STMicroelectronics STM32H733VG Datasheet

STM32H733VG STM32H733ZG
Arm® Cortex®-M7 32-bit 550 MHz MCU, 1 MB Flash, 564 KB RAM,
Ethernet, USB, 3x FD-CAN, Graphics, 2x 16-bit ADCs, crypto/hash
Datasheet - production data
Features
Includes ST state-of-the-art patented
technology
LQFP100
(14x14 mm)
Core
LQFP144
(20x20 mm)
FBGA
• 32-bit Arm® Cortex®-M7 CPU with DP-FPU, L1
cache: 32-Kbyte data cache and 32-Kbyte
instruction cache allowing 0-wait state
execution from embedded Flash memory and
external memories, frequency up to 550 MHz,
MPU, 1177 DMIPS/2.14 DMIPS/MHz
(Dhrystone 2.1), and DSP instructions
Clock, reset and supply management
Memories
• 1.62 V to 3.6 V application supply and I/O
• 1 Mbyte of embedded Flash memory with ECC
• POR, PDR, PVD and BOR
TFBGA100
(8x8 mm)
• SRAM: total 564 Kbytes all with ECC, including
128 Kbytes of data TCM RAM for critical realtime data + 432 Kbytes of system RAM (up to
256 Kbytes can remap on instruction TCM
RAM for critical real time instructions) +
4 Kbytes of backup SRAM (available in the
lowest-power modes)
• Dedicated USB power
• Flexible external memory controller with up to
16-bit data bus: SRAM, PSRAM,
SDRAM/LPSDR SDRAM, NOR/NAND
memories
Low power
• 2 x Octo-SPI interface with XiP and on-the-fly
decryption support
• 2 x SD/SDIO/MMC interface
FBGA
UFBGA144
(7x7 mm)
• Embedded LDO regulator
• Internal oscillators: 64 MHz HSI, 48 MHz
HSI48, 4 MHz CSI, 32 kHz LSI
• External oscillators: 4-50 MHz HSE,
32.768 kHz LSE
• Sleep, Stop and Standby modes
• VBAT supply for RTC, 32×32-bit backup
registers
Analog
• Bootloader with security services support (SFI
and SB-SFU)
• 2×16-bit ADC, up to 3.6 MSPS in 16-bit: up to
18 channels and 7.2 MSPS in doubleinterleaved mode
Graphics
• 1 x 12-bit ADC, up to 5 MSPS in 12-bit, up to 12
channels
• Chrom-ART Accelerator graphical hardware
accelerator enabling enhanced graphical user
interface to reduce CPU load
• LCD-TFT controller supporting up to XGA
resolution
December 2021
• 2 x comparators
• 2 x operational amplifier GBW = 8 MHz
• 2× 12-bit D/A converters
DS13314 Rev 3
1/236
www.st.com
STM32H733xG
Digital filters for sigma delta modulator
(DFSDM)
• 8 channels/4 filters
• SWPMI single-wire protocol master I/F
• MDIO slave interface
Mathematical acceleration
4 DMA controllers to offload the CPU
• 1 × MDMA with linked list support
• CORDIC for trigonometric functions
acceleration
• 2 × dual-port DMAs with FIFO
• FMAC: Filter mathematical accelerator
• 1 × basic DMA with request router capabilities
Digital temperature sensor
24 timers
Cryptographic/HASH acceleration
• Seventeen 16-bit (including 5 x low power
16-bit timer available in stop mode) and four
32-bit timers, each with up to 4 IC/OC/PWM or
pulse counter and quadrature (incremental)
encoder input
• 2x watchdogs, 1x SysTick timer
• AES 128, 192, 256, TDES, HASH (MD5, SHA1, SHA-2), HMAC
• 2x OTFDEC AES-128 in CTR mode for OctoSPI memory encryption/decryption
True random number generator
Debug mode
CRC calculation unit
• SWD and JTAG interfaces
RTC with sub-second accuracy and
hardware calendar
• 2-Kbyte embedded trace buffer
Up to 114 I/O ports with interrupt
capability
ROP, PC-ROP, tamper detection, secure
firmware upgrade support
Up to 35 communication interfaces
96-bit unique ID
• Up to 5 × I2C FM+ interfaces
(SMBus/PMBus™)
All packages are ECOPACK2 compliant
• Up to 5 USARTs/5 UARTs (ISO7816 interface,
LIN, IrDA, modem control) and 1 x LPUART
• Up to 6 SPIs with 4 with muxed duplex I2S for
audio class accuracy via internal audio PLL or
external clock and up to 5 x SPI (from 5 x
USART when configured in synchronous
mode)
• 2x SAI (serial audio interface)
• 1× FD/TT-CAN and 2x FD-CAN
• 8- to 14-bit camera interface
• 16-bit parallel slave synchronous interface
• SPDIF-IN interface
• HDMI-CEC
• Ethernet MAC interface with DMA controller
• USB 2.0 high-speed/full-speed
device/host/OTG controller with dedicated
DMA, on-chip FS PHY and ULPI for external
HS PHY
2/236
DS13314 Rev 3
STM32H733xG
Contents
Contents
1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3
Functional overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.1
Arm® Cortex®-M7 with FPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.2
Memory protection unit (MPU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.3
Memories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.3.1
Embedded Flash memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.3.2
Embedded SRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Error code correction (ECC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
3.4
Secure access mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.5
Boot modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.6
CORDIC co-processor (CORDIC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
CORDIC features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
3.7
Filter mathematical accelerator (FMAC) . . . . . . . . . . . . . . . . . . . . . . . . . . 24
FMAC features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
3.8
Power supply management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.8.1
Power supply scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.8.2
Power supply supervisor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.8.3
Voltage regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.9
Low-power strategy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.10
Reset and clock controller (RCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.10.1
Clock management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.10.2
System reset sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3.11
General-purpose input/outputs (GPIOs) . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3.12
Bus-interconnect matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3.13
DMA controllers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3.14
Chrom-ART Accelerator (DMA2D) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3.15
Nested vectored interrupt controller (NVIC) . . . . . . . . . . . . . . . . . . . . . . . 31
3.16
Extended interrupt and event controller (EXTI) . . . . . . . . . . . . . . . . . . . . 31
3.17
Cyclic redundancy check calculation unit (CRC) . . . . . . . . . . . . . . . . . . . 31
3.18
Flexible memory controller (FMC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
DS13314 Rev 3
3/236
7
Contents
4/236
STM32H733xG
3.19
Octo-SPI memory interface (OCTOSPI) . . . . . . . . . . . . . . . . . . . . . . . . . 32
3.20
Analog-to-digital converters (ADCs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
3.21
Temperature sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
3.22
Digital temperature sensor (DTS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
3.23
VBAT operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
3.24
Digital-to-analog converters (DAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
3.25
Ultra-low-power comparators (COMP) . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3.26
Operational amplifiers (OPAMP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3.27
Digital filter for sigma-delta modulators (DFSDM) . . . . . . . . . . . . . . . . . . 36
3.28
Digital camera interface (DCMI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
3.29
PSSI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
3.30
LCD-TFT controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
3.31
True random number generator (RNG) . . . . . . . . . . . . . . . . . . . . . . . . . . 39
3.32
Cryptographic acceleration (CRYP and HASH) . . . . . . . . . . . . . . . . . . . . 39
3.33
On-the-fly decryption engine (OTFDEC) . . . . . . . . . . . . . . . . . . . . . . . . . 39
3.34
Timers and watchdogs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
3.34.1
Advanced-control timers (TIM1, TIM8) . . . . . . . . . . . . . . . . . . . . . . . . . 43
3.34.2
General-purpose timers (TIMx) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
3.34.3
Basic timers TIM6 and TIM7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
3.34.4
Low-power timers (LPTIM1, LPTIM2, LPTIM3, LPTIM4, LPTIM5) . . . . 44
3.34.5
Independent watchdog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
3.34.6
Window watchdog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
3.34.7
SysTick timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
3.35
Real-time clock (RTC), backup SRAM and backup registers . . . . . . . . . . 45
3.36
Inter-integrated circuit interface (I2C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
3.37
Universal synchronous/asynchronous receiver transmitter (USART) . . . 46
3.38
Low-power universal asynchronous receiver transmitter (LPUART) . . . . 47
3.39
Serial peripheral interface (SPI)/inter- integrated sound interfaces (I2S) . 48
3.40
Serial audio interfaces (SAI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
3.41
SPDIFRX Receiver Interface (SPDIFRX) . . . . . . . . . . . . . . . . . . . . . . . . . 49
3.42
Single wire protocol master interface (SWPMI) . . . . . . . . . . . . . . . . . . . . 49
3.43
Management data input/output (MDIO) slaves . . . . . . . . . . . . . . . . . . . . . 50
3.44
SD/SDIO/MMC card host interfaces (SDMMC) . . . . . . . . . . . . . . . . . . . . 50
3.45
Controller area network (FDCAN1, FDCAN2, FDCAN3) . . . . . . . . . . . . . 50
DS13314 Rev 3
STM32H733xG
Contents
3.46
Universal serial bus on-the-go high-speed (OTG_HS) . . . . . . . . . . . . . . . 51
3.47
Ethernet MAC interface with dedicated DMA controller (ETH) . . . . . . . . . 51
3.48
High-definition multimedia interface (HDMI)
- consumer electronics control (CEC) . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
3.49
Debug infrastructure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
4
Memory mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
5
Pinouts, pin descriptions and alternate functions . . . . . . . . . . . . . . . . 54
6
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
6.1
Parameter conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
6.1.1
Minimum and maximum values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
6.1.2
Typical values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
6.1.3
Typical curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
6.1.4
Loading capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
6.1.5
Pin input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
6.1.6
Power supply scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
6.1.7
Current consumption measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
6.2
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
6.3
Operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
6.3.1
General operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
6.3.2
VCAP external capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
6.3.3
Operating conditions at power-up / power-down . . . . . . . . . . . . . . . . . . 94
6.3.4
Embedded reset and power control block characteristics . . . . . . . . . . . 95
6.3.5
Embedded reference voltage characteristics . . . . . . . . . . . . . . . . . . . . . 96
6.3.6
Embedded USB regulator characteristics . . . . . . . . . . . . . . . . . . . . . . . 97
6.3.7
Supply current characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Typical and maximum current consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
I/O system current consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103
On-chip peripheral current consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105
6.3.8
Wakeup time from low-power modes . . . . . . . . . . . . . . . . . . . . . . . . . . 112
6.3.9
External clock source characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . 113
High-speed external user clock generated from an external source . . . . . . . . .113
Low-speed external user clock generated from an external source . . . . . . . . . .114
High-speed external clock generated from a crystal/ceramic resonator. . . . . . .115
Low-speed external clock generated from a crystal/ceramic resonator . . . . . . .116
6.3.10
Internal clock source characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . 117
DS13314 Rev 3
5/236
7
Contents
STM32H733xG
48 MHz high-speed internal RC oscillator (HSI48) . . . . . . . . . . . . . . . . . . . . . . .117
64 MHz high-speed internal RC oscillator (HSI) . . . . . . . . . . . . . . . . . . . . . . . . .118
4 MHz low-power internal RC oscillator (CSI) . . . . . . . . . . . . . . . . . . . . . . . . . .119
Low-speed internal (LSI) RC oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119
6.3.11
PLL characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
6.3.12
Memory characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Flash memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124
6.3.13
EMC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Functional EMS (electromagnetic susceptibility) . . . . . . . . . . . . . . . . . . . . . . . .125
Designing hardened software to avoid noise problems . . . . . . . . . . . . . . . . . . .125
Electromagnetic Interference (EMI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .126
6.3.14
Absolute maximum ratings (electrical sensitivity) . . . . . . . . . . . . . . . . 126
Electrostatic discharge (ESD). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .126
Static latchup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127
6.3.15
I/O current injection characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Functional susceptibility to I/O current injection . . . . . . . . . . . . . . . . . . . . . . . . .127
6.3.16
I/O port characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
General input/output characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .128
Output driving current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129
Output voltage levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .130
Output buffer timing characteristics (HSLV option disabled) . . . . . . . . . . . . . . .132
Output buffer timing characteristics (HSLV option enabled). . . . . . . . . . . . . . . .134
Analog switch between ports Pxy_C and Pxy . . . . . . . . . . . . . . . . . . . . . . . . . .135
6.3.17
NRST pin characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
6.3.18
FMC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Asynchronous waveforms and timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .136
Synchronous waveforms and timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .144
NAND controller waveforms and timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .152
SDRAM waveforms and timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .155
6.3.19
Octo-SPI interface characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
6.3.20
Delay block (DLYB) characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
6.3.21
16-bit ADC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
General PCB design guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .171
6/236
6.3.22
12-bit ADC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
6.3.23
DAC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
6.3.24
Voltage reference buffer characteristics . . . . . . . . . . . . . . . . . . . . . . . 182
6.3.25
Analog temperature sensor characteristics . . . . . . . . . . . . . . . . . . . . . 183
6.3.26
Digital temperature sensor characteristics . . . . . . . . . . . . . . . . . . . . . . 184
6.3.27
Temperature and VBAT monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
6.3.28
Voltage booster for analog switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
DS13314 Rev 3
STM32H733xG
Contents
6.3.29
Comparator characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
6.3.30
Operational amplifier characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . 186
6.3.31
Digital filter for Sigma-Delta Modulators (DFSDM) characteristics . . . 189
6.3.32
Camera interface (DCMI) timing specifications . . . . . . . . . . . . . . . . . . 191
6.3.33
Parallel synchronous slave interface (PSSI) characteristics . . . . . . . . 192
6.3.34
LCD-TFT controller (LTDC) characteristics . . . . . . . . . . . . . . . . . . . . . 193
6.3.35
Timer characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
6.3.36
Low-power timer characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
6.3.37
Communication interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
I2C interface characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .196
USART interface characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .197
SPI interface characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .199
I2S Interface characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .202
SAI characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .204
MDIO characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .206
SD/SDIO MMC card host interface (SDMMC) characteristics . . . . . . . . . . . . . .207
USB OTG_FS characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .209
USB OTG_HS characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .210
Ethernet interface characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .211
JTAG/SWD interface characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .213
7
Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216
7.1
LQFP100 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
Device marking for LQFP100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .220
7.2
TFBGA100 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221
Device marking for TFBGA100. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .223
7.3
LQFP144 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
Device marking for LQFP144 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .227
7.4
UFBGA144 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228
Device marking for UFBGA144 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .230
7.5
Thermal characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231
7.5.1
Reference documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232
8
Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233
9
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234
DS13314 Rev 3
7/236
7
List of tables
STM32H733xG
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
Table 9.
Table 10.
Table 11.
Table 12.
Table 13.
Table 14.
Table 15.
Table 16.
Table 17.
Table 18.
Table 19.
Table 20.
Table 21.
Table 22.
Table 23.
Table 24.
Table 25.
Table 26.
Table 27.
Table 28.
Table 29.
Table 30.
Table 31.
Table 32.
Table 33.
Table 34.
Table 35.
Table 36.
Table 37.
Table 38.
Table 39.
Table 40.
Table 41.
Table 42.
Table 43.
Table 44.
8/236
STM32H733xG features and peripheral counts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
System versus domain low-power mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
DFSDM implementation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Timer feature comparison . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
USART features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Legend/abbreviations used in the pinout table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
STM32H733 pin and ball descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
STM32H733 pin alternate functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Voltage characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Current characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Thermal characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
General operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Supply voltage and maximum temperature configuration. . . . . . . . . . . . . . . . . . . . . . . . . . 93
VCAP operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Operating conditions at power-up/power-down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Reset and power control block characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Embedded reference voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Internal reference voltage calibration values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
USB regulator characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Typical and maximum current consumption in Run mode,
code with data processing running from ITCM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Typical and maximum current consumption in Run mode, code with data processing
running from Flash memory, cache ON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Typical and maximum current consumption in Run mode,
code with data processing running from Flash memory, cache OFF. . . . . . . . . . . . . . . . 101
Typical consumption in Run mode and corresponding performance
versus code position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Typical current consumption in Autonomous mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Typical and maximum current consumption in Sleep mode . . . . . . . . . . . . . . . . . . . . . . . 102
Typical and maximum current consumption in Stop mode . . . . . . . . . . . . . . . . . . . . . . . . 103
Typical and maximum current consumption in Standby mode . . . . . . . . . . . . . . . . . . . . . 103
Typical and maximum current consumption in VBAT mode . . . . . . . . . . . . . . . . . . . . . . . 103
Peripheral current consumption in Run mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Low-power mode wakeup timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
High-speed external user clock characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Low-speed external user clock characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
4-50 MHz HSE oscillator characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Low-speed external user clock characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
HSI48 oscillator characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
HSI oscillator characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
CSI oscillator characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
LSI oscillator characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
PLL1 characteristics (wide VCO frequency range) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
PLL1 characteristics (medium VCO frequency range) . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
PLL2 and PLL3 characteristics (wide VCO frequency range) . . . . . . . . . . . . . . . . . . . . . 122
PLL2 and PLL3 characteristics (medium VCO frequency range) . . . . . . . . . . . . . . . . . . . 123
Flash memory characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Flash memory programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
DS13314 Rev 3
STM32H733xG
Table 45.
Table 46.
Table 47.
Table 48.
Table 49.
Table 50.
Table 51.
Table 52.
Table 53.
Table 54.
Table 55.
Table 56.
Table 57.
Table 58.
Table 59.
Table 60.
Table 61.
Table 62.
Table 63.
Table 64.
Table 65.
Table 66.
Table 67.
Table 68.
Table 69.
Table 70.
Table 71.
Table 72.
Table 73.
Table 74.
Table 75.
Table 76.
Table 77.
Table 78.
Table 79.
Table 80.
Table 81.
Table 82.
Table 83.
Table 84.
Table 85.
Table 86.
Table 87.
Table 88.
Table 89.
Table 90.
Table 91.
Table 92.
Table 93.
Table 94.
Table 95.
Table 96.
List of tables
Flash memory endurance and data retention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
EMS characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
EMI characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
ESD absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Electrical sensitivities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
I/O current injection susceptibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
I/O static characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Output voltage characteristics for all I/Os except PC13, PC14 and PC15 . . . . . . . . . . . . 130
Output voltage characteristics for PC13, PC14 and PC15 . . . . . . . . . . . . . . . . . . . . . . . . 131
Output timing characteristics (HSLV OFF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Output timing characteristics (HSLV ON) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Pxy_C and Pxy analog switch characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
NRST pin characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Asynchronous non-multiplexed SRAM/PSRAM/NOR read timings . . . . . . . . . . . . . . . . . 138
Asynchronous non-multiplexed SRAM/PSRAM/NOR read-NWAIT timings . . . . . . . . . . . 138
Asynchronous non-multiplexed SRAM/PSRAM/NOR write timings . . . . . . . . . . . . . . . . . 140
Asynchronous non-multiplexed SRAM/PSRAM/NOR write-NWAIT timings. . . . . . . . . . . 140
Asynchronous multiplexed PSRAM/NOR read timings. . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Asynchronous multiplexed PSRAM/NOR read-NWAIT timings . . . . . . . . . . . . . . . . . . . . 142
Asynchronous multiplexed PSRAM/NOR write timings . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Asynchronous multiplexed PSRAM/NOR write-NWAIT timings . . . . . . . . . . . . . . . . . . . . 143
Synchronous multiplexed NOR/PSRAM read timings . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Synchronous multiplexed PSRAM write timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Synchronous non-multiplexed NOR/PSRAM read timings . . . . . . . . . . . . . . . . . . . . . . . . 149
Synchronous non-multiplexed PSRAM write timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
Switching characteristics for NAND Flash read cycles . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
Switching characteristics for NAND Flash write cycles. . . . . . . . . . . . . . . . . . . . . . . . . . . 154
SDRAM read timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
LPSDR SDRAM read timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
SDRAM Write timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
LPSDR SDRAM Write timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
OCTOSPI characteristics in SDR mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
OCTOSPI characteristics in DTR mode (no DQS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
OCTOSPI characteristics in DTR mode (with DQS)/Octal and Hyperbus . . . . . . . . . . . . 161
Delay Block characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
16-bit ADC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Minimum sampling time vs RAIN (16-bit ADC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
16-bit ADC accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
12-bit ADC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
Minimum sampling time vs RAIN (12-bit ADC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
12-bit ADC accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
DAC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
DAC accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
VREFBUF characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
Temperature sensor characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
Temperature sensor calibration values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
Digital temperature sensor characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
VBAT monitoring characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
VBAT charging characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
Temperature monitoring characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
Voltage booster for analog switch characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
COMP characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
DS13314 Rev 3
9/236
10
List of tables
Table 97.
Table 98.
Table 99.
Table 100.
Table 101.
Table 102.
Table 103.
Table 104.
Table 105.
Table 106.
Table 107.
Table 108.
Table 109.
Table 110.
Table 111.
Table 112.
Table 113.
Table 114.
Table 115.
Table 116.
Table 117.
Table 118.
Table 119.
Table 120.
Table 121.
Table 122.
Table 123.
Table 124.
Table 125.
Table 126.
Table 127.
Table 128.
10/236
STM32H733xG
Operational amplifier characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186
DFSDM measured timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
DCMI characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
PSSI transmit characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
PSSI receive characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
LTDC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
TIMx characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
LPTIMx characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
Minimum i2c_ker_ck frequency in all I2C modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
I2C analog filter characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
USART characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
SPI characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
I2S dynamic characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202
SAI characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204
MDIO Slave timing parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206
Dynamics characteristics: SD / MMC characteristics, VDD = 2.7 to 3.6 V . . . . . . . . . . . . 207
Dynamics characteristics: eMMC characteristics VDD = 1.71V to 1.9V . . . . . . . . . . . . . . 208
USB OTG_FS electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210
Dynamics characteristics: USB ULPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210
Dynamics characteristics: Ethernet MAC signals for SMI . . . . . . . . . . . . . . . . . . . . . . . . 211
Dynamics characteristics: Ethernet MAC signals for RMII . . . . . . . . . . . . . . . . . . . . . . . . 212
Dynamics characteristics: Ethernet MAC signals for MII . . . . . . . . . . . . . . . . . . . . . . . . . 213
Dynamics JTAG characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214
Dynamics SWD characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214
LQFP100 - Mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 218
TFBGA100 - Mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
TFBGA100 - Recommended PCB design rules (0.8 mm pitch BGA) . . . . . . . . . . . . . . . . 223
LQFP144 - Mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225
UFBGA144 - Mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228
UFBGA144 - Recommended PCB design rules (0.50 mm pitch BGA). . . . . . . . . . . . . . . 229
Thermal characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231
Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234
DS13314 Rev 3
STM32H733xG
List of figures
List of figures
Figure 1.
STM32H733xG block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Figure 2.
Power-up/power-down sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Figure 3.
STM32H733xG bus matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Figure 4.
TFBGA100 pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Figure 5.
LQFP100 pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Figure 6.
LQFP144 pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Figure 7.
UFBGA144 ballout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Figure 8.
Pin loading conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Figure 9.
Pin input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Figure 10. Power supply scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Figure 11. Current consumption measurement scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Figure 12. External capacitor CEXT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Figure 13. High-speed external clock source AC timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Figure 14. Low-speed external clock source AC timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Figure 15. Typical application with an 8 MHz crystal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Figure 16. Typical application with a 32.768 kHz crystal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Figure 17. VIL/VIH for all I/Os except BOOT0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Figure 18. Recommended NRST pin protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Figure 19. Asynchronous non-multiplexed SRAM/PSRAM/NOR read waveforms . . . . . . . . . . . . . . 137
Figure 20. Asynchronous non-multiplexed SRAM/PSRAM/NOR write waveforms . . . . . . . . . . . . . . 139
Figure 21. Asynchronous multiplexed PSRAM/NOR read waveforms. . . . . . . . . . . . . . . . . . . . . . . . 141
Figure 22. Synchronous multiplexed NOR/PSRAM read timings . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Figure 23. Synchronous multiplexed PSRAM write timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Figure 24. Synchronous non-multiplexed NOR/PSRAM read timings . . . . . . . . . . . . . . . . . . . . . . . . 148
Figure 25. Synchronous non-multiplexed PSRAM write timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Figure 26. NAND controller waveforms for read access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Figure 27. NAND controller waveforms for write access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
Figure 28. NAND controller waveforms for common memory read access . . . . . . . . . . . . . . . . . . . . 153
Figure 29. NAND controller waveforms for common memory write access. . . . . . . . . . . . . . . . . . . . 154
Figure 30. SDRAM read access waveforms (CL = 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Figure 31. SDRAM write access waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
Figure 32. OCTOSPI SDR read/write timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Figure 33. OCTOSPI DTR mode timing diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
Figure 34. OCTOSPI Hyperbus clock timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Figure 35. OCTOSPI Hyperbus read timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Figure 36. OCTOSPI Hyperbus write timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Figure 37. ADC accuracy characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
Figure 38. Typical connection diagram when using the ADC with FT/TT pins
featuring analog switch function170
Figure 39. Power supply and reference decoupling (VREF+ not connected to VDDA). . . . . . . . . . . . . 171
Figure 40. Power supply and reference decoupling (VREF+ connected to VDDA). . . . . . . . . . . . . . . . 171
Figure 41. 12-bit buffered /non-buffered DAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
Figure 42. Channel transceiver timing diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
Figure 43. DCMI timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
Figure 44. LCD-TFT horizontal timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
Figure 45. LCD-TFT vertical timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
Figure 46. USART timing diagram in Master mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198
Figure 47. USART timing diagram in Slave mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198
DS13314 Rev 3
11/236
12
List of figures
Figure 48.
Figure 49.
Figure 50.
Figure 51.
Figure 52.
Figure 53.
Figure 54.
Figure 55.
Figure 56.
Figure 57.
Figure 58.
Figure 59.
Figure 60.
Figure 61.
Figure 62.
Figure 63.
Figure 64.
Figure 65.
Figure 66.
Figure 67.
Figure 68.
Figure 69.
Figure 70.
Figure 71.
Figure 72.
Figure 73.
Figure 74.
Figure 75.
12/236
STM32H733xG
SPI timing diagram - slave mode and CPHA = 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200
SPI timing diagram - slave mode and CPHA = 1(1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201
SPI timing diagram - master mode(1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201
I2S slave timing diagram (Philips protocol)(1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203
I2S master timing diagram (Philips protocol)(1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203
SAI master timing waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205
SAI slave timing waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206
MDIO Slave timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207
SD high-speed mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209
SD default mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209
SDMMC DDR mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209
ULPI timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211
Ethernet SMI timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212
Ethernet RMII timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212
Ethernet MII timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213
JTAG timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214
SWD timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215
LQFP100- Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
LQFP100 - Recommended footprint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219
LQFP100 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220
TFBGA100 - Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221
TFBGA100 - Recommended footprint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
TFBGA100 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223
LQFP144 - Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
LQFP144 - Recommended footprint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 226
LQFP144 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227
UFBGA144 - Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228
UFBGA144 - Recommended footprint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229
UFBGA144 marking example (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230
DS13314 Rev 3
STM32H733xG
1
Introduction
Introduction
This document provides information on STM32H733xG microcontrollers, such as
description, functional overview, pin assignment and definition, packaging, and ordering
information.
This document should be read in conjunction with the STM32H733xG reference manual
(RM0468), available from the STMicroelectronics website www.st.com.
For information on the device errata with respect to the datasheet and reference manual,
refer to the STM32H733 errata sheet (ES0491) available on the STMicroelectronics website
www.st.com.
For information on the Arm®(a) Cortex®-M7 core, refer to the Cortex®-M7 Technical
Reference Manual, available from the http://www.arm.com website.
a. Arm is a registered trademark of Arm Limited (or its subsidiaries) in the US and/or elsewhere.
DS13314 Rev 3
13/236
53
Description
2
STM32H733xG
Description
STM32H733xG devices are based on the high-performance Arm® Cortex®-M7 32-bit RISC
core operating at up to 550 MHz. The Cortex® -M7 core features a floating point unit (FPU)
which supports Arm® double-precision (IEEE 754 compliant) and single-precision dataprocessing instructions and data types. The Cortex -M7 core includes 32 Kbytes of
instruction cache and 32 Kbytes of data cache. STM32H733xG devices support a full set of
DSP instructions and a memory protection unit (MPU) to enhance application security.
STM32H733xG devices incorporate high-speed embedded memories with 1 Mbyte of Flash
memory, up to 564 Kbytes of RAM (including 192 Kbytes that can be shared between ITCM
and AXI, plus 64 Kbytes exclusively ITCM, plus 128 Kbytes exclusively AXI, 128 Kbyte
DTCM, 48 Kbytes AHB and 4 Kbytes of backup RAM), as well as an extensive range of
enhanced I/Os and peripherals connected to APB buses, AHB buses, 2x32-bit multi-AHB
bus matrix and a multi layer AXI interconnect supporting internal and external memory
access. To improve application robustness, all memories feature error code correction (one
error correction, two error detections).
The devices embed peripherals allowing mathematical/arithmetic function acceleration
(CORDIC coprocessor for trigonometric functions and FMAC unit for filter functions). All the
devices offer three ADCs, two DACs, two operational amplifiers, two ultra-low power
comparators, a low-power RTC, 4 general-purpose 32-bit timers, 12 general-purpose 16-bit
timers including two PWM timers for motor control, five low-power timers, a true random
number generator (RNG), and a cryptographic acceleration cell, and a HASH processor.
The devices support four digital filters for external sigma-delta modulators (DFSDM). They
also feature standard and advanced communication interfaces.
•
14/236
Standard peripherals
–
Five I2Cs
–
Five USARTs, five UARTs and one LPUART
–
Six SPIs, four I2Ss in Half-duplex mode. To achieve audio class accuracy, the I2S
peripherals can be clocked by a dedicated internal audio PLL or by an external
clock to allow synchronization (note that the five USARTs also provide SPI slave
capability).
–
Two SAI serial audio interfaces
–
One SPDIFRX interface with four inputs
–
One SWPMI (Single Wire Protocol Master Interface)
–
Management Data Input/Output (MDIO) slaves
–
Two SDMMC interfaces
–
A USB OTG high-speed interface with full-speed capability (with the ULPI)
–
Two FDCANs plus one TT-FDCAN interface
–
An Ethernet interface
–
Chrom-ART Accelerator
–
HDMI-CEC
DS13314 Rev 3
STM32H733xG
•
Description
Advanced peripherals including
–
A flexible memory control (FMC) interface
–
Two Octo-SPI memory interfaces with on-the-fly decryption (OTFDEC)
–
A camera interface for CMOS sensors
–
An LCD-TFT display controller
Refer to Table 1: STM32H733xG features and peripheral counts for the list of peripherals
available on each part number.
STM32H733xG devices operate in the –40 to +85 °C ambient temperature range from a
1.62 to 3.6 V power supply. The supply voltage can drop down to 1.62 V by using an
external power supervisor (see Section 3.8.2: Power supply supervisor) and connecting the
PDR_ON pin to VSS. Otherwise the supply voltage must stay above 1.71 V with the
embedded power voltage detector enabled.
Dedicated supply inputs for USB are available to allow a greater power supply choice.
A comprehensive set of power-saving modes allows the design of low-power applications.
STM32H733xG devices are offered in several packages ranging from 100 to 144 pins/balls.
The set of included peripherals changes with the device chosen.
These features make STM32H733xG microcontrollers suitable for a wide range of
applications:
•
Motor drive and application control
•
Medical equipment
•
Industrial applications: PLC, inverters, circuit breakers
•
Printers, and scanners
•
Alarm systems, video intercom, and HVAC
•
Home audio appliances
•
Mobile applications, Internet of Things
•
Wearable devices: smart watches.
Figure 1 shows the device block diagram.
DS13314 Rev 3
15/236
53
Description
STM32H733xG
Figure 1. STM32H733xG block diagram
MII / RMII
To APB1-2
peripherals
MDIO
as AF
AHB1
D-TCM
64KB
I-TCM 64KB
Arm CPU
Cortex-M7
550 MHz
LCD-TFT
FIFO
WWDG
RNG
HASH
3DES/AES
SRAM1 SRAM2
16 KB 16 KB
ADC1
CORDIC
OCTOSPI2
signals
FMAC
AHB3
FIFO
SDMMC1
TIM6
AXI/AHB34 (275MHz)
16b
TIM7
16b
SWPMI
AHB4
AHB2 (275MHz)
DCMI
PSSI
Up to 20 analog inputs Most
are common to ADC1 & 2
ADC2
AHB/APB
DLYBOS1-2
AHB/APB
DLYBSD2
HSYNC, VSYNC, PIXCLK, D[13:0]
PDCK, DE, RDY, D[15:0]
AHB1 (275MHz)
OCTOSPI1
signals
DLYBSD1
D[7:0], D123DIR, D0DIR,
CMD, CKas AF
DMA
Mux1
FMC_signals
AHB2 (275MHz)
OTFDEC1
OTFDEC2
APB3 (138MHz)
FIFO
64-bit AXI BUS-MATRIX
16 Streams
FIFO
CHROM-ART
(DMA2D)
32-bit AHB BUS-MATRIX
FMC
AHBS
LCD_R[7:0], LCD_G[7:0],
LCD_B[7:0], LCD_HSYNC,
LCD_VSYNC, LCD_DE, LCD_CLK
DMA/
FIFO
FIFO
1 MB FLASH
D-Cache
32KB
MDMA
DMA/
FIFO
8 Stream 8 Stream
FIFOs
FIFOs
AXIM
ETM
I-Cache
32KB
DMA2
(275MHz)
PHY
ETHER
SDMMC2 OTG_HS
MAC
AXI/AHB12 (275MHz)
OCTOSPIM
TRACECLK
TRACED[3:0]
JTAG/SW
128 KB AXI
SRAM
OCTOSPI1
NJTRST, JTDI,
JTCK/SWCLK
JTDO/SWDIO, JTDO
DMA1
Shared AXI
I-TCM 192KB
AHBP
OCTOSPI2
D-TCM
64KB
D[7:0],DP, DM, STP,
D123DIR, NXT,ULPI:CK
D0DIR, , D[7:0], DIR,
CMD, CKas AF ID, VBUS
32b
TIM2
CH[4;1], ETR as AF
16b
TIM3
CH[4;1], ETR as AF
16b
TIM4
CH[4;1], ETR as AF
32b
TIM5
CH[4;1], ETR as AF
32b
TIM23
CH[4;1], ETR as AF
32b
TIM24
CH[4;1], ETR as AF
16b
TIM12
CH[2;1] as AF
16b
TIM13
CH1 as AF
16b
TIM14
CH1 as AF
AHB/APB
USART2
RX, TX, CK, CTS, RTS, DE as A
USART3
FIFO
AHB4
USART10
RX, TX, CK, CTS, RTS, DE as AF
USART6
16b
16b
A P B 10 MHz
3
MOSI, MISO, SCK, NSS /
SDO, SDI, CK, WS, MCK, as AF
MOSI, MISO, SCK, NSS /
SDO, SDI, CK, WS, MCK, as AF
SCL, SDA, SMBA as AF
I2C3/SMBUS
I2C5/SMBUS
SCL, SDA, SMBA as AF
MDIOS
MDC, MDIO as AF
TT-FDCAN1
FDCAN2
FDCAN3
16 KB SRAM
4 KB BKP
RAM
SPDIFRX1
HDMI-CEC
GPIO PORTJ,K
16b
RCC
Reset &
control
SAI4
COMP1&2
16b
OUT as AF
LPTIM4
16b
OUT as AF
LPTIM3
16b
I2C4
MOSI, MISO, SCK, NSS /
SDO, SDI, CK, WS, MCK, as AF
SPI6/I2S6
RX, TX, CK, CTS, RTS as AF
LPUART1
IN1, IN2, ETR, OUT as AF
LPTIM2
16b
AHB/APB
VREF
IN1, IN2, ETR, OUT as AF
VINM, VINP, VOUT as AF
OPAMP2
VINM, VINP, VOUT as AF
Voltage
regulator
3.3 to 1.2V
@VDD
IWDG
HSI RC
HSI
HSI48
HSI48 RC
CSI
CSI RC
LSI
LSI RC
VDD
VSS
VCAP, VDDLDO
VBAT
XTAL 32 kHz
Temperature
sensor
CEC as AF
OUT1, OUT2 as AF
LPTIM1
@VSW
SYSCFG
EXTI WKUP
IN[1:4] as AF
OPAMP1
LS
OUT as AF
LPTIM5
TX, RX, RXFD_MODE,
TXFD_MODE as AF
TX, RX, RXFD_MODE,
TXFD_MODE as AF
TX, RX, RXFD_MODE,
TXFD_MODE as AF
@VDD
VCORE BBgen + POWER MNGT
PWRCTRL
GPIO PORTA.. H
SCL, SDA, SMBA as AF
SCL, SDA, SMBA as AF
USBCR
DAC
PA..H[15:0]
SCL, SDA, SMBA as AF
CRC
ADC3
PJ,PK[11:0]
SD_[A;B], SCK_[A;B], FS_[A;B],
MCLK_[A;B], D[3:1], CK[2:1] as AF
COMPx_INP, COMPx_INM,
COMPx_OUT as AF
HSEM
RX, TX, CTS, RTS, DE as AF
SPI2/I2S2
I2C2/SMBUS
RTC
Backup registers
LS
Up to 17 analog inputs
Some common to ADC1 and 2
TIM1/PWM
TIM8/PWM
AHB4 (275MHz)
CH[1:4]N, CH[1:4], ETR, BKIN, BKIN2
as AF
USART1
RX, TX, CTS, RTS, DE as AF
UART8
SPI3/I2S3
RAM
I/F
32-bit AHB BUS-MATRIX
APB4
MHz
(max)
APB4
138138
MHz
(max)
CH[1:4]N, CH[1:4], ETR, BKIN, BKIN2
as AF
DAP
RX, TX, CTS, RTS, DE as AF
UART7
FIFO
RX, TX, CK, CTS, RTS, DE as AF
BDMA
AHB4
RX, TX, CK, CTS, RTS, DE as AF
DMA
Mux2
RX, TX, CTS, RTS, DE as AF
UART5
I2C1/SMBUS
APB1 138MHz (max)
UART9
10 KB SRAM
SPI1/I2S1
AHB4
RX, TX, CTS, RTS, DE as AF
SPI4
AHB4_MEMD3 (275MHz)
MOSI, MISO, SCK, NSS /
SDO, SDI, CK, WS, MCK, as AF
AHB4 (275MHz)
MOSI, MISO, SCK, NSS as AF
TIM16
TIM15
RX, TX, CK, CTS, RTS, DE as A
UART4
Digital filter
2 compl. chan.(TIM15_CH1[1:2]N),
2 chan. (TIM_CH15[1:2], BKIN as AF
TIM17
AHB4
1 compl. chan.(TIM17_CH1N),
1 chan. (TIM17_CH1, BKIN as AF
1 compl. chan.(TIM16_CH1N),
1 chan. (TIM16_CH1, BKIN as AF
SPI5
APB2 138 MHz (max)
MOSI, MISO, SCK, NSS as AF
SAI1
AHB4
SD_[A;B], SCK_[A;B], FS_[A;B],
MCLK_[A;B], D[3:1], CK[2:1] as AF
DFSDM
APB4 138MHz (max)
CKOUT, DATIN[7:0], CKIN[7:0]
AWU
OSC32_IN
OSC32_OUT
TS, TAMP1, TAMP3,
OUT, REFIN
@VDD
XTAL OSC
4- 48 MHz
PLL1+PLL2+PLL3
OSC_IN
OSC_OUT
@VDD
POR
reset
Int
SUPPLY SUPERVISION
POR/PDR/BOR
PVD
VDDA, VSSA
NRESET
WKUP[1;2;4;6]
MSv52541V3
16/236
DS13314 Rev 3
STM32H733xG
Description
Table 1. STM32H733xG features and peripheral counts
Peripherals
Flash memory (Kbytes)
SRAM (Kbytes)
STM32H7
33VGH
STM32H7
33VGT
STM32H7
33ZGT
STM32H7
33ZGI
1024
1024
1024
1024
SRAM mapped onto AXI bus
128
SRAM1 (D2 domain)
16
SRAM2 (D2 domain)
16
SRAM4 (D3 domain)
16
RAM shared between ITCM and AXI (Kbytes)
192
ITCM RAM (instruction)
64
DTCM RAM (data)
128
TCM RAM (Kbytes)
Backup SRAM (Kbytes)
4
Interface
1
NOR Flash
memory/RAM
controller
-
-
yes
yes
Multiplexed I/O
NOR Flash
memory
yes
yes
yes
yes
16-bit NAND
Flash memory
yes
yes
yes
yes
16-bit SDRAM
controller
-
-
yes
yes
GPIO
80
80
112
114
Octo-SPI interface
1
1
2
2
FMC
OTFDEC
yes
CORDIC
yes
FMAC
yes
Timers
Wakeup pins
General purpose 32 bits
4
4
4
4
General purpose 16 bits
10
10
10
10
Advanced control
(PWM)
2
2
2
2
Basic
2
2
2
2
Low-power
5
5
5
5
RTC
1
1
1
1
Window watchdog /
independent watchdog
2
2
2
2
4
4
4
4
DS13314 Rev 3
17/236
53
Description
STM32H733xG
Table 1. STM32H733xG features and peripheral counts (continued)
Peripherals
Tamper pins
STM32H7
33VGH
STM32H7
33VGT
STM32H7
33ZGT
STM32H7
33ZGI
2
2
2
2
Random number generator
yes
Cryptographic accelerator
yes
SPI / I2S
5/4
5/4
6/4
6/4
5
5
5
5
USART/UART/
LPUART
5/5/1
5/5/1
5/5/1
5/5/1
SAI/PDM
2/1(1)
2/1(1)
2/1
2/1
I2C
Communication
interfaces
SPDIFRX
1
HDMI-CEC
1
SWPMI
1
MDIO
1
SDMMC
2
FDCAN/TT-FDCAN
2/1
2/1
2/1
2/1
USB [OTG_HS(ULPI)/FS(PHY)]
1 [1/1]
1 [1/1]
1 [1/1]
1 [1/1]
Ethernet [MII/RMII]
1 [1/1]
1 [1/1]
1 [1/1]
1 [1/1]
yes
yes
Camera interface/PSSI
LCD-TFT
yes
yes
yes
Chrom-ART Accelerator (DMA2D)
yes
Number of ADCs
16-bit ADCs
2
Number of direct
channelsADC1/ADC2
2/2
0
0
2/2
Number of fast channels
ADC1/ADC2
3/2
3/2
4/3
4/3
Number of slow channels
ADC1/ADC2
9/8
11/10
12/11
12/11
Number of ADCs
12-bit ADCs
1
Number of direct channels
2
2
2
2
Number of fast channels
6
2
6
6
Number of slow channels
9
0
4
9
Present in IC
12-bit DAC
DFSDM
18/236
yes
Number of channels
2
Comparators
2
Operational amplifiers
2
Present in IC
yes
DS13314 Rev 3
STM32H733xG
Description
Table 1. STM32H733xG features and peripheral counts (continued)
Peripherals
STM32H7
33VGH
STM32H7
33VGT
Maximum CPU frequency
USB separate supply pad
USB internal regulator
yes
-
yes
yes
-
-
-
-
-
-
yes
SMPS step-down converter
Operating voltage
Package
STM32H7
33ZGI
550 MHz
LDO
Operating
temperatures
STM32H7
33ZGT
-
-
1.62 to
3.6 V
1.71 to
3.6 V
1.62 to 3.6 V
Ambient temperature
-40°C to +85°C
Junction temperature
-40°C to +125°C
TFBGA100
LQFP100
LQFP144
UFBGA144
1. For limitations on peripheral features depending on packages, check the available pins/balls in Table 8: STM32H733 pin
alternate functions.
DS13314 Rev 3
19/236
53
Functional overview
STM32H733xG
3
Functional overview
3.1
Arm® Cortex®-M7 with FPU
The Arm® Cortex®-M7 with double-precision FPU processor is the latest generation of Arm
processors for embedded systems. It was developed to provide a low-cost platform that
meets the needs of MCU implementation, with a reduced pin count and optimized power
consumption, while delivering outstanding computational performance and low interrupt
latency.
The Cortex®-M7 processor is a highly efficient high-performance featuring:
•
Six-stage dual-issue pipeline
•
Dynamic branch prediction
•
Harvard architecture with L1 caches (32 Kbytes of I-cache and 32 Kbytes of D-cache)
•
64-bit AXI interface
•
64-bit ITCM interface
•
2x32-bit DTCM interfaces
The following memory interfaces are supported:
•
Separate Instruction and Data buses (Harvard Architecture) to optimize CPU latency
•
Tightly Coupled Memory (TCM) interface designed for fast and deterministic SRAM
accesses
•
AXI Bus interface to optimize Burst transfers
•
Dedicated low-latency AHB-Lite peripheral bus (AHBP) to connect to peripherals.
The processor supports a set of DSP instructions which allow efficient signal processing and
complex algorithm execution.
It also supports single and double precision FPU (floating point unit) speeds up software
development by using metalanguage development tools, while avoiding saturation.
Figure 1 shows the general block diagram of the STM32H733xG family.
3.2
Memory protection unit (MPU)
The memory protection unit (MPU) manages the CPU access rights and the attributes of the
system resources. It has to be programmed and enabled before use. Its main purposes are
to prevent an untrusted user program to accidentally corrupt data used by the OS and/or by
a privileged task, but also to protect data processes or read-protect memory regions.
The MPU defines access rules for privileged accesses and user program accesses. It
allows defining up to 16 protected regions that can in turn be divided into up to 8
independent subregions, where region address, size, and attributes can be configured. The
protection area ranges from 32 bytes to 4 Gbytes of addressable memory.
When an unauthorized access is performed, a memory management exception is
generated.
20/236
DS13314 Rev 3
STM32H733xG
Functional overview
3.3
Memories
3.3.1
Embedded Flash memory
The STM32H733xG devices embed 1 Mbyte of Flash memory that can be used for storing
programs and data.
The Flash memory is organized as 266-bit Flash words memory that can be used for storing
both code and data constants. Each word consists of:
•
one Flash word (8 words, 32 bytes or 256 bits)
•
10 ECC bits (single-error correction and double-error detection).
The Flash memory is organized as follows:
3.3.2
•
1 Mbyte of user Flash memory block containing eight user sectors of 128 Kbytes
(4 K Flash memory words)
•
128 Kbytes of system Flash memory from which the device can boot
•
2 Kbytes (64 Flash words) of user option bytes for user configuration
Embedded SRAM
All devices feature:
•
from 128 to 320 Kbytes of AXI-SRAM mapped onto the AXI bus on D1 domain
•
SRAM1 mapped on D2 domain: 16 Kbytes
•
SRAM2 mapped on D2 domain: 16 Kbytes
•
SRAM4 mapped on D3 domain: 16 Kbytes
•
4 Kbytes of backup SRAM
The content of this area is protected against possible unwanted write accesses, and
can be retained in Standby or VBAT mode.
•
RAM mapped to TCM interface (ITCM and DTCM):
Both ITCM and DTCM RAMs are 0 wait state memories. They can be accessed either
from the CPU or the MDMA (even in Sleep mode) through a specific AHB slave of the
Cortex®-M7CPU(AHBSAHBP):
–
64 to 256 Kbytes of ITCM-RAM (instruction RAM)
This RAM is connected to ITCM 64-bit interface designed for execution of critical
real-times routines by the CPU.
–
128 Kbytes of DTCM-RAM (2x 64-Kbyte DTCM-RAMs on 2x32-bit DTCM ports)
The DTCM-RAM could be used for critical real-time data, such as interrupt service
routines or stack/heap memory. Both DTCM-RAMs can be used in parallel (for
load/store operations) thanks to the Cortex®-M7 dual issue capability.
The MDMA can be used to load code or data in ITCM or DTCM RAMs. As reflected
above, 192 Kbyte of RAM can be used either for AXI SRAM or ITCM, with a 64Kbyte
granularity.
DS13314 Rev 3
21/236
53
Functional overview
STM32H733xG
Error code correction (ECC)
Over the product lifetime, and/or due to external events such as radiations, invalid bits in
memories may occur. They can be detected and corrected by ECC. This is an expected
behavior that has to be managed at final-application software level in order to ensure data
integrity through ECC algorithms implementation.
SRAM data are protected by ECC:
•
7 ECC bits are added per 32-bit word.
•
8 ECC bits are added per 64-bit word for AXI-SRAM and ITCM-RAM.
The ECC mechanism is based on the SECDED algorithm. It supports single-error correction
and double-error detection.
3.4
Secure access mode
In addition to other typical memory protection mechanism (RDP, PCROP), STM32H733xG
devices introduce the Secure access mode, a new enhanced security feature. This mode
allows developing user-defined secure services by ensuring, on the one hand code and
data protection and on the other hand code safe execution.
Two types of secure services are available:
•
STMicroelectronics Root Secure Services:
These services are embedded in System memory. They provide a secure solution for
firmware and third-party modules installation. These services rely on cryptographic
algorithms based on a device unique private key.
•
User-defined secure services:
These services are embedded in user Flash memory. Examples of user secure
services are proprietary user firmware update solution, secure Flash integrity check or
any other sensitive applications that require a high level of protection.
The secure firmware is embedded in specific user Flash memory areas configured
through option bytes.
Secure services are executed just after a reset and preempt all other applications to
guarantee protected and safe execution. Once executed, the corresponding code and data
are no more accessible.
The above secure services is activated for the next reset exits through an option bit.
22/236
DS13314 Rev 3
STM32H733xG
3.5
Functional overview
Boot modes
At startup, the boot memory space is selected by the BOOT pin and BOOT_ADDx option
bytes, allowing to program any boot memory address from 0x0000 0000 to 0x3FFF FFFF
which includes:
•
All Flash address space
•
All RAM address space: ITCM, DTCM RAMs and SRAMs
•
The System memory bootloader
The boot loader is located in non-user System memory. It is used to reprogram the Flash
memory through a serial interface (USART, I2C, SPI, FDCAN, USB-DFU). Refer to
application note AN2606 “STM32 microcontroller System memory Boot mode” for details.
3.6
CORDIC co-processor (CORDIC)
The CORDIC co-processor provides hardware acceleration of certain mathematical
functions, notably trigonometric, commonly used in motor control, metering, signal
processing and many other applications.
It speeds up the calculation of these functions compared to a software implementation,
allowing a lower operating frequency, or freeing up processor cycles in order to perform
other tasks.
The filter mathematical accelerator unit performs arithmetic operations on vectors. It
comprises a multiplier/accumulator (MAC) unit, together with address generation logic,
which allows it to index vector elements held in local memory.
The unit includes support for circular buffers on input and output, which allows digital filters
to be implemented. Both finite and infinite impulse response filters can be realized.
The unit allows frequent or lengthy filtering operations to be offloaded from the CPU, freeing
up the processor for other tasks. In many cases it can accelerate such calculations
compared to a software implementation, resulting in a speed-up of time critical tasks.
CORDIC features
•
24-bit CORDIC rotation engine
•
Circular and Hyperbolic modes
•
Rotation and Vectoring modes
•
Functions: Sine, Cosine, Sinh, Cosh, Atan, Atan2, Atanh, Modulus, Square root,
Natural logarithm
•
Programmable precision up to 20-bit
•
Fast convergence: 4 bits per clock cycle
•
Supports 16-bit and 32-bit fixed point input and output formats
•
Low latency AHB slave interface
•
Results can be read as soon as ready without polling or interrupt
•
DMA read and write channels
DS13314 Rev 3
23/236
53
Functional overview
3.7
STM32H733xG
Filter mathematical accelerator (FMAC)
The filter mathematical accelerator unit performs arithmetic operations on vectors. It
comprises a multiplier/accumulator (MAC) unit, together with address generation logic,
which allows it to index vector elements held in local memory.
The unit includes support for circular buffers on input and output, which allows digital filters
to be implemented. Both finite and infinite impulse response filters can be realized.
The unit allows frequent or lengthy filtering operations to be offloaded from the CPU, freeing
up the processor for other tasks. In many cases it can accelerate such calculations
compared to a software implementation, resulting in a speed-up of time critical tasks.
FMAC features
•
16 x 16-bit multiplier
•
24+2-bit accumulator with addition and subtraction
•
16-bit input and output data
•
256 x 16-bit local memory
•
Up to three areas can be defined in memory for data buffers (two input, one output),
defined by programmable base address pointers and associated size registers
•
Input and output sample buffers can be circular
•
Buffer “watermark” feature reduces overhead in interrupt mode
•
Filter functions: FIR, IIR (direct form 1)
•
AHB slave interface
•
DMA read and write data channels
3.8
Power supply management
3.8.1
Power supply scheme
STM32H733xG power supply voltages are the following:
24/236
•
VDD = 1.62 to 3.6 V: external power supply for I/Os, provided externally through VDD
pins.
•
VDDLDO = 1.62 to 3.6 V: supply voltage for the internal regulator supplying VCORE
•
VDDA = 1.62 to 3.6 V: external analog power supplies for ADC, DAC, COMP and
OPAMP.
•
VDD33USB: allows the support of a VDD supply different from 3.3 V while powering the
USB transceiver with 3.3V on VDD33USB.
•
VBAT = 1.2 to 3.6 V: power supply for the VSW domain when VDD is not present.
•
VCAP: VCORE supply voltage, which values depend on voltage scaling (1.0 V, 1.1 V,
1.2 V or 1.35 V). They are configured through VOS bits in PWR_D3CR register. The
VCORE domain is split into the following power domains that can be independently
switch off.
–
D1 domain containing some peripherals and the Cortex®-M7 core
–
D2 domain containing a large part of the peripherals
–
D3 domain containing some peripherals and the system control
DS13314 Rev 3
STM32H733xG
Functional overview
During power-up and power-down phases, the following power sequence requirements
must be respected (see Figure 2):
•
When VDD is below VDDmin, other power supplies (VDDA, VDD33USB) must remain
below VDD + 300 mV.
•
When VDD is above VDDmin, all power supplies are independent.
During the power-down phase, VDD can temporarily become lower than other supplies only
if the energy provided to the microcontroller remains below 1 mJ. This allows external
decoupling capacitors to be discharged with different time constants during the power-down
transient phase.
Figure 2. Power-up/power-down sequence
V
3.6
VDDX(1)
VDD
VBOR0
1
0.3
Power-on
Invalid supply area
Operating mode
VDDX < VDD + 300 mV
Power-down
time
VDDX independent from VDD
MSv47490V1
1. VDDx refers to any power supply among VDDA, VDD33USB.
3.8.2
Power supply supervisor
The devices have an integrated power-on reset (POR)/ power-down reset (PDR) circuitry
coupled with a Brownout reset (BOR) circuitry:
•
Power-on reset (POR)
The POR supervisor monitors VDD power supply and compares it to a fixed threshold.
The devices remain in Reset mode when VDD is below this threshold,
•
Power-down reset (PDR)
The PDR supervisor monitors VDD power supply. A reset is generated when VDD drops
below a fixed threshold.
The PDR supervisor can be enabled/disabled through PDR_ON pin.
•
Brownout reset (BOR)
The BOR supervisor monitors VDD power supply. Three BOR thresholds (from 2.1 to
2.7 V) can be configured through option bytes. A reset is generated when VDD drops
below this threshold.
DS13314 Rev 3
25/236
53
Functional overview
3.8.3
STM32H733xG
Voltage regulator
The same voltage regulator supplies the 3 power domains (D1, D2 and D3). D1 and D2 can
be independently switched off.
Voltage regulator output can be adjusted according to application needs through 6 power
supply levels:
•
•
3.9
Run mode (VOS0 to VOS3)
–
Scale 0: boosted performance
–
Scale 1: high performance
–
Scale 2: medium performance and consumption
–
Scale 3: optimized performance and low-power consumption
Stop mode (SVOS3 to SVOS5)
–
Scale 3: peripheral with wakeup from Stop mode capabilities (UART, SPI, I2C,
LPTIM) are operational
–
Scale 4 and 5 where the peripheral with wakeup from Stop mode is disabled. The
peripheral functionality is disabled but wakeup from Stop mode is possible through
GPIO or asynchronous interrupt.
Low-power strategy
There are several ways to reduce power consumption on STM32H733xG:
•
Decrease the dynamic power consumption by slowing down the system clocks even in
Run mode and by individually clock gating the peripherals that are not used.
•
Save power when the CPU is idle, by selecting among the available low-power modes
according to the user application needs. This allows the best compromise between
short startup time and low power consumption to be achieved, according to the
available wakeup sources.
The devices feature several low-power modes:
•
CSleep (CPU clock stopped)
•
CStop (CPU sub-system clock stopped)
•
DStop (Domain bus matrix clock stopped)
•
Stop (System clock stopped)
•
DStandby (Domain powered down)
•
Standby (System powered down)
CSleep and CStop low-power modes are entered by the MCU when executing the WFI
(Wait for Interrupt) or WFE (Wait for Event) instructions, or when the SLEEPONEXIT bit of
the Cortex®-Mx core is set after returning from an interrupt service routine.
A domain can enter low-power mode (DStop or DStandby) when the processor, its
subsystem and the peripherals allocated in the domain enter low-power mode.
If part of the domain is not in low-power mode, the domain remains in the current mode.
Finally the system can enter Stop or Standby when all EXTI wakeup sources are cleared
and the power domains are in DStop or DStandby mode.
26/236
DS13314 Rev 3
STM32H733xG
Functional overview
Table 2. System versus domain low-power mode
System power mode
D1 domain power mode
D2 domain power mode
D3 domain power mode
Run
DRun/DStop/DStandby
DRun/DStop/DStandby
DRun
Stop
DStop/DStandby
DStop/DStandby
DStop
Standby
DStandby
DStandby
DStandby
3.10
Reset and clock controller (RCC)
The clock and reset controller is located in D3 domain. The RCC manages the generation of
all the clocks, as well as the clock gating and the control of the system and peripheral
resets. It provides a high flexibility in the choice of clock sources and allows to apply clock
ratios to improve the power consumption. In addition, on some communication peripherals
that are capable to work with two different clock domains (either a bus interface clock or a
kernel peripheral clock), thus the system frequency can be changed without modifying the
baudrate.
3.10.1
Clock management
The devices embed four internal oscillators, two oscillators with external crystal or
resonator, two internal oscillators with fast startup time and three PLLs.
