D-Link DSL-2750U User Manual
Below you will find brief information for DSL-2750U. This user manual provides comprehensive instructions for setting up and operating the D-Link DSL-2750U router. It covers initial setup, connecting to the internet via various methods (ADSL, Ethernet, 3G/LTE), configuring wireless settings, using the USB port for storage and modems, and managing the device through its web-based interface. The manual also includes troubleshooting tips and safety guidelines.
Advertisement
Advertisement
User Manual
DSL-2750U
Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
April 2018
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Contents
Chapter 1. Introduction..........................................5
Contents and Audience.......................................................5
Conventions.................................................................5
Document Structure..........................................................5
Chapter 2. Overview..............................................6
General Information.........................................................6
Specifications..............................................................7
Product Appearance.........................................................11
Top Panel................................................................11
Back and Bottom Panels...................................................13
Delivery Package...........................................................14
Chapter 3. Installation and Connection..........................15
Before You Begin...........................................................15
Connecting to PC...........................................................17
PC with Ethernet Adapter.................................................17
Obtaining IP Address Automatically in OS Windows XP......................18
Obtaining IP Address Automatically in OS Windows 7.......................21
PC with Wi-Fi Adapter....................................................26
Configuring Wi-Fi Adapter in OS Windows XP...............................27
Configuring Wi-Fi Adapter in OS Windows 7................................28
Connecting to Web-based Interface..........................................30
Web-based Interface Structure..............................................32
Summary Page.............................................................32
Home Page................................................................34
Menu Sections............................................................35
Notifications............................................................36
Chapter 4. Configuring via Web-based Interface..................37
Initial Configuration Wizard...............................................37
Selecting Operation Mode.................................................39
Creating 3G/LTE WAN Connection...........................................41
Selecting Ethernet WAN Port..............................................42
Creating WAN Connection..................................................43
Static IPv4 or IPoA Connection.........................................44
Static IPv6 Connection.................................................45
PPPoE, PPPoA, IPv6 PPPoE, PPPoE Dual Stack Connections.................46
Configuring Wireless Network.............................................47
Configuring LAN Ports for IPTV/VoIP......................................49
Changing Web-based Interface Password....................................51
Connection of Multimedia Devices...........................................53
Statistics.................................................................57
Network Statistics.......................................................57
DHCP.....................................................................58
Routing Table............................................................59
Clients..................................................................60
Multicast Groups.........................................................61
Clients and Session......................................................62
DSL Status...............................................................63
Page 2 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Connections Setup..........................................................64
WAN......................................................................64
Creating Dynamic IPv4, Static IPv4, or IPoA WAN Connection.............66
Creating Dynamic IPv6 or Static IPv6 WAN Connection....................73
Creating PPPoE or PPPoA WAN Connection.................................80
Creating PPPoE IPv6 or PPPoE Dual Stack WAN Connection.................88
Creating Bridge WAN Connection.........................................97
Creating 3G WAN Connection............................................102
Creating LTE WAN Connection...........................................106
LAN.....................................................................110
IPv4..................................................................110
IPv6..................................................................113
WAN Reservation.........................................................115
Wi-Fi.....................................................................117
Basic Settings..........................................................117
Client Management.......................................................126
WPS.....................................................................127
Using WPS Function via Web-based Interface............................129
Using WPS Function without Web-based Interface........................130
WMM.....................................................................131
Additional..............................................................134
MAC Filter..............................................................136
Print Server..............................................................138
USB Storage...............................................................139
Information.............................................................139
USB Users...............................................................140
Samba...................................................................141
FTP.....................................................................143
Filebrowser.............................................................145
DLNA....................................................................146
Torrent Client..........................................................148
USB Modem.................................................................152
Basic Settings..........................................................153
PIN.....................................................................154
Advanced..................................................................156
Interface Grouping......................................................157
WAN Remapping...........................................................159
DNS.....................................................................160
DDNS....................................................................162
Routing.................................................................164
TR-069 Client...........................................................166
Remote Access...........................................................168
UPnP IGD................................................................170
xDSL....................................................................171
IGMP....................................................................172
ALG/Passthrough.........................................................173
Firewall..................................................................175
IP Filter...............................................................175
Virtual Servers.........................................................179
DMZ.....................................................................182
MAC Filter..............................................................183
URL Filter..............................................................185
Page 3 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
System....................................................................186
Configuration...........................................................187
Firmware Update.........................................................189
Local Update..........................................................190
Remote Update.........................................................191
Log.....................................................................192
Ping....................................................................195
Traceroute..............................................................197
Telnet..................................................................199
System Time.............................................................200
Yandex.DNS................................................................202
Settings................................................................202
Devices and Rules.......................................................204
Chapter 5. Operation Guidelines................................206
Safety Rules and Conditions...............................................206
Wireless Installation Considerations......................................207
Chapter 6. Abbreviations and Acronyms..........................208
Page 4 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Introduction
CHAPTER 1. INTRODUCTION
Contents and Audience
This manual describes the router DSL-2750U and explains how to configure and operate it.
This manual is intended for users familiar with basic networking concepts, who create an in-home local area network, and system administrators, who install and configure networks in offices.
Conventions
text
Example
Before You Begin
Description
The body text of the manual.
A reference to a chapter or section of this manual.
“Quick Installation Guide” A reference to a document.
Change
192.168.1.1
A name of a menu, menu item, control (field, checkbox, dropdown list, button, etc.).
Data that you should enter in the specified field.
!
Information An important note.
Document Structure
Chapter 1 describes the purpose and structure of the document.
Chapter 2 gives an overview of the router's hardware and software features and describes its appearance and the package contents.
Chapter 3 explains how to install the wireless router DSL-2750U and configure a PC in order to access its web-based interface.
Chapter 4 describes all pages of the web-based interface in detail.
Chapter 5 includes safety instructions and tips for networking.
Chapter 6 introduces abbreviations and acronyms used in this manual.
Page 5 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Overview
CHAPTER 2. OVERVIEW
General Information
DSL-2750U is a multifunction LTE/3G/ADSL/Ethernet router with Wi-Fi and built-in switch. The router allows accessing the Internet via LTE or 3G GSM network (with a USB modem 1 connected).
In addition, the device allows accessing the Internet via ADSL technology and via Ethernet technology.
The router is equipped with an ADSL port to connect to an ADSL line and 4 Ethernet ports to connect workstations. Due to this feature, DSL-2750U represents a moderate-priced solution for creating wired networks without an additional switch. In addition, any Ethernet port of the device can be used to connect to a private Ethernet line. Also the router has a USB port designed to connect a USB modem, printer, or USB storage.
DSL-2750U can operate as a base station for connecting wireless devices of the standards 802.11b,
802.11g, and 802.11n. The router supports multiple functions for the wireless interface: several security standards (WEP, WPA/WPA2), MAC address filtering, WPS, WMM.
In addition, the device is equipped with a button for switching the Wi-Fi network off/on. If needed, for example, when you leave home, you can easily switch the router’s WLAN by pressing the button, and devices connected to the LAN ports of the router will stay online.
Support of guest Wi-Fi network allows you to create a separate wireless network with individual security settings and maximum rate limitation. Devices connected to the guest network will be able to access the Internet, but will be isolated from the devices and resources of the router's LAN.
The wireless router DSL-2750U includes a built-in firewall. The advanced security functions minimize threats of hacker attacks, prevent unwanted intrusions to your network, and block access to unwanted web sites for users of your LAN.
Built-in Yandex.DNS service protects against malicious and fraudulent web sites and helps to block access to adult content on children's devices.
You can configure and manage the settings of the multifunction wireless router DSL-2750U via the user-friendly web-based interface (the interface is available in several languages).
The fast and easy configuration wizard allows you to specify all needed parameters in several simple steps.
You can simply update the firmware: the router itself finds approved firmware on D-Link update server and notifies when ready to install it.
1 Not included in the delivery package. D-Link does not guarantee compatibility with all USB modems. For the list of supported USB modems, see the Specifications section, page 7.
Page 6 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Overview
Specifications
*
Hardware
Processor
RAM
Flash
Interfaces
LEDs
Buttons
Antenna
MIMO
Power connector
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
RTL8676S
32MB, SDRAM
8MB, SPI
RJ-11 ADSL port
4 10/100BASE-TX LAN ports
USB 2.0 port
POWER
4 LAN LEDs
WLAN
WPS
USB
DSL
INTERNET
ON/OFF button to power on/power off
RESET button to restore factory default settings
WPS button to set up wireless connection
WIRELESS ON/OFF button to enable/disable wireless network
Two external non-detachable omnidirectional antennas (5dBi gain)
2 x 2
Power input connector (DC)
DSL Parameters
ADSL Standards
ATM/PPP Protocols
·
·
·
·
·
·
·
·
·
·
·
·
ADSL: Multi-mode, ANSI T1.413 Issue 2, ITU-T G.992.1 (G.dmt) Annex A, ITU-
T G.992.2 (G.lite) Annex A, ITU-T G.994.1 (G.hs)
ADSL2: ITU-T G.992.3 (G.dmt.bis) Annex A/L/M, ITU-T G.992.4 (G.lite.bis)
Annex A
ADSL2+: ITU-T G.992.5 Annex A/L/M
Bridged and routed Ethernet encapsulation
VC-based or LLC-based multiplexing
ATM Forum UNI3.1/4.0 PVC (up to 8 PVCs)
ATM Adaptation Layer Type 5 (AAL5)
ITU-T I.610 OAM F4/F5 loopback
ATM QoS
PPP over ATM (RFC 2364)
PPP over Ethernet (PPPoE)
Keep-alive for PPP connections
Software
WAN connection types
·
·
·
·
·
·
·
·
·
·
LTE
3G
PPPoA
PPPoE
IPv6 PPPoE
PPPoE Dual Stack
IPoA
Static IPv4 / Dynamic IPv4
Static IPv6 / Dynamic IPv6
Bridge
* The device features are subject to change without notice. For the latest versions of the firmware and relevant documentation, visit www.dlink.ru
.
Page 7 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Software
Network functions
Firewall functions
VPN
QoS
USB interface functions
Management
Overview
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
DHCP server/relay
Stateful/Stateless mode for IPv6 address assignment, IPv6 prefix delegation
DNS relay
Dynamic DNS
Static IP routing
Static IPv6 routing
IGMP Proxy
IGMP snooping
RIP
Support of UPnP IGD
Support of VLAN
WAN ping respond
Support of SIP ALG
Support of RTSP
WAN reservation
Network Address Translation (NAT)
Stateful Packet Inspection (SPI)
IP filter
IPv6 filter
MAC filter
URL filter
DMZ
Prevention of ARP and DDoS attacks
Virtual servers
Built-in Yandex.DNS web content filtering service
IPsec/PPTP/L2TP/PPPoE pass-through
Interface grouping
VLAN priority (802.1p)
USB modem
Auto connection to available type of supported network (4G/3G/2G)
Auto configuration of connection upon plugging in USB modem
Enabling/disabling PIN code check, changing PIN code 2
USB storage
File browser
Print server
Access to storage via accounts
Built-in Samba/FTP/DLNA server
Built-in Transmission torrent client; uploading/downloading files from/to USB storage
Local and remote access to settings through TELNET/WEB (HTTP/HTTPS)
Multilingual web-based interface for configuration and management
Firmware update via web-based interface
Automatic notification on new firmware version
Saving/restoring configuration to/from file
Support of logging to remote host/connected USB storage
Automatic synchronization of system time with NTP server and manual time/date setup
Ping utility
Traceroute utility
TR-069 client
2 For some models of USB modems.
Page 8 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Overview
Wireless Module Parameters
Standards
Frequency range
Wireless connection security
Advanced functions
Wireless connection rate
Transmitter output power
The maximum value of the transmitter output power depends upon the radio frequency regulations applied in your country
Receiver sensitivity
Modulation schemes
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
IEEE 802.11b/g/n
2400 ~ 2483.5MHz
WEP
WPA/WPA2 (Personal/Enterprise)
МАС filter
WPS (PBC/PIN)
WMM (Wi-Fi QoS)
Information on connected Wi-Fi clients
Advanced settings
Guest Wi-Fi / support of MBSSID
Limitation of wireless network rate
Periodic scan of channels, automatic switch to least loaded channel
Autonegotiation of channel bandwidth in accordance with environment conditions (20/40 Coexistence)
IEEE 802.11b: 1, 2, 5.5, and 11Mbps
IEEE 802.11g: 6, 9, 12, 18, 24, 36, 48, and 54Mbps
IEEE 802.11n: from 6.5 to 300Mbps (from MCS0 to MCS15)
802.11b (typical at room temperature 25 °C)
15dBm
802.11g (typical at room temperature 25 °C)
13.5 ~ 15dBm
802.11n (typical at room temperature 25 °C)
13.5 ~ 15dBm
802.11b (typical at room temperature 25 °C)
-84dBm
802.11g (typical at room temperature 25 °C)
-72dBm
802.11n (typical at room temperature 25 °C)
HT20
-70dBm
HT40
-67dBm
802.11b: CCK (11, 5.5Mbps), DQPSK (2Mbps), DBPSK (1Mbps), DSSS
802.11g: PSK/CCK, DBPSK, DQPSK, OFDM, BPSK, QPSK, 16QAM, 64QAM
802.11n: PSK/CCK, DBPSK, DQPSK, OFDM, etc.
Physical Parameters
Dimensions (L x W x H)
Weight
Operating Environment
Power
Temperature
Humidity
·
·
174 x 119 x 32 mm (6.6 x 4.7 x 1.3 in)
197 g (0.43 lb)
·
·
·
·
Output: 12V DC, 1A
Operating: from 0 to 40 °C
Storage: from -20 to 70 °C
From 5% to 95% (non-condensing)
Page 9 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Supported USB modems 3
GSM
LTE
Smartphones in USB tethering mode
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
Alcatel X500
D-Link DWM-152C1
D-Link DWM-156A6
D-Link DWM-156A7
D-Link DWM 156A8
D-Link DWM-156C1
D-Link DWM-157B1
D-Link DWM-157B1 (Velcom)
D-Link DWM-158D1
D-Link DWR-710
Huawei E150
Huawei E1550
Huawei E156G
Huawei E160G
Huawei E169G
Huawei E171
Huawei E173 (Megafon)
Huawei E220
Huawei E3131 (MTS 420S)
Huawei E352 (Megafon)
Prolink PHS600
Prolink PHS901
ZTE MF112
ZTE MF192
ZTE MF626
ZTE MF627
ZTE MF652
ZTE MF667
ZTE MF668
ZTE MF752
Huawei E3131
Huawei E3272
Huawei E3351
Huawei E3372
Huawei E367
Huawei E392
Megafon M100-1
Megafon M100-2
Megafon M100-3
Megafon M100-4
Megafon M150-1
Megafon M150-2
Quanta 1K6E (Beeline 1K6E)
MTS 824F
MTS 827F
Yota LU-150
Yota WLTUBA-107
ZTE MF823
ZTE MF827
Some models of Android smartphones
Overview
3 The manufacturer does not guarantee proper operation of the router with every modification of the firmware of USB modems.
Page 10 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Product Appearance
Top Panel
Overview
LED
POWER
Mode
Solid green
Figure 1. Top panel view.
Description
The router is powered on.
Blinking green
Solid red
No light
The firmware is being updated.
The router is being loaded.
The router is powered off.
Page 11 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
LED
LAN 1-4
WLAN
WPS
USB
DSL
INTERNET
Overview
No light
Solid green
Blinking green
No light
Solid green
No light
Mode
Solid green
Solid green
Description
A device is connected to the port of the router (for the LAN port configured as the WAN port: the router is connected to an Ethernet line).
Blinking green
No light
Solid green
The relevant LAN port is active (upstream or downstream traffic).
The cable is not connected to the relevant port.
A client has connected to the WLAN.
Slow blinking green The router's WLAN is on.
Fast blinking green
The WLAN interface is active (upstream or downstream traffic).
No light The router's WLAN is off.
Blinking green
No light
Attempting to add a wireless device via the WPS function.
The WPS function is not in use.
A USB device is connected to the router's USB port.
No USB device.
DSL has been synchronized.
Detecting a carrier signal and synchronizing DSL.
No carrier signal.
A WAN connection is established.
The router is in the bridge mode or no WAN connection is created.
Page 12 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Back and Bottom Panels
Overview
Port
DSL
LAN 1-4
Figure 2. Back panel view.
Description
A DSL port to connect the router to the telephone line.
4 Ethernet ports to connect Ethernet devices. One port can be used to connect to a private Ethernet line.
A port for connecting a USB device (modem, storage, printer).
USB
WPS
A button to set up a wireless connection (the WPS function).
To use the WPS function: with the device turned on, push the button and immediately release it. The WPS LED should start blinking.
WIRELESS
ON/OFF
ON/OFF
A button to enable/disable the router's wireless network.
A button to turn the router on/off.
12VDC IN Power connector.
The RESET button located on the bottom panel of the router is designed to restore the factory default settings. To restore the factory defaults, push the button (with the device turned on), hold it for 10 seconds, and then release the button.
Page 13 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Overview
The device is also equipped with external non-detachable Wi-Fi antennas.
Delivery Package
The following should be included:
• Router DSL-2750U
• Power adapter DC 12V/1A
• RJ-11 telephone cable
• Ethernet cable
• Splitter
• “ Quick Installation Guide ” (brochure).
The “ User Manual ” and “ Quick Installation Guide ” documents are available on D-Link website
(see www.dlink.ru
).
!
Using a power supply with a different voltage rating than the one included will cause damage and void the warranty for this product.
Page 14 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Installation and Connection
CHAPTER 3. INSTALLATION AND CONNECTION
Before You Begin
Please, read this manual prior to installing the device. Make sure that you have all the necessary information and equipment.
Operating System
Configuration of the LTE/3G/ADSL/Ethernet router DSL-2750U with Wi-Fi and built-in switch
(hereinafter referred to as “the router”) is performed via the built-in web-based interface. The webbased interface is available from any operating system that supports a web browser.
Web Browser
The following web browsers are recommended:
• Apple Safari 8 and later
• Google Chrome 48 and later
• Microsoft Internet Explorer 10 and later
• Microsoft Edge 20.10240 and later
• Mozilla Firefox 44 and later
• Opera 35 and later.
For successful operation, JavaScript should be enabled on the web browser. Make sure that
JavaScript has not been disabled by other software (such as virus protection or web user security packages) running on your computer.
Wired or Wireless NIC (Ethernet or Wi-Fi Adapter)
Any computer that uses the router should be equipped with an Ethernet or Wi-Fi adapter (NIC). If your computer is not equipped with such a device, install an Ethernet or Wi-Fi adapter prior to using the router.
Wireless Connection
Wireless workstations from your network should be equipped with a wireless 802.11b, g, or n NIC
(Wi-Fi adapter). In addition, you should specify the values of SSID, channel number and security settings defined in the web-based interface of the router for all these wireless workstations.
Page 15 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Installation and Connection
USB Modem
To connect to an LTE or 3G network, you should use a USB modem. Connect it to the USB port of the router, then access the web-based interface of the router, and you will be able to configure a connection to the Internet 4 .
!
Your USB modem should be equipped with an active SIM card of your operator.
Some operators require subscribers to activate their USB modems prior to using them.
Please, refer to connection guidelines provided by your operator when concluding the agreement or placed on its website.
For some models of USB modems, it is required to disable the PIN code check on the SIM card prior to connecting the USB modem to the router.
4 Contact your operator to get information on the service coverage and fees.
Page 16 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Installation and Connection
Connecting to PC
PC with Ethernet Adapter
1. Make sure that your PC is powered off.
2. Connect an Ethernet cable between any of four Ethernet ports located on the back panel of the router and the Ethernet port of your PC.
