reports for received faxes, it will also print an error report.
• Choose On-Print & Forward to print a backup copy of your received fax on the
HP All-in-One while forwarding the fax to another number.
4.
At the prompt, enter the number of the fax machine that will receive the forwarded faxes.
5.
At the prompt, enter a start time and date and a stop time and date.
6.
Press OK.
Fax Forwarding appears on the display.
If the HP All-in-One loses power when Fax Forwarding is set up, the HP All-in-One saves the Fax Forwarding setting and phone number. When power is restored to the device, the Fax Forwarding setting is still On.
NOTE:
You can cancel fax forwarding by pressing Cancel on the control panel when the Fax Forwarding message is visible on the display, or you can select
Off from the Fax Forwarding Black Only menu.
To forward faxes from the HP Photosmart Studio (Mac) Software
1.
Select the HP Device Manager from the Dock.
The HP Device Manager window appears.
2.
In the Information and Settings drop-down menu, choose Fax Setup Utility.
The Device Settings dialog box opens.
3.
From the pop-up menu, choose Fax Forward.
The Fax Forward dialog box appears.
4.
Select Forward Fax.
5.
In the Forward Fax Number box, type the forwarding number.
6.
When you are finished, click Apply or OK.
Set the paper size for received faxes
You can select the paper size for received faxes. The paper size you select should match what is loaded in your input tray. Faxes can be printed on letter, A4, or legal paper only.
NOTE:
If an incorrect paper size is loaded in the input tray when you receive a fax, the fax does not print and an error message appears on the display. Load letter, A4, or legal paper, and then press OK to print the fax.
108 Use the fax features
To set the paper size for received faxes from the control panel
1.
Press Setup.
2.
Press 4, and then press 4.
This selects Basic Fax Setup and then selects Fax Paper Size.
3.
Press to select an option, and then press OK.
Set automatic reduction for incoming faxes
The Automatic Reduction setting determines what the HP All-in-One does if it receives a fax that is too large for the default paper size. This setting is turned on by default, so the image of the incoming fax is reduced to fit on one page, if possible. If this feature is turned off, information that does not fit on the first page is printed on a second page.
Automatic Reduction is useful when you receive a legal-size fax and letter-size paper is loaded in the input tray.
To set automatic reduction from the control panel
1.
Press Setup.
2.
Press 5, and then press 4.
This selects Advanced Fax Setup and then selects Automatic Reduction.
3.
Press to select Off or On.
4.
Press OK.
Block junk fax numbers
If you subscribe to a caller ID service through your phone provider, you can block specific fax numbers, so the HP All-in-One does not print faxes received from those numbers in the future. When an incoming fax call is received, the HP All-in-One compares the number to the list of junk fax numbers you set up to determine if the call should be blocked. If the number matches a number in the blocked fax numbers list, the fax is not printed. (The maximum number of fax numbers you can block varies by model.)
This section contains the following topics:
•
•
Add numbers to the junk fax list
•
Remove numbers from the junk fax list
NOTE:
This feature is not supported in all countries/regions. If it is not supported in your country/region, Junk Fax Blocker Set Up does not appear in the Basic Fax
Setup menu.
Set the junk fax mode
By default, Block Junk Fax mode is turned On. If you do not subscribe to a caller ID service through your phone provider, or do not want to use this feature, you can turn off this setting.
Block junk fax numbers 109
Chapter 9
To set the junk fax mode
1.
Press Setup.
2.
Press 4, and then press 7.
This selects Basic Fax Setup and then selects Junk Fax Blocker Set Up.
3.
Press 4 to select Block Junk Fax.
4.
Press to select On or Off, and then press OK.
Add numbers to the junk fax list
There are two ways to add a number to your junk list. You can select numbers from your caller ID history, or you can enter new numbers. The numbers in your junk list will be blocked if Block Junk Fax mode is set to On.
To select a number from the caller ID list
1.
Press Setup.
2.
Press 4 and then press 7.
This selects Basic Fax Setup and then selects Junk Fax Blocker Set Up.
3.
Press 1, and then press 1.
This selects Add Number to Junk List and then selects Select Number.
4.
Press to scroll through the numbers from which you have received faxes. When the number you want to block appears, press OK to select it.
5.
When the Select Another? prompt appears, do one of the following:
• If you want to add another number to the list of junk fax numbers, press 1 to select Yes, and then repeat step 4 for each number you want to block.
• If you are done, press 2 to select No.
To manually enter a number to block
1.
Press Setup.
2.
Press 4, and then press 7.
This selects Basic Fax Setup and then selects Junk Fax Blocker Set Up.
3.
Press 1, and then press 2.
This selects Add Number to Junk List and then selects Enter Number.
4.
Use the keypad to enter a fax number to block and then press OK.
Make sure you enter the fax number as it appears on the display, and not the fax number that appears on the fax header of the received fax, as these numbers can be different.
5.
When the Enter Another? prompt appears, do one of the following:
• If you want to add another number to the list of junk fax numbers, press 1 to select Yes, and then repeat step 4 for each number you want to block.
• If you are done, press 2 to select No.
Remove numbers from the junk fax list
If you no longer want to block a fax number, you can remove a number from your junk fax list.
110 Use the fax features
To remove numbers from the list of junk fax numbers
1.
Press Setup.
2.
Press 4, and then press 7.
This selects Basic Fax Setup and then selects Junk Fax Blocker Set Up.
3.
Press 2.
This selects Remove Number from Junk List.
4.
Press to scroll through the numbers you have blocked. When the number you want to remove appears, press OK to select it.
5.
When the Delete Another? prompt appears, do one of the following:
• If you want to remove another number from the list of junk fax numbers, press 1 to select Yes, and then repeat step 4 for each number you want to block.
• If you are done, press 2 to select No.
Fax over the Internet using IP phone
You might subscribe to a low-cost phone service that allows you to send and receive faxes with the HP All-in-One by using the Internet. This method is called Fax over Internet
Protocol (FoIP). You probably use a FoIP service (provided by your telephone company) if you:
• Dial a special access code along with the fax number, or
• Have an IP converter box that connects to the Internet and provides analog phone ports for the fax connection.
NOTE:
You can only send and receive faxes by connecting a phone cord to the 1-
LINE port on the back of the HP All-in-One. This means that your connection to the
Internet must be done either through a converter box (which supplies regular analog phone jacks for fax connections) or your telephone company.
The FoIP service might not work properly when the HP All-in-One is sending and receiving faxes at high speed (33600 bps). If you experience problems sending and receiving faxes, use a slower fax speed. You can do this by changing the Fax Speed setting from Fast
(the default) to Medium.
You should also check with your telephone company to make sure their Internet phone service supports faxing. If they do not support faxing, you might encounter intermittent problems when trying to send and receive faxes through the Internet.
Related topics
Print reports
You can set up the HP All-in-One to print error reports and confirmation reports automatically for each fax you send and receive. You can also manually print system reports as you need them; these reports provide useful system information about the
HP All-in-One.
By default, the HP All-in-One is set to print a report only if there is a problem with sending or receiving a fax. A confirmation message that indicates whether a fax was successfully sent appears briefly on the display after each transaction.
Fax over the Internet using IP phone 111
Chapter 9
This section contains the following topics:
•
Print fax confirmation reports
•
•
•
Print fax confirmation reports
If you need printed confirmation that your faxes were successfully sent, follow these instructions to enable fax confirmation before sending any faxes. Select either On Fax
Send or Send & Receive.
The default fax confirmation setting is Off. This means that the HP All-in-One will not print a confirmation report for each fax sent or received. A confirmation message indicating whether a fax was successfully sent appears briefly on the display after each transaction.
To enable fax confirmation from the control panel
1.
Press Setup.
2.
Press 2, and then press 3.
This selects Print Report and then selects Fax Confirmation.
3.
Press to select one of the following, and then press OK.
Off
On Fax Send
On Fax Receive
Send & Receive
Does not print a fax confirmation report when you send and receive faxes successfully. This is the default setting.
Prints a fax confirmation report for every fax you send.
Prints a fax confirmation report for every fax you receive.
Prints a fax confirmation report for every fax you send and receive.
TIP:
If you choose On Fax Send or Send & Receive, and scan your fax to send from memory, you can include an image of the first page of the fax on the Fax
Sent Confirmation report. Press Setup, press 2, and then press 2 again.
Select On from the Image on Fax Send Report menu.
Print fax error reports
You can configure the HP All-in-One so that it automatically prints a report when there is an error during transmission or reception.
To set the HP All-in-One to print fax error reports automatically
1.
Press Setup.
2.
Press 2, and then press 3.
This selects Print Report and then selects Fax Error Report.
3.
Press to select one of the following, and then press OK.
Send & Receive
Off
Prints whenever there is any kind of fax error. This is the default setting.
Does not print any fax error reports.
112 Use the fax features
On Fax Send
On Fax Receive
Prints whenever there is a transmission error.
Prints whenever there is a receiving error.
Print the fax log
The fax log enables you to print a log of approximately the last 30 fax transactions. If a fax transaction had an error, the error is indicated by an error code in the fax log.
If necessary (for security purposes, for example), you can easily clear the entire log from memory. This also deletes any saved faxes from memory.
For more information on possible error codes in the fax log, see the
To print the fax log from the control panel
1.
Press Setup.
2.
Press 2, and then press 6.
This selects Print Report and then prints the fax log.
To clear the fax log from memory
1.
Press Setup.
2.
Press 6, and then press 7.
This selects Tools menu and then selects Clear Fax Log.
The fax log and any faxes that might have been stored in memory are deleted.
To print or save the fax log from the HP Photosmart Studio (Mac) Software
1.
Select the HP Device Manager from the Dock.
The HP Device Manager window appears.
2.
From the Information and Settings drop-down, select Fax Setup Utility.
3.
From the pop-up menu, choose Fax Log.
4.
From the pop-up menu, choose either Received or Sent.
You can sort the log by clicking on the column headers.
5.
Click the Print or Save button above the log to print the list of fax logs or save them.
Print other reports
You can manually generate reports about the HP All-in-One, such as the status of the last fax you sent, a list of programmed speed dial entries, or a self-test report for diagnostic purposes.
Print reports 113
Chapter 9
To print reports from the control panel
1.
Press Setup, and then press 2.
This selects Print Report.
2.
Press to select one of the following, and then press OK.
Fax Confirmation
Lets you set up fax confirmation reports to print automatically.
TIP:
If you choose On Fax Send or Send & Receive, and scan your fax to send from memory, you can include an image of the first page of the fax on the Fax Sent Confirmation report. Press Setup, press 2, and then press 2 again. Select On from the Image on Fax Send Report menu.
Fax Error Report
Lets you set up fax error reports to print automatically.
Self-Test Report
Prints a report to assist you in diagnosing print and alignment problems.
This report also contains valuable information if you need to call HP
Support.
Last Transaction
Prints details of the last fax transaction.
Fax Log
Prints a log of approximately the last 30 fax transactions.
Speed Dial List
Caller ID Report
Prints a list of programmed speed dial entries. You can also print this report by selecting Print Speed Dial List from the Speed Dial Setup menu. To do so, press Setup, press 2, and then press 4.
If you subscribe to a caller ID service through your phone provider, this report prints a list of approximately the last 30 fax calls you received.
The report shows the phone number, date and time, and, depending on the format your phone provider uses to transmit caller ID information, might include the name of the sender.
NOTE:
This feature is not supported in all countries/regions. If it is not supported in your country/region, Caller ID Report does not appear in the Print Report menu.
Junk Fax List
If you subscribe to a caller ID service through your phone provider, and have designated any numbers as junk fax numbers, this report prints a list of the phone numbers you have blocked. (The maximum number of fax numbers you can block varies by model.)
NOTE:
This feature is not supported in all countries/regions. If it is not supported in your country/region, Junk Fax List does not appear in the Print Report menu.
Related topics
•
Print fax confirmation reports
•
•
•
•
Stop faxing
You can cancel a fax you are sending or receiving at any time.
114 Use the fax features
To stop faxing from the control panel
▲ Press Cancel on the control panel to stop a fax you are sending or receiving. If the
HP All-in-One does not stop faxing, press Cancel again.
The HP All-in-One prints any pages it has already started printing and then cancels the remainder of the fax. This can take a few moments.
To cancel a number you are dialing
▲ Press Cancel to cancel a number you are currently dialing.
To cancel a fax from the HP Photosmart Studio (Mac) Software
1.
Open the Printer Setup Utility (v 10.3 or later) from the Applications:Utilities folder.
2.
Make sure the HP All-in-One (Fax) is selected.
3.
From the Printers menu, choose Show Jobs.
4.
Select the fax you want to cancel.
5.
Click Delete.
Stop faxing 115
Chapter 9
116 Use the fax features
10 Maintain the HP All-in-One
The HP All-in-One requires little maintenance. Sometimes you might want to clean the glass and lid backing to remove surface dust and ensure that your copies and scans remain clear. You will also need to replace, align, or clean your print cartridges from time to time. This section provides instructions for keeping the HP All-in-One in top working condition. Perform these simple maintenance procedures as necessary.
This section contains the following topics:
•
•
Check the estimated ink levels
•
•
Clean the HP All-in-One
To ensure that your copies and scans remain clear, you might need to clean the glass and lid backing. You might also want to dust the exterior of the HP All-in-One.
This section contains the following topics:
•
•
•
•
Clean the automatic document feeder
Clean the glass
Glass that is dirty from fingerprints, smudges, hair, and dust on the main glass surface slows down performance and affects the accuracy of features such as Fit to Page.
In addition to the main glass surface, you might also need to clean the small glass strip inside the automatic document feeder. Streaks can occur if the glass strip inside the automatic document feeder is dirty.
To clean the glass
1.
Turn off the HP All-in-One, and raise the lid.
2.
Clean the glass with a soft cloth or sponge slightly moistened with a nonabrasive glass cleaner.
CAUTION:
Do not use abrasives, acetone, benzene, or carbon tetrachloride on the glass, since they can damage it. Do not place or spray liquid directly on the glass. The liquid might seep under the glass and damage the device.
3.
Dry the glass with a dry, soft, lint-free cloth to prevent spotting.
4.
Turn on the HP All-in-One.
Clean the lid backing
Minor debris can accumulate on the white document backing located underneath the lid of the HP All-in-One.
Maintain the HP All-in-One 117
Chapter 10
To clean the lid backing
1.
Turn off the HP All-in-One, unplug the power cord, and raise the lid.
NOTE:
Depending how long the HP All-in-One is unplugged, the date and time might be erased. You might need to reset the date and time later, when you plug the power cord back in.
2.
Clean the white document backing with a soft cloth or sponge slightly moistened with a mild soap and warm water.
Wash the backing gently to loosen debris. Do not scrub the backing.
3.
Dry the backing with a dry, soft, lint-free cloth.
CAUTION:
Do not use paper-based wipes, as these might scratch the backing.
4.
If further cleaning is needed, repeat the previous steps using isopropyl (rubbing) alcohol, and wipe the backing thoroughly with a damp cloth to remove any residual alcohol.
CAUTION:
Be careful not to spill alcohol on the glass or exterior of the HP Allin-One, as this might damage the device.
Clean the exterior
Use a soft cloth or slightly moistened sponge to wipe dust, smudges, and stains off the case. The interior of the HP All-in-One does not require cleaning. Keep fluids away from the control panel and the interior of the HP All-in-One.
CAUTION:
To avoid damage to the exterior of the HP All-in-One, do not use alcohol or alcohol-based cleaning products.
Clean the automatic document feeder
If the automatic document feeder picks up multiple pages or if it does not pick up plain paper, you can clean the rollers and separator pad. Lift the automatic document feeder
118 Maintain the HP All-in-One
cover to access the pick assembly inside the automatic document feeder, clean the rollers or separator pad, and then close the cover.
To clean the rollers or separator pad
1.
Remove all originals from the document feeder tray.
2.
Lift the automatic document feeder cover (1).
This provides easy access to the rollers (2) and separator pad (3), as shown below.
1 Automatic document feeder cover
2 Rollers
3 Separator pad
3.
Lightly dampen a clean lint-free cloth with distilled water, then squeeze any excess liquid from the cloth.
4.
Use the damp cloth to wipe any residue off the rollers or separator pad.
NOTE:
If the residue does not come off using distilled water, try using isopropyl
(rubbing) alcohol.
5.
Close the cover of the automatic document feeder.
Clean the HP All-in-One 119
Chapter 10
To clean the glass strip inside the automatic document feeder
1.
Turn off the HP All-in-One, and unplug the power cord.
NOTE:
Depending how long the HP All-in-One is unplugged, the date and time might be erased. You might need to reset the date and time later, when you plug the power cord back in.
2.
Lift the cover of the automatic document feeder.
3.
Raise the lid, as if you were loading an original on the glass.
4.
Lift the automatic document feeder mechanism.
120 Maintain the HP All-in-One
There is a glass strip under the automatic document feeder.
5.
Clean the glass strip with a soft cloth or sponge slightly moistened with a nonabrasive glass cleaner.
CAUTION:
Do not use abrasives, acetone, benzene, or carbon tetrachloride on the glass, since they can damage it. Do not place or spray liquid directly on the glass. The liquid might seep under the glass and damage the device.
6.
Lower the automatic document feeder mechanism, and then close the cover of the automatic document feeder.
7.
Close the lid.
8.
Plug in the power cord, and then turn on the HP All-in-One.
Check the estimated ink levels
You can easily check the ink supply level to determine how soon you might need to replace a print cartridge. The ink supply level shows an estimate of the amount of ink remaining in the print cartridges.
TIP:
You can also print a self-test report to see if your print cartridges might need to be replaced.
NOTE:
The HP All-in-One can only detect the ink levels for genuine HP ink. The ink levels in print cartridges that are refilled or have been used in other devices, might not register accurately.
NOTE:
The ink levels shown are an estimate only. Actual ink volumes may vary.
To check the ink levels from the HP Photosmart Studio (Mac) Software
1.
Select the HP Device Manager from the Dock.
The HP Device Manager window appears.
2.
Make sure the HP All-in-One is selected in the Devices pop-up menu.
3.
From the Information and Settings pop-up menu, choose Maintain Printer.
The Select Printer window appears.
4.
If the Select Printer dialog box appears, choose the HP All-in-One, and then click
Launch Utility.
5.
Click Supplies Status.
The estimated ink levels for the print cartridges appear.
Check the estimated ink levels 121
Chapter 10
Related topics
Print a self-test report
If you are experiencing problems with printing, print a self-test report before you replace the print cartridges. This report provides useful information on several aspects of your device, including your print cartridges.
To print a self-test report
1.
Load letter, A4, or legal unused plain white paper into the input tray.
2.
Press Setup.
3.
Press 2, then press 4.
This selects Print Report and then selects Self-Test Report.
The HP All-in-One prints a self-test report, which might indicate the source of the printing problem. A sample of the ink test area of the report is shown below.
4.
Make sure the lines of color extend across the page.
If the black line is missing, faded, streaked, or shows lines, this might indicate a problem with the black print cartridge in the right slot.
If any of the remaining three lines are missing, faded, streaked, or show lines, this might indicate a problem with the tri-color print cartridge in the left slot.
If the color bars do not appear as black, cyan, magenta and yellow, you might need to clean the print cartridges. If the problem is not resolved by cleaning the print cartridges, you might need to replace the print cartridges.
Related topics
•
•
•
122 Maintain the HP All-in-One
Work with print cartridges
To ensure the best print quality from the HP All-in-One, you will need to perform some simple maintenance procedures and, when prompted by a message on the display, replace the print cartridges.
NOTE:
Ink from cartridges is used in the printing process in a number of different ways, including in the initialization process, which prepares the device and cartridges for printing, and in printhead servicing, which keeps print nozzles clear and ink flowing smoothly. In addition, some residual ink is left in the cartridge after it is used.
For more information see www.hp.com/go/inkusage .
This section contains the following topics:
•
•
•
•
Use the print cartridge protector
•
•
•
Clean the print cartridge contacts
•
Clean the area around the ink nozzles
Handle the print cartridges
Before you replace or clean a print cartridge, you should know the part names and how to handle the print cartridges.
1 Copper-colored contacts
2 Plastic tape with pink pull tab (must be removed before installing)
3 Ink nozzles under tape
Hold the print cartridges by their black plastic sides, with the label on top. Do not touch the copper-colored contacts or the ink nozzles.
Work with print cartridges 123
Chapter 10
NOTE:
Handle the print cartridges carefully. Dropping or jarring cartridges can cause temporary printing problems, or even permanent damage.
Replace the print cartridges
Follow these instructions when the ink level is low.
NOTE:
When the ink level for the print cartridge is low, a message appears on the display. You can also check the ink levels by using the HP Photosmart Studio (Mac)
Software on your computer.
NOTE:
When the ink level for the print cartridge is low, a message appears on the display. You can also check the ink levels by using the Printer Toolbox available through the HP Solution Center Software on your computer or through the Print
Properties dialog box on your computer.
When you receive a low-ink warning message on the display, make sure you have a replacement print cartridge available. You should also replace the print cartridges when you see faded text or if you experience print quality issues related to the print cartridges.
To order print cartridges for the HP All-in-One, go to www.hp.com/learn/suresupply . If prompted, choose your country/region, follow the prompts to select your product, and then click one of the shopping links on the page.
To replace the print cartridges
1.
Make sure the HP All-in-One is on.
CAUTION:
If the HP All-in-One is off when you open the print cartridge door to access the print cartridges, the HP All-in-One will not release the cartridges for changing. You might damage the HP All-in-One if the print cartridges are not docked safely when you try to remove them.
2.
Open the print cartridge door.
The print carriage should move to the far right side of the HP All-in-One. If the print carriage does not move to the right side, close the door. Then, turn the HP All-in-One off, and then on again.
124 Maintain the HP All-in-One
3.
Wait until the print carriage is idle and silent, and then lightly press down on a print cartridge to release it.
If you are replacing the tri-color print cartridge, remove the print cartridge from the slot on the left.
If you are replacing the black print cartridge, remove the print cartridge from the slot on the right.
1 Print cartridge slot for the tri-color print cartridge
2 Print cartridge slot for the black print cartridges
4.
Pull the print cartridge toward you out of its slot.
5.
If you are removing the print cartridge because it is low or out of ink, recycle the print cartridge. The HP Inkjet Supplies Recycling Program is available in many countries/ regions, and lets you recycle used print cartridges free of charge. For more information, go to the following website: www.hp.com/recycle
Work with print cartridges 125
Chapter 10
6.
Remove the new print cartridge from its packaging and, being careful to touch only the black plastic, gently remove the plastic tape by using the pink pull tab.
1 Copper-colored contacts
2 Plastic tape with pink pull tab (must be removed before installing)
3 Ink nozzles under tape
CAUTION:
Do not touch the copper-colored contacts or ink nozzles. Touching these parts can result in clogs, ink failure, and bad electrical connections.
7.
Slide the new print cartridge forward into the empty slot. Then gently push on the upper part of the print cartridge forward until it clicks into the socket.
If you are installing the tri-color print cartridge, slide it into the left slot.
If you are installing a black print cartridge, slide it into the right slot.
126 Maintain the HP All-in-One
8.
Close the print cartridge door.
9.
If you installed a new print cartridge, the print cartridge alignment process begins.
10.
Make sure you have plain paper loaded in the input tray, and press OK.
The HP All-in-One prints a print cartridge alignment sheet.
11.
Load the print cartridge alignment sheet print side up and top first in the center of the document feeder tray, and then press OK.
The HP All-in-One aligns the print cartridges. Recycle or discard the print cartridge alignment sheet.
Related topics
•
Check the estimated ink levels
•
Use a photo print cartridge
You can optimize the quality of the color photos you print and copy with the HP All-in-
One by purchasing a photo print cartridge. Remove the black print cartridge and insert the photo print cartridge in its place. With the tri-color print cartridge and photo print cartridge installed, you have a six-ink system, which provides enhanced quality color photos.
When you want to print regular text documents, swap the black print cartridge back in.
Use a print cartridge protector or an airtight plastic container to keep your print cartridge secure when it is not being used.
Related topics
•
•
•
Use the print cartridge protector
Work with print cartridges 127
Chapter 10
Use the print cartridge protector
In some countries/regions, when you purchase a photo print cartridge, you might also receive a print cartridge protector. In other countries/regions, a print cartridge protector comes in the box with the HP All-in-One. If neither your print cartridge nor the HP All-in-
One came with a print cartridge protector, you can use an airtight plastic container to protect your print cartridge.
The print cartridge protector is designed to keep a print cartridge secure and prevent it from drying out when it is not being used. Whenever you remove a print cartridge from the HP All-in-One with the intention of using it again later, store it in the print cartridge protector. For example, store the black print cartridge in a print cartridge protector if you are removing it so you can print high-quality photos with the photo and tri-color print cartridges.
To insert a print cartridge into the print cartridge protector
▲ Place the print cartridge into the print cartridge protector at a slight angle and snap it securely into place.
To remove the print cartridge from the print cartridge protector
▲ Press down on the top of the print cartridge protector to release the print cartridge, then gently remove the print cartridge out of the print cartridge protector.
Align the print cartridges
The HP All-in-One prompts you to align cartridges every time you install or replace a print cartridge. You can also align the print cartridges at any time from the control panel or by using the software you installed with the HP All-in-One. Aligning the print cartridges ensures high-quality output.
128 Maintain the HP All-in-One
NOTE:
If you remove and reinstall the same print cartridge, the HP All-in-One will not prompt you to align the print cartridges. The HP All-in-One remembers the alignment values for that print cartridge, so you do not need to realign the print cartridges.
To align the print cartridges from the control panel when prompted
1.
Load letter, A4, or legal unused plain white paper into the input tray.
NOTE:
If you have colored paper loaded in the input tray when you align the print cartridges, the alignment will fail. Load unused plain white paper into the input tray, and then try the alignment again.
If the alignment fails again, you might have a defective sensor or print cartridge.
Contact HP Support. Go to www.hp.com/support . If prompted, choose your country/region, and then click Contact HP for information on calling for technical support.
The HP All-in-One prints a print cartridge alignment sheet.
2.
Load the print cartridge alignment sheet print side down and top first in the center of the document feeder tray, and then press OK.
The HP All-in-One aligns the print cartridges. Recycle or discard the print cartridge alignment sheet.
To align the cartridges from the control panel at any time
1.
Load letter, A4, or legal unused plain white paper into the input tray.
NOTE:
If you have colored paper loaded in the input tray when you align the print cartridges, the alignment will fail. Load unused plain white paper into the input tray, and then try the alignment again.
If the alignment fails again, you might have a defective sensor or print cartridge.
Contact HP Support. Go to www.hp.com/support . If prompted, choose your country/region, and then click Contact HP for information on calling for technical support.
2.
Press Setup.
3.
Press 6, then press 2.
This selects Tools and then selects Align Print Cartridge.
The HP All-in-One prints a print cartridge alignment sheet.
4.
Load the print cartridge alignment sheet print side down and top first in the center of the document feeder tray, and then press OK.
The HP All-in-One aligns the print cartridges. Recycle or discard the print cartridge alignment sheet.
To align the print cartridges from the HP Photosmart Studio (Mac) Software
1.
Load letter, A4, or legal unused plain white paper into the input tray.
2.
Select the HP Device Manager from the Dock.
The HP Device Manager window appears.
3.
Make sure the HP All-in-One is selected in the Devices pop-up menu.
Work with print cartridges 129
Chapter 10
4.
From the Information and Settings pop-up menu, choose Maintain Printer.
The Select Printer window appears.
5.
If the Select Printer dialog box appears, choose the HP All-in-One, and then click
Launch Utility.
6.
Click Align in the Configuration Settings Panel.
7.
Click Align.
The HP All-in-One prints a print cartridge alignment sheet.
8.
Click Done if you are satisfied with the resules, or click Align to try again.
Clean the print cartridges
Use this feature when the self-test report shows streaking, white lines through any of the lines of color or when a color is muddy after installing a print cartridge for the first time.
Do not clean print cartridges unnecessarily, as this wastes ink and shortens the life of the ink nozzles.
To clean the print cartridges from the control panel
1.
Load letter, A4, or legal unused plain white paper into the input tray.
2.
Press Setup.
3.
Press 6, then press 1.
This selects Tools and then selects Clean Print Cartridge.
The HP All-in-One prints a page that you can recycle or discard.
If copy or print quality still seems poor after you clean the print cartridges, try cleaning the print cartridge contacts before replacing the affected print cartridge.
To clean the print cartridges from the HP Photosmart Studio (Mac) Software
1.
Load letter, A4, or legal unused plain white paper into the input tray.
2.
Select the HP Device Manager from the Dock.
The HP Device Manager window appears.
3.
Make sure the HP All-in-One is selected in the Devices pop-up menu.
4.
From the Information and Settings pop-up menu, choose Maintain Printer.
The Select Printer window appears.
5.
If the Select Printer dialog box appears, choose the HP All-in-One, and then click
Launch Utility.
The HP Printer Utility window appears.
6.
Click Clean in the Configuration Settings Panel.
7.
Click Clean.
8.
Follow the prompts until you are satisfied with the quality of the output, and then close the HP Printer Utility.
If copy or print quality still seems poor after you clean the print cartridges, try cleaning the print cartridge contacts before replacing the affected print cartridge.