The RCC receives the following clock source inputs:
•
•
Internal oscillators:
–
64 MHz HSI clock
–
48 MHz RC oscillator
–
4 MHz CSI clock
–
32 kHz LSI clock
External oscillators:
–
HSE clock: 4-50 MHz (generated from an external source) or 4-48 MHz(generated
from a crystal/ceramic resonator)
–
LSE clock: 32.768 kHz
The RCC provides three PLLs: one for system clock, two for kernel clocks.
The system starts on the HSI clock. The user application can then select the clock
configuration.
DS13314 Rev 3
27/236
53
Functional overview
3.10.2
STM32H733xG
System reset sources
Power-on reset initializes all registers while system reset reinitializes the system except for
the debug, part of the RCC and power controller status registers, as well as the backup
power domain.
A system reset is generated in the following cases:
3.11
•
Power-on reset (pwr_por_rst)
•
Brownout reset
•
Low level on NRST pin (external reset)
•
Window watchdog
•
Independent watchdog
•
Software reset
•
Low-power mode security reset
•
Exit from Standby
General-purpose input/outputs (GPIOs)
Each of the GPIO pins can be configured by software as output (push-pull or open-drain,
with or without pull-up or pull-down), as input (floating, with or without pull-up or pull-down)
or as peripheral alternate function. Most of the GPIO pins are shared with digital or analog
alternate functions. All GPIOs are high-current-capable and have speed selection to better
manage internal noise, power consumption and electromagnetic emission.
After reset, all GPIOs (except debug pins) are in Analog mode to reduce power
consumption (refer to GPIOs register reset values in the device reference manual).
The I/O configuration can be locked if needed by following a specific sequence in order to
avoid spurious writing to the I/Os registers.
3.12
Bus-interconnect matrix
The devices feature an AXI bus matrix, two AHB bus matrices and bus bridges that allow
the interconnection of bus masters with bus slaves (see Figure 3).
28/236
DS13314 Rev 3
STM32H733xG
Figure 3. STM32H733xG bus matrix
AHBS
OR
DMA2D
LTDC
D1-to-D2 AHB
DMA2_MEM
MDMA
DMA1_MEM
SDMMC1
DMA2
Ethernet SDMMC2 USBHS1
MAC
DMA2_PERIPH
DMA1
AHBP
AXIM
I$
D$
32KB 32KB
ITCM
64 Kbyte
ITCM
192 Kbyte
DTCM
128 Kbyte
DMA1_PERIPH
CPU
Cortex-M7
AXI SRAM
192K byte
SRAM1 16
Kbyte
SRAM2 16
Kbyte
Flash A
Up to 1 Mbyte
AHB1
DS13314 Rev 3
AXI SRAM
128 Kbyte
OTFDEC1
OCTOSPI1
OTFDEC2
OCTOSPI2
AHB2
APB1
FMC
AHB3
APB2
APB3
64-bit AXI bus matrix
D1 domain
32-bit AHB bus matrix
D2 domain
D2-to-D1 AHB
D2-to-D3 AHB
D1-to-D3 AHB
BDMA
Legend
32-bit bus
AHB4
TCM AHB
AXI
APB
29/236
64-bit bus
Master interface
Bus multiplexer
Slave interface
APB4
SRAM4
16 Kbyte
Backup
SRAM
4 Kbyte
MSv46613V3
Functional overview
32-bit AHB bus matrix
D3 domain
Functional overview
3.13
STM32H733xG
DMA controllers
The devices feature four DMA instances and a DMA request router to unload CPU activity:
•
A master direct memory access (MDMA)
The MDMA is a high-speed DMA controller, which is in charge of all types of memory
transfers (peripheral to memory, memory to memory, memory to peripheral), without
any CPU action. It features a master AXI interface and a dedicated AHB interface to
access Cortex®-M7 TCM memories.
The MDMA is located in D1 domain. It is able to interface with the other DMA
controllers located in D2 domain to extend the standard DMA capabilities, or can
manage peripheral DMA requests directly.
Each of the 16 channels can perform single block transfers, repeated block transfers
and linked list transfers.
•
Two dual-port DMAs (DMA1, DMA2) located in D2 domain, with FIFO and request
router capabilities.
•
One basic DMA (BDMA) located in D3 domain, with request router capabilities.
•
A DMA request multiplexer (DMAMUX)
The DMA request router could be considered as an extension of the DMA controller. It
routes the DMA peripheral requests to the DMA controller itself. This allowing
managing the DMA requests with a high flexibility, maximizing the number of DMA
requests that run concurrently, as well as generating DMA requests from peripheral
output trigger or DMA event.
3.14
Chrom-ART Accelerator (DMA2D)
The Chrom-Art Accelerator (DMA2D) is a specialized DMA dedicated to image manipulation.
It can perform the following operations:
•
Filling a part or the whole of a destination image with a specific color
•
Copying a part or the whole of a source image into a part or the whole of a destination
•
image
•
Copying a part or the whole of a source image into a part or the whole of a destination
•
image with a pixel format conversion
•
Blending a part and/or two complete source images with different pixel format and copy
•
the result into a part or the whole of a destination image with a different color format.
•
All the classical color coding schemes are supported from 4-bit up to 32-bit per pixel
with indexed or direct color mode, including block based YCbCr to handle JPEG
decoder output.
•
The DMA2D has its own dedicated memories for CLUTs (color look-up tables).
An interrupt can be generated when an operation is complete or at a programmed
watermark.
All the operations are fully automated and are running independently from the CPU or the
DMAs.
30/236
DS13314 Rev 3
STM32H733xG
3.15
Functional overview
Nested vectored interrupt controller (NVIC)
The devices embed a nested vectored interrupt controller which is able to manage 16
priority levels, and handle up to 140 maskable interrupt channels plus the 16 interrupt lines
of the Cortex®-M7 with FPU core.
•
Closely coupled NVIC gives low-latency interrupt processing
•
Interrupt entry vector table address passed directly to the core
•
Allows early processing of interrupts
•
Processing of late arriving, higher-priority interrupts
•
Support tail chaining
•
Processor context automatically saved on interrupt entry, and restored on interrupt exit
with no instruction overhead
This hardware block provides flexible interrupt management features with minimum interrupt
latency.
3.16
Extended interrupt and event controller (EXTI)
The EXTI controller performs interrupt and event management. In addition, it can wake up
the processor, power domains and/or D3 domain from Stop mode.
The EXTI handles up to 80 independent event/interrupt lines split as 26 configurable events
and 54 direct events.
Configurable events have dedicated pending flags, active edge selection, and software
trigger capable.
Direct events provide interrupts or events from peripherals having a status flag.
3.17
Cyclic redundancy check calculation unit (CRC)
The CRC (cyclic redundancy check) calculation unit is used to get a CRC code using a
programmable polynomial.
Among other applications, CRC-based techniques are used to verify data transmission or
storage integrity. In the scope of the EN/IEC 60335-1 standard, they offer a means of
verifying the Flash memory integrity. The CRC calculation unit helps compute a signature of
the software during runtime, to be compared with a reference signature generated at linktime and stored at a given memory location.
DS13314 Rev 3
31/236
53
Functional overview
3.18
STM32H733xG
Flexible memory controller (FMC)
The FMC controller main features are the following:
•
Interface with static-memory mapped devices including:
3.19
–
Static random access memory (SRAM)
–
NOR Flash memory/OneNAND Flash memory
–
PSRAM (4 memory banks)
–
NAND Flash memory with ECC hardware to check up to 8 Kbytes of data
•
Interface with synchronous DRAM (SDRAM/Mobile LPSDR SDRAM) memories
•
8-,16-bit data bus width
•
Independent Chip Select control for each memory bank
•
Independent configuration for each memory bank
•
Write FIFO
•
Read FIFO for SDRAM controller
•
The maximum FMC_CLK/FMC_SDCLK frequency for synchronous accesses is the
FMC kernel clock divided by 2.
Octo-SPI memory interface (OCTOSPI)
The OCTOSPI is a specialized communication interface targeting single, dual, quad or octal
SPI memories. The STM32H733xG embeds two separate Octo-SPI interfaces.
Each OCTOSPI instance supports single/dual/quad/octal SPI formats. multiplexing of
single/dual/quad/octal SPI over the same bus can be achieved using the integrated OctoSPI I/O manager (OCTOSPIM).
The OCTOSPI can operate in any of the three following modes:
•
Indirect mode: all the operations are performed using the OCTOSPI registers
•
Status-polling mode: the external memory status register is periodically read and an
interrupt can be generated in case of flag setting
•
Memory-mapped mode: the external memory is memory mapped and it is seen by the
system as if it was an internal memory supporting both read and write operations.
The OCTOSPI supports two frame formats supported by most external serial memories
such as serial PSRAMs, serial NAND and serial NOR Flash memories, Hyper RAMs and
Hyper Flash memories.
Multi chip package (MCP) combining any of the above mentioned memory types can also
be supported.
32/236
•
The classical frame format with the command, address, alternate byte, dummy cycles
and data phase
•
The HyperBus™ frame format.
DS13314 Rev 3
STM32H733xG
3.20
Functional overview
Analog-to-digital converters (ADCs)
STM32H733xG devices embed three analog-to-digital converters, two of 16-bit resolution,
and the third of 12-bit resolution. The 16-bit resolution ADCs can be configured as 16, 14,
12, 10 or 8 bits. The 12-bit resolution ADC can be configured to 12, 10 or 8 bits.
Each ADC shares up to 20 external channels, performing conversions in Single-shot or
Scan mode. In Scan mode, automatic conversion is performed on a selected group of
analog inputs.
Additional logic functions embedded in the ADC interface allow:
•
simultaneous sample and hold
•
Interleaved sample and hold
The ADC can be served by the DMA controller, thus allowing automatic transfer of ADC
converted values to a destination location without any software action.
In addition, an analog watchdog feature can accurately monitor the converted voltage of
one, some, or all selected channels. An interrupt is generated when the converted voltage is
outside the programmed thresholds.
To synchronize A/D conversion and timers, the ADCs can be triggered by any of the TIM1,
TIM2, TIM3, TIM4, TIM6, TIM8, TIM15, TIM23, TIM24, and LPTIM1 timers.
3.21
Temperature sensor
STM32H733xG devices embed a temperature sensor that generates a voltage (VTS) that
varies linearly with the temperature. This temperature sensor is internally connected to
ADC3_IN17. The conversion range is between 1.7 V and 3.6 V. It can measure the device
junction temperature ranging from − 40 to +125°C.
The temperature sensor have a good linearity, but it has to be calibrated to obtain a good
overall accuracy of the temperature measurement. As the temperature sensor offset varies
from chip to chip due to process variation, the uncalibrated internal temperature sensor is
suitable for applications that detect temperature changes only. To improve the accuracy of
the temperature sensor measurement, each device is individually factory-calibrated by ST.
The temperature sensor factory calibration data are stored by ST in the System memory
area, which is accessible in Read-only mode.
3.22
Digital temperature sensor (DTS)
STM32H733xG devices embed a sensor that converts the temperature into a square wave
the frequency of which is proportional to the temperature. The PCLK or the LSE clock can
be used as the reference clock for the measurements. A formula given in the product
reference manual allows calculation of the temperature according to the measured
frequency stored in the DTS_DR register.
DS13314 Rev 3
33/236
53
Functional overview
3.23
STM32H733xG
VBAT operation
The VBAT power domain contains the RTC, the backup registers and the backup SRAM.
To optimize battery duration, this power domain is supplied by VDD when available or by the
voltage applied on VBAT pin (when VDD supply is not present). VBAT power is switched
when the PDR detects that VDD dropped below the PDR level.
The voltage on the VBAT pin could be provided by an external battery, a supercapacitor or
directly by VDD, in which case, the VBAT mode is not functional.
VBAT operation is activated when VDD is not present.
The VBAT pin supplies the RTC, the backup registers and the backup SRAM.
Note:
When the microcontroller is supplied from VBAT, external interrupts and RTC alarm/events
do not exit it from VBAT operation.
When PDR_ON pin is connected to VSS (Internal Reset OFF), the VBAT functionality is no
more available and VBAT pin should be connected to VDD.
3.24
Digital-to-analog converters (DAC)
The two 12-bit buffered DAC channels can be used to convert two digital signals into two
analog voltage signal outputs.
This dual digital Interface supports the following features:
•
two DAC converters: one for each output channel
•
8-bit or 12-bit monotonic output
•
left or right data alignment in 12-bit mode
•
synchronized update capability
•
noise-wave generation
•
triangular-wave generation
•
dual DAC channel independent or simultaneous conversions
•
DMA capability for each channel including DMA underrun error detection
•
external triggers for conversion
•
input voltage reference VREF+ or internal VREFBUF reference.
The DAC channels are triggered through the timer update outputs that are also connected
to different DMA streams.
34/236
DS13314 Rev 3
STM32H733xG
3.25
Functional overview
Ultra-low-power comparators (COMP)
STM32H733xG devices embed two rail-to-rail comparators (COMP1 and COMP2). They
feature programmable reference voltage (internal or external), hysteresis and speed (low
speed for low-power) as well as selectable output polarity.
The reference voltage can be one of the following:
•
An external I/O
•
A DAC output channel
•
An internal reference voltage or submultiple (1/4, 1/2, 3/4).
All comparators can wake up from Stop mode, generate interrupts and breaks for the timers,
and be combined into a window comparator.
3.26
Operational amplifiers (OPAMP)
STM32H733xG devices embed two rail-to-rail operational amplifiers (OPAMP1 and
OPAMP2) with external or internal follower routing and PGA capability.
The operational amplifier main features are:
•
PGA with a non-inverting gain ranging of 2, 4, 8 or 16 or inverting gain ranging of -1, -3,
-7 or -15
•
One positive input connected to DAC
•
Output connected to internal ADC
•
Low input bias current down to 1 nA
•
Low input offset voltage down to 1.5 mV
•
Gain bandwidth up to 7.3 MHz
The devices embeds two operational amplifiers (OPAMP1 and OPAMP2) with two inputs
and one output each. These three I/Os can be connected to the external pins, thus enabling
any type of external interconnections. The operational amplifiers can be configured
internally as a follower, as an amplifier with a non-inverting gain ranging from 2 to 16 or with
inverting gain ranging from -1 to -15.
DS13314 Rev 3
35/236
53
Functional overview
3.27
STM32H733xG
Digital filter for sigma-delta modulators (DFSDM)
The devices embed one DFSDM with 4 digital filters modules and 8 external input serial
channels (transceivers) or alternately 8 internal parallel inputs support.
The DFSDM peripheral is dedicated to interface the external Σ∆ modulators to
microcontroller and then to perform digital filtering of the received data streams (which
represent analog value on Σ∆ modulators inputs). DFSDM can also interface PDM (Pulse
Density Modulation) microphones and perform PDM to PCM conversion and filtering in
hardware. DFSDM features optional parallel data stream inputs from internal ADC
peripherals or microcontroller memory (through DMA/CPU transfers into DFSDM).
DFSDM transceivers support several serial interface formats (to support various Σ∆
modulators). DFSDM digital filter modules perform digital processing according user
selected filter parameters with up to 24-bit final ADC resolution.
The DFSDM peripheral supports:
•
•
8 multiplexed input digital serial channels:
–
configurable SPI interface to connect various SD modulator(s)
–
configurable Manchester coded 1 wire interface support
–
PDM (Pulse Density Modulation) microphone input support
–
maximum input clock frequency up to 20 MHz (10 MHz for Manchester coding)
–
clock output for SD modulator(s): 0..20 MHz
alternative inputs from 8 internal digital parallel channels (up to 16 bit input resolution):
–
•
–
Sincx filter: filter order/type (1..5), oversampling ratio (up to 1..1024)
–
integrator: oversampling ratio (1..256)
•
up to 24-bit output data resolution, signed output data format
•
automatic data offset correction (offset stored in register by user)
•
continuous or single conversion
•
start-of-conversion triggered by:
•
•
•
36/236
internal sources: ADC data or memory data streams (DMA)
4 digital filter modules with adjustable digital signal processing:
–
software trigger
–
internal timers
–
external events
–
start-of-conversion synchronously with first digital filter module (DFSDM0)
analog watchdog feature:
–
low value and high value data threshold registers
–
dedicated configurable Sincx digital filter (order = 1..3, oversampling ratio = 1..32)
–
input from final output data or from selected input digital serial channels
–
continuous monitoring independently from standard conversion
short circuit detector to detect saturated analog input values (bottom and top range):
–
up to 8-bit counter to detect 1..256 consecutive 0’s or 1’s on serial data stream
–
monitoring continuously each input serial channel
break signal generation on analog watchdog event or on short circuit detector event
DS13314 Rev 3
STM32H733xG
•
Functional overview
extremes detector:
–
storage of minimum and maximum values of final conversion data
–
refreshed by software
•
DMA capability to read the final conversion data
•
interrupts: end of conversion, overrun, analog watchdog, short circuit, input serial
channel clock absence
•
“regular” or “injected” conversions:
•
–
“regular” conversions can be requested at any time or even in Continuous mode
without having any impact on the timing of “injected” conversions
–
“injected” conversions for precise timing and with high conversion priority
Pulse skipper feature to support beamforming applications (delay-line like behavior).
Table 3. DFSDM implementation
DFSDM features
DFSDM1
Number of filters
4
Number of input
transceivers/channels
8
Internal ADC parallel input
X
Number of external triggers
16
Regular channel information in
identification register
X
DS13314 Rev 3
37/236
53
Functional overview
3.28
STM32H733xG
Digital camera interface (DCMI)
The devices embed a camera interface that can connect with camera modules and CMOS
sensors through an 8-bit to 14-bit parallel interface, to receive video data. The camera
interface can achieve a data transfer rate up to 140 Mbyte/s using a 80 MHz pixel clock. It
features:
3.29
•
Programmable polarity for the input pixel clock and synchronization signals
•
Parallel data communication can be 8-, 10-, 12- or 14-bit
•
Supports 8-bit progressive video monochrome or raw bayer format, YCbCr 4:2:2
progressive video, RGB 565 progressive video or compressed data (like JPEG)
•
Supports Continuous mode or Snapshot (a single frame) mode
•
Capability to automatically crop the image
PSSI
The PSSI is a generic synchronous 8-/16-bit parallel data input/output slave interface. It
allows the transmitter to send a data valid signal to indicate when the data is valid, and the
receiver to output a flow control signal to indicate when it is ready to sample the data.
The main PSSI features are:
•
Slave mode operation
•
8- or 16-bit parallel data input or output
•
8-word (32-byte) FIFO
•
Data enable (DE) alternate function input and Ready (RDY) alternate function output.
When enabled, these signals can either allow the transmitter to indicate when the data is
valid or, the receiver to indicate when it is ready to sample the data, or both.
The PSSI shares most of its circuitry with the digital camera interface (DCMI). It therefore
cannot be used simultaneously with the DCMI.
3.30
LCD-TFT controller
The LCD-TFT display controller provides a 24-bit parallel digital RGB (Red, Green, Blue)
and delivers all signals to interface directly to a broad range of LCD and TFT panels up to
XGA (1024 x 768) resolution with the following features:
38/236
•
2 display layers with dedicated FIFO (64x64-bit)
•
Color Look-Up table (CLUT) up to 256 colors (256x24-bit) per layer
•
Up to 8 input color formats selectable per layer
•
Flexible blending between two layers using alpha value (per pixel or constant)
•
Flexible programmable parameters for each layer
•
Color keying (transparency color)
•
Up to 4 programmable interrupt events
•
AXI master interface with burst of 16 words
DS13314 Rev 3
STM32H733xG
3.31
Functional overview
True random number generator (RNG)
The RNG is a true random number generator that provides full entropy outputs to the
application as 32-bit samples. It is composed of a live entropy source (analog) and an
internal conditioning component.
The RNG can be used to construct a Non-deterministic Random Bit Generator (NDRBG), as
a NIST SP 800-90B compliant entropy source.
The RNG true random number generator has been tested using German BSI statistical tests
of AIS-31 (T0 to T8), and NIST SP800-90B statistical test suite.
3.32
Cryptographic acceleration (CRYP and HASH)
The devices embed a cryptographic processor that supports the advanced cryptographic
algorithms usually required to ensure confidentiality, authentication, data integrity and nonrepudiation when exchanging messages
with a peer:
•
•
Encryption/Decryption
–
DES/TDES (data encryption standard/triple data encryption standard): ECB
(electronic codebook) and CBC (cipher block chaining) chaining algorithms, 64-,
128- or 192-bit key
–
AES (advanced encryption standard): ECB, CBC, GCM, CCM, and CTR (counter
mode) chaining algorithms, 128, 192 or 256-bit key
Universal HASH
–
– SHA-1 and SHA-2 (secure HASH algorithms)
–
– MD5
–
– HMAC
The cryptographic accelerator supports DMA request generation.
3.33
On-the-fly decryption engine (OTFDEC)
The embedded OTFDEC decrypts in real-time the encrypted content stored in the external
Octo-SPI memories used in Memory-mapped mode.
The OTFDEC uses the AES-128 algorithm in counter mode (CTR).
Code execution on external Octo-SPI memories can be protected against fault injection
thanks to
STMicroelectronics enhanced encryption mode (refer to RM0468 for details).
DS13314 Rev 3
39/236
53
Functional overview
STM32H733xG
The OTFDEC main features are as follow:
•
•
–
AES-CTR algorithm with keystream FIFO (depth= 4)
–
Support for any read size
Up to four independent encrypted regions
–
Region definition granularity: 4096 bytes
–
Region configuration write locking mechanism
–
Two optional decryption modes: execute-only and execute-never
•
128-bit key for each region, two-byte firmware version, and eight-byte applicationdefined nonce
•
Encryption keys confidentiality and integrity protection
•
40/236
On-the-fly 128-bit decryption during STM32 Octo-SPI read operations (single or
multiple).
–
Write only registers with software locking mechanism
–
Availability of 8-bit CRC as public key information
Support for STM32 Octo-SPI prefetching mechanism.
DS13314 Rev 3
STM32H733xG
3.34
Functional overview
Timers and watchdogs
The devices include two advanced-control timers, twelve general-purpose timers, two basic
timers, five low-power timers, two watchdogs and a SysTick timer.
All timer counters can be frozen in Debug mode.
Table 4 compares the features of the advanced-control, general-purpose and basic timers.
Table 4. Timer feature comparison
Timer
type
Advanced
-control
Timer
TIM1,
TIM8
TIM2,
TIM5,
TIM23,
TIM24
TIM3,
TIM4
TIM12
DMA
Capture/
Counter Counter Prescaler
request
compare
resolution
type
factor
generation channels
TIM15
TIM16,
TIM17
Max
interface
clock
(MHz)
Max
timer
clock
(MHz)
(1)
16-bit
Any
Up,
integer
Down, between 1
Up/down
and
65536
Yes
4
Yes
137.5
275
32-bit
Any
Up,
integer
Down, between 1
Up/down
and
65536
Yes
4
No
137.5
275
16-bit
Any
Up,
integer
Down, between 1
Up/down
and
65536
Yes
4
No
137.5
275
16-bit
Up
Any
integer
between 1
and
65536
No
2
No
137.5
275
Up
Any
integer
between 1
and
65536
No
1
No
137.5
275
Up
Any
integer
between 1
and
65536
Yes
2
1
137.5
275
Up
Any
integer
between 1
and
65536
Yes
1
1
137.5
275
General
purpose
TIM13,
TIM14
Complementary
output
16-bit
16-bit
16-bit
DS13314 Rev 3
41/236
53
Functional overview
STM32H733xG
Table 4. Timer feature comparison (continued)
Timer
type
Timer
DMA
Capture/
Counter Counter Prescaler
request
compare
resolution
type
factor
generation channels
Basic
TIM6,
TIM7
16-bit
Up
Any
integer
between 1
and
65536
Lowpower
timer
LPTIM1,
LPTIM2,
LPTIM3,
LPTIM4,
LPTIM5
16-bit
Up
1, 2, 4, 8,
16, 32,
64, 128
Complementary
output
Max
interface
clock
(MHz)
Max
timer
clock
(MHz)
(1)
Yes
0
No
137.5
275
No
0
No
137.5
275
1. The maximum timer clock is up to 550 MHz depending on theTIMPRE bit in the RCC_CFGR register and D2PRE1/2 bits in
RCC_D2CFGR register.
42/236
DS13314 Rev 3
STM32H733xG
3.34.1
Functional overview
Advanced-control timers (TIM1, TIM8)
The advanced-control timers (TIM1, TIM8) can be seen as three-phase PWM generators
multiplexed on 6 channels. They have complementary PWM outputs with programmable
inserted dead times. They can also be considered as complete general-purpose timers.
Their 4 independent channels can be used for:
•
Input capture
•
Output compare
•
PWM generation (Edge- or Center-aligned modes)
•
One-pulse mode output
If configured as standard 16-bit timers, they have the same features as the general-purpose
TIMx timers. If configured as 16-bit PWM generators, they have full modulation capability (0100%).
The advanced-control timer can work together with the TIMx timers via the Timer Link
feature for synchronization or event chaining.
TIM1 and TIM8 support independent DMA request generation.
3.34.2
General-purpose timers (TIMx)
There are ten synchronizable general-purpose timers embedded in the STM32H733xG
devices (see Table 4: Timer feature comparison for differences).
•
TIM2, TIM3, TIM4, TIM5, TIM23, TIM24
The devices include 4 full-featured general-purpose timers: TIM2, TIM3, TIM4, TIM5,
TIM23 and TIM24. TIM2, TIM5, TIM23 and TIM24 are based on a 32-bit auto-reload
up/downcounter and a 16-bit prescaler while TIM3 and TIM4 are based on a 16-bit
auto-reload up/downcounter and a 16-bit prescaler. All timers feature 4 independent
channels for input capture/output compare, PWM or One-pulse mode output. This
gives up to 24 input capture/output compare/PWMs on the largest packages.
TIM2, TIM3, TIM4, TIM5, TIM23 and TIM24 general-purpose timers can work together,
or with the other general-purpose timers and the advanced-control timers TIM1 and
TIM8 via the Timer Link feature for synchronization or event chaining.
Any of these general-purpose timers can be used to generate PWM outputs.
TIM2, TIM3, TIM4, TIM5, TIM23, and TIM24 all have independent DMA request
generation. They are capable of handling quadrature (incremental) encoder signals
and the digital outputs from 1 to 4 hall-effect sensors.
•
TIM12, TIM13, TIM14, TIM15, TIM16, TIM17
These timers are based on a 16-bit auto-reload upcounter and a 16-bit prescaler.
TIM13, TIM14, TIM16 and TIM17 feature one independent channel, whereas TIM12
and TIM15 have two independent channels for input capture/output compare, PWM or
One-pulse mode output. They can be synchronized with the TIM2, TIM3, TIM4, TIM5,
TIM23, and TIM24 full-featured general-purpose timers or used as simple time bases.
DS13314 Rev 3
43/236
53
Functional overview
3.34.3
STM32H733xG
Basic timers TIM6 and TIM7
These timers are mainly used for DAC trigger and waveform generation. They can also be
used as a generic 16-bit time base.
TIM6 and TIM7 support independent DMA request generation.
3.34.4
Low-power timers (LPTIM1, LPTIM2, LPTIM3, LPTIM4, LPTIM5)
The low-power timers have an independent clock and is running also in Stop mode if it is
clocked by LSE, LSI or an external clock. It is able to wakeup the devices from Stop mode.
This low-power timer supports the following features:
3.34.5
•
16-bit up counter with 16-bit autoreload register
•
16-bit compare register
•
Configurable output: pulse, PWM
•
Continuous / One-shot mode
•
Selectable software / hardware input trigger
•
Selectable clock source:
•
Internal clock source: LSE, LSI, HSI or APB clock
•
External clock source over LPTIM input (working even with no internal clock source
running, used by the Pulse Counter Application)
•
Programmable digital glitch filter
•
Encoder mode
Independent watchdog
The independent watchdog is based on a 12-bit downcounter and 8-bit prescaler. It is
clocked from an independent 32 kHz internal RC and as it operates independently from the
main clock, it can operate in Stop and Standby modes. It can be used either as a watchdog
to reset the device when a problem occurs, or as a free-running timer for application timeout
management. It is hardware- or software-configurable through the option bytes.
A window option allows the device to be reset when a reload operation is made too early
after the previous reload.
3.34.6
Window watchdog
The window watchdog is based on a 7-bit downcounter that can be set as free-running. It
can be used as a watchdog to reset the device when a problem occurs. It is clocked from
the main clock. It has an early warning interrupt capability and the counter can be frozen in
Debug mode.
3.34.7
SysTick timer
This timer is dedicated to real-time operating systems, but could also be used as a standard
down counter. It features:
44/236
•
A 24-bit down counter
•
Autoreload capability
•
Maskable system interrupt generation when the counter reaches 0
•
Programmable clock source.
DS13314 Rev 3
STM32H733xG
3.35
Functional overview
Real-time clock (RTC), backup SRAM and backup registers
The RTC is an independent BCD timer/counter. It supports the following features:
•
Calendar with subsecond, seconds, minutes, hours (12 or 24 format), week day, date,
month, year, in BCD (binary-coded decimal) format.
•
Automatic correction for 28, 29 (leap year), 30, and 31 days of the month.
•
Two programmable alarms.
•
On-the-fly correction from 1 to 32767 RTC clock pulses. This can be used to
synchronize it with a master clock.
•
Reference clock detection: a more precise second source clock (50 or 60 Hz) can be
used to enhance the calendar precision.
•
Digital calibration circuit with 0.95 ppm resolution, to compensate for quartz crystal
inaccuracy.
•
Three anti-tamper detection pins with programmable filter.
•
Timestamp feature which can be used to save the calendar content. This function can
be triggered by an event on the timestamp pin, or by a tamper event, or by a switch to
VBAT mode.
•
17-bit auto-reload wakeup timer (WUT) for periodic events with programmable
resolution and period.
The RTC and the 32 backup registers are supplied through a switch that takes power either
from the VDD supply when present or from the VBAT pin.
The backup registers are 32-bit registers used to store 128 bytes of user application data
when VDD power is not present. They are not reset by a system or power reset, or when the
device wakes up from Standby mode.
The RTC clock sources can be:
•
A 32.768 kHz external crystal (LSE)
•
An external resonator or oscillator (LSE)
•
The internal low-power RC oscillator (LSI, with typical frequency of 32 kHz)
•
The high-speed external clock (HSE) divided by 32.
The RTC is functional in VBAT mode and in all low-power modes when it is clocked by the
LSE. When clocked by the LSI, the RTC is not functional in VBAT mode, but is functional in
all low-power modes.
All RTC events (Alarm, Wakeup Timer, Timestamp or Tamper) can generate an interrupt and
wakeup the device from the low-power modes.
DS13314 Rev 3
45/236
53
Functional overview
3.36
STM32H733xG
Inter-integrated circuit interface (I2C)
STM32H733xG devices embed five I2C interfaces.
The I2C bus interface handles communications between the microcontroller and the serial
I2C bus. It controls all I2C bus-specific sequencing, protocol, arbitration and timing.
The I2C peripheral supports:
•
•
3.37
I2C-bus specification and user manual rev. 5 compatibility:
–
Slave and Master modes, multimaster capability
–
Standard-mode (Sm), with a bitrate up to 100 kbit/s
–
Fast-mode (Fm), with a bitrate up to 400 kbit/s
–
Fast-mode Plus (Fm+), with a bitrate up to 1 Mbit/s and 20 mA output drive I/Os
–
7-bit and 10-bit addressing mode, multiple 7-bit slave addresses
–
Programmable setup and hold times
–
Optional clock stretching
System Management Bus (SMBus) specification rev 2.0 compatibility:
–
Hardware PEC (Packet Error Checking) generation and verification with ACK
control
–
Address resolution protocol (ARP) support
–
SMBus alert
•
Power System Management Protocol (PMBusTM) specification rev 1.1 compatibility
•
Independent clock: a choice of independent clock sources allowing the I2C
communication speed to be independent from the PCLK reprogramming.
•
Wakeup from Stop mode on address match
•
Programmable analog and digital noise filters
•
1-byte buffer with DMA capability
Universal synchronous/asynchronous receiver transmitter
(USART)
STM32H733xG devices have five embedded universal synchronous receiver transmitters
(USART1, USART2, USART3, USART6, and USART10) and five universal asynchronous
receiver transmitters (UART4, UART5, UART7, UART8, and UART9). Refer to Table 5:
USART features for a summary of USARTx and UARTx features.
These interfaces provide asynchronous communication, IrDA SIR ENDEC support,
multiprocessor communication mode, single-wire Half-duplex communication mode and
have LIN Master/Slave capability. They provide hardware management of the CTS and RTS
signals, and RS485 Driver Enable. They are able to communicate at speeds of up to
17 Mbit/s.
USART1, USART2, USART3, USART6, and USART10 also provide Smartcard mode (ISO
7816 compliant) and SPI-like communication capability.
The USARTs embed a Transmit FIFO (TXFIFO) and a Receive FIFO (RXFIFO). FIFO mode
is enabled by software and is disabled by default.
46/236
DS13314 Rev 3
STM32H733xG
Functional overview
All USART have a clock domain independent from the CPU clock, allowing the USARTx to
wake up the MCU from Stop mode.The wakeup from Stop mode is programmable and can
be done on:
•
Start bit detection
•
Any received data frame
•
A specific programmed data frame
•
Specific TXFIFO/RXFIFO status when FIFO mode is enabled.
All USART interfaces can be served by the DMA controller.
Table 5. USART features
USART modes/features(1)
USART1/2/3/6/10
UART4/5/7/8/9
Hardware flow control for modem
X
X
Continuous communication using DMA
X
X
Multiprocessor communication
X
X
Synchronous mode (Master/Slave)
X
-
Smartcard mode
X
-
Single-wire Half-duplex communication
X
X
IrDA SIR ENDEC block
X
X
LIN mode
X
X
Dual clock domain and wakeup from low power mode
X
X
Receiver timeout interrupt
X
X
Modbus communication
X
X
Auto baud rate detection
X
X
Driver Enable
X
X
USART data length
7, 8 and 9 bits
Tx/Rx FIFO
X
Tx/Rx FIFO size
X
16
1. X = supported.
3.38
Low-power universal asynchronous receiver transmitter
(LPUART)
The device embeds one Low-Power UART (LPUART1). The LPUART supports
asynchronous serial communication with minimum power consumption. It supports half
duplex single wire communication and modem operations (CTS/RTS). It allows
multiprocessor communication.
The LPUARTs embed a Transmit FIFO (TXFIFO) and a Receive FIFO (RXFIFO). FIFO
mode is enabled by software and is disabled by default.
DS13314 Rev 3
47/236
53
Functional overview
STM32H733xG
The LPUART has a clock domain independent from the CPU clock, and can wakeup the
system from Stop mode. The wakeup from Stop mode are programmable and can be done
on:
•
Start bit detection
•
Any received data frame
•
A specific programmed data frame
•
Specific TXFIFO/RXFIFO status when FIFO mode is enabled.
Only a 32.768 kHz clock (LSE) is needed to allow LPUART communication up to
9600 baud. Therefore, even in Stop mode, the LPUART can wait for an incoming frame
while having an extremely low energy consumption. Higher speed clock can be used to
reach higher baudrates.
LPUART interface can be served by the DMA controller.
3.39
Serial peripheral interface (SPI)/inter- integrated sound
interfaces (I2S)
The devices feature up to six SPIs (SPI2S1, SPI2S2, SPI2S3, SPI4, SPI5 and SPI2S6) that
allow communicating up to 150 Mbits/s in Master and Slave modes, in Half-duplex, Fullduplex and Simplex modes. The 3-bit prescaler gives 8 master mode frequencies and the
frame is configurable from 4 to 16 bits. All SPI interfaces support NSS pulse mode, TI mode,
Hardware CRC calculation and 8x 8-bit embedded Rx and Tx FIFOs with DMA capability.
Four standard I2S interfaces (multiplexed with SPI1, SPI2, SPI3 and SPI6) are available.
They can be operated in Master or Slave mode, in Simplex communication modes, and can
be configured to operate as a 16-/32-bit resolution input or output channel (except SPI2S6
which is limited to 16 bits). Audio sampling frequencies from 8 kHz up to 192 kHz are
supported. When either or both of the I2S interfaces is/are configured in Master mode, the
master clock can be output to the external DAC/CODEC at 256 times the sampling
frequency. All I2S interfaces support 16x 8-bit embedded Rx and Tx FIFOs with DMA
capability.
3.40
Serial audio interfaces (SAI)
The devices embed 2 SAIs (SAI1, and SAI4) that allow designing many stereo or mono
audio protocols such as I2S, LSB or MSB-justified, PCM/DSP, TDM or AC’97. An SPDIF
output is available when the audio block is configured as a transmitter. To bring this level of
flexibility and reconfigurability, the SAI contains two independent audio sub-blocks. Each
block has it own clock generator and I/O line controller.
Audio sampling frequencies up to 192 kHz are supported.
In addition, up to 8 microphones can be supported thanks to an embedded PDM interface.
The SAI can work in master or slave configuration. The audio sub-blocks can be either
receiver or transmitter and can work synchronously or asynchronously (with respect to the
other one). The SAI can be connected with other SAIs to work synchronously.
48/236
DS13314 Rev 3
STM32H733xG
3.41
Functional overview
SPDIFRX Receiver Interface (SPDIFRX)
The SPDIFRX peripheral is designed to receive an S/PDIF flow compliant with IEC-60958
and IEC-61937. These standards support simple stereo streams up to high sample rate,
and compressed multi-channel surround sound, such as those defined by Dolby or DTS (up
to 5.1).
The main SPDIFRX features are the following:
•
Up to 4 inputs available
•
Automatic symbol rate detection
•
Maximum symbol rate: 12.288 MHz
•
Stereo stream from 32 to 192 kHz supported
•
Supports Audio IEC-60958 and IEC-61937, consumer applications
•
Parity bit management
•
Communication using DMA for audio samples
•
Communication using DMA for control and user channel information
•
Interrupt capabilities
The SPDIFRX receiver provides all the necessary features to detect the symbol rate, and
decode the incoming data stream. The user can select the wanted SPDIF input, and when a
valid signal will be available, the SPDIFRX will re-sample the incoming signal, decode the
Manchester stream, recognize frames, sub-frames and blocks elements. It delivers to the
CPU decoded data, and associated status flags.
The SPDIFRX also offers a signal named spdif_frame_sync, which toggles at the S/PDIF
sub-frame rate that will be used to compute the exact sample rate for clock drift algorithms.
3.42
Single wire protocol master interface (SWPMI)
The Single wire protocol master interface (SWPMI) is the master interface corresponding to
the Contactless Frontend (CLF) defined in the ETSI TS 102 613 technical specification. The
main features are:
•
Full-duplex communication mode
•
automatic SWP bus state management (active, suspend, resume)
•
configurable bitrate up to 2 Mbit/s
•
automatic SOF, EOF and CRC handling
SWPMI can be served by the DMA controller.
DS13314 Rev 3
49/236
53
Functional overview
3.43
STM32H733xG
Management data input/output (MDIO) slaves
The devices embed an MDIO slave interface it includes the following features:
•
–
32 x 16-bit firmware read/write, MDIO read-only output data registers
–
32 x 16-bit firmware read-only, MDIO write-only input data registers
•
Configurable slave (port) address
•
Independently maskable interrupts/events:
•
3.44
32 MDIO Registers addresses, each of which is managed using separate input and
output data registers:
–
MDIO Register write
–
MDIO Register read
–
MDIO protocol error
Able to operate in and wake up from Stop mode
SD/SDIO/MMC card host interfaces (SDMMC)
Two SDMMC host interfaces are available. They support MultiMediaCard System
Specification Version 4.51 in three different databus modes: 1 bit (default), 4 bits and 8 bits.
Both interfaces support the SD memory card specifications version 4.1. and the SDIO card
specification version 4.0. in two different databus modes: 1 bit (default) and 4 bits.
Each SDMMC host interface supports only one SD/SDIO/MMC card at any one time and a
stack of MMC Version 4.51 or previous.
The SDMMC host interface embeds a dedicated DMA controller allowing high-speed
transfers between the interface and the SRAM.
3.45
Controller area network (FDCAN1, FDCAN2, FDCAN3)
The controller area network (CAN) subsystem consists of two CAN modules, a shared
message RAM memory and a clock calibration unit.
All CAN modules (FDCAN1, FDCAN2, and FDCAN3) are compliant with ISO 11898-1 (CAN
protocol specification version 2.0 part A, B) and CAN FD protocol specification version 1.0.
FDCAN1 supports time triggered CAN (TT-FDCAN) specified in ISO 11898-4, including
event synchronized time-triggered communication, global system time, and clock drift
compensation. The FDCAN1 contains additional registers, specific to the time triggered
feature. The CAN FD option can be used together with event-triggered and time-triggered
CAN communication.
A 10-Kbyte message RAM memory implements filters, receive FIFOs, receive buffers,
transmit event FIFOs, transmit buffers (and triggers for TT-FDCAN). This message RAM is
shared between the three modules - FDCAN1 FDCAN2 and FDCAN3.
The common clock calibration unit is optional. It can be used to generate a calibrated clock
for FDCAN1, FDCAN2 and FDCAN3 from the HSI internal RC oscillator and the PLL, by
evaluating CAN messages received by the FDCAN1.
50/236
DS13314 Rev 3
STM32H733xG
3.46
Functional overview
Universal serial bus on-the-go high-speed (OTG_HS)
The devices embed an USB OTG high-speed (up to 480 Mbit/s) device/host/OTG peripheral
that supports both full-speed and high-speed operations. It integrates the transceivers for
full-speed operation (12 Mbit/s) and a UTMI low-pin interface (ULPI) for high-speed
operation (480 Mbit/s). When using the USB OTG_HS interface in HS mode, an external
PHY device connected to the ULPI is required.
The USB OTG_HS peripheral is compliant with the USB 2.0 specification and with the OTG
2.0 specification. It features software-configurable endpoint setting and supports
suspend/resume. The USB OTG_HS controller requires a dedicated 48 MHz clock that is
generated by a PLL connected to the HSE oscillator.
The main features are:
3.47
•
Combined Rx and Tx FIFO size of 4 Kbytes with dynamic FIFO sizing
•
Supports the session request protocol (SRP) and host negotiation protocol (HNP)
•
8 bidirectional endpoints
•
16 host channels with periodic OUT support
•
Software configurable to OTG1.3 and OTG2.0 modes of operation
•
USB 2.0 LPM (Link Power Management) support
•
Battery Charging Specification Revision 1.2 support
•
Internal FS OTG PHY support
•
External HS or HS OTG operation supporting ULPI in SDR mode The OTG PHY is
connected to the microcontroller ULPI port through 12 signals. It can be clocked using
the 60 MHz output.
•
Internal USB DMA
•
HNP/SNP/IP inside (no need for any external resistor)
•
For OTG/Host modes, a power switch is needed in case bus-powered devices are
connected
Ethernet MAC interface with dedicated DMA controller (ETH)
The devices provide an IEEE-802.3-2002-compliant media access controller (MAC) for
ethernet LAN communications through an industry-standard medium-independent interface
(MII) or a reduced medium-independent interface (RMII). The microcontroller requires an
external physical interface device (PHY) to connect to the physical LAN bus (twisted-pair,
fiber, etc.). The PHY is connected to the device MII port using 17 signals for MII or 9 signals
for RMII, and can be clocked using the 25 MHz (MII) from the microcontroller.
DS13314 Rev 3
51/236
53
Functional overview
STM32H733xG
The devices include the following features:
3.48
•
Supports 10 and 100 Mbit/s rates
•
Dedicated DMA controller allowing high-speed transfers between the dedicated SRAM
and the descriptors
•
Tagged MAC frame support (VLAN support)
•
Half-duplex (CSMA/CD) and full-duplex operation
•
MAC control sublayer (control frames) support
•
32-bit CRC generation and removal
•
Several address filtering modes for physical and multicast address (multicast and
group addresses)
•
32-bit status code for each transmitted or received frame
•
Internal FIFOs to buffer transmit and receive frames. The transmit FIFO and the
receive FIFO are both 2 Kbytes.
•
Supports hardware PTP (precision time protocol) in accordance with IEEE 1588 2008
(PTP V2) with the time stamp comparator connected to the TIM2 input
•
Triggers interrupt when system time becomes greater than target time
High-definition multimedia interface (HDMI)
- consumer electronics control (CEC)
The devices embed a HDMI-CEC controller that provides hardware support for the
Consumer Electronics Control (CEC) protocol (Supplement 1 to the HDMI standard).
This protocol provides high-level control functions between all audiovisual products in an
environment. It is specified to operate at low speeds with minimum processing and memory
overhead. It has a clock domain independent from the CPU clock, allowing the HDMI-CEC
controller to wakeup the MCU from Stop mode on data reception.
3.49
Debug infrastructure
The devices offer a comprehensive set of debug and trace features to support software
development and system integration.
•
Breakpoint debugging
•
Code execution tracing
•
Software instrumentation
•
JTAG debug port
•
Serial-wire debug port
•
Trigger input and output
•
Serial-wire trace port
•
Trace port
•
Arm® CoreSight™ debug and trace components
The debug can be controlled via a JTAG/Serial-wire debug access port, using industry
standard debugging tools. The trace port performs data capture for logging and analysis.
52/236
DS13314 Rev 3
STM32H733xG
4
Memory mapping
Memory mapping
Refer to the product line reference manual for details on the memory mapping as well as the
boundary addresses for all peripherals.
DS13314 Rev 3
53/236
53
Pinouts, pin descriptions and alternate functions
5
STM32H733xG
Pinouts, pin descriptions and alternate functions
Figure 4. TFBGA100 pinout
1
2
3
4
5
6
7
8
9
10
A
PC14OSC32_IN
PC13
PE2
PB9
PB7
PB4
PB3
PA15
PA14
PA13
B
PC15OSC32_OUT
VBAT
PE3
PB8
PB6
PD5
PD2
PC11
PC10
PA12
C
PH0-OSC_IN
VSS
PE4
PE1
PB5
PD6
PD3
PC12
PA9
PA11
D
PH1OSC_OUT
VDD
PE5
PE0
BOOT0
PD7
PD4
PD0
PA8
PA10
E
NRST
PC2_C
PE6
VSS
VSS
VSS
VCAP
PD1
PC9
PC7
F
PC0
PC1
PC3_C
VDD
VDD
VDD33USB
PDR_ON
VCAP
PC8
PC6
G
VSSA
PA0
PA4
PC4
PB2
PE10
PE14
PD15
PD11
PB15
H
VDDA
PA1
PA5
PC5
PE7
PE11
PE15
PD14
PD10
PB14
J
VSS
PA2
PA6
PB0
PE8
PE12
PB10
PB13
PD9
PD13
K
VDD
PA3
PA7
PB1
PE9
PE13
PB11
PB12
PD8
PD12
MSv52520V1.
1. The above figure shows the package top view.
54/236
DS13314 Rev 3
STM32H733xG
Pinouts, pin descriptions and alternate functions
VDD
VSS
PE1
PE0
PB9
PB8
BOOT0
PB7
PB6
PB5
PB4
PB3
PD7
PD6
PD5
PD4
PD3
PD2
PD1
PD0
PC12
PC11
PC10
PA15
PA14
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
Figure 5. LQFP100 pinout
PE2
1
75
VDD
PE3
2
74
VSS
PE4
3
73
VCAP
PE5
4
72
PA13
PE6
5
71
PA12
VBAT
6
70
PA11
PC13
7
69
PA10
PC14-OSC32_IN
8
68
PA9
PC15-OSC32_OUT
9
67
PA8
VSS
10
66
PC9
VDD
11
65
PC8
PH0-OSC_IN
12
64
PC7
PH1-OSC_OUT
13
63
PC6
NRST
14
62
PD15
PC0
15
61
PD14
PC1
16
60
PD13
PC2_C
17
59
PD12
PC3_C
18
58
PD11
VSSA
19
57
PD10
VREF+
20
56
PD9
VDDA
21
55
PD8
PA0
22
54
PB15
PA1
23
53
PB14
PA2
24
52
PB13
PA3
25
51
PB12
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
VSS
VDD
PA4
PA5
PA6
PA7
PC4
PC5
PB0
PB1
PB2
PE7
PE8
PE9
PE10
PE11
PE12
PE13
PE14
PE15
PB10
PB11
VCAP
VSS
VDD
LQFP100
MSv52521V1.
1. The above figure shows the package top view.
DS13314 Rev 3
55/236
86
Pinouts, pin descriptions and alternate functions
STM32H733xG
144
143
142
141
140
139
138
137
136
135
134
133
132
131
130
129
128
127
126
125
124
123
122
121
120
119
118
117
116
115
114
113
112
111
110
109
VDD
PDR_ON
PE1
PE0
PB9
PB8
BOOT0
PB7
PB6
PB5
PB4
PB3
PG15
VDD
VSS
PG14
PG13
PG12
PG11
PG10
PG9
PD7
PD6
VDD
VSS
PD5
PD4
PD3
PD2
PD1
PD0
PC12
PC11
PC10
PA15
PA14
Figure 6. LQFP144 pinout
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
LQFP144
108
107
106
105
104
103
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
VDD
VSS
VCAP
PA13
PA12
PA11
PA10
PA9
PA8
PC9
PC8
PC7
PC6
VDD33USB
VSS
PG8
PG7
PG6
PG5
PG4
PG3
PG2
PD15
PD14
VDD
VSS
PD13
PD12
PD11
PD10
PD9
PD8
PB15
PB14
PB13
PB12
PA3
VSS
VDD
PA4
PA5
PA6
PA7
PC4
PC5
PB0
PB1
PB2
PF11
PF12
VSS
VDD
PF13
PF14
PF15
PG0
PG1
PE7
PE8
PE9
VSS
VDD
PE10
PE11
PE12
PE13
PE14
PE15
PB10
PB11
VCAP
VDD
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
PE2
PE3
PE4
PE5
PE6
VBAT
PC13
PC14-OSC32_IN
PC15-OSC32_OUT
PF0
PF1
PF2
PF3
PF4
PF5
VSS
VDD
PF6
PF7
PF8
PF9
PF10
PH0-OSC_IN
PH1-OSC_OUT
NRST
PC0
PC1
PC2_C
PC3_C
VDD
VSSA
VREF+
VDDA
PA0
PA1
PA2
MSv52522V1.
1. The above figure shows the package top view.
56/236
DS13314 Rev 3
STM32H733xG
Pinouts, pin descriptions and alternate functions
Figure 7. UFBGA144 ballout
1
2
3
4
5
6
7
8
9
10
11
12
A
PC13
PE3
PE2
PE1
PE0
PB4
PB3
PD6
PD7
PA15
PA14
PA13
B
PC14OSC32_IN
PE4
PE5
PE6
PB9
PB5
PG15
PG12
PD5
PC11
PC10
PA12
C
PC15OSC32_OUT
VBAT
PF0
PF1
PB8
PB6
PG14
PG11
PD4
PC12
VDD33USB
PA11
D
PH0-OSC_IN
VSS
VDD
PF2
BOOT0
PB7
PG13
PG10
PD3
PD1
PA10
PA9
E
PH1OSC_OUT
PF3
PF4
PF5
PDR_ON
VSS
VSS
PG9
PD2
PD0
PC9
PA8
F
NRST
PF7
PF6
VDD
VDD
VDD
VDD
VDD
VDD
VDD
PC8
PC7
G
PF10
PF9
PF8
VSS
VDD
VDD
VDD
VSS
VCAP
VSS
PG8
PC6
H
PC0
PC1
PC2
PC3
VSS
VSS
VCAP
PE11
PD11
PG7
PG6
PG5
J
VSSA
PA0
PA4
PC4
PB2
PG1
PE10
PE12
PD10
PG4
PG3
PG2
K
VREF-
PA1
PA5
PC5
PF13
PG0
PE9
PE13
PD9
PD13
PD14
PD15
L
VREF+
PA2
PA6
PB0
PF12
PF15
PE8
PE14
PD8
PD12
PB14
PB15
M
VDDA
PA3
PA7
PB1
PF11
PF14
PE7
PE15
PB10
PB11
PB12
PB13
MSv52523V1.
1. The above figure shows the package top view.
Table 6. Legend/abbreviations used in the pinout table
Name
Pin name
Pin type
Abbreviation
Unless otherwise specified in brackets below the pin name, the pin function during
and after reset is the same as the actual pin name
S
Supply pin
I
Input only pin
I/O
Input / output pin
ANA
Analog-only Input
FT
5 V tolerant I/O
TT
3.3 V tolerant I/O
B
Dedicated BOOT0 pin
RST
I/O structure
Notes
Definition
Bidirectional reset pin with embedded weak pull-up resistor
Option for TT and FT I/Os
_f
I2C FM+ option
_a
analog option (supplied by VDDA)
_u
USB option (supplied by VDD33USB)
_h
High-speed low-voltage I/O
Unless otherwise specified by a note, all I/Os are set as floating inputs during and
after reset.