3.
To connect via USB modem: connect your USB modem to the USB port 5 located on the back panel of the router.
!
In some cases you will need to reboot the router after connection of the USB modem.
4.
To connect the router to a DSL line: connect a phone cable between the DSL port of the router and the ADSL OUT port of the splitter. Connect your phone to the PHONE port of the splitter. Then connect another phone cable between a phone jack and the ADSL IN port of the splitter.
5.
To connect the router to an Ethernet line: run the Initial Configuration Wizard and select the router's LAN port that will be used as the WAN port. Then connect the Ethernet cable between the selected Ethernet port located on the back panel of the router and the Ethernet line.
6. Connect the power cord to the power connector port on the back panel of the router, then plug the power adapter into an electrical outlet or power strip.
7. Turn on the router by pressing the ON/OFF button on its back panel.
8. Turn on your PC and wait until your operating system is completely loaded.
5 It is recommended to use a USB extension cable to connect a USB modem to the router.
Page 17 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Installation and Connection
Obtaining IP Address Automatically in OS Windows XP
1. Click the Start button and proceed to the Control Panel > Network and Internet
Connections > Network Connections window.
2. In the Network Connections window, right-click the relevant Local Area Connection icon and select the Properties line in the menu displayed.
Figure 3. The Network Connections window.
Page 18 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Installation and Connection
3. In the Local Area Connection Properties window, on the General tab, select the
Internet Protocol (TCP/IP) line. Click the Properties button.
Figure 4. The Local Area Connection Properties window.
Page 19 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Installation and Connection
4. Select the Obtain an IP address automatically and Obtain DNS server address automatically radio buttons. Click the OK button.
Figure 5. The Internet Protocol (TCP/IP) Properties window.
5. Click the ОК button in the connection properties window.
Now your computer is configured to obtain an IP address automatically.
Page 20 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Installation and Connection
Obtaining IP Address Automatically in OS Windows 7
1. Click the Start button and proceed to the Control Panel window.
2. Select the Network and Sharing Center section. (If the Control Panel has the category view (the Category value is selected from the View by drop-down list in the top right corner of the window), choose the View network status and tasks line under the
Network and Internet section.)
Figure 6. The Control Panel window.
Page 21 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Installation and Connection
3. In the menu located on the left part of the window, select the Change adapter settings line.
Figure 7. The Network and Sharing Center window.
Page 22 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Installation and Connection
4. In the opened window, right-click the relevant Local Area Connection icon and select the Properties line in the menu displayed.
Figure 8. The Network Connections window.
Page 23 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Installation and Connection
5. In the Local Area Connection Properties window, on the Networking tab, select the
Internet Protocol Version 4 (TCP/IPv4) line. Click the Properties button.
Figure 9. The Local Area Connection Properties window.
Page 24 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Installation and Connection
6. Select the Obtain an IP address automatically and Obtain DNS server address automatically radio buttons. Click the OK button.
Figure 10. The Internet Protocol Version 4 (TCP/IPv4) Properties window.
7. Click the OK button in the connection properties window.
Now your computer is configured to obtain an IP address automatically.
Page 25 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Installation and Connection
PC with Wi-Fi Adapter
1.
To connect via USB modem: connect your USB modem to the USB port 6 located on the back panel of the router.
!
In some cases you will need to reboot the router after connection of the USB modem.
2.
To connect the router to a DSL line: connect a phone cable between the DSL port of the router and the ADSL OUT port of the splitter. Connect your phone to the PHONE port of the splitter. Then connect another phone cable between a phone jack and the ADSL IN port of the splitter.
3.
To connect the router to an Ethernet line: run the Initial Configuration Wizard and select the router's LAN port that will be used as the WAN port. Then connect the Ethernet cable between the selected Ethernet port located on the back panel of the router and the Ethernet line.
4. Connect the power cord to the power connector port on the back panel of the router, then plug the power adapter into an electrical outlet or power strip.
5. Turn on the router by pressing the ON/OFF button on its back panel.
6. Turn on your PC and wait until your operating system is completely loaded.
7. Turn on your Wi-Fi adapter. As a rule, modern notebooks with built-in wireless NICs are equipped with a button or switch that turns on/off the wireless adapter (refer to your PC documents). If your PC is equipped with a pluggable wireless NIC, install the software provided with your Wi-Fi adapter.
6 It is recommended to use a USB extension cable to connect a USB modem to the router.
Page 26 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Installation and Connection
Configuring Wi-Fi Adapter in OS Windows XP
1. Click the Start button and proceed to the Control Panel > Network and Internet
Connections > Network Connections window.
2. Select the icon of the wireless network connection and make sure that your Wi-Fi adapter is on.
Figure 11. The Network Connections window.
3. Search for available wireless networks.
4. In the opened Wireless Network Connection window, select the wireless network DSL-
2750U and click the Connect button.
5. In the opened window, enter the network key (see WPS PIN on the barcode label on the bottom panel of the device) in the Network key and Confirm network key fields and click the Connect button.
After that the Wireless Network Connection Status window appears.
!
If you perform initial configuration of the router via Wi-Fi connection, note that immediately after changing the wireless default settings of the router you will need to reconfigure the wireless connection using the newly specified settings.
Page 27 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Installation and Connection
Configuring Wi-Fi Adapter in OS Windows 7
1. Click the Start button and proceed to the Control Panel window.
2. Select the Network and Sharing Center section. (If the Control Panel has the category view (the Category value is selected from the View by drop-down list in the top right corner of the window), choose the View network status and tasks line under the
Network and Internet section.)
Figure 12. The Control Panel window.
3. In the menu located on the left part of the window, select the Change adapter settings line.
4. In the opened window, select the icon of the wireless network connection and make sure that your Wi-Fi adapter is on.
5. To open the list of available wireless networks, select the icon of the wireless network connection and click the Connect To button or left-click the network icon in the notification area located on the right side of the taskbar.
Figure 13. The notification area of the taskbar.
Page 28 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Installation and Connection
6. In the opened window, in the list of available wireless networks, select the wireless network
DSL-2750U and click the Connect button.
!
Figure 14. The list of available networks.
7. In the opened window, enter the network key (see WPS PIN on the barcode label on the bottom panel of the device) in the Security key field and click the OK button.
8. Wait for about 20-30 seconds. After the connection is established, the network icon will be displayed as the signal level scale.
If you perform initial configuration of the router via Wi-Fi connection, note that immediately after changing the wireless default settings of the router you will need to reconfigure the wireless connection using the newly specified settings.
Page 29 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Installation and Connection
Connecting to Web-based Interface
When you have configured your computer, you can access the web-based interface and configure needed parameters (create a WAN connection, change the parameters of the wireless network, specify the settings of the firewall, etc.)
Start a web browser (see the Before You Begin section, page 15). In the address bar of the web browser, enter the IP address of the router (by default, 192.168.1.1
) or its domain name (by default, dlinkrouter.local
) with a dot at the end. Press the Enter key.
Figure 15. Connecting to the web-based interface of the DSL-2750U device.
!
If the error “ The page cannot be displayed ” (or “ Unable to display the page ”/“ Could not connect to remote server ”) occurs upon connecting to the web-based interface of the router, make sure that you have properly connected the router to your computer.
If the device has not been configured previously or the default settings have been restored, after access to the web-based interface the Initial Configuration Wizard opens (see the Initial
Configuration Wizard section, page 37).
Figure 16. The page for running the Initial Configuration Wizard.
Page 30 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Installation and Connection
If you configured the device previously, after access to the web-based interface the login page opens. Enter the username ( admin ) in the Username field and the password you specified in the
Password field, then click the LOGIN button.
Figure 17. The login page.
Page 31 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Web-based Interface Structure
Summary Page
On the Summary page, detailed information on the device state is displayed.
Installation and Connection
Figure 18. The summary page.
Page 32 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Installation and Connection
The Device Information section displays the model and hardware version of the router, the firmware version, and other data.
To contact the technical support group (to send an e-mail), left-click the support e-mail address.
After clicking the line, the e-mail client window for sending a new letter to the specified address opens.
The Wi-Fi 2.4 GHz section displays data on the state of the device's wireless network, its name and the authentication type, and availability of an additional wireless network.
In the WAN section, data on the type and status of the existing WAN connection are displayed.
In the LAN section, the IPv4 and IPv6 address of the router and the number of wired and wireless clients of the device are displayed.
The LAN Ports section displays the state of the device's LAN ports.
In the DSL Status section, data on the DSL connection state is displayed.
The USB Devices section displays the device connected to the USB port of the router.
The Yandex.DNS
section displays the Yandex.DNS service state and operation mode. To enable the Yandex.DNS service, move the Enable switch to the right. If needed, change the operation mode of the service.
Page 33 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Installation and Connection
Home Page
The Home page displays links to the most frequently used pages with device's settings.
Figure 19. The Home page.
Other settings of the router are available in the menu in the left part of the page.
Page 34 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Installation and Connection
Menu Sections
To configure the router use the menu in the left part of the page.
In the Initial Configuration section you can run the Initial Configuration Wizard. The Wizard allows you to configure the router for operation in the needed mode and specify all parameters necessary for getting started (for the description of the Wizard, see the Initial Configuration
Wizard section, page 37).
The pages of the Statistics section display data on the current state of the router (for the description of the pages, see the Statistics section, page 57).
The pages of the Connections Setup section are designed for configuring basic parameters of the LAN interface of the router and creating a connection to the Internet (for the description of the pages, see the Connections Setup section, page 64).
The pages of the Wi-Fi section are designed for specifying all needed settings of the router's wireless network (for the description of the pages, see the Wi-Fi section, page 117).
The Print Server section is designed for configuring the router as a print server (see the Print
Server section, page 138).
The pages of the USB Storage section are designed for operating the connected USB storage (for the description of the pages, see the USB Storage section, page 139).
The pages of the USB Modem section are designed for operating the connected 3G or LTE USB modem (for the description of the pages, see the USB Modem section, page 152).
The pages of the Advanced section are designed for configuring additional parameters of the router (for the description of the pages, see the Advanced section, page 156).
The pages of the Firewall section are designed for configuring the firewall of the router (for the description of the pages, see the Firewall section, page 175).
The pages of the System section provide functions for managing the internal system of the router
(for the description of the pages, see the System section, page 186).
The pages of the Yandex.DNS
section are designed for configuring the Yandex.DNS web content filtering service (for the description of the pages, see the Yandex.DNS
section, page 202).
To exit the web-based interface, click the Logout line of the menu.
Page 35 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Installation and Connection
Notifications
The router's web-based interface displays notifications in the top right part of the page.
Figure 20. The web-based interface notifications.
Click the icon displaying the number of notifications to view the complete list and click the relevant button.
Page 36 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
CHAPTER 4. CONFIGURING VIA WEB-BASED
INTERFACE
Initial Configuration Wizard
To start the Initial Configuration Wizard, go to the Initial Configuration section. On the opened page, click the OK button and wait until the factory default settings are restored.
Click the START button.
Figure 21. Restoring the default settings in the Wizard.
Figure 22. Starting the Wizard.
On the opened page, click YES in order to leave the current language of the web-based interface or click NO to select another language.
Figure 23. Selecting a language.
Page 37 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
You can finish the wizard earlier and go to the menu of the web-based interface. To do this, click the
ADVANCED SETTINGS button. On the opened page, change the default settings: specify the administrator password in the Admin password field and the name of the wireless network in the
Network name (SSID) field. Then click the APPLY button.
Figure 24. Changing the default settings.
To continue the configuration of the router via the Wizard, click the CONTINUE button.
Page 38 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Selecting Operation Mode
In order to connect your device to an ADSL line, on the Device mode page, from the
Connection method list, select the ADSL value. In this mode you can configure a WAN connection, set your own settings for the wireless network, configure LAN ports to connect an STB or VoIP phone, and set your own password for access to the web-based interface of the device.
Figure 25. Selecting an operation mode. The ADSL connection method.
In order to connect your device to an Ethernet line, on the Device mode page, from the
Connection method list, select the Ethernet (LAN) value. In this mode you can configure a
LAN port as a WAN port, configure a WAN connection, set your own settings for the wireless network, configure LAN ports to connect an STB or VoIP phone, and set your own password for access to the web-based interface of the device.
Figure 26. Selecting an operation mode. The Ethernet connection method.
Page 39 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
In order to connect your device to the network of a 3G or LTE operator, on the Device mode page, from the Connection method list, select the 3G/LTE modem value. In this mode you can configure a 3G/LTE WAN connection, set your own settings for the wireless network, and set your own password for access to the web-based interface of the device.
Figure 27. Selecting an operation mode. The 3G/LTE modem mode.
When the operation mode is selected, click the NEXT button.
Page 40 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Creating 3G/LTE WAN Connection
This configuration step is available for the 3G/LTE modem mode.
1. If the PIN code check is enabled for the SIM card inserted into your USB modem, enter the
PIN code in the PIN field and click the APPLY button.
Figure 28. The page for entering the PIN code.
2. Please wait while the router automatically creates a WAN connection for your mobile operator.
Figure 29. The page for creating 3G/LTE connection .
3.
Click the NEXT button to continue or click the BACK button to return to the previous page.
If the router failed to create a WAN connection automatically, click the CONFIGURE
MANUALLY button. On the Internet connection type page, configure all needed settings and click the NEXT button.
Page 41 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Selecting Ethernet WAN Port
This configuration step is available for the Ethernet (LAN) connection method.
1. On the Device connection page, select a LAN port that will be used as the WAN port.
2. Click the NEXT button.
Page 42 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Creating WAN Connection
!
You should configure your WAN connection in accordance with data provided by your
Internet service provider (ISP). Make sure that you have obtained all necessary information prior to configuring your connection. Otherwise contact your ISP.
1. On the Internet connection type page, from the Connection type list, select the connection type used by your ISP and fill in the fields displayed on the page.
2. Specify the settings necessary for the connection of the selected type.
3.
For the Ethernet (LAN) connection method : If your ISP uses MAC address binding, select the Clone MAC address of your device checkbox.
4.
For the Ethernet (LAN) connection method : If the Internet access is provided via a VLAN channel, select the Use VLAN checkbox and fill in the VLAN ID field.
5.
For the ADSL connection method : Specify the VPI and VCI values in the relevant fields.
6. Click the NEXT button to continue or click the BACK button to return to the previous page.
Page 43 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Static IPv4 or IPoA Connection
Configuring via Web-based Interface
Figure 30. The page for configuring Static IPv4 WAN connection.
The IPoA connection type is available for the ADSL connection method only.
Fill in the following fields: IP address , Netmask , Gateway IP address , and DNS IP address .
Page 44 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Static IPv6 Connection
Configuring via Web-based Interface
Figure 31. The page for configuring Static IPv6 WAN connection.
Fill in the following fields: IP address , Prefix and Gateway IP address .
Page 45 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
PPPoE, PPPoA, IPv6 PPPoE, PPPoE Dual Stack Connections
Figure 32. The page for configuring PPPoE WAN connection.
The PPPoA connection type is available for the ADSL connection method only.
In the Username field enter the login and in the Password field enter the password provided by your ISP. Click the Show icon ( ) to display the entered password. If authorization is not required, select the Without authorization checkbox.
Page 46 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Configuring Wireless Network
1. On the Wireless Network 2.4 GHz page, in the Network name field, specify your own name for the wireless network or leave the value suggested by the router.
2. In the Password field, specify your own password for access to the wireless network or leave the value suggested by the router (WPS PIN of the device, see the barcode label).
3. You can restore the parameters of the wireless network specified before resetting to factory defaults. To do this, click the RESTORE button.
Figure 33. The page for configuring the wireless network.
Page 47 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
4. If you want to create an additional wireless network isolated from your LAN, select the
Enable guest network checkbox.
Figure 34. The page for configuring the wireless network.
5. In the Network name field, specify your own name for the guest wireless network or leave the value suggested by the router.
6. If you want to create a password for access to the guest wireless network, deselect the Open network checkbox and fill in the Password field.
7. If you want to limit the bandwidth of the guest wireless network, select the Enable shaping checkbox and fill in the Shaping field.
8. Click the NEXT button to continue or click the BACK button to specify other settings.
Page 48 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Configuring LAN Ports for IPTV/VoIP
1. On the IPTV page, select the Is an STB connected to the device checkbox.
Figure 35. The page for selecting a LAN port to connect an IPTV set-top box.
2. Select a free LAN port for connecting your set-top box.
3.
For the Ethernet (LAN) connection method : If the IPTV service is provided via a VLAN channel, select the Use VLAN ID checkbox and fill in the VLAN ID field.
4.
For the ADSL connection method : Specify the VPI and VCI values in the relevant fields.
5. Click the NEXT button to continue or click the BACK button to specify other settings.
Page 49 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
6. On the VoIP page, select the Is an IP phone connected to the device checkbox.
Figure 36. The page for selecting a LAN port to connect an VoIP phone.
7. Select a free LAN port for connecting your IP phone.
8.
For the Ethernet (LAN) connection method : If the VoIP service is provided via a VLAN channel, select the Use VLAN ID checkbox and fill in the VLAN ID field.
9.
For the ADSL connection method : Specify the VPI and VCI values in the relevant fields.
10. Click the NEXT button to continue or click the BACK button to specify other settings.
Page 50 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Changing Web-based Interface Password
On this page, you should change the default administrator password. You may set any password except admin . Use digits, Latin letters (uppercase and/or lowercase), and other characters available in the US keyboard layout.
7
Figure 37. The page for changing the web-based interface password.
!
Remember or write down the new password for the administrator account. In case of losing the new password, you can access the settings of the router only after restoring the factory default settings via the hardware RESET button. This procedure wipes out all settings that you have configured for your router.
Click the NEXT button to continue or click the BACK button to return to the previous page.
On the next page, check all specified settings.
Also you can save a text file with parameters set by the Wizard to your PC. To do this, click the
SAVE CONFIGURATION FILE button and follow the dialog box appeared.
To finish the Wizard, click the APPLY button. The router will apply settings and reboot. Click the
BACK button to specify other settings.
7 0-9, A-Z, a-z, space, !"#$%&'()*+,-./:;<=>?@[\]^_`{|}~.
Page 51 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
If the Wizard has configured a WAN connection, after clicking the APPLY button, the page for checking the Internet availability opens.
Figure 38. Checking the Internet availability.
If the router has been successfully connected to the Internet, click the FINISH button.
If problems appeared when connecting to the Internet, click the CHECK AGAIN button to recheck the state of the WAN connection.
If problems of connection have not been solved, contact the technical support of your ISP (as a rule, the technical support phone is provided with the agreement) or the D-Link technical support (the phone number will be displayed on the page after several attempts of checking the connection).
To specify other settings, click the ADVANCED SETTINGS button. After clicking the
ADVANCED SETTINGS button, the Summary page opens (see the Summary Page section, page 32).
Page 52 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Connection of Multimedia Devices
The Multimedia Devices Connection Wizard helps to configure LAN ports or available wireless interfaces of the router for connecting additional devices, for example, an IPTV set-top box or IP phone. Contact your ISP to clarify if you need to configure DSL-2750U in order to use these devices.
To start the Wizard, on the Home page, select the Connection of Multimedia Devices section.
Figure 39. The Multimedia Devices Connection Wizard.
Page 53 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
In the WAN section, click the Add icon ( ).
Configuring via Web-based Interface
Figure 40. Adding a connection.
You can specify the following parameters:
Parameter
Name
Interface
VPI
VCI
Encapsulation
QoS class
Description
A name for the connection for easier identification (you can specify any name).
Select the value corresponding to the LAN port specified as the
WAN port for connection to an Ethernet line or the DSL value for connection to an ADSL line.
For the DSL value only.
Virtual Path Identifier. The valid range is from 0 to 255.