Related topics
•
Clean the print cartridge contacts
•
130 Maintain the HP All-in-One
Clean the print cartridge contacts
Clean the print cartridge contacts only if you get repeated messages on the display prompting you to check a print cartridge after you already have cleaned or aligned the print cartridges.
Before cleaning the print cartridge contacts, remove the print cartridge and verify that nothing is covering the print cartridge contacts, then reinstall the print cartridge. If you continue to get messages to check the print cartridges, clean the print cartridge contacts.
Make sure you have the following materials available:
• Dry foam rubber swabs, lint-free cloth, or any soft material that will not come apart or leave fibers.
TIP:
Coffee filters are lint-free and work well for cleaning print cartridges.
• Distilled, filtered, or bottled water (tap water might contain contaminants that can damage the print cartridges).
CAUTION:
Do not use platen cleaners or alcohol to clean the print cartridge contacts. These can damage the print cartridge or the HP All-in-One.
To clean the print cartridge contacts
1.
Turn on the HP All-in-One and open the print cartridge door.
The print carriage moves to the far right side of the HP All-in-One.
2.
Wait until the print carriage is idle and silent, and then unplug the power cord from the back of the HP All-in-One.
NOTE:
Depending how long the HP All-in-One is unplugged, the date and time might be erased. You might need to reset the date and time later, when you plug the power cord back in.
3.
Lightly press down on the print cartridge to release it, and then pull it toward you out of the slot.
NOTE:
Do not remove both print cartridges at the same time. Remove and clean each print cartridge one at a time. Do not leave a print cartridge outside the HP Allin-One for more than 30 minutes.
4.
Inspect the print cartridge contacts for ink and debris buildup.
5.
Dip a clean foam rubber swab or lint-free cloth into distilled water, and squeeze any excess water from it.
6.
Hold the print cartridge by its sides.
Work with print cartridges 131
Chapter 10
7.
Clean only the copper-colored contacts. Allow the print cartridges to dry for approximately ten minutes.
1 Copper-colored contacts
2 Ink nozzles (do not clean)
8.
Slide the print cartridge back into the slot. Push the print cartridge forward until it clicks into place.
9.
Repeat if necessary for the other print cartridge.
10.
Gently close the print cartridge door and plug the power cord into the back of the
HP All-in-One.
Related topics
Clean the area around the ink nozzles
Clean the area around the ink nozzles
If the HP All-in-One is used in a dusty environment, a small amount of debris might accumulate inside the device. This debris can include dust, hair, carpet, or clothing fibers.
When debris gets on the print cartridges, it can cause ink streaks and smudges on printed pages. Ink streaking can be corrected by cleaning around the ink nozzles as described here.
NOTE:
Clean the area around the ink nozzles only if you continue to see streaks and smudges on your printed pages after you have already cleaned the print cartridges by using the control panel or the software you installed with the HP All-in-
One.
132 Maintain the HP All-in-One
Make sure you have the following materials available:
• Dry foam rubber swabs, lint-free cloth, or any soft material that will not come apart or leave fibers.
TIP:
Coffee filters are lint-free and work well for cleaning print cartridges.
• Distilled, filtered, or bottled water (tap water might contain contaminants that can damage the print cartridges).
CAUTION:
Do not touch the copper-colored contacts or ink nozzles. Touching these parts can result in clogs, ink failure, and bad electrical connections.
To clean the area around the ink nozzles
1.
Turn on the HP All-in-One and open the print cartridge door.
The print carriage moves to the far right side of the HP All-in-One.
2.
Wait until the print carriage is idle and silent, and then unplug the power cord from the back of the HP All-in-One.
NOTE:
Depending how long the HP All-in-One is unplugged, the date and time might be erased. You might need to reset the date and time later, when you plug the power cord back in.
3.
Lightly press down on the print cartridge to release it, and then pull it toward you out of the slot.
NOTE:
Do not remove both print cartridges at the same time. Remove and clean each print cartridge one at a time. Do not leave a print cartridge outside the HP Allin-One for more than 30 minutes.
4.
Place the print cartridge on a piece of paper with the ink nozzles facing up.
5.
Lightly moisten a clean foam rubber swab with distilled water.
6.
Clean the face and edges around the ink nozzle area with the swab, as shown below.
1 Nozzle plate (do not clean)
2 Face and edges around the ink nozzle area
CAUTION:
Do not clean the nozzle plate.
7.
Slide the print cartridge back into the slot. Push the print cartridge forward until it clicks into place.
Work with print cartridges 133
Chapter 10
8.
Repeat if necessary for the other print cartridge.
9.
Gently close the print cartridge door and plug the power cord into the back of the
HP All-in-One.
Related topics
134 Maintain the HP All-in-One
11 Troubleshooting
This section contains the following topics:
•
•
•
•
•
•
•
•
Troubleshooting tips
This section contains the following topics:
•
The HP All-in-One will not turn on
•
Communication problems over a USB connection
•
Information on print cartridges
•
•
Tips for using the automatic document feeder
•
•
Print cartridge troubleshooting
The HP All-in-One will not turn on
Cause: The HP All-in-One is not properly connected to a power supply.
Troubleshooting 135
Chapter 11
Solution:
• Make sure the power cord is firmly connected to both the HP All-in-One and the power adapter. Plug the power cord into a grounded power outlet, surge protector, or power strip.
1 Power connection
2 Power cord and adapter
3 Grounded power outlet
• If you are using a power strip, make sure the power strip is on. Or, try plugging the HP All-in-One directly into a grounded power outlet.
• Test the power outlet to make sure it is working. Plug in an appliance that you know works, and see if the appliance has power. If not, then there might be a problem with the power outlet.
• If you plugged the HP All-in-One into a switched outlet, make sure the switch is on. If it is switched to on but still does not work, then there might be a problem with the power outlet.
Cause: You pressed the Power button too quickly.
Solution: The HP All-in-One might not respond if you press the Power button too quickly. Press the Power button once. It might take a few minutes for the HP All-in-
One to turn on. If you press the Power button again during this time, you might turn the device off.
CAUTION:
If the HP All-in-One still does not turn on, it might have a mechanical failure. Unplug the HP All-in-One from the power outlet and contact HP. Go to: www.hp.com/support . If prompted, choose your country/region, and then click
Contact HP for information on calling for technical support.
136 Troubleshooting
Communication problems over a USB connection
If the HP All-in-One and computer are not communicating with each other, try the following:
• Look at the display on the HP All-in-One. If the display is blank and the Power button is not lit, the HP All-in-One is turned off. Make sure the power cord is firmly connected to the HP All-in-One and plugged into a power outlet. Press the Power button to turn on the HP All-in-One.
• Check the USB cable. If you are using an older cable, it might not be working properly.
Try connecting it to another product to see if the USB cable works. If you experience problems, the USB cable might need to be replaced. Also verify that the cable does not exceed 3 meters (9.8 feet) in length.
• Check the connection from the HP All-in-One to your computer. Verify that the USB cable is securely plugged into the USB port on the back of the HP All-in-One. Make sure the other end of the USB cable is plugged into a USB port on your computer.
After the cable is connected properly, turn the HP All-in-One off and then on again.
• Check the System Profiler to verify your USB connection. If the HP All-in-One shows up in the USB window, then the USB connection between your computer and HP Allin-One is working. If it is working, there might be a problem with the software. Use the Setup Assistant that came with your HP Photosmart Studio (Mac) Software to see if it can detect the HP All-in-One. Refer to the help provided with your operating system for instructions on accessing the System Profiler.
• If you are connecting the HP All-in-One through a USB hub, make sure the hub is turned on. If the hub is on, try connecting directly to your computer.
• Check other printers or scanners. You might need to disconnect older products from your computer.
• Try connecting the USB cable to another USB port on your computer. After you check the connections, try restarting your computer. Turn the HP All-in-One off and then on again.
• If necessary, remove and then install the software you installed with the HP All-in-
One again.
Troubleshooting tips 137
Chapter 11
For more information on setting up the HP All-in-One and connecting it to your computer, see the Setup Poster that came with the HP All-in-One.
Information on print cartridges
For best results, use HP print cartridges. The following tips help maintain HP print cartridges and ensure consistent print quality.
• Keep all print cartridges in the original sealed packages until they are needed.
• Store print cartridges at room temperature (15.6°-26.6° C or 60°-78° F).
• Do not reattach the protective tape once it has been removed from the print cartridge.
Reattaching the plastic tape might damage the print cartridge. Place the print cartridge in the HP All-in-One immediately after removing the plastic tape. If this is not possible, store it in a print cartridge protector or airtight plastic container.
• HP recommends that you do not remove the print cartridges from the HP All-in-One until you have replacement print cartridges available to install.
• Turn off the HP All-in-One from the control panel. Do not turn off the device by turning off a power strip or unplugging the power cord from the HP All-in-One. If you improperly turn off the HP All-in-One, the print carriage does not return to the correct position and the print cartridges can dry out.
• Do not open the print cartridge door unless necessary. This exposes the print cartridges to air, which reduces the life of the print cartridges.
NOTE:
If you leave the print cartridge door open for a long period of time, the
HP All-in-One will recap the print cartridges to protect them from exposure to air.
• Clean the print cartridges when you notice a significant decrease in print quality.
TIP:
You might notice a decrease in print quality if the print cartridges have not been used for a long time.
• Do not clean the print cartridges unnecessarily. This wastes ink and shortens the life of the cartridges.
For more information on print cartridges, see Print cartridge troubleshooting .
Information on paper
The HP All-in-One is designed to work well with most paper types. Test a variety of paper types before buying a large quantity. Find a paper type that works well and is easy to purchase. HP Premium papers are designed for the best quality results. In addition, follow these tips:
• Do not use paper that is too thin, that has a slick texture, or that stretches easily. It can feed incorrectly through the paper path, causing paper jams.
• Store photo media in its original packaging inside a resealable plastic bag on a flat surface in a cool, dry place. When you are ready to print, remove only the paper you plan to use immediately. When you have finished printing, return any unused photo paper to the plastic bag.
• Do not leave unused photo paper in the input tray. The paper might start to curl, which might reduce the quality of your printouts. Curled paper can also cause paper jams.
138 Troubleshooting
• Always hold photo paper by the edges. Fingerprints on photo paper can reduce print quality.
• Do not use paper that is heavily textured. It can cause graphics or text to print improperly.
• Do not combine different paper types and paper sizes in the input tray; the entire stack of paper in the input tray must be the same size and type.
• Store printed photos under glass or in a storage book to prevent bleeding over time from high humidity. Use HP Premium Plus photo paper for maximum performance.
Tips for using the automatic document feeder
Follow these simple suggestions to avoid common problems when using the automatic document feeder.
• Remove any staples or clips from the original document.
• Make sure the paper is not too thick or too thin for the HP All-in-One to process.
• Do not overload the document feeder tray. The document feeder tray can hold up to
20 sheets of letter or A4 paper, or up to 15 sheets of legal paper.
• Do not use spiral or frayed paper. If you must use paper that has been removed from a spiral binder, trim the edges.
• Do not load photos in the automatic document feeder. The automatic document feeder can damage photos. Always place photos on the glass to scan or copy.
• Make sure the paper-width guides in the document feeder tray fit snugly against the paper without bending the paper.
• Load your originals print side up into the document feeder tray.
Clear paper jams
If the paper was loaded in the input tray, you might need to clear the paper jam from the rear door.
Paper can also jam in the automatic document feeder. Several common actions can cause paper to jam the automatic document feeder:
• Placing too much paper in the document feeder tray. For information on the maximum number of sheets allowed in the automatic document feeder, see
• Using paper that is too thick or too thin for the HP All-in-One.
• Trying to add paper to the document feeder tray while the HP All-in-One is feeding pages.
To clear a paper jam from the rear door
1.
Press in the tab on the left side of the rear door to release the door. Remove the door by pulling it away from the HP All-in-One.
CAUTION:
Trying to clear a paper jam from the front of the HP All-in-One can damage the print mechanism. Always access and clear paper jams through the rear door.
Troubleshooting tips 139
Chapter 11
2.
Gently pull the paper out of the rollers.
CAUTION:
If the paper tears when you are removing it from the rollers, check the rollers and wheels for torn pieces of paper that might be remaining inside the device. If you do not remove all the pieces of paper from the HP All-in-One, more paper jams are likely to occur.
3.
Replace the rear door. Gently push the door forward until it snaps into place.
4.
Press OK to continue the current job.
To clear a paper jam in the automatic document feeder
1.
Lift the cover of the automatic document feeder.
2.
Gently pull the paper out of the rollers.
CAUTION:
If the paper tears when you are removing it from the rollers, check the rollers and wheels for torn pieces of paper that might be remaining inside the device. If you do not remove all the pieces of paper from the HP All-in-One, more paper jams are likely to occur.
3.
Close the cover of the automatic document feeder.
140 Troubleshooting
Print cartridge troubleshooting
If you are experiencing problems with printing, you might have a problem with one of the print cartridges.
To troubleshoot print cartridges
1.
Remove the black print cartridge from the slot on the right. Do not touch the ink nozzles or the copper-colored contacts. Check for possible damage to the coppercolored contacts or ink nozzles.
Make sure the plastic tape has been removed. If it is still covering the ink nozzles, gently remove the plastic tape by using the pink pull tab.
2.
Reinsert the print cartridge by sliding it forward into the slot. Then push the print cartridge forward until it clicks into the socket.
3.
Repeat steps 1 and 2 for the tri-color print cartridge on the left side.
4.
If the problem persists, print a self-test report to determine if there is a problem with the print cartridges.
This report provides useful information about your print cartridges, including status information.
5.
If the self-test report shows a problem, clean the print cartridges.
6.
If the problem persists, clean the copper-colored contacts of the print cartridges with a lint-free cloth, slightly damp; use distilled water.
7.
If you are still experiencing problems with printing, determine which print cartridge is experiencing the problem and replace it.
For more information, see:
•
•
•
•
Clean the print cartridge contacts
Print quality troubleshooting
This section contains the following topics:
•
•
The automatic document feeder picks up too many pages or none at all
Print quality troubleshooting 141
Chapter 11
•
Ink is not filling the text or graphics completely
•
•
The printout has a horizontal band of distortion near the bottom of the page
•
Colors run into each other on the printout
•
Printouts have horizontal streaks or lines
•
Printouts are faded or have dull colors
•
Printouts seem blurry or fuzzy
•
Printouts have vertical streaks
•
Printouts are slanted or skewed
•
The print quality of the fax I received is poor
•
Some of the pages of a fax I received are faded or blank
•
Ink is overspraying the paper when I copy or print a photo
•
Paper is not picked up from the input tray
Ink is bleeding or smearing
Cause: The paper type is not suitable for the HP All-in-One.
Solution: Use HP Premium Papers or any other paper type that is appropriate for the HP All-in-One.
Cause: The print cartridges need to be cleaned.
Solution: Print a self-test report to determine if there is a problem with the print cartridges. If the self-test report shows a problem, clean the print cartridges. If the problem persists, you might need to replace the print cartridges.
For more information on print cartridges, see Print cartridge troubleshooting .
Cause: The paper is too close to the print cartridge during printing.
Solution: If the paper is too close to the print cartridge during printing, the ink might be smeared. This can happen if the paper is raised, wrinkled, or very thick, such as a mailing envelope. Make sure the paper lays flat in the input tray and is not too wrinkled.
The automatic document feeder picks up too many pages or none at all
Cause: The separator pad or rollers inside the automatic document feeder might need to be cleaned. Pencil lead, wax, or ink can build up on the rollers and separator pad after extensive use, or if you copy handwritten originals or originals that are heavy with ink.
• If the automatic document feeder does not pick up any pages at all, the rollers inside the automatic document feeder need to be cleaned.
• If the automatic document feeder picks up multiple pages instead of single sheets, the separator pad inside the automatic document feeder needs to be cleaned.
Solution: Load one or two sheets of unused plain white full-size paper into the document feeder tray and press Start Copy Black. As the plain paper passes through the automatic document feeder, the paper releases and absorbs residue from the rollers and separator pad.
142 Troubleshooting
TIP:
If the automatic document feeder does not pick up the plain paper, try cleaning the front roller. Wipe the roller with a soft lint-free cloth dampened with distilled water.
If the problem persists, or the automatic document feeder does not pick up the plain paper, you can clean the rollers and separator pad manually.
For more information, see
Clean the automatic document feeder .
Ink is not filling the text or graphics completely
Cause: The print cartridges need to be cleaned or might be out of ink.
Solution: Check the estimated ink levels remaining in the print cartridges. If the print cartridges are low or out of ink, you might need to replace the print cartridges.
If there is ink remaining in the print cartridges, but you are still noticing a problem, print a self-test report to determine if there is a problem with the print cartridges. If the self-test report shows a problem, clean the print cartridges. If the problem persists, you might need to replace the print cartridges.
For more information on print cartridges, see Print cartridge troubleshooting .
Cause: The Paper Type setting is incorrect.
Solution: Change the Paper Type setting to match the type of paper loaded in the input tray.
To set the paper type for copies
1.
In the Copy area, press Menu repeatedly until Paper Type appears.
2.
Press until the appropriate paper type appears.
3.
Press Start Copy Black or Start Copy Color.
To set the paper type for printing
1.
Make sure you have paper loaded in the input tray.
2.
From the File menu in your software application, choose Print.
3.
Make sure the HP All-in-One is the selected printer.
4.
From the pop-up menu, choose Paper Type/Quality.
5.
Click the Paper tab.
6.
From the Paper type pop-up menu, choose the type of paper loaded in the input tray.
Cause: The print or copy quality setting on the HP All-in-One is set too low.
Print quality troubleshooting 143
Chapter 11
Solution: Check the quality setting. Use a higher quality setting to increase the amount of ink used for printing or copying.
To change the print speed or quality
1.
Make sure you have paper loaded in the input tray.
2.
From the File menu in your software application, choose Print.
3.
Make sure the HP All-in-One is the selected printer.
4.
From the pop-up menu, choose Paper Type/Quality.
5.
Click the Paper tab.
6.
From the Paper type pop-up menu, choose the type of paper loaded in the input tray.
7.
From the Quality pop-up menu, choose the appropriate quality setting for your project.
To change the copy quality
1.
Make sure you have paper loaded in the input tray.
2.
Load your original print side down on the right front corner of the glass or print side up in the document feeder tray.
If you use the document feeder tray, place the pages so that the top edge of the document goes in first.
3.
In the Copy area, press Quality until the appropriate quality setting is lit.
4.
Press Start Copy Black or Start Copy Color.
The text edges are jagged
Cause: The font is a custom size.
Solution: Some software applications offer custom fonts that have jagged edges when enlarged or printed. Also, if you want to print bitmapped text, it might have jagged edges when enlarged or printed.
The printout has a horizontal band of distortion near the bottom of the page
Cause: Your image has light blue, gray, or brown hues that print near the bottom of the page.
Solution: Load high-quality paper in the input tray and print the image with a high print quality setting, such as Best, Maximum dpi, or High Resolution. Always make sure the paper you are printing on is flat. For best results when printing images, use HP Premium Plus Photo Paper.
If the problem persists, use the software you installed with the HP All-in-One or another software application to rotate your image 180 degrees so that the light blue, gray, or brown hues in your image do not print at the bottom of the page. Print the image using six-ink printing. To do so, install the photo print cartridge in place of the black print cartridge. With the photo print cartridge and the tri-color print cartridge installed, you have a six-ink system, which provides enhanced quality photos.
For more information on print cartridges, see Print cartridge troubleshooting .
144 Troubleshooting
For more information on paper, see
Understand specifications for supported media .
Colors run into each other on the printout
Cause: The print or copy quality setting is set too high for the type of paper loaded in the HP All-in-One.
Solution: Check the quality setting. Use a lower quality setting to decrease the amount of ink used for printing or copying.
To change the print speed or quality
1.
Make sure you have paper loaded in the input tray.
2.
From the File menu in your software application, choose Print.
3.
Make sure the HP All-in-One is the selected printer.
4.
From the pop-up menu, choose Paper Type/Quality.
5.
Click the Paper tab.
6.
From the Paper type pop-up menu, choose the type of paper loaded in the input tray.
7.
From the Quality pop-up menu, choose the appropriate quality setting for your project.
To change the copy quality
1.
Make sure you have paper loaded in the input tray.
2.
Load your original print side down on the right front corner of the glass or print side up in the document feeder tray.
If you use the document feeder tray, place the pages so that the top edge of the document goes in first.
3.
In the Copy area, press Quality until the appropriate quality setting is lit.
4.
Press Start Copy Black or Start Copy Color.
Cause: The paper type is not suitable for the HP All-in-One.
Solution: Use HP Premium Papers or any other paper type that is appropriate for the HP All-in-One.
For more information on choosing paper, see
Understand specifications for supported media .
Cause: You are printing on the wrong side of the paper.
Solution: Load the paper with the print side down. For example, if you are loading glossy photo paper, load the paper with the glossy side down.
Cause: You are using non-HP ink.
Solution: HP recommends that you use genuine HP print cartridges. Genuine HP print cartridges are designed and tested with HP printers to help you easily produce great results, time after time.
Print quality troubleshooting 145
Chapter 11
NOTE:
HP cannot guarantee the quality or reliability of non-HP ink. Printer service or repairs required as a result of printer failure or damage attributable to the use of non-HP ink will not be covered under warranty.
Cause: The print cartridges need to be cleaned.
Solution: Print a self-test report to determine if there is a problem with the print cartridges. If the self-test report shows a problem, clean the print cartridges. If the problem persists, you might need to replace the print cartridges.
For more information on print cartridges, see Print cartridge troubleshooting .
Printouts have horizontal streaks or lines
Cause: The paper is not feeding properly or is loaded incorrectly.
Solution: Make sure you have paper loaded correctly.
To load full-size paper
1.
Remove the output tray.
2.
Slide the paper-width guide to its outermost position.
3.
Tap a stack of paper on a flat surface to align the edges, and then check the paper for the following:
• Make sure it is free of rips, dust, wrinkles, and curled or bent edges.
• Make sure all the paper in the stack is the same size and type.
146 Troubleshooting
4.
Insert the stack of paper into the input tray with the short edge forward and the print side down. Slide the stack of paper forward until it stops.
CAUTION:
Make sure that the HP All-in-One is idle and silent when you load paper into the input tray. If the HP All-in-One is servicing the print cartridges or otherwise engaged in a task, the paper stop inside the device might not be in place. You could push the paper too far forward, causing the HP All-in-One to eject blank pages.
TIP:
If you are using letterhead, insert the top of the page first with the print side down. For more help on loading full-size paper and letterhead, refer to the diagram engraved in the base of the input tray.
5.
Slide the paper-width guide inward until it stops at the edge of the paper.
Do not overload the input tray; make sure the stack of paper fits within the input tray and is no higher than the top of the paper-width guide.
6.
Replace the output tray.
Print quality troubleshooting 147
Chapter 11
7.
Flip the tray extender up toward you.
NOTE:
When you use legal-size paper, leave the tray extender closed.
Cause: The print or copy quality setting on the HP All-in-One is set too low.
Solution: Check the quality setting. Use a higher quality setting to increase the amount of ink used for printing or copying.
To change the print speed or quality
1.
Make sure you have paper loaded in the input tray.
2.
From the File menu in your software application, choose Print.
3.
Make sure the HP All-in-One is the selected printer.
4.
From the pop-up menu, choose Paper Type/Quality.
5.
Click the Paper tab.
6.
From the Paper type pop-up menu, choose the type of paper loaded in the input tray.
7.
From the Quality pop-up menu, choose the appropriate quality setting for your project.
To change the copy quality
1.
Make sure you have paper loaded in the input tray.
2.
Load your original print side down on the right front corner of the glass or print side up in the document feeder tray.
If you use the document feeder tray, place the pages so that the top edge of the document goes in first.
3.
In the Copy area, press Quality until the appropriate quality setting is lit.
4.
Press Start Copy Black or Start Copy Color.
Cause: The print cartridges need to be cleaned or might be out of ink.
Solution: Check the estimated ink levels remaining in the print cartridges. If the print cartridges are low or out of ink, you might need to replace the print cartridges.
If there is ink remaining in the print cartridges, but you are still noticing a problem, print a self-test report to determine if there is a problem with the print cartridges. If the self-test report shows a problem, clean the print cartridges. If the problem persists, you might need to replace the print cartridges.
148 Troubleshooting
For more information on print cartridges, see Print cartridge troubleshooting .
Cause: There might be fiber or dust built up around the ink nozzle area on the print cartridges.
Solution: Check the print cartridges. If it looks as though there are fibers or dust around the ink nozzles, clean the ink nozzle area of the print cartridge.
To clean the area around the ink nozzles
1.
Turn on the HP All-in-One and open the print cartridge door.
The print carriage moves to the far right side of the HP All-in-One.
2.
Wait until the print carriage is idle and silent, and then unplug the power cord from the back of the HP All-in-One.
NOTE:
Depending how long the HP All-in-One is unplugged, the date and time might be erased. You might need to reset the date and time later, when you plug the power cord back in.
3.
Lightly press down on the print cartridge to release it, and then pull it toward you out of the slot.
NOTE:
Do not remove both print cartridges at the same time. Remove and clean each print cartridge one at a time. Do not leave a print cartridge outside the HP All-in-One for more than 30 minutes.
4.
Place the print cartridge on a piece of paper with the ink nozzles facing up.
5.
Lightly moisten a clean foam rubber swab with distilled water.
6.
Clean the face and edges around the ink nozzle area with the swab, as shown below.
1 Nozzle plate (do not clean)
2 Face and edges around the ink nozzle area
CAUTION:
Do not clean the nozzle plate.
7.
Slide the print cartridge back into the slot. Push the print cartridge forward until it clicks into place.
Print quality troubleshooting 149
Chapter 11
8.
Repeat if necessary for the other print cartridge.
9.
Gently close the print cartridge door and plug the power cord into the back of the
HP All-in-One.
Cause: The sending fax machine is having problems.
Solution: Ask the sender to check their fax machine for any problems.
Cause: The phone line connection is noisy. Phone lines with poor sound quality
(noise) can cause print quality problems.
Solution: If the failure was due to noise on the phone line, contact the sender to have them resend the fax. The quality might be better when you try again. You can check the sound quality of the phone line by plugging a phone into the telephone wall jack and listening for static or other noise. If the problem persists, turn Error
Correction Mode (ECM) off and contact your telephone company.
To change the ECM setting from the control panel
1.
Press Setup.
2.
Press 5, and then press 6.
This selects Advanced Fax Setup and then selects Error Correction Mode.
3.
Press to select On or Off.
4.
Press OK.
Printouts are faded or have dull colors
Cause: The print cartridges need to be cleaned or might be out of ink.
Solution: Check the estimated ink levels remaining in the print cartridges. If the print cartridges are low or out of ink, you might need to replace the print cartridges.
If there is ink remaining in the print cartridges, but you are still noticing a problem, print a self-test report to determine if there is a problem with the print cartridges. If the self-test report shows a problem, clean the print cartridges. If the problem persists, you might need to replace the print cartridges.
For more information on print cartridges, see Print cartridge troubleshooting .
Cause: The print or copy quality setting on the HP All-in-One is set too low.
Solution: Check the quality setting. Use a higher quality setting to increase the amount of ink used for printing or copying.
To change the copy quality
1.
Make sure you have paper loaded in the input tray.
2.
Load your original print side down on the right front corner of the glass or print side up in the document feeder tray.
If you use the document feeder tray, place the pages so that the top edge of the document goes in first.
150 Troubleshooting
3.
In the Copy area, press Quality until the appropriate quality setting is lit.
4.
Press Start Copy Black or Start Copy Color.
To change the print speed or quality
1.
Make sure you have paper loaded in the input tray.
2.
From the File menu in your software application, choose Print.
3.
Make sure the HP All-in-One is the selected printer.
4.
From the pop-up menu, choose Paper Type/Quality.
5.
Click the Paper tab.
6.
From the Paper type pop-up menu, choose the type of paper loaded in the input tray.
7.
From the Quality pop-up menu, choose the appropriate quality setting for your project.
For more information about changing quality settings, see the HP Officejet J5700 Allin-One series Help section in the HP Photosmart Software Help.
Cause: The paper type is not suitable for the HP All-in-One.
Solution: If the paper you are using is too fibrous, the ink applied by the HP All-in-
One might not fully cover the surface of the paper. Use HP Premium Papers or any other paper type that is appropriate for the HP All-in-One.
For more information on choosing paper, see
Understand specifications for supported media .
Cause: The Lighter / Darker copy setting for the HP All-in-One is set too light.
Solution: Adjust the lightness and darkness of the copies.
To adjust the copy contrast from the control panel
1.
Make sure you have paper loaded in the input tray.
2.
Load your original print side down on the right front corner of the glass or print side up in the document feeder tray.
If you use the document feeder tray, place the pages so that the top edge of the document goes in first.
3.
In the Copy area, press Menu repeatedly until Lighter / Darker appears.
4.
Do one of the following:
• Press to darken the copy.
• Press to lighten the copy.
5.
Press Start Copy Black or Start Copy Color.
Cause: The Paper Type setting is incorrect.
Print quality troubleshooting 151
Chapter 11
Solution: Change the Paper Type setting to match the type of paper loaded in the input tray.
To set the paper type for copies
1.
In the Copy area, press Menu repeatedly until Paper Type appears.
2.
Press until the appropriate paper type appears.
3.
Press Start Copy Black or Start Copy Color.
To set the paper type for printing
1.