DS13314 Rev 3
57/236
86
Pinouts, pin descriptions and alternate functions
STM32H733xG
Table 6. Legend/abbreviations used in the pinout table (continued)
Name
Pin functions
Abbreviation
Definition
Alternate
functions
Functions selected through GPIOx_AFR registers
Additional
functions
Functions directly selected/enabled through peripheral registers
Table 7. STM32H733 pin and ball descriptions
1
A3
PE2
I/O
FT_h
-
B3
2
2
A2
PE3
I/O
FT_h
-
TRACED0, TIM15_BKIN, SAI1_SD_B,
SAI4_SD_B, USART10_TX, FMC_A19,
EVENTOUT
-
-
TRACED1, SAI1_D2,
DFSDM1_DATIN3, TIM15_CH1N,
SPI4_NSS, SAI1_FS_A, SAI4_FS_A,
SAI4_D2, FMC_A20,
DCMI_D4/PSSI_D4, LCD_B0,
EVENTOUT
-
-
TRACED2, SAI1_CK2,
DFSDM1_CKIN3, TIM15_CH1,
SPI4_MISO, SAI1_SCK_A,
SAI4_SCK_A, SAI4_CK2, FMC_A21,
DCMI_D6/PSSI_D6, LCD_G0,
EVENTOUT
-
-
C3
D3
3
4
3
4
UFBGA144
1
LQFP144
A3
TRACECLK, SAI1_CK1,
USART10_RX, SPI4_SCK,
SAI1_MCLK_A, SAI4_MCLK_A,
OCTOSPIM_P1_IO2, SAI4_CK1,
ETH_MII_TXD3, FMC_A23,
EVENTOUT
LQFP100
Alternate functions
TFBGA100
Notes
I/O structure
Pin type
Pin number
B2
B3
Pin name (function
after reset)
PE4
PE5
I/O
I/O
FT_h
FT_h
Additional
functions
-
E3
5
5
B4
PE6
I/O
FT_h
-
TRACED3, TIM1_BKIN2, SAI1_D1,
TIM15_CH2, SPI4_MOSI, SAI1_SD_A,
SAI4_SD_A, SAI4_D1, SAI4_MCLK_B,
TIM1_BKIN2_COMP12, FMC_A22,
DCMI_D7/PSSI_D7, LCD_G1,
EVENTOUT
B2
6
6
C2
VBAT
S
-
-
-
-
A2
7
7
A1
PC13
I/O
FT
-
EVENTOUT
RTC_TAMP1/
RTC_TS,
WKUP4
A1
8
8
B1
PC14-OSC32_IN
I/O
FT
-
EVENTOUT
OSC32_IN
B1
9
9
C1
PC15-OSC32_OUT
I/O
FT
-
EVENTOUT
OSC32_OUT
58/236
DS13314 Rev 3
STM32H733xG
Pinouts, pin descriptions and alternate functions
Table 7. STM32H733 pin and ball descriptions (continued)
TFBGA100
LQFP100
LQFP144
UFBGA144
Pin name (function
after reset)
Pin type
I/O structure
Notes
Pin number
Alternate functions
-
-
10
C3
PF0
I/O
FT_fh
-
I2C2_SDA(boot), I2C5_SDA,
OCTOSPIM_P2_IO0, FMC_A0,
TIM23_CH1, EVENTOUT
-
-
-
11
C4
PF1
I/O
FT_fh
-
I2C2_SCL(boot), I2C5_SCL,
OCTOSPIM_P2_IO1, FMC_A1,
TIM23_CH2, EVENTOUT
-
-
-
12
D4
PF2
I/O
FT_h
-
I2C2_SMBA, I2C5_SMBA,
OCTOSPIM_P2_IO2, FMC_A2,
TIM23_CH3, EVENTOUT
-
-
-
13
E2
PF3
I/O
FT_ha
-
OCTOSPIM_P2_IO3, FMC_A3,
TIM23_CH4, EVENTOUT
ADC3_INP5
-
-
14
E3
PF4
I/O
FT_ha
-
OCTOSPIM_P2_CLK, FMC_A4,
EVENTOUT
ADC3_INN5,
ADC3_INP9
-
-
15
E4
PF5
I/O
FT_ha
-
OCTOSPIM_P2_NCLK, FMC_A5,
EVENTOUT
ADC3_INP4
-
10
16
-
VSS
S
-
-
-
-
-
11
17
-
VDD
S
-
-
-
-
-
-
18
F3
PF6
I/O
FT_ha
-
TIM16_CH1, FDCAN3_RX, SPI5_NSS,
SAI1_SD_B, UART7_RX, SAI4_SD_B,
OCTOSPIM_P1_IO3, TIM23_CH1,
EVENTOUT
ADC3_INN4,
ADC3_INP8
-
TIM17_CH1, FDCAN3_TX, SPI5_SCK,
SAI1_MCLK_B, UART7_TX,
SAI4_MCLK_B, OCTOSPIM_P1_IO2,
TIM23_CH2, EVENTOUT
ADC3_INP3
-
TIM16_CH1N, SPI5_MISO,
SAI1_SCK_B,
UART7_RTS/UART7_DE,
SAI4_SCK_B, TIM13_CH1,
OCTOSPIM_P1_IO0, TIM23_CH3,
EVENTOUT
ADC3_INN3,
ADC3_INP7
ADC3_INP2
-
-
-
-
19
20
F2
G3
PF7
PF8
I/O
I/O
FT_ha
FT_ha
Additional
functions
-
-
21
G2
PF9
I/O
FT_ha
-
TIM17_CH1N, SPI5_MOSI,
SAI1_FS_B, UART7_CTS, SAI4_FS_B,
TIM14_CH1, OCTOSPIM_P1_IO1,
TIM23_CH4, EVENTOUT
-
-
22
G1
PF10
I/O
FT_ha
-
TIM16_BKIN, SAI1_D3, PSSI_D15,
OCTOSPIM_P1_CLK, SAI4_D3,
DCMI_D11/PSSI_D11, LCD_DE,
EVENTOUT
ADC3_INN2,
ADC3_INP6
C1
12
23
D1
PH0-OSC_IN
I/O
FT
-
EVENTOUT
OSC_IN
DS13314 Rev 3
59/236
86
Pinouts, pin descriptions and alternate functions
STM32H733xG
Table 7. STM32H733 pin and ball descriptions (continued)
TFBGA100
LQFP100
LQFP144
UFBGA144
Pin name (function
after reset)
Pin type
I/O structure
Notes
Pin number
Alternate functions
D1
13
24
E1
PH1-OSC_OUT
I/O
FT
-
EVENTOUT
OSC_OUT
E1
14
25
F1
NRST
I/O
RST
-
-
-
-
FMC_D12/FMC_AD12,
DFSDM1_CKIN0, DFSDM1_DATIN4,
SAI4_FS_B, FMC_A25,
OTG_HS_ULPI_STP, LCD_G2,
FMC_SDNWE, LCD_R5, EVENTOUT
ADC123_INP10
-
TRACED0, SAI4_D1, SAI1_D1,
DFSDM1_DATIN0, DFSDM1_CKIN4,
SPI2_MOSI/I2S2_SDO, SAI1_SD_A,
SAI4_SD_A, SDMMC2_CK,
OCTOSPIM_P1_IO4, ETH_MDC,
MDIOS_MDC, LCD_G5, EVENTOUT
ADC123_INN10,
ADC123_INP11,
RTC_TAMP3,
WKUP6
ADC123_INN11,
ADC123_INP12
F1
F2
15
16
26
27
-
-
-
E2
17
28
(1)
(1)
(1)
H1
H2
PC0
PC1
I/O
I/O
FT_ha
FT_ha
Additional
functions
H3
PC2
I/O
FT_a
-
PWR_DEEPSLEEP, DFSDM1_CKIN1,
OCTOSPIM_P1_IO5,
SPI2_MISO/I2S2_SDI,
DFSDM1_CKOUT,
OCTOSPIM_P1_IO2,
OTG_HS_ULPI_DIR, ETH_MII_TXD2,
FMC_SDNE0, EVENTOUT
-
PC2_C
AN
A
TT_a
-
-
ADC3_INN1,
ADC3_INP0
ADC12_INN12,
ADC12_INP13
H4
PC3
I/O
FT_a
-
PWR_SLEEP, DFSDM1_DATIN1,
OCTOSPIM_P1_IO6,
SPI2_MOSI/I2S2_SDO,
OCTOSPIM_P1_IO0,
OTG_HS_ULPI_NXT,
ETH_MII_TX_CLK, FMC_SDCKE0,
EVENTOUT
(1)
-
PC3_C
AN
A
TT_a
-
-
ADC3_INP1
-
30
-
VDD
S
-
-
-
-
G1
19
31
J1
VSSA
S
-
-
-
-
-
-
-
K1
VREF-
S
-
-
-
-
-
20
32
L1
VREF+
S
-
-
-
-
H1
21
33
M1
VDDA
S
-
-
-
-
-
-
-
F3
18
29
-
(1)
60/236
(1)
DS13314 Rev 3
STM32H733xG
Pinouts, pin descriptions and alternate functions
Table 7. STM32H733 pin and ball descriptions (continued)
H2
J2
22
23
24
35
36
J2
K2
L2
PA0
PA1
PA2
I/O
I/O
I/O
I/O structure
Pin type
UFBGA144
LQFP144
34
Pin name (function
after reset)
FT_ha
FT_ha
FT_ha
Notes
G2
LQFP100
TFBGA100
Pin number
Alternate functions
Additional
functions
-
TIM2_CH1/TIM2_ETR, TIM5_CH1,
TIM8_ETR, TIM15_BKIN,
SPI6_NSS/I2S6_WS,
USART2_CTS/USART2_NSS,
UART4_TX, SDMMC2_CMD,
SAI4_SD_B, ETH_MII_CRS,
FMC_A19, EVENTOUT
ADC1_INP16,
WKUP1
-
TIM2_CH2, TIM5_CH2, LPTIM3_OUT,
TIM15_CH1N,
USART2_RTS/USART2_DE,
UART4_RX, OCTOSPIM_P1_IO3,
SAI4_MCLK_B,
ETH_MII_RX_CLK/ETH_RMII_REF_C
LK, OCTOSPIM_P1_DQS, LCD_R2,
EVENTOUT
ADC1_INN16,
ADC1_INP17
-
TIM2_CH3, TIM5_CH3, LPTIM4_OUT,
TIM15_CH1, OCTOSPIM_P1_IO0,
USART2_TX(boot), SAI4_SCK_B,
ETH_MDIO, MDIOS_MDIO, LCD_R1,
EVENTOUT
ADC12_INP14,
WKUP2
ADC12_INP15
K2
25
37
M2
PA3
I/O
FT_ha
-
TIM2_CH4, TIM5_CH4, LPTIM5_OUT,
TIM15_CH2, I2S6_MCK,
OCTOSPIM_P1_IO2,
USART2_RX(boot), LCD_B2,
OTG_HS_ULPI_D0, ETH_MII_COL,
OCTOSPIM_P1_CLK, LCD_B5,
EVENTOUT
-
26
38
-
VSS
S
-
-
-
-
-
27
39
-
VDD
S
-
-
-
-
-
D1PWREN, TIM5_ETR,
SPI1_NSS(boot)/I2S1_WS,
SPI3_NSS/I2S3_WS, USART2_CK,
SPI6_NSS/I2S6_WS,
FMC_D8/FMC_AD8,
DCMI_HSYNC/PSSI_DE,
LCD_VSYNC, EVENTOUT
ADC12_INP18,
DAC1_OUT1
-
D2PWREN, TIM2_CH1/TIM2_ETR,
TIM8_CH1N,
SPI1_SCK(boot)/I2S1_CK,
SPI6_SCK/I2S6_CK,
OTG_HS_ULPI_CK,
FMC_D9/FMC_AD9, PSSI_D14,
LCD_R4, EVENTOUT
ADC12_INN18,
ADC12_INP19,
DAC1_OUT2
G3
H3
28
29
40
41
J3
K3
PA4
PA5
I/O
I/O
TT_ha
TT_ha
DS13314 Rev 3
61/236
86
Pinouts, pin descriptions and alternate functions
STM32H733xG
Table 7. STM32H733 pin and ball descriptions (continued)
K3
G4
H4
J4
K4
G5
62/236
30
31
32
33
34
35
36
43
44
45
46
47
48
L3
M3
J4
K4
L4
M4
J5
PA6
PA7
PC4
PC5
PB0
PB1
PB2
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O structure
Pin type
UFBGA144
LQFP144
42
Pin name (function
after reset)
FT_ha
TT_ha
TT_ha
TT_ha
TT_ha
FT_ha
FT_ha
Notes
J3
LQFP100
TFBGA100
Pin number
Alternate functions
Additional
functions
-
TIM1_BKIN, TIM3_CH1, TIM8_BKIN,
SPI1_MISO(boot)/I2S1_SDI,
OCTOSPIM_P1_IO3,
SPI6_MISO/I2S6_SDI, TIM13_CH1,
TIM8_BKIN_COMP12, MDIOS_MDC,
TIM1_BKIN_COMP12,
DCMI_PIXCLK/PSSI_PDCK, LCD_G2,
EVENTOUT
ADC12_INP3
-
TIM1_CH1N, TIM3_CH2, TIM8_CH1N,
SPI1_MOSI(boot)/I2S1_SDO,
SPI6_MOSI/I2S6_SDO, TIM14_CH1,
OCTOSPIM_P1_IO2,
ETH_MII_RX_DV/ETH_RMII_CRS_DV,
FMC_SDNWE, LCD_VSYNC,
EVENTOUT
ADC12_INN3,
ADC12_INP7,
OPAMP1_VINM
-
PWR_DEEPSLEEP, FMC_A22,
DFSDM1_CKIN2, I2S1_MCK,
SPDIFRX1_IN3, SDMMC2_CKIN,
ETH_MII_RXD0/ETH_RMII_RXD0,
FMC_SDNE0, LCD_R7, EVENTOUT
ADC12_INP4,
OPAMP1_VOUT,
COMP1_INM
-
PWR_SLEEP, SAI4_D3, SAI1_D3,
DFSDM1_DATIN2, PSSI_D15,
SPDIFRX1_IN4, OCTOSPIM_P1_DQS,
ETH_MII_RXD1/ETH_RMII_RXD1,
FMC_SDCKE0, COMP1_OUT,
LCD_DE, EVENTOUT
ADC12_INN4,
ADC12_INP8,
OPAMP1_VINM
-
TIM1_CH2N, TIM3_CH3, TIM8_CH2N,
OCTOSPIM_P1_IO1,
DFSDM1_CKOUT, UART4_CTS,
LCD_R3, OTG_HS_ULPI_D1,
ETH_MII_RXD2, LCD_G1, EVENTOUT
ADC12_INN5,
ADC12_INP9,
OPAMP1_VINP,
COMP1_INP
-
TIM1_CH3N, TIM3_CH4, TIM8_CH3N,
OCTOSPIM_P1_IO0,
DFSDM1_DATIN1, LCD_R6,
OTG_HS_ULPI_D2, ETH_MII_RXD3,
LCD_G0, EVENTOUT
ADC12_INP5,
COMP1_INM
-
RTC_OUT, SAI4_D1, SAI1_D1,
DFSDM1_CKIN1, SAI1_SD_A,
SPI3_MOSI/I2S3_SDO, SAI4_SD_A,
OCTOSPIM_P1_CLK,
OCTOSPIM_P1_DQS, ETH_TX_ER,
TIM23_ETR, EVENTOUT
COMP1_INP
DS13314 Rev 3
STM32H733xG
Pinouts, pin descriptions and alternate functions
Table 7. STM32H733 pin and ball descriptions (continued)
49
M5
PF11
I/O
FT_ha
-
-
-
50
L5
PF12
I/O
FT_ha
-
OCTOSPIM_P2_DQS, FMC_A6,
TIM24_CH2, EVENTOUT
ADC1_INN2,
ADC1_INP6
-
-
51
-
VSS
S
-
-
-
-
-
-
52
-
VDD
S
-
-
-
-
-
-
53
K5
PF13
I/O
FT_ha
-
DFSDM1_DATIN6, I2C4_SMBA,
FMC_A7, TIM24_CH3, EVENTOUT
ADC2_INP2
-
-
54
M6
PF14
I/O FT_fha
-
DFSDM1_CKIN6, I2C4_SCL, FMC_A8,
TIM24_CH4, EVENTOUT
ADC2_INN2,
ADC2_INP6
-
-
55
L6
PF15
I/O
FT_fh
-
I2C4_SDA, FMC_A9, EVENTOUT
-
-
-
56
K6
PG0
I/O
FT_h
-
OCTOSPIM_P2_IO4, UART9_RX,
FMC_A10, EVENTOUT
-
-
-
57
J6
PG1
I/O
TT_h
-
OCTOSPIM_P2_IO5, UART9_TX,
FMC_A11, EVENTOUT
OPAMP2_VINM
H5
37
58
M7
PE7
I/O
TT_ha
-
TIM1_ETR, DFSDM1_DATIN2,
UART7_RX, OCTOSPIM_P1_IO4,
FMC_D4/FMC_AD4, EVENTOUT
OPAMP2_VOUT,
COMP2_INM
OPAMP2_VINM
UFBGA144
-
LQFP144
-
SPI5_MOSI, OCTOSPIM_P1_NCLK,
SAI4_SD_B, FMC_NRAS,
DCMI_D12/PSSI_D12, TIM24_CH1,
EVENTOUT
LQFP100
Alternate functions
TFBGA100
Notes
I/O structure
Pin type
Pin number
Pin name (function
after reset)
Additional
functions
ADC1_INP2
J5
38
59
L7
PE8
I/O
TT_ha
-
TIM1_CH1N, DFSDM1_CKIN2,
UART7_TX, OCTOSPIM_P1_IO5,
FMC_D5/FMC_AD5, COMP2_OUT,
EVENTOUT
K5
39
60
K7
PE9
I/O
TT_ha
-
TIM1_CH1, DFSDM1_CKOUT,
UART7_RTS/UART7_DE,
OCTOSPIM_P1_IO6,
FMC_D6/FMC_AD6, EVENTOUT
OPAMP2_VINP,
COMP2_INP
-
-
61
-
VSS
S
-
-
-
-
-
-
62
-
VDD
S
-
-
-
-
G6
40
63
J7
PE10
I/O
FT_ha
-
TIM1_CH2N, DFSDM1_DATIN4,
UART7_CTS, OCTOSPIM_P1_IO7,
FMC_D7/FMC_AD7, EVENTOUT
COMP2_INM
-
TIM1_CH2, DFSDM1_CKIN4,
SPI4_NSS(boot), SAI4_SD_B,
OCTOSPIM_P1_NCS,
FMC_D8/FMC_AD8, LCD_G3,
EVENTOUT
COMP2_INP
H6
41
64
H8
PE11
I/O
FT_ha
DS13314 Rev 3
63/236
86
Pinouts, pin descriptions and alternate functions
STM32H733xG
Table 7. STM32H733 pin and ball descriptions (continued)
65
J8
PE12
I/O
FT_h
-
K6
43
66
K8
PE13
I/O
FT_h
-
TIM1_CH3, DFSDM1_CKIN5,
SPI4_MISO(boot), SAI4_FS_B,
FMC_D10/FMC_AD10, COMP2_OUT,
LCD_DE, EVENTOUT
-
G7
44
67
L8
PE14
I/O
FT_h
-
TIM1_CH4, SPI4_MOSI(boot),
SAI4_MCLK_B, FMC_D11/FMC_AD11,
LCD_CLK, EVENTOUT
-
-
TIM1_BKIN, USART10_CK,
FMC_D12/FMC_AD12,
TIM1_BKIN_COMP12, LCD_R7,
EVENTOUT
-
-
TIM2_CH3, LPTIM2_IN1, I2C2_SCL,
SPI2_SCK/I2S2_CK,
DFSDM1_DATIN7, USART3_TX(boot),
OCTOSPIM_P1_NCS,
OTG_HS_ULPI_D3, ETH_MII_RX_ER,
LCD_G4, EVENTOUT
-
-
H7
J7
45
46
68
69
UFBGA144
42
LQFP144
J6
TIM1_CH3N, DFSDM1_DATIN5,
SPI4_SCK(boot), SAI4_SCK_B,
FMC_D9/FMC_AD9, COMP1_OUT,
LCD_B4, EVENTOUT
LQFP100
Alternate functions
TFBGA100
Notes
I/O structure
Pin type
Pin number
M8
M9
Pin name (function
after reset)
PE15
PB10
I/O
I/O
FT_h
FT_fh
Additional
functions
-
K7
47
70
M10
PB11
I/O
FT_f
-
TIM2_CH4, LPTIM2_ETR, I2C2_SDA,
DFSDM1_CKIN7, USART3_RX(boot),
OTG_HS_ULPI_D4,
ETH_MII_TX_EN/ETH_RMII_TX_EN,
LCD_G5, EVENTOUT
F8
48
71
H7
VCAP
S
-
-
-
-
-
49
-
-
VSS
S
-
-
-
-
-
50
72
-
VDD
S
-
-
-
-
-
TIM1_BKIN, OCTOSPIM_P1_NCLK,
I2C2_SMBA, SPI2_NSS/I2S2_WS,
DFSDM1_DATIN1, USART3_CK,
FDCAN2_RX, OTG_HS_ULPI_D5,
ETH_MII_TXD0/ETH_RMII_TXD0,
OCTOSPIM_P1_IO0,
TIM1_BKIN_COMP12, UART5_RX,
EVENTOUT
-
K8
64/236
51
73
M11
PB12
I/O
FT_h
DS13314 Rev 3
STM32H733xG
Pinouts, pin descriptions and alternate functions
Table 7. STM32H733 pin and ball descriptions (continued)
H10
52
53
75
M12
L11
PB13
PB14
I/O
I/O
I/O structure
Pin type
UFBGA144
LQFP144
74
Pin name (function
after reset)
FT_h
FT_h
Notes
J8
LQFP100
TFBGA100
Pin number
Alternate functions
Additional
functions
-
TIM1_CH1N, LPTIM2_OUT,
OCTOSPIM_P1_IO2,
SPI2_SCK/I2S2_CK, DFSDM1_CKIN1,
USART3_CTS/USART3_NSS,
FDCAN2_TX, OTG_HS_ULPI_D6,
ETH_MII_TXD1/ETH_RMII_TXD1,
SDMMC1_D0, DCMI_D2/PSSI_D2,
UART5_TX, EVENTOUT
-
-
TIM1_CH2N, TIM12_CH1,
TIM8_CH2N, USART1_TX,
SPI2_MISO/I2S2_SDI,
DFSDM1_DATIN2,
USART3_RTS/USART3_DE,
UART4_RTS/UART4_DE,
SDMMC2_D0, FMC_D10/FMC_AD10,
LCD_CLK, EVENTOUT
-
-
G10
54
76
L12
PB15
I/O
FT_h
-
RTC_REFIN, TIM1_CH3N,
TIM12_CH2, TIM8_CH3N,
USART1_RX, SPI2_MOSI/I2S2_SDO,
DFSDM1_CKIN2, UART4_CTS,
SDMMC2_D1, FMC_D11/FMC_AD11,
LCD_G7, EVENTOUT
K9
55
77
L9
PD8
I/O
FT_h
-
DFSDM1_CKIN3, USART3_TX(boot),
SPDIFRX1_IN2,
FMC_D13/FMC_AD13, EVENTOUT
-
J9
56
78
K9
PD9
I/O
FT_h
-
DFSDM1_DATIN3, USART3_RX(boot),
FMC_D14/FMC_AD14, EVENTOUT
-
H9
57
79
J9
PD10
I/O
FT_h
-
DFSDM1_CKOUT, USART3_CK,
FMC_D15/FMC_AD15, LCD_B3,
EVENTOUT
-
-
LPTIM2_IN2, I2C4_SMBA,
USART3_CTS/USART3_NSS,
OCTOSPIM_P1_IO0, SAI4_SD_A,
FMC_A16/FMC_CLE, EVENTOUT
-
-
LPTIM1_IN1, TIM4_CH1, LPTIM2_IN1,
I2C4_SCL, FDCAN3_RX,
USART3_RTS/USART3_DE,
OCTOSPIM_P1_IO1, SAI4_FS_A,
FMC_A17/FMC_ALE,
DCMI_D12/PSSI_D12, EVENTOUT
-
G9
K10
58
59
80
81
H9
L10
PD11
PD12
I/O
I/O
FT_h
FT_fh
DS13314 Rev 3
65/236
86
Pinouts, pin descriptions and alternate functions
STM32H733xG
Table 7. STM32H733 pin and ball descriptions (continued)
82
K10
PD13
I/O
FT_fh
-
-
-
83
-
VSS
S
-
-
-
-
-
-
84
-
VDD
S
-
-
-
-
H8
61
85
K11
PD14
I/O
FT_h
-
TIM4_CH3, UART8_CTS, UART9_RX,
FMC_D0/FMC_AD0, EVENTOUT
-
G8
62
86
K12
PD15
I/O
FT_h
-
TIM4_CH4, UART8_RTS/UART8_DE,
UART9_TX, FMC_D1/FMC_AD1,
EVENTOUT
-
-
-
87
J12
PG2
I/O
FT_h
-
TIM8_BKIN, TIM8_BKIN_COMP12,
FMC_A12, TIM24_ETR, EVENTOUT
-
-
-
88
J11
PG3
I/O
FT_h
-
TIM8_BKIN2, TIM8_BKIN2_COMP12,
FMC_A13, TIM23_ETR, EVENTOUT
-
-
-
89
J10
PG4
I/O
FT_h
-
TIM1_BKIN2, TIM1_BKIN2_COMP12,
FMC_A14/FMC_BA0, EVENTOUT
-
-
-
90
H12
PG5
I/O
FT_h
-
TIM1_ETR, FMC_A15/FMC_BA1,
EVENTOUT
-
-
-
91
H11
PG6
I/O
FT_h
-
TIM17_BKIN, OCTOSPIM_P1_NCS,
FMC_NE3, DCMI_D12/PSSI_D12,
LCD_R7, EVENTOUT
-
-
-
92
H10
PG7
I/O
FT_h
-
SAI1_MCLK_A, USART6_CK,
OCTOSPIM_P2_DQS, FMC_INT,
DCMI_D13/PSSI_D13, LCD_CLK,
EVENTOUT
-
-
UFBGA144
60
LQFP144
J10
LPTIM1_OUT, TIM4_CH2, I2C4_SDA,
FDCAN3_TX, OCTOSPIM_P1_IO3,
SAI4_SCK_A,
UART9_RTS/UART9_DE, FMC_A18,
DCMI_D13/PSSI_D13, EVENTOUT
LQFP100
Alternate functions
TFBGA100
Notes
I/O structure
Pin type
Pin number
Pin name (function
after reset)
Additional
functions
-
-
-
93
G11
PG8
I/O
FT_h
-
TIM8_ETR, SPI6_NSS/I2S6_WS,
USART6_RTS/USART6_DE,
SPDIFRX1_IN3, ETH_PPS_OUT,
FMC_SDCLK, LCD_G7, EVENTOUT
-
-
94
-
VSS
S
-
-
-
-
F6
-
95
C11
VDD33USB
S
-
-
-
-
-
TIM3_CH1, TIM8_CH1,
DFSDM1_CKIN3, I2S2_MCK,
USART6_TX, SDMMC1_D0DIR,
FMC_NWAIT, SDMMC2_D6,
SDMMC1_D6, DCMI_D0/PSSI_D0,
LCD_HSYNC, EVENTOUT
SWPMI_IO
F10
66/236
63
96
G12
PC6
I/O
FT_h
DS13314 Rev 3
STM32H733xG
Pinouts, pin descriptions and alternate functions
Table 7. STM32H733 pin and ball descriptions (continued)
F9
E9
D9
C9
D10
C10
B10
64
65
66
67
68
69
70
71
98
99
100
101
102
103
104
F12
F11
E11
E12
D12
D11
C12
B12
PC7
PC8
PC9
PA8
PA9
PA10
PA11
PA12
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O structure
Pin type
UFBGA144
LQFP144
97
Pin name (function
after reset)
FT_h
FT_h
FT_fh
FT_fh
FT_u
FT_u
FT_u
FT_u
Notes
E10
LQFP100
TFBGA100
Pin number
Alternate functions
Additional
functions
-
DBTRGIO, TIM3_CH2, TIM8_CH2,
DFSDM1_DATIN3, I2S3_MCK,
USART6_RX, SDMMC1_D123DIR,
FMC_NE1, SDMMC2_D7, SWPMI_TX,
SDMMC1_D7, DCMI_D1/PSSI_D1,
LCD_G6, EVENTOUT
-
-
TRACED1, TIM3_CH3, TIM8_CH3,
USART6_CK,
UART5_RTS/UART5_DE,
FMC_NE2/FMC_NCE, FMC_INT,
SWPMI_RX, SDMMC1_D0,
DCMI_D2/PSSI_D2, EVENTOUT
-
-
MCO2, TIM3_CH4, TIM8_CH4,
I2C3_SDA(boot), I2S_CKIN,
I2C5_SDA, UART5_CTS,
OCTOSPIM_P1_IO0, LCD_G3,
SWPMI_SUSPEND, SDMMC1_D1,
DCMI_D3/PSSI_D3, LCD_B2,
EVENTOUT
-
-
MCO1, TIM1_CH1, TIM8_BKIN2,
I2C3_SCL(boot), I2C5_SCL,
USART1_CK, OTG_HS_SOF,
UART7_RX, TIM8_BKIN2_COMP12,
LCD_B3, LCD_R6, EVENTOUT
-
-
TIM1_CH2, LPUART1_TX,
I2C3_SMBA, SPI2_SCK/I2S2_CK,
I2C5_SMBA, USART1_TX(boot),
ETH_TX_ER, DCMI_D0/PSSI_D0,
LCD_R5, EVENTOUT
OTG_HS_VBUS
-
TIM1_CH3, LPUART1_RX,
USART1_RX(boot), OTG_HS_ID,
MDIOS_MDIO, LCD_B4,
DCMI_D1/PSSI_D1, LCD_B1,
EVENTOUT
-
-
TIM1_CH4, LPUART1_CTS,
SPI2_NSS/I2S2_WS, UART4_RX,
USART1_CTS/USART1_NSS,
FDCAN1_RX, LCD_R4, EVENTOUT
OTG_HS_DM
(boot)
-
TIM1_ETR,
LPUART1_RTS/LPUART1_DE,
SPI2_SCK/I2S2_CK, UART4_TX,
USART1_RTS/USART1_DE,
SAI4_FS_B, FDCAN1_TX,
TIM1_BKIN2, LCD_R5, EVENTOUT
OTG_HS_DP
(boot)
DS13314 Rev 3
67/236
86
Pinouts, pin descriptions and alternate functions
STM32H733xG
Table 7. STM32H733 pin and ball descriptions (continued)
TFBGA100
LQFP100
LQFP144
UFBGA144
Pin name (function
after reset)
Pin type
I/O structure
Notes
Pin number
Alternate functions
A10
72
105
A12
PA13(JTMS/SWDIO)
I/O
FT
-
JTMS/SWDIO, EVENTOUT
-
E7
73
106
G9
VCAP
S
-
-
-
-
-
74
107
-
VSS
S
-
-
-
-
-
75
108
-
VDD
S
-
-
-
-
A9
76
109
A11
PA14(JTCK/SWCLK)
I/O
FT
-
JTCK/SWCLK, EVENTOUT
-
-
JTDI, TIM2_CH1/TIM2_ETR, CEC,
SPI1_NSS/I2S1_WS,
SPI3_NSS(boot)/I2S3_WS,
SPI6_NSS/I2S6_WS,
UART4_RTS/UART4_DE, LCD_R3,
UART7_TX, LCD_B6, EVENTOUT
-
-
DFSDM1_CKIN5, I2C5_SDA,
SPI3_SCK(boot)/I2S3_CK,
USART3_TX, UART4_TX,
OCTOSPIM_P1_IO1, LCD_B1,
SWPMI_RX, SDMMC1_D2,
DCMI_D8/PSSI_D8, LCD_R2,
EVENTOUT
-
-
DFSDM1_DATIN5, I2C5_SCL,
SPI3_MISO(boot)/I2S3_SDI,
USART3_RX, UART4_RX,
OCTOSPIM_P1_NCS, SDMMC1_D3,
DCMI_D4/PSSI_D4, LCD_B4,
EVENTOUT
-
-
TRACED3, FMC_D6/FMC_AD6,
TIM15_CH1, I2C5_SMBA,
SPI6_SCK/I2S6_CK,
SPI3_MOSI(boot)/I2S3_SDO,
USART3_CK, UART5_TX,
SDMMC1_CK, DCMI_D9/PSSI_D9,
LCD_R6, EVENTOUT
-
-
-
A8
B9
B8
C8
77
78
79
80
110
111
112
113
A10
B11
B10
C10
PA15(JTDI)
PC10
PC11
PC12
I/O
I/O
I/O
I/O
FT
FT_fh
FT_fh
FT_h
D8
81
114
E10
PD0
I/O
FT_h
-
DFSDM1_CKIN6, UART4_RX,
FDCAN1_RX(boot), UART9_CTS,
FMC_D2/FMC_AD2, LCD_B1,
EVENTOUT
E8
82
115
D10
PD1
I/O
FT_h
-
DFSDM1_DATIN6, UART4_TX,
FDCAN1_TX(boot),
FMC_D3/FMC_AD3, EVENTOUT
68/236
DS13314 Rev 3
Additional
functions
STM32H733xG
Pinouts, pin descriptions and alternate functions
Table 7. STM32H733 pin and ball descriptions (continued)
83
E9
PD2
I/O
I/O structure
Pin type
UFBGA144
LQFP144
116
Pin name (function
after reset)
FT_h
Notes
B7
LQFP100
TFBGA100
Pin number
Alternate functions
Additional
functions
-
TRACED2, FMC_D7/FMC_AD7,
TIM3_ETR, TIM15_BKIN, UART5_RX,
LCD_B7, SDMMC1_CMD,
DCMI_D11/PSSI_D11, LCD_B2,
EVENTOUT
-
-
C7
84
117
D9
PD3
I/O
FT_h
-
DFSDM1_CKOUT,
SPI2_SCK/I2S2_CK,
USART2_CTS/USART2_NSS,
FMC_CLK, DCMI_D5/PSSI_D5,
LCD_G7, EVENTOUT
D7
85
118
C9
PD4
I/O
FT_h
-
USART2_RTS/USART2_DE,
OCTOSPIM_P1_IO4, FMC_NOE,
EVENTOUT
-
B6
86
119
B9
PD5
I/O
FT_h
-
USART2_TX, OCTOSPIM_P1_IO5,
FMC_NWE, EVENTOUT
-
-
-
120
-
VSS
S
-
-
-
-
-
-
121
-
VDD
S
-
-
-
-
-
SAI4_D1, SAI1_D1, DFSDM1_CKIN4,
DFSDM1_DATIN1,
SPI3_MOSI/I2S3_SDO, SAI1_SD_A,
USART2_RX, SAI4_SD_A,
OCTOSPIM_P1_IO6, SDMMC2_CK,
FMC_NWAIT, DCMI_D10/PSSI_D10,
LCD_B2, EVENTOUT
-
-
DFSDM1_DATIN4,
SPI1_MOSI/I2S1_SDO,
DFSDM1_CKIN1, USART2_CK,
SPDIFRX1_IN1, OCTOSPIM_P1_IO7,
SDMMC2_CMD, FMC_NE1,
EVENTOUT
-
-
FDCAN3_TX, SPI1_MISO/I2S1_SDI,
USART6_RX, SPDIFRX1_IN4,
OCTOSPIM_P1_IO6, SAI4_FS_B,
SDMMC2_D0, FMC_NE2/FMC_NCE,
DCMI_VSYNC/PSSI_RDY, EVENTOUT
-
-
FDCAN3_RX, OCTOSPIM_P2_IO6,
SPI1_NSS/I2S1_WS, LCD_G3,
SAI4_SD_B, SDMMC2_D1, FMC_NE3,
DCMI_D2/PSSI_D2, LCD_B2,
EVENTOUT
-
C6
D6
-
-
87
88
-
-
122
123
124
125
A8
A9
E8
D8
PD6
PD7
PG9
PG10
I/O
I/O
I/O
I/O
FT_h
FT_h
FT_h
FT_h
DS13314 Rev 3
69/236
86
Pinouts, pin descriptions and alternate functions
STM32H733xG
Table 7. STM32H733 pin and ball descriptions (continued)
-
-
-
-
-
127
128
C8
B8
D7
PG11
PG12
PG13
I/O
I/O
I/O
I/O structure
Pin type
UFBGA144
LQFP144
126
Pin name (function
after reset)
FT_h
FT_h
FT_h
Notes
-
LQFP100
TFBGA100
Pin number
Alternate functions
Additional
functions
-
LPTIM1_IN2, USART10_RX,
SPI1_SCK/I2S1_CK, SPDIFRX1_IN1,
OCTOSPIM_P2_IO7, SDMMC2_D2,
ETH_MII_TX_EN/ETH_RMII_TX_EN,
DCMI_D3/PSSI_D3, LCD_B3,
EVENTOUT
-
-
LPTIM1_IN1, OCTOSPIM_P2_NCS,
USART10_TX, SPI6_MISO/I2S6_SDI,
USART6_RTS/USART6_DE,
SPDIFRX1_IN2, LCD_B4,
SDMMC2_D3,
ETH_MII_TXD1/ETH_RMII_TXD1,
FMC_NE4, TIM23_CH1, LCD_B1,
EVENTOUT
-
-
TRACED0, LPTIM1_OUT,
USART10_CTS/USART10_NSS,
SPI6_SCK/I2S6_CK,
USART6_CTS/USART6_NSS,
SDMMC2_D6,
ETH_MII_TXD0/ETH_RMII_TXD0,
FMC_A24, TIM23_CH2, LCD_R0,
EVENTOUT
-
-
-
-
129
C7
PG14
I/O
FT_h
-
TRACED1, LPTIM1_ETR,
USART10_RTS/USART10_DE,
SPI6_MOSI/I2S6_SDO, USART6_TX,
OCTOSPIM_P1_IO7, SDMMC2_D7,
ETH_MII_TXD1/ETH_RMII_TXD1,
FMC_A25, TIM23_CH3, LCD_B0,
EVENTOUT
-
-
130
-
VSS
S
-
-
-
-
-
-
131
-
VDD
S
-
-
-
-
-
-
132
B7
PG15
I/O
FT_h
-
USART6_CTS/USART6_NSS,
OCTOSPIM_P2_DQS, USART10_CK,
FMC_NCAS, DCMI_D13/PSSI_D13,
EVENTOUT
-
-
JTDO/TRACESWO, TIM2_CH2,
SPI1_SCK/I2S1_CK,
SPI3_SCK/I2S3_CK,
SPI6_SCK/I2S6_CK, SDMMC2_D2,
CRS_SYNC, UART7_RX, TIM24_ETR,
EVENTOUT
-
A7
70/236
89
133
A7
PB3
(JTDO/TRACESWO)
I/O
FT_h
DS13314 Rev 3
STM32H733xG
Pinouts, pin descriptions and alternate functions
Table 7. STM32H733 pin and ball descriptions (continued)
C5
B5
90
91
92
135
136
A6
B6
C6
PB4(NJTRST)
PB5
PB6
I/O
I/O
I/O
I/O structure
Pin type
UFBGA144
LQFP144
134
Pin name (function
after reset)
FT_h
FT_h
FT_fh
Notes
A6
LQFP100
TFBGA100
Pin number
Alternate functions
Additional
functions
-
NJTRST, TIM16_BKIN, TIM3_CH1,
SPI1_MISO/I2S1_SDI,
SPI3_MISO/I2S3_SDI,
SPI2_NSS/I2S2_WS,
SPI6_MISO/I2S6_SDI, SDMMC2_D3,
UART7_TX, EVENTOUT
-
-
TIM17_BKIN, TIM3_CH2, LCD_B5,
I2C1_SMBA, SPI1_MOSI/I2S1_SDO,
I2C4_SMBA, SPI3_MOSI/I2S3_SDO,
SPI6_MOSI/I2S6_SDO, FDCAN2_RX,
OTG_HS_ULPI_D7, ETH_PPS_OUT,
FMC_SDCKE1, DCMI_D10/PSSI_D10,
UART5_RX, EVENTOUT
-
-
TIM16_CH1N, TIM4_CH1,
I2C1_SCL(boot), CEC, I2C4_SCL,
USART1_TX, LPUART1_TX,
FDCAN2_TX, OCTOSPIM_P1_NCS,
DFSDM1_DATIN5, FMC_SDNE1,
DCMI_D5/PSSI_D5, UART5_TX,
EVENTOUT
-
PVD_IN
A5
93
137
D6
PB7
I/O
FT_fa
-
TIM17_CH1N, TIM4_CH2, I2C1_SDA,
I2C4_SDA, USART1_RX,
LPUART1_RX, DFSDM1_CKIN5,
FMC_NL, DCMI_VSYNC/PSSI_RDY,
EVENTOUT
D5
94
138
D5
BOOT0
I
B
-
-
VPP
-
TIM16_CH1, TIM4_CH3,
DFSDM1_CKIN7, I2C1_SCL,
I2C4_SCL, SDMMC1_CKIN,
UART4_RX, FDCAN1_RX,
SDMMC2_D4, ETH_MII_TXD3,
SDMMC1_D4, DCMI_D6/PSSI_D6,
LCD_B6, EVENTOUT
-
-
TIM17_CH1, TIM4_CH4,
DFSDM1_DATIN7, I2C1_SDA(boot),
SPI2_NSS/I2S2_WS, I2C4_SDA,
SDMMC1_CDIR, UART4_TX,
FDCAN1_TX, SDMMC2_D5,
I2C4_SMBA, SDMMC1_D5,
DCMI_D7/PSSI_D7, LCD_B7,
EVENTOUT
-
B4
A4
95
96
139
140
C5
B5
PB8
PB9
I/O
I/O
FT_fh
FT_fh
DS13314 Rev 3
71/236
86
Pinouts, pin descriptions and alternate functions
STM32H733xG
Table 7. STM32H733 pin and ball descriptions (continued)
97
141
A5
PE0
I/O
FT_h
-
C4
98
142
A4
PE1
I/O
FT_h
-
LPTIM1_IN2, UART8_TX, FMC_NBL1,
DCMI_D3/PSSI_D3, LCD_R6,
EVENTOUT
-
-
99
-
-
VSS
S
-
-
-
-
F7
-
143
E5
PDR_ON
S
-
-
-
-
-
100
144
-
VDD
S
-
-
-
-
C2
-
-
D2
VSS
S
-
-
-
-
E6
-
-
E6
VSS
S
-
-
-
-
J1
-
-
E7
VSS
S
-
-
-
-
E4
-
-
G4
VSS
S
-
-
-
-
E5
-
-
G8
VSS
S
-
-
-
-
-
-
-
G10
VSS
S
-
-
-
-
-
-
-
H5
VSS
S
-
-
-
-
-
-
-
H6
VSS
S
-
-
-
-
D2
-
-
D3
VDD
S
-
-
-
-
F5
-
-
F4
VDD
S
-
-
-
-
K1
-
-
F5
VDD
S
-
-
-
-
F4
-
-
F6
VDD
S
-
-
-
-
-
-
-
F7
VDD
S
-
-
-
-
-
-
-
F8
VDD
S
-
-
-
-
-
-
-
F9
VDD
S
-
-
-
-
-
-
-
F10
VDD
S
-
-
-
-
-
-
-
G5
VDD
S
-
-
-
-
-
-
-
G6
VDD
S
-
-
-
-
-
-
-
G7
VDD
S
-
-
-
-
LQFP100
UFBGA144
D4
LPTIM1_ETR, TIM4_ETR,
LPTIM2_ETR, UART8_RX,
SAI4_MCLK_A, FMC_NBL0,
DCMI_D2/PSSI_D2, LCD_R0,
EVENTOUT
LQFP144
Alternate functions
TFBGA100
Notes
I/O structure
Pin type
Pin number
Pin name (function
after reset)
Additional
functions
-
1. There is a direct path between Pxy_C and Pxy pins/balls, through an analog switch. Pxy alternate functions are available
on Pxy_C when the analog switch is closed. The analog switch is configured through a SYSCFG register. Refer to the
product reference manual for a detailed description of the switch configuration bits
72/236
DS13314 Rev 3
AF0
Port
SYS
AF2
AF3
AF4
AF5
AF6
AF7
AF8
AF9
AF10
AF11
CEC/
DCMI/
CRS/
DFSDM1/
FDCAN1/2
DFSDM1
PSSI/
DFSDM1/I SDMMC1
FMC/
ETH/I2C4/
CEC/
LPUART1/
/FMC/
/LCD/
DFSDM1
2C4/5/
/SPI2/I2S
LCD/
LCD/MDIO
FMC/
FDCAN3/
FDCAN3/
SAI4/
LCD/
LPTIM2/ /I2C1/2/3/
OCTO
2/SPI3/
OCTO
S/OCTOSP
LPTIM1/
PDM_
SPI1/I2S
SDMMC1/
OCTO
3/4/5/
4/5/
SPIM_P1/
I2S3/
SPIM_P1/
IM_P1/
SAI4/TIM1
SAI1/
1/SPI2/
SPDIFRX1 SPIM_P1/
LPUART LPTIM2/
SAI1/
SPI6/
OTG1_FS/ SDMMC2/
6/17/TIM1 TIM3/4/5/1
I2S2/SPI
/SPI6/
2/SAI4/
1/OCTO
OCTO
SPI3/
UART7/
OTG1_HS/ SWPMI1/
x/TIM2x
2/15
3/I2S3/
UART4/5/ SDMMC2/
SPIM_P1 SPIM_P1
I2S3/
USART1/
SAI4/
TIM1x/TIM
SPI4/5/6
8
SPDIFRX1
/2/TIM8
/TIM15/
UART4
2/3/6
SDMMC2/ 8/UART7/9/
/TIM13/14
USART1/
TIM8
USART10
10
AF12
AF13
AF14
AF15
FMC/LCD/
MDIOS/
OCTOSPI
M_P1/
SDMMC1/
TIM1x/
TIM8
COMP/
DCMI/
PSSI/
LCD/
TIM1x/
TIM23
LCD/
TIM24/
UART5
SYS
73/236
PA0
-
TIM2_CH
1/TIM2_
ETR
TIM5_CH1
TIM8_
ETR
TIM15_
BKIN
SPI6_
NSS/I2S
6_WS
-
USART2
_CTS/
USART2
_NSS
UART4_
TX
SDMMC2_
CMD
SAI4_SD_
B
ETH_MII_
CRS
FMC_A19
-
-
EVENT
OUT
PA1
-
TIM2_CH
2
TIM5_CH2
LPTIM3_
OUT
TIM15_
CH1N
-
-
USART2
_RTS/
USART2
_DE
UART4_
RX
OCTOSPI
M_P1_IO3
SAI4_
MCLK_B
ETH_MII_
RX_CLK/
ETH_RMII_
REF_CLK
OCTOSPI
M_P1_
DQS
-
LCD_
R2
EVENT
OUT
PA2
-
TIM2_CH
3
TIM5_CH3
LPTIM4_
OUT
TIM15_
CH1
-
OCTOSPI
M_P1_IO0
USART2
_TX
SAI4_SCK
_B
-
-
ETH_MDIO
MDIOS_
MDIO
-
LCD_R
1
EVENT
OUT
PA3
-
TIM2_CH
4
TIM5_CH4
LPTIM5_
OUT
TIM15_
CH2
I2S6_
MCK
OCTOSPI
M_P1_IO2
USART2
_RX
-
LCD_B2
OTG_HS_
ULPI_D0
ETH_MII_
COL
OCTOSPI
M_P1_
CLK
-
LCD_B
5
EVENT
OUT
PA4
D1PWR
EN
-
TIM5_
ETR
-
-
SPI1_
SPI3_NSS
NSS/
/I2S3_WS
I2S1_WS
USART2
_CK
SPI6_NSS
/I2S6_WS
-
-
-
FMC_D8/
FMC_AD8
DCMI_
HSYNC/
PSSI_DE
LCD_
VSYNC
EVENT
OUT
PA5
D2PWR
EN
TIM2_CH
1/TIM2_
ETR
-
TIM8_CH
1N
-
SPI1_
SCK/
I2S1_CK
-
SPI6_SCK
/I2S6_CK
-
OTG_HS_
ULPI_CK
-
FMC_D9/
FMC_AD9
PSSI_D1
4
LCD_R
4
EVENT
OUT
PA6
-
TIM1_
BKIN
TIM3_CH1
TIM8_
BKIN
-
SPI1_
OCTOSPI
MISO/
M_P1_IO3
I2S1_SDI
-
SPI6_
TIM13_CH
MISO/I2S6
1
_SDI
TIM8_
BKIN_
COMP12
MDIOS_
MDC
TIM1_
BKIN_
COMP12
DCMI_
PIXCLK/
PSSI_
PDCK
LCD_G
2
EVENT
OUT
PA7
-
TIM1_CH
1N
TIM3_CH2
TIM8_CH
1N
-
SPI1_
MOSI/I2S
1_SDO
-
SPI6_
TIM14_CH
MOSI/I2S6
1
_SDO
OCTOSPI
M_P1_IO2
ETH_MII_
RX_DV/
ETH_RMII_
CRS_DV
FMC_SDN
WE
-
LCD_
VSYNC
EVENT
OUT
-
-
Pinouts, pin descriptions and alternate functions
DS13314 Rev 3
Port A
AF1
STM32H733xG
Table 8. STM32H733 pin alternate functions
AF0
Port
SYS
AF1
AF2
AF3
AF4
AF5
AF6
AF7
AF8
AF9
AF10
AF11
CEC/
DCMI/
CRS/
DFSDM1/
FDCAN1/2
DFSDM1
PSSI/
DFSDM1/I SDMMC1
FMC/
ETH/I2C4/
CEC/
LPUART1/
/FMC/
/LCD/
DFSDM1
2C4/5/
/SPI2/I2S
LCD/
LCD/MDIO
FMC/
FDCAN3/
FDCAN3/
SAI4/
LCD/
LPTIM2/ /I2C1/2/3/
OCTO
2/SPI3/
OCTO
S/OCTOSP
LPTIM1/
PDM_
SPI1/I2S
SDMMC1/
OCTO
3/4/5/
4/5/
SPIM_P1/
I2S3/
SPIM_P1/
IM_P1/
SAI4/TIM1
SAI1/
1/SPI2/
SPDIFRX1 SPIM_P1/
LPUART LPTIM2/
SAI1/
SPI6/
OTG1_FS/ SDMMC2/
6/17/TIM1 TIM3/4/5/1
I2S2/SPI
/SPI6/
2/SAI4/
1/OCTO
OCTO
SPI3/
UART7/
OTG1_HS/ SWPMI1/
x/TIM2x
2/15
3/I2S3/
UART4/5/ SDMMC2/
SPIM_P1 SPIM_P1
I2S3/
USART1/
SAI4/
TIM1x/TIM
SPI4/5/6
8
SPDIFRX1
/2/TIM8
/TIM15/
UART4
2/3/6
SDMMC2/ 8/UART7/9/
/TIM13/14
USART1/
TIM8
USART10
10
AF12
AF13
AF14
AF15
FMC/LCD/
MDIOS/
OCTOSPI
M_P1/
SDMMC1/
TIM1x/
TIM8
COMP/
DCMI/
PSSI/
LCD/
TIM1x/
TIM23
LCD/
TIM24/
UART5
SYS
MCO1
TIM1_CH
1
-
TIM8_
BKIN2
I2C3_
SCL
-
I2C5_SCL
USART1
_CK
-
-
OTG_HS_
SOF
UART7_RX
TIM8_
BKIN2_
COMP12
LCD_B3
LCD_R
6
EVENT
OUT
PA9
-
TIM1_CH
2
-
LPUART
1_TX
I2C3_
SMBA
SPI2_
SCK/
I2S2_CK
I2C5_
SMBA
USART1
_TX
-
-
-
ETH_TX_
ER
-
DCMI_
D0/PSSI
_D0
LCD_R
5
EVENT
OUT
PA10
-
TIM1_CH
3
-
LPUART
1_RX
-
-
-
USART1
_RX
-
-
OTG_HS_
ID
MDIOS_
MDIO
LCD_B4
DCMI_
D1/PSSI
_D1
LCD_B
1
EVENT
OUT
PA11
-
TIM1_CH
4
-
LPUART
1_CTS
-
SPI2_
NSS/
I2S2_WS
UART4_
RX
USART1
_CTS/
USART1
_NSS
-
FDCAN1_
RX
-
-
-
-
LCD_R
4
EVENT
OUT
PA12
-
TIM1_
ETR
-
LPUART
1_RTS/
LPUART
1_DE
-
SPI2_
SCK/
I2S2_CK
UART4_
TX
USART1
_RTS/
USART1
_DE
SAI4_FS_
B
FDCAN1_
TX
-
-
TIM1_
BKIN2
-
LCD_R
5
EVENT
OUT
PA13
JTMS/
SWDIO
-
-
-
-
-
-
-
-
-
-
-
-
-
-
EVENT
OUT
PA14
JTCK/
SWCLK
-
-
-
-
-
-
-
-
-
-
-
-
-
-
EVENT
OUT
PA15
JTDI
TIM2_
CH1/TIM2
_ETR
-
-
CEC
UART4_
RTS/
UART4_
DE
LCD_R3
-
UART7_TX
-
-
LCD_B
6
EVENT
OUT
Port A
DS13314 Rev 3
PA8
SPI1_
SPI6_
SPI3_NSS
NSS/
NSS/
/I2S3_WS
I2S1_WS
I2S6_WS
Pinouts, pin descriptions and alternate functions
74/236
Table 8. STM32H733 pin alternate functions (continued)
STM32H733xG
AF0
Port
SYS
AF2
AF3
AF4
AF5
AF6
AF7
AF8
AF9
AF10
AF11
CEC/
DCMI/
CRS/
DFSDM1/
FDCAN1/2
DFSDM1
PSSI/
DFSDM1/I SDMMC1
FMC/
ETH/I2C4/
CEC/
LPUART1/
/FMC/
/LCD/
DFSDM1
2C4/5/
/SPI2/I2S
LCD/
LCD/MDIO
FMC/
FDCAN3/
FDCAN3/
SAI4/
LCD/
LPTIM2/ /I2C1/2/3/
OCTO
2/SPI3/
OCTO
S/OCTOSP
LPTIM1/
PDM_
SPI1/I2S
SDMMC1/
OCTO
3/4/5/
4/5/
SPIM_P1/
I2S3/
SPIM_P1/
IM_P1/
SAI4/TIM1
SAI1/
1/SPI2/
SPDIFRX1 SPIM_P1/
LPUART LPTIM2/
SAI1/
SPI6/
OTG1_FS/ SDMMC2/
6/17/TIM1 TIM3/4/5/1
I2S2/SPI
/SPI6/
2/SAI4/
1/OCTO
OCTO
SPI3/
UART7/
OTG1_HS/ SWPMI1/
x/TIM2x
2/15
3/I2S3/
UART4/5/ SDMMC2/
SPIM_P1 SPIM_P1
I2S3/
USART1/
SAI4/
TIM1x/TIM
SPI4/5/6
8
SPDIFRX1
/2/TIM8
/TIM15/
UART4
2/3/6
SDMMC2/ 8/UART7/9/
/TIM13/14
USART1/
TIM8
USART10
10
AF12
AF13
AF14
AF15
FMC/LCD/
MDIOS/
OCTOSPI
M_P1/
SDMMC1/
TIM1x/
TIM8
COMP/
DCMI/
PSSI/
LCD/
TIM1x/
TIM23
LCD/
TIM24/
UART5
SYS
75/236
PB0
-
TIM1_CH
2N
TIM3_CH3
OCTO
TIM8_CH
SPIM_P1
2N
_IO1
-
DFSDM1_
CKOUT
-
UART4_
CTS
LCD_R3
OTG_HS_
ULPI_D1
ETH_MII_
RXD2
-
-
LCD_G
1
EVENT
OUT
PB1
-
TIM1_CH
3N
TIM3_CH4
OCTO
TIM8_CH
SPIM_P1
3N
_IO0
-
DFSDM1_
DATIN1
-
-
LCD_R6
OTG_HS_
ULPI_D2
ETH_MII_
RXD3
-
-
LCD_G
0
EVENT
OUT
PB2
RTC_
OUT
SAI4_D1
SAI1_D1
-
DFSDM1
_CKIN1
-
SPI3_
SAI1_SD_
SAI4_SD_
MOSI/I2S
A
A
3_SDO
OCTO
SPIM_P1_
CLK
OCTO
SPIM_P1_
DQS
ETH_TX_
ER
-
TIM23_
ETR
-
EVENT
OUT
PB3
JTDO/
TRACE
SWO
TIM2_CH
2
-
-
-
SPI1_
SCK/
I2S1_CK
SPI3_SCK
/I2S3_CK
-
CRS_
SYNC
UART7_RX
-
-
TIM24_
ETR
EVENT
OUT
PB4
NJT
RST
TIM16_
BKIN
TIM3_CH1
-
-
SPI1_
MISO/
I2S1_SDI
SPI3_
MISO/
I2S3_SDI
SPI2_
NSS/
I2S2_WS
SDMMC2_
D3
-
UART7_TX
-
-
-
EVENT
OUT
PB5
-
TIM17_
BKIN
TIM3_CH2
LCD_B5
I2C1_
SMBA
SPI1_
MOSI/I2S
1_SDO
I2C4_
SMBA
SPI3_
SPI6_
MOSI/I2S MOSI/I2S6
3_SDO
_SDO
FDCAN2_
RX
OTG_HS_
ULPI_D7
ETH_PPS_
OUT
FMC_SDC
KE1
DCMI_
D10/PSS
I_D10
UART5
_RX
EVENT
OUT
PB6
-
TIM16_
CH1N
TIM4_CH1
-
I2C1_
SCL
CEC
I2C4_SCL
USART1
_TX
LPUART1
_TX
FDCAN2_
TX
OCTO
SPIM_P1_
NCS
DFSDM1_
DATIN5
FMC_SDN
E1
DCMI_
D5/PSSI
_D5
UART5
_TX
EVENT
OUT
PB7
-
TIM17_
CH1N
TIM4_CH2
-
I2C1_
SDA
-
I2C4_SDA
USART1
_RX
LPUART1
_RX
-
-
DFSDM1_
CKIN5
FMC_NL
DCMI_
VSYNC/
PSSI_
RDY
-
EVENT
OUT
PB8
-
TIM16_C
H1
TIM4_CH3
DFSDM1
_CKIN7
I2C1_
SCL
-
I2C4_SCL
SDMMC1
_CKIN
UART4_
RX
FDCAN1_
RX
SDMMC2_
D4
ETH_MII_
TXD3
SDMMC1_
D4
DCMI_
D6/PSSI
_D6
LCD_B
6
EVENT
OUT
PB9
-
TIM17_
CH1
TIM4_CH4
DFSDM1
_DATIN7
I2C1_
SDA
SPI2_
NSS/I2S
2_WS
I2C4_SDA
SDMMC1
_CDIR
UART4_
TX
FDCAN1_
TX
SDMMC2_
D5
I2C4_
SMBA
SDMMC1_
D5
DCMI_
D7/PSSI
_D7
LCD_B
7
EVENT
OUT
SPI6_SCK SDMMC2_
/I2S6_CK
D2
SPI6_
MISO/
I2S6_SDI
Pinouts, pin descriptions and alternate functions
DS13314 Rev 3
Port B
AF1
STM32H733xG
Table 8. STM32H733 pin alternate functions (continued)
AF0
Port
SYS
AF1
AF2
AF3
AF4
AF5
AF6
AF7
AF8
AF9
AF10
AF11
CEC/
DCMI/
CRS/
DFSDM1/
FDCAN1/2
DFSDM1
PSSI/
DFSDM1/I SDMMC1
FMC/
ETH/I2C4/
CEC/
LPUART1/
/FMC/
/LCD/
DFSDM1
2C4/5/
/SPI2/I2S
LCD/
LCD/MDIO
FMC/
FDCAN3/
FDCAN3/
SAI4/
LCD/
LPTIM2/ /I2C1/2/3/
OCTO
2/SPI3/
OCTO
S/OCTOSP
LPTIM1/
PDM_
SPI1/I2S
SDMMC1/
OCTO
3/4/5/
4/5/
SPIM_P1/
I2S3/
SPIM_P1/
IM_P1/
SAI4/TIM1
SAI1/
1/SPI2/
SPDIFRX1 SPIM_P1/
LPUART LPTIM2/
SAI1/
SPI6/
OTG1_FS/ SDMMC2/
6/17/TIM1 TIM3/4/5/1
I2S2/SPI
/SPI6/
2/SAI4/
1/OCTO
OCTO
SPI3/
UART7/
OTG1_HS/ SWPMI1/
x/TIM2x
2/15
3/I2S3/
UART4/5/ SDMMC2/
SPIM_P1 SPIM_P1
I2S3/
USART1/
SAI4/
TIM1x/TIM
SPI4/5/6
8
SPDIFRX1
/2/TIM8
/TIM15/
UART4
2/3/6
SDMMC2/ 8/UART7/9/
/TIM13/14
USART1/
TIM8
USART10
10
AF12
AF13
AF14
AF15
FMC/LCD/
MDIOS/
OCTOSPI
M_P1/
SDMMC1/
TIM1x/
TIM8
COMP/
DCMI/
PSSI/
LCD/
TIM1x/
TIM23
LCD/
TIM24/
UART5
SYS
-
TIM2_CH
3
-
LPTIM2_
IN1
I2C2_
SCL
SPI2_
SCK/
I2S2_CK
DFSDM1_
DATIN7
USART3
_TX
-
OCTO
SPIM_P1_
NCS
OTG_HS_
ULPI_D3
ETH_MII_
RX_ER
-
-
LCD_G
4
EVENT
OUT
PB11
-
TIM2_CH
4
-
LPTIM2_
ETR
I2C2_
SDA
-
DFSDM1_
CKIN7
USART3
_RX
-
-
OTG_HS_
ULPI_D4
ETH_MII_
TX_EN/
ETH_RMII_
TX_EN
-
-
LCD_G
5
EVENT
OUT
PB12
-
TIM1_BKI
N
-
OCTO
SPIM_P1
_NCLK
I2C2_SM
BA
SPI2_
NSS/
I2S2_WS
DFSDM1_
DATIN1
USART3
_CK
-
FDCAN2_
RX
OTG_HS_
ULPI_D5
ETH_MII_
TXD0/
ETH_RMII_
TXD0
OCTOSPI
M_P1_IO0
TIM1_
BKIN_
COMP12
UART5
_RX
EVENT
OUT
PB13
-
TIM1_CH
1N
-
LPTIM2_
OUT
OCTO
SPIM_P1
_IO2
SPI2_
SCK/
I2S2_CK
DFSDM1_
CKIN1
USART3
_CTS/
USART3
_NSS
-
FDCAN2_
TX
OTG_HS_
ULPI_D6
ETH_MII_
TXD1/
ETH_RMII_
TXD1
SDMMC1_
D0
DCMI_
D2/PSSI
_D2
UART5
_TX
EVENT
OUT
PB14
-
TIM1_CH
2N
TIM12_CH TIM8_CH
1
2N
USART1
_TX
SPI2_
DFSDM1_
MISO/
DATIN2
I2S2_SDI
USART3
_RTS/
USART3
_DE
UART4_
RTS/UAR
T4_DE
SDMMC2_
D0
-
-
FMC_D10/
FMC_
AD10
-
LCD_C
LK
EVENT
OUT
PB15
RTC_
REFIN
TIM1_CH
3N
TIM12_CH TIM8_CH
2
3N
USART1
_RX
SPI2_
DFSDM1_
MOSI/I2S
CKIN2
2_SDO
-
UART4_
CTS
SDMMC2_
D1
-
-
FMC_D11/
FMC_AD1
1
-
LCD_G
7
EVENT
OUT
Port B
DS13314 Rev 3
PB10
Pinouts, pin descriptions and alternate functions
76/236
Table 8. STM32H733 pin alternate functions (continued)
STM32H733xG
AF0
Port
SYS
AF2
AF3
AF4
AF12
AF13
AF14
AF15
CEC/
DCMI/
CRS/
DFSDM1/
FDCAN1/2
DFSDM1
PSSI/
DFSDM1/I SDMMC1
FMC/
ETH/I2C4/
CEC/
LPUART1/
/FMC/
/LCD/
DFSDM1
2C4/5/
/SPI2/I2S
LCD/
LCD/MDIO
FMC/
FDCAN3/
FDCAN3/
SAI4/
LCD/
LPTIM2/ /I2C1/2/3/
OCTO
2/SPI3/
OCTO
S/OCTOSP
LPTIM1/
PDM_
SPI1/I2S
SDMMC1/
OCTO
3/4/5/
4/5/
SPIM_P1/
I2S3/
SPIM_P1/
IM_P1/
SAI4/TIM1
SAI1/
1/SPI2/
SPDIFRX1 SPIM_P1/
LPUART LPTIM2/
SAI1/
SPI6/
OTG1_FS/ SDMMC2/
6/17/TIM1 TIM3/4/5/1
I2S2/SPI
/SPI6/
2/SAI4/
1/OCTO
OCTO
SPI3/
UART7/
OTG1_HS/ SWPMI1/
x/TIM2x
2/15
3/I2S3/
UART4/5/ SDMMC2/
SPIM_P1 SPIM_P1
I2S3/
USART1/
SAI4/
TIM1x/TIM
SPI4/5/6
8
SPDIFRX1
/2/TIM8
/TIM15/
UART4
2/3/6
SDMMC2/ 8/UART7/9/
/TIM13/14
USART1/
TIM8
USART10
10
FMC/LCD/
MDIOS/
OCTOSPI
M_P1/
SDMMC1/
TIM1x/
TIM8
COMP/
DCMI/
PSSI/
LCD/
TIM1x/