For the DSL value only.
Virtual Circuit Identifier. The valid range is from 32 to 65535.
For the DSL value only.
Select LLC or VCMUX from the drop-down list.
For the DSL value only.
A class of traffic for this connection.
UBR
( Unspecified Bit Rate ): The UBR service is used for applications that allow various delays and losses of packets. It is appropriate to use the UBR service for text/data/image transfer applications, as well as messaging, distribution, retrieval, and remote terminal applications.
UBR with PCR
Page 54 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Parameter Description
( Unspecified Bit Rate with Peak Cell Rate ): The UBR service is used for applications that allow various delays and losses of packets. The
Peak Cell Rate is a determining factor in how often cells are sent in an effort to minimize lag or jitter caused by traffic inconsistencies.
When you select this value from the drop-down list, the Peak cell rate field is displayed. Specify a required value (in cells per second).
CBR
( Constant Bit Rate ): This service is used for applications that require a constant data rate. It is mostly used for transferring uncompressed audio and video, e.g. videoconferencing, interactive audio
(telephony), audio/video distribution (television, distance education, e-shops), and retrieval (video-on demand, audio libraries). When you select this value from the drop-down list, the Peak cell rate field is displayed. Specify a required value (in cells per second).
Non Realtime VBR
( Non-Real-time Variable Bit Rate ): This service can be used for transferring data that have critical response-time requirements, e.g.
air ticket booking, bank transactions, and process monitoring. When you select this value from the drop-down list, the Peak cell rate ,
Sustainable cell rate , and Maximum burst size fields are displayed. Specify required values.
Realtime VBR
( Real-time Variable Bit Rate ): This service is used for delay-sensitive applications such as real time video. The Rt-VBR provides higher network flexibility than the CBR service. When you select this value from the drop-down list, the Peak cell rate , Sustainable cell rate , and Maximum burst size fields are displayed. Specify required values.
VLAN ID
If the service used by your additional equipment is provided via a
VLAN channel with a tag (VLAN ID), specify the needed value.
Allowed
Move the switch to the right to enable the connection.
Move the switch to the left to disable the connection.
Click the SAVE button.
Then in the LAN section, from the Bridged with drop-down list of the element corresponding to the LAN port or wireless interface to which the additional device is connected, select the created connection. Click the APPLY button.
Page 55 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
!
The selected port or wireless interface cannot use the default connection to access the
Internet.
To deselect the port or wireless interface, select the No value from the Bridged with drop-down list of the element corresponding to the needed LAN port or interface. Then in the WAN section, select the connection which will not be used any longer and click the REMOVE button. Then click the APPLY button.
Page 56 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Statistics
The pages of this section display data on the current state of the router:
• network statistics
• IP addresses leased by the DHCP server
• the routing table
• data on devices connected to the router's network and its web-based interface
• addresses of active multicast groups
• active sessions
• DSL connection status .
Network Statistics
On the Statistics / Network Statistics page, you can view statistics for all connections existing in the system (WAN connections, LAN, WLAN). For each connection the following data are displayed: name and state (when the connection is on, its name is highlighted in green, when the connection is off, its name is highlighted in red), IP address and subnet mask, gateway (if the connection is established), MAC address, and volume of data received and transmitted (with increase of the volume the units of measurement are changed automatically: byte, Kbyte, Mbyte,
Gbyte).
Figure 41. The Statistics / Network Statistics page.
To view data on a connection, click the line corresponding to this connection.
Page 57 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
DHCP
The Statistics / DHCP page displays the information on computers that have been identified by hostnames and MAC addresses and have got IP addresses from the DHCP server of the device, as well as the IP address expiration periods (the lease time).
Figure 42. The Statistics / DHCP page.
Page 58 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Routing Table
The Statistics / Routing Table page displays the information on routes. The table contains destination IP addresses, gateways, subnet masks, and other data.
Figure 43. The Statistics / Routing Table page.
Page 59 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Clients
On the Statistics / Clients page, you can view the list of devices connected to the local network of the router.
Figure 44. The Statistics / Clients page.
For each device the following data are displayed: the IP address, the MAC address, and the network interface to which the device is connected.
Page 60 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Multicast Groups
The Statistics / Multicast Groups page displays addresses of active multicast groups (including
IPTV channels and groups for transferring service information) to which the device is subscribed, and the interface through which the device is subscribed.
Figure 45. The Statistics / Multicast Groups page.
Page 61 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Clients and Session
On the Statistics / Clients and Session page, you can view information on current sessions in the router's network. For each session the following data are displayed: the protocol for network packet transmission, the source IP address and port, and the destination IP address and port.
Figure 46. The Statistics / Clients and Session page.
To view the latest data on current sessions in the router's network, click the REFRESH button.
Page 62 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
DSL Status
The information shown on the Statistics / DSL Status page can be used for troubleshooting and diagnosing connection problems.
In the DSL status and Line sections you can view data on your DSL line: the line state, data transfer rate (downstream/upstream traffic), physical parameters of the line (SNR, output power).
The Framing section displays information on transmitted DSL frames.
Figure 47. The Statistics / DSL Status page.
Page 63 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Connections Setup
In this menu you can configure basic parameters of the router's local area network and configure connection to the Internet (a WAN connection).
WAN
On the Connections Setup / WAN page, you can create and edit connections used by the router.
By default, an ADSL connection of the Dynamic IP type is configured in the system. It is assigned to the DSL port of the router.
!
!
Please reboot the router after creating, editing, or removing an ADSL WAN connection.
Prior to creating an Ethernet WAN connection, specify a LAN port that will be used as the
WAN port (see the WAN Remapping section, page
Figure 48. The Connections Setup / WAN page. The simplified mode.
To edit an existing connection, click the EDIT button. On the opened page, on the Basic tab, the mandatory settings of this WAN connection will be displayed. To view all available settings of the
WAN connection, go to the All Settings tab. Change the needed parameters and click the APPLY button.
To disconnect a connection and establish it again, click the RECONNECT button.
To remove an existing connection and create a new one, click the CHANGE CONFIGURATION button. Upon that the connection creation page opens.
To create several WAN connections, go to the advanced mode. To do this, click the ADVANCED
MODE button.
!
When connections of some types are created, the Connections Setup / WAN page is automatically displayed in the advanced mode.
Page 64 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Figure 49. The Connections Setup / WAN page. The advanced mode.
To create a new connection, click the ADD button in the Connections List section. Upon that the connection creation page opens.
To edit an existing connection, in the Connections List section, left-click the relevant line in the table. On the opened page, on the Basic tab, mandatory settings of this WAN connection will be displayed. To view all available settings of the WAN connection, go to the All Settings tab.
Change the needed parameters and click the APPLY button.
To disconnect a connection and establish it again, select the checkbox located to the left of the relevant line in the table and click the RECONNECT button.
To remove a connection, in the Connections List section, select the checkbox located to the left of the relevant line in the table and click the DELETE button. Also you can remove a connection on the editing page.
To allow multicast traffic (e.g. streaming video) for a connection, click the IGMP link (for the description of the page, see the IGMP section, page 172).
To use one of existing WAN connections as the default IPv4 or IPv6 connection, in the Default gateway section, select the choice of the radio button which corresponds to this connection.
To return to the simplified mode, click the SIMPLIFIED MODE button (the button is unavailable, if several WAN connections are created).
Page 65 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Creating Dynamic IPv4, Static IPv4, or IPoA WAN Connection
On the connection creation page, go to the All Settings tab. Then select the relevant value from the Connection Type drop-down list and specify the needed values.
Figure 50. The page for creating a new Static IPv4 connection. Selecting a connection type.
Parameter Description
Interface
For the Dynamic IPv4 and Static IPv4 types only.
A physical interface to which the new connection will be assigned.
In order to create an Ethernet WAN connection, select the value corresponding to the LAN port specified as the WAN port.
In order to create an ADSL WAN connection, select the value corresponding to the existing interface or the Add new ATM PVC value for creating a new interface at the physical layer.
Enable connection
Connection name
Move the switch to the right to enable the connection.
Move the switch to the left to disable the connection.
Available for the advanced mode only.
A name for the connection for easier identification.
Page 66 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
The Ethernet section is displayed for Ethernet WAN connections.
Configuring via Web-based Interface
Figure 51. The page for creating a new Static IPv4 connection. The Ethernet section.
Parameter Description
MAC address
Ethernet
A MAC address assigned to the interface. This parameter is mandatory if your ISP uses MAC address binding. In the field, enter the MAC address registered by your ISP upon concluding the agreement.
To set the MAC address of the network interface card (of the computer that is being used to configure the router at the moment) as the MAC address of the WAN interface, move the Clone MAC address of your NIC switch to the right. When the switch is moved to the right, the field is unavailable for editing.
To set the router's MAC address, click the RESTORE DEFAULT
MAC ADDRESS button (the button is available when the switch is moved to the right).
Page 67 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
The ATM section is displayed for ADSL WAN connections.
Configuring via Web-based Interface
Figure 52. The page for creating a new Static IPv4 connection. The ATM section.
Parameter Description
VPI
VCI
ATM
Virtual Path Identifier. The valid range is from 0 to 255.
Virtual Circuit Identifier. The valid range is from 32 to 65535.
Encapsulation Mode Select LLC or VCMUX from the drop-down list.
QoS A class of traffic for this connection.
UBR
( Unspecified Bit Rate ): The UBR service is used for applications that allow various delays and losses of packets. It is appropriate to use the UBR service for text/data/image transfer applications, as well as messaging, distribution, retrieval, and remote terminal applications.
UBR with PCR
( Unspecified Bit Rate with Peak Cell Rate ): The UBR service is used for applications that allow various delays and losses of packets.
The Peak Cell Rate is a determining factor in how often cells are sent in an effort to minimize lag or jitter caused by traffic inconsistencies. When you select this value from the drop-down list, the Peak Cell Rate field is displayed. Specify a required value (in cells per second).
CBR
( Constant Bit Rate ): This service is used for applications that require a constant data rate. It is mostly used for transferring uncompressed audio and video, e.g. videoconferencing, interactive
Page 68 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Parameter
Configuring via Web-based Interface
Description audio (telephony), audio/video distribution (television, distance education, e-shops), and retrieval (video-on demand, audio libraries). When you select this value from the drop-down list, the
Peak Cell Rate field is displayed. Specify a required value (in cells per second).
Non Realtime VBR
( Non-Real-time Variable Bit Rate ): This service can be used for transferring data that have critical response-time requirements, e.g.
air ticket booking, bank transactions, and process monitoring. When you select this value from the drop-down list, the Peak Cell Rate ,
Sustainable Cell Rate , and Maximum Burst Size fields are displayed. Specify required values.
Realtime VBR
( Real-time Variable Bit Rate ): This service is used for delaysensitive applications such as real time video. The Rt-VBR provides higher network flexibility than the CBR service. When you select this value from the drop-down list, the Peak Cell Rate ,
Sustainable Cell Rate , and Maximum Burst Size fields are displayed. Specify required values.
Page 69 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Figure 53. The page for creating a new Static IPv4 connection. The IPv4 section.
Parameter Description
IPv4
For Static IPv4 and IPoA types
IP Address
Netmask
Gateway IP address
Primary DNS server/
Secondary DNS server
Enter an IP address for this WAN connection.
Enter a subnet mask for this WAN connection.
Enter an IP address of the gateway used by this WAN connection.
Enter addresses of the primary and secondary DNS servers in the relevant fields.
Obtain DNS server addresses automatically
Primary DNS server/
Secondary DNS server
Vendor ID
Host name
For Dynamic IPv4 type
Move the switch to the right to configure automatic assignment of
DNS server addresses. Upon that the Primary DNS server and
Secondary DNS server fields are not available for editing.
Enter addresses of the primary and secondary DNS servers in the relevant fields.
The identifier of your ISP. Optional .
A name of the router specified by your ISP. Optional .
Page 70 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Figure 54. The page for creating a new Static IPv4 connection. The Miscellaneous section.
Parameter Description
NAT
Firewall
Miscellaneous
If the switch is moved to the right, the network address translation function is enabled. Do not disable the function unless your ISP requires this.
If the switch is moved to the right, protection against external connections for the LAN devices is enabled (for example, against attempts to get information about the LAN devices or to hack a device from the LAN). For security reasons, it is recommended not to disable this function.
RIP
Ping
Move the switch to the right to allow using RIP for this connection.
If the switch is moved to the right, the router responds to ping requests from the external network through this connection. For security reasons, it is recommended to disable this function.
Page 71 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
The VLAN section is displayed for the Dynamic IPv4 and Static IPv4 types.
Figure 55. The page for creating a new Static IPv4 connection. The VLAN section.
Parameter Description
VLAN
Use VLAN
VLAN ID
Move the switch to the right to allow the router to use tagged VLAN connections.
An identifier for the VLAN. The field is displayed when the Use
VLAN switch is moved to the right.
VLAN priority
A priority tag for the type of traffic transmitted. The field is displayed when the Use VLAN switch is moved to the right.
When all needed settings are configured, click the APPLY button.
Page 72 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Creating Dynamic IPv6 or Static IPv6 WAN Connection
On the connection creation page, go to the All Settings tab. Then select the relevant value from the Connection Type drop-down list and specify the needed values.
Figure 56. The page for creating a new Static IPv6 connection. Selecting a connection type.
Parameter Description
Interface
Enable connection
Connection name
A physical interface to which the new connection will be assigned.
In order to create an Ethernet WAN connection, select the value corresponding to the LAN port specified as the WAN port.
In order to create an ADSL WAN connection, select the value corresponding to the existing interface or the Add new ATM PVC value for creating a new interface at the physical layer.
Move the switch to the right to enable the connection.
Move the switch to the left to disable the connection.
Available for the advanced mode only.
A name for the connection for easier identification.
Page 73 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
The Ethernet section is displayed for Ethernet WAN connections.
Configuring via Web-based Interface
Figure 57. The page for creating a new Static IPv6 connection. The Ethernet section.
Parameter Description
MAC address
Ethernet
A MAC address assigned to the interface. This parameter is mandatory if your ISP uses MAC address binding. In the field, enter the MAC address registered by your ISP upon concluding the agreement.
To set the MAC address of the network interface card (of the computer that is being used to configure the router at the moment) as the MAC address of the WAN interface, move the Clone MAC address of your NIC switch to the right. When the switch is moved to the right, the field is unavailable for editing.
To set the router's MAC address, click the RESTORE DEFAULT
MAC ADDRESS button (the button is available when the switch is moved to the right).
Page 74 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
The ATM section is displayed for ADSL WAN connections.
Configuring via Web-based Interface
Figure 58. The page for creating a new Static IPv6 connection. The ATM section.
Parameter Description
VPI
VCI
ATM
Virtual Path Identifier. The valid range is from 0 to 255.
Virtual Circuit Identifier. The valid range is from 32 to 65535.
Encapsulation Mode Select LLC or VCMUX from the drop-down list.
QoS A class of traffic for this connection.
UBR
( Unspecified Bit Rate ): The UBR service is used for applications that allow various delays and losses of packets. It is appropriate to use the UBR service for text/data/image transfer applications, as well as messaging, distribution, retrieval, and remote terminal applications.
UBR with PCR
( Unspecified Bit Rate with Peak Cell Rate ): The UBR service is used for applications that allow various delays and losses of packets.
The Peak Cell Rate is a determining factor in how often cells are sent in an effort to minimize lag or jitter caused by traffic inconsistencies. When you select this value from the drop-down list, the Peak Cell Rate field is displayed. Specify a required value (in cells per second).
CBR
( Constant Bit Rate ): This service is used for applications that require a constant data rate. It is mostly used for transferring uncompressed audio and video, e.g. videoconferencing, interactive
Page 75 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Parameter
Configuring via Web-based Interface
Description audio (telephony), audio/video distribution (television, distance education, e-shops), and retrieval (video-on demand, audio libraries). When you select this value from the drop-down list, the
Peak Cell Rate field is displayed. Specify a required value (in cells per second).
Non Realtime VBR
( Non-Real-time Variable Bit Rate ): This service can be used for transferring data that have critical response-time requirements, e.g.
air ticket booking, bank transactions, and process monitoring. When you select this value from the drop-down list, the Peak Cell Rate ,
Sustainable Cell Rate , and Maximum Burst Size fields are displayed. Specify required values.
Realtime VBR
( Real-time Variable Bit Rate ): This service is used for delaysensitive applications such as real time video. The Rt-VBR provides higher network flexibility than the CBR service. When you select this value from the drop-down list, the Peak Cell Rate ,
Sustainable Cell Rate , and Maximum Burst Size fields are displayed. Specify required values.
Page 76 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Figure 59. The page for creating a new Static IPv6 connection. The IPv6 section.
Parameter Description
IPv6
For Static IPv6 type
IPv6 address
Prefix
Enter an IPv6 address for this WAN connection.
The length of the subnet prefix. The value 64 is used usually.
Gateway IPv6 address Enter an IPv6 address of the gateway used by this WAN connection.
Primary IPv6 DNS server/Secondary IPv6
DNS server
Enter addresses of the primary and secondary IPv6 DNS servers in the relevant fields.
Get IPv6
Gateway by SLAAC
Gateway IPv6 address
For Dynamic IPv6 type
Select a method for IPv6 address assignment from the drop-down list or leave the Automatically value.
Move the switch to the right to automatically assign the IPv6 gateway address with help of SLAAC ( Stateless Address
Autoconfiguration ).
The address of the IPv6 gateway. The field is available for editing, if the Gateway by SLAAC switch is moved to the left.
Obtain DNS server addresses automatically
Move the switch to the right to configure automatic assignment of
IPv6 DNS server addresses. Upon that the Primary IPv6 DNS server and Secondary IPv6 DNS server fields are not available for editing.
Page 77 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Parameter
Primary IPv6 DNS server/Secondary IPv6
DNS server
Description
Enter addresses of the primary and secondary IPv6 DNS servers in the relevant fields.
Figure 60. The page for creating a new Static IPv6 connection. The Miscellaneous section.
Parameter Description
Firewall
RIP
Ping
Miscellaneous
If the switch is moved to the right, protection against external connections for the LAN devices is enabled (for example, against attempts to get information about the LAN devices or to hack a device from the LAN). For security reasons, it is recommended not to disable this function.
Move the switch to the right to allow using RIP for this connection.
If the switch is moved to the right, the router responds to ping requests from the external network through this connection. For security reasons, it is recommended to disable this function.
Page 78 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Figure 61. The page for creating a new Static IPv6 connection. The VLAN section.
Parameter Description
Use VLAN
VLAN
Move the switch to the right to allow the router to use tagged VLAN connections.
VLAN ID
An identifier for the VLAN. The field is displayed when the Use
VLAN switch is moved to the right.
VLAN priority
A priority tag for the type of traffic transmitted. The field is displayed when the Use VLAN switch is moved to the right.
When all needed settings are configured, click the APPLY button.
Page 79 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Creating PPPoE or PPPoA WAN Connection
On the connection creation page, go to the All Settings tab. Then select the relevant value from the Connection Type drop-down list and specify the needed values.
Figure 62. The page for creating a new PPPoE connection. Selecting a connection type.
Parameter Description
Interface
For the PPPoE type only.
A physical interface to which the new connection will be assigned.
In order to create an Ethernet WAN connection, select the value corresponding to the LAN port specified as the WAN port.
In order to create an ADSL WAN connection, select the value corresponding to the existing interface or the Add new ATM PVC value for creating a new interface at the physical layer.
Enable connection
Connection name
Move the switch to the right to enable the connection.
Move the switch to the left to disable the connection.
Available for the advanced mode only.
A name for the connection for easier identification.
Page 80 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
The Ethernet section is displayed for Ethernet WAN connections.