Make sure you have paper loaded in the input tray.
2.
From the File menu in your software application, choose Print.
3.
Make sure the HP All-in-One is the selected printer.
4.
From the pop-up menu, choose Paper Type/Quality.
5.
Click the Paper tab.
6.
From the Paper type pop-up menu, choose the type of paper loaded in the input tray.
Cause: Copying a poor-quality picture, such as a newspaper photo, causes bands, checks, or stripes to appear on your copy. These are called moiré patterns.
Solution: To reduce moiré patterns, try placing one or more clear plastic sheet protectors directly on the glass, and then place the original print side down on top of the sheet protectors.
Cause: Debris might be stuck on the glass or on the back of the document lid; this causes poor copy quality and slows down processing.
Solution:
To clean the glass
1.
Turn off the HP All-in-One, and raise the lid.
2.
Clean the glass with a soft cloth or sponge slightly moistened with a nonabrasive glass cleaner.
CAUTION:
Do not use abrasives, acetone, benzene, or carbon tetrachloride on the glass, since they can damage it. Do not place or spray liquid directly on the glass. The liquid might seep under the glass and damage the device.
3.
Dry the glass with a dry, soft, lint-free cloth to prevent spotting.
4.
Turn on the HP All-in-One.
152 Troubleshooting
To clean the lid backing
1.
Turn off the HP All-in-One, unplug the power cord, and raise the lid.
NOTE:
Depending how long the HP All-in-One is unplugged, the date and time might be erased. You might need to reset the date and time later, when you plug the power cord back in.
2.
Clean the white document backing with a soft cloth or sponge slightly moistened with a mild soap and warm water.
Wash the backing gently to loosen debris. Do not scrub the backing.
3.
Dry the backing with a dry, soft, lint-free cloth.
CAUTION:
Do not use paper-based wipes, as these might scratch the backing.
4.
If further cleaning is needed, repeat the previous steps using isopropyl (rubbing) alcohol, and wipe the backing thoroughly with a damp cloth to remove any residual alcohol.
CAUTION:
Be careful not to spill alcohol on the glass or exterior of the HP Allin-One, as this might damage the device.
Printouts seem blurry or fuzzy
Cause: The fax sender is using a low resolution or the original was poor quality.
Solution: Ask the sender to increase the resolution and to verify the quality of the original.
Cause: The paper loaded in the input tray is not suitable for the HP All-in-One.
Solution: If the paper you are using is too fibrous, the ink applied by the HP All-in-
One might not fully cover the surface of the paper. Use HP Premium Papers or any other paper type that is appropriate for the HP All-in-One.
For more information on choosing paper, see
Understand specifications for supported media .
Cause: The Paper Type copy or print setting is incorrect.
Solution: Change the Paper Type setting to match the type of paper loaded in the input tray.
To set the paper type for copies
1.
In the Copy area, press Menu repeatedly until Paper Type appears.
2.
Press until the appropriate paper type appears.
3.
Press Start Copy Black or Start Copy Color.
Print quality troubleshooting 153
Chapter 11
To set the paper type for printing
1.
Make sure you have paper loaded in the input tray.
2.
From the File menu in your software application, choose Print.
3.
Make sure the HP All-in-One is the selected printer.
4.
From the pop-up menu, choose Paper Type/Quality.
5.
Click the Paper tab.
6.
From the Paper type pop-up menu, choose the type of paper loaded in the input tray.
Cause: The print or copy quality setting on the HP All-in-One is set too low.
Solution: Check the quality setting. Use a higher quality setting to increase the amount of ink used for printing or copying.
To change the print speed or quality
1.
Make sure you have paper loaded in the input tray.
2.
From the File menu in your software application, choose Print.
3.
Make sure the HP All-in-One is the selected printer.
4.
From the pop-up menu, choose Paper Type/Quality.
5.
Click the Paper tab.
6.
From the Paper type pop-up menu, choose the type of paper loaded in the input tray.
7.
From the Quality pop-up menu, choose the appropriate quality setting for your project.
To change the copy quality
1.
Make sure you have paper loaded in the input tray.
2.
Load your original print side down on the right front corner of the glass or print side up in the document feeder tray.
If you use the document feeder tray, place the pages so that the top edge of the document goes in first.
3.
In the Copy area, press Quality until the appropriate quality setting is lit.
4.
Press Start Copy Black or Start Copy Color.
Cause: You are printing on the wrong side of the paper.
Solution: Load paper with the print side down. For example, if you are loading glossy photo paper, load the paper with the glossy side down.
Printouts have vertical streaks
Cause: The paper type is not suitable for the HP All-in-One.
Solution: If the paper you are using is too fibrous, the ink applied by the HP All-in-
One might not fully cover the surface of the paper. Use HP Premium Papers or any other paper type that is appropriate for the HP All-in-One.
154 Troubleshooting
For more information on choosing paper, see
Understand specifications for supported media .
Cause: The glass or automatic document feeder of the sending fax machine is dirty.
Solution: If you have vertical lines or streaks on the fax, the sender's fax machine might have dirt or dust on the glass or automatic document feeder. Check with the sender to see if the glass or automatic document feeder is clean.
Printouts are slanted or skewed
Cause: The paper is not feeding properly or is loaded incorrectly.
Solution: Make sure the paper is loaded correctly.
To load full-size paper
1.
Remove the output tray.
2.
Slide the paper-width guide to its outermost position.
3.
Tap a stack of paper on a flat surface to align the edges, and then check the paper for the following:
• Make sure it is free of rips, dust, wrinkles, and curled or bent edges.
• Make sure all the paper in the stack is the same size and type.
Print quality troubleshooting 155
Chapter 11
4.
Insert the stack of paper into the input tray with the short edge forward and the print side down. Slide the stack of paper forward until it stops.
CAUTION:
Make sure that the HP All-in-One is idle and silent when you load paper into the input tray. If the HP All-in-One is servicing the print cartridges or otherwise engaged in a task, the paper stop inside the device might not be in place. You could push the paper too far forward, causing the HP All-in-One to eject blank pages.
TIP:
If you are using letterhead, insert the top of the page first with the print side down. For more help on loading full-size paper and letterhead, refer to the diagram engraved in the base of the input tray.
5.
Slide the paper-width guide inward until it stops at the edge of the paper.
Do not overload the input tray; make sure the stack of paper fits within the input tray and is no higher than the top of the paper-width guide.
6.
Replace the output tray.
156 Troubleshooting
7.
Flip the tray extender up toward you.
NOTE:
When you use legal-size paper, leave the tray extender closed.
Cause: The original might have been loaded incorrectly into the sending fax machine.
Solution: Ask the sender to check that the fax was sent correctly.
Cause: More than one type of paper is loaded in the input tray.
Solution: Load only one type of paper at a time. When you are printing faxes, make sure letter, A4, or legal paper is loaded in the input tray.
The print quality of the fax I received is poor
Cause: The phone line connection is noisy.
Solution: If the failure was due to noise on the phone line, contact the sender to have them resend the fax. The quality might be better when you try again. You can check the sound quality of the phone line by plugging a phone into the telephone wall jack and listening for static or other noise. If the problem persists, turn Error
Correction Mode (ECM) off and contact your telephone company.
To change the ECM setting from the control panel
1.
Press Setup.
2.
Press 5, and then press 6.
This selects Advanced Fax Setup and then selects Error Correction Mode.
3.
Press to select On or Off.
4.
Press OK.
Cause: The sending fax machine is having problems.
Solution: Ask the sender to check the sending fax machine for any problems. Also check to see if faxes from other senders have the same quality problems.
Cause: The glass or automatic document feeder of the sending fax machine is dirty.
Print quality troubleshooting 157
Chapter 11
Solution: If you have vertical lines or streaks on the fax, the sender's fax machine might have dirt or dust on the glass or automatic document feeder. Check with the sender to see if the glass or automatic document feeder is clean.
Cause: The print cartridges need to be cleaned or might be out of ink.
Solution: Check the estimated ink levels remaining in the print cartridges. If the print cartridges are low or out of ink, you might need to replace the print cartridges.
If there is ink remaining in the print cartridges, but you are still noticing a problem, print a self-test report to determine if there is a problem with the print cartridges. If the self-test report shows a problem, clean the print cartridges. If the problem persists, you might need to replace the print cartridges.
For more information on print cartridges, see Print cartridge troubleshooting .
Some of the pages of a fax I received are faded or blank
Cause: The print cartridges need to be cleaned or might be out of ink.
Solution: Check the estimated ink levels remaining in the print cartridges. If the print cartridges are low or out of ink, you might need to replace the print cartridges.
If there is ink remaining in the print cartridges, but you are still noticing a problem, print a self-test report to determine if there is a problem with the print cartridges. If the self-test report shows a problem, clean the print cartridges. If the problem persists, you might need to replace the print cartridges.
For more information on print cartridges, see Print cartridge troubleshooting .
Cause: The sender incorrectly loaded the originals in the sending fax machine.
Solution: Check with the sender to see if they correctly loaded the originals in the sending fax machine or accidentally sent a blank page.
Cause: The HP All-in-One picked up two sheets of paper while printing the fax.
Solution: If the HP All-in-One has only a few sheets remaining, load more paper in the input tray. If there is plenty of paper in the input tray, remove the paper, tap the stack of paper against a flat surface, and reload the paper into the input tray.
Cause: The paper loaded in the input tray is not suitable for your fax.
Solution: If the paper you are using is too fibrous, the ink applied by the HP All-in-
One might not fully cover the surface of the paper. Use HP Premium Papers or any other paper type that is appropriate for the HP All-in-One.
For more information on choosing paper, see
Understand specifications for supported media .
158 Troubleshooting
Ink is overspraying the paper when I copy or print a photo
Cause: A small amount (a few millimeters) of overspray is common when making a copy of a photo. If there are more than a few millimeters of overspray, it might mean the HP All-in-One thinks the paper loaded is wider than it actually is.
TIP:
One way to tell if ink is overspraying the paper is to check the back side of pages you print after running a copy or print job. If the back side of the page has ink streaks, the HP All-in-One might have over sprayed your previous copy or print job.
Solution: Check the paper size setting. Set the paper size to match the paper loaded in the input tray.
To set the paper size from the control panel
1.
In the Copy area, press Menu repeatedly until Copy Paper Size appears.
2.
Press until the appropriate paper size appears.
3.
Press Start Copy Black or Start Copy Color.
Paper is not picked up from the input tray
Cause: There is not enough paper in the input tray.
Solution: If the HP All-in-One is out of paper or there are only a few sheets remaining, load more paper in the input tray. If there is paper in the input tray, remove the paper, tap the stack of paper against a flat surface, and reload the paper into the input tray. To continue your print job, press OK on the control panel of the HP All-in-
One.
Print troubleshooting
Use this section to solve these printing problems:
•
•
Borderless printing produces unexpected results
•
The HP All-in-One is not responding
•
The HP All-in-One prints meaningless characters
•
Nothing happens when I try to print
•
•
The margins are not printing as expected
•
Text or graphics are cut off at the edge of the page
•
A blank page came out while printing
•
Ink is spraying the inside of the HP All-in-One when I print a photo
Envelopes print incorrectly
Cause: A stack of envelopes is loaded incorrectly.
Solution: Remove all paper from the input tray. Load a stack of envelopes in the input tray, with the envelope flaps facing up and on the left.
Print troubleshooting 159
Chapter 11
NOTE:
To avoid paper jams, tuck the flaps inside the envelopes.
To load envelopes
1.
Remove the output tray.
2.
Remove all paper from the input tray.
3.
Insert one or more envelopes into the far-right side of the input tray with the envelope flaps up and on the left. Slide the stack of envelopes forward until it stops.
TIP:
For more help on loading envelopes, refer to the diagram engraved in the base of the input tray.
4.
Slide the paper-width guide inward against the stack of envelopes until it stops.
Do not overload the input tray; make sure the stack of envelopes fits within the input tray and is not higher than the top of the paper-width guide.
5.
Replace the output tray.
Cause: The wrong type of envelopes is loaded.
Solution: Do not use shiny or embossed envelopes or envelopes that have clasps or windows.
Cause: The ink is smearing on the envelope.
160 Troubleshooting
Solution: If the ink smears when printing envelopes, tuck the flaps inside the envelopes. If the problem persists, remove the black print cartridge and print with only the tri-color print cartridge installed.
Borderless printing produces unexpected results
Cause: Printing a borderless image from a non-HP software application produces unexpected results.
Solution: Try printing the image from the photo imaging software that came with the HP All-in-One.
The HP All-in-One is not responding
Cause: The HP All-in-One is busy with another task.
Solution: If the HP All-in-One is performing another task such as copying, faxing, or scanning, your print job will be delayed until the HP All-in-One completes the current task.
Some documents take a long time to print. If nothing has printed several minutes after you sent a print job to the HP All-in-One, check the HP All-in-One display to see if there are any messages.
Cause: The HP All-in-One has a paper jam.
Solution: For information on clearing a paper jam, see
Cause: The HP All-in-One is out of paper.
Solution: Load paper in the input tray.
To load full-size paper
1.
Remove the output tray.
Print troubleshooting 161
Chapter 11
2.
Slide the paper-width guide to its outermost position.
3.
Tap a stack of paper on a flat surface to align the edges, and then check the paper for the following:
• Make sure it is free of rips, dust, wrinkles, and curled or bent edges.
• Make sure all the paper in the stack is the same size and type.
4.
Insert the stack of paper into the input tray with the short edge forward and the print side down. Slide the stack of paper forward until it stops.
162 Troubleshooting
CAUTION:
Make sure that the HP All-in-One is idle and silent when you load paper into the input tray. If the HP All-in-One is servicing the print cartridges or otherwise engaged in a task, the paper stop inside the device might not be in place. You could push the paper too far forward, causing the HP All-in-One to eject blank pages.
TIP:
If you are using letterhead, insert the top of the page first with the print side down. For more help on loading full-size paper and letterhead, refer to the diagram engraved in the base of the input tray.
5.
Slide the paper-width guide inward until it stops at the edge of the paper.
Do not overload the input tray; make sure the stack of paper fits within the input tray and is no higher than the top of the paper-width guide.
6.
Replace the output tray.
7.
Flip the tray extender up toward you.
NOTE:
When you use legal-size paper, leave the tray extender closed.
Cause: The print carriage has stalled.
Solution: Turn the HP All-in-One off, remove any objects that are blocking the print carriage (including any packing materials), and then turn the HP All-in-One on again.
Cause: The computer is not communicating with the HP All-in-One.
Print troubleshooting 163
Chapter 11
Solution: If the HP All-in-One is not properly connected to the computer, communication errors can occur. Make sure the USB cable is connected to the HP Allin-One and the computer as shown below.
You can print a test page from the HP Photosmart Studio (Mac) Software to confirm the connection between the HP All-in-One and your Mac is working properly. This test page is different from the self-test report that you can print from the control panel.
To print a test page
1.
Select the HP Device Manager from the Dock.
The HP Device Manager window appears.
2.
From the Information and Settings drop-down, select Maintain Printer.
3.
Select the HP All-in-One, and then select Launch Utility.
4.
Click Print Test Page.
A test page is printed as long as your connection is set up and working properly.
For information on setting up the HP All-in-One, see the Setup Poster provided with the HP All-in-One.
Cause: The HP All-in-One is turned off.
Solution: Look at the display on the HP All-in-One. If the display is blank and the light next to the Power button is not lit, the HP All-in-One is turned off. Make sure the power cord is firmly connected to the HP All-in-One and plugged into a power outlet.
Press the Power button to turn on the HP All-in-One.
Cause: The HP All-in-One experienced an error.
Solution: Turn the HP All-in-One off, and then unplug the power cord. Plug the power cord back in, and then press the Power button to turn on the HP All-in-One.
NOTE:
Depending how long the HP All-in-One is unplugged, the date and time might be erased. You might need to reset the date and time later, when you plug the power cord back in.
The HP All-in-One prints meaningless characters
Cause: The memory in the HP All-in-One is full.
Solution: Turn off the HP All-in-One and your computer for 60 seconds, then turn them both on and try printing again.
Cause: The document is corrupt.
Solution: Try printing another document from the same software application. If this works, then try printing a previously saved version of the document that is not corrupt.
Nothing happens when I try to print
Cause: The HP All-in-One is turned off.
164 Troubleshooting
Solution: Look at the display on the HP All-in-One. If the display is blank and the light next to the Power button is not lit, the HP All-in-One is turned off. Make sure the power cord is firmly connected to the HP All-in-One and plugged into a power outlet.
Press the Power button to turn on the HP All-in-One.
Cause: The HP All-in-One is busy with another task.
Solution: If the HP All-in-One is performing another task such as copying, faxing, or scanning, your print job will be delayed until the HP All-in-One completes the current task.
Some documents take a long time to print. If nothing has printed several minutes after you sent a print job to the HP All-in-One, check the HP All-in-One display to see if there are any messages.
Cause: The HP All-in-One is not the selected printer.
Solution: Make sure the HP All-in-One is the selected printer in your software application.
Cause: The computer is not communicating with the HP All-in-One.
Solution: If the HP All-in-One is not properly connected to the computer, communication errors can occur. Make sure the USB cable is connected to the HP Allin-One and the computer as shown below.
You can print a test page from the HP Photosmart Studio (Mac) Software to confirm the connection between the HP All-in-One and your Mac is working properly. This test page is different from the self-test report that you can print from the control panel.
To print a test page
1.
Select the HP Device Manager from the Dock.
The HP Device Manager window appears.
2.
From the Information and Settings drop-down, select Maintain Printer.
Print troubleshooting 165
Chapter 11
3.
Select the HP All-in-One, and then select Launch Utility.
4.
Click Print Test Page.
A test page is printed as long as your connection is set up and working properly.
For information on setting up the HP All-in-One, see the Setup Poster provided with the HP All-in-One.
Cause: The HP All-in-One has a paper jam.
Solution: For information on clearing paper jams, see Clear paper jams .
Cause: The print carriage has stalled.
Solution: Turn the HP All-in-One off, remove any objects that are blocking the print carriage (including any packing materials), and then turn the HP All-in-One on again.
Cause: The HP All-in-One is out of paper.
Solution: Load paper in the input tray.
To load full-size paper
1.
Remove the output tray.
2.
Slide the paper-width guide to its outermost position.
166 Troubleshooting
3.
Tap a stack of paper on a flat surface to align the edges, and then check the paper for the following:
• Make sure it is free of rips, dust, wrinkles, and curled or bent edges.
• Make sure all the paper in the stack is the same size and type.
4.
Insert the stack of paper into the input tray with the short edge forward and the print side down. Slide the stack of paper forward until it stops.
CAUTION:
Make sure that the HP All-in-One is idle and silent when you load paper into the input tray. If the HP All-in-One is servicing the print cartridges or otherwise engaged in a task, the paper stop inside the device might not be in place. You could push the paper too far forward, causing the HP All-in-One to eject blank pages.
TIP:
If you are using letterhead, insert the top of the page first with the print side down. For more help on loading full-size paper and letterhead, refer to the diagram engraved in the base of the input tray.
5.
Slide the paper-width guide inward until it stops at the edge of the paper.
Do not overload the input tray; make sure the stack of paper fits within the input tray and is no higher than the top of the paper-width guide.
Print troubleshooting 167
Chapter 11
6.
Replace the output tray.
7.
Flip the tray extender up toward you.
NOTE:
When you use legal-size paper, leave the tray extender closed.
My document did not print
Cause: The input tray is empty or there is a paper jam.
Solution: Make sure paper is loaded in the input tray and that there is no paper jam.
To load full-size paper
1.
Remove the output tray.
168 Troubleshooting
2.
Slide the paper-width guide to its outermost position.
3.
Tap a stack of paper on a flat surface to align the edges, and then check the paper for the following:
• Make sure it is free of rips, dust, wrinkles, and curled or bent edges.
• Make sure all the paper in the stack is the same size and type.
4.
Insert the stack of paper into the input tray with the short edge forward and the print side down. Slide the stack of paper forward until it stops.
CAUTION:
Make sure that the HP All-in-One is idle and silent when you load paper into the input tray. If the HP All-in-One is servicing the print cartridges or otherwise engaged in a task, the paper stop inside the device might not be in place. You could push the paper too far forward, causing the HP All-in-One to eject blank pages.
TIP:
If you are using letterhead, insert the top of the page first with the print side down. For more help on loading full-size paper and letterhead, refer to the diagram engraved in the base of the input tray.
Print troubleshooting 169
Chapter 11
5.
Slide the paper-width guide inward until it stops at the edge of the paper.
Do not overload the input tray; make sure the stack of paper fits within the input tray and is no higher than the top of the paper-width guide.
6.
Replace the output tray.
7.
Flip the tray extender up toward you.
NOTE:
When you use legal-size paper, leave the tray extender closed.
For information on clearing a paper jam, see
.
Cause: The print cartridges might be out of ink.
Solution: Check the estimated ink levels remaining in the print cartridges. If the print cartridges are low or out of ink, you might need to replace the print cartridges.
For more information on print cartridges, see Print cartridge troubleshooting .
170 Troubleshooting
The margins are not printing as expected
Cause: The margins are not set correctly in your software application.
Solution: Check the printer margins.
To check your margin settings
1.
Preview your print job before sending it to the HP All-in-One.
2.
Check the margins.
The HP All-in-One uses the margins you have set in your software application, as long as they are greater than the minimum margins the HP All-in-One supports.
3.
Cancel the print job if the margins are not satisfactory, and then adjust the margins in your software application.
Make sure the margin settings for the document do not exceed the printable area of the HP All-in-One.
Cause: The paper size setting might not be set correctly for the project you are printing.
Solution: Verify that you have selected the proper paper size setting for your project. Make sure that you have loaded the correct paper size in the input tray.
Cause: The paper guides are not positioned correctly.
Solution: Remove the stack of paper from the input tray, and then reload the paper following the steps below.
To load full-size paper
1.
Remove the output tray.
Print troubleshooting 171
Chapter 11
2.
Slide the paper-width guide to its outermost position.
3.
Tap a stack of paper on a flat surface to align the edges, and then check the paper for the following:
• Make sure it is free of rips, dust, wrinkles, and curled or bent edges.
• Make sure all the paper in the stack is the same size and type.
4.
Insert the stack of paper into the input tray with the short edge forward and the print side down. Slide the stack of paper forward until it stops.
172 Troubleshooting
CAUTION:
Make sure that the HP All-in-One is idle and silent when you load paper into the input tray. If the HP All-in-One is servicing the print cartridges or otherwise engaged in a task, the paper stop inside the device might not be in place. You could push the paper too far forward, causing the HP All-in-One to eject blank pages.
TIP:
If you are using letterhead, insert the top of the page first with the print side down. For more help on loading full-size paper and letterhead, refer to the diagram engraved in the base of the input tray.
5.
Slide the paper-width guide inward until it stops at the edge of the paper.
Do not overload the input tray; make sure the stack of paper fits within the input tray and is no higher than the top of the paper-width guide.
6.
Replace the output tray.
7.
Flip the tray extender up toward you.
NOTE:
When you use legal-size paper, leave the tray extender closed.
Cause: A stack of envelopes is loaded incorrectly.
Solution: Remove all paper from the input tray. Load a stack of envelopes in the input tray, with the envelope flaps facing up and on the left.
NOTE:
To avoid paper jams, tuck the flaps inside the envelopes.
Print troubleshooting 173
Chapter 11
Text or graphics are cut off at the edge of the page
Cause: The margins are not set correctly in your software application.
Solution: Make sure the margin settings for the document do not exceed the printable area of the HP All-in-One.
To check your margin settings
1.
Preview your print job before sending it to the HP All-in-One.
2.
Check the margins.
The HP All-in-One uses the margins you have set in your software application, as long as they are greater than the minimum margins the HP All-in-One supports.
3.
Cancel the print job if the margins are not satisfactory, and then adjust the margins in your software application.
Cause: The size of the document you are printing is larger than the paper loaded in the input tray.
Solution: Make sure the layout of the document you are trying to print fits on a paper size supported by the HP All-in-One.
To preview the print layout
1.
Load the correct paper size into the input tray.
2.
Preview your print job before sending it to the HP All-in-One.
3.
Check the graphics in the document to make sure that the current size fits within the printable area of the HP All-in-One.
4.
Cancel the print job if the graphics do not fit in the printable area of the page.
TIP:
Some software applications allow you to scale the document to fit the paper size currently selected. Additionally, you can scale the size of a document from the Page Setup dialog box.
Cause: The paper is loaded incorrectly.
Solution: If the paper is misfeeding, it could cause parts of the document to cut off.
174 Troubleshooting
Remove the stack of paper from the input tray, and then reload the paper following the steps below.
To load full-size paper
1.
Remove the output tray.
2.
Slide the paper-width guide to its outermost position.
3.
Tap a stack of paper on a flat surface to align the edges, and then check the paper for the following:
• Make sure it is free of rips, dust, wrinkles, and curled or bent edges.
• Make sure all the paper in the stack is the same size and type.
Print troubleshooting 175
Chapter 11
4.
Insert the stack of paper into the input tray with the short edge forward and the print side down. Slide the stack of paper forward until it stops.
CAUTION:
Make sure that the HP All-in-One is idle and silent when you load paper into the input tray. If the HP All-in-One is servicing the print cartridges or otherwise engaged in a task, the paper stop inside the device might not be in place. You could push the paper too far forward, causing the HP All-in-One to eject blank pages.
TIP:
If you are using letterhead, insert the top of the page first with the print side down. For more help on loading full-size paper and letterhead, refer to the diagram engraved in the base of the input tray.
5.
Slide the paper-width guide inward until it stops at the edge of the paper.
Do not overload the input tray; make sure the stack of paper fits within the input tray and is no higher than the top of the paper-width guide.
6.
Replace the output tray.
176 Troubleshooting
7.
Flip the tray extender up toward you.
NOTE:
When you use legal-size paper, leave the tray extender closed.
A blank page came out while printing
Cause: If you are printing black text, and a blank page comes out of the HP All-in-
One, the black print cartridge might be empty.
Solution: Check the estimated ink levels remaining in the print cartridges. If the print cartridges are low or out of ink, you might need to replace the print cartridges.
If there is ink remaining in the print cartridges, but you are still noticing a problem, print a self-test report to determine if there is a problem with the print cartridges. If the self-test report shows a problem, clean the print cartridges. If the problem persists, you might need to replace the print cartridges.
For more information, see
Print cartridge troubleshooting .
Cause: The document you are printing contains an additional blank page.
Solution: Open the document file in your software application and remove any extra pages or lines at the end of the document.
Cause: The HP All-in-One picked up two sheets of paper.
Solution: If the HP All-in-One has only a few sheets remaining, load more paper in the input tray. If there is plenty of paper in the input tray, remove the paper, tap the
Print troubleshooting 177
Chapter 11 stack of paper against a flat surface, and reload the paper into the input tray. To continue your print job, press the OK button on the control panel of the HP All-in-One.
To load full-size paper
1.
Remove the output tray.
2.
Slide the paper-width guide to its outermost position.
3.
Tap a stack of paper on a flat surface to align the edges, and then check the paper for the following:
• Make sure it is free of rips, dust, wrinkles, and curled or bent edges.
• Make sure all the paper in the stack is the same size and type.
178 Troubleshooting
4.
Insert the stack of paper into the input tray with the short edge forward and the print side down. Slide the stack of paper forward until it stops.
CAUTION:
Make sure that the HP All-in-One is idle and silent when you load paper into the input tray. If the HP All-in-One is servicing the print cartridges or otherwise engaged in a task, the paper stop inside the device might not be in place. You could push the paper too far forward, causing the HP All-in-One to eject blank pages.
TIP:
If you are using letterhead, insert the top of the page first with the print side down. For more help on loading full-size paper and letterhead, refer to the diagram engraved in the base of the input tray.
5.
Slide the paper-width guide inward until it stops at the edge of the paper.
Do not overload the input tray; make sure the stack of paper fits within the input tray and is no higher than the top of the paper-width guide.
6.
Replace the output tray.
Print troubleshooting 179
Chapter 11
7.
Flip the tray extender up toward you.
NOTE:
When you use legal-size paper, leave the tray extender closed.
Cause: The protective plastic tape was only partially removed from the print cartridge.
Solution: Check each print cartridge. The tape might have been removed from the copper-colored contacts, but still might cover the ink nozzles. If the tape is still covering the ink nozzles, carefully remove the tape from the print cartridges. Do not touch the ink nozzles or the copper-colored contacts.
1 Copper-colored contacts
2 Plastic tape with pink pull tab (must be removed before installing)
3 Ink nozzles under tape
180 Troubleshooting
Ink is spraying the inside of the HP All-in-One when I print a photo
Cause: The borderless print settings require photo paper to be loaded in the input tray. You are using the wrong paper type.
Solution: Make sure you load photo paper in the input tray before you print a borderless print job.