TIM23
LCD/
TIM24/
UART5
SYS
PC0
-
FMC_D12
/FMC_AD
12
-
DFSDM1
_CKIN0
-
PC1
TRACE
D0
SAI4_D1
SAI1_D1
DFSDM1
_DATIN0
DFSDM1
_CKIN4
PC2
PWR_
DEEP
SLEEP
-
-
PC3
PWR_
SLEEP
-
PC4
PWR_
DEEP
SLEEP
PC5
AF5
AF6
AF7
AF8
AF9
AF10
AF11
DFSDM1_
DATIN4
-
SAI4_FS_
B
FMC_A25
OTG_HS_
ULPI_STP
LCD_G2
FMC_SDN
WE
-
LCD_R
5
EVENT
OUT
SPI2_
SAI1_SD_
MOSI/I2S
A
2_SDO
-
SAI4_SD_ SDMMC2_
A
CK
OCTO
SPIM_P1_
IO4
ETH_MDC
MDIOS_
MDC
-
LCD_G
5
EVENT
OUT
DFSDM1
_CKIN1
OCTO
SPI2_
DFSDM1_
SPIM_P1 MISO/I2S
CKOUT
_IO5
2_SDI
-
-
OCTOSPI
M_P1_IO2
OTG_HS_
ULPI_DIR
ETH_MII_
TXD2
FMC_SDN
E0
-
-
EVENT
OUT
-
DFSDM1
_DATIN1
OCTO
SPI2_
SPIM_P1 MOSI/I2S
_IO6
2_SDO
-
-
-
OCTOSPI
M_P1_IO0
OTG_HS_
ULPI_NXT
ETH_MII_
TX_CLK
FMC_SDC
KE0
-
-
EVENT
OUT
FMC_A22
-
DFSDM1
_CKIN2
-
I2S1_
MCK
-
-
-
ETH_MII_
SPDIFRX1 SDMMC2_ RXD0/ETH
_IN3
CKIN
_RMII_RXD
0
FMC_SDN
E0
-
LCD_R
7
EVENT
OUT
PWR_
SLEEP
SAI4_D3
SAI1_D3
DFSDM1
_DATIN2
PSSI_D1
5
-
-
-
-
SPDIFRX1
_IN4
OCTOSPI
M_P1_DQ
S
ETH_MII_R
XD1/ETH_
RMII_RXD1
FMC_SDC
KE0
COMP1_
OUT
LCD_D
E
EVENT
OUT
PC6
-
-
TIM3_CH1
TIM8_CH
1
DFSDM1
_CKIN3
I2S2_
MCK
-
USART6
_TX
SDMMC1_
D0DIR
FMC_
NWAIT
SDMMC2_
D6
-
SDMMC1_
D6
DCMI_
D0/PSSI
_D0
LCD_H
SYNC
EVENT
OUT
PC7
DB
TRGIO
-
TIM3_CH2
TIM8_CH
2
DFSDM1
_DATIN3
-
I2S3_
MCK
USART6
_RX
SDMMC1_
FMC_NE1
D123DIR
SDMMC2_
D7
SWPMI_TX
SDMMC1_
D7
DCMI_
D1/PSSI
_D1
LCD_G
6
EVENT
OUT
PC8
TRACE
D1
-
TIM3_CH3
TIM8_CH
3
-
-
-
USART6
_CK
FMC_INT
SWPMI_RX
SDMMC1_
D0
DCMI_
D2/PSSI
_D2
-
EVENT
OUT
-
UART5_
RTS/
UART5_
DE
FMC_NE2
/FMC_
NCE
77/236
Pinouts, pin descriptions and alternate functions
DS13314 Rev 3
Port C
AF1
STM32H733xG
Table 8. STM32H733 pin alternate functions (continued)
AF0
Port
DS13314 Rev 3
Port C
SYS
AF1
AF2
AF3
AF4
AF5
AF6
AF7
AF8
AF9
AF10
AF11
CEC/
DCMI/
CRS/
DFSDM1/
FDCAN1/2
DFSDM1
PSSI/
DFSDM1/I SDMMC1
FMC/
ETH/I2C4/
CEC/
LPUART1/
/FMC/
/LCD/
DFSDM1
2C4/5/
/SPI2/I2S
LCD/
LCD/MDIO
FMC/
FDCAN3/
FDCAN3/
SAI4/
LCD/
LPTIM2/ /I2C1/2/3/
OCTO
2/SPI3/
OCTO
S/OCTOSP
LPTIM1/
PDM_
SPI1/I2S
SDMMC1/
OCTO
3/4/5/
4/5/
SPIM_P1/
I2S3/
SPIM_P1/
IM_P1/
SAI4/TIM1
SAI1/
1/SPI2/
SPDIFRX1 SPIM_P1/
LPUART LPTIM2/
SAI1/
SPI6/
OTG1_FS/ SDMMC2/
6/17/TIM1 TIM3/4/5/1
I2S2/SPI
/SPI6/
2/SAI4/
1/OCTO
OCTO
SPI3/
UART7/
OTG1_HS/ SWPMI1/
x/TIM2x
2/15
3/I2S3/
UART4/5/ SDMMC2/
SPIM_P1 SPIM_P1
I2S3/
USART1/
SAI4/
TIM1x/TIM
SPI4/5/6
8
SPDIFRX1
/2/TIM8
/TIM15/
UART4
2/3/6
SDMMC2/ 8/UART7/9/
/TIM13/14
USART1/
TIM8
USART10
10
AF12
AF13
AF14
AF15
FMC/LCD/
MDIOS/
OCTOSPI
M_P1/
SDMMC1/
TIM1x/
TIM8
COMP/
DCMI/
PSSI/
LCD/
TIM1x/
TIM23
LCD/
TIM24/
UART5
SYS
PC9
MCO2
-
TIM3_CH4
TIM8_CH
4
I2C3_
SDA
I2S_
CKIN
I2C5_SDA
-
UART5_C
TS
OCTO
SPIM_P1_
IO0
LCD_G3
SWPMI_
SUSPEND
SDMMC1_
D1
DCMI_D
3/PSSI_
D3
LCD_B
2
EVENT
OUT
PC10
-
-
-
DFSDM1
_CKIN5
I2C5_
SDA
-
SPI3_SCK
/I2S3_CK
USART3
_TX
UART4_
TX
OCTO
SPIM_P1_
IO1
LCD_B1
SWPMI_RX
SDMMC1_
D2
DCMI_D
8/PSSI_
D8
LCD_R
2
EVENT
OUT
PC11
-
-
-
DFSDM1
_DATIN5
I2C5_
SCL
-
SPI3_
MISO/
I2S3_SDI
USART3
_RX
UART4_
RX
OCTO
SPIM_P1_
NCS
-
-
SDMMC1_
D3
DCMI_
D4/PSSI
_D4
LCD_B
4
EVENT
OUT
PC12
TRACE
D3
-
I2C5_
SMBA
SPI6_
SCK/
I2S6_CK
SPI3_
MOSI/
I2S3_SDO
USART3
_CK
UART5_
TX
-
-
-
SDMMC1_
CK
DCMI_
D9/PSSI
_D9
LCD_R
6
EVENT
OUT
PC13
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
EVENT
OUT
PC14
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
EVENT
OUT
PC15
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
EVENT
OUT
FMC_D6/ TIM15_CH
FMC_AD6
1
Pinouts, pin descriptions and alternate functions
78/236
Table 8. STM32H733 pin alternate functions (continued)
STM32H733xG
AF0
Port
SYS
AF2
AF3
AF4
AF5
AF6
AF7
AF8
AF9
AF10
AF11
CEC/
DCMI/
CRS/
DFSDM1/
FDCAN1/2
DFSDM1
PSSI/
DFSDM1/I SDMMC1
FMC/
ETH/I2C4/
CEC/
LPUART1/
/FMC/
/LCD/
DFSDM1
2C4/5/
/SPI2/I2S
LCD/
LCD/MDIO
FMC/
FDCAN3/
FDCAN3/
SAI4/
LCD/
LPTIM2/ /I2C1/2/3/
OCTO
2/SPI3/
OCTO
S/OCTOSP
LPTIM1/
PDM_
SPI1/I2S
SDMMC1/
OCTO
3/4/5/
4/5/
SPIM_P1/
I2S3/
SPIM_P1/
IM_P1/
SAI4/TIM1
SAI1/
1/SPI2/
SPDIFRX1 SPIM_P1/
LPUART LPTIM2/
SAI1/
SPI6/
OTG1_FS/ SDMMC2/
6/17/TIM1 TIM3/4/5/1
I2S2/SPI
/SPI6/
2/SAI4/
1/OCTO
OCTO
SPI3/
UART7/
OTG1_HS/ SWPMI1/
x/TIM2x
2/15
3/I2S3/
UART4/5/ SDMMC2/
SPIM_P1 SPIM_P1
I2S3/
USART1/
SAI4/
TIM1x/TIM
SPI4/5/6
8
SPDIFRX1
/2/TIM8
/TIM15/
UART4
2/3/6
SDMMC2/ 8/UART7/9/
/TIM13/14
USART1/
TIM8
USART10
10
AF12
AF13
AF14
AF15
FMC/LCD/
MDIOS/
OCTOSPI
M_P1/
SDMMC1/
TIM1x/
TIM8
COMP/
DCMI/
PSSI/
LCD/
TIM1x/
TIM23
LCD/
TIM24/
UART5
SYS
PD0
-
-
-
DFSDM1
_CKIN6
-
-
-
-
UART4_
RX
FDCAN1_
RX
-
UART9_
CTS
FMC_D2/
FMC_AD2
-
LCD_B
1
EVENT
OUT
PD1
-
-
-
DFSDM1
_DATIN6
-
-
-
-
UART4_
TX
FDCAN1_
TX
-
-
FMC_D3/
FMC_AD3
-
-
EVENT
OUT
PD2
TRACE
D2
FMC_D7/
FMC_AD7
TIM3_
ETR
-
TIM15_
BKIN
-
-
-
UART5_
RX
LCD_B7
-
-
SDMMC1_
CMD
DCMI_
D11/PSSI
_D11
LCD_B
2
EVENT
OUT
PD3
-
-
-
DFSDM1
_CKOUT
-
SPI2_
SCK/
I2S2_CK
-
USART2
_CTS/
USART2
_NSS
-
-
-
-
FMC_CLK
DCMI_
D5/PSSI
_D5
LCD_G
7
EVENT
OUT
PD4
-
-
-
-
-
-
-
USART2
_RTS/
USART2
_DE
-
-
OCTOSPI
M_P1_IO4
-
FMC_NOE
-
-
EVENT
OUT
PD5
-
-
-
-
-
-
-
USART2
_TX
-
-
OCTOSPI
M_P1_IO5
-
FMC_NWE
-
-
EVENT
OUT
PD6
-
SAI4_D1
SAI1_D1
DFSDM1
_CKIN4
DFSDM1
_DATIN1
SPI3_
SAI1_SD_
MOSI/I2S
A
3_SDO
USART2
_RX
SAI4_SD_
A
-
OCTO
SPIM_P1_
IO6
SDMMC2_
CK
FMC_
NWAIT
DCMI_D
10/PSSI_
D10
LCD_B
2
EVENT
OUT
PD7
-
-
-
DFSDM1
_DATIN4
-
SPI1_
DFSDM1_
MOSI/I2S
CKIN1
1_SDO
USART2
_CK
-
SPDIFRX1
_IN1
OCTO
SPIM_P1_
IO7
SDMMC2_
CMD
FMC_NE1
-
-
EVENT
OUT
PD8
-
-
-
DFSDM1
_CKIN3
-
USART3
_TX
-
SPDIFRX1
_IN2
-
-
FMC_D13/
FMC_
AD13
-
-
EVENT
OUT
-
-
79/236
Pinouts, pin descriptions and alternate functions
DS13314 Rev 3
Port D
AF1
STM32H733xG
Table 8. STM32H733 pin alternate functions (continued)
AF0
Port
DS13314 Rev 3
Port D
SYS
AF1
AF2
AF3
AF4
AF5
AF6
AF7
AF8
AF9
AF10
AF11
CEC/
DCMI/
CRS/
DFSDM1/
FDCAN1/2
DFSDM1
PSSI/
DFSDM1/I SDMMC1
FMC/
ETH/I2C4/
CEC/
LPUART1/
/FMC/
/LCD/
DFSDM1
2C4/5/
/SPI2/I2S
LCD/
LCD/MDIO
FMC/
FDCAN3/
FDCAN3/
SAI4/
LCD/
LPTIM2/ /I2C1/2/3/
OCTO
2/SPI3/
OCTO
S/OCTOSP
LPTIM1/
PDM_
SPI1/I2S
SDMMC1/
OCTO
3/4/5/
4/5/
SPIM_P1/
I2S3/
SPIM_P1/
IM_P1/
SAI4/TIM1
SAI1/
1/SPI2/
SPDIFRX1 SPIM_P1/
LPUART LPTIM2/
SAI1/
SPI6/
OTG1_FS/ SDMMC2/
6/17/TIM1 TIM3/4/5/1
I2S2/SPI
/SPI6/
2/SAI4/
1/OCTO
OCTO
SPI3/
UART7/
OTG1_HS/ SWPMI1/
x/TIM2x
2/15
3/I2S3/
UART4/5/ SDMMC2/
SPIM_P1 SPIM_P1
I2S3/
USART1/
SAI4/
TIM1x/TIM
SPI4/5/6
8
SPDIFRX1
/2/TIM8
/TIM15/
UART4
2/3/6
SDMMC2/ 8/UART7/9/
/TIM13/14
USART1/
TIM8
USART10
10
AF12
AF13
AF14
AF15
FMC/LCD/
MDIOS/
OCTOSPI
M_P1/
SDMMC1/
TIM1x/
TIM8
COMP/
DCMI/
PSSI/
LCD/
TIM1x/
TIM23
LCD/
TIM24/
UART5
SYS
PD9
-
-
-
DFSDM1
_DATIN3
-
-
-
USART3
_RX
-
-
-
-
FMC_D14/
FMC_AD1
4
-
-
EVENT
OUT
PD10
-
-
-
DFSDM1
_CKOUT
-
-
-
USART3
_CK
-
-
-
-
FMC_D15/
FMC_AD1
5
-
LCD_B
3
EVENT
OUT
PD11
-
-
-
LPTIM2_I I2C4_SM
N2
BA
-
-
USART3
_CTS/
USART3
_NSS
-
OCTOSPI
M_P1_IO0
SAI4_SD_
A
-
FMC_A16/
FMC_CLE
-
-
EVENT
OUT
PD12
-
LPTIM1_
IN1
TIM4_CH1
LPTIM2_
IN1
I2C4_
SCL
FDCAN3
_RX
-
USART3
_RTS/
USART3
_DE
-
OCTO
SPIM_P1_
IO1
SAI4_FS_
A
-
FMC_A17/
FMC_ALE
DCMI_
D12/PSS
I_D12
-
EVENT
OUT
PD13
-
LPTIM1_
OUT
TIM4_CH2
-
I2C4_
SDA
FDCAN3
_TX
-
-
-
OCTO
SPIM_P1_
IO3
SAI4_
SCK_A
UART9_
RTS/
UART9_DE
FMC_A18
DCMI_
D13/
PSSI_
D13
-
EVENT
OUT
PD14
-
-
TIM4_CH3
-
-
-
-
-
UART8_
CTS
-
-
UART9_RX
FMC_D0/
FMC_AD0
-
-
EVENT
OUT
PD15
-
-
TIM4_CH4
-
-
-
-
-
UART8_
RTS/
UART8_
DE
-
-
UART9_TX
FMC_D1/
FMC_AD1
-
-
EVENT
OUT
Pinouts, pin descriptions and alternate functions
80/236
Table 8. STM32H733 pin alternate functions (continued)
STM32H733xG
AF0
Port
SYS
AF2
AF3
AF4
AF5
AF6
AF7
AF8
AF9
AF10
AF11
CEC/
DCMI/
CRS/
DFSDM1/
FDCAN1/2
DFSDM1
PSSI/
DFSDM1/I SDMMC1
FMC/
ETH/I2C4/
CEC/
LPUART1/
/FMC/
/LCD/
DFSDM1
2C4/5/
/SPI2/I2S
LCD/
LCD/MDIO
FMC/
FDCAN3/
FDCAN3/
SAI4/
LCD/
LPTIM2/ /I2C1/2/3/
OCTO
2/SPI3/
OCTO
S/OCTOSP
LPTIM1/
PDM_
SPI1/I2S
SDMMC1/
OCTO
3/4/5/
4/5/
SPIM_P1/
I2S3/
SPIM_P1/
IM_P1/
SAI4/TIM1
SAI1/
1/SPI2/
SPDIFRX1 SPIM_P1/
LPUART LPTIM2/
SAI1/
SPI6/
OTG1_FS/ SDMMC2/
6/17/TIM1 TIM3/4/5/1
I2S2/SPI
/SPI6/
2/SAI4/
1/OCTO
OCTO
SPI3/
UART7/
OTG1_HS/ SWPMI1/
x/TIM2x
2/15
3/I2S3/
UART4/5/ SDMMC2/
SPIM_P1 SPIM_P1
I2S3/
USART1/
SAI4/
TIM1x/TIM
SPI4/5/6
8
SPDIFRX1
/2/TIM8
/TIM15/
UART4
2/3/6
SDMMC2/ 8/UART7/9/
/TIM13/14
USART1/
TIM8
USART10
10
AF12
AF13
AF14
AF15
FMC/LCD/
MDIOS/
OCTOSPI
M_P1/
SDMMC1/
TIM1x/
TIM8
COMP/
DCMI/
PSSI/
LCD/
TIM1x/
TIM23
LCD/
TIM24/
UART5
SYS
81/236
PE0
-
LPTIM1_
ETR
TIM4_
ETR
-
LPTIM2_
ETR
-
-
-
UART8_
RX
-
SAI4_
MCLK_A
-
FMC_NBL
0
DCMI_
D2/PSSI
_D2
LCD_R
0
EVENT
OUT
PE1
-
LPTIM1_
IN2
-
-
-
-
-
-
UART8_
TX
-
-
-
FMC_NBL
1
DCMI_
D3/
PSSI_D3
LCD_R
6
EVENT
OUT
PE2
TRACE
CLK
-
SAI1_
CK1
-
USART1
0_RX
SPI4_
SCK
SAI1_
MCLK_A
-
SAI4_
MCLK_A
OCTOSPI
M_P1_IO2
SAI4_CK1
ETH_MII_
TXD3
FMC_A23
-
-
EVENT
OUT
PE3
TRACE
D0
-
-
-
TIM15_
BKIN
-
SAI1_SD_
B
-
SAI4_SD_
B
-
-
USART10_
TX
FMC_A19
-
-
EVENT
OUT
PE4
TRACE
D1
-
SAI1_D2
DFSDM1
_DATIN3
TIM15_
CH1N
SPI4_NS
S
SAI1_FS_
A
-
SAI4_FS_
A
-
SAI4_D2
-
FMC_A20
DCMI_
D4/PSSI
_D4
LCD_B
0
EVENT
OUT
PE5
TRACE
D2
-
SAI1_CK2
DFSDM1
_CKIN3
TIM15_
CH1
SPI4_
MISO
SAI1_SCK
_A
-
SAI4_SCK
_A
-
SAI4_CK2
-
FMC_A21
DCMI_
D6/PSSI
_D6
LCD_G
0
EVENT
OUT
PE6
TRACE
D3
TIM1_
BKIN2
SAI1_D1
-
TIM15_
CH2
SPI4_
MOSI
SAI1_SD_
A
-
SAI4_SD_
A
SAI4_D1
SAI4_
MCLK_B
TIM1_BKIN
2_COMP12
FMC_A22
DCMI_
D7/PSSI
_D7
LCD_G
1
EVENT
OUT
PE7
-
TIM1_ET
R
-
DFSDM1
_DATIN2
-
-
-
UART7_
RX
-
-
OCTO
SPIM_P1_
IO4
-
FMC_D4/
FMC_AD4
-
-
EVENT
OUT
PE8
-
TIM1_CH
1N
-
DFSDM1
_CKIN2
-
-
-
UART7_
TX
-
-
OCTO
SPIM_P1_
IO5
-
FMC_D5/
FMC_AD5
COMP2_
OUT
-
EVENT
OUT
PE9
-
TIM1_CH
1
-
DFSDM1
_CKOUT
-
-
-
UART7_
RTS/
UART7_
DE
-
-
OCTO
SPIM_P1_
IO6
-
FMC_D6/
FMC_AD6
-
-
EVENT
OUT
Pinouts, pin descriptions and alternate functions
DS13314 Rev 3
Port E
AF1
STM32H733xG
Table 8. STM32H733 pin alternate functions (continued)
AF0
Port
DS13314 Rev 3
Port E
SYS
AF1
AF2
AF3
AF4
AF5
AF6
AF7
AF8
AF9
AF10
AF11
CEC/
DCMI/
CRS/
DFSDM1/
FDCAN1/2
DFSDM1
PSSI/
DFSDM1/I SDMMC1
FMC/
ETH/I2C4/
CEC/
LPUART1/
/FMC/
/LCD/
DFSDM1
2C4/5/
/SPI2/I2S
LCD/
LCD/MDIO
FMC/
FDCAN3/
FDCAN3/
SAI4/
LCD/
LPTIM2/ /I2C1/2/3/
OCTO
2/SPI3/
OCTO
S/OCTOSP
LPTIM1/
PDM_
SPI1/I2S
SDMMC1/
OCTO
3/4/5/
4/5/
SPIM_P1/
I2S3/
SPIM_P1/
IM_P1/
SAI4/TIM1
SAI1/
1/SPI2/
SPDIFRX1 SPIM_P1/
LPUART LPTIM2/
SAI1/
SPI6/
OTG1_FS/ SDMMC2/
6/17/TIM1 TIM3/4/5/1
I2S2/SPI
/SPI6/
2/SAI4/
1/OCTO
OCTO
SPI3/
UART7/
OTG1_HS/ SWPMI1/
x/TIM2x
2/15
3/I2S3/
UART4/5/ SDMMC2/
SPIM_P1 SPIM_P1
I2S3/
USART1/
SAI4/
TIM1x/TIM
SPI4/5/6
8
SPDIFRX1
/2/TIM8
/TIM15/
UART4
2/3/6
SDMMC2/ 8/UART7/9/
/TIM13/14
USART1/
TIM8
USART10
10
AF12
AF13
AF14
AF15
FMC/LCD/
MDIOS/
OCTOSPI
M_P1/
SDMMC1/
TIM1x/
TIM8
COMP/
DCMI/
PSSI/
LCD/
TIM1x/
TIM23
LCD/
TIM24/
UART5
SYS
PE10
-
TIM1_CH
2N
-
DFSDM1
_DATIN4
-
-
-
UART7_
CTS
-
-
OCTO
SPIM_P1_
IO7
-
FMC_D7/
FMC_AD7
-
-
EVENT
OUT
PE11
-
TIM1_CH
2
-
DFSDM1
_CKIN4
-
SPI4_
NSS
-
-
-
-
SAI4_SD_
B
OCTO
SPIM_P1_
NCS
FMC_D8/
FMC_AD8
-
LCD_G
3
EVENT
OUT
PE12
-
TIM1_CH
3N
-
DFSDM1
_DATIN5
-
SPI4_
SCK
-
-
-
-
SAI4_SCK
_B
-
FMC_D9/
FMC_AD9
COMP1_
OUT
LCD_B
4
EVENT
OUT
PE13
-
TIM1_CH
3
-
DFSDM1
_CKIN5
-
SPI4_
MISO
-
-
-
-
SAI4_FS_
B
-
FMC_D10/
FMC_
AD10
COMP2_
OUT
LCD_
DE
EVENT
OUT
PE14
-
TIM1_CH
4
-
-
-
SPI4_
MOSI
-
-
-
-
SAI4_
MCLK_B
-
FMC_D11/
FMC_
AD11
-
LCD_
CLK
EVENT
OUT
PE15
-
TIM1_
BKIN
-
-
-
-
-
-
-
-
-
USART10_
CK
FMC_D12/
FMC_
AD12
TIM1_
BKIN_
COMP12
LCD_
R7
EVENT
OUT
Pinouts, pin descriptions and alternate functions
82/236
Table 8. STM32H733 pin alternate functions (continued)
STM32H733xG
AF0
Port
SYS
AF2
AF3
AF4
AF5
AF6
AF7
AF8
AF9
AF10
AF11
CEC/
DCMI/
CRS/
DFSDM1/
FDCAN1/2
DFSDM1
PSSI/
DFSDM1/I SDMMC1
FMC/
ETH/I2C4/
CEC/
LPUART1/
/FMC/
/LCD/
DFSDM1
2C4/5/
/SPI2/I2S
LCD/
LCD/MDIO
FMC/
FDCAN3/
FDCAN3/
SAI4/
LCD/
LPTIM2/ /I2C1/2/3/
OCTO
2/SPI3/
OCTO
S/OCTOSP
LPTIM1/
PDM_
SPI1/I2S
SDMMC1/
OCTO
3/4/5/
4/5/
SPIM_P1/
I2S3/
SPIM_P1/
IM_P1/
SAI4/TIM1
SAI1/
1/SPI2/
SPDIFRX1 SPIM_P1/
LPUART LPTIM2/
SAI1/
SPI6/
OTG1_FS/ SDMMC2/
6/17/TIM1 TIM3/4/5/1
I2S2/SPI
/SPI6/
2/SAI4/
1/OCTO
OCTO
SPI3/
UART7/
OTG1_HS/ SWPMI1/
x/TIM2x
2/15
3/I2S3/
UART4/5/ SDMMC2/
SPIM_P1 SPIM_P1
I2S3/
USART1/
SAI4/
TIM1x/TIM
SPI4/5/6
8
SPDIFRX1
/2/TIM8
/TIM15/
UART4
2/3/6
SDMMC2/ 8/UART7/9/
/TIM13/14
USART1/
TIM8
USART10
10
AF12
AF13
AF14
AF15
FMC/LCD/
MDIOS/
OCTOSPI
M_P1/
SDMMC1/
TIM1x/
TIM8
COMP/
DCMI/
PSSI/
LCD/
TIM1x/
TIM23
LCD/
TIM24/
UART5
SYS
83/236
PF0
-
-
-
-
I2C2_
SDA
-
I2C5_SDA
-
-
OCTO
SPIM_P2_
IO0
-
-
FMC_A0
TIM23_
CH1
-
EVENT
OUT
PF1
-
-
-
-
I2C2_
SCL
-
I2C5_SCL
-
-
OCTO
SPIM_P2_
IO1
-
-
FMC_A1
TIM23_
CH2
-
EVENT
OUT
PF2
-
-
-
-
I2C2_
SMBA
-
I2C5_
SMBA
-
-
OCTO
SPIM_P2_
IO2
-
-
FMC_A2
TIM23_
CH3
-
EVENT
OUT
PF3
-
-
-
-
-
-
-
-
-
OCTO
SPIM_P2_
IO3
-
-
FMC_A3
TIM23_
CH4
-
EVENT
OUT
PF4
-
-
-
-
-
-
-
-
-
OCTO
SPIM_P2_
CLK
-
-
FMC_A4
-
-
EVENT
OUT
PF5
-
-
-
-
-
-
-
-
-
OCTO
SPIM_P2_
NCLK
-
-
FMC_A5
-
-
EVENT
OUT
PF6
-
TIM16_
CH1
FDCAN3_
RX
-
-
SPI5_
NSS
SAI1_SD_
B
UART7_
RX
SAI4_SD_
B
-
OCTO
SPIM_P1_
IO3
-
-
TIM23_
CH1
-
EVENT
OUT
PF7
-
TIM17_
CH1
FDCAN3_
TX
-
-
SPI5_
SCK
SAI1_
MCLK_B
UART7_
TX
SAI4_
MCLK_B
-
OCTO
SPIM_P1_
IO2
-
-
TIM23_
CH2
-
EVENT
OUT
PF8
-
TIM16_
CH1N
-
-
-
SPI5_
MISO
SAI1_SCK
_B
UART7_
RTS/
UART7_
DE
SAI4_SCK TIM13_CH
_B
1
OCTO
SPIM_P1_
IO0
-
-
TIM23_
CH3
-
EVENT
OUT
PF9
-
TIM17_
CH1N
-
-
-
SPI5_
MOSI
SAI1_FS_
B
UART7_
CTS
SAI4_FS_
B
OCTO
SPIM_P1_
IO1
-
-
TIM23_
CH4
-
EVENT
OUT
TIM14_CH
1
Pinouts, pin descriptions and alternate functions
DS13314 Rev 3
Port F
AF1
STM32H733xG
Table 8. STM32H733 pin alternate functions (continued)
AF0
Port
DS13314 Rev 3
Port F
SYS
AF1
AF2
AF3
AF4
AF5
AF6
AF7
AF8
AF9
AF10
AF11
CEC/
DCMI/
CRS/
DFSDM1/
FDCAN1/2
DFSDM1
PSSI/
DFSDM1/I SDMMC1
FMC/
ETH/I2C4/
CEC/
LPUART1/
/FMC/
/LCD/
DFSDM1
2C4/5/
/SPI2/I2S
LCD/
LCD/MDIO
FMC/
FDCAN3/
FDCAN3/
SAI4/
LCD/
LPTIM2/ /I2C1/2/3/
OCTO
2/SPI3/
OCTO
S/OCTOSP
LPTIM1/
PDM_
SPI1/I2S
SDMMC1/
OCTO
3/4/5/
4/5/
SPIM_P1/
I2S3/
SPIM_P1/
IM_P1/
SAI4/TIM1
SAI1/
1/SPI2/
SPDIFRX1 SPIM_P1/
LPUART LPTIM2/
SAI1/
SPI6/
OTG1_FS/ SDMMC2/
6/17/TIM1 TIM3/4/5/1
I2S2/SPI
/SPI6/
2/SAI4/
1/OCTO
OCTO
SPI3/
UART7/
OTG1_HS/ SWPMI1/
x/TIM2x
2/15
3/I2S3/
UART4/5/ SDMMC2/
SPIM_P1 SPIM_P1
I2S3/
USART1/
SAI4/
TIM1x/TIM
SPI4/5/6
8
SPDIFRX1
/2/TIM8
/TIM15/
UART4
2/3/6
SDMMC2/ 8/UART7/9/
/TIM13/14
USART1/
TIM8
USART10
10
AF12
AF13
AF14
AF15
FMC/LCD/
MDIOS/
OCTOSPI
M_P1/
SDMMC1/
TIM1x/
TIM8
COMP/
DCMI/
PSSI/
LCD/
TIM1x/
TIM23
LCD/
TIM24/
UART5
SYS
PF10
-
TIM16_BK
IN
SAI1_D3
-
PSSI_
D15
-
-
-
-
OCTO
SPIM_P1_
CLK
SAI4_D3
-
-
DCMI_
D11/PSSI
_D11
LCD_D
E
EVENT
OUT
PF11
-
-
-
-
-
SPI5_
MOSI
-
-
-
OCTO
SPIM_P1_
NCLK
SAI4_SD_
B
-
FMC_
NRAS
DCMI_
D12/PSS
I_D12
TIM24_
CH1
EVENT
OUT
PF12
-
-
-
-
-
-
-
-
-
OCTO
SPIM_P2_
DQS
-
-
FMC_A6
-
TIM24_
CH2
EVENT
OUT
PF13
-
-
-
DFSDM1
_DATIN6
I2C4_
SMBA
-
-
-
-
-
-
-
FMC_A7
-
TIM24_
CH3
EVENT
OUT
PF14
-
-
-
DFSDM1
_CKIN6
I2C4_
SCL
-
-
-
-
-
-
-
FMC_A8
-
TIM24_
CH4
EVENT
OUT
PF15
-
-
-
-
I2C4_
SDA
-
-
-
-
-
-
-
FMC_A9
-
-
EVENT
OUT
Pinouts, pin descriptions and alternate functions
84/236
Table 8. STM32H733 pin alternate functions (continued)
STM32H733xG
AF0
Port
SYS
AF2
AF3
AF4
AF5
AF6
AF7
AF8
AF9
AF10
AF11
CEC/
DCMI/
CRS/
DFSDM1/
FDCAN1/2
DFSDM1
PSSI/
DFSDM1/I SDMMC1
FMC/
ETH/I2C4/
CEC/
LPUART1/
/FMC/
/LCD/
DFSDM1
2C4/5/
/SPI2/I2S
LCD/
LCD/MDIO
FMC/
FDCAN3/
FDCAN3/
SAI4/
LCD/
LPTIM2/ /I2C1/2/3/
OCTO
2/SPI3/
OCTO
S/OCTOSP
LPTIM1/
PDM_
SPI1/I2S
SDMMC1/
OCTO
3/4/5/
4/5/
SPIM_P1/
I2S3/
SPIM_P1/
IM_P1/
SAI4/TIM1
SAI1/
1/SPI2/
SPDIFRX1 SPIM_P1/
LPUART LPTIM2/
SAI1/
SPI6/
OTG1_FS/ SDMMC2/
6/17/TIM1 TIM3/4/5/1
I2S2/SPI
/SPI6/
2/SAI4/
1/OCTO
OCTO
SPI3/
UART7/
OTG1_HS/ SWPMI1/
x/TIM2x
2/15
3/I2S3/
UART4/5/ SDMMC2/
SPIM_P1 SPIM_P1
I2S3/
USART1/
SAI4/
TIM1x/TIM
SPI4/5/6
8
SPDIFRX1
/2/TIM8
/TIM15/
UART4
2/3/6
SDMMC2/ 8/UART7/9/
/TIM13/14
USART1/
TIM8
USART10
10
AF12
AF13
AF14
AF15
FMC/LCD/
MDIOS/
OCTOSPI
M_P1/
SDMMC1/
TIM1x/
TIM8
COMP/
DCMI/
PSSI/
LCD/
TIM1x/
TIM23
LCD/
TIM24/
UART5
SYS
85/236
PG0
-
-
-
-
-
-
-
-
-
OCTO
SPIM_P2_
IO4
-
UART9_RX
FMC_A10
-
-
EVENT
OUT
PG1
-
-
-
-
-
-
-
-
-
OCTO
SPIM_P2_
IO5
-
UART9_TX
FMC_A11
-
-
EVENT
OUT
PG2
-
-
-
TIM8_
BKIN
-
-
-
-
-
-
-
TIM8_BKIN
_COMP12
FMC_A12
-
TIM24_
ETR
EVENT
OUT
PG3
-
-
-
TIM8_
BKIN2
-
-
-
-
-
-
-
TIM8_
BKIN2_
COMP12
FMC_A13
TIM23_
ETR
-
EVENT
OUT
PG4
-
TIM1_BKI
N2
-
-
-
-
-
-
-
-
-
TIM1_
BKIN2_
COMP12
FMC_A14/
FMC_BA0
-
-
EVENT
OUT
PG5
-
TIM1_
ETR
-
-
-
-
-
-
-
-
-
-
FMC_A15/
FMC_BA1
-
-
EVENT
OUT
PG6
-
TIM17_
BKIN
-
-
-
-
-
-
-
-
OCTO
SPIM_P1_
NCS
-
FMC_NE3
DCMI_D
12/PSSI_
D12
LCD_R
7
EVENT
OUT
PG7
-
-
-
-
-
-
SAI1_
MCLK_A
USART6
_CK
-
OCTO
SPIM_P2_
DQS
-
-
FMC_INT
DCMI_D
13/PSSI_
D13
LCD_
CLK
EVENT
OUT
PG8
-
-
-
TIM8_
ETR
-
SPI6_
NSS/I2S
6_WS
-
USART6
_RTS/
USART6
_DE
SPDIFRX1
_IN3
-
-
ETH_PPS_
OUT
FMC_
SDCLK
-
LCD_G
7
EVENT
OUT
PG9
-
-
FDCAN3_
TX
-
-
SPI1_
MISO/I2S
1_SDI
-
USART6
_RX
OCTO
SPDIFRX1
SPIM_P1_
_IN4
IO6
SAI4_FS_
B
SDMMC2_
D0
FMC_NE2/
FMC_NCE
DCMI_
VSYNC/
PSSI_
RDY
-
EVENT
OUT
Pinouts, pin descriptions and alternate functions
DS13314 Rev 3
Port G
AF1
STM32H733xG
Table 8. STM32H733 pin alternate functions (continued)
AF0
Port
SYS
AF2
AF3
AF4
AF5
AF6
AF7
AF8
AF9
AF10
AF11
CEC/
DCMI/
CRS/
DFSDM1/
FDCAN1/2
DFSDM1
PSSI/
DFSDM1/I SDMMC1
FMC/
ETH/I2C4/
CEC/
LPUART1/
/FMC/
/LCD/
DFSDM1
2C4/5/
/SPI2/I2S
LCD/
LCD/MDIO
FMC/
FDCAN3/
FDCAN3/
SAI4/
LCD/
LPTIM2/ /I2C1/2/3/
OCTO
2/SPI3/
OCTO
S/OCTOSP
LPTIM1/
PDM_
SPI1/I2S
SDMMC1/
OCTO
3/4/5/
4/5/
SPIM_P1/
I2S3/
SPIM_P1/
IM_P1/
SAI4/TIM1
SAI1/
1/SPI2/
SPDIFRX1 SPIM_P1/
LPUART LPTIM2/
SAI1/
SPI6/
OTG1_FS/ SDMMC2/
6/17/TIM1 TIM3/4/5/1
I2S2/SPI
/SPI6/
2/SAI4/
1/OCTO
OCTO
SPI3/
UART7/
OTG1_HS/ SWPMI1/
x/TIM2x
2/15
3/I2S3/
UART4/5/ SDMMC2/
SPIM_P1 SPIM_P1
I2S3/
USART1/
SAI4/
TIM1x/TIM
SPI4/5/6
8
SPDIFRX1
/2/TIM8
/TIM15/
UART4
2/3/6
SDMMC2/ 8/UART7/9/
/TIM13/14
USART1/
TIM8
USART10
10
AF12
AF13
AF14
AF15
FMC/LCD/
MDIOS/
OCTOSPI
M_P1/
SDMMC1/
TIM1x/
TIM8
COMP/
DCMI/
PSSI/
LCD/
TIM1x/
TIM23
LCD/
TIM24/
UART5
SYS
SDMMC2_
D1
FMC_NE3
DCMI_
D2/PSSI
_D2
LCD_B
2
EVENT
OUT
OCTO
SPDIFRX1
SPIM_P2_
_IN1
IO7
SDMMC2_
D2
ETH_MII_
TX_EN/
ETH_RMII_
TX_EN
-
DCMI_
D3/PSSI
_D3
LCD_B
3
EVENT
OUT
USART6
_RTS/
USART6
_DE
SPDIFRX1
_IN2
LCD_B4
SDMMC2_
D3
ETH_MII_
TXD1/ETH
_RMII_TXD
1
FMC_NE4
TIM23_
CH1
LCD_B
1
EVENT
OUT
-
USART6
_CTS/
USART6
_NSS
-
-
SDMMC2_
D6
ETH_MII_
TXD0/ETH
_RMII_TXD
0
FMC_A24
TIM23_
CH2
LCD_R
0
EVENT
OUT
SPI6_
MOSI/I2S
6_SDO
-
USART6
_TX
-
OCTO
SPIM_P1_
IO7
SDMMC2_
D7
ETH_MII_
TXD1/ETH
_RMII_TXD
1
FMC_A25
TIM23_
CH3
LCD_B
0
EVENT
OUT
-
-
-
USART6
_CTS/
USART6
_NSS
-
OCTO
SPIM_P2_
DQS
-
USART10_
CK
FMC_NCA
S
DCMI_D
13/PSSI_
D13
-
EVENT
OUT
-
-
-
-
-
-
-
-
-
-
-
-
EVENT
OUT
-
-
-
-
-
-
-
-
-
-
-
-
EVENT
OUT
-
-
FDCAN3_
RX
OCTO
SPIM_P2
_IO6
-
SPI1_
NSS/I2S
1_WS
-
-
PG11
-
LPTIM1_
IN2
-
-
USART1
0_RX
SPI1_
SCK/I2S
1_CK
-
-
PG12
-
LPTIM1_
IN1
-
OCTO
SPIM_P2
_NCS
USART1
0_TX
SPI6_
MISO/I2S
6_SDI
-
PG13
TRACE
D0
LPTIM1_
OUT
-
-
USART1
0_CTS/
USART1
0_NSS
SPI6_
SCK/I2S
6_CK
PG14
TRACE
D1
LPTIM1_
ETR
-
-
USART1
0_RTS/
USART1
0_DE
PG15
-
-
-
-
PH0
-
-
-
PH1
-
-
-
-
LCD_G3
STM32H733xG
SAI4_SD_
B
PG10
Port G
DS13314 Rev 3
Port H
AF1
Pinouts, pin descriptions and alternate functions
86/236
Table 8. STM32H733 pin alternate functions (continued)
STM32H733xG
6
6.1
Electrical characteristics
Electrical characteristics
Parameter conditions
Unless otherwise specified, all voltages are referenced to VSS.
6.1.1
Minimum and maximum values
Unless otherwise specified the minimum and maximum values are guaranteed in the worst
conditions of junction temperature, supply voltage and frequencies by tests in production on
100% of the devices with an junction temperature at TJ = 25 °C and TJ = TJmax (given by the
selected temperature range).
Data based on characterization results, design simulation and/or technology characteristics
are indicated in the table footnotes. Based on characterization, the minimum and maximum
values refer to sample tests and represent the mean value plus or minus three times the
standard deviation (mean±3σ).
6.1.2
Typical values
Unless otherwise specified, typical data are based on TJ = 25 °C, VDD = 3.3 V (for the
1.7 V ≤ VDD ≤ 3.6 V voltage range). They are given only as design guidelines and are not
tested.
Typical ADC accuracy values are determined by characterization of a batch of samples from
a standard diffusion lot over the full temperature range, where 95% of the devices have an
error less than or equal to the value indicated (mean±2σ).
6.1.3
Typical curves
Unless otherwise specified, all typical curves are given only as design guidelines and are
not tested.
6.1.4
Loading capacitor
The loading conditions used for pin parameter measurement are shown in Figure 8.
6.1.5
Pin input voltage
The input voltage measurement on a pin of the device is described in Figure 9.
Figure 8. Pin loading conditions
Figure 9. Pin input voltage
MCU pin
MCU pin
C = 50 pF
VIN
MS19011V2
DS13314 Rev 3
MS19010V2
87/236
216
Electrical characteristics
6.1.6
STM32H733xG
Power supply scheme
Figure 10. Power supply scheme
VCAP
Level shifter
IOs
D3 domain
(System
logic,
EXTI,
IO
logic Peripherals,
RAM)
Power
switch
VSS
Power
switch
Core domain (VCORE)
LDO
voltage
regulator
VDDLDO
D2 domain
(peripherals,
RAM)
D1 domain
(CPU, peripherals,
RAM)
Flash
VSS
VDD domain
VDD
VBAT
charging
LSI, HSI,
CSI, HSI48,
HSE, PLLs
Backup domain
Backup VBKP
regulator
VSW
VBAT
Power
switch
Power switch
LSE, RTC,
Wakeup logic,
backup
IO
logic registers, Reset
BKUP
IOs
VSS
Backup
RAM
VSS
VDD33USB
USB
FS IOs
VDDA
Analog domain
REF_BUF
VREF+
ADC, DAC
VREF+
VREF-
VREF-
OPAMP,
Comparator
VSSA
MSv65399V2
1. Refer to application note AN5419 “Getting started with STM32H723/733, STM32H725/735 and
STM32H730 Value Line hardware development“ for the possible power scheme and connected capacitors.
88/236
DS13314 Rev 3
STM32H733xG
6.1.7
Electrical characteristics
Current consumption measurement
Figure 11. Current consumption measurement scheme
LDO ON
IDD_VBAT
VBAT
IDD
VDD
VDDLDO
VDDA
6.2
Absolute maximum ratings
Stresses above the absolute maximum ratings listed in Table 9: Voltage characteristics,
Table 10: Current characteristics, and Table 11: Thermal characteristics may cause
permanent damage to the device. These are stress ratings only and the functional operation
of the device at these conditions is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability. Device mission profile (application conditions)
is compliant with JEDEC JESD47 Qualification Standard, extended mission profiles are
available on demand.
Table 9. Voltage characteristics
Symbols
Ratings
Min
Max
Unit
VDDX - VSS(1)
External main supply voltage (including VDD,
VDDLDO, VDDA, VDD33USB, VBAT)
−0.3
4.0
V
Input voltage on FT_xxx pins
VSS−0.3
Min(VDD, VDDA,
VDD33USB, VBAT)
+4.0(3)(4)
V
Input voltage on TT_xx pins
VSS−0.3
4.0
V
Input voltage on BOOT0 pin
VSS
9.0
V
VSS-0.3
4.0
V
Variations between different VDDX power
pins of the same domain
-
50
mV
Variations between all the different ground
pins
-
50
mV
VIN(2)
Input voltage on any other pins
|∆VDDX|
|VSSx-VSS|
1. All main power (VDD, VDDA, VDD33USB, VBAT) and ground (VSS, VSSA) pins must always be connected to
the external power supply, in the permitted range.
2. VIN maximum must always be respected.
3. This formula has to be applied on power supplies related to the IO structure described by the pin definition
table.
DS13314 Rev 3
89/236
216
Electrical characteristics
STM32H733xG
4. To sustain a voltage higher than 4V the internal pull-up/pull-down resistors must be disabled.
Table 10. Current characteristics
Symbols
Ratings
Max
ΣIVDD
(1)
Total current into sum of all VDD power lines (source)
620
ΣIVSS
Total current out of sum of all VSS ground lines (sink)(1)
620
IVDD
IVSS
IIO
ΣI(PIN)
IINJ(PIN)
(3)(4)
ΣIINJ(PIN)
Maximum current into each VDD power pin
(source)(1)
100
(1)
100
Maximum current out of each VSS ground pin (sink)
Output current sunk by any I/O and control pin, except Px_C
20
Output current sunk by Px_C pins
1
Total output current sunk by sum of all I/Os and control
pins(2)
Unit
mA
140
Total output current sourced by sum of all I/Os and control pins(2)
140
Injected current on FT_xxx, TT_xx, RST and B pins except PA4,
PA5
−5/+0
Injected current on PA4, PA5
−0/0
Total injected current (sum of all I/Os and control pins)(5)
±25
1. All main power (VDD, VDDA, VDD33USB) and ground (VSS, VSSA) pins must always be connected to the
external power supplies, in the permitted range.
2. This current consumption must be correctly distributed over all I/Os and control pins. The total output
current must not be sunk/sourced between two consecutive power supply pins referring to high pin count
QFP packages.
3. Positive injection is not possible on these I/Os and does not occur for input voltages lower than the
specified maximum value.
4. A positive injection is induced by VIN>VDD while a negative injection is induced by VIN<VSS. IINJ(PIN) must
never be exceeded. Refer also to Table 9: Voltage characteristics for the maximum allowed input voltage
values.
5. When several inputs are submitted to a current injection, the maximum ∑IINJ(PIN) is the absolute sum of the
positive and negative injected currents (instantaneous values).
Table 11. Thermal characteristics
Symbol
TSTG
TJ
90/236
Ratings
Storage temperature range
Maximum junction
temperature
Industrial temperature range 6
DS13314 Rev 3
Value
Unit
− 65 to +150
°C
125
STM32H733xG
Electrical characteristics
6.3
Operating conditions
6.3.1
General operating conditions
Table 12. General operating conditions
Symbol
Parameter
Operating
conditions
Min
Typ
Max
VDD
Standard operating voltage
-
1.62(1)
-
3.6
VDDLDO
Supply voltage for the internal
regulator
1.62(1)
-
3.6
VDD33USB
Standard operating voltage, USB
domain
3.0
-
3.6
0
-
3.6
ADC or COMP used
1.62
-
DAC used
1.8
-
OPAMP used
2.0
-
VREFBUF used
1.8
-
ADC, DAC, OPAMP,
COMP, VREFBUF not
used
0
-
-
1.2(2)
-
3.6
−0.3
-
VDD+0.3
0
-
9
VDDA
VBAT
Analog operating voltage
VDDLDO ≤ VDD
USB used
USB not used
Supply voltage for Backup domain
TT_xx I/O
BOOT0
VIN
VCORE
Regulator OFF: external VCORE
voltage must be supplied from
external regulator on VCAP pins
3.6
V
All I/O except BOOT0
and TT_xx
−0.3
-
Min(VDD,
VDDA,
VDD33USB)
+3.6V <
5.5V(3)
VOS3
0.95
1.0
1.05
VOS2
1.05
1.10
1.15
VOS1
1.15
1.21
1.26
VOS0
1.30
1.36
1.40
VOS3
0.98
1.03
1.08
VOS2
1.08
1.13
1.18
VOS1
1.18
1.23
1.28
VOS0
1.33
1.38
1.40
I/O Input voltage
Internal regulator ON (LDO)(4)
DS13314 Rev 3
Unit
V
91/236
216
Electrical characteristics
STM32H733xG
Table 12. General operating conditions (continued)
Symbol
fCPU
fACLK
fHCLK
fPCLK
Parameter
Arm® Cortex®-M7 clock frequency
AXI clock frequency
AHB clock frequency
APB clock frequency
Ambient temperature for
temperature range 3
TA(6)
Ambient temperature for
temperature range 6
Operating
conditions
Min
Typ
Max
VOS3
-
-
170
VOS2
-
-
300
VOS1
-
-
400
VOS0
-
-
520
VOS0 and
CPU_FREQ_BOOST
-
-
550
VOS3
-
-
85
VOS2
-
-
150
VOS1
-
-
200
VOS0
-
-
275
VOS3
-
-
85
VOS2
-
-
150
VOS1
-
-
200
VOS0
-
-
275
VOS3
-
-
42.5(5)
VOS2
-
-
75
VOS1
-
-
100
VOS0
-
-
137.5
Maximum power
dissipation
−40
125
Maximum power
dissipation
−40
85
Low-power
dissipation(7)
−40
105
Unit
MHz
°C
1. When RESET is released, the functionality is guaranteed down to VPDRmax or down to the specified VDDmin when the PDR
is OFF. The PDR can only be switched OFF though the PDR_ON pin that not available in all packages.
2. VBAT minimum value can be reduced to 0 V if VDD is present.
3. This formula has to be applied on power supplies related to the I/O structure described by the pin definition table.
4. At startup, the external VCORE voltage must remain higher or equal to 1.10 V before disabling the internal regulator (LDO).
5. This value corresponds to the maximum APB clock frequency when at least one peripheral is enabled.
6. The device junction temperature must be kept below maximum TJ indicated in Table 13: Supply voltage and maximum
temperature configuration and the maximum temperature.
7. In low-power dissipation state, TA can be extended to this range as long as TJ does not exceed TJmax (see Section 7.5:
Thermal characteristics).
92/236
DS13314 Rev 3
STM32H733xG
Electrical characteristics
Table 13. Supply voltage and maximum temperature configuration
Power scale
VOS0
VOS1
VOS2 or VOS3
SVOS4/SVOS5
VCORE source
Max. TJ (°C)
LDO
Min. VDDLDO (V)
1.7
1.7
1.62
-
1.62
1.62
-
-
1.62
1.62
-
-
125
2
2
105
1.62
1.62
125
1.62
-
105
External (Bypass)
LDO
125
External (Bypass)
LDO
125
External (bypass)
LDO
External (Bypass)
6.3.2
Min. VDD(V)
VCAP external capacitor
Stabilization for the main regulator is achieved by connecting an external capacitor CEXT to
the VCAP pin. CEXT is specified in Table 14. Two external capacitors can be connected to
VCAP pins.
Figure 12. External capacitor CEXT
C
ESR
R Leak
MS19044V2
1. Legend: ESR is the equivalent series resistance.
Table 14. VCAP operating conditions(1)
Symbol
Parameter
Conditions
CEXT
Capacitance of external capacitor
2.2 µF(2)(3)
ESR
ESR of external capacitor
< 100 mΩ
1. When bypassing the voltage regulator, the two 2.2 µF VCAP capacitors are not required and should be
replaced by two 100 nF decoupling capacitors.
2. This value corresponds to CEXT typical value. A variation of +/-20% is tolerated.
3.
If a third VCAP pin is available on the package, it must be connected to the other VCAP pins but no
additional capacitor is required.
DS13314 Rev 3
93/236
216
Electrical characteristics
6.3.3
STM32H733xG
Operating conditions at power-up / power-down
Subject to general operating conditions for TA.
Table 15. Operating conditions at power-up/power-down
Symbol
tVDD
tVDDA
tVDDUSB
tVCORE(1)
Parameter
Min
Max
VDD rise time rate
0
∞
VDD fall time rate
10
∞
VDDA rise time rate
0
∞
VDDA fall time rate
10
∞
VDDUSB rise time rate
0
∞
VDDUSB fall time rate
10
∞
0
285
10
∞
VCORE rise time
rate(2)
VCORE fall time rate
Unit
µs/V
1. tVCORE should be achieved when VCORE is provided by an external supply voltage (bypass with
VDDLDO = VCORE).
2. VCORE rising slope must respect the above constraints. There are no constraints on the delay between VDD
rising and VCORE rising,
94/236
DS13314 Rev 3
STM32H733xG
6.3.4
Electrical characteristics
Embedded reset and power control block characteristics
The parameters given in Table 16 are derived from tests performed under ambient
temperature and VDD supply voltage conditions summarized in Table 12: General operating
conditions.
Table 16. Reset and power control block characteristics
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
tRSTTEMPO(1)
Reset temporization
after BOR0 released
-
-
377
550
µs
VPOR/PDR
Power-on/power-down reset
threshold
Rising edge(1)
1.62
1.67
1.71
Falling edge
1.58
1.62
1.68
VBOR1
Brown-out reset threshold 1
2.04
2.10
2.15
1.95
2.00
2.06
VBOR2
Brown-out reset threshold 2
2.34
2.41
2.47
2.25
2.31
2.37
VBOR3
Brown-out reset threshold 3
2.63
2.70
2.78
2.54
2.61
2.68
VPVD0
Programmable Voltage
Detector threshold 0
Rising edge
1.90
1.96
2.01
1.81
1.86
1.91
VPVD1
Programmable Voltage
Detector threshold 1
Rising edge
2.05
2.10
2.16
1.96
2.01
2.06
VPVD2
Programmable Voltage
Detector threshold 2
Rising edge
2.19
2.26
2.32
2.10
2.15
2.21
VPVD3
Programmable Voltage
Detector threshold 3
Rising edge
2.35
2.41
2.47
2.25
2.31
2.37
VPVD4
Programmable Voltage
Detector threshold 4
Rising edge
2.49
2.56
2.62
2.39
2.45
2.51
VPVD5
Programmable Voltage
Detector threshold 5
Rising edge
2.64
2.71
2.78
2.55
2.61
2.68
VPVD6
Programmable Voltage
Detector threshold 6
Rising edge
2.78
2.86
2.94
2.69
2.76
2.83
VPOR/PDR
Hysteresis voltage for
Power-on/power-down reset
Hysteresis in Run mode
-
43.00
-
Vhyst_BOR_PVD
Hysteresis voltage for BOR
Hysteresis in Run mode
-
100
-
IDD_BOR_PVD(1)
BOR and PVD consumption
from VDD
-
-
-
0.630
IDD_POR_PVD
POR and PVD consumption
from VDD
-
0.8
-
1.200
Rising edge
Falling edge
Rising edge
Falling edge
Rising edge
Falling edge
Falling edge
Falling edge
Falling edge
Falling edge
Falling edge
Falling edge
Falling edge in Run mode
V
mV
µA
DS13314 Rev 3
95/236
216
Electrical characteristics
STM32H733xG
Table 16. Reset and power control block characteristics (continued)
Symbol
Parameter
Conditions
Min
Typ
Max
VAVM_0
Analog voltage detector for
VDDA threshold 0
Rising edge
1.66
1.71
1.76
1.56
1.61
1.66
VAVM_1
Analog voltage detector for
VDDA threshold 1
Rising edge
2.06
2.12
2.19
1.96
2.02
2.08
VAVM_2
Analog voltage detector for
VDDA threshold 2
Rising edge
2.42
2.50
2.58
2.35
2.42
2.49
VAVM_3
Analog voltage detector for
VDDA threshold 3
Rising edge
2.74
2.83
2.91
2.64
2.72
2.80
Vhyst_VDDA
Hysteresis of VDDA voltage
detector
-
-
100
-
mV
IDD_PVM
PVM consumption from
VDD(1)
-
-
-
0.25
µA
IDD_VDDA
Voltage detector
consumption on VDDA(1)
-
-
2.5
µA
Falling edge
Falling edge
Falling edge
Falling edge
Resistor bridge
Unit
V
1. Guaranteed by design.
6.3.5
Embedded reference voltage characteristics
The parameters given in Table 17 are derived from tests performed under ambient
temperature and VDD supply voltage conditions summarized in Table 12: General operating
conditions.