Configuring via Web-based Interface
Figure 63. The page for creating a new PPPoE connection. The Ethernet section.
Parameter Description
MAC address
Ethernet
A MAC address assigned to the interface. This parameter is mandatory if your ISP uses MAC address binding. In the field, enter the MAC address registered by your ISP upon concluding the agreement.
To set the MAC address of the network interface card (of the computer that is being used to configure the router at the moment) as the MAC address of the WAN interface, move the Clone MAC address of your NIC switch to the right. When the switch is moved to the right, the field is unavailable for editing.
To set the router's MAC address, click the RESTORE DEFAULT
MAC ADDRESS button (the button is available when the switch is moved to the right).
Page 81 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
The ATM section is displayed for ADSL WAN connections.
Configuring via Web-based Interface
Figure 64. The page for creating a new PPPoE connection. The ATM section.
Parameter Description
VPI
VCI
ATM
Virtual Path Identifier. The valid range is from 0 to 255.
Virtual Circuit Identifier. The valid range is from 32 to 65535.
Encapsulation Mode Select LLC or VCMUX from the drop-down list.
QoS A class of traffic for this connection.
UBR
( Unspecified Bit Rate ): The UBR service is used for applications that allow various delays and losses of packets. It is appropriate to use the UBR service for text/data/image transfer applications, as well as messaging, distribution, retrieval, and remote terminal applications.
UBR with PCR
( Unspecified Bit Rate with Peak Cell Rate ): The UBR service is used for applications that allow various delays and losses of packets.
The Peak Cell Rate is a determining factor in how often cells are sent in an effort to minimize lag or jitter caused by traffic inconsistencies. When you select this value from the drop-down list, the Peak Cell Rate field is displayed. Specify a required value (in cells per second).
CBR
( Constant Bit Rate ): This service is used for applications that require a constant data rate. It is mostly used for transferring uncompressed audio and video, e.g. videoconferencing, interactive
Page 82 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Parameter
Configuring via Web-based Interface
Description audio (telephony), audio/video distribution (television, distance education, e-shops), and retrieval (video-on demand, audio libraries). When you select this value from the drop-down list, the
Peak Cell Rate field is displayed. Specify a required value (in cells per second).
Non Realtime VBR
( Non-Real-time Variable Bit Rate ): This service can be used for transferring data that have critical response-time requirements, e.g.
air ticket booking, bank transactions, and process monitoring. When you select this value from the drop-down list, the Peak Cell Rate ,
Sustainable Cell Rate , and Maximum Burst Size fields are displayed. Specify required values.
Realtime VBR
( Real-time Variable Bit Rate ): This service is used for delaysensitive applications such as real time video. The Rt-VBR provides higher network flexibility than the CBR service. When you select this value from the drop-down list, the Peak Cell Rate ,
Sustainable Cell Rate , and Maximum Burst Size fields are displayed. Specify required values.
Page 83 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Figure 65. The page for creating a new PPPoE connection. The PPP section.
Parameter Description
PPP
Without authorization
Username
Password
Service name
MTU
Move the switch to the right if you don't need to enter a username and password to access the Internet.
A username (login) to access the Internet.
A password to access the Internet. Click the Show icon ( ) to display the entered password.
For the PPPoE type only.
The name of the PPPoE authentication server.
The maximum size of units transmitted by the interface.
Page 84 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Parameter
Authentication protocol
Keep Alive
Dial on demand
Static IP Address
PPP IP extension
PPP debug
Configuring via Web-based Interface
Select a required authentication method from the drop-down list or leave the AUTO value.
Description
Move the switch to the right if you want the router to keep you connected to your ISP even when the connection has been inactive for a specified period of time. If the switch is moved to the right, the
LCP interval and LCP fails fields are available. Specify the required values.
Move the switch to the right if you want the router to establish connection to the Internet on demand. In the Maximum idle time field, specify a period of inactivity (in seconds) after which the connection should be terminated.
Fill in the field if you want to use a static IP address to access the
Internet.
This option is used by some ISPs. Contact your ISP to clarify if this option needs to be enabled. If it is required, move the switch to the right.
Move the switch to the right if you want to log all data on PPP connection debugging.
Page 85 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Figure 66. The page for creating a new PPPoE connection. The Miscellaneous section.
Parameter Description
NAT
Firewall
Miscellaneous
If the switch is moved to the right, the network address translation function is enabled. Do not disable the function unless your ISP requires this.
If the switch is moved to the right, protection against external connections for the LAN devices is enabled (for example, against attempts to get information about the LAN devices or to hack a device from the LAN). For security reasons, it is recommended not to disable this function.
RIP
Ping
Move the switch to the right to allow using RIP for this connection.
If the switch is moved to the right, the router responds to ping requests from the external network through this connection. For security reasons, it is recommended to disable this function.
Page 86 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
The VLAN section is displayed for the PPPoE type.
Configuring via Web-based Interface
Figure 67. The page for creating a new PPPoE connection. The VLAN section.
Parameter Description
VLAN
Use VLAN
VLAN ID
Move the switch to the right to allow the router to use tagged VLAN connections.
An identifier for the VLAN. The field is displayed when the Use
VLAN switch is moved to the right.
VLAN priority
A priority tag for the type of traffic transmitted. The field is displayed when the Use VLAN switch is moved to the right.
When all needed settings are configured, click the APPLY button.
Page 87 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Creating PPPoE IPv6 or PPPoE Dual Stack WAN Connection
On the connection creation page, go to the All Settings tab. Then select the relevant value from the Connection Type drop-down list and specify the needed values.
Figure 68. The page for creating a new PPPoE IPv6 connection. Selecting a connection type.
Parameter Description
Interface
Enable connection
Connection name
A physical interface to which the new connection will be assigned.
In order to create an Ethernet WAN connection, select the value corresponding to the LAN port specified as the WAN port.
In order to create an ADSL WAN connection, select the value corresponding to the existing interface or the Add new ATM PVC value for creating a new interface at the physical layer.
Move the switch to the right to enable the connection.
Move the switch to the left to disable the connection.
Available for the advanced mode only.
A name for the connection for easier identification.
Page 88 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
The Ethernet section is displayed for Ethernet WAN connections.
Configuring via Web-based Interface
Figure 69. The page for creating a new PPPoE IPv6 connection. The Ethernet section.
Parameter Description
MAC address
Ethernet
A MAC address assigned to the interface. This parameter is mandatory if your ISP uses MAC address binding. In the field, enter the MAC address registered by your ISP upon concluding the agreement.
To set the MAC address of the network interface card (of the computer that is being used to configure the router at the moment) as the MAC address of the WAN interface, move the Clone MAC address of your NIC switch to the right. When the switch is moved to the right, the field is unavailable for editing.
To set the router's MAC address, click the RESTORE DEFAULT
MAC ADDRESS button (the button is available when the switch is moved to the right).
Page 89 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
The ATM section is displayed for ADSL WAN connections.
Configuring via Web-based Interface
Figure 70. The page for creating a new PPPoE IPv6 connection. The ATM section.
Parameter Description
VPI
VCI
ATM
Virtual Path Identifier. The valid range is from 0 to 255.
Virtual Circuit Identifier. The valid range is from 32 to 65535.
Encapsulation Mode Select LLC or VCMUX from the drop-down list.
QoS A class of traffic for this connection.
UBR
( Unspecified Bit Rate ): The UBR service is used for applications that allow various delays and losses of packets. It is appropriate to use the UBR service for text/data/image transfer applications, as well as messaging, distribution, retrieval, and remote terminal applications.
UBR with PCR
( Unspecified Bit Rate with Peak Cell Rate ): The UBR service is used for applications that allow various delays and losses of packets.
The Peak Cell Rate is a determining factor in how often cells are sent in an effort to minimize lag or jitter caused by traffic inconsistencies. When you select this value from the drop-down list, the Peak Cell Rate field is displayed. Specify a required value (in cells per second).
CBR
( Constant Bit Rate ): This service is used for applications that require a constant data rate. It is mostly used for transferring uncompressed audio and video, e.g. videoconferencing, interactive
Page 90 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Parameter
Configuring via Web-based Interface
Description audio (telephony), audio/video distribution (television, distance education, e-shops), and retrieval (video-on demand, audio libraries). When you select this value from the drop-down list, the
Peak Cell Rate field is displayed. Specify a required value (in cells per second).
Non Realtime VBR
( Non-Real-time Variable Bit Rate ): This service can be used for transferring data that have critical response-time requirements, e.g.
air ticket booking, bank transactions, and process monitoring. When you select this value from the drop-down list, the Peak Cell Rate ,
Sustainable Cell Rate , and Maximum Burst Size fields are displayed. Specify required values.
Realtime VBR
( Real-time Variable Bit Rate ): This service is used for delaysensitive applications such as real time video. The Rt-VBR provides higher network flexibility than the CBR service. When you select this value from the drop-down list, the Peak Cell Rate ,
Sustainable Cell Rate , and Maximum Burst Size fields are displayed. Specify required values.
Page 91 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Figure 71. The page for creating a new PPPoE IPv6 connection. The PPP section.
Parameter Description
Without authorization
Username
PPP
Move the switch to the right if you don't need to enter a username and password to access the Internet.
A username (login) to access the Internet.
Password
Service name
MTU
Authentication protocol
A password to access the Internet. Click the Show icon ( ) to display the entered password.
The name of the PPPoE authentication server.
The maximum size of units transmitted by the interface.
Select a required authentication method from the drop-down list or leave the AUTO value.
Page 92 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Parameter
Keep Alive
Dial on demand
Static IP Address
PPP IP extension
PPP debug
Configuring via Web-based Interface
Description
Move the switch to the right if you want the router to keep you connected to your ISP even when the connection has been inactive for a specified period of time. If the switch is moved to the right, the
LCP interval and LCP fails fields are available. Specify the required values.
Move the switch to the right if you want the router to establish connection to the Internet on demand. In the Maximum idle time field, specify a period of inactivity (in seconds) after which the connection should be terminated.
For the PPPoE Dual Stack type only.
Fill in the field if you want to use a static IP address to access the
Internet.
This option is used by some ISPs. Contact your ISP to clarify if this option needs to be enabled. If it is required, move the switch to the right.
Move the switch to the right if you want to log all data on PPP connection debugging.
Page 93 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Figure 72. The page for creating a new PPPoE Pv6 connection. The IP section.
Parameter Description
IP
Get IPv6
Gateway by SLAAC
Gateway IPv6 address
Obtain DNS server addresses automatically
Select a method for IPv6 address assignment from the drop-down list or leave the Automatically value.
Move the switch to the right to automatically assign the IPv6 gateway address with help of SLAAC ( Stateless Address
Autoconfiguration ).
The address of the IPv6 gateway. The field is available for editing, if the Gateway by SLAAC switch is moved to the left.
Move the switch to the right to configure automatic assignment of
IPv6 DNS server addresses. Upon that the Primary IPv6 DNS server and Secondary IPv6 DNS server fields are not available for editing.
Primary IPv6 DNS server/Secondary IPv6
DNS server
Enter addresses of the primary and secondary IPv6 DNS servers in the relevant fields.
Page 94 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Figure 73. The page for creating a new PPPoE IPv6 connection. The Miscellaneous section.
Parameter Description
NAT
Firewall
RIP
Ping
Miscellaneous
For the PPPoE Dual Stack type only.
If the switch is moved to the right, the network address translation function is enabled. Do not disable the function unless your ISP requires this.
If the switch is moved to the right, protection against external connections for the LAN devices is enabled (for example, against attempts to get information about the LAN devices or to hack a device from the LAN). For security reasons, it is recommended not to disable this function.
Move the switch to the right to allow using RIP for this connection.
If the switch is moved to the right, the router responds to ping requests from the external network through this connection. For security reasons, it is recommended to disable this function.
Page 95 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Figure 74. The page for creating a new PPPoE IPv6 connection. The VLAN section.
Parameter Description
Use VLAN
VLAN
Move the switch to the right to allow the router to use tagged VLAN connections.
VLAN ID
An identifier for the VLAN. The field is displayed when the Use
VLAN switch is moved to the right.
VLAN priority
A priority tag for the type of traffic transmitted. The field is displayed when the Use VLAN switch is moved to the right.
When all needed settings are configured, click the APPLY button.
Page 96 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Creating Bridge WAN Connection
On the connection creation page, go to the All Settings tab. Then select the relevant value from the Connection Type drop-down list and specify the needed values.
Figure 75. The page for creating a new Bridge connection. Selecting a connection type.
Parameter Description
Interface
A physical interface to which the new connection will be assigned.
In order to create an Ethernet WAN connection, select the value corresponding to the LAN port specified as the WAN port.
In order to create an ADSL WAN connection, select the value corresponding to the existing interface or the Add new ATM PVC value for creating a new interface at the physical layer.
Enable connection
Connection name
Move the switch to the right to enable the connection.
Move the switch to the left to disable the connection.
Available for the advanced mode only.
A name for the connection for easier identification.
Page 97 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
The Ethernet section is displayed for Ethernet WAN connections.
Configuring via Web-based Interface
Figure 76. The page for creating a new Bridge connection. The Ethernet section.
Parameter Description
MAC address
Ethernet
A MAC address assigned to the interface. This parameter is mandatory if your ISP uses MAC address binding. In the field, enter the MAC address registered by your ISP upon concluding the agreement.
To set the MAC address of the network interface card (of the computer that is being used to configure the router at the moment) as the MAC address of the WAN interface, move the Clone MAC address of your NIC switch to the right. When the switch is moved to the right, the field is unavailable for editing.
To set the router's MAC address, click the RESTORE DEFAULT
MAC ADDRESS button (the button is available when the switch is moved to the right).
Page 98 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
The ATM section is displayed for ADSL WAN connections.
Configuring via Web-based Interface
Figure 77. The page for creating a new Bridge connection. The ATM section.
Parameter Description
VPI
VCI
ATM
Virtual Path Identifier. The valid range is from 0 to 255.
Virtual Circuit Identifier. The valid range is from 32 to 65535.
Encapsulation Mode Select LLC or VCMUX from the drop-down list.
QoS A class of traffic for this connection.
UBR
( Unspecified Bit Rate ): The UBR service is used for applications that allow various delays and losses of packets. It is appropriate to use the UBR service for text/data/image transfer applications, as well as messaging, distribution, retrieval, and remote terminal applications.
UBR with PCR
( Unspecified Bit Rate with Peak Cell Rate ): The UBR service is used for applications that allow various delays and losses of packets.
The Peak Cell Rate is a determining factor in how often cells are sent in an effort to minimize lag or jitter caused by traffic inconsistencies. When you select this value from the drop-down list, the Peak Cell Rate field is displayed. Specify a required value (in cells per second).
CBR
( Constant Bit Rate ): This service is used for applications that require a constant data rate. It is mostly used for transferring uncompressed audio and video, e.g. videoconferencing, interactive
Page 99 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Parameter
Configuring via Web-based Interface
Description audio (telephony), audio/video distribution (television, distance education, e-shops), and retrieval (video-on demand, audio libraries). When you select this value from the drop-down list, the
Peak Cell Rate field is displayed. Specify a required value (in cells per second).
Non Realtime VBR
( Non-Real-time Variable Bit Rate ): This service can be used for transferring data that have critical response-time requirements, e.g.
air ticket booking, bank transactions, and process monitoring. When you select this value from the drop-down list, the Peak Cell Rate ,
Sustainable Cell Rate , and Maximum Burst Size fields are displayed. Specify required values.
Realtime VBR
( Real-time Variable Bit Rate ): This service is used for delaysensitive applications such as real time video. The Rt-VBR provides higher network flexibility than the CBR service. When you select this value from the drop-down list, the Peak Cell Rate ,
Sustainable Cell Rate , and Maximum Burst Size fields are displayed. Specify required values.
Page 100 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Figure 78. The page for creating a new Bridge connection. The VLAN section.
Parameter Description
Use VLAN
VLAN
Move the switch to the right to allow the router to use tagged VLAN connections.
VLAN ID
An identifier for the VLAN. The field is displayed when the Use
VLAN switch is moved to the right.
VLAN priority
A priority tag for the type of traffic transmitted. The field is displayed when the Use VLAN switch is moved to the right.
When all needed settings are configured, click the APPLY button.
Page 101 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Creating 3G WAN Connection
If the PIN code check is enabled for the SIM card inserted into your USB modem, then prior to creating a 3G WAN connection, go to the USB Modem menu and enter the PIN code 8 on the page displayed (see the USB Modem section, page 152). Then on the connection creation page, go to the
All Settings tab, select the relevant value from the Connection Type drop-down list, and specify the needed values.
Figure 79. The page for creating a new 3G connection. Selecting a connection type.
Parameter Description
Enable connection
Connection name
Move the switch to the right to enable the connection.
Move the switch to the left to disable the connection.
Available for the advanced mode only.
A name for the connection for easier identification.
8 For some models of 3G USB modems it is required to disable the PIN code check on the SIM card prior to connecting the USB modem to the router.
Page 102 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Figure 80. The page for creating a new 3G connection. The USB Modem section.
Parameter Description
Mode
APN
Dial number
USB Modem
The value of the field specifies the type of the network to which the router connects. Leave the Auto value to let the router connect automatically to an available type of network, or select a needed value from the drop-down list.
An access point name.
A number dialed to connect to the authorization server of the operator.
Figure 81. The page for creating a new 3G connection. The PPP section.
Page 103 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Parameter
Without authorization
Username
Password
MTU
Authentication protocol
Keep Alive
Dial on demand
PPP debug
Description
PPP
Move the switch to the right if your operator does not require authorization.
A username (login) to connect to the network of the operator.
A password to connect to the network of the operator. Click the
Show icon ( ) to display the entered password.
The maximum size of units transmitted by the interface.
Select a required authentication method from the drop-down list or leave the AUTO value.
Move the switch to the right if you want the router to keep you connected to the network of your operator even when the connection has been inactive for a specified period of time. When the checkbox is selected, the LCP interval and LCP fails fields are available. Specify the required values.
Move the switch to the right if you want the router to establish connection to the Internet on demand. In the Maximum idle time field, specify a period of inactivity (in seconds) after which the connection should be terminated.
Move the switch to the right if you want to log all data on PPP connection debugging.
Page 104 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Figure 82. The page for creating a new 3G connection. The Miscellaneous section.
Parameter Description
NAT
Miscellaneous
If the switch is moved to the right, the network address translation function is enabled. Do not disable the function unless your ISP requires this.
Firewall
If the switch is moved to the right, protection against external connections for the LAN devices is enabled (for example, against attempts to get information about the LAN devices or to hack a device from the LAN). For security reasons, it is recommended not to disable this function.
Ping
If the switch is moved to the right, the router responds to ping requests from the external network through this connection. For security reasons, it is recommended to disable this function.
When all needed settings are configured, click the APPLY button.
Page 105 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Creating LTE WAN Connection
!
For the USB modem Megafon M100-1, please reboot the router after creating the WAN connection.
If the PIN code check is enabled for the SIM card inserted into your USB modem, then prior to creating an LTE WAN connection, go to the USB Modem menu and enter the PIN code 9 on the page displayed (see the USB Modem section, page 152). Then on the connection creation page, go to the All Settings tab, select the relevant value from the Connection Type drop-down list, and specify the needed values.
Figure 83. The page for creating a new LTE connection. Selecting a connection type.
Parameter Description
Enable connection
Connection name
Move the switch to the right to enable the connection.
Move the switch to the left to disable the connection.
Available for the advanced mode only.
A name for the connection for easier identification.
9 For some models of LTE USB modems it is required to disable the PIN code check on the SIM card prior to connecting the USB modem to the router.
Page 106 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Figure 84. The page for creating a new LTE connection. The USB Modem section.