Fax troubleshooting
Use this section to solve the following fax problems:
•
The HP All-in-One is having problems sending and receiving faxes
•
The HP All-in-One cannot send faxes, but can receive faxes
•
The HP All-in-One is having problems sending a manual fax
•
Pages of a fax I sent are missing
•
The quality of the fax I sent is poor
•
Parts of a fax I sent are cut off
•
The fax I sent was blank when it was received
•
•
The HP All-in-One cannot receive faxes, but can send faxes
•
The HP All-in-One is having problems receiving a manual fax
•
Fax tones are recorded on my answering machine
•
The HP All-in-One is not answering incoming fax calls
•
Pages of a fax I received are missing
•
Faxes are received but do not print
•
Parts of a fax I received are cut off
•
The computer to which I am connecting has only one phone port
•
I hear static on my telephone line since connecting the HP All-in-One
•
•
I am having problems faxing over the Internet using IP phone
•
The fax log report shows an error
The HP All-in-One is having problems sending and receiving faxes
Cause: The HP All-in-One is not set up properly for faxing.
Solution: Follow the instructions to set up the HP All-in-One properly for faxing, based on the equipment and services you have on the same phone line as the HP Allin-One. Then, run a fax test to check the status of the HP All-in-One and to make sure you set it up properly. For more information, see
Set up the HP All-in-One for faxing
.
Fax troubleshooting 181
Chapter 11
The HP All-in-One prints a report with the results of the test. If the test fails, review the report for information on how to fix the problem.
To test your fax setup from the control panel
1.
Set up the HP All-in-One for faxing according to your particular home or office setup instructions.
2.
Insert the print cartridges and load full-size paper in the input tray before starting the test.
3.
Press Setup.
4.
Press 6, then press 6 again.
This selects the Tools menu and then selects Run Fax Test.
The HP All-in-One displays the status of the test on the display and prints a report.
5.
Review the report.
• If the test passes and you are still having problems faxing, check the fax settings listed in the report to verify the settings are correct. A blank or incorrect fax setting can cause problems faxing.
• If the test fails, review the report for more information on how to fix any problems found.
6.
After you pick up the fax report from the HP All-in-One, press OK.
If necessary, resolve any problems found and rerun the test.
Cause: The HP All-in-One is turned off.
Solution: Look at the display on the HP All-in-One. If the display is blank and the
Power button is not lit, the HP All-in-One is turned off. Make sure the power cord is firmly connected to the HP All-in-One and plugged into a power outlet. Press the
Power button to turn on the HP All-in-One.
Cause: The wrong phone cord is used to connect the HP All-in-One or the phone cord is plugged into the wrong port.
Solution:
NOTE:
This possible solution applies only in the countries/regions that receive a 2-wire phone cord in the box with the HP All-in-One, including: Argentina,
Australia, Brazil, Canada, Chile, China, Colombia, Greece, India, Indonesia,
Ireland, Japan, Korea, Latin America, Malaysia, Mexico, Philippines, Poland,
Portugal, Russia, Saudi Arabia, Singapore, Spain, Taiwan, Thailand, USA,
Venezuela, and Vietnam.
Make sure you used the phone cord supplied in the box with the HP All-in-One to connect to the telephone wall jack. One end of this special 2-wire phone cord should
182 Troubleshooting
be connected to the port labeled 1-LINE on the back of the HP All-in-One and the other end to your telephone wall jack, as shown below.
1 Telephone wall jack
2 Use the phone cord supplied in the box with the HP All-in-One
This special 2-wire phone cord is different from the more common 4-wire phone cords you might already have in your office. Check the end of the cord and compare it to the two types of cords shown below.
If you used a 4-wire phone cord, disconnect it, find the supplied 2-wire phone cord, and then connect the 2-wire phone cord to the port labeled 1-LINE on the back of the
HP All-in-One.
If the HP All-in-One came with a 2-wire phone cord adaptor, you can use it with a 4wire phone cord, in case the supplied 2-wire phone cord is too short. Attach the 2wire phone cord adaptor to the port labeled 1-LINE on the back of the HP All-in-One.
Attach your 4-wire phone cord to the open port on the adaptor and to the telephone wall jack. For more information on using the 2-wire phone cord adaptor, see the documentation that came with it.
Cause: Other office equipment (such as an answering machine or a telephone) is not set up properly with the HP All-in-One.
Fax troubleshooting 183
Chapter 11
Solution:
NOTE:
This possible solution applies only in the countries/regions that receive a 2-wire phone cord in the box with the HP All-in-One, including: Argentina,
Australia, Brazil, Canada, Chile, China, Colombia, Greece, India, Indonesia,
Ireland, Japan, Korea, Latin America, Malaysia, Mexico, Philippines, Poland,
Portugal, Russia, Saudi Arabia, Singapore, Spain, Taiwan, Thailand, USA,
Venezuela, and Vietnam.
Make sure you have correctly connected the HP All-in-One to the telephone wall jack, and correctly connected any additional equipment and services that share the phone line with the HP All-in-One.
Use the port labeled 1-LINE on the back of the HP All-in-One to connect to the telephone wall jack. Use the 2-EXT port to connect to any other equipment, such as an answering machine or a telephone, as shown below.
1 Telephone wall jack
2 Use the phone cord supplied in the box with the HP All-in-One
3 Telephone (optional)
Cause: You are using a phone line splitter.
Solution: A phone line splitter can cause faxing problems. (A splitter is a two-cord connector that plugs into a telephone wall jack.) Try removing the splitter and connecting the HP All-in-One directly to the telephone wall jack.
Cause: The telephone wall jack is not working properly.
Solution: Try connecting a working telephone and phone cord to the telephone wall jack you are using for the HP All-in-One and check for a dial tone. If you do not hear a dial tone, call your local telephone company for service.
Cause: The phone line connection is noisy. Phone lines with poor sound quality
(noise) can cause faxing problems.
Solution: If the failure was due to noise on the phone line, contact the sender to have them resend the fax. The quality might be better when you try again. You can
184 Troubleshooting
check the sound quality of the phone line by plugging a phone into the telephone wall jack and listening for static or other noise. If the problem persists, turn Error
Correction Mode (ECM) off and contact your telephone company.
If you are still having problems faxing, set the Fax Speed to a slower rate such as
Medium or Slow.
To change the ECM setting from the control panel
1.
Press Setup.
2.
Press 5, and then press 6.
This selects Advanced Fax Setup and then selects Error Correction Mode.
3.
Press to select On or Off.
4.
Press OK.
To set the fax speed from the control panel
1.
Press Setup.
2.
Press 5, and then press 7.
This selects Advanced Fax Setup and then selects Fax Speed.
3.
Press to select one of the following settings, and then press OK.
Fax speed setting
Fast
Medium
Slow
Fax speed
v.34 (33600 baud) v.17 (14400 baud) v.29 (9600 baud)
Cause: Other equipment that uses the same phone line as the HP All-in-One might be in use.
Solution: Make sure extension phones (phones on the same phone line, but not connected to the HP All-in-One) or other equipment are not in use or off the hook.
For example, you cannot use the HP All-in-One for faxing if an extension phone is off the hook, or if you are using a computer dial-up modem to send e-mail or access the
Internet.
Cause: The HP All-in-One shares the same phone line with a DSL service and a
DSL filter is not connected.
Solution: If you use a DSL service, make sure that you have a DSL filter connected or you will not be able to fax successfully. The DSL service sends out a digital signal on the phone line that can interfere with the HP All-in-One, preventing the HP All-in-
One from sending and receiving faxes. The DSL filter removes the digital signal and allows the HP All-in-One to communicate properly with the phone line. To check if you already have a filter installed, listen to your phone line or dial tone. If you hear noise or static on the line, you probably do not have a DSL filter installed, or it is installed incorrectly. Obtain a DSL filter from your DSL provider. If you already have a DSL filter, make sure it is connected correctly.
Cause: Another process has caused an error in the HP All-in-One.
Fax troubleshooting 185
Chapter 11
Solution: Check the display or your computer for an error message providing information about the problem and how to solve it. If there is an error, the HP All-in-
One will not send or receive a fax until the error condition is resolved.
For more information on error messages, see Errors .
Cause: You are using either a PBX or an ISDN converter/terminal adapter.
Solution:
• Make sure the HP All-in-One is connected to the port that is designated for fax and phone use. Also, make sure that the terminal adapter is set to the correct switch type for your country/region, if possible.
NOTE:
Some ISDN systems allow you to configure the ports for specific phone equipment. For example, you might have assigned one port for telephone and Group 3 fax and another port for multiple purposes. If you have problems when connected to the fax/phone port of your ISDN converter, try using the port designated for multiple purposes; it might be labeled "multicombi" or something similar.
• Try setting the Fax Speed to Medium or Slow.
Cause: The Fax Speed setting is set too fast.
Solution: You might need to send and receive faxes at a slower rate. Try setting the Fax Speed to Medium or Slow if you use one of the following:
• An Internet phone service
• A PBX system
• Fax over Internet Protocol (FoIP)
• An ISDN service
To set the fax speed from the control panel
1.
Press Setup.
2.
Press 5, and then press 7.
This selects Advanced Fax Setup and then selects Fax Speed.
3.
Press to select one of the following settings, and then press OK.
Fax speed setting
Fast
Medium
Slow
Fax speed
v.34 (33600 baud) v.17 (14400 baud) v.29 (9600 baud)
Cause: The HP All-in-One might be connected to a telephone wall jack that is set up for digital phones.
Solution: Make sure you connect the HP All-in-One to an analog phone line or you will not be able to send or receive faxes. To check if your phone line is digital, connect a regular analog phone to the line and listen for a dial tone. If you do not hear a normal
186 Troubleshooting
sounding dial tone, it might be a phone line set up for digital phones. Connect the
HP All-in-One to an analog phone line and try sending or receiving a fax.
Cause: The HP All-in-One shares the same phone line with a DSL service and the
DSL modem might not be properly grounded.
Solution: If the DSL modem is not properly grounded, it can create noise on the phone line. Phone lines with poor sound quality (noise) can cause faxing problems.
You can check the sound quality of the phone line by plugging a phone into the telephone wall jack and listening for static or other noise.
If you hear noise
1.
Turn off your DSL modem and completely remove power for at least 15 minutes.
2.
Turn the DSL modem back on.
3.
Listen to the dial tone again. If the dial tone sounds clear (no noise or static), try sending or receiving a fax.
NOTE:
You might notice static on the phone line again in the future. If the HP Allin-One stops sending and receiving faxes, repeat this process.
If the phone line is still noisy, contact your phone company. For information on turning your DSL modem off, contact your DSL provider for support.
Cause: You are faxing over the Internet using an IP phone, and there was a problem with the transmission.
Solution: Try resending your fax at a later time. Also, make sure your Internet service provider supports faxing over the Internet.
If the problem persists, contact your Internet service provider.
The HP All-in-One cannot send faxes, but can receive faxes
Cause: The HP All-in-One is not set up properly for faxing.
Solution: Follow the instructions to set up the HP All-in-One properly for faxing, based on the equipment and services you have on the same phone line as the HP Allin-One. Then, run a fax test to check the status of the HP All-in-One and to make sure you set it up properly. For more information, see
Set up the HP All-in-One for faxing
.
The HP All-in-One prints a report with the results of the test. If the test fails, review the report for information on how to fix the problem.
To test your fax setup from the control panel
1.
Set up the HP All-in-One for faxing according to your particular home or office setup instructions.
2.
Insert the print cartridges and load full-size paper in the input tray before starting the test.
3.
Press Setup.
Fax troubleshooting 187
Chapter 11
4.
Press 6, then press 6 again.
This selects the Tools menu and then selects Run Fax Test.
The HP All-in-One displays the status of the test on the display and prints a report.
5.
Review the report.
• If the test passes and you are still having problems faxing, check the fax settings listed in the report to verify the settings are correct. A blank or incorrect fax setting can cause problems faxing.
• If the test fails, review the report for more information on how to fix any problems found.
6.
After you pick up the fax report from the HP All-in-One, press OK.
If necessary, resolve any problems found and rerun the test.
Cause: The HP All-in-One might be dialing too fast or too soon.
Solution: You might need to insert some pauses in the number sequence. For example, if you need to access an outside line before dialing the phone number, insert a pause following the access number. If your number is 95555555, and 9 accesses an outside line, you might insert pauses as follows: 9-555-5555. To enter a pause in the fax number you are typing, press Redial/Pause, or press the Space button repeatedly, until a dash (-) appears on the display.
If you are using a speed dial entry to send the fax, update the speed dial entry to include pauses in the number sequence.
You can also send the fax using monitor dialing. This enables you to listen to the phone line as you dial. You can set the pace of your dialing and respond to prompts as you dial.
Cause: The number you entered when sending the fax is not in the proper format.
Solution: Check to see that the fax number you entered is correct and in the proper format. For example, you might need to dial a "9" prefix, depending on your phone system.
If your phone line has a PBX system, make sure you are dialing the number for an outside line before dialing the fax number.
Cause: The receiving fax machine is having problems.
Solution: To check this, try calling the fax number from a telephone and listen for fax tones. If you cannot hear fax tones, the receiving fax might not be turned on or connected, or a voice mail service could be interfering with the recipient's phone line.
You can also ask the recipient to check the receiving fax machine for any problems.
The HP All-in-One is having problems sending a manual fax
Cause: The recipient's fax machine might not support receiving faxes manually.
Solution: Check with the recipient to see if their fax machine can receive faxes manually.
188 Troubleshooting
Cause: You did not press Start Fax Black or Start Fax Color within three seconds of hearing fax tones.
Solution: If you are sending a fax manually, make sure that you press Start Fax
Black or Start Fax Color within three seconds of hearing the recipient's fax tones, otherwise the transmission might fail.
To send a fax manually from a phone
1.
Load your originals print side up into the document feeder tray.
NOTE:
This feature is not supported if you load your originals on the glass.
You must load your originals in the document feeder tray.
2.
Dial the number by using the keypad on the phone that is connected to the HP Allin-One.
NOTE:
Do not use the keypad on the control panel of the HP All-in-One when manually sending a fax. You must use the keypad on your phone to dial the recipient's number.
3.
If the recipient answers the telephone, you can engage in a conversation before sending your fax.
NOTE:
If a fax machine answers the call, you will hear fax tones from the receiving fax machine. Proceed to the next step to transmit the fax.
4.
Once you are ready to send the fax, press Start Fax Black or Start Fax Color.
NOTE:
If prompted, press 1 to select Send Fax, and then press Start Fax
Black or Start Fax Color again.
If you were speaking with the recipient before sending the fax, inform the recipient that they should press Start on their fax machine after they hear fax tones.
The telephone line is silent while the fax is transmitting. At this point, you can hang up the telephone. If you want to continue speaking with the recipient, remain on the line until the fax transmission is complete.
Cause: The telephone used to initiate the fax call was not connected directly to the
HP All-in-One or was not connected properly.
Solution:
NOTE:
This possible solution applies only in the countries/regions that receive a 2-wire phone cord in the box with the HP All-in-One, including: Argentina,
Australia, Brazil, Canada, Chile, China, Colombia, Greece, India, Indonesia,
Ireland, Japan, Korea, Latin America, Malaysia, Mexico, Philippines, Poland,
Portugal, Russia, Saudi Arabia, Singapore, Spain, Taiwan, Thailand, USA,
Venezuela, and Vietnam.
Fax troubleshooting 189
Chapter 11
To send a fax manually, the telephone must be connected directly to the port labeled
2-EXT on the HP All-in-One, as shown below.
1 Telephone wall jack
2 Use the phone cord supplied in the box with the HP All-in-One
3 Telephone
Cause: The Fax Speed setting might be set too fast.
Solution: Try setting the Fax Speed to Medium or Slow, and then resend the fax.
To set the fax speed from the control panel
1.
Press Setup.
2.
Press 5, and then press 7.
This selects Advanced Fax Setup and then selects Fax Speed.
3.
Press to select one of the following settings, and then press OK.
Fax speed setting
Fast
Medium
Slow
Fax speed
v.34 (33600 baud) v.17 (14400 baud) v.29 (9600 baud)
Cause: The HP All-in-One is not detecting an original loaded in the document feeder tray.
Solution: If you did not load an original in the document feeder tray, or if the original is not pushed in far enough, you will be unable to send a fax manually. Load an original in the document feeder tray, or push the original farther into the tray. Once the HP Allin-One detects the original, a confirmation message appears on the display.
190 Troubleshooting
Pages of a fax I sent are missing
Cause: Two or more pages were fed through the document feeder tray at the same time.
Solution: Print a Last Transaction report to verify the number of pages that were sent. If two or more pages stuck together and were fed into the document feeder tray at the same time, the number of pages in the report would not match the actual number of pages. If the number of pages listed in the report does not match the actual number of pages, you might need to clean the separator pad in the automatic document feeder.
To print a Last Transaction report
1.
Press Setup, and then press 2.
This selects Print Report.
2.
Press to select Last Transaction, and then press OK.
For more information on cleaning the separator pad, see
Clean the automatic document feeder .
Cause: The receiving fax machine is having problems.
Solution: To check this, try calling the fax number from a telephone and listen for fax tones. If you cannot hear fax tones, the receiving fax might not be turned on or connected, or a voice mail service could be interfering with the recipient's phone line.
The memory of the receiving fax machine might be full or the fax machine might have run out of paper. You can ask the recipient to check the receiving fax machine for any problems.
Cause: The phone line connection is noisy. Phone lines with poor sound quality
(noise) can cause faxing problems.
Solution: If the failure was due to noise on the phone line, contact the sender to have them resend the fax. The quality might be better when you try again. You can check the sound quality of the phone line by plugging a phone into the telephone wall jack and listening for static or other noise. If the problem persists, turn Error
Correction Mode (ECM) off and contact your telephone company.
To change the ECM setting from the control panel
1.
Press Setup.
2.
Press 5, and then press 6.
This selects Advanced Fax Setup and then selects Error Correction Mode.
3.
Press to select On or Off.
4.
Press OK.
The quality of the fax I sent is poor
Cause: The phone line connection is noisy. Phone lines with poor sound quality
(noise) can cause faxing problems.
Solution: If the failure was due to noise on the phone line, contact the sender to have them resend the fax. The quality might be better when you try again. You can
Fax troubleshooting 191
Chapter 11 check the sound quality of the phone line by plugging a phone into the telephone wall jack and listening for static or other noise. If the problem persists, turn Error
Correction Mode (ECM) off and contact your telephone company.
If the problem persists, check to see if Error Correction Mode (ECM) is On. If it is not, change the ECM setting to On. Faxes might take longer to send, but the print quality of the received fax should improve.
If the print quality is still poor, turn off ECM, and then contact your telephone provider.
To change the ECM setting from the control panel
1.
Press Setup.
2.
Press 5, and then press 6.
This selects Advanced Fax Setup and then selects Error Correction Mode.
3.
Press to select On or Off.
4.
Press OK.
Cause: The fax resolution setting is set to a low resolution, such as Standard.
Solution: For the highest-quality fax, change the fax resolution to Fine, Very
Fine (if available), or Photo (for black-and-white photographs).
To change the resolution from the control panel
1.
Load your originals print side up into the document feeder tray. If you are sending a single-page fax, such as a photograph, you can also load your original print side down on the glass.
NOTE:
If you are sending a multiple-page fax, you must load the originals in the document feeder tray. You cannot fax a multiple-page document from the glass.
2.
In the Fax area, press Menu.
The Enter Number prompt appears.
3.
Enter the fax number by using the keypad, press Speed Dial or a one-touch speed dial button to select a speed dial, or press Redial/Pause to redial the last number dialed.
4.
In the Fax area, press Menu repeatedly until Resolution appears.
5.
Press to select a resolution setting, and then press OK.
6.
Press Start Fax Black.
•
If the device detects an original loaded in the automatic document
feeder, the HP All-in-One sends the document to the number you entered.
•
If the device does not detect an original loaded in the automatic
document feeder, the Fax from glass? prompt appears. Make sure your original is loaded on the glass, and then press 1 to select Yes.
Cause: The glass of the HP All-in-One might be dirty.
192 Troubleshooting
Solution: If you are sending a fax from the glass, make a copy to check the quality of the printout. If the quality of the printout is poor, clean the glass.
To make a copy from the control panel
1.
Make sure you have paper loaded in the input tray.
2.
Load your original print side down on the right front corner of the glass or print side up in the document feeder tray.
If you use the document feeder tray, place the pages so that the top edge of the document goes in first.
3.
Do one of the following:
• Press Start Copy Black to initiate a black-and-white copy job.
• Press Start Copy Color to initiate a color copy job.
NOTE:
If you have a color original, pressing Start Copy Black produces a black-and-white copy of the color original, while pressing Start Copy Color produces a full-color copy of the color original.
To clean the glass
1.
Turn off the HP All-in-One, and raise the lid.
2.
Clean the glass with a soft cloth or sponge slightly moistened with a nonabrasive glass cleaner.
CAUTION:
Do not use abrasives, acetone, benzene, or carbon tetrachloride on the glass, since they can damage it. Do not place or spray liquid directly on the glass. The liquid might seep under the glass and damage the device.
3.
Dry the glass with a dry, soft, lint-free cloth to prevent spotting.
4.
Turn on the HP All-in-One.
Cause: The receiving fax machine is having problems.
Solution: To check this, try calling the fax number from a telephone and listen for fax tones. If you cannot hear fax tones, the receiving fax might not be turned on or connected, or a voice mail service could be interfering with the recipient's phone line.
You can also ask the recipient to check the receiving fax machine for any problems.
Cause: The Lighter / Darker setting might be set too light. If you are sending a faded, washed out, or handwritten fax, or a document with a watermark (such as a red seal or stamp), you can change the Lighter / Darker setting to send the fax darker than the original.
Fax troubleshooting 193
Chapter 11
Solution: Make a copy to check the quality of the printout. If the printout is too light, you can darken it by adjusting the Lighter / Darker setting when sending the fax.
To change the Lighter / Darker setting from the control panel
1.
Load your originals print side up into the document feeder tray. If you are sending a single-page fax, such as a photograph, you can also load your original print side down on the glass.
NOTE:
If you are sending a multiple-page fax, you must load the originals in the document feeder tray. You cannot fax a multiple-page document from the glass.
2.
In the Fax area, press Menu.
The Enter Number prompt appears.
3.
Enter the fax number by using the keypad, press Speed Dial or a one-touch speed dial button to select a speed dial, or press Redial/Pause to redial the last number dialed.
4.
In the Fax area, press Menu repeatedly until Lighter / Darker appears.
5.
Press to lighten the fax or press to darken it, and then press OK.
The indicator moves to the left or right as you press an arrow button.
6.
Press Start Fax Black.
•
If the device detects an original loaded in the automatic document
feeder, the HP All-in-One sends the document to the number you entered.
•
If the device does not detect an original loaded in the automatic
document feeder, the Fax from glass? prompt appears. Make sure your original is loaded on the glass, and then press 1 to select Yes.
Parts of a fax I sent are cut off
Cause: The fax is larger than letter or A4 paper.
Solution: Some fax machines cannot accept faxes larger than letter or A4 paper.
Make sure the receiving fax machine can accept the paper size you are using. If not, ask the recipient if the receiving fax machine has a fit to page setting they can use to reduce the incoming fax to fit standard paper size such as letter or A4.
The fax I sent was blank when it was received
Cause: The original was not loaded or was loaded incorrectly.
194 Troubleshooting
Solution: Load your originals into the document feeder tray. If you are sending a single-page fax, such as a photograph, you can also load your original on the glass.
To load an original in the document feeder tray
1.
Load your original, with the print side up, into the document feeder tray. Slide the paper into the automatic document feeder until you hear a beep or see a message on the display indicating that the HP All-in-One detected the pages you loaded.
TIP:
For more help on loading originals in the automatic document feeder, refer to the diagram engraved in the document feeder tray.
2.
Slide the paper guides inward until they stop at the left and right edges of the paper.
NOTE:
Remove all originals from the document feeder tray before lifting the lid on the HP All-in-One.
To load an original on the scanner glass
1.
Remove all originals from the document feeder tray, and then lift the lid on the
HP All-in-One.
2.
Load your original print side down on the right front corner of the glass.
Fax troubleshooting 195
Chapter 11
3.
Close the lid.
Fax transmission is slow
Cause: You are sending a fax in color.
Solution: Sending a fax in color can take longer than sending a black-and-white fax. Try sending the fax in black and white.
Cause: The document contains a lot of graphics or has very fine detail.
Solution: For faster transmission, use Standard resolution. This setting provides the fastest possible transmission with the lowest quality of fax. The default resolution is Fine, which can take longer to send.
To change the resolution from the control panel
1.
Load your originals print side up into the document feeder tray. If you are sending a single-page fax, such as a photograph, you can also load your original print side down on the glass.
NOTE:
If you are sending a multiple-page fax, you must load the originals in the document feeder tray. You cannot fax a multiple-page document from the glass.
2.
In the Fax area, press Menu.
The Enter Number prompt appears.
3.
Enter the fax number by using the keypad, press Speed Dial or a one-touch speed dial button to select a speed dial, or press Redial/Pause to redial the last number dialed.
4.
In the Fax area, press Menu repeatedly until Resolution appears.
5.
Press to select a resolution setting, and then press OK.
6.
Press Start Fax Black.
•
If the device detects an original loaded in the automatic document
feeder, the HP All-in-One sends the document to the number you entered.
•
If the device does not detect an original loaded in the automatic
document feeder, the Fax from glass? prompt appears. Make sure your original is loaded on the glass, and then press 1 to select Yes.
Cause: The phone line connection is noisy. Phone lines with poor sound quality
(noise) can cause faxing problems.
Solution: If the failure was due to noise on the phone line, contact the sender to have them resend the fax. The quality might be better when you try again. You can check the sound quality of the phone line by plugging a phone into the telephone wall
196 Troubleshooting
jack and listening for static or other noise. If the problem persists, turn Error
Correction Mode (ECM) off and contact your telephone company.
To change the ECM setting from the control panel
1.
Press Setup.
2.
Press 5, and then press 6.
This selects Advanced Fax Setup and then selects Error Correction Mode.
3.
Press to select On or Off.
4.
Press OK.
Cause: The fax resolution setting is set to a high resolution, such as Fine (the default) or Photo.
Solution: For faster transmission, use Standard resolution. This setting provides the fastest possible transmission with the lowest quality of fax.
To change the resolution from the control panel
1.
Load your originals print side up into the document feeder tray. If you are sending a single-page fax, such as a photograph, you can also load your original print side down on the glass.
NOTE:
If you are sending a multiple-page fax, you must load the originals in the document feeder tray. You cannot fax a multiple-page document from the glass.
2.
In the Fax area, press Menu.
The Enter Number prompt appears.
3.
Enter the fax number by using the keypad, press Speed Dial or a one-touch speed dial button to select a speed dial, or press Redial/Pause to redial the last number dialed.
4.
In the Fax area, press Menu repeatedly until Resolution appears.
5.
Press to select a resolution setting, and then press OK.
6.
Press Start Fax Black.
•
If the device detects an original loaded in the automatic document
feeder, the HP All-in-One sends the document to the number you entered.
•
If the device does not detect an original loaded in the automatic
document feeder, the Fax from glass? prompt appears. Make sure your original is loaded on the glass, and then press 1 to select Yes.
Cause: The receiving fax machine is having problems.
Solution: To check this, try calling the fax number from a telephone and listen for fax tones. If you cannot hear fax tones, the receiving fax might not be turned on or connected, or a voice mail service could be interfering with the recipient's phone line.
You can also ask the recipient to check the receiving fax machine for any problems.
Cause: The Fax Speed option is set to a slow transmission speed.
Fax troubleshooting 197
Chapter 11
Solution: Make sure the Fax Speed option is set to Fast or Medium.
To set the fax speed from the control panel
1.
Press Setup.
2.
Press 5, and then press 7.
This selects Advanced Fax Setup and then selects Fax Speed.
3.
Press to select one of the following settings, and then press OK.
Fax speed setting
Fast
Medium
Slow
Fax speed
v.34 (33600 baud) v.17 (14400 baud) v.29 (9600 baud)
The HP All-in-One cannot receive faxes, but can send faxes
Cause: The HP All-in-One is not set up properly for faxing.
Solution: Follow the instructions to set up the HP All-in-One properly for faxing, based on the equipment and services you have on the same phone line as the HP Allin-One. Then, run a fax test to check the status of the HP All-in-One and to make sure
you set it up properly. For more information, see Set up the HP All-in-One for faxing
.
The HP All-in-One prints a report with the results of the test. If the test fails, review the report for information on how to fix the problem.
To test your fax setup from the control panel
1.
Set up the HP All-in-One for faxing according to your particular home or office setup instructions.
2.
Insert the print cartridges and load full-size paper in the input tray before starting the test.
3.
Press Setup.
4.
Press 6, then press 6 again.
This selects the Tools menu and then selects Run Fax Test.
The HP All-in-One displays the status of the test on the display and prints a report.
5.
Review the report.
• If the test passes and you are still having problems faxing, check the fax settings listed in the report to verify the settings are correct. A blank or incorrect fax setting can cause problems faxing.
• If the test fails, review the report for more information on how to fix any problems found.
6.
After you pick up the fax report from the HP All-in-One, press OK.
If necessary, resolve any problems found and rerun the test.
198 Troubleshooting
Cause: Auto Answer is turned off, which means that the HP All-in-One will not answer incoming calls. You must be available to respond in person to incoming fax calls, or the HP All-in-One will not answer the incoming fax call.
Solution: Depending on your office setup, you might be able to set the HP All-in-
One to answer incoming calls automatically. To find out what the recommended answer mode is for your office setup, see
Choose the recommended answer mode for your setup
.
If you must have Auto Answer off, you will need to press Start Fax Black or Start
Fax Color to receive a fax.