Table 17. Embedded reference voltage
Symbol
VREFINT
tS_vrefint(1)(2)
(3)
tS_vbat(2)
tstart_vrefint(2)
Irefbuf(2)
ΔVREFINT(2)
Tcoeff(2)
VDDcoeff(2)
96/236
Parameter
Conditions
Min
Typ
Max
Unit
-40°C < TJ < TJmax
1.180
1.216
1.255
V
ADC sampling time when
reading the internal reference
voltage
-
4.3
-
-
VBAT sampling time when
reading the internal VBAT
reference voltage
-
9
-
-
Start time of reference voltage
buffer when ADC is enable
-
-
-
4.4
VDD = 3.3 V
9
13.5
23
µA
-40°C < TJ < TJmax
-
5
15
mV
Average temperature
coefficient
-
20
70
ppm/°C
3.0 V < VDD < 3.6 V
-
10
1370
ppm/V
Internal reference voltages
Reference Buffer
consumption for ADC
Internal reference voltage
spread over the temperature
range
Average temperature
coefficient
Average Voltage coefficient
DS13314 Rev 3
µs
STM32H733xG
Electrical characteristics
Table 17. Embedded reference voltage (continued)
Symbol
Conditions
Min
Typ
Max
VREFINT_DIV1 1/4 reference voltage
-
-
25
-
VREFINT_DIV2 1/2 reference voltage
-
-
50
-
VREFINT_DIV3 3/4 reference voltage
-
-
75
-
1.
Parameter
Unit
%
VREFINT
The shortest sampling time for the application can be determined by multiple iterations.
2. Guaranteed by design.
3. Guaranteed by design. and tested in production at 3.3 V.
Table 18. Internal reference voltage calibration values
Symbol
Parameter
Raw data acquired at temperature of 30 °C, VDDA = 3.3 V
VREFIN_CAL
6.3.6
Memory address
1FF1 E860 - 1FF1 E861
Embedded USB regulator characteristics
The parameters given in Table 19 are derived from tests performed under ambient
temperature and VDD supply voltage conditions summarized in Table 12: General operating
conditions.
Table 19. USB regulator characteristics
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
VREGOUTV33V
Regulated output voltage
-
3
-
3.6
V
IOUT
Output current load sinked by
USB block
-
-
-
20
mA
TWKUP
Wakeup time
-
-
120
170
us
6.3.7
Supply current characteristics
The current consumption is a function of several parameters and factors such as the
operating voltage, ambient temperature, I/O pin loading, device software configuration,
operating frequencies, I/O pin switching rate, program location in memory and executed
binary code.
The current consumption is measured as described in Figure 11: Current consumption
measurement scheme.
All the run-mode current consumption measurements given in this section are performed
with a CoreMark code.
DS13314 Rev 3
97/236
216
Electrical characteristics
STM32H733xG
Typical and maximum current consumption
The MCU is placed under the following conditions:
•
All I/O pins are in analog input mode.
•
All peripherals are disabled except when explicitly mentioned.
•
The Flash memory access time is adjusted with the minimum wait states number,
depending on the fACLK frequency (refer to the table “Number of wait states according to
CPU clock (frcc_c_ck) frequency and VCORE range” available in the reference manual).
•
When the peripherals are enabled, the AHB clock frequency is the CPU frequency
divided by 2 and the APB clock frequency is AHB clock frequency divided by 2.
•
For typical values, the power supply is 3 V unless otherwise specified.
The parameters given in the below tables are derived from tests performed under ambient
temperature and supply voltage conditions summarized in Table 12: General operating
conditions.
98/236
DS13314 Rev 3
STM32H733xG
Electrical characteristics
Table 20. Typical and maximum current consumption in Run mode,
code with data processing running from ITCM(1)
Max(2)
Symbol
Parameter
Conditions
VOS0(3)
VOS0
VOS1
All
peripherals
disabled
VOS2
IDD
Supply
current in
Run mode
VOS3
VOS0
(3)
VOS0
All
peripherals
enabled
VOS1
VOS2
VOS3
frcc_c_ck
(MHz)
Typ
550
TJ =
25 °C
TJ =
85 °C
TJ =
105 °C
TJ =
125 °C
145
170
260
330
-
520
135
160
260
320
-
520
135
160
260
320
-
480
125
150
250
310
-
450
115
150
240
300
-
400
105
130
230
290
-
400
90.5
110
170
220
280
300
69.5
84
150
200
260
300
63
74
130
170
220
280
58
69
120
160
210
216
45.5
56
110
150
200
200
42
53
110
140
200
170
32.5
40
80
110
160
168
32
40
79
110
160
144
28
36
75
110
150
60
13.5
21
61
90
140
25
6.9
14
54
83
130
550
215
250
360
430
-
520
205
240
350
420
-
520
205
240
350
420
-
400
160
190
300
370
-
400
135
160
230
290
360
300
105
130
200
250
330
300
95
110
170
210
280
280
88
100
160
210
270
170
49
58
110
140
190
Unit
mA
1. Data are in DTCM for best computation performance, the cache has no influence on consumption in this case.
2. Guaranteed by characterization results, unless otherwise specified.
3. CPU_FREQ_BOOST is enabled.
DS13314 Rev 3
99/236
216
Electrical characteristics
STM32H733xG
Table 21. Typical and maximum current consumption in Run mode, code with data processing
running from Flash memory, cache ON(1)
Max(2)
Symbol
Parameter
Conditions
VOS0(3)
VOS0
VOS1
All
peripherals
disabled
IDD
Supply
current in Run
mode
VOS2
VOS3
VOS0
(3)
VOS0
All
peripherals
enabled
VOS1
VOS2
VOS3
frcc_c_ck
(MHz)
Typ
550
TJ =
25 °C
TJ =
85 °C
TJ =
105 °C
TJ =
125 °C
145
170
270
330
-
520
140
170
260
320
-
520
140
170
260
320
-
400
110
140
230
290
-
400
92
110
180
220
290
300
71
86
150
200
260
300
64
75
130
170
220
280
59
70
120
160
210
216
46.5
-
-
-
-
200
42.5
53
110
140
200
180
36
43
83
120
160
170
33.5
41
81
110
160
168
33
-
-
-
-
144
29
-
-
-
-
60
14
-
-
-
-
25
6.85
-
-
-
-
550
220
250
360
430
-
520
210
240
350
420
-
520
210
240
350
420
-
400
160
190
300
370
-
400
140
160
240
290
360
300
105
130
200
250
330
300
96
110
170
210
280
280
89
110
160
210
270
170
50
59
110
140
190
1. Data are in DTCM for best computation performance, the cache has no influence on consumption in this case.
2. Guaranteed by characterization results, unless otherwise specified.
3. CPU_FREQ_BOOST is enabled.
100/236
DS13314 Rev 3
Unit
mA
STM32H733xG
Electrical characteristics
Table 22. Typical and maximum current consumption in Run mode,
code with data processing running from Flash memory, cache OFF(1)
Symbol
Parameter
Conditions
VOS0(2)
VOS0
All peripherals
disabled
VOS1
VOS2
IDD
VOS3
Supply current
in Run mode
VOS0(2)
VOS0
All peripherals
enabled
VOS1
VOS2
VOS3
frcc_c_ck
(MHz)
Typ
550
99
520
95
520
95
400
76.5
400
66.5
300
51.5
300
47.5
280
43.5
170
24.5
550
170
520
165
520
165
400
130
400
115
300
87
300
79
280
73.5
170
41
Unit
mA
1. Data are in DTCM for best computation performance, the cache has no influence on consumption in this
case.
2. CPU_FREQ_BOOST is enabled.
DS13314 Rev 3
101/236
216
Electrical characteristics
STM32H733xG
Table 23. Typical consumption in Run mode and corresponding performance
versus code position
Conditions
Symbol
Coremark
Typ
ITCM
550
2777
145
52.2
FLASH
550
2777
145
52.2
AXI
SRAM
550
2777
145
52.2
SRAM 1
550
2777
150
54.0
SRAM 4
550
2777
145
FLASH
550
923
99
107.3
AXI
SRAM
550
1271
105
82.6
SRAM 1
550
790
96.5
122.2
SRAM 4
550
723
89.5
123.8
Peripheral
All
peripherals
disabled,
cache ON
Supply
current in
Run mode
IDD
All
peripherals
disabled
cache OFF
IDD/
Coremark
frcc_c_c k
(MHz)
Parameter
Code
Unit
Unit
µA/
Coremark
52.2
mA
Table 24. Typical current consumption in Autonomous mode
Symbol
IDD
Parameter
Supply current in
Autonous mode
Conditions
frcc_c_c k
(MHz)
Typ
Run, D1Stop,
D2Stop
VOS3
64
3.6
Run,
D1Standby,
D2Standby
VOS3
64
2.6
Unit
mA
Table 25. Typical and maximum current consumption in Sleep mode
Max(1)
Symbol
Parameter
Conditions
VOS0
(2)
VOS0
IDD(Sleep)
Supply
current in
Sleep mode
All
peripherals
disabled
VOS1
VOS2
VOS3
frcc_c_ck
(MHz)
Typ
550
TJ =
25 °C
TJ =
85 °C
36
-
-
-
-
520
33.5
60
170
240
-
520
33.5
60
170
240
-
400
27
52
160
230
-
400
22.5
39
110
170
240
300
18.5
34
110
160
240
300
16.5
28
85
130
190
170
9.7
21
78
120
190
170
8.5
17
61
96
150
1. Guaranteed by characterization results.
2. CPU_FREQ_BOOST is enabled.
102/236
DS13314 Rev 3
TJ =
TJ =
105 °C 125 °C
Unit
mA
STM32H733xG
Electrical characteristics
Table 26. Typical and maximum current consumption in Stop mode
Max(1)
Symbol
IDD(Stop)
Parameter
Supply
current in
Stop and
DStop
modes
Conditions
Flash memory in lowpower mode
Flash memory in
normal mode
Typ
TJ =
25 °C
TJ =
85 °C
TJ =
TJ =
105 °C 125 °C
SVOS5
0.52
3.7
26
44
72
SVOS4
0.81
6.1
39
64
110
SVOS3
1.15
8.6
51
82
130
SVOS5
0.535
3.7
26
44
72
SVOS4
0.96
6.2
39
64
110
SVOS3
1.45
8.8
51
83
130
Unit
mA
1. Guaranteed by characterization results.
Table 27. Typical and maximum current consumption in Standby mode
Typ(1)
Conditions
Symbol
IDD
(Standby)
Parameter
Max at 3.6 V(2)
Backup
SRAM
RTC
and
LSE(3)
1.65
V
2.4 V
3V
3.3 V
TJ =
25 °
C
TJ =
85 °
C
TJ =
105 °
C
TJ =
125 °
C
OFF
OFF
2.2
2.35
2.5
2.8
-
-
-
-
ON
OFF
3.5
3.7
4
4.3
-
-
-
-
OFF
ON
2.2
2.4
2.85
3.25
4.5
15
30
64
ON
ON
3.5
3.8
4.35
4.75
8.3
39
75
140
Supply
current in
Standby
mode,
IWDG OFF
Unit
µA
1. These values are given for PDR OFF. When the PDR is ON, the typical current consumption is increased
(refer to Table 16: Reset and power control block characteristics.
2. Guaranteed by characterization results.
3. The LSE is in Low-drive mode.
Table 28. Typical and maximum current consumption in VBAT mode
Conditions
Symbol
IDD
(VBAT)
Parameter
Supply
current in
VBAT
mode
Max at 3.6 V(1)(2)
Typ
TJ = TJ = Unit
TJ =
TJ =
105 ° 125 °
25 °C 85 °C
C
C
Back-up
SRAM
RTC
and
LSE(3)
1.2 V
2V
3V
3.3 V
OFF
OFF
0.008
0.01
0.025
0.05
0.3
3.1
7.4
18
ON
OFF
1.5
1.7
1.9
1.9
4
28
53
91
OFF
ON
0.4
0.5
0.75
0.8
-
-
-
-
ON
ON
1.8
2.1
2.8
3.2
-
-
-
-
µA
1. Guaranteed by characterization results.
2. The LDO regulator is used before switching to VBAT mode.
3. The LSE is in Low-drive mode.
I/O system current consumption
The current consumption of the I/O system has two components: static and dynamic.
DS13314 Rev 3
103/236
216
Electrical characteristics
STM32H733xG
I/O static current consumption
All the I/Os used as inputs with pull-up generate a current consumption when the pin is
externally held low. The value of this current consumption can be simply computed by using
the pull-up/pull-down resistors values given in Table 51: I/O static characteristics.
For the output pins, any external pull-down or external load must also be considered to
estimate the current consumption.
An additional I/O current consumption is due to I/Os configured as inputs if an intermediate
voltage level is externally applied. This current consumption is caused by the input Schmitt
trigger circuits used to discriminate the input value. Unless this specific configuration is
required by the application, this supply current consumption can be avoided by configuring
these I/Os in analog mode. This is notably the case of ADC input pins which should be
configured as analog inputs.
Caution:
Any floating input pin can also settle to an intermediate voltage level or switch inadvertently,
as a result of external electromagnetic noise. To avoid a current consumption related to
floating pins, they must either be configured in analog mode, or forced internally to a definite
digital value. This can be done either by using pull-up/down resistors or by configuring the
pins in output mode.
I/O dynamic current consumption
In addition to the internal peripheral current consumption (see Table 29: Peripheral current
consumption in Run mode), the I/Os used by an application also contribute to the current
consumption. When an I/O pin switches, it uses the current from the MCU supply voltage to
supply the I/O pin circuitry and to charge/discharge the capacitive load (internal or external)
connected to the pin:
I SW = V DDx × f SW × C L
where
ISW is the current sunk by a switching I/O to charge/discharge the capacitive load
VDDx is the MCU supply voltage
fSW is the I/O switching frequency
CL is the total capacitance seen by the I/O pin: C = CINT+ CEXT
The test pin is configured in push-pull output mode and is toggled by software at a fixed
frequency.
104/236
DS13314 Rev 3
STM32H733xG
Electrical characteristics
On-chip peripheral current consumption
The MCU is placed under the following conditions:
•
At startup, all I/O pins are in analog input configuration.
•
All peripherals are disabled unless otherwise mentioned.
•
The I/O compensation cell is enabled.
•
frcc_c_ck is the CPU clock. fPCLK = frcc_c_ck/4, and fHCLK = frcc_c_ck/2.
The given value is calculated by measuring the difference of current consumption
–
with all peripherals clocked off
–
with only one peripheral clocked on
–
frcc_c_ck = 550 MHz (Scale 0), frcc_c_ck = 400 MHz (Scale 1), frcc_c_ck = 300 MHz
(Scale 2), frcc_c_ck = 170 MHz (Scale 3)
•
The ambient operating temperature is 25 °C and VDD=3.3 V
•
The LDO regulator supplies VCORE.
Table 29. Peripheral current consumption in Run mode
IDD(Typ)
Peripheral
AHB3
Unit
VOS0
VOS1
VOS2
VOS3
MDMA
3.70
3.10
2.90
2.60
DMA2D
2.70
2.30
2.10
1.90
Flash memory
15.20
14.00
12.00
10.90
FMC registers
0.90
0.90
0.80
0.70
FMC kernel
7.00
6.10
5.60
5.40
OCTOSPI1 registers
1.40
1.30
0.50
0.40
OCTOSPI1 kernel
3.10
1.20
0.50
0.20
SDMMC1 registers
8.70
7.60
6.90
6.10
SDMMC1 kernel
2.10
1.80
1.40
1.20
OCTOSPI2 registers
1.40
1.30
0.90
0.60
OCTOSPI2 kernel
2.50
1.50
1.40
0.50
OTFDEC1
0.80
0.70
0.10
0.10
OTFDEC2
0.80
0.70
0.10
0.10
AXI SRAM
8.50
7.50
6.90
6.00
DS13314 Rev 3
µA/MHz
105/236
216
Electrical characteristics
STM32H733xG
Table 29. Peripheral current consumption in Run mode (continued)
IDD(Typ)
Peripheral
AHB1
AHB2
106/236
Unit
VOS0
VOS1
VOS2
VOS3
DMA1
0.70
0.60
0.50
0.40
DMA2
1.00
0.80
0.70
0.70
DMAMUX1
0.10
0.10
0.10
0.10
ADC1/2 registers
4.50
4.00
3.60
2.30
ADC1/2 kernel
0.90
0.80
0.60
0.40
USB1 registers
20.80
17.50
16.50
14.80
USB1 kernel
1.20
0.90
0.90
0.90
USB1 ULPI kernel
31.00
30.00
29.50
27.00
Ethernet
17.30
14.40
13.70
12.30
DCMI
4.80
4.00
3.80
3.40
CRYP
1.40
1.20
1.10
0.80
HASH1
1.70
1.40
1.30
1.00
HSEM
0.60
0.60
0.10
0.10
RNG1 registers
1.20
1.00
0.90
0.70
RNG1 kernel
15.00
13.60
10.00
9.00
SDMMC2 registers
15.00
12.20
11.70
10.40
SDMMC2 kernel
2.10
1.80
1.40
1.20
BDMA
6.50
5.90
4.80
4.30
SRAM1
2.40
2.00
1.80
1.60
SRAM2
2.70
2.30
2.00
1.80
CORDIC
0.80
0.60
0.50
0.50
FMAC
2.40
2.10
1.90
1.60
DS13314 Rev 3
µA/MHz
µA/MHz
STM32H733xG
Electrical characteristics
Table 29. Peripheral current consumption in Run mode (continued)
IDD(Typ)
Peripheral
AHB4
APB3
Unit
VOS0
VOS1
VOS2
VOS3
GPIOA
0.10
0.10
0.10
0.10
GPIOB
0.90
0.80
0.10
0.10
GPIOC
0.50
0.10
0.10
0.10
GPIOD
0.90
0.80
0.10
0.10
GPIOE
0.90
0.80
0.10
0.10
GPIOF
0.30
0.10
0.10
0.10
GPIOG
0.90
0.80
0.30
0.20
GPIOH
0.10
0.10
0.10
0.10
GPIOJ
0.90
0.80
0.30
0.20
GPIOK
0.80
0.80
0.10
0.10
HSEM
0.60
0.60
0.10
0.10
BDMA
6.50
5.90
4.80
4.30
CRC
0.90
0.30
0.30
0.30
ADC3 registers
2.10
1.40
1.30
1.20
ADC3 kernel
0.40
0.30
0.30
0.20
Backup SRAM
1.80
1.00
1.00
0.80
LTDC
9.00
7.90
7.70
6.40
WWDG1
0.60
0.50
0.50
0.50
DS13314 Rev 3
µA/MHz
107/236
216
Electrical characteristics
STM32H733xG
Table 29. Peripheral current consumption in Run mode (continued)
IDD(Typ)
Peripheral
APB1
108/236
Unit
VOS0
VOS1
VOS2
VOS3
TIM2
4.50
4.40
3.30
3.00
TIM3
3.80
3.20
2.90
2.70
TIM4
3.60
3.10
2.60
2.50
TIM5
4.10
3.40
3.10
2.90
TIM6
1.50
1.10
1.00
1.00
TIM7
1.40
1.10
0.90
0.90
TIM12
2.30
1.80
1.60
1.60
TIM13
1.90
1.40
1.30
1.20
TIM14
1.60
1.20
1.10
1.10
TIM23
4.60
3.90
3.60
3.40
TIM24
4.40
3.80
3.50
3.30
LPTIM1 registers
3.50
2.90
2.70
2.60
LPTIM1 kernel
2.60
2.30
2.00
1.80
SPI2 registers
2.10
1.60
0.90
0.80
SPI2 kernel
1.50
1.20
1.10
1.00
SPI3 registers
2.40
2.00
1.90
1.80
SPDIFRX registers
0.60
0.50
0.50
0.50
SPDIFRX kernel
3.50
2.80
2.40
2.20
USART2 registers
6.60
5.70
5.20
4.90
USART2 kernel
4.80
4.80
4.60
3.80
USART3 registers
5.90
5.40
4.60
4.30
USART3 kernel
4.00
3.40
3.00
2.90
UART4 registers
5.60
4.80
3.50
3.10
UART4 kernel
3.80
3.20
3.00
2.40
UART5 registers
5.60
4.60
4.40
4.00
UART5 kernel
3.90
3.40
3.30
3.20
UART7 registers
5.40
4.60
4.20
3.90
UART7 kernel
3.80
3.30
3.00
3.00
UART8 registers
5.60
4.10
3.50
3.40
UART8 kernel
3.60
3.20
3.20
3.10
I2C1 registers
0.90
0.60
0.60
0.50
I2C1 kernel
2.30
2.00
1.80
1.60
I2C2 registers
1.00
0.70
0.60
0.60
DS13314 Rev 3
µA/MHz
STM32H733xG
Electrical characteristics
Table 29. Peripheral current consumption in Run mode (continued)
IDD(Typ)
Peripheral
APB1
Unit
VOS0
VOS1
VOS2
VOS3
I2C2 kernel
2.30
1.90
1.70
1.20
I2C3 registers
0.90
0.60
0.50
0.50
I2C3 kernel
2.30
2.00
1.00
1.00
I2C5 registers
0.90
0.60
0.50
0.50
I2C5 kernel
2.20
2.10
1.90
1.80
CEC registers
0.60
0.30
0.20
0.20
CEC kernel
0.10
0.10
0.10
0.10
DAC1
1.60
1.30
1.10
1.10
FDCAN1/2/3 registers
24.10
20.90
18.20
17.40
FDCAN1/2/3 kernel
9.90
9.90
9.00
8.00
CRS
4.90
3.90
3.50
3.20
SWPMI registers
1.10
0.80
0.80
0.80
SWPMI kernel
1.50
1.10
1.00
1.00
OPAMP
0.50
0.40
0.30
0.20
DS13314 Rev 3
µA/MHz
109/236
216
Electrical characteristics
STM32H733xG
Table 29. Peripheral current consumption in Run mode (continued)
IDD(Typ)
Peripheral
APB2
110/236
Unit
VOS0
VOS1
VOS2
VOS3
TIM1
5.30
4.40
4.20
3.80
TIM8
5.60
5.40
5.20
3.90
USART1 registers
1.80
1.60
1.40
1.10
USART1 kernel
3.00
2.90
2.80
2.70
USART6 registers
1.90
1.70
1.50
1.20
USART6 kernel
4.50
4.00
3.60
3.10
UART9 registers
1.70
1.70
1.60
1.10
UART9 kernel
3.80
3.30
2.90
2.90
USART10 registers
1.80
1.70
1.40
1.10
USART10 kernel
3.80
3.30
2.90
2.90
SPI1 registers
1.90
1.80
1.40
1.20
SPI1 kernel
1.50
1.20
1.10
1.00
SPI4 registers
1.80
1.60
1.40
1.10
SPI4 kernel
1.50
1.20
1.10
1.00
SPI5 registers
1.60
1.60
1.40
1.10
SPI5 kernel
1.50
1.20
1.10
1.00
TIM15
2.80
2.50
2.30
1.90
TIM16
2.00
1.90
1.60
1.30
TIM17
2.10
2.00
1.70
1.40
SAI1 registers
1.40
1.40
1.20
0.90
SAI1 kernel
0.80
0.70
0.70
0.70
DFSDM1 registers
5.60
5.40
5.30
4.00
DFSDM1 kernel
0.30
0.20
0.20
0.10
SYSCFG
1.20
1.10
1.10
1.10
DS13314 Rev 3
µA/MHz
STM32H733xG
Electrical characteristics
Table 29. Peripheral current consumption in Run mode (continued)
IDD(Typ)
Peripheral
APB4
Unit
VOS0
VOS1
VOS2
VOS3
LPUART1 registers
1.80
0.90
0.80
0.60
LPUART1 kernel
2.40
2.30
2.00
1.90
SPI6 registers
2.60
2.30
2.10
1.80
SPI6 kernel
1.20
1.10
1.00
0.90
I2C4 registers
0.70
0.70
0.60
0.40
I2C4 kernel
2.00
1.70
1.70
1.40
LPTIM2 registers
1.50
0.70
0.50
0.30
LPTIM2 kernel
2.50
2.10
2.00
1.90
LPTIM3 registers
2.90
2.60
2.30
1.90
LPTIM3 kernel
2.40
2.00
1.90
1.70
LPTIM4 registers
2.60
2.30
2.10
1.80
LPTIM4 kernel
2.10
1.80
1.70
1.60
LPTIM5 registers
2.60
2.30
2.00
1.70
LPTIM5 kernel
2.10
1.80
1.60
1.50
COMP1/2
0.70
0.30
0.20
0.10
VREF
0.10
0.10
0.10
0.10
RTC
0.10
0.10
0.10
0.10
WWDG1
0.60
0.50
0.50
0.50
SAI4 registers
2.40
2.20
2.10
1.70
SAI4 kernel
0.90
0.90
0.90
0.70
DTS
2.90
2.60
2.30
2.00
DS13314 Rev 3
µA/MHz
111/236
216
Electrical characteristics
6.3.8
STM32H733xG
Wakeup time from low-power modes
The wakeup times given in Table 30 are measured starting from the wakeup event trigger up
to the first instruction executed by the CPU:
•
For Stop or Sleep modes: the wakeup event is WFE.
•
WKUP (PC1) pin is used to wakeup from Standby, Stop and Sleep modes.
All timings are derived from tests performed under ambient temperature and VDD=3.3 V.
Table 30. Low-power mode wakeup timings
Max(1)
Symbol
Parameter
Conditions
Typ(1)
tWUSLEEP(3)
Wakeup from Sleep
-
14.00
15.00
SVOS3, HSI, Flash memory in Normal mode
4.6
6.2
SVOS3, HSI, Flash memory in low-power mode
12.4
17.4
SVOS4, HSI, Flash memory in Normal mode
15.5
21.1
SVOS4, HSI, Flash memory in low-power mode
23.3
31.8
SVOS5, HSI, Flash memory in Normal mode
39.1
52.6
SVOS5, HSI, Flash memory in low-power mode
39.1
52.7
SVOS3, CSI, Flash memory in Normal mode
30.0
41.6
SVOS3, CSI, Flash memory in low-power mode
40.6
55.0
SVOS4, CSI, Flash memory in Normal mode
41.0
55.4
SVOS4, CSI, Flash memory in low-power mode
51.5
68.8
SVOS5, CSI, Flash memory in Normal mode
67.3
89.5
SVOS5, CSI, Flash memory in low-power mode
67.2
89.5
-
400.0
504.3
tWUSTOP(3)
tWUSTDBY(3)
Wakeup from Stop
mode
Wakeup from
Standby mode
(2)
1. Guaranteed by characterization results.
2. The maximum values have been measured at -40 °C, in worst conditions.
3. The wakeup times are measured from the wakeup event to the point in which the application code reads the first
112/236
DS13314 Rev 3
Unit
CPU
clock
cycles
µs
STM32H733xG
6.3.9
Electrical characteristics
External clock source characteristics
High-speed external user clock generated from an external source
In bypass mode the HSE oscillator is switched off and the input pin is a standard I/O.
The external clock signal has to respect the Table 51: I/O static characteristics. However,
the recommended clock input waveform is shown in Figure 13.
Table 31. High-speed external user clock characteristics(1)
Symbol
Parameter
Min
Typ
Max
Unit
fHSE_ext
User external clock source frequency
4
25
50
MHz
VHSEH
Digital OSC_IN input high-level
voltage
0.7 VDD
-
VDD
VHSEL
Digital OSC_IN input low-level voltage
VSS
-
0.3 VDD
tW(HSE)
OSC_IN high or low time
7
-
-
V
ns
1. Guaranteed by design.
Figure 13. High-speed external clock source AC timing diagram
VHSEH
90 %
10 %
VHSEL
tr(HSE)
tf(HSE)
tW(HSE) t
tW(HSE)
THSE
External
clock source
fHSE_ext
OSC_IN
IL
STM32
ai17528b
DS13314 Rev 3
113/236
216
Electrical characteristics
STM32H733xG
Low-speed external user clock generated from an external source
In bypass mode the LSE oscillator is switched off and the input pin is a standard I/O. The
external clock signal has to respect the Table 51: I/O static characteristics. However, the
recommended clock input waveform is shown in Figure 14.
Table 32. Low-speed external user clock characteristics(1)
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
kHz
fLSE_ext
User external clock source
frequency
-
-
32.768
1000
VLSEH
OSC32_IN input pin high-level
voltage
-
0.7 VDD
-
VDD
VLSEL
OSC32_IN input pin low-level
voltage
-
VSS
-
0.3 VDD
OSC32_IN high or low time
-
250
-
-
tw(LSEH)
tw(LSEL)
V
ns
1. Guaranteed by design.
Figure 14. Low-speed external clock source AC timing diagram
VLSEH
90%
VLSEL
10%
tr(LSE)
tf(LSE)
tW(LSE)
OSC32_IN
IL
tW(LSE) t
TLSE
External
clock source
fLSE_ext
STM32
ai17529b
114/236
DS13314 Rev 3
STM32H733xG
Electrical characteristics
High-speed external clock generated from a crystal/ceramic resonator
The high-speed external (HSE) clock can be supplied with a 4 to 50 MHz crystal/ceramic
resonator oscillator. All the information given in this paragraph are based on
characterization results obtained with typical external components specified in Table 33. In
the application, the resonator and the load capacitors have to be placed as close as
possible to the oscillator pins in order to minimize output distortion and startup stabilization
time. Refer to the crystal resonator manufacturer for more details on the resonator
characteristics (frequency, package, accuracy).
Table 33. 4-50 MHz HSE oscillator characteristics(1)
Symbol
Parameter
Operating
conditions(2)
Min
Typ
Max
Unit
F
Oscillator frequency
-
4
-
50
MHz
RF
Feedback resistor
-
-
200
-
kΩ
During startup(3)
-
-
4
VDD=3 V, Rm=30 Ω
CL=10 pF at 4 MHz
-
0.35
-
VDD=3 V, Rm=30 Ω
CL=10 pF at 8 MHz
-
0.40
-
VDD=3 V, Rm=30 Ω
CL=10 pF at 16 MHz
-
0.45
-
VDD=3 V, Rm=30 Ω
CL=10 pF at 32 MHz
-
0.65
-
VDD=3 V, Rm=30 Ω
CL=10 pF at 48 MHz
-
0.95
-
IDD(HSE)
HSE current
consumption
mA
Gmcritmax
Maximum critical crystal
gm
Startup
-
-
1.5
mA/V
tSU(4)
Start-up time
VDD is stabilized
-
2
-
ms
1. Guaranteed by design.
2. Resonator characteristics given by the crystal/ceramic resonator manufacturer.
3. This consumption level occurs during the first 2/3 of the tSU(HSE) startup time.
4. tSU(HSE) is the startup time measured from the moment it is enabled (by software) to a stabilized 8 MHz
oscillation is reached. This value is measured for a standard crystal resonator and it can vary significantly
with the crystal manufacturer.
For CL1 and CL2, it is recommended to use high-quality external ceramic capacitors in the
5 pF to 25 pF range (typical), designed for high-frequency applications, and selected to
match the requirements of the crystal or resonator (see Figure 15). CL1 and CL2 are usually
the same size. The crystal manufacturer typically specifies a load capacitance which is the
series combination of CL1 and CL2. The PCB and MCU pin capacitance must be included
(10 pF can be used as a rough estimate of the combined pin and board capacitance) when
sizing CL1 and CL2.
Note:
For information on selecting the crystal, refer to application note AN2867 “Oscillator design
guide for ST microcontrollers” available from the ST website www.st.com.
DS13314 Rev 3
115/236
216
Electrical characteristics
STM32H733xG
Figure 15. Typical application with an 8 MHz crystal
Resonator with
integrated capacitors
CL1
8 MHz
resonator
CL2
fHSE
OSC_IN
REXT(1)
RF
Bias
controlled
gain
OSC_OU T
STM32
ai17530b
1. REXT value depends on the crystal characteristics.
Low-speed external clock generated from a crystal/ceramic resonator
The low-speed external (LSE) clock can be supplied with a 32.768 kHz crystal/ceramic
resonator oscillator. All the information given in this paragraph are based on
characterization results obtained with typical external components specified in Table 34. In
the application, the resonator and the load capacitors have to be placed as close as
possible to the oscillator pins in order to minimize output distortion and startup stabilization
time. Refer to the crystal resonator manufacturer for more details on the resonator
characteristics (frequency, package, accuracy).
Table 34. Low-speed external user clock characteristics(1)
Symbol
Parameter
Operating conditions(2)
Min
Typ
Max
Unit
F
Oscillator frequency
-
-
32.768
-
kHz
LSEDRV[1:0] = 00,
Low drive capability
-
290
-
LSEDRV[1:0] = 01,
Medium Low drive capability
-
390
-
LSEDRV[1:0] = 10,
Medium high drive capability
-
550
-
LSEDRV[1:0] = 11,
High drive capability
-
900
-
LSEDRV[1:0] = 00,
Low drive capability
-
-
0.5
LSEDRV[1:0] = 01,
Medium Low drive capability
-
-
0.75
LSEDRV[1:0] = 10,
Medium high drive capability
-
-
1.7
LSEDRV[1:0] = 11,
High drive capability
-
-
2.7
VDD is stabilized
-
2
-
IDD
Gmcritmax
tSU(3)
LSE current
consumption
Maximum critical crystal
gm
Startup time
nA
µA/V
s
1. Guaranteed by design.
2. Refer to the note and caution paragraphs below the table, and to the application note AN2867 “Oscillator design guide for
ST microcontrollers”.
3. tSU is the startup time measured from the moment it is enabled (by software) to a stabilized 32.768k Hz oscillation is
reached. This value is measured for a standard crystal resonator and it can vary significantly with the crystal manufacturer.
116/236
DS13314 Rev 3
STM32H733xG
Note:
Electrical characteristics
For information on selecting the crystal, refer to the application note AN2867 “Oscillator
design guide for ST microcontrollers” available from the ST website www.st.com.
Figure 16. Typical application with a 32.768 kHz crystal
Resonator with
integrated capacitors
CL1
fHSE
OSC32_IN
32.768 kHz
resonator
RF
Bias
controlled
gain
OSC32_OUT
STM32
CL2
ai17531c
1. An external resistor is not required between OSC32_IN and OSC32_OUT and it is forbidden to add one.
6.3.10
Internal clock source characteristics
The parameters given in Table 35 to Table 37 are derived from tests performed under
ambient temperature and VDD supply voltage conditions summarized in Table 12: General
operating conditions.
48 MHz high-speed internal RC oscillator (HSI48)
Table 35. HSI48 oscillator characteristics
Symbol
fHSI48
TRIM(2)
Parameter
Conditions
Min
Typ
Max
Unit
VDD=3.3 V,
TJ=30 °C
47.5(1)
48
48.5(1)
MHz
-
-
0.175
0.250
%
± 32 steps
±4.70
±5.6
-
%
-
45
-
55
%
TJ=-40 to 125 °C
–4.5
-
3.5
%
VDD=3 to 3.6 V
-
0.025
0.05
VDD=1.62 V to 3.6 V
-
0.05
0.1
HSI48 frequency
USER trimming step
USER TRIM
COVERAGE(3)
USER TRIMMING coverage
DuCy(HSI48)(2)
Duty Cycle
ACCHSI48_REL(3)(4)
Accuracy of the HSI48 oscillator over
temperature (factory calibrated)
∆VDD(HSI48)(2)(5)
HSI48 oscillator frequency drift with
VDD(6) (the reference is 3.3 V)
%
tsu(HSI48)(2)
HSI48 oscillator start-up time
-
-
2.1
4.0
µs
IDD(HSI48)(2)
HSI48 oscillator power consumption
-
-
350
400
µA
NT jitter(2)
Next transition jitter
Accumulated jitter on 28 cycles(7)
-
-
± 0.15
-
ns
PT jitter(2)
Paired transition jitter
Accumulated jitter on 56 cycles(7)
-
-
± 0.25
-
ns
1. Guaranteed by test in production.
2. Guaranteed by design.
3. Guaranteed by characterization results.
4.
∆fHSI = ACCHSI48_REL + ∆VDD.
DS13314 Rev 3
117/236
216
Electrical characteristics
5.
STM32H733xG
∆fHSI = ACCHSI48_REL + ∆VDD.
6. These values are obtained by using the formula: (Freq(3.6 V) - Freq(3.0 V)) / Freq(3.0 V) or (Freq(3.6 V) - Freq(1.62 V)) /
Freq(1.62 V).
7. Jitter measurements are performed without clock source activated in parallel.
64 MHz high-speed internal RC oscillator (HSI)
Table 36. HSI oscillator characteristics(1)
Symbol
fHSI
TRIM
Parameter
HSI frequency
HSI user trimming step
DuCy(HSI)
Duty cycle
ΔVDD (HSI)
HSI oscillator frequency drift over
VDD (the reference is 3.3 V)
ΔTEMP(HSI)
HSI oscillator frequency drift over
temperature (the reference is
64 MHz)
tsu(HSI)
HSI oscillator start-up time
tstab(HSI)
HSI oscillator stabilization time
IDD(HSI)
HSI oscillator power consumption
Conditions
Min
Typ
Max
Unit
VDD=3.3 V, TJ=30 °C
63.7(2)
64
64.3(2)
MHz
Trimming is not a multiple
of 32
-
0.24
0.32
Trimming is 128, 256 and
384
−5.2
−1.8
-
Trimming is 64, 192, 320
and 448
−1.4
−0.8
-
Other trimming are a
multiple of 32 (not
including multiple of 64
and 128)
−0.6
−0.25
-
-
45
-
55
%
VDD=1.62 to 3.6 V
−0.12
-
0.03
%
TJ=-20 to 105 °C
−1(3)
-
1(3)
TJ=−40 to TJmax °C
−2(3)
-
1(3)
-
-
1.4
2
at 1% of target frequency
-
4
8
at 5% of target frequency
-
-
4
-
-
300
400
1. Guaranteed by design unless otherwise specified.
2. Guaranteed by test in production.
3. Guaranteed by characterization results.
118/236
DS13314 Rev 3
%
%
µs
µA
STM32H733xG
Electrical characteristics
4 MHz low-power internal RC oscillator (CSI)
Table 37. CSI oscillator characteristics(1)
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
VDD=3.3 V, TJ=30 °C
3.96(2)
4
4.04(2)
MHz
Trimming is not a
multiple of 16
-
0.40
0.75
Trimming is a multiple
of 32
−4.75
−2.75
0.75
Other trimming values
not multiple of 16
(excluding multiple of
32)
−0.43
0.00
0.75
-
45
-
55
TJ = 0 to 85 °C
−3.7(3)
-
4.5(3)
TJ = −40 to 125 °C
−11(3)
-
7.5(3)
VDD = 1.62 to 3.6 V
−0.06
-
0.06
%
CSI oscillator startup time
-
-
1
2
µs
tstab(CSI)
CSI oscillator stabilization time
(to reach ± 3% of fCSI)
-
-
-
4
cycle
IDD(CSI)
CSI oscillator power consumption
-
-
23
30
µA
Min
Typ
Max
Unit
VDD = 3.3 V, TJ = 25 °C
31.4(1)
32
32.6(1)
TJ = –40 to 110 °C,
VDD = 1.62 to 3.6 V
29.76(2)
-
33.6(2)
TJ = –40 to 125 °C,
VDD = 1.62 to 3.6 V
29.4(2)
-
33.6(2)
fCSI
CSI frequency
TRIM
CSI trimming step
DuCy(CSI)
Duty cycle
∆TEMP (CSI)
CSI oscillator frequency drift over
temperature
∆VDD (CSI)
CSI oscillator frequency drift over
VDD
tsu(CSI)
%
%
%
1. Guaranteed by design, unless otherwise specified.
2. Guaranteed by test in production.
3. Guaranteed by characterization results.
Low-speed internal (LSI) RC oscillator
Table 38. LSI oscillator characteristics
Symbol
fLSI
tsu(LSI)(3)
Parameter
LSI frequency
Conditions
LSI oscillator startup time
-
-
80
130
tstab(LSI)(3)
LSI oscillator stabilization time
(5% of final value)
-
-
120
170
IDD(LSI)(3)
LSI oscillator power consumption
-
-
130
280
kHz
µs
nA
1. Guaranteed by test in production.
2. Guaranteed by characterization results.
3. Guaranteed by design.
DS13314 Rev 3
119/236
216
Electrical characteristics
6.3.11
STM32H733xG
PLL characteristics
The parameters given in Table 39, Table 42 are derived from tests performed under
temperature and VDD supply voltage conditions summarized in Table 12: General operating
conditions.
Table 39. PLL1 characteristics (wide VCO frequency range)(1)
Symbol
fPLL_IN
fPLL_P_OUT
fVCO_OUT
tLOCK
Parameter
Conditions
Min
Typ
Max
Unit
PLL input clock
-
2
-
16
MHz
PLL input clock duty cycle
-
10
-
90
%
PLL multiplier output clock P
VOS0
1.5
-
550
VOS1
1.5
-
400(2)
VOS2
1.5
-
300(2)
VOS3
1.5
-
170(2)
-
192
-
836(3)
Normal mode
15
50
150(3)
Sigma-delta mode (CKIN ≥
8 MHz)
25
65
170
fVCO_OUT
= 192 MHz
-
51
-
fVCO_OUT
= 400 MHz
-
19
-
fVCO_OUT
= 560 MHz
-
10
-
fVCO_OUT
= 800 MHz
-
9
-
fVCO_OUT
= 192 MHz
-
38
-
fVCO_OUT
= 560 MHz
-
8
-
fVCO_OUT
= 800 MHz
-
7
-
fVCO_OUT
= 192 MHz
-
0.15
-
fVCO_OUT
= 400 MHz
-
0.14
-
fVCO_OUT
= 832 MHz
-
0.16
-
fVCO_OUT
= 192 MHz
-
0.17
-
fVCO_OUT
= 500 MHz
-
0.08
-
fVCO_OUT
= 836 MHz
-
0.06
-
PLL VCO output
PLL lock time
Cycle-to-cycle jitter(4)
fPLL_OUT =
fVCO_OUT/100
Period jitter
Jitter
Normal mode
(CKIN = 2 MHz)
Long term jitter
Sigma-delta
mode (CKIN =
16 MHz)
120/236
(2)
DS13314 Rev 3
MHz
µs
ps
%
STM32H733xG
Electrical characteristics
Table 39. PLL1 characteristics (wide VCO frequency range)(1) (continued)
Symbol
Parameter
Conditions
fVCO_OUT =
560 MHz
IDD(PLL)
PLL power consumption
fVCO_OUT =
192 MHz
Min
Typ
Max
Unit
VDDA
530
557
670
VCORE
1190
1285
6300
VDDA
260
286
513
VCORE
309
377
5700
µA
1. Guaranteed by design unless otherwise specified.
2. This value must be limited to the maximum frequency due to the product limitation.
3. Guaranteed by characterization results.
4. Integer mode only.
Table 40. PLL1 characteristics (medium VCO frequency range)(1)
Symbol
fPLL_IN
fPLL_OUT
fVCO_OUT
tLOCK
Parameter
Conditions
Min
Typ
Max
Unit
PLL input clock
-
1
-
2
MHz
PLL input clock duty cycle
-
10
-
90
%
VOS0
1.17
-
210
VOS1
1.17
-
210
VOS2
1.17
-
210
VOS3
1.17
-
200
-
150
-
420
-
60(2)
100(2)
PLL multiplier output clock P, Q, R
PLL VCO output
Normal mode
PLL lock time
Cycle-to-cycle
Sigma-delta mode
jitter(3)
-
Jitter
Period jitter
Long term jitter
fPLL_OUT =
50 MHz
Normal mode
fVCO_OUT =
420 MHz
I(PLL)
PLL power consumption on VDD
fVCO_OUT =
150 MHz
DS13314 Rev 3
forbidden
fVCO_OUT =
150 MHz
-
145
-
fVCO_OUT =
300 MHz
-
91
-
fVCO_OUT =
400 MHz
-
64
-
fVCO_OUT =
420 MHz
-
63
-
fVCO_OUT =
150 MHz
-
55
-
fVCO_OUT =
400 MHz
-
30
-
fVCO_OUT =
400 MHz
-
±0.3
-
VDD
-
440
1150
VCORE
-
530
-
VDD
-
180
500
VCORE
-
200
-
MHz
µs
±ps
±-ps
%
µA
121/236
216
Electrical characteristics
STM32H733xG
1. Guaranteed by design unless otherwise specified.
2. Guaranteed by characterization results.
3. Integer mode only.
Table 41. PLL2 and PLL3 characteristics (wide VCO frequency range)(1)
Symbol
fPLL_IN
fPLL_OUT
Parameter
Conditions
Min
Typ
Max
Unit
PLL input clock
-
2
-
16
MHz
PLL input clock duty cycle
-
10
-
90
%
VOS0
1.5
-
550(2)
VOS1
1.5
-
400(2)
VOS2
1.5
-
300(2)
PLL multiplier output clock P,
Q, R
VOS3
1.5
-
170(2)
-
192
-
960(3)
Normal mode
-
50
150(3)
Sigma-delta mode (fPLL_IN
≥ 8 MHz)
-
58
166(3)
fVCO_OUT = 192 MHz
-
134
-
fVCO_OUT = 200 MHz
-
134
-
fVCO_OUT = 400 MHz
-
76
-
fVCO_OUT = 800 MHz
-
39
-
fVCO_OUT PLL VCO output
tLOCK
PLL lock time
Cycle-to-cycle jitter(4)
Jitter
Long term jitter
IDD(PLL)(3) PLL power consumption
Normal
mode
(fPLL_IN =
2 MHz)
fVCO_OUT =
560 MHz
-
±0.2
-
Normal
mode
(fPLL_IN =
16 MHz)
fVCO_OUT =
560 MHz
-
±0.8
-
Sigma-delta
mode
(fPLL_IN =
2 MHz)
fVCO_OUT =
560 MHz
-
±0.2
-
Sigma-delta
mode
(fPLL_IN =
16 MHz)
fVCO_OUT =
560 MHz
-
±0.8
-
VDD
-
590
1500
VCORE
-
720
-
VDD
-
180
600
VCORE
-
280
-
fVCO_OUT =
836 MHz
fVCO_OUT =
192 MHz
µs
±ps
%
1. Guaranteed by design unless otherwise specified.
2. This value must be limited to the maximum frequency due to the product limitation.
122/236
MHz
DS13314 Rev 3
µA
STM32H733xG
Electrical characteristics
3. Guaranteed by characterization results.
4. Integer mode only.
Table 42. PLL2 and PLL3 characteristics (medium VCO frequency range)(1)
Symbol
fPLL_IN
fPLL_OUT
Parameter
Conditions
Min
Typ
Max
Unit
PLL input clock
-
1
-
2
MHz
PLL input clock duty cycle
-
10
-
90
%
VOS0
1.17
-
210
MHz
VOS1
1.17
-
210
-
VOS2
1.17
-
210
-
VOS3
1.17
-
200
-
-
150
-
420
-
Normal mode
-
60
100(2)
PLL multiplier output clock
P, Q, R
fVCO_OUT PLL VCO output
tLOCK
PLL lock time
Sigma-delta mode
Cycle-to-cycle jitter(3)
Jitter
Period jitter
fVCO_OUT = 150 MHz
-
145
-
fVCO_OUT = 200 MHz
-
91
-
fVCO_OUT = 400 MHz
-
64
-
fVCO_OUT = 420 MHz
-
63
-
-
55
-
-
30
-
fVCO_OUT =
400 MHz
-
±0.3
-
VDD
-
440
1150
VCORE
-
530
-
VDD
-
180
500
VCORE
-
200
-
fPLL_OUT =
50 MHz
fVCO_OUT =
150 MHz
fVCO_OUT = 400 MHz
Long term jitter
IDD(PLL)
PLL power consumption on
VDD
forbidden
Normal mode
fVCO_OUT =
420 MHz
fVCO_OUT =
150 MHz
µs
±ps
±ps
%
µA
1. Guaranteed by design unless otherwise specified.
2. Guaranteed by characterization results.
3. Integer mode only.
DS13314 Rev 3
123/236
216
Electrical characteristics
6.3.12
STM32H733xG
Memory characteristics
Flash memory
The characteristics are given at TJ = –40 to 125 °C unless otherwise specified.
The devices are shipped to customers with the Flash memory erased.
Table 43. Flash memory characteristics
Symbol
IDD
Parameter
Supply current
Conditions
Min
Typ
Max
Unit
Write / Erase 8-bit mode
-
6.5
-
Write / Erase 16-bit mode
-
11.5
-
Write / Erase 32-bit mode
-
20
-
Write / Erase 64-bit mode
-
35
-
Min(1)
Typ
Max(1)
mA
Table 44. Flash memory programming
Symbol
tprog
tERASE
tME
Parameter
Conditions
Program/erase parallelism x 8
-
290
580(2)
Program/erase parallelism x 16
-
180
360
Program/erase parallelism x 32
-
130
260
Program/erase parallelism x 64
-
100
200
Program/erase parallelism x 8
-
2
4
Sector (128 Kbytes) erase time Program/erase parallelism x 16
-
1.8
3.6
Program/erase parallelism x 32
-
Program/erase parallelism x 8
-
3
26
Program/erase parallelism x 16
-
8
16
Program/erase parallelism x 32
-
6
12
Program/erase parallelism x 64
-
5
10
1.62
-
3.6
1.8
-
3.6
Word (266 bits) programming
time
Mass erase time (1 Mbyte)
Unit
µs
s
Program parallelism x 8
Vprog
Programming voltage
Program parallelism x 16
Program parallelism x 32
Program parallelism x 64
V
1. Guaranteed by characterization results.
2. The maximum programming time is measured after 10K erase operations.
Table 45. Flash memory endurance and data retention
Symbol
NEND
tRET
124/236
Parameter
Conditions
Min(1)
Unit
kcycles
Endurance
TJ = –40 to +125 °C
10
Data retention
1 kcycle at TA = 85 °C
30
10 kcycles at TA = 55 °C
20
DS13314 Rev 3
Years
STM32H733xG
Electrical characteristics
1. Guaranteed by characterization results.
6.3.13
EMC characteristics
Susceptibility tests are performed on a sample basis during device characterization.
Functional EMS (electromagnetic susceptibility)
While a simple application is executed on the device (toggling 2 LEDs through I/O ports).
the device is stressed by two electromagnetic events until a failure occurs. The failure is
indicated by the LEDs:
•
Electrostatic discharge (ESD) (positive and negative) is applied to all device pins until
a functional disturbance occurs. This test is compliant with the IEC 61000-4-2 standard.
•
FTB: A burst of fast transient voltage (positive and negative) is applied to VDD and VSS
through a 100 pF capacitor, until a functional disturbance occurs. This test is compliant
with the IEC 61000-4-4 standard.
A device reset allows normal operations to be resumed.
The test results are given in Table 46. They are based on the EMS levels and classes
defined in application note AN1709 “EMC design guide for STM8, STM32 and Legacy
MCUs ”.
Table 46. EMS characteristics
Symbol
Parameter
Conditions
Level/
Class
VFESD
VDD = 3.3 V, TA = 25 °C,
Voltage limits to be applied on any I/O pin to induce
LQFP176, conforming to
a functional disturbance
IEC 61000-4-2
3B
VFTB
Fast transient voltage burst limits to be applied
through 100 pF on VDD and VSS pins to induce a
functional disturbance
5A
VDD = 3.3 V, TA = 25 °C,
LQFP176, conforming to
IEC 61000-4-4
As a consequence, it is recommended to add a serial resistor (1 kΏ) located as close as
possible to the MCU to the pins exposed to noise (connected to tracks longer than 50 mm
on PCB).
Designing hardened software to avoid noise problems
EMC characterization and optimization are performed at component level with a typical
application environment and simplified MCU software. It should be noted that good EMC
performance is highly dependent on the user application and the software in particular.
Therefore it is recommended that the user applies EMC software optimization and
prequalification tests in relation with the EMC level requested for his application.
Software recommendations
The software flowchart must include the management of runaway conditions such as:
•
Corrupted program counter
•
Unexpected reset
•
Critical Data corruption (control registers...)
DS13314 Rev 3
125/236
216
Electrical characteristics
STM32H733xG
Prequalification trials
Most of the common failures (unexpected reset and program counter corruption) can be
reproduced by manually forcing a low state on the NRST pin or the Oscillator pins for 1
second.
To complete these trials, ESD stress can be applied directly on the device, over the range of
specification values. When unexpected behavior is detected, the software can be hardened
to prevent unrecoverable errors occurring (see application note AN1015 “Software
techniques for improving microcontrollers EMC performance”).
Electromagnetic Interference (EMI)
The electromagnetic field emitted by the device are monitored while a simple application,
executing EEMBC code, is running. This emission test is compliant with SAE IEC61967-2
standard which specifies the test board and the pin loading.
Table 47. EMI characteristics
Symbol Parameter
Conditions
Max vs.
[fHSE/fCPU]
Monitored
frequency band
Unit
8/550 MHz
SEMI
6.3.14
VDD = 3.6 V, TA = 25 °C, LQFP176 package,
Peak level
conforming to IEC61967-2
0.1 to 30 MHz
14
30 to 130 MHz
20
130 MHz to 1 GHz
27
1 GHz to 2 GHz
17
EMI Level
4
dBµV
-
Absolute maximum ratings (electrical sensitivity)
Based on three different tests (ESD, LU) using specific measurement methods, the device is
stressed in order to determine its performance in terms of electrical sensitivity.
Electrostatic discharge (ESD)
Electrostatic discharges (a positive then a negative pulse) are applied to the pins of each
sample according to each pin combination. This test conforms to the ANSI/ESDA/JEDEC
JS-001 and ANSI/ESDA/JEDEC JS-002 standards.
Table 48. ESD absolute maximum ratings
Symbol
VESD(HBM)
Ratings
Conditions
Electrostatic discharge
TA = 25 °C conforming to
voltage (human body model) ANSI/ESDA/JEDEC JS-001
Electrostatic discharge
VESD(CDM) voltage (charge device
model)
TA = +25 °C conforming to
ANSI/ESDA/JEDEC JS-002
1. Guaranteed by characterization results.
126/236
DS13314 Rev 3
Maximum
Unit
value(1)
Packages
Class
All packages
2
2000
All LQFP
packages
C1
250
All BGA and
WLCSP packages
C2a
500
V
STM32H733xG
Electrical characteristics
Static latchup
Two complementary static tests are required on six parts to assess the latchup
performance:
•
A supply overvoltage is applied to each power supply pin
•
A current injection is applied to each input, output and configurable I/O pin
These tests are compliant with JESD78 IC latchup standard.
Table 49. Electrical sensitivities
Symbol
LU
6.3.15
Parameter
Static latchup class
Conditions
Class
Conforming to JESD78,
TJ = TJMax
II level A
I/O current injection characteristics
As a general rule, a current injection to the I/O pins, due to external voltage below VSS or
above VDD (for standard, 3.3 V-capable I/O pins) should be avoided during the normal
product operation. However, in order to give an indication of the robustness of the
microcontroller in cases when an abnormal injection accidentally happens, susceptibility
tests are performed on a sample basis during the device characterization.
Functional susceptibility to I/O current injection
While a simple application is executed on the device, the device is stressed by injecting
current into the I/O pins programmed in floating input mode. While current is injected into
the I/O pin, one at a time, the device is checked for functional failures.
The failure is indicated by an out of range parameter: ADC error above a certain limit (higher
than 5 LSB TUE), out of conventional limits of induced leakage current on adjacent pins (out
of –5 µA/+0 µA range), or other functional failure (for example reset, oscillator frequency
deviation).
The following tables are the compilation of the SIC1/SIC2 and functional ESD results.
Negative induced A negative induced leakage current is caused by negative injection and
positive induced leakage current by positive injection.
Table 50. I/O current injection susceptibility(1)
Functional susceptibility
Symbol
IINJ
Description
Negative
injection
Positive
injection
PA12, PE8
5
0
PC4, PE12, PF15, PH0
0
NA
PA0, PA0_C, PA1, PA1_C, PC2, PC2_C, PC3, PC3_C, PA4,
PA5, PE7, PG1, PH4, PH5, BOOT0
0
0
All other I/Os
5
NA
Unit
mA
1. Guaranteed by characterization results.
DS13314 Rev 3
127/236
216
Electrical characteristics
6.3.16
STM32H733xG
I/O port characteristics
General input/output characteristics
Unless otherwise specified, the parameters given in Table 51: I/O static characteristics are
derived from tests performed under the conditions summarized in Table 12: General
operating conditions. All I/Os are CMOS and TTL compliant (except for BOOT0).
Note:
For information on GPIO configuration, refer to application note AN4899 “STM32 GPIO
configuration for hardware settings and low-power consumption”, available from the ST
website www.st.com.
Table 51. I/O static characteristics
Symbol
Parameter
Condition
Min
Typ
Max
-
-
0.3VDD(1)
-
-
0.4VDD−0.1
BOOT0 I/O input low level
voltage
-
-
0.19VDD+0.1
I/O input high level voltage
except BOOT0
0.7VDD(1)
-
-
0.47VDD+
0.25(2)
-
-
0.17VDD+
0.6(2)
-
-
-
250
-
-
200
-
-
-
+/-250
Max(VDDXXX) < VIN ≤ 5.5 V
(4)(5)(8)
-
-
1500
0< VIN ≤ Max(VDDXXX)(8)
-
-
+/- 350
Max(VDDXXX) < VIN ≤ 5.5 V
(4)(5)(8)
-
-
5000(6)
0< VIN ≤ Max(VDDXXX) (8)
-
-
+/-250
0< VIN ≤ VDD
-
-
15
I/O input low level voltage
except BOOT0
VIL
VIH
I/O input low level voltage
except BOOT0
I/O input high level voltage
except BOOT0
1.62 V<VDD<3.6 V
1.62 V<VDD<3.6 V
BOOT0 I/O input high level
voltage
VHYS(2)
TT_xx, FT_xxx and NRST I/O
input hysteresis
1.62 V< VDD <3.6 V
BOOT0 I/O input hysteresis
0< VIN ≤
FT_xx Input leakage
Ilkg(3)
current(2)
FT_u IO
TT_xx Input leakage current
VPP (BOOT0 alternate
function)
RPU
Weak pull-up equivalent
resistor(7)
RPD
Weak pull-down equivalent
resistor(7)
CIO
I/O pin capacitance
Max(VDDXXX)(8)
VDD < VIN ≤ 9 V
VIN=VSS
V
(2)
V
mV
nA
35
30
40
50
kΩ
VIN=VDD
(8)
-
1. Compliant with CMOS requirements.
2. Guaranteed by design.
128/236
(2)
Unit
DS13314 Rev 3
30
40
50
-
5
-
pF
STM32H733xG
Electrical characteristics
3. This parameter represents the pad leakage of the I/O itself. The total product pad leakage is provided by the following
formula: ITotal_Ieak_max = 10 μA + [number of I/Os where VIN is applied on the pad] ₓ Ilkg(Max).