Parameter Description
Mode
APN
Without authorization
USB Modem
The value of the field specifies the type of the network to which the router connects. Leave the Auto value to let the router connect automatically to an available type of network, or select a needed value from the drop-down list.
10
An access point name.
Move the switch to the right if your operator does not require authorization.
Authentication protocol
Username
Select a required authentication method from the drop-down list.
Password
A username (login) to connect to the network of the operator.
A password to connect to the network of the operator. Click the
Show icon ( ) to display the entered password.
10 Some LTE USB modems do not support network type selection and work in the Auto mode regardless of the value selected from the drop-down list.
Page 107 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Figure 85. The page for creating a new LTE connection. The IPv4 section.
Parameter Description
Obtain DNS server addresses automatically
Primary DNS server/
Secondary DNS server
IPv4
Move the switch to the right to configure automatic assignment of
DNS server addresses. Upon that the Primary DNS server and
Secondary DNS server fields are not available for editing.
Enter addresses of the primary and secondary DNS servers in the relevant fields.
Vendor ID
Hostname
The identifier of your ISP. Optional .
A name of the router specified by your ISP. Optional .
Page 108 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Figure 86. The page for creating a new LTE connection. The Miscellaneous section.
Parameter Description
NAT
Miscellaneous
If the switch is moved to the right, the network address translation function is enabled. Do not disable the function unless your ISP requires this.
Firewall
If the switch is moved to the right, protection against external connections for the LAN devices is enabled (for example, against attempts to get information about the LAN devices or to hack a device from the LAN). For security reasons, it is recommended not to disable this function.
Ping
If the switch is moved to the right, the router responds to ping requests from the external network through this connection. For security reasons, it is recommended to disable this function.
When all needed settings are configured, click the APPLY button.
Page 109 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
LAN
To configure the router's local interface, go to the Connections Setup / LAN page.
IPv4
Go to the IPv4 tab to change IPv4 address, configure the built-in DHCP server, or specify MAC address and IP address pairs.
Figure 87. Configuring the local interface. The IPv4 tab. The Local IP Address section.
Parameter Description
Local IP Address
IP address
Subnet mask
The IP address of the router in the local subnet. By default, the following value is specified: 192.168.1.1
.
The mask of the local subnet. By default, the following value is specified: 255.255.255.0
.
Device domain name The name of the device attached to its IP address in the local subnet.
Figure 88. Configuring the local interface. The IPv4 tab. The Dynamic IP Addresses section.
Page 110 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Parameter Description
Dynamic IP Addresses
Mode of dynamic IP address assignment
Start IP
End IP
Lease time
An operating mode of the router's DHCP server.
Disable : the router's DHCP server is disabled, clients' IP addresses are assigned manually.
DHCP server : the router assigns IP addresses to clients automatically in accordance with the specified parameters. When this value is selected, the Start IP , End IP , Lease time fields and the DNS relay switch are displayed on the tab.
DHCP relay : an external DHCP server is used to assign IP addresses to clients. When this value is selected, the External
DHCP server IP field is displayed on the tab.
The start IP address of the address pool used by the DHCP server to distribute IP addresses to clients.
The end IP address of the address pool used by the DHCP server to distribute IP addresses to clients.
The lifetime of IP addresses leased by the DHCP server. At the end of this period the leased IP address is revoked and can be distributed to another device, unless the previous device has confirmed the need to keep the address.
DNS Relay
Move the switch to the right so that the devices connected to the router obtain the address of the router as the DNS server address.
Move the switch to the left so that the devices connected to the router obtain the address transmitted by the ISP or specified on the
Advanced / DNS page as the DNS server address.
External DHCP server IP
The IP address of the external DHCP server which assigns IP addresses to the router's clients.
When all needed settings are configured, click the APPLY button.
Page 111 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
In the Static IP Addresses section, you can specify MAC address and IP address pairs (set a fixed IPv4 address in the local area network for a device with a certain MAC address). The router assigns IP addresses in accordance with the specified pairs only when the DHCP server is enabled
(in the Dynamic IP Addresses section, the DHCP server value is selected from the Mode of dynamic IP address assignment drop-down list).
Figure 89. The section for creating MAC-IP pairs.
To create a MAC-IP pair, click the ADD button. In the opened window, in the IP address field, enter an IPv4 address which will be assigned to the device from the LAN, then in the MAC address field, enter the MAC address of this device. In the Host field, specify a network name of the device for easier identification ( optional ). Click the APPLY button.
Also you can create a MAC-IP pair for a device connected to the router's LAN at the moment. To do this, click the CLIENTS LIST button. In the opened window, select the relevant device and click the OK button. To view the latest list of the connected devices, click the REFRESH button.
To edit the settings for the existing MAC-IP pair, left-click the relevant line in the table. In the opened window, change the needed parameters and click the APPLY button.
To remove a MAC-IP pair, select the checkbox located to the left of the relevant line in the table and click the DELETE button. Then click the APPLY button. Also you can remove a MAC-IP pair in the editing window.
Page 112 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
IPv6
Go to the IPv6 tab to change IPv6 address of the router and configure IPv6 addresses assignment settings.
Figure 90. Configuring the local interface. The IPv6 tab. The Local IPv6 Address section.
Parameter Description
Mode of local IPv6 address assignment
IPv6 address
Prefix
Local IPv6 Address
Select the needed value from the drop-down list.
Static : an IPv6 address and a prefix are specified manually.
Prefix delegation : the router requests a prefix to configure an
IPv6 address from a delegating router.
The IPv6 address of the router in the local subnet. By default, the following value is specified: fd01::1 . The field is available for editing, if the Static value is selected from the Mode of local
IPv6 address assignment drop-down list.
The length of the prefix subnet. By default, the value 64 is specified. The field is available for editing, if the Static value is selected from the Mode of local IPv6 address assignment drop-down list.
Page 113 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Figure 91. Configuring the local interface. The IPv6 tab. The Dynamic IPv6 Addresses section.
Parameter Description
Dynamic IPv6 Addresses
Mode of dynamic IPv6 address assignment
Start IPv6
End IPv6
Select the needed value from the drop-down list.
Disable : clients' IPv6 addresses are assigned manually.
Stateful : the built-in DHCPv6 server of the router allocates addresses from the range specified in the Start IPv6 and End IPv6 fields.
Stateless : clients themselves configure IPv6 addresses using the prefix.
The start IPv6 address of the address pool used by the DHCPv6 server to distribute addresses to clients.
The end IPv6 address of the address pool used by the DHCPv6 server to distribute addresses to clients.
Lease Time
The lifetime of IPv6 addresses provided to clients. The field is available for editing, if the Static value is selected from the Mode of local IPv6 address assignment list in the Local IPv6
Address section.
When all needed settings are configured, click the APPLY button.
Page 114 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
WAN Reservation
On the Connections Setup / WAN Reservation page, you can enable the WAN backup function, which provides you with uninterrupted access to the Internet. When your main connection breaks down, the router activates the backup connection; and when the main channel is recovered, the router switches to it and disconnects the reserve one.
Figure 92. The Connections Setup / WAN Reservation page.
To activate the backup function, create the main and the reserve WAN connections. After that go to the Connections Setup / WAN Reservation page, move the Enable switch to the right, and specify the needed values in the fields displayed on the page.
Parameter Description
Basic connection
Backup connection
Test host
Check interval
Timeout check
From the drop-down list, select a WAN connection which will be used as the main one.
From the drop-down list, select a WAN connection which will be used as the reserve one.
An IP address that the router will check for availability via ICMP ping mechanism.
A time period (in seconds) between attempts to check the status of the main connection. By default, the value 10 is specified.
A time period (in seconds) for an attempt to check the status of the main connection. At the end of this period the router's internal system makes a decision to enable/disable the reserve channel. By default, the value 3 is specified.
Page 115 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Parameter Description
Number of inspections of active connection
A number of requests that will be sent in order to analyze the status of the main connection when the connection is active (the router uses the main connection as a default gateway).
Number of inspections of inactive connection
A number of requests that will be sent in order to analyze the status of the main connection when the connection is inactive (the router uses the reserve connection as a default gateway).
When all needed settings are configured, click the APPLY button.
Page 116 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Wi-Fi
In this menu you can specify all needed settings for your wireless network.
Basic Settings
In the Wi-Fi / Basic Settings section, you can change basic parameters for the wireless interface of the router and configure the basic and additional wireless networks.
Figure 93. Basic settings of the wireless LAN.
Page 117 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
In the General Settings section, the following parameters are available:
Parameter
Enable Wireless
Description
To enable Wi-Fi connection, move the switch to the right.
To disable Wi-Fi connection, move the switch to the left.
The country you are in. Select a value from the drop-down list.
Country
Wireless mode
Select channel automatically
Operating mode of the wireless network of the router. This parameter defines standards of the devices that will be able to use your wireless network. Select a value from the drop-down list.
Move the switch to the right to let the router itself choose the channel with the least interference.
Channel
Enable periodic scanning
The wireless channel number. Left-click to open the window for selecting a channel (the action is available, when the Select channel automatically switch is moved to the left).
Move the switch to the right to let the router search for a free channel in certain periods of time. When the switch is moved to the right, the Scanning period field is available for editing.
Scanning period
Specify a period of time (in seconds) after which the router rescans channels.
When you have configured the parameters, click the APPLY button.
To edit the settings of the basic wireless network, in the Wi-Fi Network section, change the needed parameters and click the APPLY button.
Page 118 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Also you can create an additional wireless network. To do this, click the ADD WI-FI NETWORK button. On the opened page, specify the relevant parameters.
Figure 94. Creating a wireless network.
Page 119 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Parameter
Network name (SSID)
Hide SSID
BSSID
Max associated clients
Enable shaping
Broadcast wireless network
Clients isolation
Enable guest network
Description
Wi-Fi Network
A name for the wireless network. The name can consist of digits and
Latin characters.
If the switch is moved to the right, other users cannot see your Wi-Fi network. It is recommended not to hide the network in order to simplify initial configuration of the wireless network.
The unique identifier for this wireless network. You cannot change the value of this parameter, it is determined in the device's internal settings. The field is displayed in the settings of the existing wireless network.
The maximum number of devices connected to the wireless network.
When the value 0 is specified, the device does not limit the number of connected clients.
Move the switch to the right to limit the maximum bandwidth of the wireless network. In the Shaping field displayed, specify the maximum value of speed (Kbit/s).
Move the switch to the left not to limit the maximum bandwidth.
If the switch is moved to the left, devices cannot connect to the wireless network. Upon that the router can connect to another access point as a wireless client.
Move the switch to the right to forbid wireless clients of this wireless network to communicate to each other.
This function is available for the additional network. Move the switch to the right if you want the devices connected to the additional network to be isolated from the devices and resources of the router's LAN.
Page 120 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
In the Security Settings section, you can change security settings of the wireless network.
By default, the WPA2-PSK network authentication type of the wireless network is specified. WPS
PIN from the barcode label is used as the network key.
Figure 95. Network authentication types supported by the router.
The router supports the following authentication types:
Authentication type Description
Open
WEP-64
WEP-128
WPA
Open authentication (with WEP encryption for wireless network modes not supporting 802.11n devices).
Authentication with a 64-bit shared key with WEP encryption. This authentication type is not available when a mode supporting 802.11n
devices is selected from the Wireless mode drop-down list on the
Wi-Fi / Basic Settings page.
Authentication with a 128-bit shared key with WEP encryption. This authentication type is not available when a mode supporting 802.11n
devices is selected from the Wireless mode drop-down list on the
Wi-Fi / Basic Settings page.
WPA-based authentication using a RADIUS server.
WPA-PSK
WPA2
WPA2-PSK
WPA-based authentication using a PSK.
WPA2-based authentication using a RADIUS server.
WPA/WPA2 mixed
WPA2-based authentication using a PSK.
A mixed type of authentication. When this value is selected, devices using the WPA authentication type and devices using the WPA2 authentication type can connect to the wireless network.
Page 121 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Authentication type Description
WPA-PSK/WPA2-PSK mixed
A mixed type of authentication. When this value is selected, devices using the WPA-PSK authentication type and devices using the
WPA2-PSK authentication type can connect to the wireless network.
!
The WPA , WPA2 , and WPA/WPA2 mixed authentication types require a RADIUS server.
When the Open , WEP-64 , or WEP-128 value is selected, the following settings are displayed on the page (unavailable for the wireless network operating modes which support the standard
802.11n):
Figure 96. The Open value is selected from the Network authentication drop-down list.
Page 122 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Parameter Description
Enable encryption WEP
For Open authentication type only.
To activate WEP encryption, move the switch to the right. Upon that the WEP type and Default key ID drop-down lists, the
Encryption key WEP as HEX switch, and four Encryption key fields are displayed on the page.
WEP type
Default key ID
Encryption key WEP as
HEX
Encryption key
(1-4)
For Open authentication type only.
WEP encryption type with a 64-bit or 128-bit key.
Select the WEP-64 value to specify keys containing 5 ASCII symbols or 10 HEX symbols.
Select the WEP-128 value to specify keys containing 13 ASCII symbols or 26 HEX symbols.
The number of the key (from first to fourth) which will be used for
WEP encryption.
Move the switch to the right to set a hexadecimal number as a key for encryption.
Keys for WEP encryption. The router uses the key selected from the
Default key ID drop-down list. It is required to specify all the fields. Click the Show icon ( ) to display the entered key.
Page 123 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
When the WPA-PSK , WPA2-PSK , or WPA-PSK/WPA2-PSK mixed value is selected, the following fields are displayed on the page:
Figure 97. The WPA2-PSK value is selected from the Network authentication drop-down list.
Parameter
Password PSK
Encryption type
Description
A password for WPA encryption. The password can contain digits,
Latin letters (uppercase and/or lowercase), and other characters available in the US keyboard layout.
11 Click the Show icon ( ) to display the entered password.
An encryption method: TKIP , AES , or TKIP+AES .
Group key update interval
The time period (in seconds), at the end of which a new key for WPA encryption is generated. When the value 0 is specified for this field, the key is not renewed.
11 0-9, A-Z, a-z, space, !"#$%&'()*+,-./:;<=>?@[\]^_`{|}~.
Page 124 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
When the WPA , WPA2 , or WPA/WPA2 mixed value is selected, the following settings are displayed on the page:
Figure 98. The WPA2 value is selected from the Network authentication drop-down list.
Parameter Description
WPA2 Preauthentication
Move the switch to the right to activate preliminary authentication
(displayed only for the WPA2 and WPA/WPA2 mixed authentication types).
IP address RADIUS server
The IP address of the RADIUS server.
RADIUS server port A port of the RADIUS server.
RADIUS encryption key
The password which the router uses for communication with the
RADIUS server (the value of this parameter is specified in the
RADIUS server settings).
Encryption type An encryption method: TKIP , AES , or TKIP+AES .
Group key update interval
The time period (in seconds), at the end of which a new key for WPA encryption is generated. When the value 0 is specified for this field, the key is not renewed.
When you have configured the parameters, click the APPLY button.
To edit the basic or additional wireless network, left-click the relevant line in the table. On the opened page, change the needed parameters and click the APPLY button.
To remove the additional network, select the checkbox located to the left of the relevant line in the table and click the DELETE button. Then click the APPLY button.
Page 125 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Client Management
On the Wi-Fi / Client Management page, you can view the list of wireless clients connected to the router.
Figure 99. The page for managing the wireless clients.
If you want to disconnect a wireless device from your WLAN, select the checkbox in the line containing the MAC address of this device and click the DISCONNECT button.
To view the latest data on the devices connected to the WLAN, click the REFRESH button.
Page 126 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
WPS
On the Wi-Fi / WPS page, you can enable the function for configuration of the WLAN and select a method for connection to the WLAN.
The WPS function helps to configure the protected wireless network automatically. Devices connecting to the wireless network via the WPS function must support the WPS function.
!
!
The WPS function allows adding devices only to the basic wireless network of the router.
Before using the function you need to configure one of the following authentication types:
Open with no encryption, WPA2-PSK or WPA-PSK/WPA2-PSK mixed with the AES encryption method. When other security settings are specified, controls of the WPS page are not available.
Figure 100. The page for configuring the WPS function.
To activate the WPS function, click the ENABLE WPS button.
Page 127 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
When the WPS function is enabled, the Information section is available on the page.
Parameter
WPS state
Default PIN code
Description
The state of the WPS function:
• Configured (all needed settings are specified; these settings will be used upon establishing the wireless connection)
• Unconfigured (after activating the WPS function, the SSID and the encryption key will be configured automatically, the network authentication type will be changed to WPA2-PSK).
The PIN code of the router. This parameter is used when connecting the router to a registrar to set the parameters of the WPS function.
Network name (SSID) The name of the router's wireless network.
Network Authentication The network authentication type specified for the wireless network.
Encryption The encryption type specified for the wireless network.
Password PSK
UPDATE
RESET TO
UNCONFIGURED
The encryption password specified for the wireless network.
Click the button to update the data on the page.
Click the button to reset the parameters of the WPS function.
Page 128 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Using WPS Function via Web-based Interface
To connect to the basic wireless network via the PIN method of the WPS function, follow the next steps:
1. Click the ENABLE WPS button.
2. In the WPS Control section, click the ESTABLISH CONNECTION button.
3. In the opened window, select the PIN value from the WPS method drop-down list.
4. Select the PIN method in the software of the wireless device that you want to connect to the router's WLAN.
5. Click the relevant button in the software of the wireless device that you want to connect to the WLAN.
6. Right after that, enter the PIN code specified on the cover of the wireless device or in its software in the PIN Code field.
7. Click the CONNECT button in the web-based interface of the router.
To connect to the basic wireless network via the PBC method of the WPS function, follow the next steps:
1. Click the ENABLE WPS button.
2. In the WPS Control section, click the ESTABLISH CONNECTION button.
3. In the opened window, select the PBC value from the WPS method drop-down list.
4. Select the PBC method in the software of the wireless device that you want to connect to the router's WLAN.
5. Click the relevant button in the software or press the WPS button on the cover of the wireless device that you want to connect to the WLAN.
6. Right after that, click the CONNECT button in the web-based interface of the router.
Page 129 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Using WPS Function without Web-based Interface
You can use the WPS function without accessing the web-based interface of the router. To do this, you need to configure the following router's settings:
1. Specify relevant security settings for the wireless network of the router.
2. Click the ENABLE WPS button.
3. Save the settings and close the web-based interface (click the SAVE button in the notification and then click the Logout line of the menu).
Later you will be able to add wireless devices to the WLAN by pressing the WPS button of the router.
1. Select the PBC method in the software of the wireless device that you want to connect to the router's WLAN.
2. Click the relevant button in the software or press the WPS button on the cover of the wireless device that you want to connect to the WLAN.
3. Press the WPS button of the router and release. The WPS LED will start blinking.
Page 130 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
WMM
On the Wi-Fi / WMM page, you can enable the Wi-Fi Multimedia function.
The WMM function implements the QoS features for Wi-Fi networks. It helps to improve the quality of data transfer over Wi-Fi networks by prioritizing different types of traffic.
Select the needed action from the drop-down list in the Work mode section to configure the
WMM function:
• Auto : the settings of the WMM function are configured automatically (the value is specified by default).
• Manual : the settings of the WMM function are configured manually. When this value is selected, the Access Point and Station sections are displayed on the page.
• Disabled : the WMM function is disabled.
!
Figure 101. The page for configuring the WMM function.
All needed settings for the WMM function are specified in the device's system. Changing parameters manually may negatively affect your WLAN!
Page 131 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
The WMM function allows assigning priorities for four Access Categories (AC):
• BK ( Background ), low priority traffic (print jobs, file downloads, etc.).