TIP:
If you are not close enough to the HP All-in-One to reach the control panel, wait several seconds, and then press 1 2 3 on your phone. If the HP All-in-One does not begin receiving the fax, wait several more seconds and press 1 2 3 again.
After the HP All-in-One begins to receive the fax, you can hang up the phone.
Cause: You subscribe to a voice mail service at the same phone number you use for fax calls.
Solution: Set the HP All-in-One to answer faxes manually. You cannot receive faxes automatically if you have a voice mail service at the same phone number you use for fax calls. You must receive faxes manually; this means you must be available to respond in person to incoming fax calls.
For more information on how to set up the HP All-in-One when you have a voice mail service, see
Set up the HP All-in-One for faxing .
Cause: You have a computer dial-up modem on the same phone line as the HP Allin-One.
Solution: If you have a computer dial-up modem on the same phone line as the
HP All-in-One, check to make sure that the software that came with your modem is not set to receive faxes automatically. Modems that are set up to receive faxes automatically take over the phone line to receive all incoming faxes, which prevents the HP All-in-One from receiving fax calls.
Cause: If you have an answering machine on the same phone line with the HP Allin-One, you might have one of the following problems:
• Your outgoing message might be too long or too loud to allow the HP All-in-One to detect fax tones, and the sending fax machine might disconnect.
• Your answering machine might not have enough quiet time after your outgoing message to allow the HP All-in-One to detect fax tones. This problem is most common with digital answering machines.
Fax troubleshooting 199
Chapter 11
Solution: If you have an answering machine on the same phone line with the HP Allin-One, do the following:
• Disconnect the answering machine and then try receiving a fax. If faxing is successful without the answering machine, the answering machine might be causing the problem.
• Reconnect the answering machine and record your outgoing message again.
Record a message that is approximately 10 seconds in duration. Speak slowly and at a low volume when recording your message. Leave at least 5 seconds of silence at the end of the voice message. There should be no background noise when recording this silent time. Try to receive a fax again.
Cause: The answering machine is not set up properly with the HP All-in-One.
Solution:
NOTE:
This possible solution applies only in the countries/regions that receive a 2-wire phone cord in the box with the HP All-in-One, including: Argentina,
Australia, Brazil, Canada, Chile, China, Colombia, Greece, India, Indonesia,
Ireland, Japan, Korea, Latin America, Malaysia, Mexico, Philippines, Poland,
Portugal, Russia, Saudi Arabia, Singapore, Spain, Taiwan, Thailand, USA,
Venezuela, and Vietnam.
When you have an answering machine on the same phone line you use for fax calls, you must connect the answering machine directly to the HP All-in-One using the port
200 Troubleshooting
labeled 2-EXT, as shown below. You also need to set the correct number of rings to answer for both the answering machine and HP All-in-One.
1 Telephone wall jack
2 Connect to the IN port on the answering machine
3 Connect to the OUT port on the answering machine
4 Telephone (optional)
5 Answering machine
6 Use the phone cord supplied in the box with the HP All-in-One
Make sure the HP All-in-One is set to receive faxes automatically and that the Rings
to Answer setting is correct. The number of rings to answer for the HP All-in-One should be greater than the number of rings to answer for the answering machine. Set your answering machine to a low number of rings and the HP All-in-One to answer in the maximum number of rings supported by your device. (The maximum number of rings varies by country/region.) In this setup, the answering machine will answer the call and the HP All-in-One will monitor the line. If the HP All-in-One detects fax tones, the HP All-in-One will receive the fax. If the call is a voice call, the answering machine will record the incoming message.
To set the number of rings before answering from the control panel
1.
Press Setup.
2.
Press 4, and then press 3.
This selects Basic Fax Setup and then selects Rings to Answer.
3.
Enter the appropriate number of rings by using the keypad, or press or to change the number of rings.
4.
Press OK to accept the setting.
Fax troubleshooting 201
Chapter 11
To set the answer mode
1.
Press Setup.
2.
Press 4, and then press 2.
This selects Basic Fax Setup and then selects Rings to Answer.
3.
Enter the appropriate number of rings by using the keypad, or press or to change the number of rings.
4.
Press OK to accept the setting.
Cause: You have a special ring pattern for your fax phone number (using a distinctive ring service through your telephone company), and the Distinctive Ring setting on the HP All-in-One does not match.
Solution: If you have a special ring pattern for your fax phone number (using a distinctive ring service through your telephone company), make sure that the
Distinctive Ring setting on the HP All-in-One is set to match. For example, if the phone company has assigned your number a double ring pattern, make sure Double
Rings is selected as the Distinctive Ring setting.
NOTE:
The HP All-in-One cannot recognize some ring patterns, such as those with alternating short and long ringing patterns. If you are having problems with a ring pattern of this type, ask your phone company to assign a non-alternating ring pattern.
If you are not using a distinctive ring service, make sure that the Distinctive Ring setting on the HP All-in-One is set to All Rings.
To change the distinctive ring pattern from the control panel
1.
Verify that the HP All-in-One is set to answer fax calls automatically.
2.
Press Setup.
3.
Press 5, and then press 1.
This selects Advanced Fax Setup and then selects Distinctive Ring.
4.
Press to select an option, and then press OK.
When the phone rings with the ring pattern assigned to your fax line, the HP Allin-One answers the call and receives the fax.
Cause: The Distinctive Ring setting is not set to All Rings (and you are not using a distinctive ring service).
Solution: If you are not using a distinctive ring service, make sure that the
Distinctive Ring setting on the HP All-in-One is set to All Rings.
Cause: The fax signal level might not be strong enough, which can cause fax reception problems.
Solution: If the HP All-in-One shares the same phone line with other types of phone equipment, such as an answering machine, a computer dial-up modem, or a multiport switch box, the fax signal level might be reduced. The signal level can also be
202 Troubleshooting
reduced if you use a splitter or connect extra cables to extend the length of your phone. A reduced fax signal can cause problems during fax reception.
• If you are using a splitter or extension cables, try removing them and connecting the HP All-in-One directly to the telephone wall jack.
• To find out if other equipment is causing a problem, disconnect everything except the HP All-in-One from the phone line, and then try to receive a fax. If you can receive faxes successfully without the other equipment, one or more pieces of the other equipment is causing problems; try adding them back one at a time and receiving a fax each time, until you identify which equipment is causing the problem.
Cause: The memory of the HP All-in-One is full.
Solution: If Backup Fax Reception is enabled and there is an error condition on the HP All-in-One, the memory might become full of faxes that have not yet been printed and the HP All-in-One will stop answering calls. If an error condition exists that is preventing the HP All-in-One from printing faxes, review the display for information on the error condition. Also, check for the following problems:
•
.
• There is no paper loaded in the input tray.
• There is a paper jam.
• The print cartridge door is open. Close the print cartridge door, as shown below:
• The print carriage is stalled. Turn the HP All-in-One off, remove any objects that are blocking the print carriage (including any packing materials), and then turn the HP All-in-One on again.
Fax troubleshooting 203
Chapter 11
Resolve any problems found. The HP All-in-One automatically begins printing all the unprinted faxes from memory. To clear the memory, you can also delete the faxes stored in memory by turning off the HP All-in-One.
Cause: An error condition is preventing the HP All-in-One from receiving faxes and Backup Fax Reception is set to Off.
Solution: Check for the following problems:
• The HP All-in-One is turned off. Press the Power button to turn on the device.
• The HP All-in-One is not set up properly for faxing. For more information, see
Set up the HP All-in-One for faxing
.
• There is no paper loaded in the input tray.
• There is a paper jam.
• The print cartridge door is open. Close the print cartridge door.
• The print carriage is stalled. Turn the HP All-in-One off, remove any objects that are blocking the print carriage (including any packing materials), and then turn the HP All-in-One on again.
NOTE:
If Backup Fax Reception is enabled and you turn off the HP All-in-
One, all faxes stored in memory are deleted, including any unprinted faxes that you might have received while the HP All-in-One was in an error condition.
You will need to contact the senders to ask them to resend any unprinted faxes. For a list of the faxes you have received, print the Fax Log. The Fax
Log is not deleted when the HP All-in-One is turned off.
After you resolve any problems found, the HP All-in-One can begin answering incoming fax calls.
The HP All-in-One is having problems receiving a manual fax
Cause: There are documents loaded in the document feeder tray.
Solution: The HP All-in-One will not receive a fax manually if documents are loaded in the document feeder tray. Instead, the HP All-in-One attempts to send the documents loaded in the document feeder tray. Remove any originals before manually receiving faxes.
You can also contact the sender to verify that there are documents loaded in the sending fax machine.
Cause: The Fax Speed setting might be set too fast.
204 Troubleshooting
Solution: Set the Fax Speed to Medium or Slow, and then contact the sender to have them resend the fax.
To set the fax speed from the control panel
1.
Press Setup.
2.
Press 5, and then press 7.
This selects Advanced Fax Setup and then selects Fax Speed.
3.
Press to select one of the following settings, and then press OK.
Fax speed setting
Fast
Medium
Slow
Fax speed
v.34 (33600 baud) v.17 (14400 baud) v.29 (9600 baud)
Cause: There is an error message or other prompt on the display.
Solution: Check the display for an error message or prompt providing information about the problem and how to solve it. If there is an error message or prompt on the display, the HP All-in-One will not receive the fax manually until the error condition is resolved and the message is cleared.
If the HP All-in-One has an alignment message, you might be able to press OK to clear the message and resume faxing. For more information on alignment messages,
see Need alignment or alignment failed .
For more information about other errors, see
.
Fax tones are recorded on my answering machine
Cause: The answering machine is not set up properly with the HP All-in-One or the Rings to Answer setting is not correct.
Solution:
NOTE:
This possible solution applies only in the countries/regions that receive a 2-wire phone cord in the box with the HP All-in-One, including: Argentina,
Australia, Brazil, Canada, Chile, China, Colombia, Greece, India, Indonesia,
Ireland, Japan, Korea, Latin America, Malaysia, Mexico, Philippines, Poland,
Portugal, Russia, Saudi Arabia, Singapore, Spain, Taiwan, Thailand, USA,
Venezuela, and Vietnam.
Fax troubleshooting 205
Chapter 11
When you have an answering machine on the same phone line you use for fax calls, you must connect the answering machine directly to the HP All-in-One using the port labeled 2-EXT, as shown below.
1 Telephone wall jack
2 Connect to the IN port on the answering machine
3 Connect to the OUT port on the answering machine
4 Telephone (optional)
5 Answering machine
6 Use the phone cord supplied in the box with the HP All-in-One
Make sure the HP All-in-One is set to receive faxes automatically and that the Rings
to Answer setting is correct. The number of rings to answer for the HP All-in-One should be greater than the number of rings to answer for the answering machine. If the answering machine and the HP All-in-One are set to the same number of rings to answer, both devices will answer the call and fax tones will be recorded on the answering machine.
Set your answering machine to a low number of rings and the HP All-in-One to answer in the maximum number of rings supported. (The maximum number of rings varies by country/region.) In this setup, the answering machine will answer the call and the
HP All-in-One will monitor the line. If the HP All-in-One detects fax tones, the HP Allin-One will receive the fax. If the call is a voice call, the answering machine will record the incoming message.
To set the answer mode
1.
Press Setup.
2.
Press 4, and then press 2.
This selects Basic Fax Setup and then selects Rings to Answer.
3.
Enter the appropriate number of rings by using the keypad, or press or to change the number of rings.
4.
Press OK to accept the setting.
206 Troubleshooting
To set the number of rings before answering from the control panel
1.
Press Setup.
2.
Press 4, and then press 3.
This selects Basic Fax Setup and then selects Rings to Answer.
3.
Enter the appropriate number of rings by using the keypad, or press or to change the number of rings.
4.
Press OK to accept the setting.
Cause: The HP All-in-One is set up to receive faxes manually, which means that the HP All-in-One will not answer incoming calls. You must be available to respond in person to incoming fax calls, or the HP All-in-One will not receive the fax and your answering machine will record the fax tones.
Solution: Set up the HP All-in-One to answer incoming calls automatically by turning on Auto Answer. If it is turned off, the HP All-in-One will not monitor incoming calls and receive faxes. In this case, the answering machine will answer the fax call and record the fax tones.
For more information on setting up the HP All-in-One when you have an answering
machine, see Set up the HP All-in-One for faxing .
The HP All-in-One is not answering incoming fax calls
Cause: The HP All-in-One is turned off.
Solution: Look at the display on the HP All-in-One. If the display is blank and the
Power button is not lit, the HP All-in-One is turned off. Make sure the power cord is firmly connected to the HP All-in-One and plugged into a power outlet. Press the
Power button to turn on the HP All-in-One.
Cause: Auto Answer is turned off, which means that the HP All-in-One will not answer incoming calls. You must be available to respond in person to incoming fax calls, or the HP All-in-One will not answer the incoming fax call.
Solution: Depending on your office setup, you might be able to set the HP All-in-
One to answer incoming calls automatically. To find out what the recommended answer mode is for your office setup, see
Choose the recommended answer mode for your setup
.
If you must have Auto Answer off, you will need to press Start Fax Black or Start
Fax Color to receive a fax.
TIP:
If you are not close enough to the HP All-in-One to reach the control panel, wait several seconds, and then press 1 2 3 on your phone. If the HP All-in-One does not begin receiving the fax, wait several more seconds and press 1 2 3 again.
After the HP All-in-One begins to receive the fax, you can hang up the phone.
Cause: You have a special ring pattern for your fax phone number (using a distinctive ring service through your telephone company), and the Distinctive Ring setting on the HP All-in-One does not match.
Fax troubleshooting 207
Chapter 11
Solution: If you have a special ring pattern for your fax phone number (using a distinctive ring service through your telephone company), make sure that the
Distinctive Ring feature on the HP All-in-One is set to match. For example, if the phone company has assigned your number a double ring pattern, make sure Double
Rings is selected as the Distinctive Ring setting.
NOTE:
The HP All-in-One cannot recognize some ring patterns, such as those with alternating short and long ringing patterns. If you are having problems with a ring pattern of this type, ask your phone company to assign a non-alternating ring pattern.
If you are not using a distinctive ring service, check to make sure that the Distinctive
Ring feature on the HP All-in-One is set to All Rings.
To change the distinctive ring pattern from the control panel
1.
Verify that the HP All-in-One is set to answer fax calls automatically.
2.
Press Setup.
3.
Press 5, and then press 1.
This selects Advanced Fax Setup and then selects Distinctive Ring.
4.
Press to select an option, and then press OK.
When the phone rings with the ring pattern assigned to your fax line, the HP Allin-One answers the call and receives the fax.
Cause: The Distinctive Ring feature is not set to All Rings (and you are not using a distinctive ring service).
Solution: If you are not using a distinctive ring service, check to make sure that the Distinctive Ring feature on the HP All-in-One is set to All Rings.
Cause: The memory of the HP All-in-One is full.
Solution: If the memory becomes full of faxes that have not yet been printed, the
HP All-in-One stops answering calls. If an error condition exists that is preventing the
HP All-in-One from printing faxes, review the display for information on the error condition. Also, check for the following problems:
• The HP All-in-One is not set up properly for faxing. For more information, see
Set up the HP All-in-One for faxing
.
• There is no paper loaded in the input tray.
• There is a paper jam.
208 Troubleshooting
• The print cartridge door is open. Close the print cartridge door, as shown below:
• The print carriage is stalled. Turn the HP All-in-One off, remove any objects that are blocking the print carriage (including any packing materials), and then turn the HP All-in-One on again.
NOTE:
If Backup Fax Reception is enabled and you turn off the HP All-in-
One, all faxes stored in memory are deleted, including any unprinted faxes that you might have received while the HP All-in-One was in an error condition.
You will need to contact the senders to ask them to resend any unprinted faxes. For a list of the faxes you have received, print the Fax Log. The Fax
Log is not deleted when the HP All-in-One is turned off.
Resolve any problems found. To clear the memory, you can either print or delete the faxes stored in memory.
To reprint faxes in memory from the control panel
1.
Make sure you have paper loaded in the input tray.
2.
Press Setup.
3.
Press 6, and then press 5.
This selects Tools and then selects Reprint Faxes in Memory.
The faxes are printed in the reverse order they were received with the most recently received fax printed first, and so on.
4.
If you want to stop reprinting the faxes in memory, press Cancel.
Fax troubleshooting 209
Chapter 11
To delete all the faxes in memory from the control panel
▲ Turn off the HP All-in-One by pressing the Power button.
All faxes stored in memory will be deleted from memory when you turn off the power to the HP All-in-One.
NOTE:
You can also delete any faxes stored in memory by selecting Clear
Fax Log from the Tools menu. To do so, press Setup, press 6, and then press 7.
Cause: An error condition is preventing the HP All-in-One from receiving faxes and Backup Fax Reception is set to Off.
Solution: Check for the following problems:
• The HP All-in-One is turned off. Press the Power button to turn on the device.
• The HP All-in-One is not set up properly for faxing. For more information, see
Set up the HP All-in-One for faxing
.
• There is no paper loaded in the input tray.
• There is a paper jam.
• The print cartridge door is open. Close the print cartridge door.
• The print carriage is stalled. Turn the HP All-in-One off, remove any objects that are blocking the print carriage (including any packing materials), and then turn the HP All-in-One on again.
After you resolve any problems found, the HP All-in-One can begin answering incoming fax calls.
Pages of a fax I received are missing
Cause: The paper is not loaded correctly in the input tray.
Solution: Make sure you have paper loaded correctly.
To load full-size paper
1.
Remove the output tray.
210 Troubleshooting
2.
Slide the paper-width guide to its outermost position.
3.
Tap a stack of paper on a flat surface to align the edges, and then check the paper for the following:
• Make sure it is free of rips, dust, wrinkles, and curled or bent edges.
• Make sure all the paper in the stack is the same size and type.
4.
Insert the stack of paper into the input tray with the short edge forward and the print side down. Slide the stack of paper forward until it stops.
CAUTION:
Make sure that the HP All-in-One is idle and silent when you load paper into the input tray. If the HP All-in-One is servicing the print cartridges or otherwise engaged in a task, the paper stop inside the device might not be in place. You could push the paper too far forward, causing the HP All-in-One to eject blank pages.
TIP:
If you are using letterhead, insert the top of the page first with the print side down. For more help on loading full-size paper and letterhead, refer to the diagram engraved in the base of the input tray.
Fax troubleshooting 211
Chapter 11
5.
Slide the paper-width guide inward until it stops at the edge of the paper.
Do not overload the input tray; make sure the stack of paper fits within the input tray and is no higher than the top of the paper-width guide.
6.
Replace the output tray.
7.
Flip the tray extender up toward you.
NOTE:
When you use legal-size paper, leave the tray extender closed.
If you have Backup Fax Reception enabled, the HP All-in-One might have stored the fax in memory upon reception. After you have correctly loaded the paper in the input tray, the HP All-in-One automatically begins printing all the unprinted faxes from memory, in the order they were received. If you do not have Backup Fax
Reception enabled, or if the fax was not stored in memory for some reason (for example, if the HP All-in-One was out of memory), you will need to contact the sender and ask for the fax to be resent.
212 Troubleshooting
Cause: The sending fax machine is having problems.
Solution: Check with the sender to find out how many pages were sent. The sending fax machine might have failed to feed each page of the original.
Faxes are received but do not print
Cause: The HP All-in-One has a paper jam or is out of paper.
Solution: If you have Backup Fax Reception enabled, the HP All-in-One might have stored the fax in memory upon reception. After clearing the paper jam or loading paper in the input tray, the HP All-in-One automatically begins printing all the unprinted faxes from memory, in the order they were received. If you do not have
Backup Fax Reception enabled, or if the fax was not stored in memory for some reason (for example, if the HP All-in-One was out of memory), ask the sender to resend the fax.
For more information on clearing paper jams, see Clear paper jams .
Cause: Another process has caused an error in the HP All-in-One.
Solution: Check the display or your computer for an error message providing information about the problem and how to solve it. If there is an error, the HP All-in-
One will not print the fax until the error condition is resolved.
For more information on error messages, see Errors .
Cause: The print cartridges might be out of ink.
Solution: Check the estimated ink levels remaining in the print cartridges. If the print cartridges are low or out of ink, you might need to replace the print cartridges.
If there is ink remaining in the print cartridges, but you are still noticing a problem, print a self-test report to determine if there is a problem with the print cartridges. If the self-test report shows a problem, clean the print cartridges. If the problem persists, you might need to replace the print cartridges.
For more information on print cartridges, see Print cartridge troubleshooting .
Cause: The print carriage is stalled.
Solution: Turn the HP All-in-One off, remove any objects that are blocking the print carriage (including any packing materials), and then turn the HP All-in-One on again.
NOTE:
If Backup Fax Reception is enabled and you turn off the HP All-in-One, all faxes stored in memory are deleted, including any unprinted faxes that you might have received while the HP All-in-One was in an error condition. You will need to contact the senders to ask them to resend any unprinted faxes. For a list of the faxes you have received, print the Fax Log. The Fax Log is not deleted when the HP All-in-One is turned off.
Fax troubleshooting 213
Chapter 11
Parts of a fax I received are cut off
Cause: The sending fax machine has a problem.
Solution: Check with the sender to see if the sending fax machine is having problems.
Cause: The fax originated on a larger paper size, such as legal, and the Automatic
Reduction option is turned off.
Solution: You can print the fax on legal-size paper or you can set the Automatic
Reduction feature to reduce the image so, if possible, it fits on one page.
To print the fax on legal paper
1.
Load legal paper in the input tray.
2.
Change the paper size for received faxes to legal.
3.
Turn off Automatic Reduction.
Cause: The paper-width guide is not positioned correctly.
Solution: Make sure you have paper loaded correctly.
To load full-size paper
1.
Remove the output tray.
2.
Slide the paper-width guide to its outermost position.
214 Troubleshooting
3.
Tap a stack of paper on a flat surface to align the edges, and then check the paper for the following:
• Make sure it is free of rips, dust, wrinkles, and curled or bent edges.
• Make sure all the paper in the stack is the same size and type.
4.
Insert the stack of paper into the input tray with the short edge forward and the print side down. Slide the stack of paper forward until it stops.
CAUTION:
Make sure that the HP All-in-One is idle and silent when you load paper into the input tray. If the HP All-in-One is servicing the print cartridges or otherwise engaged in a task, the paper stop inside the device might not be in place. You could push the paper too far forward, causing the HP All-in-One to eject blank pages.
TIP:
If you are using letterhead, insert the top of the page first with the print side down. For more help on loading full-size paper and letterhead, refer to the diagram engraved in the base of the input tray.
5.
Slide the paper-width guide inward until it stops at the edge of the paper.
Do not overload the input tray; make sure the stack of paper fits within the input tray and is no higher than the top of the paper-width guide.
Fax troubleshooting 215
Chapter 11
6.
Replace the output tray.
7.
Flip the tray extender up toward you.
NOTE:
When you use legal-size paper, leave the tray extender closed.
Cause: A legal-size fax was sent that contained very fine detail, such as large graphics, and letter-size paper is loaded in the input tray.
Solution: If a legal-size fax was sent that contained very fine detail, such as large graphics, the HP All-in-One will attempt to fit the fax on one page (if automatic reduction is enabled). If the memory is full, the HP All-in-One might not be able to reduce the image, causing it to be cut off and printed on a second page. You can clear the memory and have the sender resend the fax.
NOTE:
Clearing the memory will delete all faxes that are stored in memory, including any faxes that have not been printed. You might want to print all faxes in memory to make sure you do not lose any information.
To reprint faxes in memory from the control panel
1.
Make sure you have paper loaded in the input tray.
2.
Press Setup.
3.
Press 6, and then press 5.
This selects Tools and then selects Reprint Faxes in Memory.
The faxes are printed in the reverse order they were received with the most recently received fax printed first, and so on.
4.
If you want to stop reprinting the faxes in memory, press Cancel.
216 Troubleshooting
To delete all the faxes in memory from the control panel
▲ Turn off the HP All-in-One by pressing the Power button.
All faxes stored in memory will be deleted from memory when you turn off the power to the HP All-in-One.
NOTE:
You can also delete any faxes stored in memory by selecting Clear
Fax Log from the Tools menu. To do so, press Setup, press 6, and then press 7.
Cause: The paper loaded in the input tray is a different size than the Fax Paper
Size setting.
Solution: Make sure the paper loaded in the input tray matches the Fax Paper
Size setting.
The computer to which I am connecting has only one phone port
Cause: I am setting up the HP All-in-One on a shared voice/fax line with a computer dial-up modem, and the computer has only one phone port.
Solution:
NOTE:
This possible solution applies only in the countries/regions that receive a 2-wire phone cord in the box with the HP All-in-One, including: Argentina,
Australia, Brazil, Canada, Chile, China, Colombia, Greece, India, Indonesia,
Ireland, Japan, Korea, Latin America, Malaysia, Mexico, Philippines, Poland,
Portugal, Russia, Saudi Arabia, Singapore, Spain, Taiwan, Thailand, USA,
Venezuela, and Vietnam.
If your computer has only one phone port, you will need to purchase a parallel splitter
(also called a coupler), as shown below. (A parallel splitter has one RJ-11 port on the front and two RJ-11 ports on the back. Do not use a 2-line phone splitter, a serial splitter, or a parallel splitter which has two RJ-11 ports on the front and a plug on the back.)
Figure 11-1 Example of a parallel splitter
Fax troubleshooting 217
Chapter 11
Figure 11-2 Back view of the HP All-in-One
1 Telephone wall jack
2 Phone cord connected to the 2-EXT port
3 Parallel splitter
4 Telephone (optional)
5 Computer with modem
6 Phone cord supplied in the box with the HP All-in-One connected to the 1-LINE port
To set up the HP All-in-One to a computer with one phone port
1.
Find the phone cord that connects from the back of your computer (your computer dial-up modem) to a telephone wall jack. Disconnect the cord from the telephone wall jack and plug it into the port labeled 2-EXT on the back of the HP All-in-One.
2.
Using the phone cord supplied in the box with the HP All-in-One, connect one end to your telephone wall jack, then connect the other end to the port labeled 1-LINE on the back of the HP All-in-One.
NOTE:
If you do not use the supplied cord to connect from the telephone wall jack to the HP All-in-One, you might not be able to fax successfully. This special phone cord is different from the phone cords you might already have in your home or office.
3.
Remove the white plug from the port labeled 2-EXT on the back of the HP All-in-
One.
4.
Using another phone cord, connect one end to the port labeled 2-EXT on the back of the HP All-in-One. Connect the other end of the phone cord to the parallel splitter on the side with the single phone port.
5.
Unplug your computer modem from the telephone wall jack, and connect it to the parallel splitter on the side with two phone ports.
6.
If your modem software is set to receive faxes to your computer automatically, turn off that setting.
NOTE:
If you do not turn off the automatic fax reception setting in your modem software, the HP All-in-One will not be able to receive faxes.
218 Troubleshooting
7.
(Optional) Connect a phone to the other open phone port on the parallel splitter.
8.
Now you need to decide how you want the HP All-in-One to answer calls, automatically or manually:
• If you set up the HP All-in-One to answer calls automatically, it answers all incoming calls and receives faxes. The HP All-in-One will not be able to distinguish between fax and voice calls in this case; if you suspect the call is a voice call, you will need to answer it before the HP All-in-One answers the call. To set up the HP All-in-One to answer calls automatically, turn on the
Auto Answer setting.
• If you set up the HP All-in-One to answer faxes manually, you must be available to respond in person to incoming fax calls or the HP All-in-One cannot receive faxes. To set up the HP All-in-One to answer calls manually, turn off the Auto Answer setting.
9.
Run a fax test.
If you pick up the phone before the HP All-in-One answers the call and hear fax tones from a sending fax machine, you will need to answer the fax call manually.
Cause: I am setting up the HP All-in-One on a shared voice/fax line with a computer dial-up modem and answering machine, and the computer only has one phone port.
Solution:
NOTE:
This possible solution applies only in the countries/regions that receive a 2-wire phone cord in the box with the HP All-in-One, including: Argentina,
Australia, Brazil, Canada, Chile, China, Colombia, Greece, India, Indonesia,
Ireland, Japan, Korea, Latin America, Malaysia, Mexico, Philippines, Poland,
Portugal, Russia, Saudi Arabia, Singapore, Spain, Taiwan, Thailand, USA,
Venezuela, and Vietnam.
If your computer has only one phone port, you will need to purchase a parallel splitter
(also called a coupler). (A parallel splitter has one RJ-11 port on the front and two
Fax troubleshooting 219
Chapter 11
RJ-11 ports on the back. Do not use a 2-line phone splitter, a serial splitter, or a parallel splitter which has two RJ-11 ports on the front and a plug on the back.)
Figure 11-3 Back view of the HP All-in-One
1 Telephone wall jack
2 Phone cord connected to the 2-EXT port
3 Parallel splitter
4 Telephone (optional)
5 Answering machine
6 Computer with modem
7 Phone cord supplied in the box with the HP All-in-One connected to the 1-LINE port
To set up the HP All-in-One to a computer with one phone port
1.
Find the phone cord that connects from the back of your computer (your computer dial-up modem) to a telephone wall jack. Disconnect the cord from the telephone wall jack and plug it into the port labeled 2-EXT on the back of the HP All-in-One.
2.
Using the phone cord supplied in the box with the HP All-in-One, connect one end to your telephone wall jack, then connect the other end to the port labeled 1-LINE on the back of the HP All-in-One.