4. All FT_xx IO except FT_lu, FT_u and PC3.
5. VIN must be less than Max(VDDXXX) + 3.6 V.
6. To sustain a voltage higher than MIN(VDD, VDDA, VDD33USB) +0.3 V, the internal pull-up and pull-down resistors must be
disabled.
7. The pull-up and pull-down resistors are designed with a true resistance in series with a switchable PMOS/NMOS. This
PMOS/NMOS contribution to the series resistance is minimal (~10% order).
8. Max(VDDXXX) is the maximum value of all the I/O supplies.
All I/Os are CMOS and TTL compliant (no software configuration required). Their
characteristics cover more than the strict CMOS-technology or TTL parameters. The
coverage of these requirements for FT I/Os is shown in Figure 17.
Figure 17. VIL/VIH for all I/Os except BOOT0
3
2.5
=0.7
min
t: V IH
men
uire
S req
CMO
Voltage
TLL requirement: VIHmin = 2 V
V DD
2
ulation
n sim
ased o
1.5
+0.25
0.47VDD
VIHmin=
B
-0.1
0.4VDD
VILmax=
ulation
im
s
n
V
DD
o
=0.3
Based
max
ment: VIL
require
CMOS
TLL requirement: VILmin = 0.8 V
1
0.5
0
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
MSv46121V3
Output driving current
The GPIOs (general purpose input/outputs) can sink or source up to ±8 mA, and sink or
source up to ±20 mA (with a relaxed VOL/VOH).
In the user application, the number of I/O pins which can drive current must be limited to
respect the absolute maximum rating specified in Section 6.2. In particular:
•
The sum of the currents sourced by all the I/Os on VDD, plus the maximum Run
consumption of the MCU sourced on VDD, cannot exceed the absolute maximum rating
ΣIVDD (see Table 10).
•
The sum of the currents sunk by all the I/Os on VSS plus the maximum Run
consumption of the MCU sunk on VSS cannot exceed the absolute maximum rating
ΣIVSS (see Table 10).
DS13314 Rev 3
129/236
216
Electrical characteristics
STM32H733xG
Output voltage levels
Unless otherwise specified, the parameters given in Table 52: Output voltage characteristics
for all I/Os except PC13, PC14 and PC15 and Table 53: Output voltage characteristics for
PC13, PC14 and PC15 are derived from tests performed under ambient temperature and
VDD supply voltage conditions summarized in Table 12: General operating conditions. All
I/Os are CMOS and TTL compliant.
Table 52. Output voltage characteristics for all I/Os except PC13, PC14 and PC15(1)
Symbol
Parameter
Conditions(3)
Min
Max
Output low level voltage
CMOS
IIO = 8 mA
2.7 V≤ VDD ≤3.6 V
-
0.4
Output high level voltage
CMOS port(2)
IIO = −8 mA
2.7 V≤ VDD ≤3.6 V
VDD−0.4
-
Output low level voltage
TTL port(2)
IIO = 8 mA
2.7 V≤ VDD ≤3.6 V
-
0.4
Output high level voltage
TTL port(2)
IIO = −8 mA
2.7 V≤ VDD ≤3.6 V
2.4
-
VOL(3)
Output low level voltage
IIO = 20 mA
2.7 V≤ VDD ≤3.6 V
-
1.3
VOH(3)
Output high level voltage
IIO = −20 mA
2.7 V≤ VDD ≤3.6 V
VDD−1.3
-
VOL(3)
Output low level voltage
IIO = 4 mA
1.62 V≤ VDD ≤3.6 V
-
0.4
VOH (3)
Output high level voltage
IIO = −4 mA
1.62 V≤VDD<3.6 V
VDD−-0.4
-
IIO = 20 mA
2.3 V≤ VDD≤3.6 V
-
0.4
IIO = 10 mA
1.62 V≤ VDD ≤3.6 V
-
0.4
Unit
port(2)
VOL
VOH
VOL(3)
VOH
(3)
VOLFM+(3)
Output low level voltage for an FTf
I/O pin in FM+ mode
V
1. The IIO current sourced or sunk by the device must always respect the absolute maximum rating specified in Table 9:
Voltage characteristics, and the sum of the currents sourced or sunk by all the I/Os (I/O ports and control pins) must always
respect the absolute maximum ratings ΣIIO.
2. TTL and CMOS outputs are compatible with JEDEC standards JESD36 and JESD52.
3. Guaranteed by design.
130/236
DS13314 Rev 3
STM32H733xG
Electrical characteristics
Table 53. Output voltage characteristics for PC13, PC14 and PC15(1)
Conditions(3)
Min
Max
Output low level voltage
CMOS port(2)
IIO = 3 mA
2.7 V≤ VDD ≤3.6 V
-
0.4
Output high level voltage
CMOS port(2)
IIO = −3 mA
2.7 V≤ VDD ≤3.6 V
VDD−0.4
-
Output low level voltage
TTL port(2)
IIO = 3 mA
2.7 V≤ VDD ≤3.6 V
-
0.4
Output high level voltage
TTL port(2)
IIO = −3 mA
2.7 V≤ VDD ≤3.6 V
2.4
-
VOL(2)
Output low level voltage
IIO = 1.5 mA
1.62 V≤ VDD ≤3.6 V
-
0.4
VOH(2)
Output high level voltage
IIO = −1.5 mA
1.62 V≤ VDD ≤3.6 V
VDD−0.4
-
Symbol
VOL
VOH
VOL(3)
VOH
(2)
Parameter
Unit
V
1. The IIO current sourced or sunk by the device must always respect the absolute maximum rating specified in Table 9:
Voltage characteristics, and the sum of the currents sourced or sunk by all the I/Os (I/O ports and control pins) must always
respect the absolute maximum ratings ΣIIO.
2. TTL and CMOS outputs are compatible with JEDEC standards JESD36 and JESD52.
3. Guaranteed by design.
DS13314 Rev 3
131/236
216
Electrical characteristics
STM32H733xG
Output buffer timing characteristics (HSLV option disabled)
The HSLV bit of SYSCFG_CCCSR register can be used to optimize the I/O speed when the
product voltage is below 2.7 V.
Table 54. Output timing characteristics (HSLV OFF)(1)
Speed
Symbol
Fmax(2)
Parameter
Maximum frequency
00
tr/tf(3)
Fmax(2)
Output high to low level
fall time and output low
to high level rise time
Maximum frequency
01
tr/tf(3)
132/236
Output high to low level
fall time and output low
to high level rise time
conditions
Min
Max
C=50 pF, 2.7 V≤ VDD≤3.6 V
-
12
C=50 pF, 1.62 V≤VDD≤2.7 V
-
3
C=30 pF, 2.7 V≤VDD≤3.6 V
-
12
C=30 pF, 1.62 V≤VDD≤2.7 V
-
3
C=10 pF, 2.7 V≤VDD≤3.6 V
-
16
C=10 pF, 1.62 V≤VDD≤2.7 V
-
4
C=50 pF, 2.7 V≤ VDD≤3.6 V
-
16.6
C=50 pF, 1.62 V≤VDD≤2.7 V
-
33.3
C=30 pF, 2.7 V≤VDD≤3.6 V
-
13.3
C=30 pF, 1.62 V≤VDD≤2.7 V
-
25
C=10 pF, 2.7 V≤VDD≤3.6 V
-
10
C=10 pF, 1.62 V≤VDD≤2.7 V
-
20
C=50 pF, 2.7 V≤ VDD≤3.6 V
-
60
C=50 pF, 1.62 V≤VDD≤2.7 V
-
15
C=30 pF, 2.7 V≤VDD≤3.6 V
-
80
C=30 pF, 1.62 V≤VDD≤2.7 V
-
15
C=10 pF, 2.7 V≤VDD≤3.6 V
-
110
C=10 pF, 1.62 V≤VDD≤2.7 V
-
20
C=50 pF, 2.7 V≤ VDD≤3.6 V
-
5.2
C=50 pF, 1.62 V≤VDD≤2.7 V
-
10
C=30 pF, 2.7 V≤VDD≤3.6 V
-
4.2
C=30 pF, 1.62 V≤VDD≤2.7 V
-
7.5
C=10 pF, 2.7 V≤VDD≤3.6 V
-
2.8
C=10 pF, 1.62 V≤VDD≤2.7 V
-
5.2
DS13314 Rev 3
Unit
MHz
ns
MHz
ns
STM32H733xG
Electrical characteristics
Table 54. Output timing characteristics (HSLV OFF)(1) (continued)
Speed
Symbol
Parameter
conditions
Min
Max
C=50 pF, 2.7 V≤VDD≤3.6 V
-
85
C=50 pF, 1.62 V≤VDD≤2.7 V(4)
-
35
-
110
C=30 pF, 1.62 V≤VDD≤2.7 V
-
40
C=10 pF, 2.7 V≤VDD≤3.6 V(4)
-
166
C=10 pF, 1.62 V≤VDD≤2.7 V(4)
-
100
-
3.8
(4)
(4)
Fmax(2)
Maximum frequency
10
C=30 pF, 2.7 V≤VDD≤3.6 V
(4)
(4)
C=50 pF, 2.7 V≤VDD≤3.6 V
(4)
C=50 pF, 1.62 V≤VDD≤2.7 V
tr/tf(3)
Output high to low level
fall time and output low
to high level rise time
-
6.9
V(4)
-
2.8
C=30 pF, 1.62 V≤VDD≤2.7 V(4)
-
5.2
C=10 pF, 2.7 V≤VDD≤3.6 V(4)
-
1.8
Vv
-
3.3
Vv
-
100
C=30 pF, 2.7 V≤VDD≤3.6
C=10 pF, 1.62 V≤VDD≤2.7
C=50 pF, 2.7 V≤VDD≤3.6
C=50 pF, 1.62 V≤VDD≤2.7 V(4)
Fmax(2)
Maximum frequency
11
-
50
C=30 pF, 2.7 V≤VDD≤3.6
Vv
-
133
C=30 pF, 1.62 V≤VDD≤2.7
V(4)
-
66
C=10 pF, 2.7 V≤VDD≤3.6 V(4)
-
220
C=10 pF, 1.62 V≤VDD≤2.7 V(4)
-
85
V(4)
-
3.3
V(4)
-
6.6
V(4)
-
2.4
C=30 pF, 1.62 V≤VDD≤2.7 V(4)
-
4.5
C=10 pF, 2.7 V≤VDD≤3.6 V(4)
-
1.5
V(4)
-
2.7
C=50 pF, 2.7 V≤VDD≤3.6
C=50 pF, 1.62 V≤VDD≤2.7
tr/tf(3)
Output high to low level
fall time and output low
to high level rise time
C=30 pF, 2.7 V≤VDD≤3.6
C=10 pF, 1.62 V≤VDD≤2.7
Unit
MHz
ns
MHz
ns
1. Guaranteed by design.
2. The maximum frequency is defined with the following conditions:
(tr+tf) ≤ 2/3 T
Skew ≤ 1/20 T
45%<Duty cycle<55%
3. The fall and rise times are defined between 90% and 10% and between 10% and 90% of the output waveform, respectively.
4. Compensation system enabled.
DS13314 Rev 3
133/236
216
Electrical characteristics
STM32H733xG
Output buffer timing characteristics (HSLV option enabled)
Table 55. Output timing characteristics (HSLV ON)(1)
Speed
Symbol
Fmax
(2)
Parameter
Maximum frequency
00
tr/tf(3)
Fmax
(2)
Output high to low level
fall time and output low
to high level rise time
Maximum frequency
01
tr/tf(3)
Fmax
(2)
Output high to low level
fall time and output low
to high level rise time
Maximum frequency
10
tr/tf(3)
Fmax
(2)
Output high to low level
fall time and output low
to high level rise time
Maximum frequency
11
tr/tf(3)
Output high to low level
fall time and output low
to high level rise time
conditions
Min
Max
C=50 pF, 1.62 V≤VDD≤2.7 V
-
10
C=30 pF, 1.62 V≤VDD≤2.7 V
-
10
C=10 pF, 1.62 V≤VDD≤2.7 V
-
10
C=50 pF, 1.62 V≤VDD≤2.7 V
-
11
C=30 pF, 1.62 V≤VDD≤2.7 V
-
9
C=10 pF, 1.62 V≤VDD≤2.7 V
-
6.6
C=50 pF, 1.62 V≤VDD≤2.7 V
-
50
C=30 pF, 1.62 V≤VDD≤2.7 V
-
58
C=10 pF, 1.62 V≤VDD≤2.7 V
-
66
C=50 pF, 1.62 V≤VDD≤2.7 V
-
6.6
C=30 pF, 1.62 V≤VDD≤2.7 V
-
4.8
C=10 pF, 1.62 V≤VDD≤2.7 V
-
3
C=50 pF, 1.62 V≤VDD≤2.7 V(4)
-
55
C=30 pF, 1.62 V≤VDD≤2.7
V(4)
-
80
C=10 pF, 1.62 V≤VDD≤2.7
V(4)
-
133
C=50 pF, 1.62 V≤VDD≤2.7
V(4)
-
5.8
C=30 pF, 1.62 V≤VDD≤2.7 V(4)
-
4
C=10 pF, 1.62 V≤VDD≤2.7
V(4)
-
2.4
C=50 pF, 1.62 V≤VDD≤2.7
V(4)
-
60
C=30 pF, 1.62 V≤VDD≤2.7
V(4)
-
90
C=10 pF, 1.62 V≤VDD≤2.7 V(4)
-
175
C=50 pF, 1.62 V≤VDD≤2.7
V(4)
-
5.3
C=30 pF, 1.62 V≤VDD≤2.7
V(4)
-
3.6
(4)
-
1.9
C=10 pF, 1.62 V≤VDD≤2.7 V
Unit
MHz
ns
MHz
ns
MHz
ns
MHz
ns
1. Guaranteed by design.
2. The maximum frequency is defined with the following conditions:
(tr+tf) ≤ 2/3 T
Skew ≤ 1/20 T
45%<Duty cycle<55%
3. The fall and rise times are defined between 90% and 10% and between 10% and 90% of the output waveform, respectively.
4. Compensation system enabled.
134/236
DS13314 Rev 3
STM32H733xG
Electrical characteristics
Analog switch between ports Pxy_C and Pxy
PA0_C, PA1_C, PC2_C and PC3_C can be connected internally to PA0, PA1, PC2 and
PC3, respectively (refer to SYSCFG_PMCR register in RM0468 reference manual). The
switch is controlled by VDDSWITCH voltage level. It is defined through BOOSTVDDSEL bit of
SYSCFG_PMCR. If the switch is closed the switch characteristics are given in the table
below.
Table 56. Pxy_C and Pxy analog switch characteristics
Parameter
Switch
impedance
6.3.17
Conditions
Min
Typ
Max
Switch control boosted
-
-
315
VDDSWITCH > 2.7 V
-
-
315
VDDSWITCH > 2.4 V
-
-
335
VDDSWITCH > 2.0 V
-
-
390
VDDSWITCH > 1.8 V
-
-
445
VDDSWITCH > 1.62 V
-
-
550
Switch control
not boosted
Unit
Ω
NRST pin characteristics
The NRST pin input driver uses CMOS technology. It is connected to a permanent pull-up
resistor, RPU (see Table 51: I/O static characteristics).
Unless otherwise specified, the parameters given in Table 57 are derived from tests
performed under the ambient temperature and VDD supply voltage conditions summarized
in Table 12: General operating conditions.
Table 57. NRST pin characteristics
Symbol
RPU(2)
Parameter
Conditions
Min
Typ
Max
Unit
VIN = VSS
30
40
50
㏀
1.71 V < VDD < 3.6 V
-
-
50
1.71 V < VDD < 3.6 V
350
-
-
1.62 V < VDD < 3.6 V
1000
-
-
Weak pull-up equivalent
resistor(1)
VF(NRST)(2) NRST Input filtered pulse
VNF(NRST)(2) NRST Input not filtered pulse
ns
1. The pull-up is designed with a true resistance in series with a switchable PMOS. This PMOS contribution
to the series resistance must be minimum (~10% order).
2. Guaranteed by design.
DS13314 Rev 3
135/236
216
Electrical characteristics
STM32H733xG
Figure 18. Recommended NRST pin protection
VDD
External
reset circuit (1)
RPU
NRST (2)
Internal Reset
Filter
0.1 μF
STM32
ai14132d
1. The reset network protects the device against parasitic resets.
2. The user must ensure that the level on the NRST pin can go below the VIL(NRST) max level specified in
Table 51. Otherwise the reset is not taken into account by the device.
6.3.18
FMC characteristics
Unless otherwise specified, the parameters given in Table 58 to Table 71 for the FMC
interface are derived from tests performed under the ambient temperature, fHCLK frequency
and VDD supply voltage conditions summarized in Table 12: General operating conditions,
with the following configuration:
•
Output speed is set to OSPEEDRy[1:0] = 11
•
Measurement points are done at CMOS levels: 0.5VDD
•
IO Compensation cell activated.
•
HSLV activated when VDD ≤ 2.7 V
•
VOS level set to VOS0.
Refer to Section 6.3.16: I/O port characteristics for more details on the input/output alternate
function characteristics.
Asynchronous waveforms and timings
Figure 19 through Figure 21 represent asynchronous waveforms and Table 58 through
Table 65 provide the corresponding timings. The results shown in these tables are obtained
with the following FMC configuration:
•
AddressSetupTime = 0x1
•
AddressHoldTime = 0x1
•
DataSetupTime = 0x1 (except for asynchronous NWAIT mode , DataSetupTime = 0x5)
•
BusTurnAroundDuration = 0x0
•
Capacitive load CL = 30 pF
In all timing tables, the TKERCK is the fmc_ker_ck clock period.
136/236
DS13314 Rev 3
STM32H733xG
Electrical characteristics
Figure 19. Asynchronous non-multiplexed SRAM/PSRAM/NOR read waveforms
tw(NE)
FMC_NE
tv(NOE_NE)
t w(NOE)
t h(NE_NOE)
FMC_NOE
FMC_NWE
tv(A_NE)
FMC_A[25:0]
t h(A_NOE)
Address
tv(BL_NE)
t h(BL_NOE)
FMC_NBL[1:0]
t h(Data_NE)
t su(Data_NOE)
th(Data_NOE)
t su(Data_NE)
Data
FMC_D[15:0]
t v(NADV_NE)
tw(NADV)
FMC_NADV
(1)
FMC_NWAIT
th(NE_NWAIT)
tsu(NWAIT_NE)
MS32753V1
1. Mode 2/B, C and D only. In Mode 1, FMC_NADV is not used.
DS13314 Rev 3
137/236
216
Electrical characteristics
STM32H733xG
Table 58. Asynchronous non-multiplexed SRAM/PSRAM/NOR read timings(1)
Symbol
Parameter
Min
tw(NE)
FMC_NE low time
3Tfmc_ker_ck–1
tv(NOE_NE)
FMC_NEx low to FMC_NOE low
0
0.5
tw(NOE)
FMC_NOE low time
2Tfmc_ker_ck –1
2Tfmc_ker_ck+1
th(NE_NOE)
FMC_NOE high to FMC_NE high
hold time
Tfmc_ker_ck
-
tv(A_NE)
FMC_NEx low to FMC_A valid
-
0.5
th(A_NOE)
Address hold time after
FMC_NOE high
2Tfmc_ker_ck
-
tsu(Data_NE)
Data to FMC_NEx high setup
time
Tfmc_ker_ck+14
-
tsu(Data_NOE)
Data to FMC_NOEx high setup
time
13
-
th(Data_NOE)
Data hold time after FMC_NOE
high
0
-
th(Data_NE)
Data hold time after FMC_NEx
high
0
-
-
4
-
Tfmc_ker_ck+1
tv(NADV_NE) FMC_NEx low to FMC_NADV low
tw(NADV)
FMC_NADV low time
Max
Unit
3Tfmc_ker_ck+1
ns
1. Guaranteed by characterization results.
Table 59. Asynchronous non-multiplexed SRAM/PSRAM/NOR read-NWAIT
timings(1)(2)
Symbol
Parameter
Min
Max
tw(NE)
FMC_NE low time
7Tfmc_ker_ck–1
7Tfmc_ker_ck+1
tw(NOE)
FMC_NOE low time
5Tfmc_ker_ck–1
5Tfmc_ker_ck +1
tw(NWAIT)
FMC_NWAIT low time
Tfmc_ker_ck– 0.5
tsu(NWAIT_NE)
FMC_NWAIT valid before FMC_NEx
high
4Tfmc_ker_ck +9
-
th(NE_NWAIT)
FMC_NEx hold time after
FMC_NWAIT invalid
3Tfmc_ker_ck+12
-
1. Guaranteed by characterization results.
2. NWAIT pulse width is equal to 1 fmc_ker_ck cycle.
138/236
DS13314 Rev 3
Unit
ns
STM32H733xG
Electrical characteristics
Figure 20. Asynchronous non-multiplexed SRAM/PSRAM/NOR write waveforms
tw(NE)
FMC_NEx
FMC_NOE
tv(NWE_NE)
tw(NWE)
t h(NE_NWE)
FMC_NWE
tv(A_NE)
FMC_A[25:0]
th(A_NWE)
Address
tv(BL_NE)
FMC_NBL[1:0]
th(BL_NWE)
NBL
tv(Data_NE)
th(Data_NWE)
Data
FMC_D[15:0]
t v(NADV_NE)
FMC_NADV (1)
tw(NADV)
FMC_NWAIT
th(NE_NWAIT)
tsu(NWAIT_NE)
MS32754V1
1. Mode 2/B, C and D only. In Mode 1, FMC_NADV is not used.
DS13314 Rev 3
139/236
216
Electrical characteristics
STM32H733xG
Table 60. Asynchronous non-multiplexed SRAM/PSRAM/NOR write timings(1)
Symbol
Parameter
Min
Max
tw(NE)
FMC_NE low time
3Tfmc_ker_ck –1
3Tfmc_ker_ck + 1
tv(NWE_NE)
FMC_NEx low to FMC_NWE low
Tfmc_ker_ck–1
Tfmc_ker_ck
tw(NWE)
FMC_NWE low time
Tfmc_ker_ck –0.5
Tfmc_ker_ck+0.5
th(NE_NWE)
FMC_NWE high to FMC_NE high
hold time
Tfmc_ker_ck
-
tv(A_NE)
FMC_NEx low to FMC_A valid
-
1
th(A_NWE)
Address hold time after FMC_NWE
high
Tfmc_ker_ck –0.5
-
tv(BL_NE)
FMC_NEx low to FMC_BL valid
-
0.5
th(BL_NWE)
FMC_BL hold time after FMC_NWE
high
Tfmc_ker_ck –0.5
-
tv(Data_NE)
Data to FMC_NEx low to Data valid
-
Tfmc_ker_ck+ 2
th(Data_NWE)
Data hold time after FMC_NWE high
Tfmc_ker_ck
-
tv(NADV_NE)
FMC_NEx low to FMC_NADV low
-
5
tw(NADV)
FMC_NADV low time
-
Tfmc_ker_ck+ 1
Unit
ns
1. Guaranteed by characterization results.
Table 61. Asynchronous non-multiplexed SRAM/PSRAM/NOR write-NWAIT
timings(1)(2)
Symbol
Parameter
Min
Max
tw(NE)
FMC_NE low time
8Tfmc_ker_ck –1
8Tfmc_ker_ck+1
tw(NWE)
FMC_NWE low time
6Tfmc_ker_ck –1
6Tfmc_ker_ck+1
tsu(NWAIT_NE)
FMC_NWAIT valid before FMC_NEx
high
5Tfmc_ker_ck+13
-
th(NE_NWAIT)
FMC_NEx hold time after
FMC_NWAIT invalid
4Tfmc_ker_ck+12
-
1. Guaranteed by characterization results.
2. NWAIT pulse width is equal to 1 fmc_ker_ck cycle.
140/236
DS13314 Rev 3
Unit
ns
STM32H733xG
Electrical characteristics
Figure 21. Asynchronous multiplexed PSRAM/NOR read waveforms
tw(NE)
FMC_ NE
tv(NOE_NE)
t h(NE_NOE)
FMC_NOE
t w(NOE)
FMC_NWE
th(A_NOE)
tv(A_NE)
FMC_ A[25:16]
Address
tv(BL_NE)
th(BL_NOE)
FMC_ NBL[1:0]
NBL
th(Data_NE)
tsu(Data_NE)
t v(A_NE)
FMC_ AD[15:0]
tsu(Data_NOE)
th(Data_NOE)
Data
Address
th(AD_NADV)
t v(NADV_NE)
tw(NADV)
FMC_NADV
FMC_NWAIT
th(NE_NWAIT)
tsu(NWAIT_NE)
MS32755V1
DS13314 Rev 3
141/236
216
Electrical characteristics
STM32H733xG
Table 62. Asynchronous multiplexed PSRAM/NOR read timings(1)
Symbol
Parameter
Min
Max
tw(NE)
FMC_NE low time
4Tfmc_ker_ck –1
4Tfmc_ker_ck +1
tv(NOE_NE)
FMC_NEx low to FMC_NOE low
2Tfmc_ker_ck
2Tfmc_ker_ck
+0.5
ttw(NOE)
FMC_NOE low time
Tfmc_ker_ck –1
Tfmc_ker_ck+1
th(NE_NOE)
FMC_NOE high to FMC_NE high hold
time
Tfmc_ker_ck
-
tv(A_NE)
FMC_NEx low to FMC_A valid
-
0.5
tv(NADV_NE)
FMC_NEx low to FMC_NADV low
0
4.0
tw(NADV)
FMC_NADV low time
Tfmc_ker_ck –0.5
Tfmc_ker_ck +1
th(AD_NADV)
FMC_AD(address) valid hold time
after FMC_NADV high)
Tfmc_ker_ckk –4
-
th(A_NOE)
Address hold time after FMC_NOE
high
Tfmc_ker_ck –0.5
-
tsu(Data_NE)
Data to FMC_NEx high setup time
Tfmc_ker_ck +14
-
tsu(Data_NOE)
Data to FMC_NOE high setup time
13
-
th(Data_NE)
Data hold time after FMC_NEx high
0
-
th(Data_NOE)
Data hold time after FMC_NOE high
0
-
Unit
ns
1. Guaranteed by characterization results.
Table 63. Asynchronous multiplexed PSRAM/NOR read-NWAIT timings(1)
Symbol
Parameter
Min
Max
tw(NE)
FMC_NE low time
8Tfmc_ker_ck –1
8Tfmc_ker_ck +1
tw(NOE)
FMC_NWE low time
5Tfmc_ker_ck –1
5Tfmc_ker_ck +1
tsu(NWAIT_NE)
FMC_NWAIT valid before
FMC_NEx high
4Tfmc_ker_ck +9
-
th(NE_NWAIT)
FMC_NEx hold time after
FMC_NWAIT invalid
3Tfmc_ker_ck +12
-
1. Guaranteed by characterization results.
142/236
DS13314 Rev 3
Unit
ns
STM32H733xG
Electrical characteristics
Table 64. Asynchronous multiplexed PSRAM/NOR write timings(1)
Symbol
Parameter
Min
Max
tw(NE)
FMC_NE low time
4Tfmc_ker_ck –1
4Tfmc_ker_ck
tv(NWE_NE)
FMC_NEx low to FMC_NWE low
Tfmc_ker_ck –1
Tfmc_ker_ck +0.5
tw(NWE)
FMC_NWE low time
2Tfmc_ker_ck –0.5
2Tfmc_ker_ck +0.5
th(NE_NWE)
FMC_NWE high to FMC_NE high hold
time
Tfmc_ker_ck –0.5
-
tv(A_NE)
FMC_NEx low to FMC_A valid
-
1
tv(NADV_NE)
FMC_NEx low to FMC_NADV low
0
5.0
tw(NADV)
FMC_NADV low time
Tfmc_ker_ck –0.5
Tfmc_ker_ck + 1
th(AD_NADV)
FMC_AD(adress) valid hold time after
FMC_NADV high)
Tfmc_ker_ck –4.5
-
th(A_NWE)
Address hold time after FMC_NWE
high
Tfmc_ker_ck – 0.5
-
th(BL_NWE)
FMC_BL hold time after FMC_NWE
high
Tfmc_ker_ck – 0.5
-
tv(BL_NE)
FMC_NEx low to FMC_BL valid
-
0.5
tv(Data_NADV)
FMC_NADV high to Data valid
-
Tfmc_ker_ck +2
th(Data_NWE)
Data hold time after FMC_NWE high
Tfmc_ker_ck
-
Unit
ns
1. Guaranteed by characterization results.
Table 65. Asynchronous multiplexed PSRAM/NOR write-NWAIT timings(1)(2)
Symbol
Parameter
Min
Max
tw(NE)
FMC_NE low time
9Tfmc_ker_ck –1
9Tfmc_ker_ck
tw(NWE)
FMC_NWE low time
7Tfmc_ker_ck –0.5
7Tfmc_ker_ck +0.5
tsu(NWAIT_NE)
FMC_NWAIT valid before FMC_NEx
high
5Tfmc_ker_ck +9
-
th(NE_NWAIT)
FMC_NEx hold time after
FMC_NWAIT invalid
4Tfmc_ker_ck +12
-
Unit
ns
1. Guaranteed by characterization results.
2. NWAIT pulse width is equal to 1 fmc_ker_ck cycle.
DS13314 Rev 3
143/236
216
Electrical characteristics
STM32H733xG
Synchronous waveforms and timings
Figure 22 through Figure 25 represent synchronous waveforms and Table 66 through
Table 69 provide the corresponding timings. The results shown in these tables are obtained
with the following FMC configuration:
•
BurstAccessMode = FMC_BurstAccessMode_Enable
•
MemoryType = FMC_MemoryType_CRAM
•
WriteBurst = FMC_WriteBurst_Enable
•
CLKDivision = 1
•
DataLatency = 1 for NOR Flash, DataLatency = 0 for PSRAM, CL = 30 pF
In all the timing tables, the Tfmc_ker_ck is the fmc_ker_ck clock period, with the following
FMC_CLK maximum values:
•
For 2.7 V<VDD<3.6 V: maximum FMC_CLK = 137 MHz at CL = 20 pF
•
For 1.8 V<VDD<1.9 V: maximum FMC_CLK = 100 MHz at CL = 20 pF
•
For 1.62 V<VDD<1.8 V: maximumFMC_CLK = 88 MHz at CL = 15 pF
Figure 22. Synchronous multiplexed NOR/PSRAM read timings
BUSTURN = 0
tw(CLK)
tw(CLK)
FMC_CLK
Data latency = 0
td(CLKL-NExL)
FMC_NEx
t d(CLKL-NADVL)
td(CLKH-NExH)
td(CLKL-NADVH)
FMC_NADV
td(CLKL-AV)
td(CLKH-AIV)
FMC_A[25:16]
td(CLKL-NOEL)
td(CLKH-NOEH)
FMC_NOE
t d(CLKL-ADV)
FMC_AD[15:0]
td(CLKL-ADIV)
tsu(ADV-CLKH)
AD[15:0]
th(CLKH-ADV)
tsu(ADV-CLKH)
D1
tsu(NWAITV-CLKH)
FMC_NWAIT
(WAITCFG = 1b,
WAITPOL + 0b)
FMC_NWAIT
(WAITCFG = 0b,
WAITPOL + 0b)
tsu(NWAITV-CLKH)
tsu(NWAITV-CLKH)
th(CLKH-ADV)
D2
th(CLKH-NWAITV)
th(CLKH-NWAITV)
th(CLKH-NWAITV)
MS32757V1
144/236
DS13314 Rev 3
STM32H733xG
Electrical characteristics
Table 66. Synchronous multiplexed NOR/PSRAM read timings(1)
Symbol
Parameter
Min
Max
tw(CLK)
FMC_CLK period
2Tfmc_ker_ck –0.5
-
td(CLKL-NExL)
FMC_CLK low to FMC_NEx low (x=0..2)
-
3
td(CLKH_NExH)
FMC_CLK high to FMC_NEx high (x= 0…2)
Tfmc_ker_ck+1.5
-
td(CLKL-NADVL)
FMC_CLK low to
FMC_NADV low
1.62 V <VDD < 3.6 V
td(CLKL-NADVH)
FMC_CLK low to
FMC_NADV high
1.62 V <VDD < 3.6 V
2.7 V <VDD < 3.6 V
2.7 V <VDD < 3.6 V
-
1
5.5
2
-
td(CLKL-AV)
FMC_CLK low to FMC_Ax valid (x=16…25)
-
3
td(CLKH-AIV)
FMC_CLK high to FMC_Ax invalid (x=16…25)
Tfmc_ker_ck
-
td(CLKL-NOEL)
FMC_CLK low to FMC_NOE low
-
2.5
td(CLKH-NOEH)
FMC_CLK high to FMC_NOE high
Tfmc_ker_ck +1
-
td(CLKL-ADV)
FMC_CLK low to FMC_AD[15:0] valid
-
3
td(CLKL-ADIV)
FMC_CLK low to FMC_AD[15:0] invalid
0
-
tsu(ADV-CLKH)
FMC_A/D[15:0] valid data before FMC_CLK high
3
-
th(CLKH-ADV)
FMC_A/D[15:0] valid data after FMC_CLK high
0
-
tsu(NWAIT-
FMC_NWAIT valid before FMC_CLK high
3
-
FMC_NWAIT valid after FMC_CLK high
2.5
-
CLKH)
th(CLKH-NWAIT)
Unit
ns
1. Guaranteed by characterization results.
DS13314 Rev 3
145/236
216
Electrical characteristics
STM32H733xG
Figure 23. Synchronous multiplexed PSRAM write timings
BUSTURN = 0
tw(CLK)
tw(CLK)
FMC_CLK
Data latency = 0
td(CLKL-NExL)
td(CLKH-NExH)
FMC_NEx
td(CLKL-NADVL)
td(CLKL-NADVH)
FMC_NADV
td(CLKH-AIV)
td(CLKL-AV)
FMC_A[25:16]
td(CLKH-NWEH)
td(CLKL-NWEL)
FMC_NWE
td(CLKL-ADIV)
td(CLKL-ADV)
FMC_AD[15:0]
td(CLKL-Data)
td(CLKL-Data)
AD[15:0]
D1
D2
FMC_NWAIT
(WAITCFG = 0b,
WAITPOL + 0b)
tsu(NWAITV-CLKH)
th(CLKH-NWAITV)
td(CLKH-NBLH)
FMC_NBL
MS32758V1
146/236
DS13314 Rev 3
STM32H733xG
Electrical characteristics
Table 67. Synchronous multiplexed PSRAM write timings(1)
Symbol
Parameter
Min
Max
tw(CLK)
FMC_CLK period, VDD = 2.7 to 3.6 V
2Tfmc_ker_ck –0.5
-
td(CLKL-NExL)
FMC_CLK low to FMC_NEx low (x =0..2)
-
3
td(CLKH-NExH)
FMC_CLK high to FMC_NEx high
(x = 0…2)
Tfmc_ker_ck +1.5
-
td(CLKL-NADVL)
FMC_CLK low to
FMC_NADV low
1.62 V <VDD < 3.6 V
td(CLKL-NADVH)
FMC_CLK low to
FMC_NADV high
1.62 V <VDD < 3.6 V
2.7 V <VDD < 3.6 V
2.7 V <VDD < 3.6 V
-
1
Unit
5.5
2.0
-
td(CLKL-AV)
FMC_CLK low to FMC_Ax valid (x =16…25)
-
3
td(CLKH-AIV)
FMC_CLK high to FMC_Ax invalid (x =16…25)
Tfmc_ker_ck
-
td(CLKL-NWEL)
FMC_CLK low to FMC_NWE low
-
2.5
t(CLKH-NWEH)
FMC_CLK high to FMC_NWE high
Tfmc_ker_ck +1
-
td(CLKL-ADV)
FMC_CLK low to to FMC_AD[15:0] valid
-
2.5
td(CLKL-ADIV)
FMC_CLK low to FMC_AD[15:0] invalid
0
-
td(CLKL-DATA)
FMC_A/D[15:0] valid data after FMC_CLK low
-
3.5
td(CLKL-NBLL)
FMC_CLK low to FMC_NBL low
-
2
td(CLKH-NBLH)
FMC_CLK high to FMC_NBL high
Tfmc_ker_ck +0.5
-
tsu(NWAIT-CLKH)
FMC_NWAIT valid before FMC_CLK high
3
-
th(CLKH-NWAIT)
FMC_NWAIT valid after FMC_CLK high
2.5
-
ns
1. Guaranteed by characterization results.
DS13314 Rev 3
147/236
216
Electrical characteristics
STM32H733xG
Figure 24. Synchronous non-multiplexed NOR/PSRAM read timings
tw(CLK)
tw(CLK)
FMC_CLK
td(CLKL-NExL)
td(CLKH-NExH)
Data latency = 0
FMC_NEx
td(CLKL-NADVL)
td(CLKL-NADVH)
FMC_NADV
td(CLKH-AIV)
td(CLKL-AV)
FMC_A[25:0]
td(CLKL-NOEL)
td(CLKH-NOEH)
FMC_NOE
tsu(DV-CLKH)
th(CLKH-DV)
tsu(DV-CLKH)
FMC_D[15:0]
FMC_NWAIT
(WAITCFG = 1b,
WAITPOL + 0b)
FMC_NWAIT
(WAITCFG = 0b,
WAITPOL + 0b)
D1
tsu(NWAITV-CLKH)
tsu(NWAITV-CLKH)
tsu(NWAITV-CLKH)
th(CLKH-DV)
D2
th(CLKH-NWAITV)
t h(CLKH-NWAITV)
th(CLKH-NWAITV)
MS32759V1
148/236
DS13314 Rev 3
STM32H733xG
Electrical characteristics
Table 68. Synchronous non-multiplexed NOR/PSRAM read timings(1)
Symbol
Parameter
Min
Max
tw(CLK)
FMC_CLK period
2Tfmc_ker_ck –0.5
-
t(CLKL-NExL)
FMC_CLK low to FMC_NEx low (x=0..2)
-
3
td(CLKH-NExH)
FMC_CLK high to FMC_NEx high (x= 0…2)
Tfmc_ker_ck+1.5
-
td(CLKL-NADVL)
FMC_CLK low to
FMC_NADV low
1.62 V <VDD < 3.6 V
td(CLKL-NADVH)
FMC_CLK low to
FMC_NADV high
1.62 V <VDD < 3.6 V
2.7 V <VDD < 3.6 V
2.7 V <VDD < 3.6 V
-
1
Unit
5.5
2.0
-
td(CLKL-AV)
FMC_CLK low to FMC_Ax valid (x=16…25)
-
3
td(CLKH-AIV)
FMC_CLK high to FMC_Ax invalid (x=16…25)
Tfmc_ker_ck
-
td(CLKL-NOEL)
FMC_CLK ow to FMC_NOE low
-
2.5
td(CLKH-NOEH)
FMC_CLK high to FMC_NOE high
Tfmc_ker_ck+1
-
tsu(DV-CLKH)
FMC_D[15:0] valid data before FMC_CLK high
3
-
th(CLKH-DV)
FMC_D[15:0] valid data after FMC_CLK high
0
-
t(NWAIT-CLKH)
FMC_NWAIT valid before FMC_CLK high
3
-
th(CLKH-NWAIT)
FMC_NWAIT valid after FMC_CLK high
2.5
-
ns
1. Guaranteed by characterization results.
DS13314 Rev 3
149/236
216
Electrical characteristics
STM32H733xG
Figure 25. Synchronous non-multiplexed PSRAM write timings
tw(CLK)
tw(CLK)
FMC_CLK
td(CLKL-NExL)
td(CLKH-NExH)
Data latency = 0
FMC_NEx
td(CLKL-NADVL)
td(CLKL-NADVH)
FMC_NADV
td(CLKH-AIV)
td(CLKL-AV)
FMC_A[25:0]
td(CLKL-NWEL)
td(CLKH-NWEH)
FMC_NWE
td(CLKL-Data)
td(CLKL-Data)
D1
FMC_D[15:0]
D2
FMC_NWAIT
(WAITCFG = 0b, WAITPOL + 0b)
tsu(NWAITV-CLKH)
td(CLKH-NBLH)
th(CLKH-NWAITV)
FMC_NBL
MS32760V1
150/236
DS13314 Rev 3
STM32H733xG
Electrical characteristics
Table 69. Synchronous non-multiplexed PSRAM write timings(1)
Symbol
Parameter
Min
Max
t(CLK)
FMC_CLK period
2Tfmc_ker_ck –0.5
-
td(CLKL-NExL)
FMC_CLK low to FMC_NEx low (x=0..2)
-
3
t(CLKH-NExH)
FMC_CLK high to FMC_NEx high (x= 0…2)
Tfmc_ker_ck+1.5
-
td(CLKL-NADVL)
FMC_CLK low to
FMC_NADV low
1.62 V <VDD < 3.6 V
td(CLKL-NADVH)
FMC_CLK low to
FMC_NADV high
1.62 V <VDD < 3.6 V
2.7 V <VDD < 3.6 V
2.7 V <VDD < 3.6 V
-
1
5.5
2
-
td(CLKL-AV)
FMC_CLK low to FMC_Ax valid (x=16…25)
-
3
td(CLKH-AIV)
FMC_CLK high to FMC_Ax invalid (x=16…25)
Tfmc_ker_ck
-
td(CLKL-NWEL)
FMC_CLK low to FMC_NWE low
-
2.5
td(CLKH-NWEH)
FMC_CLK high to FMC_NWE high
Tfmc_ker_ck+1
-
td(CLKL-Data)
FMC_D[15:0] valid data after FMC_CLK low
-
3.5
td(CLKL-NBLL)
FMC_CLK low to FMC_NBL low
-
2
td(CLKH-NBLH)
FMC_CLK high to FMC_NBL high
Tfmc_ker_ck+0.5
-
tsu(NWAIT-
FMC_NWAIT valid before FMC_CLK high
3
-
FMC_NWAIT valid after FMC_CLK high
2.5
-
CLKH)
th(CLKH-NWAIT)
Unit
ns
1. Guaranteed by characterization results.
DS13314 Rev 3
151/236
216
Electrical characteristics
STM32H733xG
NAND controller waveforms and timings
Figure 26 through Figure 29 represent synchronous waveforms, and Table 70 and Table 71
provide the corresponding timings. The results shown in this table are obtained with the
following FMC configuration and a capacitive load (CL) of 30 pF:
•
COM.FMC_SetupTime = 0x01
•
COM.FMC_WaitSetupTime = 0x03
•
COM.FMC_HoldSetupTime = 0x02
•
COM.FMC_HiZSetupTime = 0x01
•
ATT.FMC_SetupTime = 0x01
•
ATT.FMC_WaitSetupTime = 0x03
•
ATT.FMC_HoldSetupTime = 0x02
•
ATT.FMC_HiZSetupTime = 0x01
•
Bank = FMC_Bank_NAND
•
MemoryDataWidth = FMC_MemoryDataWidth_16b
•
ECC = FMC_ECC_Enable
•
ECCPageSize = FMC_ECCPageSize_512Bytes
•
TCLRSetupTime = 0
•
TARSetupTime = 0
In all timing tables, the Tfmc_ker_ck is the fmc_ker_ck clock period.
Figure 26. NAND controller waveforms for read access
FMC_NCEx
ALE (FMC_A17)
CLE (FMC_A16)
FMC_NWE
td(ALE-NOE)
th(NOE-ALE)
FMC_NOE (NRE)
tsu(D-NOE)
th(NOE-D)
FMC_D[15:0]
MS32767V1
152/236
DS13314 Rev 3
STM32H733xG
Electrical characteristics
Figure 27. NAND controller waveforms for write access
FMC_NCEx
ALE (FMC_A17)
CLE (FMC_A16)
th(NWE-ALE)
td(ALE-NWE)
FMC_NWE
FMC_NOE (NRE)
th(NWE-D)
tv(NWE-D)
FMC_D[15:0]
MS32768V1
Figure 28. NAND controller waveforms for common memory read access
FMC_NCEx
ALE (FMC_A17)
CLE (FMC_A16)
th(NOE-ALE)
td(ALE-NOE)
FMC_NWE
tw(NOE)
FMC_NOE
tsu(D-NOE)
th(NOE-D)
FMC_D[15:0]
MS32769V1
DS13314 Rev 3
153/236
216
Electrical characteristics
STM32H733xG
Figure 29. NAND controller waveforms for common memory write access
FMC_NCEx
ALE (FMC_A17)
CLE (FMC_A16)
td(ALE-NOE)
tw(NWE)
th(NOE-ALE)
FMC_NWE
FMC_N OE
td(D-NWE)
tv(NWE-D)
th(NWE-D)
FMC_D[15:0]
MS32770V1
Table 70. Switching characteristics for NAND Flash read cycles(1)
Symbol
Parameter
Min
Max
tw(N0E)
FMC_NOE low width
4Tfmc_ker_ck – 0.5
4Tfmc_ker_ck+0.5
tsu(D-NOE)
FMC_D[15-0] valid data before
FMC_NOE high
11
-
th(NOE-D)
FMC_D[15-0] valid data after
FMC_NOE high
0
-
-
3Tfmc_ker_ck +0.5
4Tfmc_ker_ck –1
-
td(ALE-NOE) FMC_ALE valid before FMC_NOE low
th(NOE-ALE)
FMC_NWE high to FMC_ALE invalid
Unit
ns
1. Guaranteed by characterization results.
Table 71. Switching characteristics for NAND Flash write cycles(1)
Symbol
Parameter
Min
Max
tw(NWE)
FMC_NWE low width
4Tfmc_ker_ck – 0.5
4Tfmc_ker_ck +0.5
tv(NWE-D)
FMC_NWE low to FMC_D[15-0]
valid
0
-
th(NWE-D)
FMC_NWE high to FMC_D[15-0]
invalid
2Tfmc_ker_ck +1.5
-
td(D-NWE)
FMC_D[15-0] valid before
FMC_NWE high
5Tfmc_ker_ck – 5
-
td(ALE-NWE)
FMC_ALE valid before FMC_NWE
low
-
3Tfmc_ker_ck +0.5
th(NWE-ALE)
FMC_NWE high to FMC_ALE
invalid
2Tfmc_ker_ck – 0.5
-
1. Guaranteed by characterization results.
154/236
DS13314 Rev 3
Unit
ns
STM32H733xG
Electrical characteristics
SDRAM waveforms and timings
In all timing tables, the TKERCK is the fmc_ker_ck clock period, with the following
FMC_SDCLK maximum values:
•
For 2.7 V<VDD<3.6 V: maximum FMC_CLK = 95 MHz at 20 pF
•
For 1.8 V<VDD<1.9 V: maximum FMC_CLK = 90 MHz at 20 pF
•
For 1.62 V<DD<1.8 V: maximum FMC_CLK = 85 MHz at 15 pF
Figure 30. SDRAM read access waveforms (CL = 1)
FMC_SDCLK
td(SDCLKL_AddC)
th(SDCLKL_AddR)
td(SDCLKL_AddR)
FMC_A[12:0]
Row n
Col1
Col2
Coli
Coln
th(SDCLKL_AddC)
th(SDCLKL_SNDE)
td(SDCLKL_SNDE)
FMC_SDNE[1:0]
td(SDCLKL_NRAS)
th(SDCLKL_NRAS)
FMC_SDNRAS
th(SDCLKL_NCAS)
td(SDCLKL_NCAS)
FMC_SDNCAS
FMC_SDNWE
tsu(SDCLKH_Data)
FMC_D[31:0]
th(SDCLKH_Data)
Data1
Data2
Datai
Datan
MS32751V2
DS13314 Rev 3
155/236
216
Electrical characteristics
STM32H733xG
Table 72. SDRAM read timings(1)
Symbol
Parameter
Min
Max
tw(SDCLK)
FMC_SDCLK period
2Tfmc_ker_ck –
0.5
2Tfmc_ker_ck
+0.5
tsu(SDCLKH _Data)
Data input setup time
3
-
th(SDCLKH_Data)
Data input hold time
1.5
-
td(SDCLKL_Add)
Address valid time
-
2.0
td(SDCLKL- SDNE)
Chip select valid time
-
1.5(2)
th(SDCLKL_SDNE)
Chip select hold time
0
-
td(SDCLKL_SDNRAS)
SDNRAS valid time
-
1
th(SDCLKL_SDNRAS)
SDNRAS hold time
0
-
td(SDCLKL_SDNCAS)
SDNCAS valid time
-
2.0
th(SDCLKL_SDNCAS)
SDNCAS hold time
0.5
-
Unit
ns
1. Guaranteed by characterization results.
2. Using PC2_C I/O adds 4.5 ns to this timing.
Table 73. LPSDR SDRAM read timings(1)
Symbol
Parameter
Min
Max
tW(SDCLK)
FMC_SDCLK period
2Tfmc_ker_ck –
0.5
2Tfmc_ker_ck+0.5
tsu(SDCLKH_Data)
Data input setup time
3
-
th(SDCLKH_Data)
Data input hold time
2.5
-
td(SDCLKL_Add)
Address valid time
-
2
td(SDCLKL_SDNE)
Chip select valid time
-
1.5(2)(3)
th(SDCLKL_SDNE)
Chip select hold time
0
-
td(SDCLKL_SDNRAS
SDNRAS valid time
-
1
th(SDCLKL_SDNRAS)
SDNRAS hold time
0
-
td(SDCLKL_SDNCAS)
SDNCAS valid time
-
2
th(SDCLKL_SDNCAS)
SDNCAS hold time
0.5
-
1. Guaranteed by characterization results.
2. Using PC2 I/O adds 4 ns to this timing.
3. Using PC2_C I/O adds 16.5 ns to this timing.
156/236
DS13314 Rev 3
Unit
ns
STM32H733xG
Electrical characteristics
Figure 31. SDRAM write access waveforms
FMC_SDCLK
td(SDCLKL_AddC)
th(SDCLKL_AddR)
td(SDCLKL_AddR)
FMC_A[12:0]
Row n
Col1
Col2
Coli
Coln
th(SDCLKL_AddC)
th(SDCLKL_SNDE)
td(SDCLKL_SNDE)
FMC_SDNE[1:0]
th(SDCLKL_NRAS)
td(SDCLKL_NRAS)
FMC_SDNRAS
td(SDCLKL_NCAS)
th(SDCLKL_NCAS)
td(SDCLKL_NWE)
th(SDCLKL_NWE)
FMC_SDNCAS
FMC_SDNWE
td(SDCLKL_Data)
Data1
FMC_D[31:0]
Data2
Datai
Datan
th(SDCLKL_Data)
td(SDCLKL_NBL)
FMC_NBL[3:0]
MS32752V2
Table 74. SDRAM Write timings(1)
Symbol
Parameter
Min
Max
Unit
tw(SDCLK)
FMC_SDCLK period
2Tfmc_ker_ck – 0.5
2Tfmc_ker_ck+0.5
td(SDCLKL _Data)
Data output valid time
-
2
th(SDCLKL _Data)
Data output hold time
0.5
-
td(SDCLKL_Add)
Address valid time
-
2
td(SDCLKL_SDNWE)
SDNWE valid time
-
2
th(SDCLKL_SDNWE)
SDNWE hold time
0
-
td(SDCLKL_ SDNE)
Chip select valid time
-
1.5(2)
th(SDCLKL-_SDNE)
Chip select hold time
0
-
td(SDCLKL_SDNRAS)
SDNRAS valid time
-
1
th(SDCLKL_SDNRAS)
SDNRAS hold time
0
-
td(SDCLKL_SDNCAS)
SDNCAS valid time
-
2
td(SDCLKL_SDNCAS)
SDNCAS hold time
0.5
-
ns
1. Guaranteed by characterization results.
2. Using PC2_C I/O adds 4.5 ns to this timing.
DS13314 Rev 3
157/236
216
Electrical characteristics
STM32H733xG
Table 75. LPSDR SDRAM Write timings(1)
Symbol
Parameter
Min
Max
tw(SDCLK)
FMC_SDCLK period
td(SDCLKL _Data)
Data output valid time
-
2
th(SDCLKL _Data)
Data output hold time
0
-
td(SDCLKL_Add)
Address valid time
-
2.5
td(SDCLKL-SDNWE)
SDNWE valid time
-
2
th(SDCLKL-SDNWE)
SDNWE hold time
0
(2)(3)
Unit
2Tfmc_ker_ck – 0.5 2Tfmc_ker_ck+0.5
td(SDCLKL- SDNE)
Chip select valid time
-
th(SDCLKL- SDNE)
Chip select hold time
0
-
td(SDCLKL-SDNRAS)
SDNRAS valid time
-
1
th(SDCLKL-SDNRAS)
SDNRAS hold time
0
-
td(SDCLKL-SDNCAS)
SDNCAS valid time
-
2
td(SDCLKL-SDNCAS)
SDNCAS hold time
0.5
-
1.5
ns
1. Guaranteed by characterization results.
2. Using PC2 I/O adds 4 ns to this timing.
3. Using PC2_C I/O adds 16.5 ns to this timing.
6.3.19
Octo-SPI interface characteristics
Unless otherwise specified, the parameters given in Table 76 and Table 78 for OCTOSPI
are derived from tests performed under the ambient temperature, fHCLK frequency and VDD
supply voltage conditions summarized in Table 12: General operating conditions, with the
following configuration:
•
Output speed is set to OSPEEDRy[1:0] = 11
•
Measurement points are done at CMOS levels: 0.5VDD
•
IO Compensation cell activated.
•
HSLV activated when VDD ≤ 2.5 V
•
VOS level set to VOS0
Refer to Section 6.3.16: I/O port characteristics for more details on the input/output alternate
function characteristics.
Table 76. OCTOSPI characteristics in SDR mode(1)(2)
Symbol
F(CLK)
158/236
Parameter
OCTOSPI clock frequency
Conditions
Min
Typ
Max
1.71 V < VDD < 3.6 V,
VOS0,
CLOAD = 15 pF
-
-
92
1.71 V < VDD < 3.6 V,
VOS0, CLOAD =20 pF
-
-
90
2.7 V < VDD < 3.6 V,
VOS0,
CLOAD = 20 pF
-
-
140
DS13314 Rev 3
Unit
MHz
STM32H733xG
Electrical characteristics
Table 76. OCTOSPI characteristics in SDR mode(1)(2) (continued)
Symbol
tw(CKH)
tw(CKL)
tw(CKH)
tw(CKL)
ts(IN)(3)
th(IN)
(3)
Parameter
Conditions
OCTOSPI clock high and low PRESCALER[7:0] = n
time, even division
= 0,1,3,5
Min
Typ
Max
t(CK)/2
-
t(CK)/2+1
t(CK)/2–1
-
t(CK)/2
-
(n/2)*t(CK)/
(n+1)+1
-
(n/2+1)*t(CK)
/(n+1)
-
(n/2)*t(CK)/
(n+1)
OCTOSPI clock high and low PRESCALER[7:0] = n
time, odd division
= 2,4,6,8
(n/2+1)*t(CK)/
(n+1)–1
Data input setup time
-
3.0
-
Data input hold time
-
1.5
-
-
tv(OUT)
Data output valid time
-
-
0.5
1(4)
th(OUT)
Data output hold time
-
0
-
-
Unit
ns
1. All values apply to Octal and Quad-SPI mode.
2. Guaranteed by characterization results.
3. Delay block bypassed.
4. Using PC2 or PC3 I/O in the data bus adds 4 ns to this timing value.
Figure 32. OCTOSPI SDR read/write timing diagram
tr(CLK)
t(CLK)
tw(CLKH)
tw(CLKL)
tf(CLK)
Clock
tv(OUT)
Data output
th(OUT)
D0
D1
ts(IN)
Data input
D0
D2
th(IN)
D1
D2
MSv36878V3
DS13314 Rev 3
159/236
216
Electrical characteristics
STM32H733xG
Table 77. OCTOSPI characteristics in DTR mode (no DQS)(1)(2)
Symbol
FCK(3)
tw(CKH)
tw(CKL)
tw(CKH)
tw(CKL)
tsr(IN)
tsf(IN)(5)
thr(IN)
thf(IN)(5)
Parameter
OCTOSPI clock frequency
OCTOSPI clock high and
low time, even division
Conditions
Min
Typ
Max
1.71 V < VDD < 3.6 V,
VOS0, CLOAD = 15 pF
-
-
90(4)
1.71 V < VDD < 3.6 V,
VOS0, CLOAD = 20 pF
-
-
87(4)
2.7 V < VDD < 3.6 V,
VOS0, CLOAD = 20 pF
-
-
110
t(CK)/2
-
t(CK)/2+1
t(CK)/2–1
-
t(CK)/2
(n/2)*t(CK)/
(n+1)
-
(n/2)*t(CK)/
(n+1)+1
(n/2+1)*t(CK)/(
n+1) – 1
-
(n/2+1)*
t(CK)/(n+1)
3.0
-
-
PRESCALER[7:0] = n
= 0,1,3,5
OCTOSPI clock high and
low time, odd division
PRESCALER[7:0] = n
= 2,4,6,8
Data input setup time
-
Unit
MHz
ns
Data input hold time
tvr(OUT)
tvf(OUT)
Data output valid time
thr(OUT)
thf(OUT)
Data output hold time
-
1.50
-
-
DHQC = 0
-
6
7(6)
DHQC = 1,
Prescaler = 1,2 ...