• BE ( Best Effort ), traffic from legacy devices or devices/applications that do not support
QoS.
• VI ( Video ).
• VO ( Voice ).
Parameters of the Access Categories are defined for both the router itself (in the Access Point section) and wireless devices connected to it (in the Station section).
To edit the parameters of an Access Category, left-click the relevant line. In the opened window, change the needed parameters.
Figure 102. The window for changing parameters of the WMM function.
Parameter Description
AIFSN
CWMin/CWMax
Arbitrary Inter-Frame Space Number . This parameter influences time delays for the relevant Access Category. The lower the value, the higher is the Access Category priority.
Contention Window Minimum/Contention Window Maximum . Both fields influence time delays for the relevant Access Category. The
CWMax field value should not be lower, than the CWMin field value. The lower the difference between the CWMax field value and the CWMin field value, the higher is the Access Category priority.
Page 132 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Parameter
TXOP
ACM
ACK
Configuring via Web-based Interface
Description
Transmission Opportunity . The higher the value, the higher is the
Access Category priority.
Admission Control Mandatory .
If the switch is moved to the right, the device cannot use the relevant Access Category.
Acknowledgment . Answering response requests while transmitting.
Displayed only in the Access Point section.
If the switch is moved to the left, the router answers requests.
If the switch is moved to the right, the router does not answer requests.
Click the SAVE button.
Page 133 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Additional
On page of the Wi-Fi / Additional section, you can define additional parameters for the WLAN of the router.
!
Changing parameters presented on this page may negatively affect your WLAN!
Figure 103. Additional settings of the WLAN.
The following fields are available on the page:
Parameter
Bandwidth
Autonegotiation
20/40 (Coexistence)
TX power
Description
The channel bandwidth for 802.11n standard.
20MHz : 802.11n clients operate at 20MHz channels.
20/40MHz : 802.11n clients operate at 20MHz or 40MHz channels.
Move the switch to the right to let the router to automatically choose the most suitable channel bandwidth (20MHz or 40MHz) for the connected devices (this setting can substantially lower the data transfer rate of your wireless network).
The transmit power (in percentage terms) of the router.
Page 134 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Parameter Description
B/G protection
Short GI
Drop multicast
The 802.11b and 802.11g protection function is used to minimize collisions between devices of your wireless network.
Select a value from the drop-down list.
Auto : The protection function is enabled and disabled automatically depending on the state of the network (this value is recommended if your wireless local area network consists of both 802.11b and
802.11g devices).
Always On : The protection function is always enabled (this setting can substantially lower the efficiency of your wireless network).
Always Off : The protection function is always disabled.
Guard interval (in nanoseconds). This parameter defines the interval between symbols transmitted when the router is communicating to wireless devices.
Enable : the router uses the 400 ns short guard interval. Only for the wireless network operating modes which support 802.11n standard
(see the value of the Wireless mode drop-down list on the Wi-Fi /
Basic Settings page).
Disable : the router uses the 800 ns standard guard interval.
Move the switch to the right to disable multicasting for the router's
WLAN. Move the switch to the left to enable multicasting from the
WAN connection selected on the Advanced / IGMP page.
Beacon period
RTS threshold
Frag threshold
The time interval (in milliseconds) between packets sent to synchronize the wireless network.
The minimum size (in bytes) of a packet for which an RTS frame is transmitted.
The maximum size (in bytes) of a non-fragmented packet. Larger packets are fragmented (divided).
DTIM period
The time period (in beacon frames) between sending a DTIM (a message notifying on broadcast or multicast transmission) and data transmission.
Station Keep Alive
The time interval (in seconds) between keep alive checks of wireless devices from your WLAN. When the value 0 is specified, the checking is disabled.
When you have configured the parameters, click the APPLY button.
Page 135 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
MAC Filter
On the Wi-Fi / MAC Filter page, you can define a set of MAC addresses of devices which will be allowed to access the WLAN, or define MAC addresses of devices which will not be allowed to access the WLAN.
Figure 104. The page for configuring the MAC filter for the wireless network.
By default, MAC filtering is disabled.
To open the basic or additional wireless network for the devices which MAC addresses are specified on this page and to close the wireless network for all other devices, in the MAC Filter section, left-click the line of the wireless network. In the opened window, move the Enable MAC filter switch to the right. Upon that the MAC filter restrict mode drop-down list will be displayed. Select the Allow value from the drop-down list and click the SAVE button.
To close the wireless network for the devices which MAC addresses are specified on this page, select the Deny value from the MAC filter restrict mode drop-down list and click the SAVE button.
Click the ADD button to add a rule for MAC filtering.
Page 136 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Figure 105. The window for adding a rule for the MAC filter.
You can specify the following parameters:
Parameter Description
SSID
MAC address
Hostname
A wireless network to which the rule will be applied. Select the needed value from the drop-down list.
In the field, enter the MAC address to which the selected filtering mode will be applied.
The name of the device for easier identification. You can specify any name.
Enable
If the switch is moved to the right, the rule is active.
Move the switch to the left to disable the rule.
When you have configured the parameters, click the SAVE button.
To edit the parameters of the existing rule, in the Filters section, left-click the needed rule. In the opened window, change the settings and click the SAVE button.
To remove the rule from the page, in the Filters section, select the checkbox located to the left of the relevant rule and click the DELETE button.
Page 137 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Print Server
On the Print Server page, you can configure the router as a print server. Being configured in this way, the router will allow your LAN users to share the printer connected to the USB port of the router.
To connect a printer to the router, power off both devices. Connect the printer to the USB port of the router, power on the printer, then power on the router.
Figure 106. The Print Server page.
To configure the router as a print server, move the Enable print server switch to the right and click the APPLY button.
If you don't want to use the router as a print server, move the Enable print server switch to the left and click the APPLY button.
Page 138 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
USB Storage
This menu is designed to operate USB storages. Here you can do the following:
• view data on the connected USB storage
• create accounts for users to allow access to the content of the USB storage
• enable the built-in Samba server of the router
• enable the built-in FTP server of the router
• view content of the connected USB storage
• enable the built-in DLNA server of the router
• configure the built-in Transmission torrent client and manage distributing and downloading processes.
Information
On the USB Storage / Information page, you can view data on the USB storage connected to the router.
Figure 107. The USB Storage / Information page.
The following data are presented on the page: the name, total and free space of the storage, and the type of its file system (supported file systems: FAT16/32, NTFS, and ext2/3).
If the USB storage is divided into volumes, a section for every volume (partition) of the USB storage is displayed on the page.
To safely disconnect the USB storage or a volume of the USB storage, click the UNMOUNT button in the relevant section and wait for several seconds.
To disconnect all volumes of the USB storage, click the UNMOUNT ALL STORAGES button.
Page 139 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
USB Users
On the USB Storage / USB Users page, you can create user accounts to provide access to data on the USB storage connected to the router.
Figure 108. The USB Storage / USB Users page.
To create a new user account, click the ADD button.
Figure 109. The window for adding a user.
In the opened window, in the Login field, specify a username, and in the Password field – the password for the account. Use digits, Latin letters (uppercase and/or lowercase), and other characters available in the US keyboard layout.
12
!
You cannot create accounts with the following usernames: admin , support , user , nobody .
For ext2, ext3, or FAT storages or storage partitions, it is possible to create users with limited rights.
Move the Read only switch to the right not to let the user create, change, or delete files.
Click the SAVE button.
To change the password of an account, select the relevant line in the table. In the opened window, enter a new value in the Password field, and then click the SAVE button.
To remove an account, select the checkbox located to the left of the relevant line in the table and click the DELETE button.
12 0-9, A-Z, a-z, space, !"#$%&'()*+,-./:;<=>?@[\]^_`{|}~.
Page 140 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Samba
On the USB Storage / Samba page, you can enable the built-in Samba server of the router to provide access to the USB storage for users of your LAN.
Figure 110. The USB Storage / Samba page.
To enable the Samba server, move the Enable Samba server switch to the right.
The Anonymous login switch (by default, the switch is moved to the right) allows anonymous access to the content of the USB storage for users of your LAN.
If you want to provide authorized access to the content of the USB storage for users of your LAN, move the switch to the left. After applying the parameters on this page, go to the USB Storage /
USB Users page and create needed accounts.
In the Work group field, leave the value specified by default ( WORKGROUP ) or specify a new name of a workgroup which participants will have access to the content of the USB storage.
In the Short description field, you can specify an additional description for the USB storage.
This value will be displayed in some operating systems. Use digits and/or Latin characters.
In the NetBIOS field, specify a name of the USB storage which will be displayed for users of your
LAN. Use digits and/or Latin characters.
Page 141 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
To allow access only to a certain folder of the USB storage, click the ADD button in the
Directories section.
Figure 111. Specifying a folder.
In the opened window, locate a folder containing files. To do this, click the Search icon ( ) in the Path field. Then go to the needed folder and click the SELECT button.
In the Name field, specify a name of the selected folder which will be displayed for users of your
LAN. Use digits and/or Latin characters.
Click the SAVE button.
To remove a folder from the list in the Directories section, select the checkbox located to the left of the relevant line in the table and click the DELETE button.
After specifying the needed parameters, click the APPLY button.
To disable the built-in Samba server of the router, move the Enable Samba server switch to the left and click the APPLY button.
Page 142 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
FTP
On the USB Storage / FTP page, you can enable the built-in FTP server of the router to provide access to the USB storage for users of your LAN.
Figure 112. The USB Storage / FTP page.
To enable the FTP server, move the Enable FTP server switch to the right.
Move the Anonymous login switch to the right to allow anonymous access to the content of the
USB storage for users of your LAN. If you want to provide authorized access to the content of the
USB storage for users of your LAN, move the switch to the left . After applying the parameters on this page, go to the USB Storage / USB Users page and create needed accounts.
If needed, change the router's port used by the FTP server in the Port field (by default, the standard port 21 is specified).
To allow access only to a certain folder of the USB storage for users of your LAN, locate a folder containing files. To do this, click the Search icon ( ) in the Directory field. Then go to the needed folder and click the SELECT button.
After specifying the needed parameters, click the APPLY button.
To allow access to all the content of the USB storage for users of your LAN again, remove the value specified in the Directory field and click the APPLY button.
Page 143 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
To disable the built-in FTP server of the router, move the Enable FTP server switch to the left and click the APPLY button.
Page 144 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Filebrowser
On the USB Storage / Filebrowser page, you can view the content of your USB storage connected to the router and remove separate folders and files from the USB storage.
Figure 113. The USB Storage / Filebrowser page.
To view the content of the USB storage, click the icon of the storage or storage partition. The list of folders and files will be displayed on the page.
To go to a folder, click the line corresponding to this folder.
To refresh the folder contents, click the Actions icon ( ) in the line corresponding to this folder and select the Refresh value.
To remove a folder or file, click the Actions icon ( ) in the line corresponding to this folder or file and select the Remove value.
Page 145 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
DLNA
On the USB Storage / DLNA page, you can enable the built-in DLNA server of the router to provide access to the USB storage for users of your LAN.
The built-in media server allows DLNA certified devices of your LAN to play multimedia content of the USB storage. Multimedia content can be played only when a USB storage is connected to the router.
Figure 114. The USB Storage / DLNA page.
To enable the DLNA server, move the Enable switch to the right.
In the Update interval field, specify the time period (in seconds), at the end of which the media server updates the file list of the USB storage, or leave the value specified by default ( 900 ).
In the DLNA server name field, specify a name of the DLNA server which will be displayed for users of your LAN or leave the value specified by default ( D-Link DLNA Server ). Use digits and/or Latin characters.
To allow access to the content of the USB storage for users of your LAN, click the ADD button in the Media Folders section.
Page 146 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Figure 115. Specifying a media folder.
In the opened window, locate a folder containing files. To do this, click the Search icon ( ) in the Path field. Then go to the needed folder and click the SELECT button.
For each folder you can define the type of files which will be available for users of your LAN. To do this, select the needed type of files from the Type drop-down list. To share all files of a folder, select the All value from the Type drop-down list.
Click the SAVE button.
To remove a folder from the list in the Media Folders section, select the checkbox located to the left of the relevant line in the table and click the DELETE button.
After specifying all needed settings on the USB Storage / DLNA page, click the APPLY button.
To disable the built-in DLNA server of the router, move the Enable switch to the left and click the
APPLY button.
Page 147 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Torrent Client
On the USB Storage / Torrent Client page, you can configure all needed settings for the built-in
Transmission client.
Figure 116. The USB Storage / Torrent Client page.
You can specify the following parameters:
Parameter Description
Transmission
Enable
Port
Move the switch to the right to activate the Transmission client.
Main Settings
The router's port which will be used by the Transmission client.
Page 148 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Parameter
Path
Description
Locate data of the Transmission client. To do this, click the Search icon ( ), select the needed value, and click the SELECT button.
Directory
Enable download queue
Download queue size
Peer limit
Web interface port
The folder on the USB storage where data of the Transmission client will be stored.
Move the switch to the right if you want to limit the number of simultaneous downloads. Upon that the Download queue size field will be displayed.
Move the switch to the left not to limit the number of simultaneous downloads.
The maximum number of simultaneous downloads. By default, the value 1 is specified.
The maximum number of the service users from which you can download files.
The port on which the web-based interface of the Transmission client is available.
Authorization
Enable
Move the switch to the right if you want the Transmission client to request for username and password when accessing its web-based interface. Then fill in the Username and Password fields.
Username
The username to access the web-based interface of the Transmission client.
Password
The password to access the web-based interface of the Transmission client. Click the Show icon ( ) to display the entered password.
After specifying the needed parameters, click the APPLY button.
In the Web-interface page field, the address of the web-based interface of the Transmission client is displayed. To access the web-based interface of the Transmission client, click the link.
Page 149 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Figure 117. The web-based interface of the Transmission torrent client.
Using the web-based interface of the built-in Transmission torrent client you can manage the process of downloading files to the USB storage connected to the router.
The following buttons are available on the page:
Parameter
Open Torrent
Description
Click the button to add a new torrent file (a metadata file according to which the Transmission client downloads files) to the download queue. In the dialog box appeared, select a file stored on your PC and click the Upload button.
Remove Selected
Torrents
Select the torrent file which you want to remove from the download queue and click the button.
Start Selected
Torrents
Select the torrent file corresponding to the download which should be restarted and click the button.
Page 150 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Parameter
Start All Torrents
Configuring via Web-based Interface
Description
Click the button to restart all downloads. If you limited the maximum number of simultaneous downloads, the Transmission client starts processing of the specified number of torrent files; after completing download of the first one, the client proceeds to the next file in the queue.
Pause Selected
Torrents
Select the torrent file corresponding to the download which should be stopped and click the button.
Click the button to stop all downloads.
Pause All Torrents
Select a torrent file and click the button to view its data.
Toggle Inspector
Page 151 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
USB Modem
This menu is designed to operate USB modems.
If the PIN code check for the SIM card inserted into your USB modem is not disabled, the relevant notification will be displayed in the top right corner of the page.
Figure 118. The notification on the PIN code check.
Click the ENTER button. When the USB Modem / PIN page opens, enter the PIN code in the
Authorization section 13 . Click the Show icon ( ) to display the entered code. Then click the
APPLY button.
Figure 119. Entering the PIN code.
Some USB modems in the router mode and Android smartphones in the modem mode have an IP address from the subnet which coincides with the router's local subnet. In this case, the router's web-based interface can be unavailable. For correct operation, disconnect the device from the USB port and reboot the router. Then access the web-based interface, go to the Connections Setup /
LAN page, and change the value of the IP address field on the IPv4 tab (for example, specify the value 192.168.2.1
). Wait until the router is rebooted.
13 For some models of USB modems it is required to disable the PIN code check on the SIM card prior to connecting the USB modem to the router.
Page 152 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Basic Settings
On the USB Modem / Basic Settings page, you can view data on the USB modem connected to the router and enable/disable the function for automatic creation of 3G/LTE WAN connection upon plugging a USB modem into the router.
Figure 120. The USB Modem / Basic Settings page.
If the Automatic creation of connection switch is moved to the right and the PIN code check for the SIM card inserted into your USB modem is disabled, then an active WAN connection with default settings (for LTE modems) or the operator's settings (for GSM modems) will be automatically created when plugging the USB modem into the router. The connection will be displayed on the Connections Setup / WAN page.
If you don't want to use this function, move the Automatic creation of connection switch to the right and click the APPLY button.
When a USB modem is connected to the router, the following data are displayed in the
Information section:
Parameter Description
Vendor
Model
The manufacturer of your USB modem.
The alphanumeric code of the model of your USB modem.
Revision
IMSI
IMEI
The revision of the firmware of your USB modem.
The code stored in the SIM card inserted to your USB modem.
The code stored in the memory of the USB modem.
Page 153 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Parameter
Signal level
Operator name
Description
The signal level at the input of the modem's receiver. The zero signal level shows that you are out of the coverage area of the selected operator's network.
When the needed network is available, the name of the operator is displayed in this field.
A type of the network to which the USB modem is connected.
Mode
PIN
On the USB Modem / PIN page, you can change the PIN code of the SIM card inserted into your
USB modem, disable or enable the check of the PIN code.
!
The operations presented on this page are unavailable for some models of USB modems.
The current state of the SIM card inserted into your USB modem is displayed in the Status field. If the PIN code is entered incorrectly or the PIN code is not entered when the PIN code check is enabled, the Device is locked value is displayed in the Status field. If the PIN code is entered correctly or the PIN check is disabled, the Device is unlocked value is displayed in the Status field.
If the PIN code check for the SIM card inserted into your USB modem is not disabled, the Yes value is displayed in the PIN code request field. If the PIN check is disabled, the No value is displayed in the PIN code request field.
Figure 121. The USB Modem / PIN page.
Page 154 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
To disable the PIN code check, in the PIN Code Request section, enter the current PIN code in the PIN code field and click the DISABLE button (the button is displayed if the PIN code check is enabled).
To enable the PIN code check, in the PIN Code Request section, enter the PIN code used before disabling the check in the PIN code field and click the ENABLE button (the button is displayed if the PIN code check is disabled).
To change the PIN code, in the Changing PIN Code section, enter the current code in the PIN code field, then enter a new code in the New PIN code and New PIN code confirmation fields and click the SAVE button.
If upon one of the operations described above you have entered an incorrect value in the PIN code field three times (the number of remaining attempts is displayed on the page), the SIM card inserted into your USB modem is blocked.
Figure 122. The USB Modem / PIN page. The PUK code request.
For further use of the card, in the Authorization section, enter the PUK code in the relevant field, and then specify a new PIN code for your SIM card in the New PIN code and New PIN code confirmation field. Click the APPLY button.
Page 155 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Advanced
In this menu you can configure advanced settings of the router:
• define interface groups
• allow the router to connect to a private Ethernet line
• add name servers
• configure a DDNS service
• define static routes
• configure TR-069 client
• create rules for remote access to the web-based interface
• enable the UPnP IGD protocol
• edit the ADSL connection parameters
• allow the router to use IGMP
• allow the router to use RTSP, enable the SIP ALG, the PPPoE/PPTP/L2TP/IPsec pass through functions for the router.
Page 156 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Interface Grouping
On the Advanced / Interface Grouping page, you can create groups consisting of interfaces and ports of the router, for example, for distinguishing different types of traffic. Such a function is mostly used in Triple-play networks.
The DEFAULT group is created in the router's system. You cannot edit or delete this group.
Figure 123. The Advanced / Interface Grouping page.
To create a new rule for interface grouping (a group of ports), click the ADD button.
Figure 124. The page for adding a new group of ports.
Page 157 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
On the opened page, you can specify the following parameters:
Parameter Description
Name
A name for the group for easier identification. You can specify any name.
Type of group
LAN Ports
The type of the group.