NOTE:
If you do not use the supplied cord to connect from the telephone wall jack to the HP All-in-One, you might not be able to fax successfully. This special phone cord is different from the phone cords you might already have in your home or office.
3.
Remove the white plug from the port labeled 2-EXT on the back of the HP All-in-
One.
4.
Using another phone cord, connect one end to the port labeled 2-EXT on the back of the HP All-in-One. Connect the other end of the phone cord to the parallel splitter on the side with the single phone port.
5.
Unplug your computer modem from the telephone wall jack, and connect it to the parallel splitter on the side with two phone ports.
220 Troubleshooting
6.
Connect your answering machine to the other open phone port on the parallel splitter.
NOTE:
If you do not connect your answering machine in this way, fax tones from a sending fax machine might be recorded on your answering machine, and you might not be able to receive faxes with the HP All-in-One.
7.
(Optional) If your answering machine does not have a built-in phone, for convenience you might want to connect a phone to the back of your answering machine at the "OUT" port.
8.
If your modem software is set to receive faxes to your computer automatically, turn off that setting.
NOTE:
If you do not turn off the automatic fax reception setting in your modem software, the HP All-in-One will not be able to receive faxes.
9.
Turn on the Auto Answer setting.
10.
Set your answering machine to answer after a low number of rings.
11.
Change the Rings to Answer setting on the HP All-in-One to the maximum number of rings supported by your device. (The maximum number of rings varies by country/region.)
12.
Run a fax test.
When the phone rings, your answering machine will answer after the number of rings you have set, and then play your recorded greeting. The HP All-in-One monitors the call during this time, "listening" for fax tones. If incoming fax tones are detected, the
HP All-in-One will emit fax reception tones and receive the fax; if there are no fax tones, the HP All-in-One stops monitoring the line and your answering machine can record a voice message.
Cause: I am setting up the HP All-in-One on a shared voice/fax line with a computer dial-up modem and voice mail service, and the computer has only one phone port.
Solution:
NOTE:
This possible solution applies only in the countries/regions that receive a 2-wire phone cord in the box with the HP All-in-One, including: Argentina,
Australia, Brazil, Canada, Chile, China, Colombia, Greece, India, Indonesia,
Ireland, Japan, Korea, Latin America, Malaysia, Mexico, Philippines, Poland,
Portugal, Russia, Saudi Arabia, Singapore, Spain, Taiwan, Thailand, USA,
Venezuela, and Vietnam.
If your computer has only one phone port, you will need to purchase a parallel splitter
(also called a coupler). (A parallel splitter has one RJ-11 port on the front and two
Fax troubleshooting 221
Chapter 11
RJ-11 ports on the back. Do not use a 2-line phone splitter, a serial splitter, or a parallel splitter which has two RJ-11 ports on the front and a plug on the back.)
Figure 11-4 Back view of the HP All-in-One
1 Telephone wall jack
2 Phone cord connected to the 2-EXT port
3 Parallel splitter
4 Telephone (optional)
5 Computer with modem
6 Phone cord supplied in the box with the HP All-in-One connected to the 1-LINE port
To set up the HP All-in-One to a computer with one phone port
1.
Find the phone cord that connects from the back of your computer (your computer dial-up modem) to a telephone wall jack. Disconnect the cord from the telephone wall jack and plug it into the port labeled 2-EXT on the back of the HP All-in-One.
2.
Using the phone cord supplied in the box with the HP All-in-One, connect one end to your telephone wall jack, then connect the other end to the port labeled 1-LINE on the back of the HP All-in-One.
NOTE:
If you do not use the supplied cord to connect from the telephone wall jack to the HP All-in-One, you might not be able to fax successfully. This special phone cord is different from the phone cords you might already have in your home or office.
3.
Remove the white plug from the port labeled 2-EXT on the back of the HP All-in-
One.
4.
Using another phone cord, connect one end to the port labeled 2-EXT on the back of the HP All-in-One. Connect the other end of the phone cord to the parallel splitter on the side with the single phone port.
5.
Unplug your computer modem from the telephone wall jack, and connect it to the parallel splitter on the side with two phone ports.
222 Troubleshooting
6.
Connect your answering machine to the other open phone port on the parallel splitter.
NOTE:
If you do not connect your answering machine in this way, fax tones from a sending fax machine might be recorded on your answering machine, and you might not be able to receive faxes with the HP All-in-One.
7.
(Optional) If your answering machine does not have a built-in phone, for convenience you might want to connect a phone to the back of your answering machine at the "OUT" port.
8.
If your modem software is set to receive faxes to your computer automatically, turn off that setting.
NOTE:
If you do not turn off the automatic fax reception setting in your modem software, the HP All-in-One will not be able to receive faxes.
9.
Turn on the Auto Answer setting.
10.
Set your answering machine to answer after a low number of rings.
11.
Change the Rings to Answer setting on the HP All-in-One to the maximum number of rings supported by your device. (The maximum number of rings varies by country/region.)
12.
Run a fax test.
When the phone rings, your answering machine will answer after the number of rings you have set, and then play your recorded greeting. The HP All-in-One monitors the call during this time, "listening" for fax tones. If incoming fax tones are detected, the
HP All-in-One will emit fax reception tones and receive the fax; if there are no fax tones, the HP All-in-One stops monitoring the line and your answering machine can record a voice message.
I hear static on my telephone line since connecting the HP All-in-One
Cause: The HP All-in-One is not set up properly for faxing.
Solution:
NOTE:
This possible solution applies only in the countries/regions that receive a 2-wire phone cord in the box with the HP All-in-One, including: Argentina,
Australia, Brazil, Canada, Chile, China, Colombia, Greece, India, Indonesia,
Ireland, Japan, Korea, Latin America, Malaysia, Mexico, Philippines, Poland,
Portugal, Russia, Saudi Arabia, Singapore, Spain, Taiwan, Thailand, USA,
Venezuela, and Vietnam.
Connect the HP All-in-One to a working telephone wall jack. Make sure you used the phone cord supplied in the box with the HP All-in-One. Connect the 2-wire phone cord
Fax troubleshooting 223
Chapter 11 to the port labeled 1-LINE on the back of the HP All-in-One and to your telephone wall jack, as shown below.
1 Telephone wall jack
2 Use the phone cord supplied in the box with the HP All-in-One
This special 2-wire phone cord is different from the more common 4-wire phone cords you might already have in your office. Check the end of the cord and compare it to the two types of cords shown below.
If you used a 4-wire phone cord, disconnect it, find the supplied 2-wire phone cord, and then connect the 2-wire phone cord to the port labeled 1-LINE on the back of the
HP All-in-One.
If the HP All-in-One came with a 2-wire phone cord adaptor, you can use it with a 4wire phone cord, in case the supplied 2-wire phone cord is too short. Attach the 2wire phone cord adaptor to the port labeled 1-LINE on the back of the HP All-in-One.
Attach your 4-wire phone cord to the open port on the adaptor and to the telephone wall jack. For more information on using the 2-wire phone cord adaptor, see the documentation that came with it.
For more information on setting up the HP All-in-One, see the printed documentation that came with the HP All-in-One.
Cause: You are using a phone line splitter between the 1-LINE port on the HP Allin-One and the wall.
Solution: A phone line splitter can affect the sound quality of your phone line and cause static. (A splitter is a two-cord connector that plugs into a telephone wall jack.)
224 Troubleshooting
Try removing the splitter and connecting the HP All-in-One directly to the telephone wall jack.
Cause: You are not using a proper grounded power outlet for the HP All-in-One.
Solution: Try connecting to another power outlet.
The fax test failed
If you tried to run the fax test from your computer and the fax test failed to run, the
HP All-in-One might be busy with another task or have an error condition preventing it from running the fax test.
What to check
• The HP All-in-One is set up properly, connected to a power supply, and is connected to your computer. For more information on setting up the HP All-in-
One, see the Setup Poster that came with the HP All-in-One.
• The HP All-in-One is turned on. If it is not, press the Power button to turn on the
HP All-in-One.
• The print cartridges are installed correctly, the print carriage is not blocked, and the print cartridge door is closed.
• The HP All-in-One is not currently busy with another task such as aligning the print cartridges. Check the display. If the HP All-in-One is busy, wait until it completes the current task and run the fax test again.
• The rear door is attached to the back of the HP All-in-One.
• There are no error messages on the display. If there is an error message, resolve the problem and run the fax test again.
If you run the fax test and the HP All-in-One reports that the test failed, read the following information carefully to determine how to correct any problems with your fax setup. Different portions of the fax test might fail for different reasons.
Cause: The "Fax Hardware Test" failed.
Solution:
What to do
• Turn off the HP All-in-One by using the Power button located on the control panel and then unplug the power cord from the back of the HP All-in-One. After a few seconds, plug the power cord back in and turn the power on. Run the test again.
If the test fails again, continue reviewing the troubleshooting information in this section.
NOTE:
Depending how long the HP All-in-One is unplugged, the date and time might be erased. You might need to reset the date and time later, when you plug the power cord back in.
• Try to send or receive a test fax. If you can send or receive a fax successfully, there might not be a problem.
After you resolve any problems found, run the fax test again to make sure it passes and the HP All-in-One is ready for faxing. If the Fax Hardware Test continues to fail
Fax troubleshooting 225
Chapter 11 and you experience problems faxing, contact HP Support. Go to www.hp.com/ support . If prompted, choose your country/region, and then click Contact HP for information on calling for technical support.
Cause: The "Fax Connected to Active Telephone Wall Jack" test failed.
Solution:
What to do
• Check the connection between the telephone wall jack and the HP All-in-One to make sure the phone cord is secure.
• Make sure you use the phone cord that came with the HP All-in-One. If you do not use the supplied phone cord to connect from the telephone wall jack to the
HP All-in-One, you might not be able to send or receive faxes. After you plug in the phone cord that came with the HP All-in-One, run the fax test again.
• Make sure you have correctly connected the HP All-in-One to the telephone wall jack. Using the phone cord supplied in the box with the HP All-in-One, connect one end to your telephone wall jack, then connect the other end to the port labeled
1-LINE on the back of the HP All-in-One. For more information, see
1 Telephone wall jack
2 Use the phone cord supplied in the box with the HP All-in-One
• If you are using a phone splitter, this can cause faxing problems. (A splitter is a two-cord connector that plugs into a telephone wall jack.) Try removing the splitter and connecting the HP All-in-One directly to the telephone wall jack.
• Try connecting a working phone and phone cord to the telephone wall jack that you are using for the HP All-in-One and check for a dial tone. If you do not hear a dial tone, contact your telephone company and have them check the line.
• Try to send or receive a test fax. If you can send or receive a fax successfully, there might not be a problem.
After you resolve any problems found, run the fax test again to make sure it passes and the HP All-in-One is ready for faxing.
226 Troubleshooting
Cause: The "Phone Cord Connected to Correct Port on Fax" test failed.
Solution: Plug the phone cord into the correct port.
What to do
1.
Using the phone cord supplied in the box with the HP All-in-One, connect one end to your telephone wall jack, then connect the other end to the port labeled 1-LINE on the back of the HP All-in-One.
NOTE:
If you use the 2-EXT port to connect to the telephone wall jack, you will not be able to send or receive faxes. The 2-EXT port should only be used to connect other equipment, such as an answering machine or a telephone.
1 Telephone wall jack
2 Use the phone cord supplied in the box with the HP All-in-One
2.
After you have connected the phone cord to the port labeled 1-LINE, run the fax test again to make sure it passes and the HP All-in-One is ready for faxing.
3.
Try to send or receive a test fax.
Cause: The "Using Correct Type of Phone Cord with Fax" test failed.
Solution:
• Make sure you used the phone cord supplied in the box with the HP All-in-One to connect to the telephone wall jack. One end of the phone cord should be
Fax troubleshooting 227
Chapter 11 connected to the port labeled 1-LINE on the back of your HP All-in-One and the other end to your telephone wall jack, as shown below.
1 Telephone wall jack
2 Phone cord supplied in the box with the HP All-in-One
• Check the connection between the telephone wall jack and the HP All-in-One to make sure the phone cord is secure.
Cause: The "Fax Line Condition" test failed.
Solution:
What to do
• Make sure you connect the HP All-in-One to an analog phone line or you will not be able to send or receive faxes. To check if your phone line is digital, connect a regular analog phone to the line and listen for a dial tone. If you do not hear a normal sounding dial tone, it might be a phone line set up for digital phones.
Connect the HP All-in-One to an analog phone line and try sending or receiving a fax.
• Check the connection between the telephone wall jack and the HP All-in-One to make sure the phone cord is secure.
• Make sure you have correctly connected the HP All-in-One to the telephone wall jack. Using the phone cord supplied in the box with the HP All-in-One, connect one end to your telephone wall jack, then connect the other end to the port labeled
1-LINE on the back of the HP All-in-One. For more information, see
• Other equipment, which uses the same phone line as the HP All-in-One, might be causing the test to fail. To find out if other equipment is causing a problem,
228 Troubleshooting
disconnect everything except the HP All-in-One from the phone line, and then run the test again.
• If the Fax Line Condition Test passes without the other equipment, then one or more pieces of the equipment is causing problems; try adding them back one at a time and rerunning the test each time, until you identify which piece of equipment is causing the problem.
• If the Fax Line Condition Test fails without the other equipment, connect the
HP All-in-One to a working phone line and continue reviewing the troubleshooting information in this section.
• If you are using a phone splitter, this can cause faxing problems. (A splitter is a two-cord connector that plugs into a telephone wall jack.) Try removing the splitter and connecting the HP All-in-One directly to the telephone wall jack.
After you resolve any problems found, run the fax test again to make sure it passes and the HP All-in-One is ready for faxing. If the Fax Line Condition Test continues to fail and you experience problems faxing, contact your telephone company and have them check the phone line.
Cause: The "Dial Tone Detection" test failed.
Solution:
• Other equipment, which uses the same phone line as the HP All-in-One, might be causing the test to fail. To find out if other equipment is causing a problem, disconnect everything except the HP All-in-One from the phone line, and then run the test again. If the Dial Tone Detection Test passes without the other equipment, then one or more pieces of the equipment is causing problems; try adding them back one at a time and rerunning the test each time, until you identify which piece of equipment is causing the problem.
• Try connecting a working phone and phone cord to the telephone wall jack that you are using for the HP All-in-One and check for a dial tone. If you do not hear a dial tone, contact your telephone company and have them check the line.
• Make sure you have correctly connected the HP All-in-One to the telephone wall jack. Using the phone cord supplied in the box with the HP All-in-One, connect one end to your telephone wall jack, then connect the other end to the port labeled
Fax troubleshooting 229
Chapter 11
1-LINE on the back of the HP All-in-One. For more information, see
1 Telephone wall jack
2 Use the phone cord supplied in the box with the HP All-in-One
• If you are using a phone splitter, this can cause faxing problems. (A splitter is a two-cord connector that plugs into a telephone wall jack.) Try removing the splitter and connecting the HP All-in-One directly to the telephone wall jack.
• If your telephone system is not using a standard dial tone, such as some PBX systems, this might cause the test to fail. This will not cause a problem sending or receiving faxes. Try sending or receiving a test fax.
• Check to make sure the country/region setting is set appropriately for your country/region. If the country/region setting is not set or is set incorrectly, the test might fail and you might have problems sending and receiving faxes.
• Make sure you connect the HP All-in-One to an analog phone line or you will not be able to send or receive faxes. To check if your phone line is digital, connect a regular analog phone to the line and listen for a dial tone. If you do not hear a normal sounding dial tone, it might be a phone line set up for digital phones.
Connect the HP All-in-One to an analog phone line and try sending or receiving a fax.
After you resolve any problems found, run the fax test again to make sure it passes and the HP All-in-One is ready for faxing. If the Dial Tone Detection Test continues to fail, contact your telephone company and have them check the phone line.
I am having problems faxing over the Internet using IP phone
Cause: The fax over Internet Protocol (FoIP) service might not work properly when the HP All-in-One is sending and receiving faxes at high speed (33600 bps).
230 Troubleshooting
Solution: If you experience problems sending and receiving faxes while using an
Internet fax service, use a slower fax speed. You can do this by changing the Fax
Speed setting from Fast (the default) to Medium or Slow.
To set the fax speed from the control panel
1.
Press Setup.
2.
Press 5, and then press 7.
This selects Advanced Fax Setup and then selects Fax Speed.
3.
Press to select one of the following settings, and then press OK.
Fax speed setting
Fast
Medium
Slow
Fax speed
v.34 (33600 baud) v.17 (14400 baud) v.29 (9600 baud)
Cause: The HP All-in-One is not set up properly for faxing.
Solution: You can only send and receive faxes by connecting a phone cord to the port labeled 1-LINE on the HP All-in-One and not from the Ethernet port. This means that your connection to the Internet must be done either through a converter box
(which supplies regular analog phone jacks for fax connections) or your telephone company.
Cause: Your telephone company does not support faxing over the Internet.
Solution: Check with your telephone company to make sure their Internet phone service supports faxing. If they do not support faxing, you will not be able to send and receive faxes through the Internet.
The fax log report shows an error
Cause: If there is a problem or error encountered during sending or receiving a fax, a Fax Log report will print.
Solution: Review the following table for information on the error codes in the Fax
Log report. This information can help you troubleshoot any problems you encounter when using the fax features of the HP All-in-One. The table also indicates which codes are specific to Error Correction Mode (ECM). If the same error appears repeatedly, try turning off ECM.
To change the ECM setting from the control panel
1.
Press Setup.
2.
Press 5, and then press 6.
This selects Advanced Fax Setup and then selects Error Correction Mode.
3.
Press to select On or Off.
4.
Press OK.
Fax troubleshooting 231
Chapter 11
Error code
(223 Error Correction
Mode)
224
225-231
232-234
(235-236 Error Correction
Mode)
237
238
(239-241 Error Correction
Mode)
242
281
(282 Error Correction
Mode)
283-284
(285 Error Correction
Mode)
286
290
291
314-320
321
322-324
(325-328 Error Correction
Mode)
329-331
Error definition
One or more received pages might not be readable.
There is a feature incompatibility with the sending fax machine.
The telephone connection was lost.
The sending fax machine sent an unexpected communication.
243-244
(245-246 Error Correction
Mode)
247-248
(249-251 Error Correction
Mode)
252
253
The sending fax machine is attempting to receive instead of send.
The sending fax machine prematurely ended the session.
There was a communication error with the sending fax machine.
Telephone line conditions were too poor to receive a fax.
The sending fax machine attempted to use an unsupported page width.
The telephone connection was lost.
There was a communication error with the sending fax machine.
The received fax could not be stored.
There is a feature incompatibility with the receiving fax machine.
There was a communication error with the receiving fax machine.
Telephone line conditions were too poor to send a fax.
The receiving fax machine indicated one or more pages might not be readable.
232 Troubleshooting
(continued)
Error code
332-337
(338-342 Error Correction
Mode)
343
344-348
(349-353 Error Correction
Mode)
354-355
356-361
(362-366 Error Correction
Mode)
367-372
(373-377 Error Correction
Mode)
378-380
381
382
383
390-391
Error definition
The receiving fax machine sent an unexpected communication.
The telephone connection was lost.
The receiving fax machine prematurely ended the session.
There was a communication error with the receiving fax machine.
The telephone connection was lost.
The receiving fax machine stopped accepting pages.
The telephone connection was lost.
There was a communication error with the receiving fax machine.
Copy troubleshooting
Use this section to solve these copy problems:
•
Copies are too light or too dark
•
Nothing happens when I try to copy
•
Parts of the original do not appear or are cut off
•
Fit to Page is not working as expected
•
•
A borderless copy has white space around the edges
•
The image is cropped when I make a borderless copy
Copies are too light or too dark
Cause: The Lighter / Darker setting for the HP All-in-One is set too light or too dark.
Copy troubleshooting 233
Chapter 11
Solution: Adjust the lightness and darkness of the copies.
To adjust the copy contrast from the control panel
1.
Make sure you have paper loaded in the input tray.
2.
Load your original print side down on the right front corner of the glass or print side up in the document feeder tray.
If you use the document feeder tray, place the pages so that the top edge of the document goes in first.
3.
In the Copy area, press Menu repeatedly until Lighter / Darker appears.
4.
Do one of the following:
• Press to darken the copy.
• Press to lighten the copy.
5.
Press Start Copy Black or Start Copy Color.
Cause: Try using Enhancements improve an overexposed image.
Solution:
To copy an overexposed photo
1.
Make sure you have paper loaded in the input tray.
2.
Load your original photo print side down on the right front corner of the glass.
Position the photo on the glass so the long edge of the photo is along the front edge of the glass.
3.
In the Copy area, press Menu repeatedly until Enhancements appears.
4.
Press until the Photo enhancement setting appears.
5.
Press Start Copy Color.
Nothing happens when I try to copy
Cause: The HP All-in-One is turned off.
Solution: Look on the HP All-in-One control panel to see if the display is blank, and the Power button is not lit. If these two conditions exist, the HP All-in-One is turned off. Make sure the power cord is connected and plugged into a power outlet. Press the Power button to turn on the HP All-in-One.
Cause: The original is placed incorrectly on the glass or in the document feeder tray.
234 Troubleshooting
Solution: Load the original on the glass or in the document feeder tray.
• If you are loading your original on the glass, place it print side down on the right front corner as shown below. To copy a photo, position the photo so that the long edge of the photo is along the front edge of the glass.
• If you are loading your original in the document feeder tray, place the paper, with the print side up, in the tray as shown below. Place the pages in the tray so that the top of the document goes in first.
NOTE:
Do not load photos in the document feeder tray to copy. If you are copying a photo, place it on the glass.
Cause: The HP All-in-One might be busy copying, printing, or receiving a fax.
Solution: Check the display to see if the HP All-in-One is busy.
Cause: The HP All-in-One does not recognize the paper type.
Solution: Do not use the HP All-in-One to copy onto envelopes or other papers the
HP All-in-One does not support.
Cause: The HP All-in-One has a paper jam.
Copy troubleshooting 235
Chapter 11
Solution: For information on clearing paper jams, see Clear paper jams .
Parts of the original do not appear or are cut off
Cause: The original is placed incorrectly on the glass or in the document feeder tray.
Solution: Load the original on the glass or in the document feeder tray.
• If you are loading your original on the glass, place it print side down on the right front corner as shown below. To copy a photo, position the photo so that the long edge of the photo is along the front edge of the glass.
• If you are loading your original in the document feeder tray, place the paper, print side up, in the tray as shown below. Place the pages in the tray so that the top of the document goes in first.
NOTE:
Do not load photos in the document feeder tray to copy. If you are copying a photo, place it on the glass.
Cause: The original fills the entire sheet.
236 Troubleshooting
Solution: If the image or text on your original fills the entire sheet with no margins, use the Fit to Page feature to reduce your original and prevent unwanted cropping of the text or images at the edges of the sheet.
To resize a document from the control panel
1.
Make sure you have paper loaded in the input tray.
2.
Load your original print side down on the right front corner of the glass or print side up in the document feeder tray.
If you use the document feeder tray, place the pages so that the top edge of the document goes in first.
3.
In the Copy area, press the Reduce/Enlarge button.
4.
Do one of the following:
• If you loaded your original in the document feeder tray or on the glass, press
until Full Page 91% appears.
• If you loaded a full- or small-size original on the glass, press until Fit to
Page appears.
5.
Press Start Copy Black or Start Copy Color.
Cause: The original is larger than the paper in the input tray.
Solution: If your original is larger than the paper in the input tray, use the Fit to
Page feature to reduce your original to fit on the paper in the input tray.
To resize a document from the control panel
1.
Make sure you have paper loaded in the input tray.
2.
Load your original print side down on the right front corner of the glass or print side up in the document feeder tray.
If you use the document feeder tray, place the pages so that the top edge of the document goes in first.
3.
In the Copy area, press the Reduce/Enlarge button.
4.
Do one of the following:
• If you loaded your original in the document feeder tray or on the glass, press
until Full Page 91% appears.
• If you loaded a full- or small-size original on the glass, press until Fit to
Page appears.
5.
Press Start Copy Black or Start Copy Color.
Fit to Page is not working as expected
Cause: You are trying to increase the size of an original that is too small.
Solution: Fit to Page can only enlarge the original up to the maximum percentage allowed by your model. (The maximum percentage varies by model.) For example,
200% might be the maximum enlargement percentage allowed by your model.
Enlarging a passport photo by 200% might not enlarge it enough for it to fit a full-size page.
Copy troubleshooting 237
Chapter 11
If you want to make a large copy of a small original, scan the original into the computer, resize the image in the HP Scan Pro software, and then print a copy of the enlarged image.
Cause: The original is placed incorrectly on the glass.
Solution: Load the original print side down on the right front corner of the glass as shown below. To copy a photo, position the photo on the glass so that the long edge of the photo is along the front edge of the glass.
Cause: The original is placed in the document feeder tray.
Solution: You cannot use the document feeder tray with the Fit to Page feature.
To use the Fit to Page feature, the original must be placed print side down on the right front corner of the glass.
Cause: Debris might be stuck on the glass or on the back of the document lid. The
HP All-in-One interprets anything it detects on the glass as part of the image.
Solution: Turn off the HP All-in-One, unplug the power cord, and then use a soft cloth to wipe the glass and the back of the document lid.
To clean the glass
1.
Turn off the HP All-in-One, and raise the lid.
2.
Clean the glass with a soft cloth or sponge slightly moistened with a nonabrasive glass cleaner.
CAUTION:
Do not use abrasives, acetone, benzene, or carbon tetrachloride on the glass, since they can damage it. Do not place or spray liquid directly on the glass. The liquid might seep under the glass and damage the device.
3.
Dry the glass with a dry, soft, lint-free cloth to prevent spotting.
4.
Turn on the HP All-in-One.
238 Troubleshooting
To clean the lid backing
1.
Turn off the HP All-in-One, unplug the power cord, and raise the lid.
NOTE:
Depending how long the HP All-in-One is unplugged, the date and time might be erased. You might need to reset the date and time later, when you plug the power cord back in.
2.
Clean the white document backing with a soft cloth or sponge slightly moistened with a mild soap and warm water.
Wash the backing gently to loosen debris. Do not scrub the backing.
3.
Dry the backing with a dry, soft, lint-free cloth.
CAUTION:
Do not use paper-based wipes, as these might scratch the backing.
4.
If further cleaning is needed, repeat the previous steps using isopropyl (rubbing) alcohol, and wipe the backing thoroughly with a damp cloth to remove any residual alcohol.
CAUTION:
Be careful not to spill alcohol on the glass or exterior of the HP Allin-One, as this might damage the device.
The printout is blank
Cause: The original is placed incorrectly on the glass or in the document feeder tray.
Solution: Load the original on the glass or in the document feeder tray.
• If you are loading your original on the glass, place it print side down on the right front corner as shown below. To copy a photo, position the photo so that the long edge of the photo is along the front edge of the glass.
Copy troubleshooting 239
Chapter 11
• If you are loading your original in the document feeder tray, place the paper, with print side up, in the tray as shown below. Place the pages in the tray so that the top of the document goes in first.
NOTE:
Do not load photos in the document feeder tray to copy. If you are copying a photo, place it on the glass.
Cause: The print cartridges need to be cleaned or might be out of ink.
Solution: Check the estimated ink levels remaining in the print cartridges. If the print cartridges are low or out of ink, you might need to replace the print cartridges.
If there is ink remaining in the print cartridges, but you are still noticing a problem, print a self-test report to determine if there is a problem with the print cartridges. If the self-test report shows a problem, clean the print cartridges. If the problem persists, you might need to replace the print cartridges.
For more information on print cartridges, see Print cartridge troubleshooting .
A borderless copy has white space around the edges
Cause: You are trying to make a borderless copy of an original that is too small.
Solution: When you make a borderless copy of a small original, the HP All-in-One enlarges the original up to a maximum percentage. This might leave white space around the edges. (The maximum percentage varies by model.)
Depending on the size of the borderless copy you are trying to make, the minimum size of the original varies. For example, you cannot enlarge a passport photo to create a letter-size borderless copy.
If you want to make a borderless copy of a very small original, scan the original into the computer, resize the image in the HP scanning software, and then print a borderless copy of the enlarged image.
Cause: You are trying to make a borderless copy without using photo paper.
240 Troubleshooting
Solution: Use photo paper to make borderless copies.
To make a borderless copy of a photo from the control panel
1.
Load 10 x 15 cm (4 x 6 inch) photo paper in the input tray.
2.
Load your original photo print side down on the right front corner of the glass.
Position the photo on the glass so the long edge of the photo is along the front edge of the glass, as indicated by the engraved guides along the edge of the glass.
3.
Press Start Copy Black or Start Copy Color.
The HP All-in-One makes a 10 x 15 cm (4 x 6 inch) borderless copy of your original photo.
NOTE:
If you loaded tabbed paper in the photo tray, you can remove the tab from the copy of your photo once the ink has completely dried.
TIP:
If the output is not borderless set the paper type to Premium Photo, and then try making the copy again.
Cause: Debris might be stuck on the glass or on the back of the document lid. The
HP All-in-One interprets anything it detects on the glass as part of the image.
Solution: Turn off the HP All-in-One, unplug the power cord, and then use a soft cloth to wipe the glass and the back of the document lid.
To clean the glass
1.
Turn off the HP All-in-One, and raise the lid.