-
tpclk/4+
1
tpclk/4+1.25
DHQC = 0
4.5
-
-
DHQC = 1,
Prescaler = 1,2 ...
tpclk/4
-
-
(6)
1. All values apply to Octal and Quad-SPI mode.
2. Guaranteed by characterization results.
3. DHQC must be set to reach the mentioned frequency.
4. Using PC2 or PC3 I/O in the data bus decreases the frequency to 47 MHz.
5. Delay block bypassed.
6. Using PC2 or PC3 I/O in the data bus adds 4 ns to this timing value.
Figure 33. OCTOSPI DTR mode timing diagram
tr(CLK)
t(CLK)
tw(CLKH)
tw(CLKL)
tf(CLK)
Clock
tvf(OUT)
Data output
thr(OUT)
D0
tvr(OUT)
D1
D2
thf(OUT)
D3
tsf(IN) thf(IN)
Data input
D0
D1
D4
D5
tsr(IN) thr(IN)
D2
D3
D4
D5
MSv36879V4
160/236
DS13314 Rev 3
STM32H733xG
Electrical characteristics
Table 78. OCTOSPI characteristics in DTR mode (with DQS)/Octal and Hyperbus(1)
Symbol
FCK(2)(3)
tw(CKH)
tw(CKL)
tw(CKH)
tw(CKL)
Parameter
OCTOSPI clock frequency
OCTOSPI clock high and
low time, even division
OCTOSPI clock high and
low time, odd division
Conditions
Min
Typ
Max
2,7 V < VDD < 3.6 V,
VOS0, CLOAD = 20 pF
-
-
100
1.71 V < VDD < 3.6 V,
VOS0, CLOAD = 20 pF
-
-
100(4)
t(CK)/2
-
t(CK)/2+1
t(CK)/2–1
-
t(CK)/2
(n/2)*t(CK)/
(n+1)
-
(n/2)*t(CK)/
(n+1)+1
(n/2+1)*t(CK)/(
n+1)–1
-
(n/2+1)*t(CK)/
(n+1)
PRESCALER[7:0] = n =
0,1,3,5
PRESCALER[7:0] = n =
2,4,6,8
MHz
tv(CK)
Clock valid time
-
-
-
t(CK)+1
th(CK)
Clock hold time
-
t(CK)/2
-
-
VODr(CK)
CK,CK crossing level on CK
rising edge
VDD = 1.8 V
922
-
1229
VODf(CK)
CK,CK crossing level on CK
falling edge
VDD = 1.8 V
1000
-
1277
tw(CS)
Chip select high time
-
3*t(CK)
-
-
tv(DQ)
Data input vallid time
-
0
-
-
tv(DS)
Data strobe input valid time
-
0
-
-
th(DS)
Data strobe input hold time
-
0
-
-
tv(RWDS)
Data strobe output valid
time
-
-
-
3 x t(CK)
Rising edge
0
-
-
Falling edge
0
-
-
Rising edge
1
-
-
Falling edge
1
-
(5)
tsr(DQ)
tsf(DQ)
thr(DQ)
thf(DQ)
tvr(OUT)
tvf(OUT)
Data input setup time
Data input hold time
Data output valid time rising
edge
Data output valid time
falling edge
thr(OUT)
Data output hold time rising
edge
thf(OUT)
Data output hold time falling
edge
Unit
ns
ns
mV
DHQC = 0
-
6
7
DHQC = 1,
Prescaler = 1,2...
-
tpclk/4+
1
tpclk/4+1.25
DHQC = 0
-
5.5
6(5)
DHQC = 1,
Prescaler = 1,2...
-
tpclk/4+
0.5
tpclk/4+0.75
DHQC = 0
4.5
-
-
DHQC = 1,
Prescaler = 1,2...
tpclk/4
-
-
DHQC = 0
4.5
-
-
DHQC = 1,
Prescaler = 1,2...
tpclk/4
-
-
ns
(5)
(5)
1. Guaranteed by characterization results.
DS13314 Rev 3
161/236
216
Electrical characteristics
STM32H733xG
2. Maximum frequency values are given for a RWDS to DQ skew of maximum +/-1.0 ns.
3. Activating DHQC is mandatory to reach this frequency
4. Using PC2 or PC3 I/O on data bus decreases the frequency to 47 MHz.
5. Using PC2 or PC3 I/O on the data bus adds 4 ns to this timing value.
Figure 34. OCTOSPI Hyperbus clock timing diagram
tr(CLK)
tf(NCLK)
tw(CLKH)
tw(NCLKL)
t(CLK)
t(NCLK)
tw(CLKL)
tw(NCLKH)
tf(CLK)
tr(NCLK)
NCLK
VOD(CLK)
CLK
MSv47732V3
Figure 35. OCTOSPI Hyperbus read timing diagram
tw(CS)
NCS
tv(CLK)
th(CLK)
t ACC= Initial access
CLK, NCLK
tv(RWDS)
tv(DS)
th(DS)
RWDS
tv(OUT)
DQ[7:0]
47:40 39:32
th(OUT)
31:24
23:16
Latency count
15:8
7:0
Command address
Host drives DQ[7:0] and the memory drives RWDS.
162/236
DS13314 Rev 3
tv(DQ) ts(DQ)
th(DQ)
Dn
A
Dn+1
A
Dn
B
Dn+1
B
Memory drives DQ[7:0] and RWDS.
MSv47733V3
STM32H733xG
Electrical characteristics
Figure 36. OCTOSPI Hyperbus write timing diagram
tw(CS)
NCS
Read write recovery
Access latency
tv(CLK)
th(CLK)
CLK, NCLK
tv(RWDS) High = 2x latency count
RWDS
tv(OUT)
th(OUT)
tv(OUT)
th(OUT)
Low = 1x latency count
Latency count
DQ[7:0]
tv(OUT)
th(OUT)
47:40
31:24
39:32
23:16
15:8
Dn
A
7:0
Command address
Dn
B
Dn+1
A
Dn+1
B
Host drives DQ[7:0] and RWDS.
Host drives DQ[7:0] and the memory drives RWDS.
MSv47734V3
6.3.20
Delay block (DLYB) characteristics
Unless otherwise specified, the parameters given in Table 79 for Delay Block are derived
from tests performed under the ambient temperature, frcc_c_ck frequency and VDD supply
voltage summarized in Table 12: General operating conditions, with the following
configuration:
Table 79. Delay Block characteristics
6.3.21
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
tinit
Initial delay
-
900
1300
1900
ps
t∆
Unit Delay
-
28
33
41
-
16-bit ADC characteristics
Unless otherwise specified, the parameters given in Table 80, Table 81 and Table 82 are
derived from tests performed under the ambient temperature, fPCLK2 frequency and VDDA
supply voltage conditions summarized in Table 12: General operating conditions.
Table 80. 16-bit ADC characteristics(1)(2)
Symbol
Parameter
Conditions
Min
Typ
Max
VDDA
Analog supply
voltage for ADC
ON
-
1.62
-
3.6
VREF+
Positive
reference voltage
VDDA ≥ 2 V
1.62
-
VDDA
VREF-
Negative
reference voltage
VDDA < 2 V
VDDA
-
VSSA
DS13314 Rev 3
Unit
V
163/236
216
Electrical characteristics
STM32H733xG
Table 80. 16-bit ADC characteristics(1)(2) (continued)
Symbol
fADC
Parameter
ADC clock
frequency
Conditions
0.12
-
50
0.12
-
25
BOOST = 01
0.12
-
12.5
BOOST = 00
-
-
6.25
fADC = 36 MHz
SMP = 1.5
-
-
3.60
Resolution = 16 bits
fADC = 37 MHz
SMP = 2.5
-
-
3.35
Resolution = 14 bits
fADC = 50 MHz
SMP = 2.5
-
-
5.00
fADC = 50 MHz
SMP = 2.5
-
-
5.50
1.62 V ≤ VDDA ≤ 3.6 V
TJ = 90 °C
TJ = 125 °C
fADC = 50 MHz
SMP = 1.5
-
-
7.10
Resolution = 8 bits
fADC = 50 MHz
SMP = 1.5
-
-
8.30
Resolution = 14 bits
fADC = 49 MHz
SMP = 1.5
-
-
4.90
fADC = 50 MHz
SMP = 1.5
-
-
5.50
Resolution = 10 bits
Resolution = 12 bits
TJ = 140 °C
fADC = 50 MHz
SMP = 1.5
-
-
6.70
fADC = 50 MHz
SMP = 1.5
-
-
8.30
fADC = 32 MHz
SMP = 2.5
-
-
2.90
Resolution = 16 bits
fADC = 31 MHz
SMP = 2.5
-
-
2.80
Resolution = 14 bits
fADC = 33 MHz
SMP = 2.5
-
-
3.30
Resolution = 12 bits
fADC = 39 MHz
SMP = 2.5
-
-
4.30
fADC = 48 MHz
SMP = 2.5
-
-
6.00
fADC = 50 MHz
SMP = 2.5
-
-
7.10
fADC = 37 MHz
SMP = 2.5
-
-
4.10
fADC = 46 MHz
SMP = 2.5
-
-
5.70
fADC = 50 MHz
SMP = 2.5
-
-
7.10
-
-
resolution = 14 bits
-
-
resolution = 12 bits
-
-
-
-
-
-
-
-
-
-
-
-
Resolution = 10 bits
Resolution = 8 bits
Resolution = 16 bits,
VDDA >2.5 V
Sampling rate for
Fast channels
Resolution = 10 bits
TJ = 90 °C
TJ = 125 °C
Resolution = 8 bits
Resolution = 12 bits
Resolution = 10 bits
TJ = 140 °C
Resolution = 8 bits
Resolution = 16 bits
Sampling rate for
Slow channels(4)
Max
BOOST = 11
Resolution = 12 bits
fs(3)
Typ
BOOST = 10
Resolution = 16 bits,
VDDA >2.5 V
Sampling rate for
Direct channels
Min
resolution = 10 bits
TJ = 90 °C
TJ = 125 °C
resolution = 8 bits
resolution = 12 bits
resolution = 10 bits
TJ = 140 °C
resolution = 8 bits
Unit
MHz
MSps
1.00
tTRIG
External trigger
period
Resolution = 16 bits
-
-
10
1/
fADC
VAIN(5)
Conversion
voltage range
-
0
-
VREF+
V
VCMIV
Common mode
input voltage
-
VREF/2
− 10%
VREF/
2
VREF/2
+ 10%
V
164/236
DS13314 Rev 3
STM32H733xG
Electrical characteristics
Table 80. 16-bit ADC characteristics(1)(2) (continued)
Symbol
RAIN(6)
Parameter
External input
impedance
Conditions
Min
Typ
Max
Unit
Resolution = 16 bits, TJ = 125 °C
-
-
-
-
170
Resolution = 14 bits, TJ = 125 °C
-
-
-
-
435
Resolution = 12 bits, TJ =125 °C
-
-
-
-
1,150
Resolution = 10 bits, TJ = 125 °C
-
-
-
-
5,650
Resolution = 8 bits, TJ = 125 °C
-
-
-
-
26,500
Ω
CADC
Internal sample
and hold
capacitor
-
-
4
-
pF
tADCVREG
_STUP
ADC LDO startup
time
-
-
5
10
us
tSTAB
ADC Power-up
time
LDO already started
1
-
-
conver
sion
cycle
tCAL
Offset and
linearity
calibration time
-
16,5010
1/fADC
tOFF_
Offset calibration
time
-
1,280
1/fADC
CAL
tLATR
tLATRINJ
Trigger
conversion
latency regular
and injected
channels without
conversion abort
Trigger
conversion
latency regular
injected channels
aborting a regular
conversion
CKMODE = 00
1.5
2
2.5
CKMODE = 01
-
-
2.5
CKMODE = 10
-
-
2.5
CKMODE = 11
-
-
2.25
CKMODE = 00
2.5
3
3.5
CKMODE = 01
-
-
3.5
CKMODE = 10
-
-
3.5
CKMODE = 11
-
-
3.25
1/fADC
1/fADC
tS
Sampling time
-
1.5
-
810.5
1/fADC
tCONV
Total conversion
time (including
sampling time)
Resolution = N bits
ts + 0.5
+ N/2
-
-
1/fADC
DS13314 Rev 3
165/236
216
Electrical characteristics
STM32H733xG
Table 80. 16-bit ADC characteristics(1)(2) (continued)
Symbol
IDDA_D
(ADC)
Parameter
(ADC)
IDD
(ADC)
Min
Typ
Max
ADC
consumption on
VDDA,
BOOST=11,
Differential mode
Resolution = 16 bits, fADC = 25 MHz
-
-
-
1,440
-
Resolution = 14 bits, fADC = 30 MHz
-
-
-
1,350
-
Resolution = 12 bits, fADC = 40 MHz
-
-
-
990
-
ADC
consumption on
VDDA,
BOOST=10,
Differential mode,
fADC = 25 MHz
Resolution = 16 bits
-
-
-
1,080
-
Resolution = 14 bits
-
-
-
810
-
Resolution = 12 bits
-
-
-
585
-
ADC
consumption on
VDDA,
BOOST=01,
Differential mode,
fADC = 12.5 MHz
Resolution = 16 bits
-
-
-
630
-
Resolution = 14 bits
-
-
-
432
-
Resolution = 12 bits
-
-
-
315
-
ADC
consumption on
VDDA,
BOOST=00,
Differential mode,
fADC = 6.25 MHz
Resolution = 16 bits
-
-
-
360
-
Resolution = 14 bits
-
-
-
270
-
Resolution = 12 bits
-
-
-
225
-
ADC
consumption on
VDDA,
BOOST=11,
Single-ended
mode
IDDA_SE
Conditions
Resolution = 16 bits, fADC=25 MHz
-
-
-
720
-
Resolution = 14 bits, fADC=30 MHz
-
-
-
675
-
Resolution = 12 bits, fADC=40 MHz
-
-
-
495
-
ADC
consumption on
VDDA,
BOOST=10,
Singl-ended
mode,
fADC = 25 MHz
Resolution = 16 bits
-
-
-
540
-
Resolution = 14 bits
-
-
-
405
-
Resolution = 12 bits
-
-
-
292.5
-
ADC
consumption on
VDDA,
BOOST=01,
Single-ended
mode,
fADC = 12.5 MHz
Resolution = 16 bits
-
-
-
315
-
Resolution = 14 bits
-
-
-
216
-
Resolution = 12 bits
-
-
-
157.5
-
ADC
consumption on
VDDA
BOOST=00,
Single-ended
mode
fADC=6.25 MHz
Resolution = 16 bits
-
-
-
180
-
Resolution = 14 bits
-
-
-
135
-
Resolution = 12 bits
-
-
-
112.5
-
ADC
consumption on
VDD
Unit
µA
fADC=50 MHz
-
-
-
400
-
fADC=25 MHz
-
-
-
220
-
fADC=12.5 MHz
-
-
-
180
-
fADC=6.25 MHz
-
-
-
120
-
fADC=3.125 MHz
-
-
-
80
-
1. Guaranteed by design.
2. The voltage booster on ADC switches must be used for VDDA < 2.4 V (embedded I/O switches).
3.
These values are valid for TFBGA100, UFBGA169 and UFBGA176+25 packages and one ADC. The values for other packages and multiple
ADCs may be different.
4.
For slow channels, the performance should be limited to 1 Msps what ever the value of fADC.
166/236
DS13314 Rev 3
STM32H733xG
Electrical characteristics
5.
Depending on the package, VREF+ can be internally connected to VDDA and VREF- to VSSA.
6.
The tolerance is 10 LSBs for 16-bit resolution, 4 LSBs for 14-bit resolution, and 2 LSBs for 12-bit, 10-bit and 8-bit resolutions.
Table 81. Minimum sampling time vs RAIN (16-bit ADC)(1)(2)
Minimum sampling time (s)
Resolution
RAIN (Ω)
Direct
channels(3)
16 bits
47
7.37E-08
1.14E-07
1.72E-07
47
6.29E-08
9.74E-08
1.55E-07
68
6.84E-08
1.02E-07
1.58E-07
100
7.80E-08
1.12E-07
1.62E-07
150
9.86E-08
1.32E-07
1.80E-07
220
1.32E-07
1.61E-07
2.01E-07
47
5.32E-08
8.00E-08
1.29E-07
68
5.74E-08
8.50E-08
1.32E-07
100
6.58E-08
9.31E-08
1.40E-07
150
8.37E-08
1.10E-07
1.51E-07
220
1.11E-07
1.34E-07
1.73E-07
330
1.56E-07
1.78E-07
2.14E-07
470
2.16E-07
2.39E-07
2.68E-07
680
3.01E-07
3.29E-07
3.54E-07
47
4.34E-08
6.51E-08
1.08E-07
68
4.68E-08
6.89E-08
1.11E-07
100
5.35E-08
7.55E-08
1.16E-07
150
6.68E-08
8.77E-08
1.26E-07
220
8.80E-08
1.08E-07
1.40E-07
330
1.24E-07
1.43E-07
1.71E-07
470
1.69E-07
1.89E-07
2.13E-07
680
2.38E-07
2.60E-07
2.80E-07
1000
3.45E-07
3.66E-07
3.84E-07
1500
5.15E-07
5.35E-07
5.48E-07
2200
7.42E-07
7.75E-07
7.78E-07
3300
1.10E-06
1.14E-06
1.14E-06
14 bits
12 bits
10 bits
DS13314 Rev 3
Fast channels(4) Slow channels(5)
167/236
216
Electrical characteristics
STM32H733xG
Table 81. Minimum sampling time vs RAIN (16-bit ADC)(1)(2) (continued)
Minimum sampling time (s)
Resolution
8 bits
RAIN (Ω)
Direct
channels(3)
47
3.32E-08
5.10E-08
8.61E-08
68
3.59E-08
5.35E-08
8.83E-08
100
4.10E-08
5.83E-08
9.22E-08
150
5.06E-08
6.76E-08
9.95E-08
220
6.61E-08
8.22E-08
1.11E-07
330
9.17E-08
1.08E-07
1.32E-07
470
1.24E-07
1.40E-07
1.63E-07
680
1.74E-07
1.91E-07
2.12E-07
1000
2.53E-07
2.70E-07
2.85E-07
1500
3.73E-07
3.93E-07
4.05E-07
2200
5.39E-07
5.67E-07
5.75E-07
3300
8.02E-07
8.36E-07
8.38E-07
4700
1.13E-06
1.18E-06
1.18E-06
6800
1.62E-06
1.69E-06
1.68E-06
10000
2.36E-06
2.47E-06
2.45E-06
15000
3.50E-06
3.69E-06
3.65E-06
Fast channels(4) Slow channels(5)
1. Guaranteed by design.
2. Data valid at up to 130 °C, with a 47 pF PCB capacitor, and VDDA=1.6 V.
3. Direct channels are connected to analog I/Os (PA0_C, PA1_C, PC2_C and PC3_C) to optimize ADC performance.
4. Fast channels correspond to PA6, PB1, PC4, PF11, PF13 for ADCx_INPx, and to PA7, PB0, PC5, PF12, PF14 for
ADCx_INNx.
5. Slow channels correspond to all ADC inputs except for the Direct and Fast channels.
168/236
DS13314 Rev 3
STM32H733xG
Electrical characteristics
Table 82. 16-bit ADC accuracy(1)(2)
Symbol
Parameter
Conditions(3)
Direct
channel
ET
Total undadjusted error
Fast channel
Slow
channel
Min
Typ
Max
Single ended
-
+10/–20
-
Differential
-
±15
-
Single ended
-
+10/–20
-
Differential
-
±15
-
Single ended
-
±10
-
±10
-
Differential
EO
Offset error
-
-
±10
-
EG
Gain error
-
-
±15
-
Single ended
-
+3/–1
-
Differential
-
+4.5/–1
-
Single ended
-
±11
-
Differential
-
±7
-
Single ended
-
±13
-
Differential
-
±7
-
Single ended
-
±10
-
Differential
-
±6
-
Single ended
-
12.2
-
Differential
-
13.2
-
Single ended
-
75.2
-
Differential
-
81.2
-
Single ended
-
77.0
-
Differential
-
81.0
-
Single ended
-
87
-
Differential
-
90
-
ED
Differential linearity error
Direct
channel
EL
Integral linearity error
Fast channel
Slow
channel
ENOB
Effective number of bits
SINAD
Signal-to-noise and
distortion ratio
SNR
Signal-to-noise ratio
THD
Total harmonic distortion
Unit
LSB
Bits
dB
1. Guaranteed by characterization results for BGA packages. The values for LQFP packages might differ.
2. ADC DC accuracy values are measured after internal calibration.
3. ADC clock frequency = 25 MHz, ADC resolution = 16 bits, VDDA=VREF+=3.3 V, BOOST=11 and 16-bit mode.
Note:
ADC accuracy vs. negative injection current: injecting a negative current on any analog
input pins should be avoided as this significantly reduces the accuracy of the conversion
being performed on another analog input. It is recommended to add a Schottky diode (pin to
ground) to analog pins which may potentially inject negative currents.
Any positive injection current within the limits specified for IINJ(PIN) and ΣIINJ(PIN) does not
affect the ADC accuracy.
DS13314 Rev 3
169/236
216
Electrical characteristics
STM32H733xG
Figure 37. ADC accuracy characteristics
VREF+
[1LSB =
2n
Output code
VDDA
(or
)]
2n
EG
(1) Example of an actual transfer curve
(2) Ideal transfer curve
(3) End-point correlation line
2n-1
2n-2
2n-3
(2)
(3)
ET
EL
EO
ED
(2n/2n)*VREF+
(2n-1/2n)*VREF+
(2n-2/2n)*VREF+
(2n-3/2n)*VREF+
(7/2n)*VREF+
(6/2n)*VREF+
(5/2n)*VREF+
(4/2n)*VREF+
(3/2n)*VREF+
1 LSB ideal
(2/2n)*VREF+
0
VSSA
(1)
(1/2n)*VREF+
7
6
5
4
3
2
1
n = ADC resolution
ET = total unadjusted error: maximum deviation
between the actual and ideal transfer curves
EO = offset error: maximum deviation between the first
actual transition and the first ideal one
EG = gain error: deviation between the last ideal
transition and the last actual one
ED = differential linearity error: maximum deviation
between actual steps and the ideal one
EL = integral linearity error: maximum deviation between
any actual transition and the end point correlation line
VREF+ (VDDA)
MSv19880V6
1. Example of an actual transfer curve.
2. Ideal transfer curve.
3. End point correlation line.
4. ET = Total Unadjusted Error: maximum deviation between the actual and the ideal transfer curves.
EO = Offset Error: deviation between the first actual transition and the first ideal one.
EG = Gain Error: deviation between the last ideal transition and the last actual one.
ED = Differential Linearity Error: maximum deviation between actual steps and the ideal one.
EL = Integral Linearity Error: maximum deviation between any actual transition and the end point
correlation line.
Figure 38. Typical connection diagram when using the ADC with FT/TT pins
featuring analog switch function
VREF+(4)
VDDA(4)
Sample-and-hold ADC converter
I/O
analog
switch
RAIN(1)
RADC
Converter
VAIN
Cparasitic(2)
Ilkg(3)
VSS
CADC
Sampling
switch with
multiplexing
VSS
VSSA
MSv67871V3
1. Refer to Table 80: 16-bit ADC characteristics for the values of RAIN, RADC and CADC.
2. Cparasitic represents the capacitance of the PCB (dependent on soldering and PCB layout quality) plus the
pad capacitance (refer to Table 51: I/O static characteristics). A high Cparasitic value downgrades
conversion accuracy. To remedy this, fADC should be reduced.
3. Refer to Table 51: I/O static characteristics for the value of Ilkg.
4. Refer to Figure 10: Power supply scheme.
170/236
DS13314 Rev 3
STM32H733xG
Electrical characteristics
General PCB design guidelines
Power supply decoupling should be performed as shown in Figure 39 or Figure 40,
depending on whether VREF+ is connected to VDDA or not. The 100 nF capacitors should be
ceramic (good quality). They should be placed them as close as possible to the chip.
Figure 39. Power supply and reference decoupling (VREF+ not connected to VDDA)
STM32
VREF+(1)
1 μF // 100 nF
VDDA
1 μF // 100 nF
VSSA/VREF-(1)
MSv50648V2
1. When VREF+ and VREF- inputs are not available, they are internally connected to VDDA and VSSA,
respectively.
Figure 40. Power supply and reference decoupling (VREF+ connected to VDDA)
STM32
VREF+/VDDA(1)
1 μF // 100 nF
VREF-/VSSA(1)
MSv50649V1
1. When VREF+ and VREF- inputs are not available, they are internally connected to VDDA and VSSA,
respectively.
DS13314 Rev 3
171/236
216
Electrical characteristics
6.3.22
STM32H733xG
12-bit ADC characteristics
Unless otherwise specified, the parameters given in Table 83, Table 84 and Table 85 are
derived from tests performed under the ambient temperature and VDDA supply voltage
conditions summarized in Table 12: General operating conditions. In Table 83, Table 84 and
Table 85, fADC refers to fadc_ker_ck.
Table 83. 12-bit ADC characteristics(1)(2)
Symbol
Parameter
Conditions
Min
Typ
Max
VDDA
Analog
power
supply for
ADC ON
-
1.62
-
3.6
VREF+
(3)
Positive
reference
voltage
VDDA ≥ VREF+
1.62
-
VDDA
VREF-
Negative
reference
voltage
-
VSSA
-
-
fADC
ADC clock
frequency
1,62 V ≤ VDDA ≤ 3.6 V
1.5
-
75
-
-
5
-
-
4
-
-
3.33
Resolution
= 12 bits
fADC = 75
MHz
Continuous
2.4 V ≤ VDDA ≤ 3.6 V
and
Discontinuous
1.6V ≤ VDDA≤ 3.6 V
mode(5)
–40 °C ≤ TJ ≤ 130 °C
Resolution
= 10 bits
fS(4)
fADC = 50
MHz(6)
1.6 V ≤ VDDA ≤ 3.6 V
fADC = 38
MHz(6)
-
-
2.53
1.6V ≤ VDDA ≤ 3.6V
fADC = 75
MHz
-
-
5.77
-
-
4.46
-
3.23
2.4 V ≤ VDDA ≤ 3.6 V
–40 °C ≤ TJ ≤ 130 °C
Single mode
Sampling
rate for
Direct
channels
Resolution
= 8 bits
Continuous
and
Discontinuous
mode(5)
-
1.6V ≤ VDDA ≤ 3.6V
fADC = 75
MHz
-
-
6.82
-
-
6.09
–40 °C ≤ TJ ≤ 130 °C
fADC = 67
MHz(6)
SMP
= 2.5
fADC = 48
MHz(6)
-
-
4.36
1.6V ≤ VDDA ≤ 3.6V
fADC = 75
MHz
-
-
8.33
-
-
8.33
-
-
6.11
2.4 V ≤ VDDA ≤ 3.6 V
–40 °C ≤ TJ ≤ 130 °C
1.6V ≤ VDDA ≤ 3.6V
DS13314 Rev 3
fADC = 75
MHz(6)
fADC = 55
MHz(6)
V
MHz
MSPS
1.6V ≤ VDDA ≤ 3.6V
Single mode
172/236
SMP
= 2.5
fADC = 42
MHz(6)
Single mode
Resolution
= 6 bits
fADC = 58
MHz(6)
1.6V ≤ VDDA ≤ 3.6V
2.4 V ≤ VDDA ≤ 3.6 V
Continuous
and
Discontinuous
mode(5)
SMP
= 2.5
2.4 V ≤ VDDA ≤ 3.6 V
Single mode
Continuous
and
Discontinuous
mode(5)
fADC = 60
MHz
Unit
SMP
= 2.5
STM32H733xG
Electrical characteristics
Table 83. 12-bit ADC characteristics(1)(2) (continued)
Symbol
Parameter
Conditions
Resolution
= 12 bits
fADC = 65
MHz
Continuous
2.4 V ≤ VDDA ≤ 3.6 V
and
Discontinuous
1.6V ≤ VDDA ≤ 3.6V
mode(5)
–40 °C ≤ TJ ≤ 130 °C
Resolution
= 10 bits
fS(4)
Resolution
= 8 bits
(continued)
-
-
2.13
fADC = 75
MHz
-
-
5.77
-
-
2.77
–40 °C ≤ TJ ≤ 130 °C
fADC = 36
MHz(6)
SMP
= 2.5
1.6V ≤ VDDA ≤ 3.6V
fADC = 30
MHz(6)
-
-
2.31
1.6V ≤ VDDA ≤ 3.6V
fADC = 75
MHz
-
-
6.82
-
-
4.00
–40 °C ≤ TJ ≤ 130 °C
fADC =44
MHz(6)
SMP
= 2.5
fADC = 35
MHz(6)
-
-
3.18
1.6V ≤ VDDA ≤ 3.6V
fADC = 75
MHz
-
-
8.33
-
-
6.22
-
-
4.66
-
-
1.00
-
-
1.28
-
-
1.63
-
-
2.08
–40 °C ≤ TJ ≤ 130 °C
fADC = 56
MHz(6)
SMP
= 2.5
fADC = 42
MHz(6)
–40 °C ≤ TJ ≤ 130 °C
-
Resolution
= 6 bits
fADC = 15
MHz(6)
SMP
= 2.5
tTRIG
External
trigger
period
Resolution = 12 bits
-
-
15
VAIN
Conversion
voltage
range
-
0
-
VREF+
VCMIV
Common
mode input
voltage
-
VREF
/2−
10%
VREF
/2
VREF/2
+ 10%
Resolution = 12 bits, TJ = 125 °C
-
-
220
RAIN
External
input
impedance
Resolution = 10 bits, TJ = 125 °C
-
-
2100
Resolution = 8 bits, TJ = 125 °C
-
-
12000
Resolution = 6 bits, TJ = 125 °C
-
-
80000
(7)
DS13314 Rev 3
Unit
MSPS
1.6V ≤ VDDA ≤ 3.6V
Resolution
= 12 bits
Resolution
= 8 bits
3.87
1.6V ≤ VDDA ≤ 3.6V
2.4 V ≤ VDDA ≤ 3.6 V
-
-
1.73
1.6V ≤ VDDA ≤ 3.6V
Resolution
= 10 bits
-
-
Single mode
Sampling
rate for slow
channels
4.33
-
Single mode
Resolution
= 6 bits
-
fADC =
26 MHz(6)
2.4 V ≤ VDDA ≤ 3.6 V
Continuous
and
Discontinuous
mode(5)
-
1.6V ≤ VDDA ≤ 3.6V
2.4 V ≤ VDDA ≤ 3.6 V
Continuous
and
Discontinuous
mode(5)
Max
fADC = 32
MHz(6)
Single mode
Sampling
rate for fast
channels
(VIN[0:5])
SMP
= 2.5
Typ
2.4 V ≤ VDDA ≤ 3.6 V
Single mode
Continuous
and
Discontinuous
mode(5)
fADC = 58
MHz
Min
1/fADC
V
Ω
173/236
216
Electrical characteristics
STM32H733xG
Table 83. 12-bit ADC characteristics(1)(2) (continued)
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
CADC
Internal
sample and
hold
capacitor
-
-
5
-
pF
ADC LDO
startup time
-
-
5
10
µs
tSTAB
ADC powerup time
LDO already started
1
-
-
conversion
cycle
tOFF_
Offset
calibration
time
-
135
-
-
Trigger
conversion
latency for
regular and
injected
channels
without
aborting the
conversion
CKMODE = 00
1.5
2
2.5
CKMODE = 01
-
-
2.5
CKMODE = 10
-
-
2.5
CKMODE = 11
-
-
2.25
Trigger
conversion
latency for
regular and
injected
channels
when a
regular
conversion
is aborted
CKMODE = 00
2.5
3
3.5
CKMODE = 01
-
-
3.5
CKMODE = 10
-
-
3.5
CKMODE = 11
-
-
3.25
tADCV
REG_
STUP
CAL
tLATR
tLATR
INJ
tS
Sampling
time
-
2.5
-
640.5
tCONV
Total
conversion
time
(including
sampling
time)
N-bits resolution
tS +
0.5 +
N
-
-
ADC
consumption
IDDA_ on VDDA and
VREF,
D(ADC)
Differential
mode
IDDA_
SE
(ADC)
IDD
(ADC)
ADC
consumption
on VDDA and
VREF,
Singleended mode
fS= 5 MSPS
-
430
-
fS = 1 MSPS
-
133
-
fS = 0.1 MSPS
-
51
-
fS= 5 MSPS
-
350
-
fS = 1 MSPS
-
122
-
fS = 0.1 MSPS
-
47
-
-
-
2.4
-
ADC
consumption
on VDD per
fADC
1. Guaranteed by design.
2. The voltage booster on ADC switches must be used for VDDA < 2.4 V (embedded I/O switches).
3.
Depending on the package, VREF+ can be internally connected to VDDA and VREF- to VSSA.
4.
Guaranteed by characterization for BGA and CSP packages. The values for LQFP packages may be different.
5.
The conversion of the first element in the group is excluded.
174/236
DS13314 Rev 3
1/fADC
µA
µA/
MHz
STM32H733xG
Electrical characteristics
6.
fADC value corresponds to the maximum frequency that can be reached considering a 2.5 sampling period. For other SMPy sampling periods,
the maximum frequency is fADC value * SMPy / 2.5 with a limitation to 75 MHz.
7.
The tolerance is 2 LSBs for 12-bit, 10-bit and 8-bit resolutions. It is otherwise specified.
Table 84. Minimum sampling time vs RAIN (12-bit ADC)(1)(2)
Resolution
12 bits
10 bits
RAIN (Ω)
Minimum sampling time (s)
Direct channels(3)
Fast channels(4)
Slow channels(5)
47
5.55E-08
7.04E-08
1.03E-07
68
5.76E-08
7.22E-08
1.05E-07
100
6.17E-08
7.65E-08
1.07E-07
150
7.02E-08
8.45E-08
1.13E-07
220
8.59E-08
1.00E-07
1.22E-07
330
1.11E-07
1.26E-07
1.41E-07
470
1.46E-07
1.61E-07
1.69E-07
680
1.98E-07
2.17E-07
2.25E-07
47
4.90E-08
6.06E-08
8.77E-08
68
5.07E-08
6.27E-08
8.95E-08
100
5.41E-08
6.67E-08
9.22E-08
150
6.18E-08
7.50E-08
9.59E-08
220
7.51E-08
8.70E-08
1.04E-07
330
9.46E-08
1.07E-07
1.17E-07
470
1.22E-07
1.34E-07
1.42E-07
680
1.63E-07
1.77E-07
1.86E-07
1000
2.27E-07
2.42E-07
2.43E-07
1500
3.27E-07
3.40E-07
3.35E-07
2200
4.53E-07
4.86E-07
4.73E-07
3300
6.56E-07
6.93E-07
6.72E-07
DS13314 Rev 3
175/236
216
Electrical characteristics
STM32H733xG
Table 84. Minimum sampling time vs RAIN (12-bit ADC)(1)(2) (continued)
Resolution
8 bits
6 bits
RAIN (Ω)
Minimum sampling time (s)
Direct channels(3)
Fast channels(4)
Slow channels(5)
47
4.35E-08
5.31E-08
7.36E-08
68
4.47E-08
5.48E-08
7.47E-08
100
4.72E-08
5.79E-08
7.63E-08
150
5.33E-08
6.35E-08
7.88E-08
220
6.26E-08
7.26E-08
8.47E-08
330
7.84E-08
8.80E-08
9.48E-08
470
9.80E-08
1.07E-07
1.14E-07
680
1.28E-07
1.39E-07
1.43E-07
1000
1.76E-07
1.88E-07
1.90E-07
1500
2.49E-07
2.66E-07
2.64E-07
2200
3.50E-07
3.63E-07
3.63E-07
3300
5.09E-07
5.27E-07
5.24E-07
4700
7.00E-07
7.28E-07
7.09E-07
6800
9.84E-07
1.03E-06
1.00E-06
10000
1.43E-06
1.48E-06
1.44E-06
15000
2.10E-06
2.18E-06
2.11E-06
47
3.79E-08
4.58E-08
5.74E-08
68
3.88E-08
4.69E-08
5.81E-08
100
4.09E-08
4.89E-08
5.93E-08
150
4.48E-08
5.25E-08
6.14E-08
220
5.07E-08
5.81E-08
6.58E-08
330
6.04E-08
6.79E-08
7.46E-08
470
7.37E-08
8.10E-08
8.60E-08
680
9.31E-08
1.01E-07
1.04E-07
1000
1.23E-07
1.32E-07
1.34E-07
1500
1.71E-07
1.82E-07
1.82E-07
2200
2.39E-07
2.50E-07
2.49E-07
3300
3.43E-07
3.57E-07
3.49E-07
4700
4.72E-07
4.92E-07
4.81E-07
6800
6.65E-07
6.89E-07
6.68E-07
10000
9.54E-07
9.88E-07
9.54E-07
15000
1.40E-06
1.45E-06
1.39E-06
1. Guaranteed by design.
2. Data valid up to 130 °C, with a 22 pF PCB capacitor and VDDA = 1.62 V.
176/236
DS13314 Rev 3
STM32H733xG
Electrical characteristics
3. Direct channels are connected to analog I/Os (PA0_C, PA1_C, PC2_C and PC3_C) to optimize ADC performance.
4. Fast channels correspond to ADCx_INx[0:5].
5. Slow channels correspond to all ADC inputs except for the Direct and Fast channels.
Table 85. 12-bit ADC accuracy(1)(2)
Symbol
Parameter
Conditions
Direct channel
ET
Total
unadjusted
error
Fast channel
Slow channel
Min
Typ
Max
Single
ended
-
3.5
5
Differential
-
2.5
3
Single
ended
-
3.5
5
Differential
-
2.5
3
Single
ended
-
3.5
5
Differential
-
2.5
3
+/-2
+/-5
Unit
EO
Offset error
-
-
EG
Gain error
-
-
Single ended
-
ED
Differential
linearity
error
+/0.75
Differential
-
+/-0.5
+1.25
/-1
Single
ended
-
+/-1
+/-2.5
Differential
-
+/-1
+/-2
Single
ended
-
+/-1
+/-2.5
Differential
-
+/-1
+/-2
Single
ended
-
+/-1
+/-2.5
Differential
-
+/-1
+/-2
Direct channel
EL
Integral
linearity
error
Fast channel
Slow channel
TBD
(3)
+1.5/- ±LSB
1
Effective
number of
bits
Single ended
-
11.2
-
ENOB
Differential
-
11.5
-
Single ended
-
68.9
-
SINAD
Signal-tonoise and
distortion
ratio
Differential
-
71.1
-
SNR
Signal-tonoise ratio
Single ended
-
69.1
-
Differential
-
71.4
-
Total
harmonic
distortion
Single ended
-
-79.6
-
THD
Differential
-
-81.8
-
DS13314 Rev 3
bits
dB
177/236
216
Electrical characteristics
STM32H733xG
1. Guaranteed by characterization for BGA packages. The maximum values are preliminary data. The values for LQFP
packages may be different.
2. ADC DC accuracy values are measured after internal calibration in Continuous and Discontinuous mode.
3. TBD stands for “to be defined”.
6.3.23
DAC characteristics
Table 86. DAC characteristics(1)
Symbol
Parameter
Conditions
Min
Typ
Max
VDDA
Analog supply voltage
-
1.8
3.3
3.6
VREF+
Positive reference voltage
-
1.80
-
VDDA
VREF-
Negative reference
voltage
-
-
VSSA
-
connected
to VSSA
5
-
-
connected
to VDDA
25
-
-
10.3
13
16
VDD = 2.7 V
-
-
1.6
VDD = 2.0 V
-
-
2.6
VDD = 2.7 V
-
-
17.8
VDD = 2.0 V
-
-
18.7
DAC output buffer OFF
-
-
50
pF
Sample and Hold mode
-
0.1
1
µF
DAC output buffer ON
0.2
-
VDDA
−0.2
V
DAC output buffer OFF
0
-
VREF+
±0.5 LSB
-
2.05
3
±1 LSB
-
1.97
2.87
±2 LSB
-
1.67
2.84
±4 LSB
-
1.66
2.78
±8 LSB
-
1.65
2.7
Normal mode, DAC output buffer
OFF, ±1LSB CL=10 pF
-
1.7
2
Normal mode, DAC output buffer
ON, CL ≤ 50 pF, RL = 5 ㏀
-
5
7.5
2
5
−80
−28
RL
Resistive Load
DAC output buffer
ON
RO
Output Impedance
RBON
Output impedance
sample and hold mode,
output buffer ON
DAC output buffer
ON
RBOFF
Output impedance
sample and hold mode,
output buffer OFF
DAC output buffer
OFF
CL
CSH
VDAC_OUT
Capacitive Load
Voltage on DAC_OUT
output
Settling time (full scale:
for a 12-bit code transition
between the lowest and
the highest input codes
tSETTLING
when DAC_OUT reaches
the final value of ±0.5LSB,
±1LSB, ±2LSB, ±4LSB,
±8LSB)
DAC output buffer OFF
Normal mode, DAC
output buffer ON,
CL ≤ 50 pF,
RL ≥ 5 ㏀
Wakeup time from off
state (setting the ENx bit
in the DAC Control
tWAKEUP(2)
register) until the final
value of ±1LSB is reached
Normal mode, DAC output buffer
OFF, CL ≤ 10 pF
DC VDDA supply rejection
ratio
Normal mode, DAC output buffer
ON, CL ≤ 50 pF, RL = 5 ㏀
PSRR
178/236
DS13314 Rev 3
Unit
V
kΩ
kΩ
kΩ
µs
µs
-
dB
STM32H733xG
Electrical characteristics
Table 86. DAC characteristics(1) (continued)
Symbol
Parameter
Conditions
Min
Typ
Max
MODE<2:0>_V12=100/101
(BUFFER ON)
-
0.7
2.6
tSAMP
Sampling time in Sample
and Hold mode
CL=100 nF
(code transition between
the lowest input code and
the highest input code
when DAC_OUT reaches
the ±1LSB final value)
MODE<2:0>_V12=110
(BUFFER OFF)
-
11.5
18.7
MODE<2:0>_V12=111
(INTERNAL BUFFER OFF)
-
0.3
0.6
Unit
ms
(3)
µs
Ileak
Output leakage current
-
CIint
Internal sample and hold
capacitor
-
1.8
2.2
2.6
pF
tTRIM
Middle code offset trim
time
Minimum time to verify the each
code
50
-
-
µs
Voffset
Middle code offset for 1
trim code step
VREF+ = 3.6 V
-
850
-
VREF+ = 1.8 V
-
425
-
No load,
middle code
(0x800)
-
360
-
No load,
worst code
(0xF1C)
-
490
-
No load,
middle/
worst code
(0x800)
-
20
-
-
360*TON/
(TON+TOFF)
-
No load,
middle code
(0x800)
-
170
-
No load,
worst code
(0xF1C)
-
170
-
No load,
middle/
worst code
(0x800)
-
160
-
Sample and Hold mode, Buffer
ON, CSH=100 nF (worst code)
-
170*TON/
(TON+TOFF)
-
Sample and Hold mode, Buffer
OFF, CSH=100 nF (worst code)
-
160*TON/
(TON+TOFF)
-
DAC output buffer
ON
IDDA(DAC)
DAC quiescent
consumption from VDDA
DAC output buffer
OFF
Sample and Hold mode,
CSH=100 nF
DAC output buffer
ON
IDDV(DAC)
DAC consumption from
VREF+
DAC output buffer
OFF
(4)
(4)
(4)
nA
µV
µA
1. Guaranteed by design unless otherwise specified.
DS13314 Rev 3
179/236
216
Electrical characteristics
STM32H733xG
2. In buffered mode, the output can overshoot above the final value for low input code (starting from the minimum value).
3. Refer to Table 51: I/O static characteristics.
4. TON is the refresh phase duration, while TOFF is the hold phase duration. Refer to the product reference manual for more
details.
Table 87. DAC accuracy(1)
Symbol
Parameter
Conditions
Min
Typ
Max
DNL
Differential non
linearity(2)
DAC output buffer ON
−2
-
2
DAC output buffer OFF
−2
-
2
-
Monotonicity
10 bits
-
-
-
DAC output buffer ON, CL ≤ 50 pF,
RL ≥ 5 ㏀
−4
-
4
DAC output buffer OFF,
CL ≤ 50 pF, no RL
−4
-
4
VREF+ = 3.6 V
-
-
±12
VREF+ = 1.8 V
-
-
±25
DAC output buffer OFF,
CL ≤ 50 pF, no RL
-
-
±8
DAC output buffer OFF,
CL ≤ 50 pF, no RL
-
-
±5
VREF+ = 3.6 V
-
-
±5
VREF+ = 1.8 V
-
-
±7
DAC output buffer ON,CL ≤ 50 pF,
RL ≥ 5 ㏀
-
-
±1
DAC output buffer OFF,
CL ≤ 50 pF, no RL
-
-
±1
DAC output buffer ON, CL ≤ 50 pF,
RL ≥ 5 ㏀
-
-
±30
INL
Offset
Integral non
linearity(3)
Offset error at code
0x800 (3)
Offset1
Offset error at code
0x001(4)
OffsetCal
Offset error at code
0x800 after factory
calibration
Gain
TUE
TUECal
SNR
180/236
Gain error(5)
Total unadjusted error
DAC output
buffer ON,
CL ≤ 50 pF,
RL ≥ 5 ㏀
DAC output
buffer ON,
CL ≤ 50 pF,
RL ≥ 5 ㏀
-
LSB
LSB
LSB
%
DAC output buffer OFF, CL ≤
50 pF, no RL
±12
-
-
±23
DAC output buffer ON,CL ≤ 50 pF,
RL ≥ 5 ㏀ , 1 kHz, BW = 500 KHz
-
67.8
-
DAC output buffer OFF,
CL ≤ 50 pF, no RL,1 kHz, BW =
500 KHz
-
67.8
-
DS13314 Rev 3
LSB
LSB
Total unadjusted error DAC output buffer ON, CL ≤ 50 pF,
after calibration
RL ≥ 5 ㏀
Signal-to-noise ratio(6)
Unit
LSB
dB
STM32H733xG
Electrical characteristics
Table 87. DAC accuracy(1) (continued)
Symbol
THD
SINAD
ENOB
Parameter
Total harmonic
distortion(6)
Signal-to-noise and
distortion ratio(6)
Conditions
Min
Typ
Max
DAC output buffer ON, CL ≤ 50 pF,
RL ≥ 5 ㏀ , 1 kHz
-
−78.6
-
DAC output buffer OFF,
CL ≤ 50 pF, no RL, 1 kHz
-
−78.6
-
DAC output buffer ON, CL ≤ 50 pF,
RL ≥ 5 ㏀ , 1 kHz
-
67.5
-
DAC output buffer OFF,
CL ≤ 50 pF, no RL, 1 kHz
-
67.5
-
DAC output buffer ON,
CL ≤ 50 pF, RL ≥ 5 ㏀ , 1 kHz
-
10.9
-
DAC output buffer OFF,
CL ≤ 50 pF, no RL, 1 kHz
-
Effective number of
bits
Unit
dB
dB
bits
10.9
-
1. Guaranteed by characterization results.
2. Difference between two consecutive codes minus 1 LSB.
3. Difference between the value measured at Code i and the value measured at Code i on a line drawn between Code 0 and
last Code 4095.
4. Difference between the value measured at Code (0x001) and the ideal value.
5. Difference between the ideal slope of the transfer function and the measured slope computed from code 0x000 and 0xFFF
when the buffer is OFF, and from code giving 0.2 V and (VREF+ - 0.2 V) when the buffer is ON.
6. Signal is −0.5dBFS with Fsampling=1 MHz.
Figure 41. 12-bit buffered /non-buffered DAC
Buffered/Non-buffered DAC
Buffer(1)
RL
DAC_OUTx
12-bit
digital to
analog
converter
CL
ai17157V3
1. The DAC integrates an output buffer that can be used to reduce the output impedance and to drive external loads directly
without the use of an external operational amplifier. The buffer can be bypassed by configuring the BOFFx bit in the
DAC_CR register.
DS13314 Rev 3
181/236
216
Electrical characteristics
6.3.24
STM32H733xG
Voltage reference buffer characteristics
Table 88. VREFBUF characteristics(1)
Symbol
Parameter
Conditions
Normal mode,
VDDA = 3.3 V
VDDA
Analog supply voltage
Degraded mode(2)
Normal mode at 30 °C,
Iload = 100 µA
VREFBUF
_OUT
Voltage Reference
Buffer Output, at 30 °C,
Iload= 100 µA
Degraded
Min
Typ
Max
VSCALE = 000
2.8
3.3
3.6
VSCALE = 001
2.4
-
3.6
VSCALE = 010
2.1
-
3.6
VSCALE = 011
1.8
-
3.6
VSCALE = 000
1.62
-
2.80
VSCALE = 001
1.62
-
2.40
VSCALE = 010
1.62
-
2.10
VSCALE = 011
1.62
-
1.80
VSCALE = 000
2.4980
2.5000
2.5035
VSCALE = 001
2.0460
2.0490
2.0520
VSCALE = 010
1.8010
1.8040
1.8060
VSCALE = 011
1.4995
1.5015
1.5040
VSCALE = 000
VDDA−
150 mV
-
VDDA
VSCALE = 001
VDDA−
150 mV
-
VDDA
VSCALE = 010
VDDA−
150 mV
-
VDDA
VSCALE = 011
VDDA−
150 mV
-
VDDA
mode(2)
Unit
V
TRIM
Trim step resolution
-
-
-
±0.05
±0.1
%
CL
Load capacitor
-
-
0.5
1
1.50
µF
esr
Equivalent Serial
Resistor of CL
-
-
-
-
2
Ω
ILOAD
Static load current
-
-
-
-
4
mA
Iline_reg
Line regulation
2.8 V ≤ VDDA ≤ 3.6 V
Iload = 500 µA
-
200
-
Iload = 4 mA
-
100
-
Iload_reg
Load regulation
500 µA ≤ ILOAD ≤ 4 mA
Normal mode
-
50
-
ppm/
mA
Tcoeff
Temperature coefficient
-
-
Tcoeff
VREFINT
+ 100
ppm/
°C
PSRR
Power supply rejection
182/236
−40 °C < TJ < +130 °C
DC
-
-
60
-
100KHz
-
-
40
-
DS13314 Rev 3
ppm/V
dB
STM32H733xG
Electrical characteristics
Table 88. VREFBUF characteristics(1) (continued)
Symbol
tSTART
IINRUSH
IDDA
(VREFBUF)
Parameter
Conditions
Start-up time
Typ
Max
CL=0.5 µF
-
-
300
-
CL=1 µF
-
-
500
-
CL=1.5 µF
-
-
650
-
-
8
-
Control of maximum
DC current drive on
VREFBUF_OUT during
startup phase(3)
-
VREFBUF
consumption from
VDDA
Min
Unit
µs
mA
ILOAD = 0 µA
-
-
15
25
ILOAD = 500 µA
-
-
16
30
ILOAD = 4 mA
-
-
32
50
µA
1. Guaranteed by design, unless otherwise specified.
2.
In degraded mode, the voltage reference buffer cannot accurately maintain the output voltage (VDDA−drop voltage).
3. To properly control VREFBUF IINRUSH current during the startup phase and the change of scaling, VDDA voltage should be in
the range of 1.8 V-3.6 V, 2.1 V-3.6 V, 2.4 V-3.6 V and 2.8 V-3.6 V for VSCALE = 011, 010, 001 and 000, respectively.
6.3.25
Analog temperature sensor characteristics
Table 89. Temperature sensor characteristics
Symbol
Parameter
TL(1)
(2)
Avg_Slope
V30(3)
tstart_run
tS_temp
(1)
Isens(1)
Isensbuf(1)
Min
Typ
Max
Unit
VSENSE linearity with temperature
-
-
±3
°C
Average slope
-
2
-
mV/°C
Voltage at 30°C ± 5 °C
-
0.62
-
V
Startup time in Run mode (buffer startup)
-
-
25.2
ADC sampling time when reading the temperature
9
-
-
Sensor consumption
-
0.18 0.31
Sensor buffer consumption
-
3.8
µs
µA
6.5
1. Guaranteed by design.
2. Guaranteed by characterization results.
3. Measured at VDDA = 3.3 V ± 10 mV. The V30 ADC conversion result is stored in the TS_CAL1
byte.
Table 90. Temperature sensor calibration values
Symbol
Parameter
Memory address
TS_CAL1
Temperature sensor raw data acquired value at
30 °C, VDDA=3.3 V
0x1FF1 E820 -0x1FF1 E821
TS_CAL2
Temperature sensor raw data acquired value at
130 °C, VDDA=3.3 V
0x1FF1 E840 - 0x1FF1 E841
DS13314 Rev 3
183/236
216
Electrical characteristics
6.3.26
STM32H733xG
Digital temperature sensor characteristics
Table 91. Digital temperature sensor characteristics(1)
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
fDTS(2)
Output Clock frequency
-
500
750
1150
kHz
TLC(2)
Temperature linearity coefficient
VOS2
1660
2100
2750
Hz/°
C
TJ = −40°C to
30°C
−13
-
4
TJ = 30°C to
Tjmax
−7
-
2
VOS2
0
-
0
VOS0, VOS1,
VOS3
−1
-
1
TTOTAL_ERROR
(2)
Temperature offset
measurement, all VOS
°C
TVDD_CORE
Additional error due to supply
variation
tTRIM
Calibration time
-
-
-
2
ms
tWAKE_UP
Wake-up time from off state until
DTS ready bit is set
-
-
67
116.00
μs
IDDCORE_DTS
DTS consumption on
VDD_CORE
-
8.5
30
70.0
μA
°C
1. Guaranteed by design, unless otherwise specified.
2. Guaranteed by characterization results.
6.3.27
Temperature and VBAT monitoring
Table 92. VBAT monitoring characteristics
Symbol
Parameter
Min
Typ
Max
Unit
R
Resistor bridge for VBAT
-
26
-
KΩ
Q
Ratio on VBAT measurement
-
4
-
-
–10
-
+10
%
µs
(1)
Error on Q
Er
tS_vbat(1)
ADC sampling time when reading VBAT input
9
-
-
VBAThigh
High supply monitoring
-
3.55
-
VBATlow
Low supply monitoring
-
1.36
-
V
1. Guaranteed by design.
Table 93. VBAT charging characteristics
Symbol
RBC
184/236
Parameter
Battery charging resistor
Condition
Min
Typ
Max
VBRS in PWR_CR3= 0
-
5
-
1.5
-
VBRS in PWR_CR3= 1
DS13314 Rev 3
Unit
KΩ
STM32H733xG
Electrical characteristics
Table 94. Temperature monitoring characteristics
Symbol
6.3.28
Parameter
Min
Typ
Max
TEMPhigh
High temperature monitoring
-
117
-
TEMPlow
Low temperature monitoring
-
–25
-
Unit
°C
Voltage booster for analog switch
Table 95. Voltage booster for analog switch characteristics(1)
Symbol
VDD
Parameter
Condition
Min
Typ Max Unit
-
1.62
2.6
3.6
V
-
-
-
50
µs
1.62 V ≤ VDD ≤ 2.7 V
-
-
125
2.7 V < VDD < 3.6 V
-
-
250
Supply voltage
tSU(BOOST) Booster startup time
IDD(BOOST) Booster consumption
µA
1. Guaranteed by characterization results.
6.3.29
Comparator characteristics
Table 96. COMP characteristics(1)
Symbol
Conditions
Min
Typ
Max
Analog supply voltage
-
1.62
3.3
3.6
VIN
Comparator input voltage
range
-
0
-
VDDA
V
VBG
Scaler input voltage
-
VSC
Scaler offset voltage
-
-
±5
±10
mV
BRG_EN=0 (bridge disable)
-
0.2
0.3
BRG_EN=1 (bridge enable)
-
0.8
1
-
-
140
250
High-speed mode
-
2
5
Medium mode
-
5
20
Ultra-low-power mode
-
15
80
High-speed mode
-
50
80
Medium mode
-
0.5
0.9
Ultra-low-power mode
-
2.5
7
High-speed mode
-
50
120
Medium mode
-
0.5
1.2
Ultra-low-power mode
-
2.5
7
Full common mode range
-
±5
±20
VDDA
IDDA(SCALER)
Parameter
Scaler static consumption
from VDDA
tSTART_SCALER Scaler startup time
tSTART
Comparator startup time to
reach propagation delay
specification
Propagation delay for
200 mV step with 100 mV
overdrive
tD
(3)
Voffset
Propagation delay for step
> 200 mV with 100 mV
overdrive only on positive
inputs
Comparator offset error
DS13314 Rev 3
Unit
(2)
µA
µs
µs
ns
µs
ns
µs
mV
185/236
216
Electrical characteristics
STM32H733xG
Table 96. COMP characteristics(1) (continued)
Symbol
Parameter
Vhys
Comparator hysteresis
Conditions
Min
Typ
Max
No hysteresis
-
0
-
Low hysteresis
4
10
22
Medium hysteresis
8
20
37
High hysteresis
16
30
52
Static
-
400
600
With 50 kHz
±100 mV overdrive
square signal
-
800
-
Static
-
5
7
-
6
-
Static
-
70
100
With 50 kHz
±100 mV overdrive
square signal
-
75
-
Ultra-lowpower mode
IDDA(COMP)
Comparator consumption
from VDDA
Medium mode With 50 kHz
±100 mV overdrive
square signal
High-speed
mode
Unit
mV
nA
µA
1. Guaranteed by design, unless otherwise specified.
2. Refer to Table 17: Embedded reference voltage.
3. Guaranteed by characterization results.
6.3.30
Operational amplifier characteristics
Table 97. Operational amplifier characteristics(1)
Symbol
Parameter
Conditions
Min
Typ
Max
VDDA
Analog supply voltage
Range
-
2
3.3
3.6
CMIR
Common Mode Input
Range
-
0
-
VDDA
25°C, no load on output
-
-
±1.5
V
VIOFFSET
Input offset voltage
All voltages and
temperature, no load
-
-
±2.5
ΔVIOFFSET
Input offset voltage drift
-
-
±3.0
-
TRIMOFFSETP
TRIMLPOFFSETP
Offset trim step at low
common input voltage
(0.1*VDDA)
-
-
1.1
1.5
TRIMOFFSETN
TRIMLPOFFSETN
Offset trim step at high
common input voltage
(0.9*VDDA)
-
-
1.1
1.5
ILOAD
Drive current
-
-
-
500
ILOAD_PGA
Drive current in PGA mode
-
-
-
270
186/236
Unit
mV
μV/°C
mV
DS13314 Rev 3
μA
STM32H733xG
Electrical characteristics
Table 97. Operational amplifier characteristics(1) (continued)
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
CLOAD
Capacitive load
-
-
-
50
pF
CMRR
Common mode rejection
ratio
-
-
80
-
dB
PSRR
Power supply rejection
ratio
CLOAD ≤ 50pf /
RLOAD ≥ 4 kΩ(2) at 1 kHz,
Vcom=VDDA/2
50
66
-
dB
GBW
Gain bandwidth for high
supply range
200 mV ≤ Output dynamic
range ≤ VDDA - 200 mV
4
7.3
12.3
MHz
SR
Slew rate (from 10% and
90% of output voltage)
Normal mode
-
3
-
High-speed mode
-
24
-
AO
Open loop gain
200 mV ≤ Output dynamic
range ≤ VDDA - 200 mV
59
90
129
dB
φm
Phase margin
-
-
55
-
°
GM
Gain margin
-
-
12
-
dB
VOHSAT
High saturation voltage
Iload=max or RLOAD=min,
Input at VDDA
VDDA
−100 mV
-
-
Low saturation voltage
Iload=max or RLOAD=min,
Input at 0 V
-
-
100
Normal
mode
CLOAD ≤ 50pf,
RLOAD ≥ 4 kΩ,
follower
configuration
-
0.8
3.2
High
speed
mode
CLOAD ≤ 50pf,
RLOAD ≥ 4 kΩ,
follower
configuration
-
0.9
2.8
PGA gain = 2
−1
-
1
PGA gain = 4
−2
-
2
PGA gain = 8
−2.5
-
2.5
PGA gain = 16
−3
-
3
PGA gain = 2
−1
-
1
PGA gain = 4
−1
-
1
PGA gain = 8
−2
-
2
PGA gain = 16
−3
-
3
PGA gain = 2
−1
-
1
PGA gain = 4
−3
-
3
PGA gain = 8
−3.5
-
3.5
PGA gain = 16
−4
-
4
VOLSAT
tWAKEUP
Wake up time from OFF
state
Non inverting gain error
value
PGA gain
Inverting gain error value
External non-inverting gain
error value
DS13314 Rev 3
V/µs
mV
µs
%
187/236
216
Electrical characteristics
STM32H733xG
Table 97. Operational amplifier characteristics(1) (continued)
Symbol
Parameter
R2/R1 internal resistance
values in non-inverting
PGA mode(3)
Rnetwork
R2/R1 internal resistance
values in inverting PGA
mode(3)
Delta R
Conditions
Min
Typ
Max
PGA Gain=2
-
10/10
-
PGA Gain=4
-
30/10
-
PGA Gain=8
-
70/10
-
PGA Gain=16
-
150/10
-
PGA Gain = -1
-
10/10
-
PGA Gain = -3
-
30/10
-
PGA Gain = -7
-
70/10
-
PGA Gain = -15
-
150/10
-
-
−15
-
15
Gain=2
-
GBW/2
-
Gain=4
-
GBW/4
-
Gain=8
-
GBW/8
-
Gain=16
-
GBW/16
-
Gain = -1
-
5.00
-
Gain = -3
-
3.00
-
Gain = -7
-
1.50
-
Gain = -15
-
0.80
-
-
140
-
-
55
-
-
570
1000
-
610
1200
Resistance variation (R1
or R2)
PGA bandwidth for
different non inverting gain
PGA BW
PGA bandwidth for
different inverting gain
en
IDDA(OPAMP)
Voltage noise density
OPAMP consumption from
VDDA
at
1 KHz
at
10 KHz
Normal
mode
Highspeed
mode
output loaded
with 4 kΩ
no Load,
quiescent mode,
follower
2. RLOAD is the resistive load connected to VSSA or to VDDA.
3. R2 is the internal resistance between the OPAMP output and th OPAMP inverting input. R1 is the internal resistance
between the OPAMP inverting input and ground. PGA gain = 1 + R2/R1.