NAT . The group of this type is an external connection with address translation. It is mostly used to connect to the Internet.
Transparent bridge . The group of this type is a transparent connection between the router's port and an external connection. It is mostly used to connect IPTV set-top boxes.
Local . The group of this type is an internal connection of the router's ports. It is mostly used to join devices from the LAN to an isolated network with no access to the Internet.
In this section the LAN ports and the WLAN interface of the router are displayed.
To add an element to the group, select the relevant checkbox.
To remove an element from the group, deselect the relevant checkbox.
Displayed for the NAT and Transparent bridge types only.
In this section WAN connections of the router are displayed.
WAN Interfaces
To add a connection to the group, select the choice of the radio button which corresponds to this connection.
Click the APPLY button.
To edit the parameters of a group you created, select the relevant line in the table. On the opened page, change the needed parameters and click the APPLY button.
To remove a group you created, select the checkbox located to the left of the relevant line of the table and click the DELETE button. Also you can remove a group on the editing page. When you delete a group, ports and interfaces assigned to it are reassigned to the DEFAULT group.
Page 158 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
WAN Remapping
On the Advanced / WAN Remapping page, you can configure the router to connect to a private
Ethernet line.
!
The Ethernet WAN function allows using any Ethernet port of the router to access the
Internet via Ethernet technology. When the function is enabled, the router is still able to access the Internet via ADSL technology.
Figure 125. The Advanced / WAN Remapping page.
To use one of the router's LAN port as the WAN port, click the icon corresponding to this port and click the APPLY button. Port configured as the WAN port is highlighted in teal.
If in the future you need to disconnect the LAN port from the private Ethernet line, click the icon highlighted in teal and click the APPLY button.
Page 159 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
DNS
On the Advanced / DNS page, you can add DNS servers to the system.
Figure 126. The Advanced / DNS page.
DNS servers are used to determine the IP address from the name of a server in Intranets or the
Internet (as a rule, they are specified by an ISP or assigned by a network administrator).
You can specify the addresses of DNS servers manually on this page or configure the router to obtain DNS servers addresses automatically from your ISP upon installing a connection.
!
When you use the built-in DHCP server, the network parameters (including DNS servers) are distributed to clients automatically.
If you want to configure automatic obtainment of DNS servers addresses, move the Manual switch to the left (use the DNS IPv4 section for IPv4 and the DNS IPv6 section for IPv6). Then move the
Default gateway switch to the left and from the Interface drop-down list select a WAN connection which will be used to obtain addresses of DNS servers automatically. If you want the router to use the default WAN connection to obtain addresses of DNS servers, move the Default gateway switch to the right. Then click the APPLY button.
To specify a DNS server manually, move the Manual switch to the right (use the DNS IPv4 section for IPv4 and the DNS IPv6 section for IPv6). In the Name Servers IPv4 or Name
Servers IPv6 section, click the ADD SERVER button, and in the line displayed, enter an IP address of the DNS server. Then click the APPLY button.
To remove a DNS server from the page, click the Delete icon ( ) in the line of the address and then click the APPLY button.
If needed, you can add your own address resource record. To do this, click the ADD button.
Page 160 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Figure 127. The window for adding a DNS record.
In the IP address field, specify a host from the internal or external network. You can choose a device connected to the router's LAN at the moment. To do this, select the relevant IP address from the drop-down list (the field will be filled in automatically). In the Name field, specify the domain name to which the specified IP address will correspond. Click the SAVE button.
To edit an existing record, select the relevant line in the table. In the opened window, change the needed parameters and click the SAVE button.
To remove a record, select the checkbox located to the left of the relevant line in the table and click the DELETE button.
After completing the work with records, click the APPLY button.
Page 161 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
DDNS
On the Advanced / DDNS page, you can define parameters of the DDNS service, which allows associating a domain name with dynamic IP addresses.
Figure 128. The Advanced / DDNS page.
To add a new DDNS service, click the ADD button.
Figure 129. The window for adding a DDNS service.
Page 162 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
In the opened window, you can specify the following parameters:
Parameter Description
Host name The full domain name registered at your DDNS provider.
DDNS service
Username
Select a DDNS provider from the drop-down list.
The username to authorize for your DDNS provider.
Password
The password to authorize for your DDNS provider. Click the
Show icon ( ) to display the entered password.
Update period
An interval (in minutes) between sending data on the router's external IP address to the relevant DDNS service.
After specifying the needed parameters, click the SAVE button.
To edit parameters of the existing DDNS service, select the relevant line in the table. In the opened window, change the needed parameters and click the SAVE button.
To remove an existing DDNS service, select the checkbox located to the left of the relevant line in the table and click the DELETE button.
Page 163 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Routing
On the Advanced / Routing page, you can add static routes (routes for networks that are not connected directly to the device but are available through the interfaces of the device) into the system.
Figure 130. The Advanced / Routing page.
To create a new route, click the ADD button.
Figure 131. The window for adding a new route.
Page 164 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
In the opened window, you can specify the following parameters:
Parameter Description
Protocol A protocol that the route will use.
Interface
Destination network
Destination netmask
From the drop-down list, select an interface through which the destination network can be accessed. If you have selected the Auto value, the router itself sets the interface on the basis of data on connected networks.
A destination network to which this route is assigned. You can specify an IPv4 or IPv6 address.
You can specify an IPv6 address ( 2001:db8:1234::1 ) or an IPv6 address with a prefix ( 2001:db8:1234::/64 ).
For IPv4 protocol only.
The destination network mask.
An IP address through which the destination network can be accessed.
Gateway
Metric
A metric for the route. The lower the value, the higher is the route priority. Optional .
After specifying the needed parameters, click the SAVE button.
To edit an existing route, select a relevant line of the table. On the opened page, change the needed parameters and click the SAVE button.
To remove an existing route, select the checkbox located to the left of the relevant line in the table and click the DELETE button.
Page 165 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
TR-069 Client
On the Advanced / TR-069 Client page, you can configure the router for communication with a remote Auto Configuration Server (ACS).
The TR-069 client is used for remote monitoring and management of the device.
Figure 132. The page for configuring the TR-069 client.
You can specify the following parameters:
Parameter Description
TR-069 Client
Interface
The interface which the router uses for communication with the
ACS. Leave the Automatic value to let the device select the interface basing on the routing table or select another value if required by your ISP.
Enable TR-069 client Move the switch to the right to enable the TR-069 client.
Page 166 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Parameter Description
Enable
Interval
Inform settings
Move the switch to the right so the router may send reports (data on the device and network statistics) to the ACS.
Specify the time period (in seconds) between sending reports.
Auto Configuration Server Settings
The URL address of the ACS provided by the ISP.
The username to connect to the ACS.
URL address
Username
Password
Username
Password
Request port
The password to connect to the ACS. Click the Show icon ( ) to display the entered password.
Connection Request Settings
The username used by the ACS to transfer a connection request to the router.
The password used by the ACS. Click the Show icon ( ) to display the entered password.
The port used by the ACS. By default, the port 8999 is specified.
Request path The path used by the ACS.
When you have configured the parameters, click the APPLY button.
Page 167 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Remote Access
On the Advanced / Remote Access page, you can configure access to the web-based interface of the router. By default, the access from external networks to the router is closed. If you need to allow access to the router from the external network, create relevant rules.
Figure 133. The Advanced / Remote Access page.
To create a new rule, click the ADD button.
Figure 134. The window for adding a rule for remote management.
Page 168 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
In the opened window, you can specify the following parameters:
Parameter Description
Name
Interface
IP version 14
A name for the rule for easier identification. You can specify any name.
Select a WAN connection to which this rule will be assigned. When the Automatic value is selected, the router uses the default connection.
An IP version to which the rule will be applied. Select the relevant value from the drop-down list.
Open access from any external host
IP address
Mask
Move the switch to the right to allow access to the router for any host. Upon that the IP address and Mask fields are not displayed.
A host or a subnet to which the rule is applied. You can specify an
IPv4 or IPv6 address.
For the IPv4-based network only.
The mask of the subnet.
Public port
For the IPv4-based network only.
An external port of the router. You can specify only one port.
Protocol The protocol available for remote management of the router.
After specifying the needed parameters, click the SAVE button.
To edit a rule for remote access, left-click the relevant rule. In the opened window, change the needed parameters and click the SAVE button.
To remove a rule for remote access, select the checkbox located to the left of the relevant line in the table and click the DELETE button.
14 Remote access via IPv6 will be implemented in further versions of the firmware.
Page 169 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
UPnP IGD
On the Advanced / UPnP IGD page, you can enable the UPnP IGD protocol. The router uses the
UPnP IGD protocol for automatic configuration of its parameters for network applications requiring an incoming connection to the router.
Figure 135. The Advanced / UPnP IGD page.
If you want to manually specify all parameters needed for network applications, move the Enable switch to the left. Then go to the Firewall / Virtual Servers page and specify needed settings.
If you want to enable the UPnP IGD protocol in the router, move the Enable switch to the right.
When the protocol is enabled, the router's parameters configured automatically are displayed on the page:
Parameter Description
Protocol A protocol for network packet transmission.
IP
Private port
Public port
Description
The IP address of a client from the local area network.
A port of a client's IP address to which traffic is directed from a public port of the router.
A public port of the router from which traffic is directed to a client's
IP address.
Information transmitted by a client's network application.
Page 170 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
xDSL
The Advanced / xDSL page includes the set of ADSL standards that should be defined by an ISP.
Contact your ISP to set proper parameters. Select the relevant options and click the APPLY button.
Figure 136. The Advanced / xDSL page.
Page 171 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
IGMP
On the Advanced / IGMP page, you can allow the router to use IGMP.
IGMP is used for managing multicast traffic (transferring data to a group of destinations). This protocol allows using network resources for some applications, e.g., for streaming video, more efficiently.
Figure 137. The Advanced / IGMP page.
The following elements are available on the page:
Parameter Description
Enable Move the switch to the right to enable IGMP.
IGMP version Select a version of IGMP from the drop-down list.
Interface
From the drop-down list, select a connection of the Dynamic IPv4 or
Static IPv4 type for which you need to allow multicast traffic (e.g.
streaming video).
IGMP Snooping
The IGMP snooping function allows limiting multicast traffic for devices connected to the Ethernet ports of the router.
If the switch is moved to the right, multicast traffic is forwarded only to the devices which require it.
If the switch is moved to the left, multicast traffic is forwarded to all devices connected to the Ethernet ports of the router.
After specifying the needed parameters, click the APPLY button.
Page 172 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
ALG/Passthrough
On the Advanced / ALG/Passthrough page, you can allow the router to use RTSP, enable the
SIP ALG and PPPoE/PPTP/L2TP/IPsec pass through functions.
SIP is used for creating, modifying, and terminating communication sessions. This protocol allows telephone calls via the Internet.
RTSP is used for real-time streaming multimedia data delivery. This protocol allows some applications to receive streaming audio/video from the Internet.
The PPPoE pass through function allows PPPoE clients of computers from your LAN to connect to the Internet through connections of the router.
The PPTP pass through, L2TP pass through and IPsec pass through functions allow VPN PPTP,
L2TP and IPsec traffic to pass through the router so that clients from your LAN can establish relevant connections with remote networks.
Figure 138. The Advanced / ALG/Passthrough page.
Page 173 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
The following elements are available on the page:
Parameter Description
SIP
RTSP
PPPoE pass through
Move the switch to the right to enable SIP. Such a setting allows using the SIP ALG function. This function allows VoIP traffic to pass through the NAT-enabled router.
15
Move the switch to the right to enable RTSP. Such a setting allows managing media stream: fast forward streaming audio/video, pause and start it.
Move the switch to the right to enable the PPPoE pass through function.
IPsec pass through
L2TP pass through
Move the switch to the right to enable the IPsec pass through function.
Move the switch to the right to enable the L2TP pass through function.
PPTP pass through
Move the switch to the right to enable the PPTP pass through function.
After specifying the needed parameters, click the APPLY button.
15 On the Connections Setup / WAN page, create a WAN connection, move the SIP switch to the right on the
Advanced / ALG/Passthrough page, connect an Ethernet cable between a LAN port of the router and the IP phone. Specify SIP parameters on the IP phone and configure it to obtain an IP address automatically (as DHCP client).
Page 174 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Firewall
In this menu you can configure the firewall of the router:
• add rules for IP filtering
• create virtual servers
• define a DMZ
• configure the MAC filter
• specify restrictions on access to certain web sites.
IP Filter
On the Firewall / IP Filter page, you can create new rules for filtering IP packets and edit or remove existing rules.
Figure 139. The Firewall / IP Filter page.
To create a new rule, click the ADD button.
Page 175 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Figure 140. The page for adding a rule for IP filtering.
You can specify the following parameters:
Parameter Description
Enable rule
Name
Action
General Settings
Move the switch to the right to enable the rule.
Move the switch to the left to disable the rule.
A name for the rule for easier identification. You can specify any name.
Select an action for the rule.
Allow : Allows packet transmission in accordance with the criteria specified by the rule.
Deny : Denies packet transmission in accordance with the criteria specified by the rule.
Page 176 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Parameter
Protocol
IP version
Description
A protocol for network packet transmission. Select a value from the drop-down list.
An IP version to which the rule will be applied. Select the relevant value from the drop-down list.
Source IP Address
Set as
Start IPv4 address /
Start IPv6 address
Select the needed value from the drop-down list.
The source host start IPv4 or IPv6 address.
If it is necessary to specify a single address, leave the End IPv4 address / End IPv6 address field blank.
You can choose a device connected to the router's LAN at the moment. To do this, select the relevant IPv4 or IPv6 address from the drop-down list (the field will be filled in automatically).
End IPv4 address /
End IPv6 address
Subnet IPv4 address /
Subnet IPv6 address
Set as
Start IPv4 address /
Start IPv6 address
The source host end IPv4 or IPv6 address.
The source subnet IPv4 or IPv6 address. The field is displayed when the Subnet value is selected from the Set as drop-down list.
Destination IP Address
Select the needed value from the drop-down list.
The destination host start IPv4 or IPv6 address.
If it is necessary to specify a single address, leave the End IPv4 address / End IPv6 address field blank.
You can choose a device connected to the router's LAN at the moment. To do this, select the relevant IPv4 or IPv6 address from the drop-down list (the field will be filled in automatically).
End IPv4 address /
End IPv6 address
Subnet IPv4 address /
Subnet IPv6 address
Destination port
The destination host end IPv4 or IPv6 address.
The destination subnet IPv4 or IPv6 address. The field is displayed when the Subnet value is selected from the
Ports
Set as drop-down list.
A port of the destination IP address. You can specify one port, several ports separated by a comma, or a range of ports separated by a colon.
Page 177 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Parameter Description
Set source port manually
Move the switch to the right to specify a port of the source IP address manually. Upon that the Source port field is displayed.
Source port
A port of the source IP address. You can specify one port, several ports separated by a comma, or a range of ports separated by a colon.
Click the APPLY button.
To edit a rule for IP filtering, select the relevant line in the table. On the opened page, change the needed parameters and click the APPLY button.
To remove a rule, select the checkbox located to the left of the relevant line of the table and click the DELETE button. Also you can remove a rule on the editing page.
Page 178 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Virtual Servers
On the Firewall / Virtual Servers page, you can create virtual servers for redirecting incoming
Internet traffic to a specified IP address in the local area network.
Figure 141. The Firewall / Virtual Servers page.
To create a new virtual server, click the ADD button.
Figure 142. The page for adding a virtual server.
Page 179 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
You can specify the following parameters:
Parameter
Name
Template
Interface
Protocol
NAT Loopback
Remote IP
Public port (begin)/
Public port (end)
Private IP
Description
General Settings
A name for the virtual server for easier identification. You can specify any name.
Select a virtual server template from the drop-down list, or select
Custom to specify all parameters of the new virtual server manually.
A WAN connection to which this virtual server will be assigned.
A protocol that will be used by the new virtual server. Select a value from the drop-down list.
Move the switch to the right in order to let the users of the router's
LAN access the local server using the external IP address of the router or its DDNS name (if a DDNS service is configured). Users from the external network access the router using the same address
(or DDNS name).
Public Network Settings
Enter the IP address of the server from the external network.
To add one more IP address, click the ADD REMOTE IP button and enter the address in the displayed line.
To remove the IP address, click the Delete icon ( ) in the line of the address.
A port of the router from which traffic is directed to the IP address specified in the Private IP field in the Private Network Settings section. Specify the start and the end value for the port range. If you need to specify one port, enter the needed value in the Public port
(begin) field and leave the Public port (end) field blank.
Private Network Settings
The IP address of the server from the local area network. To choose a device connected to the router's LAN at the moment, select the relevant value from the drop-down list (the field will be filled in automatically).
Page 180 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Parameter Description
Private port (start)/
Private port (end)
A port of the IP address specified in the Private IP field to which traffic is directed from the Public port . Specify the start and the end value for the port range. If you need to specify one port, enter the needed value in the Private port (start) field and leave the
Private port (end) field blank.
Click the APPLY button.
To edit the parameters of an existing server, select the relevant line in the table. On the opened page, change the needed parameters and click the APPLY button.
To remove a server, select the checkbox located to the left of the relevant line of the table and click the DELETE button. Also you can remove a server on the editing page.
Page 181 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
DMZ
A DMZ is a host or network segment located “between” internal (local) and external (global) networks. In the router, the DMZ implements the capability to transfer a request coming to a port of the router from the external network to a specified host of the internal network.
On the Firewall / DMZ page, you can specify the IP address of the DMZ host.
Figure 143. The Firewall / DMZ page.
To enable the DMZ, move the Enable switch to the right.
Enter the IP address of a host from your network in the IP address field. To choose a device connected to the router's LAN at the moment, select the relevant value from the drop-down list (the field will be filled in automatically).
Click the APPLY button.
Note that when the DMZ is enabled, all traffic coming to a port of the WAN interface of the router is directed to the same port of the specified IP address. Also note that virtual servers have higher priority than the DMZ host. In other words, if there has been created a virtual server that directs traffic from external port 80 to a port of the device from the router's local network, then entering http://router_WAN_IP in the address bar, users of the external network are directed to the specified port and IP address configured for the virtual server, but not to port 80 of the device with the IP address specified on the Firewall / DMZ page.
To disable the DMZ, move the Enable switch to the left and click the APPLY button.
Page 182 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
MAC Filter
On the Firewall / MAC Filter page, you can configure MAC-address-based filtering for computers of the router's LAN.
Figure 144. The Firewall / MAC Filter page.
Select the needed action from the drop-down list in the Default mode section to configure filtering for all devices of the router's network:
• Allow : Allows access to the router's network and to the Internet for devices (the value is specified by default);
• Deny : Blocks access to the router's network for devices.
If you need to specify a filtering mode for each device separately, create a relevant rule. To do this, click the ADD button.
Figure 145. The window for adding a rule for the MAC filter.
Page 183 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
In the opened window, you can specify the following parameters:
Parameter Description
Enable rule
Action
Move the switch to the right to enable the rule.
Move the switch to the left to disable the rule.
Select an action for the rule.
Deny : Blocks access to the router's network for the device with the specified MAC address.
Allow : Allows access to the router's network and to the Internet for the device with the specified MAC address when the rules on the
Firewall / IP Filter page block access for this device.
MAC address
The MAC address of a device from the router's LAN. You can enter the MAC address of a device connected to the router's LAN at the moment. To do this, select the relevant device from the drop-down list (the field will be filled in automatically).
After specifying the needed parameters, click the SAVE button.
To edit a rule, select the relevant line in the table. In the opened window, change the needed parameters and click the SAVE button.
To remove a rule, select the checkbox located to the left of the relevant line of the table and click the DELETE button. Also you can remove a rule in the editing window.