2.
Clean the glass with a soft cloth or sponge slightly moistened with a nonabrasive glass cleaner.
CAUTION:
Do not use abrasives, acetone, benzene, or carbon tetrachloride on the glass, since they can damage it. Do not place or spray liquid directly on the glass. The liquid might seep under the glass and damage the device.
Copy troubleshooting 241
Chapter 11
3.
Dry the glass with a dry, soft, lint-free cloth to prevent spotting.
4.
Turn on the HP All-in-One.
To clean the lid backing
1.
Turn off the HP All-in-One, unplug the power cord, and raise the lid.
NOTE:
Depending how long the HP All-in-One is unplugged, the date and time might be erased. You might need to reset the date and time later, when you plug the power cord back in.
2.
Clean the white document backing with a soft cloth or sponge slightly moistened with a mild soap and warm water.
Wash the backing gently to loosen debris. Do not scrub the backing.
3.
Dry the backing with a dry, soft, lint-free cloth.
CAUTION:
Do not use paper-based wipes, as these might scratch the backing.
4.
If further cleaning is needed, repeat the previous steps using isopropyl (rubbing) alcohol, and wipe the backing thoroughly with a damp cloth to remove any residual alcohol.
CAUTION:
Be careful not to spill alcohol on the glass or exterior of the HP Allin-One, as this might damage the device.
The image is cropped when I make a borderless copy
Cause: The HP All-in-One cropped some of the image around the margins of the copy to achieve a borderless print without changing the proportions of the original.
Solution: If you want to enlarge a photo to fit a full-size page without cropping the edges, use Fit to Page or Full Page 91% .
To set a custom size from the control panel
1.
Make sure you have paper loaded in the input tray.
2.
Load your original print side down on the right front corner of the glass.
If you use the document feeder tray, place the pages so that the top edge of the document goes in first.
3.
In the Copy area, press the Reduce/Enlarge button.
4.
Press until Custom 100% appears.
5.
Press OK.
6.
Press or use the keypad to enter a percentage to reduce or enlarge the copy.
(The minimum and maximum percentage to resize a copy varies by model.)
7.
Press Start Copy Black or Start Copy Color.
242 Troubleshooting
To resize a document from the control panel
1.
Make sure you have paper loaded in the input tray.
2.
Load your original print side down on the right front corner of the glass or print side up in the document feeder tray.
If you use the document feeder tray, place the pages so that the top edge of the document goes in first.
3.
In the Copy area, press the Reduce/Enlarge button.
4.
Do one of the following:
• If you loaded your original in the document feeder tray or on the glass, press
until Full Page 91% appears.
• If you loaded a full- or small-size original on the glass, press until Fit to
Page appears.
5.
Press Start Copy Black or Start Copy Color.
Cause: The original is larger than the paper in the input tray.
Solution: If your original is larger than the paper in the input tray, use the Fit to
Page feature to reduce your original to fit on the paper in the input tray.
To resize a document from the control panel
1.
Make sure you have paper loaded in the input tray.
2.
Load your original print side down on the right front corner of the glass or print side up in the document feeder tray.
If you use the document feeder tray, place the pages so that the top edge of the document goes in first.
3.
In the Copy area, press the Reduce/Enlarge button.
4.
Do one of the following:
• If you loaded your original in the document feeder tray or on the glass, press
until Full Page 91% appears.
• If you loaded a full- or small-size original on the glass, press until Fit to
Page appears.
5.
Press Start Copy Black or Start Copy Color.
Scan troubleshooting
Use this section to solve these scan problems:
•
•
•
Scan fails because of insufficient computer memory
•
•
•
•
Scanned image is incorrectly cropped
•
Scanned image has incorrect page layout
Scan troubleshooting 243
Chapter 11
•
Scanned image shows dotted lines instead of text
•
•
•
The scan feature does not work
Scan halts
Cause: The computer system resources might be low.
Solution: Turn off the HP All-in-One and then turn it back on. Turn off the computer and then turn it back on.
If this does not work, try changing the scan to a lower resolution.
Scan fails
Cause: The computer is not turned on.
Solution: Turn on your computer.
Cause: Your computer is not connected to the HP All-in-One by a USB cable.
Solution: Connect your computer to the HP All-in-One with a standard USB cable.
Cause: The HP All-in-One software might not have been installed.
Solution: Insert the HP All-in-One installation CD and install the software.
Cause: The software you installed with the HP All-in-One is not running.
Solution: Open the software you installed with the HP All-in-One and try scanning again.
Scan fails because of insufficient computer memory
Cause: Too many programs are running on your computer.
Solution: Close all programs that are not in use. This includes programs that run in the background, such as screen savers and virus checkers. If you turn off your virus checker, remember to turn it back on after you finish your scan.
If this does not work, it might help to restart your computer. Some programs do not release memory when you close them. Restarting your computer will clear the memory.
If this problem occurs frequently, or if you encounter memory problems while using other programs, you might need to add more memory to your computer. See the user guide that came with your computer for more information.
244 Troubleshooting
Scan To menu does not appear
Cause: The Scan To menu does not appear if:
• The software that came with the HP All-in-One was not installed or necessary parts of it are not installed.
• The HP All-in-One is not connected to the computer.
• The computer is turned off.
• You closed the HP Digital Imaging Monitor icon in the Windows system tray on the taskbar.
Solution:
• Follow the directions in the Setup Poster to install the software that came with the
HP All-in-One.
• Make sure that the HP All-in-One is connected to a computer.
• If the HP All-in-One is directly connected to a computer, make sure the computer is turned on.
• Restart the computer or start the software you installed with the HP All-in-One.
Scan To menu does not appear
Cause: The Scan To menu does not appear if:
• The software that came with the HP All-in-One was not installed or necessary parts of it are not installed.
• The HP All-in-One is not connected to the computer.
• The computer is turned off.
Solution:
• Follow the directions in the Setup Poster to install the software that came with the
HP All-in-One.
• Make sure that the HP All-in-One is connected to a computer.
• If the HP All-in-One is directly connected to a computer, make sure the computer is turned on.
• Restart the computer or start the software you installed with the HP All-in-One.
Scanned image is blank
Cause: The original is placed incorrectly on the glass.
Scan troubleshooting 245
Chapter 11
Solution: Load the original print side down on the right front corner of the glass.
To load an original on the scanner glass
1.
Remove all originals from the document feeder tray, and then lift the lid on the
HP All-in-One.
2.
Load your original print side down on the right front corner of the glass.
3.
Close the lid.
Scanned image is incorrectly cropped
Cause: The software is set to automatically crop scanned pictures.
Solution: The Autocrop feature crops anything that is not part of the main image.
Sometimes this might not be what you want. In that case, you can turn off autocropping and crop the scanned image manually, or not at all.
You can change the Autocrop feature in the HP Scan Pro software. For more information, see the HP Scan Pro section of the HP Photosmart Mac Help.
Scanned image has incorrect page layout
Cause: Automatic cropping is changing the page layout.
Solution: Turn off automatic cropping to retain the page layout.
You can change the Autocrop feature in the HP Scan Pro software. For more information, see the HP Scan Pro section of the HP Photosmart Mac Help.
Scanned image shows dotted lines instead of text
Cause: If you use the Text image type to scan text that you plan to edit, the scanner might not recognize color text. The Text image type scans at 300 x 300 dpi, in black and white.
If you are scanning an original that has graphics or artwork surrounding the text, the scanner might not recognize the text.
246 Troubleshooting
Solution: Make a black-and-white copy of the original and then scan the copy.
Text format is incorrect
Cause: The scan document settings are incorrect.
Solution: Some programs cannot handle framed text formatting. Framed text is one of the scan document settings. It maintains complex layouts, such as multiple columns from a newsletter, by putting the text in different frames (boxes) in the destination application.
Text is incorrect or missing
Cause: The brightness is not set correctly.
Solution: Adjust the brightness, and then rescan the original.
You can adjust the brightness in the HP Scan Pro software. For more information, see the HP Scan Pro section of the HP Photosmart Mac Help.
Cause: Debris might be stuck on the glass or on the back of the document lid. This can cause poor-quality scans.
Solution: Turn off the HP All-in-One, unplug the power cord, and use a soft cloth to wipe the glass and the back of the document lid.
To clean the glass
1.
Turn off the HP All-in-One, and raise the lid.
2.
Clean the glass with a soft cloth or sponge slightly moistened with a nonabrasive glass cleaner.
CAUTION:
Do not use abrasives, acetone, benzene, or carbon tetrachloride on the glass, since they can damage it. Do not place or spray liquid directly on the glass. The liquid might seep under the glass and damage the device.
3.
Dry the glass with a dry, soft, lint-free cloth to prevent spotting.
4.
Turn on the HP All-in-One.
To clean the lid backing
1.
Turn off the HP All-in-One, unplug the power cord, and raise the lid.
NOTE:
Depending how long the HP All-in-One is unplugged, the date and time might be erased. You might need to reset the date and time later, when you plug the power cord back in.
2.
Clean the white document backing with a soft cloth or sponge slightly moistened with a mild soap and warm water.
Wash the backing gently to loosen debris. Do not scrub the backing.
Scan troubleshooting 247
Chapter 11
3.
Dry the backing with a dry, soft, lint-free cloth.
CAUTION:
Do not use paper-based wipes, as these might scratch the backing.
4.
If further cleaning is needed, repeat the previous steps using isopropyl (rubbing) alcohol, and wipe the backing thoroughly with a damp cloth to remove any residual alcohol.
CAUTION:
Be careful not to spill alcohol on the glass or exterior of the HP Allin-One, as this might damage the device.
The scan feature does not work
Cause: There are several reasons why a scan might not occur:
• The computer is turned off.
• The HP All-in-One is not properly connected to the computer through a USB cable.
• The software that came with the HP All-in-One is not installed or is not running.
Solution:
• Turn the computer on.
• Check the cables that connect the HP All-in-One to your computer.
• Restart your computer. If that does not help, install or reinstall the software that came with the HP All-in-One.
Device update
The function of device update is to deliver firmware updates to the HP All-in-One to keep your device running smoothly with the most advanced technology available.
To use device update
1.
Use your Web browser to download an update for the HP All-in-One from www.hp.com/support .
2.
Double-click the downloaded file.
The installer opens on your computer.
3.
Follow the onscreen prompts to install the update to the HP All-in-One.
4.
Restart the HP All-in-One to complete the process.
Errors
This section contains the following categories of messages on your device:
•
•
•
248 Troubleshooting
•
•
•
Device messages
The following is a list of device-related error messages:
•
Automatic document feeder failed to load
•
Automatic document feeder is jammed
•
•
•
•
•
•
Automatic document feeder failed to load
Cause: The automatic document feeder did not work properly, and the job did not finish.
Solution: Try loading the originals in the automatic document feeder again, and restart the job. Do not load more than 20 sheets in the document feeder tray.
Automatic document feeder is jammed
Cause: Paper has jammed the automatic document feeder.
Solution: Clear the paper jam and try the job again. Do not load more than 20 sheets of paper in the document feeder tray.
For information on clearing jams, see
.
Fax receive failed
Cause: An error caused a fax to fail while the HP All-in-One was receiving the fax.
The error could be due to noisy lines or some other communication error.
Solution: Contact the sender and request that the fax be sent again.
For more fax troubleshooting information, see Fax troubleshooting .
Fax send failed
Cause: The fax could not be completed because of a communication error, blacklisting (your number is blocked by the receiver), or a paper jam.
Solution: Check the HP All-in-One for a possible paper jam and send the fax again.
If the problem persists, try to contact the owner of the fax number for clarification.
For more information on clearing a paper jam, see Clear paper jams .
Errors 249
Chapter 11
For more fax troubleshooting information, see Fax troubleshooting .
Firmware revision mismatch
Cause: The revision number of the HP All-in-One firmware does not match the revision number of the software.
Solution: To find support and warranty information, go to the HP Web site at www.hp.com/support . If prompted, choose your country/region, and then click
Contact HP for information on calling for technical support.
Mechanism error
Cause: The HP All-in-One has a paper jam.
Solution: Clear the paper jam. Turn the HP All-in-One off and then turn it on again.
For information on clearing jams, see
.
CAUTION:
Trying to clear a paper jam from the front of the HP All-in-One can damage the print mechanism. Always access and clear paper jams through the rear door.
Cause: The print carriage is blocked or stalled.
Solution: Turn the HP All-in-One off, remove any objects that are blocking the print carriage (including any packing materials), and then turn the HP All-in-One on again.
Memory is full
Cause: While receiving a fax, the HP All-in-One jammed with paper or ran out of paper.
Solution: If the HP All-in-One supports faxing and you have Backup Fax
Reception enabled, the HP All-in-One might have stored the fax in memory upon reception.
After clearing the paper jam or loading paper in the input tray, you might be able to reprint the entire fax from memory. If you do not have Backup Fax Reception enabled, or if the fax was not stored in memory for some reason (for example, if the
HP All-in-One was out of memory), you will need to contact the sender and ask for the fax to be resent.
250 Troubleshooting
For more information on clearing paper jams, see Clear paper jams .
To load full-size paper
1.
Remove the output tray.
2.
Slide the paper-width guide to its outermost position.
3.
Tap a stack of paper on a flat surface to align the edges, and then check the paper for the following:
• Make sure it is free of rips, dust, wrinkles, and curled or bent edges.
• Make sure all the paper in the stack is the same size and type.
Errors 251
Chapter 11
4.
Insert the stack of paper into the input tray with the short edge forward and the print side down. Slide the stack of paper forward until it stops.
CAUTION:
Make sure that the HP All-in-One is idle and silent when you load paper into the input tray. If the HP All-in-One is servicing the print cartridges or otherwise engaged in a task, the paper stop inside the device might not be in place. You could push the paper too far forward, causing the HP All-in-One to eject blank pages.
TIP:
If you are using letterhead, insert the top of the page first with the print side down. For more help on loading full-size paper and letterhead, refer to the diagram engraved in the base of the input tray.
5.
Slide the paper-width guide inward until it stops at the edge of the paper.
Do not overload the input tray; make sure the stack of paper fits within the input tray and is no higher than the top of the paper-width guide.
6.
Replace the output tray.
252 Troubleshooting
7.
Flip the tray extender up toward you.
NOTE:
When you use legal-size paper, leave the tray extender closed.
To reprint faxes in memory from the control panel
1.
Make sure you have paper loaded in the input tray.
2.
Press Setup.
3.
Press 6, and then press 5.
This selects Tools and then selects Reprint Faxes in Memory.
The faxes are printed in the reverse order they were received with the most recently received fax printed first, and so on.
4.
If you want to stop reprinting the faxes in memory, press Cancel.
Cause: The document you are copying has exceeded the memory of the HP All-in-
One.
Solution: Try making fewer copies or, in the case of a multi-page document, copy fewer pages at a time.
Scanner failure
Cause: The HP All-in-One is busy or an unknown cause has interrupted your scan.
Solution: Turn off the HP All-in-One and then turn it on again. Restart your computer and then try to scan again.
File messages
The following is a list of file-related error messages:
•
Error reading or writing the file
•
•
•
Supported file types for the HP All-in-One
Error reading or writing the file
Cause: The HP All-in-One software could not open or save the file.
Errors 253
Chapter 11
Solution: Check to see if you typed the correct folder and file name.
File format not supported
Cause: The HP All-in-One software did not recognize or support the file format of the image you are trying to open or save. If the file extension indicates it is a supported file type, the file might be corrupted.
Solution: Open the file in another application, and save it in a format that the HP Allin-One software recognizes.
For more information about supported file types, see Supported file types for the
.
Invalid file name
Cause: The file name you entered is invalid.
Solution: Make sure that you are not using any invalid symbols in the file name.
Supported file types for the HP All-in-One
The HP All-in-One software recognizes the following file formats: BMP, DCX, FPX, GIF,
JPG, PCD, PCX, and TIF.
General user messages
The following is a list of messages related to common user errors:
•
•
•
•
•
•
Receiving fax machine did not answer
•
Receiving fax machine does not support color
Cannot crop
Cause: The computer does not have enough memory.
Solution: Close all unnecessary applications. This includes applications that run in the background, such as screensavers and virus checkers. (If you turn off your virus checker, remember to turn it back on after you finish.) Try restarting your computer to clear the memory. You might need to purchase more RAM. Refer to the documentation that came with your computer.
Cause: For scanning, there must be at least 50 MB of space available on your computer's hard disk.
254 Troubleshooting
Solution: Empty the Trash on your Mac. You might also need to remove files from the hard drive.
Dialed fax busy
Cause: The fax number you attempted to call is busy.
Solution: Wait and try to send the fax to the number at a later time.
Disconnected
Cause: Several situations can cause the Disconnected error message to appear.
• Your computer is not turned on.
• Your computer is not connected to the HP All-in-One.
• The HP software that came with the HP All-in-One was not installed correctly.
• The HP software is installed, but it is not running.
Solution: Make sure your computer is turned on and is connected to the HP All-in-
One. Also make sure you installed the software that came with the HP All-in-One.
No scan options
Cause: You did not install the software that came with the HP All-in-One, or the software is not running.
Solution: Make sure the software is installed and running. For more information, see the Setup Poster that came with the HP All-in-One.
Not supported
Cause: You tried to send a color fax from memory. The HP All-in-One does not support this procedure.
Solution: Try sending the color fax normally and not from memory.
Receiving fax machine did not answer
Cause: The receiving fax machine is not online, is turned off, is not functioning, or is not set to automatically answer incoming faxes.
For more fax troubleshooting information, see Fax troubleshooting .
Solution: Try to send the fax to the number again at a later time. If the problem persists, try to contact the owner of the fax number.
Receiving fax machine does not support color
Cause: You have tried to send a color fax to a fax machine that does not support color.
Errors 255
Chapter 11
Solution: The HP All-in-One alerts you to this situation and sends the color fax as black and white instead.
Paper messages
The following is a list of paper-related error messages:
•
Cannot load paper from input tray
•
•
•
Paper jam, misfeed or blocked carriage
•
•
Cannot load paper from input tray
Cause: There is not enough paper in the input tray.
Solution: If the HP All-in-One is out of paper or there are only a few sheets remaining, load more paper in the input tray. If there is paper in the input tray, remove the paper, tap the stack of paper against a flat surface, and reload the paper into the input tray. To continue your print job, press OK on the control panel of the HP All-in-
One.
Ink is drying
Cause: Transparencies and some other media require a drying time that is longer than normal.
Solution: Leave the sheet in the output tray until the message disappears. If it is necessary to remove the printed sheet before the message disappears, carefully hold the printed sheet on the underside or the edges, and place it on a flat surface to dry.
Out of paper
Cause: There is not enough paper in the input tray.
Solution: If the HP All-in-One is out of paper or there are only a few sheets remaining, load more paper in the input tray. If there is paper in the input tray, remove the paper, tap the stack of paper against a flat surface, and reload the paper into the input tray. To continue your print job, press OK on the control panel of the HP All-in-
One.
Cause: The rear door is off the HP All-in-One.
Solution: If you removed the rear door to clear a paper jam, replace it.
For more information on clearing jams, see
256 Troubleshooting
Paper jam, misfeed or blocked carriage
Cause: Paper has jammed the HP All-in-One or automatic document feeder.
Solution: Clear the jam.
For more information on clearing jams, see
CAUTION:
Trying to clear a paper jam from the front of the HP All-in-One can damage the print mechanism. Always access and clear paper jams through the rear door.
Cause: The print carriage is blocked.
Solution: Open the print cartridge door to access the print carriage area. Remove any objects that are blocking the print carriage, including any packing materials. Turn the HP All-in-One off and then turn it on again.
Paper mismatch
Cause: The print setting for the print job does not match the paper type or size loaded in the HP All-in-One.
Solution: Change the print setting or load the appropriate paper in the input tray.
To change all other print settings
1.
From the File menu in your software application, choose Print.
2.
Make sure the HP All-in-One is the selected printer.
3.
Make changes to the print settings, and click Print to print the job.
For more information on choosing paper, see
Understand specifications for supported media .
Wrong paper width
Cause: Faxing requires letter, A4, or legal paper.
Solution: Load letter, A4, or legal paper in the input tray.
Cause: The print setting chosen for the print job does not match the paper loaded in the HP All-in-One.
Solution: Change the print setting or load the appropriate paper in the input tray.
To change all other print settings
1.
From the File menu in your software application, choose Print.
2.
Make sure the HP All-in-One is the selected printer.
3.
Make changes to the print settings, and click Print to print the job.
For more information on choosing paper, see
Understand specifications for supported media .
Errors 257
Chapter 11
Power and connection messages
The following is a list of power- and connection-related error messages:
•
•
•
•
Communication test failed
Cause: The HP All-in-One is turned off.
Solution: Look at the display on the HP All-in-One. If the display is blank and the
Power button is not lit, the HP All-in-One is turned off. Make sure the power cord is firmly connected to the HP All-in-One and plugged into a power outlet. Press the
Power button to turn on the HP All-in-One.
Cause: The HP All-in-One is not connected to the computer.
Solution: If the HP All-in-One is not properly connected to the computer, communication errors can occur. Make sure the USB cable is securely connected to the HP All-in-One and the computer, as shown below.
HP All-in-One not found
Cause: The USB cable is not plugged in properly.
258 Troubleshooting
Solution: If the HP All-in-One is not properly connected to the computer, communication errors can occur. Make sure the USB cable is securely connected to the HP All-in-One and the computer, as shown below.
Improper shutdown
Cause: The last time the HP All-in-One was used, it was not turned off properly. If the HP All-in-One is turned off by turning off the switch on a power strip or by using a wall switch, the device can be damaged.
Solution: Press the Power button located on the control panel of the HP All-in-One to turn the device on and off.
Two-way communication lost
Cause: The HP All-in-One is turned off.
Solution: Look at the display on the HP All-in-One. If the display is blank and the
Power button is not lit, the HP All-in-One is turned off. Make sure the power cord is firmly connected to the HP All-in-One and plugged into a power outlet. Press the
Power button to turn on the HP All-in-One.
Cause: The HP All-in-One is not connected to the computer.
Errors 259
Chapter 11
Solution: If the HP All-in-One is not properly connected to the computer, communication errors can occur. Make sure the USB cable is securely connected to the HP All-in-One and the computer, as shown below.
Print cartridge messages
The following is a list of print cartridge error messages:
•
•
Need alignment or alignment failed
•
Print cartridge is missing, incorrectly installed, or not intended for your device
Low on ink
Cause: One or both print cartridges might be out of ink.
Solution: Check the estimated ink levels remaining in the print cartridges. If the print cartridges are low or out of ink, you might need to replace the print cartridges.
NOTE:
The HP All-in-One can only detect the ink levels for genuine HP ink. The ink levels in print cartridges that are refilled or have been used in other devices, might not register accurately.
If there is ink remaining in the print cartridges, but you are still noticing a problem, print a self-test report to determine if there is a problem with the print cartridges. If the self-test report shows a problem, clean the print cartridges. If the problem persists, you might need to replace the print cartridges.
NOTE:
Do not remove the old print cartridge until a new one is available.
For more information on print cartridges, see Print cartridge troubleshooting .
260 Troubleshooting
Need alignment or alignment failed
Cause: The incorrect type of paper is loaded in the input tray.
Solution: If you have colored paper loaded in the input tray when you align the print cartridges, the alignment fails. Load unused plain white letter or A4 paper into the input tray, and then try the alignment again. If the alignment fails again, you might have a defective sensor or print cartridge.
To find support and warranty information, go to the HP Web site at www.hp.com/ support . If prompted, choose your country/region, and then click Contact HP for information on calling for technical support.
Cause: Protective tape is covering the print cartridges.
Solution: Check each print cartridge. The tape might have been removed from the copper-colored contacts, but still might cover the ink nozzles. If the tape is still covering the ink nozzles, carefully remove the tape from the print cartridges. Do not touch the ink nozzles or the copper-colored contacts.
1 Copper-colored contacts
2 Plastic tape with pink pull tab (must be removed before installing)
3 Ink nozzles under tape
Reinsert the print cartridges and verify that they are fully inserted and locked in place.
Cause: The contacts on the print cartridge are not touching the contacts in the print carriage.
Solution: Remove and then reinsert the print cartridges. Verify that they are fully inserted and locked in place.
Cause: The print cartridge or sensor is defective.
Errors 261
Chapter 11
Solution: To find support and warranty information, go to the HP Web site at www.hp.com/support . If prompted, choose your country/region, and then click
Contact HP for information on calling for technical support.
Cause: You installed new print cartridges which might need alignment.
Solution: You must align the print cartridges to ensure excellent print quality. After you insert a new print cartridge, load letter or A4 unused plain white paper into the input tray, and then press OK on the control panel. The HP All-in-One prints a print cartridge alignment sheet and aligns the print cartridges. Recycle or discard the page.
If the alignment page prints properly, showing green check marks on each line, but the alignment error persists, you can clear the message by pressing OK and Setup at the same time.
If the alignment error persists and you cannot clear it , your print cartridge might be defective. Contact HP for support.
To find support and warranty information, go to the HP Web site at www.hp.com/ support . If prompted, choose your country/region, and then click Contact HP for information on calling for technical support.
Print cartridge is missing, incorrectly installed, or not intended for your device
Cause: One or both of the print cartridges are not installed or are installed incorrectly.
Solution: For more information on print cartridges, see Print cartridge troubleshooting .
Cause: The print cartridge is missing.
Solution: For more information on print cartridges, see Print cartridge troubleshooting .
Cause: Protective tape is covering the print cartridges.
Solution: Check each print cartridge. The tape might have been removed from the copper-colored contacts, but still might cover the ink nozzles. If the tape is still
262 Troubleshooting
covering the ink nozzles, carefully remove the tape from the print cartridges. Do not touch the ink nozzles or the copper-colored contacts.
1 Copper-colored contacts
2 Plastic tape with pink pull tab (must be removed before installing)
3 Ink nozzles under tape
Cause: The print cartridge is defective or not intended for use in this device.
Solution: To find support and warranty information, go to the HP Web site at www.hp.com/support . If prompted, choose your country/region, and then click
Contact HP for information on calling for technical support.
Errors 263
Chapter 11
264 Troubleshooting
12 Order supplies
You can order HP products, such as recommended types of paper and print cartridges, online from the HP website.
This section contains the following topics:
•
•
•
Order paper or other media
To order HP papers and other supplies, such as HP Premium Photo Papers or HP Allin-One Paper, go to www.hp.com/learn/suresupply . If prompted, choose your country/ region, follow the prompts to select your product, and then click one of the shopping links on the page.
Order print cartridges
For a list of print cartridge numbers, see the back cover of this guide. You can also use the software that came with the HP All-in-One to find out the reorder number for all the print cartridges. You can order print cartridges online from the HP website. Additionally, you can contact a local HP reseller to find out the correct print cartridge reorder numbers for your device and purchase print cartridges.
To order HP papers and other supplies, go to www.hp.com/learn/suresupply . If prompted, choose your country/region, follow the prompts to select your product, and then click one of the shopping links on the page.
NOTE:
Ordering print cartridges online is not supported in all countries/regions. If it is not supported in your country/region, contact a local HP reseller for information about purchasing print cartridges.
To find out the reorder number through the HP Photosmart Studio (Mac) Software
1.
In the HP Photosmart Studio task bar, click Devices.
The HP Device Manager window appears.
2.
Make sure the HP All-in-One is selected in the Devices pop-up menu.
3.
From the Information and Settings pop-up menu, choose Maintain Printer.
The Select Printer window appears.
4.
If the Select Printerdialog box appears, choose the HP All-in-One, and click Launch
Utility.
The HP Printer Utility window appears.
5.
In the Configuration Settings list, click Supply Info.
The print cartridge reorder numbers appear.
6.
If you want to order print cartridges, click Supplies Status in the Configuration
Settings area, and then click Order HP Supplies.
Order supplies 265
Chapter 12
Order other supplies
To order other supplies, such as HP All-in-One software, a copy of the Setup Poster or other printed documentation, or other customer-replaceable parts, call the phone number for your country/region.
Country/region
Asia Pacific (except for Japan)
Australia
Europe
New Zealand
South Africa
U.S. and Canada
Number for ordering
65 272 5300
1300 721 147
+49 180 5 290220 (Germany)
+44 870 606 9081 (U.K.)
0800 441 147
+27 (0)11 8061030
1-800-474-6836 (1-800-HP-INVENT)
To order supplies in other countries/regions not listed in the table, go to www.hp.com/ support . If prompted, choose your country/region, and then click Contact HP for information on calling for technical support.
266 Order supplies
13 HP warranty and support
Hewlett-Packard provides Internet and phone support for the HP All-in-One.
This section contains the following topics:
•
•
Get support and other information from the Internet
•
Before you call HP customer support
•
Access your serial number and service ID
•
Call in North America during warranty
•
•
HP Quick Exchange Service (Japan)
•
Prepare the HP All-in-One for shipment
•
Warranty
To obtain HP repair service, you must first contact an HP service office or an HP Customer Support
Center for basic troubleshooting. See Before you call HP customer support
for steps to take before calling Customer Support.
NOTE:
This information does not apply to customers in Japan. For information on service options in Japan, see
HP Quick Exchange Service (Japan)
.
For more information about the warranty, see the printed documentation that came with the HP Allin-One.