Page 184 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
URL Filter
On the Firewall / URL Filter page, you can specify restrictions on access to certain web sites.
Figure 146. The Firewall / URL Filter page.
To enable the URL filter, in the General Settings section, move the Enable switch to the right, then select the needed mode from the Type drop-down list:
• Block listed URLs : when this value is selected, the router blocks access to all addresses specified in the Filters section;
• Block all URLs except listed : when this value is selected, the router allows access to addresses specified in the Filters section and blocks access to all other web sites.
Click the APPLY button.
To specify URL addresses to which the selected filtering mode will be applied, in the Filters section, click the ADD RULE button and enter a relevant address in the displayed line. Then click the APPLY button.
To remove an address from the list of URL addresses, click the Delete icon ( ) in the line of the relevant URL address. Then click the APPLY button.
Page 185 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
System
In this menu you can do the following:
• change the password used to access the router's settings
• restore the factory default settings
• create a backup of the router's configuration
• restore the router's configuration from a previously saved file
• save the current settings to the non-volatile memory
• reboot the router
• change the web-based interface language
• update the firmware of the router
• configure automatic notification on new firmware version
• view the system log; configure sending the system log to a remote host and/or a USB storage connected to the router
• check availability of a host on the Internet through the web-based interface of the router
• trace the route to a host
• allow or forbid access to the router via TELNET
• configure automatic synchronization of the system time or manually configure the date and time for the router.
Page 186 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Configuration
On the System / Configuration page, you can change the password for the administrator account used to access the web-based interface of the router and to access the device settings via TELNET, restore the factory defaults, backup the current configuration, restore the router's configuration from a previously created file, save the changed settings to the non-volatile memory, reboot the device, or change the web-based interface language.
Figure 147. The System / Configuration page.
In order to change the password for the administrator account, in the User section, enter a new password in the Password and Password confirmation fields. Click the Show icon ( ) to display the entered password. Use digits, Latin letters (uppercase and/or lowercase), and other characters available in the US keyboard layout.
16 Then click the SAVE button.
!
Remember or write down the new password for the administrator account. In case of losing the new password, you can access the settings of the router only after restoring the factory default settings via the hardware RESET button. This procedure wipes out all settings that you have configured for your router.
To change the web-based interface language, select the needed value from the Language dropdown list.
16 0-9, A-Z, a-z, space, !"#$%&'()*+,-./:;<=>?@[\]^_`{|}~.
Page 187 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
The following buttons are also available on the page:
Control
Factory
Description
Click the button to restore the factory default settings. Also you can restore the factory defaults via the hardware RESET button (see the
Back and Bottom Panels section, page 13).
Backup
Restore
Save
Click the button to save the configuration (all settings of the router) to your PC. The configuration backup will be stored in the download location of your web browser.
Click the button and follow the dialog box appeared to select a previously saved configuration file (all settings of the router) located on your PC and upload it.
Click button to save settings to the non-volatile memory.
The router saves changed settings automatically. If changed settings have not been saved automatically, a notification is displayed in the top right part of the page.
Reboot
Click the button to reboot the device. All unsaved changes will be lost after the device's reboot.
Page 188 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Firmware Update
On the System / Firmware Update page, you can update the firmware of the router and configure the automatic check for updates of the router's firmware.
!
Update the firmware only when the router is connected to your PC via a wired connection.
Figure 148. The System / Firmware Update page.
The current version of the router's firmware is displayed in the Current firmware version field.
By default, the automatic check for the router's firmware updates is enabled. If a firmware update is available, a notification will be displayed in the top right corner of the page.
To disable the automatic check for firmware updates, in the Remote update section, move the
Check for updates automatically switch to the left and click the APPLY SETTINGS button.
To enable the automatic check for firmware updates, in the Remote update section, move the
Check for updates automatically switch to the right and click the APPLY SETTINGS button.
By default, in the Remote server URL field, the D-Link update server address
( fwupdate.dlink.ru
) is specified.
You can update the firmware of the router locally (from the hard drive of your PC) or remotely
(from the update server).
Page 189 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Local Update
!
Attention! Do not turn off the router before the firmware update is completed. This may cause the device breakdown.
To update the firmware of the router locally, follow the next steps:
1. Download a new version of the firmware from www.dlink.ru
.
2. Click the CHOOSE FILE button in the Local Update section on the System /
Firmware Update page to locate the new firmware file.
3. Click the UPDATE FIRMWARE button.
4. Wait until the router is rebooted (about one and a half or two minutes).
5. Log into the web-based interface using the login ( admin ) and the current password.
If after updating the firmware the router doesn't work correctly, please restore the factory default settings. To do this, click the Factory button on the System / Configuration page. Wait until the router is rebooted.
Page 190 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Remote Update
!
Attention! Do not turn off the router before the firmware update is completed. This may cause the device breakdown.
To update the firmware of the router remotely, follow the next steps:
1. On the System / Firmware Update page, in the Remote Update section, click the
CHECK FOR UPDATES button to check if a newer firmware version exists.
2. Click the UPDATE FIRMWARE button (the button is displayed if a newer version of the firmware is available).
3. Wait until the router is rebooted (about one and a half or two minutes).
4. Log into the web-based interface using the login ( admin ) and the current password.
If after updating the firmware the router doesn't work correctly, please restore the factory default settings. To do this, click the Factory button on the System / Configuration page. Wait until the router is rebooted.
Page 191 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Log
On the System / Log page, you can set the system log options and configure sending the system log to a remote host and/or a USB storage 17 connected to the router.
Figure 149. The System / Log page. The Settings tab.
To enable logging of the system events, go to the Settings tab and move the Enable switch to the right. Then specify the needed parameters.
17 This function will be implemented in further versions of the firmware.
Page 192 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Parameter Description
Type
Level
Server
Port
USB Storage
Save log to a USB storage
Logging
Select a type of logging from the drop-down list.
• Local : the system log is stored in the router's memory. When this value is selected, the Server and Port fields are not displayed.
• Remote : the system log is sent to the remote host specified in the Server field.
• Local and remote : the system log is stored in the router's memory and sent to the remote host specified in the Server field.
Select a type of messages and alerts/notifications to be logged.
The IP or URL address of the host from the local or global network, to which the system log will be sent.
A port of the host specified in the Server field. By default, the value
514 is specified.
Record to USB
If a USB storage is connected to the router, its name is displayed in the field.
To safely disconnect the USB storage, click the UNMOUNT button.
Move the switch to the right so that the device could send the system log to the USB storage connected to it. Upon that the Path , The maximum size of one file , File name , and Number of files to keep fields are displayed.
Path
Click the Search icon ( ) located to the right of the field in order to locate the folder where system log files will be stored.
The maximum size of one file
File name
The maximum size (in kilobytes) of one system log file.
A name for system log files.
Number of files to keep
The maximum number of files allowed to be recorded on the USB storage. When this number is exceeded, the file containing the oldest data will be deleted. The field is available for editing if the value specified in the The maximum size of one file field is greater than zero.
After specifying the needed parameters, click the APPLY button.
Page 193 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
To disable logging of the system events, move the Enable switch to the left and click the APPLY button.
To view the system log, go to the Log tab.
Figure 150. The System / Log page. The Log tab.
To view the latest system events, click the REFRESH button.
To save the system log to your PC, click the EXPORT button. The file will be stored in the download location of your web browser.
Page 194 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Ping
On the System / Ping page, you can check availability of a host from the local or global network via the Ping utility.
The Ping utility sends echo requests to a specified host and receives echo replies.
Figure 151. The System / Ping page.
To check availability of a host, enter the IP address or name of this host in the Host field and specify a number of requests that will be sent in order to check its availability in the Count of packets field. If availability check should be performed with IPv6, move the IPv6 switch to the right.
To specify additional settings, click the MORE SETTINGS button.
Figure 152. The System / Ping page. The additional settings window.
Page 195 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
In the opened window, in the Packet size field, specify the volume of data sent in a request. In the
Time to wait for a response field, specify the response waiting period in seconds. To restore the default field values, click the DEFAULT SETTINGS button.
After specifying the additional parameters, click the OK button.
To run the check, click the START button. After a while, the results will be displayed on the page.
To remove the check result from the page, click the CLEAR button.
Page 196 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Traceroute
On the System / Traceroute page, you can determine the route of data transfer to a host via the traceroute utility.
Figure 153. The System / Traceroute page.
To determine the route, enter the name or IP address of a host in the Host field. If the route should be determined using IPv6, move the IPv6 switch to the right.
To specify additional settings, click the MORE SETTINGS button.
Page 197 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Figure 154. The System / Traceroute page. The additional settings window.
In the opened window, you can specify the following parameters:
Parameter Description
Maximum TTL value
Number of probes
Specify the TTL ( Time to live ) parameter value. The default value is
30 .
The number of attempts to hit an intermediate host.
Wait time A period of waiting for an intermediate host response.
To restore the default field values, click the DEFAULT SETTINGS button.
After specifying the additional parameters, click the OK button.
To run the check, click the START button. After a while, the results will be displayed on the page.
To remove the check result from the page, click the CLEAR button.
Page 198 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Telnet
On the System / Telnet page, you can enable or disable access to the device settings via TELNET from your LAN. Access via TELNET is disabled by default. It is automatically enabled after changing the default administrator password.
Figure 155. The System / Telnet page.
To disable access via TELNET, move the Enable Telnet switch to the left and click the APPLY button.
To enable access via TELNET again, move the Enable Telnet switch to the right. In the Port field, enter the number of the router's port through which access will be allowed (by default, the port 23 is specified). Then click the APPLY button.
Page 199 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
System Time
On the System / System Time page, you can manually set the time and date of the router or configure automatic synchronization of the system time with a time server on the Internet.
Figure 156. The System / System Time page.
To set the system time manually, follow the next steps:
1. Move the Enable NTP switch to the left.
2. In the Time Settings section, specify needed values. To specify the time set up your PC or portable device, click the SET LOCAL TIME button.
3. Click the APPLY button. The System date and System time fields will be filled in automatically.
To enable automatic synchronization with a time server, follow the next steps:
1. Move the Enable NTP switch to the right.
2. Specify the needed NTP server or leave the value specified by default in the NTP Servers section. If you need to specify several servers, click the ADD SERVER button.
3. Select your time zone from the Timezone drop-down list in the NTP Settings section. To set the time zone in accordance with the settings of your operating system or portable device, click the DETERMINE TIMEZONE button.
4. Click the APPLY button. The System date and System time fields will be filled in automatically.
To enable automatic adjustment for daylight saving time of the router, move the Daylight saving time switch to the right in the NTP Servers section and click the APPLY button.
Page 200 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
In some cases NTP servers addresses are provided by your ISP. In this case, you need to move the
Get NTP server addresses using DHCP switch in the NTP Servers section to the right and click the APPLY button. Contact your ISP to clarify if this setting needs to be enabled. If the Get
NTP server addresses using DHCP switch is moved to the right, the NTP Servers section is not displayed.
To allow connected devices to use the IP address of the router in the local subnet as a time server, move the Run as a server for the local network switch to the right and click the APPLY button.
!
When the router is powered off or rebooted, the system time is reset to the default value.
If you have set automatic synchronization for the system time, the internal clock of the device will be configured after connecting to the Inter net. If you have set the system time manually, you need to set the time and date again (see above).
Page 201 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Yandex.DNS
This menu is designed to configure the Yandex.DNS service.
Yandex.DNS is a web content filtering service which provides the DNS server, protects a computer against malicious web sites, and blocks access to adult web sites.
Settings
On the Yandex.DNS / Settings page, you can enable the Yandex.DNS service and configure its operating mode.
Figure 157. The Yandex.DNS / Settings page.
To get detailed information on the service, click the About Yandex.DNS
link.
To enable the Yandex.DNS service, move the Enable switch to the right.
Page 202 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
When the service is enabled, the Default mode section is displayed on the page. Select the needed choice of the radio button to configure filtering for all devices of the router's network:
• Protection off : when this value is selected, the service provides the DNS server with no restrictions on access to unsafe web sites;
• Safe : when this value is selected, the service blocks access to malicious and fraudulent web sites;
• Child : when this value is selected, the service blocks access to malicious and fraudulent web sites and blocks access to adult content.
Also the selected filtering mode will be applied to all devices newly connected to the router's network.
After specifying all needed parameters, click the APPLY button.
To disable the Yandex.DNS service, move the Enable switch to the left and click the APPLY button.
Page 203 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
Devices and Rules
On the Yandex.DNS / Devices and Rules page, you can specify a filtering mode for each device separately.
Figure 158. The Yandex.DNS / Devices and Rules page.
In the Known Clients section, the devices connected to the local network of the router at the moment and their relevant filtering mode are displayed.
To create 18 a new filtering rule for a device, click the ADD button in the Rules section, or left-click the name of the filtering mode in the line of the device for which a rule should be created in the
Known Clients section.
Figure 159. Adding a new rule for the Yandex.DNS service.
18 When a new rule for filtering is created, a MAC address and IP address pair is displayed on the Connections
Setup / LAN page. The created pair will be deleted with the relevant rule.
Page 204 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Configuring via Web-based Interface
In the opened window, you can specify the following parameters:
Parameter Description
MAC address The MAC address of a device from the router's LAN.
IP address
Name
The IP address of a device from the router's LAN.
Enter a name for the rule for easier identification. Optional .
Mode
Select an operating mode of the Yandex.DNS service for this rule.
Protection off : when this value is selected, the service provides the DNS server with no restrictions on access to unsafe web sites.
Safe : when this value is selected, the service blocks access to malicious and fraudulent web sites.
Child : when this value is selected, the service blocks access to malicious and fraudulent web sites and blocks access to adult content.
After specifying the needed parameters, click the SAVE button.
To edit a rule for filtering, select a relevant line of the table, in the opened window, change the needed values and click the SAVE button.
To remove a rule for filtering, select the checkbox located to the left of the relevant rule and click the DELETE button. Also you can remove a rule in the editing window.
After completing the work with rules, click the APPLY button.
Page 205 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Operation Guidelines
CHAPTER 5. OPERATION GUIDELINES
Safety Rules and Conditions
Please carefully read this section before installation and connection of the device. Make sure that the power adapter and cables are not damaged. The device should be used only as intended in accordance with the documents.
The device is intended for use in dry, clean, dust-free, and well ventilated areas with normal humidity away from strong heat sources. Do not use the device outdoors or in the areas with high humidity. Do not place foreign objects on the device. Do not obstruct the ventilation openings of the device. The environmental temperature near the device and the temperature inside the device's cover should be within the range from 0 °С to +40 °С.
Only use the power adapter supplied with the device. Do not plug in the adapter, if its case or cable are damaged. Plug the adapter only into working electrical outlets with parameters indicated on the adapter.
Do not open the cover of the device! Unplug the device before dusting and cleaning. Use a damp cloth to clean the device. Do not use liquid/aerosol cleaners or magnetic/static cleaning devices.
Prevent moisture getting into the device or the power adapter.
The service life of the device is 2 years.
Page 206 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Operation Guidelines
Wireless Installation Considerations
The DSL-2750U device lets you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range. Typical ranges vary depending on the types of materials and background RF noise in your home or office. To maximize your wireless range, follow the guidelines below.
1. Keep the number of walls and ceilings between the DSL-2750U device and other network devices to a minimum – each wall or ceiling can reduce your wireless network range by 3-
90 feet (1-30 meters).
2. Be aware of the direct line between network devices. Place your devices so that the signal travels straight through a wall or ceiling (instead of at an angle) for better reception.
3. Building materials make a difference. A solid metal door or aluminum studs may have a negative effect on your wireless range. Try to position your router, access points, and computers so that the signal passes through drywalls or open doorways. Materials and objects such as glass, steel, metal, walls with insulation, water (fish tanks), mirrors, file cabinets, brick, and concrete will degrade your wireless signal.
4. Keep your router away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances that generate RF noise.
5. If you are using 2.4 GHz cordless phones or X-10 equipment (wireless devices such as ceiling fans, lights, and home security systems), your wireless connection may degrade dramatically or drop completely. Make sure your 2.4 GHz phone base is as far away from your wireless devices as possible. Note, that the base transmits a signal even if the phone in not in use.
Page 207 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
Abbreviations and Acronyms
CHAPTER 6. ABBREVIATIONS AND ACRONYMS
GSM
IGD
IGMP
IMEI
IMSI
IP
DMZ
DNS
DTIM
FTP
GMT
CCK
CRC
DDNS
DDoS
DHCP
DLNA
3G
AC
AES
ARP
BSSID
IPsec
L2TP
IPoA
ISP
Third Generation
Access Category
Advanced Encryption Standard
Address Resolution Protocol
Basic Service Set Identifier
Complementary Code Keying
Cyclic Redundancy Check
Dynamic Domain Name System
Distributed Denial of Service
Dynamic Host Configuration Protocol
Digital Living Network Alliance
DeMilitarized Zone
Domain Name System
Delivery Traffic Indication Message
File Transfer Protocol
Greenwich Mean Time
Global System for Mobile Communications
Internet Gateway Device
Internet Group Management Protocol
International Mobile Equipment Identity
International Mobile Subscriber Identity
Internet Protocol
Internet Protocol Security
Layer 2 Tunneling Protocol
Internet Protocol over ATM
Internet Service Provider
Page 208 of 210
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
RTS
RTSP
SIM
SIP
SMB
SSID
PPPoE
PSK
PUK
QoS
RADIUS
RIP
LAN
LLC
LCP
LTE
MAC
MTU
NAT
NTP
OFDM
PBC
PIN
PPPoA
TKIP
UPnP
URL
USB
Local Area Network
Logical Link Control
Link Control Protocol
Long Term Evolution
Media Access Control
Maximum Transmission Unit
Network Address Translation
Network Time Protocol
Orthogonal Frequency Division Multiplexing
Push Button Configuration
Personal Identification Number
Point-to-Point Protocol over ATM
Point-to-point protocol over Ethernet
Pre-shared key
PIN Unlock Key
Quality of Service
Remote Authentication in Dial-In User Service
Routing Information Protocol
Request To Send
Real Time Streaming Protocol
Subscriber Identification Module
Session Initiation Protocol
Server Message Block
Service Set Identifier
Temporal Key Integrity Protocol
Universal Plug and Play
Uniform Resource Locator
Universal Serial Bus
Page 209 of 210
Abbreviations and Acronyms
DSL-2750U Wireless ADSL2+ Router with 3G/LTE/Ethernet WAN Support and USB Port
User Manual
VC
VCI
VLAN
VPI
WAN
WEP
Wi-Fi
WLAN
WPA
WPS
Virtual Circuit
Virtual Circuit Identifier
Virtual Local Area Network
Virtual Path Identifier
Wide Area Network
Wired Equivalent Privacy
Wireless Fidelity
Wireless Local Area Network
Wi-Fi Protected Access
Wi-Fi Protected Setup
Abbreviations and Acronyms
Page 210 of 210
Download
Public link updated
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Document public link
Advertisement
Key features
Black
Wi-Fi 4 (802.11n)
Fast Ethernet
DSL WAN
Ethernet LAN (RJ-45) ports: 4
Quality of Service (QoS) support
Frequently asked questions
You can access the web-based interface by entering the IP address 192.168.1.1 or the domain name dlinkrouter.local in your web browser's address bar.
The router supports the following WAN connection types: ADSL, 3G, LTE, PPPoE, PPPoA, IPoA, Static/Dynamic IPv4 IPv6, and Bridge.
The wireless Wi-Fi network can be turned on/off by the WIRELESS ON/OFF button on the back panel of the router.
Press and hold the RESET button (located on the bottom panel) for about 10 seconds while the device is powered on.
The WPS button is used to set up a wireless connection.