Warranty upgrades
Depending on your country/region, HP might offer (for an additional fee) a warranty upgrade option that extends or enhances your standard product warranty. Available options might include priority phone support, return service, or next business day exchange. Typically, service coverage begins on product purchase date and must be purchased within a limited time of product purchase.
For more information, see:
• In the U.S., dial 1-866-234-1377 to speak to an HP advisor.
• Outside the U.S., please call your local HP Customer Support office. See
Call elsewhere in the world for a list of international Customer Support numbers.
• Go to the HP website at www.hp.com/support . If prompted, choose your country/region, and then find warranty information.
Get support and other information from the Internet
To find support and warranty information, go to the HP website at www.hp.com/support . If prompted, choose your country/region, and then click Contact HP for information on calling for technical support.
This website also offers technical support, drivers, supplies, ordering information and other options such as:
• Access online support pages.
• Send HP an e-mail message for answers to your questions.
• Connect with an HP technician by using online chat.
• Check for software updates.
Support options and availability vary by product, country/region, and language.
HP warranty and support 267
Chapter 13
Before you call HP customer support
Software programs from other companies might be included with the HP All-in-One. If you experience problems with any of those programs, you will receive the best technical assistance by calling the experts at that company.
NOTE:
This information does not apply to customers in Japan. For information on service options in Japan, see
HP Quick Exchange Service (Japan)
.
If you need to contact HP Customer Support, do the following before you call:
1.
Make sure that:
a. The HP All-in-One is plugged in and turned on.
b. The specified print cartridges are installed correctly.
c. The recommended paper is properly loaded in the input tray.
2.
Reset the HP All-in-One:
a. Turn off the HP All-in-One by pressing the Power button.
b. Unplug the power cord from the back of the HP All-in-One.
c. Plug the power cord back into the HP All-in-One.
d. Turn on the HP All-in-One by pressing the Power button.
3.
To find support and warranty information, go to the HP website at www.hp.com/support . If prompted, choose your country/region, and then click Contact HP for information on calling for technical support.
Check the HP website for updated information or troubleshooting tips for the HP All-in-One .
4.
If you are still experiencing problems and need to speak with an HP Customer Support
Representative, do the following:
a. Have the specific name of the HP All-in-One, as it appears on the control panel, available.
b. Print a self-test report.
c. Make a color copy to have available as a sample printout.
d. Be prepared to describe your problem in detail.
e. Have your serial number and service ID ready.
5.
Call HP Customer Support. Be near the HP All-in-One when you call.
Related topics
•
•
Access your serial number and service ID
Access your serial number and service ID
You can access important information by using the Information Menu of the HP All-in-One.
NOTE:
If the HP All-in-One is not turning on, you can view the serial number by looking at the sticker on the rear side. The serial number is the 10-character code in the upper left corner of the sticker.
To access your serial number and service ID
1.
Press and hold OK. While holding OK, press 4. This displays the Information Menu.
2.
Press until Model Number appears and then press OK. This displays the service ID.
Write down the complete service ID.
3.
Press Cancel, and then press until Serial Number appears.
4.
Press OK. This displays the serial number.
Write down the complete serial number.
5.
Press Cancel until you to exit the Information Menu.
268 HP warranty and support
Call in North America during warranty
Call 1-800-474-6836 (1-800-HP invent). U.S. and Canada phone support is available in both English and Spanish languages 24 hours a day, 7 days a week (days and hours of support may change without notice). This service is free during the warranty period. A fee may apply outside the warranty period.
Call elsewhere in the world
To find support and warranty information, go to the HP website at www.hp.com/support . If prompted, choose your country/region, and then click Contact HP for information on calling for technical support.
Alternatively, you can ask your dealer for the HP Support Service number in your country/region.
Support service is free during the warranty period; however, your standard long-distance phone charges might apply. In some cases, per minute, per half-minute or a flat fee per single incident might also apply.
As part of our constant efforts to improve our phone support service, we advise you to check our website on a regular basis for new information regarding service features and delivery.
Call in North America during warranty 269
Chapter 13
270 HP warranty and support
HP Quick Exchange Service (Japan)
For instructions on how to pack your device for exchange, see Pack the HP All-in-One .
Prepare the HP All-in-One for shipment
If after contacting HP Customer Support or returning to the point of purchase, you are requested to send the HP All-in-One in for service, make sure you remove and keep the following items before returning your device:
• The print cartridges
• The control panel faceplate
• The power cord, USB cable, and any other cable connected to the HP All-in-One
• Any paper loaded in the input tray
• Remove any originals you might have loaded in the HP All-in-One
This section contains the following topics:
•
Remove the print cartridges before shipment
•
Remove the control panel faceplate
Remove the print cartridges before shipment
Before you return the HP All-in-One, make sure you remove your print cartridges.
NOTE:
This information does not apply to customers in Japan. For information on service options in Japan, see
HP Quick Exchange Service (Japan)
.
HP Quick Exchange Service (Japan) 271
Chapter 13
To remove print cartridges before shipment
1.
Turn on the HP All-in-One and wait until the print carriage is idle and silent. If the HP All-in-One will not turn on, skip this step and go to step 2.
2.
Open the print cartridge door.
3.
Remove the print cartridges from their slots.
NOTE:
If the HP All-in-One does not turn on, you can unplug the power cord and then manually slide the print carriage to the far right side to remove the print cartridges.
4.
Place the print cartridges in an airtight plastic container so they will not dry out, and put them aside. Do not send them with the HP All-in-One unless the HP customer support call agent instructs you to.
5.
Close the print cartridge door and wait a few minutes for the print carriage to move back to its home position (on the left side).
NOTE:
Make sure the scanner is idle and has returned to its parked position before turning off the HP All-in-One.
6.
Press the Power button to turn off the HP All-in-One.
Remove the control panel faceplate
Complete the following steps once you have removed the print cartridges.
NOTE:
This information does not apply to customers in Japan. For information on service options in Japan, see
HP Quick Exchange Service (Japan)
.
CAUTION:
The HP All-in-One must be unplugged before following these steps.
CAUTION:
The replacement HP All-in-One will not be shipped with a power cord. Store the power cord in a safe place until the replacement HP All-in-One arrives.
To remove the control panel faceplate
1.
Press the Power button to turn off the HP All-in-One.
2.
Unplug the power cord, and then disconnect it from the HP All-in-One. Do not return the power cord with the HP All-in-One.
3.
Lift the ADF lid.
4.
Remove the control panel faceplate as follows:
a. Place your hands on each side of the control panel faceplate.
b. Use your fingertip or insert a thin object in the tab on the upper right corner of the faceplate to pry the control panel faceplate off.
272 HP warranty and support
5.
Retain the control panel faceplate. Do not return the control panel faceplate with the HP All-in-
One.
CAUTION:
The replacement HP All-in-One might not come with a control panel faceplate.
Store your control panel faceplate in a safe place, and when the replacement HP All-in-One arrives, reattach your control panel faceplate. You must attach your control panel faceplate to use the control panel functions on the replacement HP All-in-One.
NOTE:
See the Setup Poster that came with the HP All-in-One for instructions on how to attach your control panel faceplate. The replacement HP All-in-One might come with instructions for setting up your device.
Pack the HP All-in-One
Complete the following steps once you have removed the print cartridges, removed the control panel faceplate, turned off the HP All-in-One, and unplugged it.
To pack the HP All-in-One
1.
If available, pack the HP All-in-One for shipment by using the original packing materials or the packaging materials that came with your exchange device.
If you do not have the original packaging materials, please use other adequate packaging materials. Shipping damage caused by improper packaging and/or improper transportation is not covered under the warranty.
2.
Place the return shipping label on the outside of the box.
3.
Include the following items in the box:
• A complete description of symptoms for service personnel (samples of print quality problems are helpful).
• A copy of the sales slip or other proof of purchase to establish the warranty coverage period.
• Your name, address, and a phone number where you can be reached during the day.
Pack the HP All-in-One 273
Chapter 13
274 HP warranty and support
14 Technical information
The technical specifications and international regulatory information for the HP All-in-One are provided in this section.
•
•
•
•
•
•
•
•
•
•
•
Environmental product stewardship program
•
•
Declaration of conformity (European Economic Area)
•
HP Officejet J5700 All-in-One series declaration of conformity
System requirements
NOTE:
For the most current information about supported operating systems and system requirements, visit www.hp.com/support .
Operating system compatibility
• Windows 2000, Windows XP, Windows XP x64* (Professional and Home Editions)
• Mac OS X (10.3, 10.4)
• Linux
NOTE:
Printer and scanner drivers for Windows Server 2003 (both 32-bit and 64-bit versions) require a minimum of an Intel Pentium II or Celeron processor, 128 MB RAM, 200 MB free hard disk space. The drivers are available at http://www.hp.com/support/ .
Minimum requirements
• Windows 2000: Intel Pentium II or Celeron processor, 128 MB RAM, 280 MB free hard disk space
• Windows XP (32-bit): Intel Pentium II or Celeron processor, 128 MB RAM, 280 MB free hard disk space
• Windows XP x64: Intel Pentium II or Celeron processor, 128 MB RAM, 280 MB free hard disk space
• Mac OS X (10.3.8, 10.4.x): 400 MHz Power PC G3 (v10.3.8 and v10.4.x) or 1.83 GHz Intel Core
Duo (v10.4.x), 128 MB memory, 300 MB free hard disk space
•
Microsoft Internet Explorer 6.0
Technical information 275
Chapter 14
Recommended requirements
• Windows 2000: Intel Pentium III or higher processor, 256 MB RAM, 500 MB free hard disk space
• Windows XP (32-bit): Intel Pentium III or higher processor, 256 MB RAM, 500 MB free hard disk space
• Windows XP x64: Intel Pentium III or higher processor, 256 MB RAM, 500 MB free hard disk space
• Mac OS X (10.3.8, 10.4.x): 400 MHz Power PC G3 (v10.3.8 and v10.4.x) or 1.83 GHz Intel Core
Duo (v10.4.x), 256 MB memory, 600 MB free hard disk space
•
Microsoft Internet Explorer 6.0 or later
Paper specifications
This section contains information about paper tray capacities, paper sizes, and print margin specifications.
•
•
•
Paper tray capacities
Type Paper weight Input tray
Document feeder tray
Plain paper
Legal paper
16 to 24 lb. (60 to
90 gsm)
20 to 24 lb. (75 to
90 gsm) up to 100
(20 lb. paper) up to 100
(20 lb. paper)
40 up to 50
(20 lb. paper) up to 50
(20 lb. paper)
10 up to 35 up to 20
Cards
Envelopes
Transparency film
Labels up to 110 lb.
index (200 gsm)
20 to 24 lb. (75 to
90 gsm)
N/A
N/A
15
25
20
10
25 or fewer
20
N/A
N/A
N/A
N/A
4 x 6 inch photo paper up to 145 lb. (236 gsm)
30 10 N/A
8.5 x 11 inch photo paper
N/A 40 20 N/A
1 Maximum capacity.
2 Output tray capacity is affected by the type of paper and the amount of ink you are using.
HP recommends emptying the output tray frequently.
Paper sizes
Type
Paper
Size
Letter: 216 x 280 mm (8.5 x 11 inches)
A4: 210 x 297 mm
276 Technical information
(continued)
Type
Envelopes
Transparency film
Premium photo paper
Cards
Labels
Custom
Size
Legal: 216 x 356 mm (8.5 x 14 inches)
U.S. #10: 105 x 241 mm (4.125 x 9.5 inches)
U.S. #9: 98 x 225 mm (3.9 x 8.9 inches)
A2: 111 x 146 mm (4.4 x 5.8 inches)
DL: 110 x 220 mm (4.3 x 8.7 inches)
C6: 114 x 162 mm (4.5 x 6.4 inches)
Letter: 216 x 279 mm (8.5 x 11 inches)
A4: 210 x 297 mm
102 x 152 mm (4 x 6 inches)
Letter: 216 x 280 mm (8.5 x 11 inches)
A4: 210 x 297 mm
A6: 105 x 148.5 mm
Index card: 76 x 127 mm (3 x 5 inches)
Index card: 101 x 152 mm (4 x 6 inches)
Letter: 216 x 279 mm (8.5 x 11 inches)
A4: 210 x 297 mm
102 x 152 mm up to 216 x 356 mm (4 x 6 inches up to 8.5 x 14 inches)
Print margin specifications
Top (leading edge) Bottom (trailing edge)
1.8 mm (0.07 inches) 2 mm (0.12 inches) U.S. Letter
U.S. Legal
A4
Photo media
U.S. Executive
B5
A5
Cards
Envelopes
1.8 mm (0.07 inches) 6 mm (0.24 inches)
16.5 mm (0.65
inches)
16.5 mm (0.66
inches)
Left and Right margins
2 mm (0.12 inches)
2 mm (0.12 inches)
3.3 mm (0.13 inches)
Print specifications
• Resolution: 1200 x 1200 dpi black, 4800 optimized dpi color or 6 ink
• Method: drop-on-demand thermal inkjet
• Language: Lightweight Imaging Device Interface Language (LIDIL)
• Print speed varies according to the complexity of the document
Print specifications 277
Chapter 14
Copy specifications
• Digital image processing
• Up to 100 copies from original (varies by model)
• Digital zoom: from 25 to 400% (varies by model)
• Fit to page, pre-scan
• Copy speeds vary according to the complexity of the document
Mode Type
Best
Normal
Black
Color
Black
Fast
Color
Black
Color
1 Maximum at 400% scaling.
Scan resolution
(dpi)
up to 600 x 1200 up to 600 x 1200 up to 300 x 300 up to 300 x 300 up to 300 x 300 up to 300 x 300
Fax specifications
• Walk-up black-and-white and color fax capability.
• Up to 110 speed dials (varies by model).
• Up to 120-page memory (varies by model, based on ITU-T Test Image #1 at standard resolution). More complicated pages or higher resolution takes longer and uses more memory.
• Manual fax send and receive.
• Automatic busy redial up to five times (varies by model).
• Automatic no-answer redial one time (varies by model).
• Confirmation and activity reports.
• CCITT/ITU Group 3 fax with Error Correction Mode.
• 33.6 Kbps transmission.
• 3 seconds per page speed at 33.6 Kbps (based on ITU-T Test Image #1 at standard resolution).
More complicated pages or higher resolution take longer and use more memory.
• Ring detect with automatic fax/answering machine switching.
Black
Color
Photo (dpi)
196 x 203 (8-bit grayscale)
200 x 200
Very Fine (dpi)
300 x 300
200 x 200
Fine (dpi)
196 x 203
200 x 200
Standard (dpi)
196 x 98
200 x 200
Scan specifications
• Image editor included
• Integrated OCR software automatically converts scanned text to editable text
• Scan speeds vary according to the complexity of the document
• Twain-compliant interface
• Resolution: 2400 x 4800 ppi optical, up to 19,200 ppi enhanced
278 Technical information
• Color: 16-bit per RGB color, 48-bit total
• Maximum scan size from glass: 216 x 297 mm (8.5 x 11.7 inches)
Physical specifications
• Height: 236 mm (9.29 inches)
• Width: 456 mm (17.95 inches)
• Depth: 326 mm (12.83 inches)
• Weight: 7.66 kg (16.9 pounds)
Power specifications
• Maximum power consumption: 40 W (average printing)
• Idle state power consumption: 6.5 W
• Power supply's input voltage: AC 100 to 240 VAC, 1A, 50-60 Hz, grounded
• System DC input: 16 Vdc at 500 mA, 32 Vdc at 700 mA
NOTE:
The AC adaptor shipped might be specified to provide more power than system
DC input (max) requirement above.
Environmental specifications
• Recommended operating temperature range: 15º to 32º C (59º to 90º F)
• Allowable operating temperature range: 5º to 40º C (41º to 104º F)
• Humidity: 15% to 80% RH non-condensing
• Non-operating (Storage) temperature range: -40º to 60º C (-40º to 140º F)
In the presence of high electromagnetic fields it is possible the output from the HP All-in-One might be slightly distorted.
HP recommends using a USB cable less than or equal to 3 m (10 feet) in length to minimize injected noise due to potential high electromagnetic fields.
If you have Internet access, you can get acoustic information from the HP website. Go to www.hp.com/support .
Memory specifications
Memory specifications: 8 MB ROM, 32 MB DDR
Environmental product stewardship program
This section provides information on protecting the environment; ozone production; energy consumption; paper use; plastics; material safety data sheets; and recycling programs.
This section contains information about environmental standards.
•
•
•
•
•
•
•
HP inkjet supplies recycling program
•
Disposal of Waste Equipment by Users in Private Households in the European Union
Physical specifications 279
Chapter 14
Protecting the environment
Hewlett-Packard is committed to providing quality products in an environmentally sound manner.
This product has been designed with several attributes to minimize impacts on our environment.
For more information, visit HP’s Commitment to the Environment website at: www.hp.com/hpinfo/globalcitizenship/environment/index.html
Ozone production
This product generates no appreciable ozone gas (O3).
Paper use
This product is suited for the use of recycled paper according to DIN 19309.
Plastics
Plastic parts over 25 grams are marked according to international standards that enhance the ability to identify plastics for recycling purposes at the end of the product’s life.
Material safety data sheets
Material safety data sheets (MSDS) can be obtained from the HP website at: www.hp.com/go/msds
Customers without Internet access should contact their local HP Customer Care Center.
Hardware recycling program
HP offers an increasing number of product return and recycling programs in many countries, as well as partnering with some of the largest electronic recycling centers throughout the world. HP also conserves resources by refurbishing and reselling some of its most popular products.
For information regarding recycling of HP products, please visit: www.hp.com/recycle .
HP inkjet supplies recycling program
HP is committed to protecting the environment. The HP Inkjet Supplies Recycling Program is available in many countries/regions, and lets you recycle used print cartridges free of charge. For more information, go to the following website: www.hp.com/recycle
Disposal of Waste Equipment by Users in Private Households in the European
Union
This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service, or the shop where you purchased the product.
280 Technical information
Regulatory notices
The HP All-in-One meets product requirements from regulatory agencies in your country/region.
•
Regulatory model identification number
•
Notice to users of the U.S. telephone network: FCC requirements
•
•
Note à l’attention des utilisateurs du réseau téléphonique canadien/notice to users of the
•
•
•
Notice to users in the European Economic Area
•
Notice to users of the German telephone network
•
•
•
Regulatory model identification number
For regulatory identification purposes, your product is assigned a Regulatory Model Number. The
Regulatory Model Number for your product is SDGOB-0701. This regulatory number should not be confused with the marketing name HP Officejet J5700 All-in-One series.
Notice to users of the U.S. telephone network: FCC requirements
This equipment complies with FCC rules, Part 68. On this equipment is a label that contains, among other information, the FCC Registration Number and Ringer Equivalent Number (REN) for this equipment. If requested, provide this information to your telephone company.
An FCC compliant telephone cord and modular plug is provided with this equipment. This equipment is designed to be connected to the telephone network or premises wiring using a compatible modular jack which is Part 68 compliant. This equipment connects to the telephone network through the following standard network interface jack: USOC RJ-11C.
The REN is useful to determine the quantity of devices you may connect to your telephone line and still have all of those devices ring when your number is called. Too many devices on one line might result in failure to ring in response to an incoming call. In most, but not all, areas the sum of the RENs of all devices should not exceed five (5). To be certain of the number of devices you may connect to your line, as determined by the REN, you should call your local telephone company to determine the maximum REN for your calling area.
If this equipment causes harm to the telephone network, your telephone company may discontinue your service temporarily. If possible, they will notify you in advance. If advance notice is not practical, you will be notified as soon as possible. You will also be advised of your right to file a complaint with the FCC. Your telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the proper operation of your equipment. If they do, you will be given advance notice so you will have the opportunity to maintain uninterrupted service.
If you experience trouble with this equipment, please contact the manufacturer, or look elsewhere in this manual, for warranty or repair information. Your telephone company may ask you to disconnect this equipment from the network until the problem has been corrected or until you are sure that the equipment is not malfunctioning.
This equipment may not be used on coin service provided by the telephone company. Connection to party lines is subject to state tariffs. Contact your state public utility commission, public service commission, or corporation commission for more information.
Regulatory notices 281
Chapter 14
This equipment includes automatic dialing capability. When programming and/or making test calls to emergency numbers:
• Remain on the line and explain to the dispatcher the reason for the call.
• Perform such activities in the off-peak hours, such as early morning or late evening.
NOTE:
The FCC hearing aid compatibility rules for telephones are not applicable to this equipment.
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, including fax machines, to send any message unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of transmission, the date and time it is sent and an identification of the business, other entity, or other individual sending the message and the telephone number of the sending machine or such business, other entity, or individual. (The telephone number provided may not be a 900 number or any other number for which charges exceed local or long-distance transmission charges.) In order to program this information into your fax machine, you should complete the steps described in the software.
FCC statement
The United States Federal Communications Commission (in 47 CFR 15.105) has specified that the following notice be brought to the attention of users of this product.
Declaration of Conformity: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that might cause undesired operation. Class B limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, might cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
For more information, contact the Product Regulations Manager, Hewlett-Packard Company, San
Diego, (858) 655-4100.
The user may find the following booklet prepared by the Federal Communications Commission helpful: How to Identify and Resolve Radio-TV Interference Problems. This booklet is available from the U.S. Government Printing Office, Washington DC, 20402. Stock No. 004-000-00345-4.
CAUTION:
Pursuant to Part 15.21 of the FCC Rules, any changes or modifications to this equipment not expressly approved by the Hewlett-Packard Company might cause harmful interference and void the FCC authorization to operate this equipment.
Note à l’attention des utilisateurs du réseau téléphonique canadien/notice to users of the Canadian telephone network
Cet appareil est conforme aux spécifications techniques des équipements terminaux d’Industrie
Canada. Le numéro d’enregistrement atteste de la conformité de l’appareil. L’abréviation IC qui précède le numéro d’enregistrement indique que l’enregistrement a été effectué dans le cadre d’une
Déclaration de conformité stipulant que les spécifications techniques d’Industrie Canada ont été respectées. Néanmoins, cette abréviation ne signifie en aucun cas que l’appareil a été validé par
Industrie Canada.
282 Technical information
Pour leur propre sécurité, les utilisateurs doivent s’assurer que les prises électriques reliées à la terre de la source d’alimentation, des lignes téléphoniques et du circuit métallique d’alimentation en eau sont, le cas échéant, branchées les unes aux autres. Cette précaution est particulièrement importante dans les zones rurales.
Le numéro REN (Ringer Equivalence Number) attribué à chaque appareil terminal fournit une indication sur le nombre maximal de terminaux qui peuvent être connectés à une interface téléphonique. La terminaison d’une interface peut se composer de n’importe quelle combinaison d’appareils, à condition que le total des numéros REN ne dépasse pas 5.
Basé sur les résultats de tests FCC Partie 68, le numéro REN de ce produit est 0.1B.
This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications.
This is confirmed by the registration number. The abbreviation IC before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that
Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together.
This precaution might be particularly important in rural areas.
NOTE:
The REN assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface might consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.
The REN for this product is 0.1B, based on FCC Part 68 test results.
Notice to users in Japan
VCCI-2
Power cord statement
The power cord cannot be repaired. If it is defective, it should be discarded or returned to the supplier.
Notice to users in the European Economic Area
This product is designed to be connected to the analog Switched Telecommunication Networks
(PSTN) of the European Economic Area (EEA) countries/regions.
Regulatory notices 283
Chapter 14
Network compatibility depends on customer selected settings, which must be reset to use the equipment on a telephone network in a country/region other than where the product was purchased.
Contact the vendor or Hewlett-Packard Company if additional product support is necessary.
This equipment has been certified by the manufacturer in accordance with Directive 1999/5/EC
(annex II) for Pan-European single-terminal connection to the public switched telephone network
(PSTN). However, due to differences between the individual PSTNs provided in different countries, the approval does not, of itself, give an unconditional assurance of successful operation on every
PSTN network termination point.
In the event of problems, you should contact your equipment supplier in the first instance.
This equipment is designed for DTMF tone dialing and loop disconnect dialing. In the unlikely event of problems with loop disconnect dialing, it is recommended to use this equipment only with the
DTMF tone dial setting.
Notice to users of the German telephone network
This HP fax product is designed to connect only to the analogue public-switched telephone network
(PSTN). Please connect the TAE N telephone connector plug, provided with the HP All-in-One into the wall socket (TAE 6) code N. This HP fax product can be used as a single device and/or in combination (in serial connection) with other approved terminal equipment.
Geräuschemission
LpA < 70 dB am Arbeitsplatz im Normalbetrieb nach DIN 45635 T. 19
Notice to users in Korea
Australia Wired Fax Statement
Declaration of conformity (European Economic Area)
The Declaration of Conformity in this document complies with ISO/IEC Guide 17050-1 and EN
17050-1. It identifies the product, manufacturer's name and address, and applicable specifications recognized in the European community.
284 Technical information
HP Officejet J5700 All-in-One series declaration of conformity
HP Officejet J5700 All-in-One series declaration of conformity 285
Chapter 14
286 Technical information
Index
Symbols/Numerics
10 x 15 cm photo paper
4 x 6 inch photo paper
4 x 6 inch photo paper, load 66
A
ADF (automatic document feeder)
ADSL. See DSL
alignment
failed 261 print cartridges 261
answering machine
answering machine, set up with
automatic document feeder
feeding problems,
automatic document feeder
(ADF)
B
blank
blank pages
blurry
borderless photos
C
calling card, fax using 93, 94
cancel
capacity
cards
cartridges. See print cartridges clean automatic document
print cartridge ink nozzle
color
communication problems
two-way communication
computer modem
computer modem, set up with
connection problems
HP All-in-One does not turn
connection types supported
control panel
copy
number of copies 74 paper size 74
paper types,
287
too dark 233 too light 233 troubleshooting 233
crop borderless copy is
custom-sized media
customer support
HP Quick Exchange Service
North America 269 outside U.S. 269
serial number 268 service ID 268
D
darken
declaration of conformity
European Economic
default settings
delete
destinations
add 86 automatic mode 86 change 86 change image type 86 change resolution 86 edit properties 86
device
device update
dial-up modem. See computer modem
display
distinctive ringing 32, 45, 47
documents
duplexer
media types and weights
E
ECM. See error correction mode edit
envelopes
environment
Environmental product
environmental
error messages
European Union
F
fax
288 answering machine, set
computer modem, set
distinctive ringing 32, 45, 47
143, 146, 153, 157, 158 problems receiving 158,
Index
send to multiple
fax problems
FCC
file
invalid name 254 supported formats 254 unsupported formats 254
firmware revision mismatch 250
forward
G
glass
H
help
HP Photosmart Software
I
images
individual speed dial entries 49
ink
sprays inside HP All-in-
ink cartridges. See print cartridges
IP
J
jams
K
L
labels
legal paper
letter paper
light
lighten
load
legal paper 63 letter paper 63
M
Mac OS
maintenance
clean glass 117 clean lid backing 117
manual
margins
media
specifications 58 supported sizes 58
types and weights
memory
289
missing
modem. See computer modem
N
O
one-touch speed dial
operating systems
order
paper 265 print cartridges 265
output tray
P
paper
recommended copy
type incorrect 257 width incorrect 257
paper size
PBX system, set up with fax 31
PC modem. See computer modem phone
phone cord
check 227 connection, failure 227
phone line, answer ring
phone numbers, customer
photo media
photo paper
photos
preview image defaults 86 skip preview image 86
poor fax printout quality 142,
poor print quality
preview image
set defaults 86 skip 86 preview image, edit 86
envelopes print
from computer 71 from software application 71
print cartridges
print margin specifications 277
print settings
printer sharing
problems
Q
290
Index
R
receive fax
recycle
HP All-in-One 280 print cartridges 280
reduce/enlarge copies
regulatory notices
declaration of conformity
(European Economic
declaration of conformity
notice to users in Japan
notice to users in the
European Economic
notice to users of the
German telephone
regulatory model
reports
confirmation, fax 112 error, fax 112
fax log 113 junk fax numbers 113 last fax transaction 113 log, fax 113
S
save
scan
cancel 86 change default settings 86
features 85 from control panel 85
preview image, edit 86 print 86
text appears as dotted
text format incorrect 247 text incorrect 247
scan glass
send fax
credit card, using 93, 94 manually 93, 94
settings
setup
software
software application, print
software program, send fax
specifications
speed
speed dial
291
start copy
start fax
stop
subscriber identification
T
technical information
environmental
paper sizes 276 paper specifications 276 paper tray capacities 276
physical specifications 279 power specifications 279
print margin
specifications 277 print specifications 277
telephone
telephone line, answer ring
telephone numbers, customer
telephone wall jack test, fax 226
test
text
incorrect format on
incorrect or missing on
transparencies
tray 1
media types and weights
trays
media types and weights
troubleshoot
troubleshooting communication
U
USB cable
V
voice mail
voice mail, set up with fax 45,
W
Windows
292
© 2007 Hewlett-Packard Development Company, L.P.
www.hp.com
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Key Features
- All-in-one functionality: Print, scan, copy, and fax
- Compact and affordable design
- User-friendly control panel
- Intuitive software
- Fast printing speeds
- High-quality scanning and copying
- Built-in fax modem
- Automatic document feeder
Related manuals
Frequently Answers and Questions
How do I set up the HP Officejet J5700 All-in-One Printer series?
How do I print a document?
How do I scan a document?
How do I copy a document?
How do I fax a document?
advertisement