DS13314 Rev 3
kΩ/
kΩ
%
MHz
MHz
nV/√
Hz
µA
1. Guaranteed by design, unless otherwise specified.
188/236
Unit
STM32H733xG
6.3.31
Electrical characteristics
Digital filter for Sigma-Delta Modulators (DFSDM) characteristics
Unless otherwise specified, the parameters given in Table 98 for DFSDM are derived from
tests performed under the ambient temperature, fPCLKx frequency and supply voltage
conditions summarized in Table 12: General operating conditions.
•
Output speed is set to OSPEEDRy[1:0] = 10
•
Capacitive load CL = 30 pF
•
Measurement points are done at CMOS levels: 0.5VDD
•
VOS level set to VOS0
Refer to Section 6.3.16: I/O port characteristics for more details on the input/output alternate
function characteristics (DìFSDM_CKINx, DFSDM_DATINx, DFSDM_CKOUT for DFSDM).
Table 98. DFSDM measured timing
Symbol
Parameter
Conditions
Min
Typ
Max
fDFSDMCLK
DFSDM
clock
1.62 < VDD < 3.6 V
-
-
fSYSCLK
SPI mode
(SITP[1:0] = 0,1),
External clock mode
(SPICKSEL[1:0] = 0)
-
-
20
SPI mode
(SITP[1:0] = 0,1),
Internal clock mode
(SPICKSEL[1:0] # 0)
-
-
20
1.62 < VDD < 3.6 V
-
-
20
Even
division,
CKOUTDIV
= n, 1, 3, 5..
45
50
55
Odd
division,
CKOUTDIV
= n, 2, 4, 6..
(((n/2+1)/(n+1))
*100)−5
fCKIN
(1/TCKIN)
fCKOUT
DuCyCKOUT
Input clock
frequency
Output clock
frequency
Output clock
frequency
duty cycle
1.62 < VDD
< 3.6 V
Unit
MHz
%
DS13314 Rev 3
(((n/2+1)/(n+1)) (((n/2+1)/(n+1))
*100)
*100)+5
189/236
216
Electrical characteristics
STM32H733xG
Table 98. DFSDM measured timing (continued)
Symbol
Parameter
Conditions
Min
Typ
Max
twh(CKIN)
twl(CKIN)
Input clock
high and low
time
SPI mode
(SITP[1:0] = 0,1),
External clock mode
(SPICKSEL[1:0] = 0)
TCKIN/2−0.5
TCKIN/2
-
tsu
Data input
setup time
SPI mode
(SITP[1:0] = 0,1),
External clock mode
(SPICKSEL[1:0] = 0)
2
-
-
th
Data input
hold time
SPI mode
(SITP[1:0] = 0,1),
External clock mode
(SPICKSEL[1:0] = 0)
1
-
-
TManchester
Manchester
data period
(recovered
clock period)
Manchester mode
(SITP[1:0] = 2,3),
Internal clock mode
(SPICKSEL[1:0] # 0)
(CKOUTDIV+1)
* TDFSDMCLK
-
(2*CKOUTDIV)
* TDFSDMCLK
190/236
Unit
ns
DS13314 Rev 3
STM32H733xG
Electrical characteristics
DFSDM_CKINy
DFSDM_DATINy
DFSDM_CKOUT
(SPICKSEL=0)
tsu
th
twl
twh
tr
tf
tr
tf
SITP = 00
tsu
th
SITP = 01
SPICKSEL=3
SPICKSEL=2
SPICKSEL=1
tsu
DFSDM_DATINy
SPI timing : SPICKSEL = 1, 2, 3
SPI timing : SPICKSEL = 0
Figure 42. Channel transceiver timing diagrams
th
twl
twh
SITP = 0
tsu
th
SITP = 1
DFSDM_DATINy
Manchester timing
SITP = 2
SITP = 3
recovered clock
recovered data
0
0
1
1
0
MS30766V2
DS13314 Rev 3
191/236
216
Electrical characteristics
6.3.32
STM32H733xG
Camera interface (DCMI) timing specifications
Unless otherwise specified, the parameters given in Table 99 for DCMI are derived from
tests performed under the ambient temperature, fHCLK frequency and VDD supply voltage
summarized in Table 12: General operating conditions, with the following configuration:
•
DCMI_PIXCLK polarity: falling
•
DCMI_VSYNC and DCMI_HSYNC polarity: high
•
Data formats: 14 bits
•
Capacitive load CL=30 pF
•
Measurement points are done at CMOS levels: 0.5VDD
•
VOS level set to VOS0
Table 99. DCMI characteristics(1)
Symbol
Parameter
Min
Max
Unit
-
Frequency ratio DCMI_PIXCLK/fHCLK
-
0.4
-
DCMI_PIXCLK
Pixel Clock input
-
110
MHz
Dpixel
Pixel Clock input duty cycle
30
70
%
tsu(DATA)
Data input setup time
2
-
th(DATA)
Data hold time
1
-
tsu(HSYNC),
tsu(VSYNC)
DCMI_HSYNC/ DCMI_VSYNC input setup time
2
-
th(HSYNC),
th(VSYNC)
DCMI_HSYNC/ DCMI_VSYNC input hold time
1
-
ns
1. Guaranteed by characterization results.
Figure 43. DCMI timing diagram
1/DCMI_PIXCLK
DCMI_PIXCLK
tsu(HSYNC)
th(HSYNC)
DCMI_HSYNC
tsu(VSYNC)
th(HSYNC)
DCMI_VSYNC
tsu(DATA) th(DATA)
DATA[0:13]
MS32414V2
192/236
DS13314 Rev 3
STM32H733xG
6.3.33
Electrical characteristics
Parallel synchronous slave interface (PSSI) characteristics
Unless otherwise specified, the parameters given in Table 100 and Table 101 for PSSI are
derived from tests performed under the ambient temperature, fHCLK frequency and VDD
supply voltage summarized in Table 12: General operating conditions.
Table 100. PSSI transmit characteristics(1)
Symbol
Parameter
Min
Max
Unit
-
Frequency ratio
PSSI_PDCK/fHCLK
-
0.4
-
PSSI_PDCK
PSSI Clock input
-
50
-
35(2)
Dpixel
PSSI Clock input duty cycle
30
70
tov(DATA)
Data output valid time
-
-
-
-
10
14(2)
toh(DATA)
Data output hold time
4.5
-
tov((DE)
DE output valid time
-
10
toh(DE)
DE output hold time
4
-
tsu(RDY)
RDY input setup time
0
-
th(RDY)
RDY input hold time
0
-
MHz
%
ns
1. Guaranteed by characterization results.
2. This value is obtained by using PA9, PA10 or PH4 I/O.
Table 101. PSSI receive characteristics(1)
Symbol
Parameter
Min
Max
Unit
-
Frequency ratio
PSSI_PDCK/fHCLK
-
0.4
-
PSSI_PDCK
PSSI Clock input
-
110
MHz
Dpixel
PSSI Clock input duty cycle
30
70
%
tsu(DATA)
Data input setup time
1.5
-
th(DATA)
Data input hold time
0.5
-
tsu((DE)
DE input setup time
2
-
th(DE)
DE input hold time
1
-
tov(RDY)
RDY output valid time
-
15
toh(RDY)
RDY output hold time
5.5
-
ns
1. Guaranteed by characterization results.
DS13314 Rev 3
193/236
216
Electrical characteristics
6.3.34
STM32H733xG
LCD-TFT controller (LTDC) characteristics
Unless otherwise specified, the parameters given in Table 102 for LCD-TFT are derived
from tests performed under the ambient temperature, fHCLK frequency and VDD supply
voltage summarized in Table 12: General operating conditions, with the following
configuration:
•
LCD_CLK polarity: high
•
LCD_DE polarity: low
•
LCD_VSYNC and LCD_HSYNC polarity: high
•
Pixel formats: 24 bits
•
Output speed is set to OSPEEDRy[1:0] = 11
•
Capacitive load CL=30 pF
•
Measurement points are done at CMOS levels: 0.5VDD
•
IO Compensation cell activated.
•
HSLV activated when VDD ≤ 2.7 V
•
VOS level set to VOS0
Table 102. LTDC characteristics(1)
Symbol
fCLK
Parameter
Min
2.7<VDD<3.6 V, 20 pF
LTDC clock
output
frequency
2.7<VDD<3.6 V
Max
150
-
133
LTDC clock output duty cycle
45
55
tw(CLKH),
tw(CLKL)
Clock High time, low time
tw(CLK)//2−0.5
tw(CLK)/2+0.5
th(DATA)
tv(HSYNC),
tv(VSYNC),
tv(DE)
th(HSYNC),
th(VSYNC),
th(DE)
2.7<VDD<3.6 V
Data output valid time
1.62<VDD<3.6 V
Data output hold time
HSYNC/VSYNC/DE output
valid time
-
%
2.0
2.5/6.5(2)
0
-
2.7<VDD<3.6 V
-
1.5
1.62<VDD<3.6 V
-
2.0
0
-
HSYNC/VSYNC/DE output hold time
MHz
90/76.5(2)
1.62<VDD<3.6 V
DCLK
tv(DATA)
Unit
ns
1. Guaranteed by characterization results.
2. This value is valid when PA[9], PA[10], PA[11], PA[12], PA[15], PB[11], PH[4], PJ[8], PJ[9], PJ[10], PJ[11], PK[0], PK[1] or
PK[2] is used.
194/236
DS13314 Rev 3
STM32H733xG
Electrical characteristics
Figure 44. LCD-TFT horizontal timing diagram
tCLK
LCD_CLK
LCD_VSYNC
tv(HSYNC)
tv(HSYNC)
LCD_HSYNC
th(DE)
tv(DE)
LCD_DE
tv(DATA)
LCD_R[0:7]
LCD_G[0:7]
LCD_B[0:7]
Pixel Pixel
1
2
Pixel
N
th(DATA)
HSYNC Horizontal
width back porch
Active width
Horizontal
back porch
One line
MS32749V1
Figure 45. LCD-TFT vertical timing diagram
tCLK
LCD_CLK
tv(VSYNC)
tv(VSYNC)
LCD_VSYNC
LCD_R[0:7]
LCD_G[0:7]
LCD_B[0:7]
M lines data
VSYNC Vertical
width back porch
Active width
Vertical
back porch
One frame
MS32750V1
DS13314 Rev 3
195/236
216
Electrical characteristics
6.3.35
STM32H733xG
Timer characteristics
The parameters given in Table 103 are guaranteed by design.
Refer to Section 6.3.16: I/O port characteristics for details on the input/output alternate
function characteristics (output compare, input capture, external clock, PWM output).
Table 103. TIMx characteristics(1)(2)
Symbol
tres(TIM)
fEXT
ResTIM
tMAX_COUNT
Conditions(3)
Min
Max
Unit
AHB/APBx prescaler=1
or 2 or 4, fTIMxCLK =
275 MHz
1
-
tTIMxCLK
AHB/APBx
prescaler>4, fTIMxCLK =
137.5 MHz
1
-
tTIMxCLK
Timer external clock
frequency on CH1 to CH4 f
TIMxCLK = 240 MHz
0
fTIMxCLK/2
MHz
Timer resolution
-
16/32
bit
-
65536 ×
65536
tTIMxCLK
Parameter
Timer resolution time
Maximum possible count
with 32-bit counter
-
1. TIMx is used as a general term to refer to the TIM1 to TIM17 timers.
2. Guaranteed by design.
3. The maximum timer frequency on APB1 or APB2 is up to 275 MHz, by setting the TIMPRE bit in the
RCC_CFGR register, if APBx prescaler is 1 or 2 or 4, then TIMxCLK = rcc_hclk1, otherwise TIMxCLK = 4x
Frcc_pclkx1 or TIMxCLK = 4x Frcc_pclkx2.
6.3.36
Low-power timer characteristics
The parameters given in Table 104 are guaranteed by design.
Refer to Section 6.3.16: I/O port characteristics for details on the input/output alternate
function characteristics (output compare, input capture, external clock, PWM output).
Table 104. LPTIMx characteristics(1)(2)
Symbol
tres(TIM)
fLPTIMxCLK
fEXT
ResTIM
Parameter
Min
Max
Unit
Timer resolution time
1
-
tTIMxCLK
Timer kernel clock
0
137.5
Timer external clock frequency on Input1 and
Input2
0
fLPTIMxCLK/2
Timer resolution
-
16
bit
-
65536
tTIMxCLK
tMAX_COUNT Maximum possible count
1. LPTIMx is used as a general term to refer to the LPTIM1 to LPTIM5 timers.
2. Guaranteed by design.
196/236
DS13314 Rev 3
MHz
STM32H733xG
6.3.37
Electrical characteristics
Communication interfaces
I2C interface characteristics
The I2C interface meets the timings requirements of the I2C-bus specification and user
manual revision 03 for:
•
Standard-mode (Sm): with a bit rate up to 100 kbit/s
•
Fast-mode (Fm): with a bit rate up to 400 kbit/s
•
Fast-mode Plus (Fm+): with a bit rate up to 1 Mbit/s.
I 2C
The
timings requirements are guaranteed by design when the I2C peripheral is properly
configured (refer to RM0399 reference manual) and when the i2c_ker_ck frequency is
greater than the minimum shown in the table below:
Table 105. Minimum i2c_ker_ck frequency in all I2C modes
Symbol
Parameter
Condition
Standard-mode
Fast-mode
f(I2CCLK)
I2CCLK
frequency
Fast-mode Plus
Min
-
2
Analog Filtre ON
DNF=0
8
Analog Filtre OFF
DNF=1
9
Analog Filtre ON
DNF=0
17
Analog Filtre OFF
DNF=1
16
Unit
MHz
-
The SDA and SCL I/O requirements are met with the following restrictions:
•
The SDA and SCL I/O pins are not “true” open-drain. When configured as open-drain,
the PMOS connected between the I/O pin and VDD is disabled, but still present.
•
The 20 mA output drive requirement in Fast-mode Plus is not supported. This limits the
maximum load CLoad supported in Fm+, which is given by these formulas:
tr(SDA/SCL)=0.8473xRP * CLoad
RP(min)= (VDD-VOL(max))/IOL(max)
Where RP is the I2C lines pull-up. Refer to Section 6.3.16: I/O port characteristics for
the I2C I/Os characteristics.
All I2C SDA and SCL I/Os embed an analog filter. Refer to the table below for the analog filter characteristics:
Table 106. I2C analog filter characteristics(1)
Symbol
Parameter
Min
Max
Unit
tAF
Maximum pulse width of spikes
that are suppressed by analog
filter
50(2)
80(3)
ns
1. Guaranteed by characterization results.
2. Spikes with widths below tAF(min) are filtered.
DS13314 Rev 3
197/236
216
Electrical characteristics
STM32H733xG
3. Spikes with widths above tAF(max) are not filtered.
USART interface characteristics
Unless otherwise specified, the parameters given in Table 107 for USART are derived from
tests performed under the ambient temperature, fPCLKx frequency and VDD supply voltage
conditions summarized in Table 12: General operating conditions, with the following
configuration:
•
Output speed is set to OSPEEDRy[1:0] = 11
•
Capacitive load CL = 30 pF
•
Measurement points are done at CMOS levels: 0.5VDD
•
IO Compensation cell activated.
•
VOS level set to VOS0
Refer to Section 6.3.16: I/O port characteristics for more details on the input/output alternate
function characteristics (NSS, CK, TX, RX for USART).
Table 107. USART characteristics(1)
Symbol
Parameter
Conditions
Master mode,
1.62 V < VDD < 3.6 V
fCK
USART clock frequency
Slave receiver mode,
1.62 V < VDD < 3.6 V
Slave transmitter mode,
1.62 V < VDD < 3.6 V
Slave transmitter mode,
2.5 V < VDD < 3.6 V
Min
Typ
Max
17.0
-
45.0
MHz
27.0
-
37.0
tsu(NSS)
NSS setup time
Slave mode
tker+1
-
-
th(NSS)
NSS hold time
Slave mode
2
-
-
tw(SCKH),
tw(SCKL)
CK high and low time
Master mode
1/fCK/2-2
1/fCK/2
1/fCK/2+2
tsu(RX)
Data input setup time
Master mode
16
-
-
Slave mode
1.0
-
-
th(RX)
Data input hold time
Master mode
0
-
-
Slave mode
2.0
-
-
Slave mode, ,
1.62 V < VDD < 3.6 V
-
12.0
18
Slave mode, ,
2.5 V < VDD < 3.6 V
-
12.0
13.5
Master mode
-
0.5
1
Slave mode
9
-
-
Master mode
0
-
-
tv(TX)
th(TX)
Data output valid time
Data output hold time
1. Guaranteed by characterization results.
198/236
DS13314 Rev 3
Unit
ns
STM32H733xG
Electrical characteristics
Figure 46. USART timing diagram in Master mode
CK output
CPHA = 0
CPOL = 0
CPHA = 0
CPOL = 1
CK output
1/fCK
CPHA = 1
CPOL = 0
CPHA = 1
CPOL = 1
tw(CKH)
tw(CKL)
tsu(RX)
RX
INPUT
BIT6 IN
MSB IN
LSB IN
th(RX)
TX
OUTPUT
BIT1 OUT
MSB OUT
tv(TX)
LSB OUT
th(TX)
MSv65386V4
1. Measurement points are done at 0.5VDD and with external CL = 30 pF.
Figure 47. USART timing diagram in Slave mode
NSS
input
1/fCK
CK input
tsu(NSS)
th(NSS)
tw(CKH)
CPHA = 0
CPOL = 0
CPHA = 0
CPOL = 1
tw(CKL)
tv(TX)
First bit OUT
TX output
th(TX)
Next bits OUT
Last bit OUT
th(RX)
tsu(RX)
RX input
First bit IN
Next bits IN
Last bit IN
MSv65387V4
DS13314 Rev 3
199/236
216
Electrical characteristics
STM32H733xG
SPI interface characteristics
Unless otherwise specified, the parameters given in Table 108 for SPI are derived from tests
performed under the ambient temperature, fPCLKx frequency and VDD supply voltage
conditions summarized in Table 12: General operating conditions, with the following
configuration:
•
Output speed is set to OSPEEDRy[1:0] = 11
•
Capacitive load CL = 30 pF
•
Measurement points are done at CMOS levels: 0.5VDD
•
IO Compensation cell activated.
•
HSLV activated when VDD ≤ 2.7 V
•
VOS level set to VOS0
Refer to Section 6.3.16: I/O port characteristics for more details on the input/output alternate
function characteristics (NSS, SCK, MOSI, MISO for SPI).
Table 108. SPI characteristics(1)(2)
Symbol
fSCK
Parameter
SPI clock frequency
Conditions
Min
Typ
Max
Master mode,
2.7 V < VDD < 3.6 V, SPI1, 2, 3
125
Master mode,
1.62 V < VDD < 3.6 V, SPI1, 2,
3
80/66(3)
Master mode,
1.62 V < VDD < 3.6 V, SPI4, 5,
6
68.5
Slave receiver mode,
1.62 V < VDD < 3.6 V, SPI1, 2,
3
-
-
100
Slave receiver mode,
1.62 V < VDD < 3.6 V, SPI4, 5,
6
68.5
Slave mode transmitter/full
duplex, 2.7 V < VDD < 3.6 V
45
Slave mode transmitter/full
duplex, 1.62 V < VDD < 3.6 V
42.5/31(4)
tsu(NSS)
NSS setup time
Slave mode
2
-
-
th(NSS)
NSS hold time
Slave mode
1
-
-
Master mode
/2-1(5)
tw(SCKH),
tw(SCKL)
200/236
SCK high and low time
DS13314 Rev 3
tSCK
tSCK/2(5)
tSCK
/2+1(5)
Unit
MHz
-
STM32H733xG
Electrical characteristics
Table 108. SPI characteristics(1)(2) (continued)
Symbol
tsu(MI)
tsu(SI)
Parameter
Data input setup time
th(MI)
Data input hold time
th(SI)
Conditions
Min
Typ
Max
Master mode
2.5
-
-
Slave mode
1
-
-
Master mode
3
-
-
Slave mode
1.5
-
-
Unit
ta(SO)
Data output access time
Slave mode
9
13
27
tdis(SO)
Data output disable time
Slave mode
0
1
5
Slave mode,
2.7 V < VDD < 3.6 V
-
7.5
11
Slave mode,
1.62 V < VDD < 3.6 V
-
7.5
12/16(4)
Master mode,
1.62 V < VDD < 3.6 V
-
1
1.5/5.5(6)
Slave mode
7
-
-
Master mode
0.5
-
-
tv(SO)
Data output valid time
tv(MO)
th(SO)
th(MO)
Data output hold time
ns
1. Guaranteed by characterization results.
2. The values given in the above table might be degraded when PC3_C/PC2_C I/Os are used (not available on all packages).
3. This value is obtained by using PA9 or PA12 I/O.
4. This value is obtained by using PC2 or PJ11 I/O.
5. tSCK = tker_ck * baud rate prescaler.
6. This value is obtained by using PC3 or PJ10 I/O.
Figure 48. SPI timing diagram - slave mode and CPHA = 0
NSS input
tc(SCK)
SCK input
tsu(NSS)
th(NSS)
tw(SCKH)
tr(SCK)
CPHA=0
CPOL=0
CPHA=0
CPOL=1
ta(SO)
tw(SCKL)
tv(SO)
First bit OUT
MISO output
th(SO)
Next bits OUT
tf(SCK)
tdis(SO)
Last bit OUT
th(SI)
tsu(SI)
MOSI input
First bit IN
Next bits IN
Last bit IN
MSv41658V1
DS13314 Rev 3
201/236
216
Electrical characteristics
STM32H733xG
Figure 49. SPI timing diagram - slave mode and CPHA = 1(1)
NSS input
tc(SCK)
tsu(NSS)
tw(SCKH)
ta(SO)
tw(SCKL)
tf(SCK)
th(NSS)
SCK input
CPHA=1
CPOL=0
CPHA=1
CPOL=1
tv(SO)
th(SO)
First bit OUT
MISO output
tsu(SI)
tr(SCK)
Next bits OUT
tdis(SO)
Last bit OUT
th(SI)
MOSI input
First bit IN
Next bits IN
Last bit IN
MSv41659V1
1. Measurement points are done at 0.5VDD and with external CL = 30 pF.
Figure 50. SPI timing diagram - master mode(1)
High
NSS input
SCK Output
CPHA= 0
CPOL=0
SCK Output
tc(SCK)
CPHA=1
CPOL=0
CPHA= 0
CPOL=1
CPHA=1
CPOL=1
tsu(MI)
MISO
INP UT
tw(SCKH)
tw(SCKL)
MSB IN
tr(SCK)
tf(SCK)
BIT6 IN
LSB IN
th(MI)
MOSI
OUTPUT
MSB OUT
tv(MO)
B I T1 OUT
LSB OUT
th(MO)
ai14136c
1. Measurement points are done at 0.5VDD and with external CL = 30 pF.
202/236
DS13314 Rev 3
STM32H733xG
Electrical characteristics
I2S Interface characteristics
Unless otherwise specified, the parameters given in Table 109 for I2S are derived from tests
performed under the ambient temperature, fPCLKx frequency and VDD supply voltage
conditions summarized in Table 12: General operating conditions, with the following
configuration:
•
Output speed is set to OSPEEDRy[1:0] = 11
•
Capacitive load CL = 30 pF
•
Measurement points are done at CMOS levels: 0.5VDD
•
IO Compensation cell activated.
•
HSLV activated when VDD ≤ 2.7 V
•
VOS level set to VOS0
Refer to Section 6.3.16: I/O port characteristics for more details on the input/output alternate
function characteristics (CK,SD,WS).
Table 109. I2S dynamic characteristics(1)
Symbol
Parameter
Conditions
Min
Max
-
50
Master transmitter
-
50/40(2)
Master receiver
-
50/40(2)
Slave transmitter
-
41.5/31(3)
Slave receiver
-
50
-
2/6(4)
1
-
3
-
1
-
Master receiver
2.5
-
Slave receiver
1
-
Master receiver
3
-
Slave receiver
1.5
-
Slave transmitter (after enable
edge)
-
12/16(3)
tv(SD_MT)
Master transmitter (after
enable edge)
-
2/6(5)
th(SD_ST)
Slave transmitter (after enable
edge)
6.5
-
Master transmitter (after
enable edge)
0.5
-
-
fMCK
I2S main clock output
tv(WS)
WS valid time
th(WS)
WS hold time
tsu(WS)
WS setup time
th(WS)
WS hold time
tsu(SD_MR)
tsu(SD_SR)
th(SD_MR)
th(SD_SR)
Master mode
Slave mode
Data input setup time
Data input hold time
tv(SD_ST)
Data output valid time
Data output hold time
th(SD_MT)
Unit
MHz
ns
1. Guaranteed by characterization results.
2. This value is obtained when PA9 or PA12 are used.
3. This value is obtained when PC2 is used.
4. This value is obtained when PA11 or PA15 are used.
DS13314 Rev 3
203/236
216
Electrical characteristics
STM32H733xG
5. This value is obtained when PC3 is used.
Figure 51. I2S slave timing diagram (Philips protocol)(1)
1. LSB transmit/receive of the previously transmitted byte. No LSB transmit/receive is sent before the first
byte.
Figure 52. I2S master timing diagram (Philips protocol)(1)
1. LSB transmit/receive of the previously transmitted byte. No LSB transmit/receive is sent before the first
byte.
204/236
DS13314 Rev 3
STM32H733xG
Electrical characteristics
SAI characteristics
Unless otherwise specified, the parameters given in Table 110 for SAI are derived from tests
performed under the ambient temperature, fPCLKx frequency and VDD supply voltage
conditions summarized in Table 12: General operating conditions, with the following
configuration:
•
Output speed is set to OSPEEDRy[1:0] = 10
•
Capacitive load CL = 30 pF
•
IO Compensation cell activated.
•
Measurement points are done at CMOS levels: 0.5VDD
•
VOS level set to VOS0
Refer to Section 6.3.16: I/O port characteristics for more details on the input/output
alternate function characteristics (SCK,SD,WS).
Table 110. SAI characteristics(1)
Symbol
Parameter
Conditions
Min
Max
fMCK
SAI Main clock output
-
-
50
Master transmitter, 2.7 V ≤ VDD ≤ 3.6 V
-
45
Master transmitter, 1.62 V ≤ VDD ≤ 3.6 V
-
32
Master receiver, 1.62 V ≤ VDD ≤ 3.6 V
-
32
Slave transmitter, 2.7 V ≤ VDD ≤ 3.6 V
-
47.5
Slave transmitter, 1.62 V ≤ VDD ≤ 3.6 V
-
41.5
Slave receiver, 1.62 V ≤ VDD ≤ 3.6 V
-
50
fCK
SAI clock frequency(2)
DS13314 Rev 3
Unit
MHz
205/236
216
Electrical characteristics
STM32H733xG
Table 110. SAI characteristics(1) (continued)
Symbol
Parameter
tv(FS)
FS valid time
tsu(FS)
FS setup time
th(FS)
FS hold time
tsu(SD_A_MR)
tsu(SD_B_SR)
th(SD_A_MR)
th(SD_B_SR)
tv(SD_B_ST)
th(SD_B_ST)
tv(SD_A_MT)
th(SD_A_MT)
Conditions
Min
Max
Master mode, 2.7 V ≤ VDD ≤ 3.6 V
-
11
Master mode, 1.62 V ≤ VDD ≤ 3.6 V
-
15.5
Slave mode
2.5
-
Master mode
6
-
Slave mode
0.5
-
Master receiver
3
-
Slave receiver
3.5
-
Master receiver
3.5
-
Slave receiver
0
-
Slave transmitter (after enable edge),
2.7 V ≤ VDD ≤ 3.6 V
-
10.5
Slave transmitter (after enable edge),
1.62 V ≤ VDD ≤ 3.6 V
-
12
Slave transmitter (after enable edge)
6.5
-
Master transmitter (after enable edge),
2.7 V ≤ VDD ≤ 3.6 V
-
10.5
Master transmitter (after enable edge),
1.62 V ≤ VDD ≤ 3.6 V
-
14.5
Master transmitter (after enable edge)
6
-
Data input setup time
Data input hold time
Data output valid time
Data output hold time
Data output valid time
Data output hold time
Unit
ns
1. Guaranteed by characterization results.
2. APB clock frequency must be at least twice SAI clock frequency.
Figure 53. SAI master timing waveforms
1/fSCK
SAI_SCK_X
th(FS)
SAI_FS_X
(output)
tv(FS)
th(SD_MT)
tv(SD_MT)
SAI_SD_X
(transmit)
Slot n
tsu(SD_MR)
SAI_SD_X
(receive)
Slot n+2
th(SD_MR)
Slot n
MS32771V1
206/236
DS13314 Rev 3
STM32H733xG
Electrical characteristics
Figure 54. SAI slave timing waveforms
1/fSCK
SAI_SCK_X
tw(CKH_X)
SAI_FS_X
(input)
tw(CKL_X)
th(FS)
tsu(FS)
th(SD_ST)
tv(SD_ST)
SAI_SD_X
(transmit)
Slot n
tsu(SD_SR)
SAI_SD_X
(receive)
Slot n+2
th(SD_SR)
Slot n
MS32772V1
MDIO characteristics
Unless otherwise specified, the parameters given in Table 111 for the MDIO are derived
from tests performed under the ambient temperature, fPCLKx frequency and VDD supply
voltage conditions summarized in Table 12: General operating conditions, with the following
configuration:
•
Output speed is set to OSPEEDRy[1:0] = 10
•
I/O Compensation cell activated.
•
Measurement points are done at CMOS levels: 0.5VDD
•
HSLV activated when VDD ≤ 2.7 V
•
VOS level set to VOS0
Table 111. MDIO Slave timing parameters
Symbol
Parameter
Min
Typ
Max
Unit
FMDC
Management Data Clock
-
-
30
MHz
td(MDIO)
Management Data Iput/output output valid time
8
10
18
tsu(MDIO)
Management Data Iput/output setup time
1
-
-
th(MDIO)
Management Data Iput/output hold time
1
-
-
DS13314 Rev 3
ns
207/236
216
Electrical characteristics
STM32H733xG
Figure 55. MDIO Slave timing diagram
tMDC)
td(MDIO)
tsu(MDIO)
th(MDIO)
MSv40460V1
SD/SDIO MMC card host interface (SDMMC) characteristics
Unless otherwise specified, the parameters given in Table 112 and Table 113 for SDIO are
derived from tests performed under the ambient temperature, fPCLKx frequency and VDD
supply voltage summarized in Table 12: General operating conditions, with the following
configuration:
•
Output speed is set to OSPEEDRy[1:0] = 11
•
Capacitive load CL=30 pF
•
Measurement points are done at CMOS levels: 0.5VDD
•
IO Compensation cell activated.
•
HSLV activated when VDD ≤ 2.7 V
•
VOS level set to VOS0
Refer to Section 6.3.16: I/O port characteristics for more details on the input/output
characteristics.
Table 112. Dynamics characteristics: SD / MMC characteristics, VDD = 2.7 to 3.6 V(1)(2)
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
fPP
Clock frequency in data transfer
mode
-
0
-
120
MHz
-
SDIO_CK/fPCLK2 frequency ratio
-
-
-
8/3
-
tW(CKL)
Clock low time
8.5
9.5
-
tW(CKH)
Clock high time
8.5
9.5
-
fPP =52MHz
ns
CMD, D inputs (referenced to CK) in eMMC legacy/SDR/DDR and SD HS/SDR/DDR mode
tISU
Input setup time HS
-
2.5
-
-
tIH
Input hold time HS
-
0.5
-
-
Input valid window (variable window)
-
1.5
-
-
tIDW
(3)
ns
CMD, D outputs (referenced to CK) in eMMC legacy/SDR/DDR and SD HS/SDR/DDR mode
208/236
tOV
Output valid time HS
-
-
5.5
6
tOH
Output hold time HS
-
4.5
-
-
DS13314 Rev 3
ns
STM32H733xG
Electrical characteristics
Table 112. Dynamics characteristics: SD / MMC characteristics, VDD = 2.7 to 3.6 V(1)(2)
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
CMD, D inputs (referenced to CK) in SD default mode
tISUD
Input setup time SD
-
1.5
-
tIHD
Input hold time SD
-
0.5
-
ns
CMD, D outputs (referenced to CK) in SD default mode
tOVD
Output valid default time SD
-
-
1
1
tOHD
Output hold default time SD
-
0
-
-
ns
1. Guaranteed by characterization results.
2. Above 100 MHz, CL = 20 pF.
3. The minimum window of time where the data needs to be stable for proper sampling in tuning mode.
Table 113. Dynamics characteristics: eMMC characteristics VDD = 1.71V to 1.9V(1)(2)
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
fPP
Clock frequency in data transfer
mode
-
0
-
85
MHz
-
SDIO_CK/fPCLK2 frequency ratio
-
-
-
8/3
-
tW(CKL)
Clock low time
8.5
9.5
-
tW(CKH)
Clock high time
8.5
9.5
-
fPP =52 MHz
ns
CMD, D inputs (referenced to CK) in eMMC mode
tISU
Input setup time HS
-
1.5
-
-
tIH
Input hold time HS
-
1.5
-
-
Input valid window (variable
window)
-
3.5
-
-
tIDW
(3)
ns
CMD, D outputs (referenced to CK) in eMMC mode
tOVD
Output valid time HS
-
-
6
6.5
tOHD
Output hold time HS
-
5.5
-
-
ns
1. Guaranteed by characterization results.
2. CL = 20 pF.
3. The minimum window of time where the data needs to be stable for proper sampling in tuning mode.
DS13314 Rev 3
209/236
216
Electrical characteristics
STM32H733xG
Figure 56. SD high-speed mode
tC(CK)
tW(CKH)
tW(CKL)
CK
tOH
tOV
D, CMD output
tIH
tISU
D, CMD input
MSv69709V1
Figure 57. SD default mode
CK
tOV
tOH
D, CMD output
MSv69710V1
Figure 58. SDMMC DDR mode
Valid data
D input
tISU
Valid data
tIH
tISU
tIH
tW(CKH)
CK
tW(CKL)
tOV
tOV
tOH
tOH
Valid data
D output
Valid data
MSv69158V1
USB OTG_FS characteristics
Unless otherwise specified, the parameters given in Table 115 for ULPI are derived from
tests performed under the ambient temperature, fPCLKx frequency and VDD supply voltage
summarized in Table 12: General operating conditions, with the following configuration:
210/236
•
Output speed is set to OSPEEDRy[1:0] = 11
•
Capacitive load CL=20 pF
•
Measurement points are done at CMOS levels: 0.5VDD
•
IO Compensation cell activated.
•
VOS level set to VOS0
DS13314 Rev 3
STM32H733xG
Electrical characteristics
Refer to Section 6.3.16: I/O port characteristics for more details on the input/output
characteristics.
Table 114. USB OTG_FS electrical characteristics
Symbol
Parameter
Condition
Min
Typ
Max
Unit
VDD33US
USB transceiver operating voltage
-
3.0(1)
-
3.6
V
RPUI
Embedded USB_DP pull-up value
during idle
-
900
1250
1600
RPUR
Embedded USB_DP pull-up value
during reception
-
1400
2300
3200
ZDRV
Output driver impedance(2)
Driver high
and low
28
36
44
B
Ω
1. The USB functionality is ensured down to 2.7 V. However, not all USB electrical characteristics are
degraded in the 2.7 to 3.0 V voltage range.
2. No external termination series resistors are required on USB_DP (D+) and USB_DM (D-); the matching
impedance is already included in the embedded driver.
USB OTG_HS characteristics
Unless otherwise specified, the parameters given in Table 115 for ULPI are derived from
tests performed under the ambient temperature, fPCLKx frequency and VDD supply voltage
summarized in Table 12: General operating conditions, with the following configuration:
•
Output speed is set to OSPEEDRy[1:0] = 11
•
Capacitive load CL=20 pF
•
Measurement points are done at CMOS levels: 0.5VDD
•
IO Compensation cell activated.
•
VOS level set to VOS0
Refer to Section 6.3.16: I/O port characteristics for more details on the input/output
characteristics.
Table 115. Dynamics characteristics: USB ULPI(1)
Symbol
Parameter
Condition
Min
Typ
Max
tSC
Control in (ULPI_DIR , ULPI_NXT)
setup time
-
5.5
-
-
tHC
Control in (ULPI_DIR, ULPI_NXT) hold
time
-
0
-
-
tSD
Data in setup time
-
2.5
-
-
tHD
Data in hold time
-
0
-
-
2.7 V < VDD < 3.6 V,
CL = 20 pF
-
6.0
8.0
1.71 V < VDD < 3.6 V
, CL = 15 pF
-
6.0
12
tDC/tDD
Control/Datal output delay
Unit
ns
1. Guaranteed by characterization results.
DS13314 Rev 3
211/236
216
Electrical characteristics
STM32H733xG
Figure 59. ULPI timing diagram
Clock
Control In
(ULPI_DIR,
ULPI_NXT)
tSC
tHC
tSD
tHD
data In
(8-bit)
tDC
tDC
Control out
(ULPI_STP)
tDD
data out
(8-bit)
ai17361c
Ethernet interface characteristics
Unless otherwise specified, the parameters given in Table 116, Table 117 and Table 118 for
SMI, RMII and MII are derived from tests performed under the ambient temperature,
frcc_c_ck frequency and VDD supply voltage conditions summarized in Table 12: General
operating conditions, with the following configuration:
•
Output speed is set to OSPEEDRy[1:0] = 10
•
Capacitive load CL=20 pF
•
Measurement points are done at CMOS levels: 0.5VDD
•
IO Compensation cell activated.
•
HSLV activated when VDD ≤ 2.7 V
•
VOS level set to VOS1
Refer to Section 6.3.16: I/O port characteristics for more details on the input/output
characteristics:
Table 116. Dynamics characteristics: Ethernet MAC signals for SMI (1)
Symbol
Parameter
Min
Typ
Max
tMDC
MDC cycle time( 2.5 MHz)
400
400
403
Td(MDIO)
Write data valid time
0.5
1.5
4
tsu(MDIO)
Read data setup time
12.5
-
-
th(MDIO)
Read data hold time
0
-
-
1. Guaranteed by characterization results.
212/236
DS13314 Rev 3
Unit
ns
STM32H733xG
Electrical characteristics
Figure 60. Ethernet SMI timing diagram
tMDC
ETH_MDC
td(MDIO)
ETH_MDIO(O)
tsu(MDIO)
th(MDIO)
ETH_MDIO(I)
MS31384V1
Table 117. Dynamics characteristics: Ethernet MAC signals for RMII (1)
Symbol
Parameter
Min
Typ
Max
tsu(RXD)
Receive data setup time
2
-
-
tih(RXD)
Receive data hold time
2
-
-
tsu(CRS)
Carrier sense setup time
1.5
-
-
tih(CRS)
Carrier sense hold time
1.5
-
-
td(TXEN)
Transmit enable valid delay time
8
0
10.5
td(TXD)
Transmit data valid delay time
7
8
9.5
Unit
ns
1. Guaranteed by characterization results.
Figure 61. Ethernet RMII timing diagram
RMII_REF_CLK
td(TXEN)
td(TXD)
RMII_TX_EN
RMII_TXD[1:0]
tsu(RXD)
tsu(CRS)
tih(RXD)
tih(CRS)
RMII_RXD[1:0]
RMII_CRS_DV
ai15667b
DS13314 Rev 3
213/236
216
Electrical characteristics
STM32H733xG
Table 118. Dynamics characteristics: Ethernet MAC signals for MII (1)
Symbol
Parameter
Min
Typ
Max
tsu(RXD)
Receive data setup time
2.0
-
-
tih(RXD)
Receive data hold time
2.0
-
-
tsu(DV)
Data valid setup time
1.5
-
-
tih(DV)
Data valid hold time
1.5
-
-
tsu(ER)
Error setup time
1.5
-
-
tih(ER)
Error hold time
0.5
-
-
td(TXEN)
Transmit enable valid delay time
9.0
11
19
td(TXD)
Transmit data valid delay time
8.5
10
19
Unit
ns
1. Guaranteed by characterization results.
Figure 62. Ethernet MII timing diagram
MII_RX_CLK
tsu(RXD)
tsu(ER)
tsu(DV)
tih(RXD)
tih(ER)
tih(DV)
MII_RXD[3:0]
MII_RX_DV
MII_RX_ER
MII_TX_CLK
td(TXEN)
td(TXD)
MII_TX_EN
MII_TXD[3:0]
ai15668b
JTAG/SWD interface characteristics
Unless otherwise specified, the parameters given in Table 119 and Table 120 for
JTAG/SWD are derived from tests performed under the ambient temperature, frcc_c_ck
frequency and VDD supply voltage summarized in Table 12: General operating conditions,
with the following configuration:
•
Output speed is set to OSPEEDRy[1:0] = 11
•
Capacitive load CL=30 pF
•
Measurement points are done at CMOS levels: 0.5VDD
•
VOS level set to VOS0
Refer to Section 6.3.16: I/O port characteristics for more details on the input/output
characteristics:
214/236
DS13314 Rev 3
STM32H733xG
Electrical characteristics
Table 119. Dynamics JTAG characteristics
Symbol
Fpp
1/tc(TCK)
Parameter
TCK clock frequency
Conditions
Min
Typ
Max
2.7V <VDD< 3.6 V
-
-
37
1.62 <VDD< 3.6 V
-
-
27.5
Unit
MHz
tisu(TMS)
TMS input setup time
-
2.5
-
-
tih(TMS)
TMS input hold time
-
1
-
-
tisu(TDI)
TDI input setup time
-
1.5
-
-
-
tih(TDI)
TDI input hold time
-
1
-
-
-
tov(TDO)
TDO output valid time
2.7V <VDD< 3.6 V
-
8
13.5
-
1.62 <VDD< 3.6 V
-
8
18
-
toh(TDO)
TDO output hold time
-
7
-
-
-
Unit
Table 120. Dynamics SWD characteristics
Symbol
Fpp
1/tc(SWCLK)
Parameter
SWCLK clock frequency
Conditions
Min
Typ
Max
2.7V <VDD< 3.6 V
-
-
71
1.62 <VDD< 3.6 V
-
-
52.5
MHz
tisu(SWDIO)
SWDIO input setup time
-
2.5
-
-
-
tih(SWDIO)
SWDIO input hold time
-
1
-
-
-
2.7V <VDD< 3.6 V
-
8.5
14
-
-
8.5
19
-
8
-
-
-
tov(SWDIO)
SWDIO output valid time
1.62 <VDD< 3.6 V
toh(SWDIO)
SWDIO output hold time
-
Figure 63. JTAG timing diagram
tc(TCK)
TCK
tsu(TMS/TDI)
th(TMS/TDI)
tw(TCKL) tw(TCKH)
TDI/TMS
tov(TDO)
toh(TDO)
TDO
MSv40458V1
DS13314 Rev 3
215/236
216
Electrical characteristics
STM32H733xG
Figure 64. SWD timing diagram
tc(SWCLK)
SWCLK
tsu(SWDIO)
th(SWDIO)
twSWCLKL) tw(SWCLKH)
SWDIO
(receive)
tov(SWDIO)
toh(SWDIO)
SWDIO
(transmit)
MSv40459V1
216/236
DS13314 Rev 3
Package information
7
STM32H733xG
Package information
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK packages, depending on their level of environmental compliance. ECOPACK
specifications, grade definitions and product status are available at www.st.com. ECOPACK
is an ST trademark.
216/236
DS13314 Rev 3
STM32H733xG
7.1
Package information
LQFP100 package information
This LQFP100 is a 100-pin, 14 x 14 mm low-profile quad flat package.
Figure 65. LQFP100- Outline
θ1
θ2
R1
R2
(4)
B
D1/4
SE
C
TI
O
N
BB
H
GAUGE PLANE
S
θ
B
E1/4
θ3
4x N/4 TIPS
L
4x
aaa C A-B D
L1
bbb H A-B D
SECTION A-A
BOTTOM VIEW
(N-4) x e
C
A
0.05
A2 A1
b
aaa
b
ccc C
C A-BD
WITH PLATING
SIDE VIEW
D
D1
c
c1
D
(5)
N
b1
1
2
3
E1/4
D1/4
BASE METAL
SECTION B-B
(4)
B
A
E1
E
SECTION A-A
A
A
TOP VIEW
1L_LQFP100_ME_V2
1. Drawing is not to scale.
DS13314 Rev 3
217/236
233
Package information
STM32H733xG
Table 121. LQFP100 - Mechanical data
inches(1)
millimeters
Symbol
A
(2)
A1
Min
Typ
Max
Min
Typ
Max
-
1.50
1.60
-
0.0590
0.0630
0.05
-
0.15
0.0019
-
0.0059
A2
1.35
1.40
1.45
0.0531
0.0551
0.0570
(3)(4)
0.17
0.22
0.27
0.0067
0.0087
0.0106
(4)
0.17
0.20
0.23
0.0067
0.0079
0.0090
0.09
-
0.20
0.0035
-
0.0079
0.09
-
0.16
0.0035
-
0.0063
b
b1
(4)
c
c1(4)
(5)
16.00
0.6299
(6)(7)
D
14.00
0.5512
E(5)
16.00
0.6299
E1(6)(7)
14.00
0.5512
D1
e
-
0.50
-
-
0.0197
-
L
0.45
0.60
0.75
0.177
0.0236
0.0295
-
0.0394
-
L1
(4)
1.00
N(8)
100
θ
0°
3.5°
7°
0°
3.5°
7°
θ1
0°
-
-
0°
-
-
θ2
10°
12°
14°
10°
12°
14°
θ3
10°
12°
14°
10°
12°
14°
R1
0.08
-
-
0.0031
-
-
R2
0.08
-
0.20
0.0031
-
0.0079
S
0.20
-
-
0.0079
-
-
aaa(9)
0.20
0.0079
bbb(9)
0.20
0.0079
(9)
0.08
0.0031
(9)
0.08
0.0031
ccc
ddd
1. Values in inches are converted from mm and rounded to 4 decimal digits.
2. A1 is defined as the distance from the seating plane to the lowest point on the package body.
3. Dimension “b” does not include dambar protrusion. Allowable dambar protrusion shall not cause the lead
width to exceed the maximum “b” dimension by more than 0.08 mm. Dambar cannot be located on the
lower radius or the foot. Minimum space between protrusion and an adjacent lead is 0.07 mm for 0.4 mm
and 0.5 mm pitch packages.
4. These dimensions apply to the flat section of the lead between 0.10 mm and 0.25 mm from the lead tip.
5. To be determined at seating datum plane C.
6. The Top package body size may be smaller than the bottom package size by as much as 0.15 mm.
7. Dimensions D1 and E1 do not include mold flash or protrusions. Allowable mold flash or protrusions is
“0.25 mm” per side. D1 and E1 are Maximum plastic body size dimensions including mold mismatch.
218/236
DS13314 Rev 3
STM32H733xG
Package information
8. “N” is the max number of terminal positions for the specified body size.
9. Dimensioning and tolerancing schemes conform to ASME Y14.5M-1994.
LQFP100 - Recommended footprint
75
76
51
50
0.5
0.3
16.7
14.3
100
26
1.2
1
25
12.3
16.7
1L_LQFP100_FP_V1
Dimensions are expressed in millimeters.
DS13314 Rev 3
219/236
233
Package information
STM32H733xG
Device marking for LQFP100
The following figure gives an example of topside marking versus pin 1 position identifier
location.
The printed markings may differ depending on the supply chain.
Other optional marking or inset/upset marks, which depend on supply chain operations, are
not indicated below.
Figure 66. LQFP100 marking example (package top view)
Product identification(1)
STM32H733
VGT6
Revision code
R
Date code
Y WW
Pin 1
indentifier
MSv52530V3
1. Parts marked as “ES”, “E” or accompanied by an Engineering Sample notification letter, are not yet
qualified and therefore not approved for use in production. ST is not responsible for any consequences
resulting from such use. In no event will ST be liable for the customer using any of these engineering
samples in production. ST’s Quality department must be contacted prior to any decision to use these
engineering samples to run a qualification activity.
220/236
DS13314 Rev 3
STM32H733xG
TFBGA100 package information
This TFBGA is 100 - ball, 8X8 mm, 0.8 mm pitch fine pitch ball grid array package.
ddd C
Figure 67. TFBGA100 - Outline
SEATING
PLANE
B
A1 ball
index
A1 ball
area
identifier
D1
e
A
A2
A1
C
F
G
D
E
A
B
C
D
E
F
G
H
J
K
E1
7.2
Package information
e
A
10 9 8 7 6 5 4 3 2 1
BOTTOM VIEW
b (100 BALLS)
eee
C A B
fff
C
TOP VIEW
A08Q_ME_V1
1. Drawing is not to scale.
DS13314 Rev 3
221/236
233
Package information
STM32H733xG
Table 122. TFBGA100 - Mechanical data
inches(1)
millimeters
Symbol
Min
Typ
Max
Min
Typ
Max
A
-
-
1.100
-
-
0.0433
A1
0.150
-
-
0.0059
-
-
A2
-
0.760
-
-
0.0299
-
b
0.350
0.400
0.450
0.0138
0.0157
0.0177
D
7.850
8.000
8.150
0.3091
0.3150
0.3209
D1
-
7.200
-
0.2835
-
E
7.850
8.000
8.150
0.3091
0.3150
0.3209
E1
-
7.200
-
-
0.2835
-
e
-
0.800
-
-
0.0315
-
F
-
0.400
-
-
0.0157
-
G
-
0.400
-
-
0.0157
-
ddd
-
-
0.100
-
-
0.0039
eee
-
-
0.150
-
-
0.0059
fff
-
-
0.080
-
-
0.0031
1. Values in inches are converted from mm and rounded to 4 decimal digits.
Figure 68. TFBGA100 - Recommended footprint
Dpad
Dsm
BGA_WLCSP_FT_V1
1. Dimensions are expressed in millimeters.
222/236
DS13314 Rev 3
STM32H733xG
Package information
Table 123. TFBGA100 - Recommended PCB design rules (0.8 mm pitch BGA)
Dimension
Recommended values
Pitch
0.8
Dpad
0.400 mm
Dsm
0.470 mm typ (depends on the soldermask
registration tolerance)
Stencil opening
0.400 mm
Stencil thickness
Between 0.100 mm and 0.125 mm
Pad trace width
0.120 mm
Device marking for TFBGA100
The following figure gives an example of topside marking versus pin 1 position identifier
location.
The printed markings may differ depending on the supply chain.
Other optional marking or inset/upset marks, which depend on supply chain operations, are
not indicated below.
Figure 69. TFBGA100 marking example (package top view)
Product
identification(1)
STM32H733
Revision code
VGH6
R
Date code
Y
Ball
A1identifier
WW
MSv52531V2
1. Parts marked as “ES”, “E” or accompanied by an Engineering Sample notification letter, are not yet
qualified and therefore not approved for use in production. ST is not responsible for any consequences
resulting from such use. In no event will ST be liable for the customer using any of these engineering
samples in production. ST’s Quality department must be contacted prior to any decision to use these
engineering samples to run a qualification activity.
DS13314 Rev 3
223/236
233
Package information
7.3
STM32H733xG
LQFP144 package information
This LQFP is a 144-pin, 20 x 20 mm low-profile quad flat package.
Figure 70. LQFP144 - Outline
SEATING
PLANE
c
A1
A2
A
C
0.25 mm
GAUGE PLANE
D
L
D1
K
A1
ccc C
L1
D3
108
73
109
E
37
144
PIN 1
E1
E3
b
72
1
36
IDENTIFICATION
e
1A_ME_V4
1. Drawing is not to scale.
224/236
DS13314 Rev 3
STM32H733xG
Package information
Table 124. LQFP144 - Mechanical data
inches(1)
millimeters
Symbol
Min
Typ
Max
Min
Typ
Max
A
-
-
1.600
-
-
0.0630
A1
0.050
-
0.150
0.0020
-
0.0059
A2
1.350
1.400
1.450
0.0531
0.0551
0.0571
b
0.170
0.220
0.270
0.0067
0.0087
0.0106
c
0.090
-
0.200
0.0035
-
0.0079
D
21.800
22.000
22.200
0.8583
0.8661
0.8740
D1
19.800
20.000
20.200
0.7795
0.7874
0.7953
D3
-
17.500
-
-
0.6890
-
E
21.800
22.000
22.200
0.8583
0.8661
0.8740
E1
19.800
20.000
20.200
0.7795
0.7874
0.7953
E3
-
17.500
-
-
0.6890
-
e
-
0.500
-
-
0.0197
-
L
0.450
0.600
0.750
0.0177
0.0236
0.0295
L1
-
1.000
-
-
0.0394
-
k
0°
3.5°
7°
0°
3.5°
7°
ccc
-
-
0.080
-
-
0.0031
1. Values in inches are converted from mm and rounded to 4 decimal digits.
DS13314 Rev 3
225/236
233
Package information
STM32H733xG
Figure 71. LQFP144 - Recommended footprint
108
109
73
1.35
72
0.35
0.5
19.9
17.85
22.6
144
37
1
36
19.9
22.6
ai14905e
1. Dimensions are expressed in millimeters.
226/236
DS13314 Rev 3
STM32H733xG
Package information
Device marking for LQFP144
The following figure gives an example of topside marking versus pin 1 position identifier
location.
The printed markings may differ depending on the supply chain.
Other optional marking or inset/upset marks, which depend on supply chain operations, are
not indicated below.
Figure 72. LQFP144 marking example (package top view)
Product
identification(1)
STM32H733ZGT6
Revision code
R
Date code
Y WW
Pin 1 identifier
MSv52532V2
1. Parts marked as “ES”, “E” or accompanied by an Engineering Sample notification letter, are not yet
qualified and therefore not approved for use in production. ST is not responsible for any consequences
resulting from such use. In no event will ST be liable for the customer using any of these engineering
samples in production. ST’s Quality department must be contacted prior to any decision to use these
engineering samples to run a qualification activity.
DS13314 Rev 3
227/236
233
Package information
7.4
STM32H733xG
UFBGA144 package information
This UFBGA is a 144-ball, 7 x 7 mm, 0.50 mm pitch, ultra fine pitch ball grid array package.
Figure 73. UFBGA144 - Outline
Z Seating plane
ddd Z
A4 A3 A2
A1 A
E1
e
A1 ball
A1 ball
identifier index area
F
X
E
A
F
D1
D
e
Y
M
12
1
BOTTOM VIEW
Øb (144 balls)
Ø eee M Z Y X
Ø fff M Z
TOP VIEW
A0AS_ME_V2
1. Drawing is not to scale.
Table 125. UFBGA144 - Mechanical data
inches(1)
millimeters
Symbol
228/236
Min.
Typ.
Max.
Min.
Typ.
Max.
A
0.460
0.530
0.600
0.0181
0.0209
0.0236
A1
0.050
0.080
0.110
0.0020
0.0031
0.0043
A2
0.400
0.450
0.500
0.0157
0.0177
0.0197
A3
-
0.130
-
-
0.0051
-
A4
0.270
0.320
0.370
0.0106
0.0126
0.0146
b
0.230
0.280
0.320
0.0091
0.0110
0.0126
D
6.950
7.000
7.050
0.2736
0.2756
0.2776
D1
5.450
5.500
5.550
0.2146
0.2165
0.2185
E
6.950
7.000
7.050
0.2736
0.2756
0.2776
E1
5.450
5.500
5.550
0.2146
0.2165
0.2185
e
-
0.500
-
-
0.0197
-
F
0.700
0.750
0.800
0.0276
0.0295
0.0315
DS13314 Rev 3
STM32H733xG
Package information
Table 125. UFBGA144 - Mechanical data (continued)
inches(1)
millimeters
Symbol
Min.
Typ.
Max.
Min.
Typ.
Max.
ddd
-
-
0.100
-
-
0.0039
eee
-
-
0.150
-
-
0.0059
fff
-
-
0.050
-
-
0.0020
1. Values in inches are converted from mm and rounded to 4 decimal digits.
Figure 74. UFBGA144 - Recommended footprint
Dpad
Dsm
BGA_WLCSP_FT_V1
Table 126. UFBGA144 - Recommended PCB design rules (0.50 mm pitch BGA)
Dimension
Recommended values
Pitch
0.50 mm
Dpad
0.280 mm
Dsm
0.370 mm typ. (depends on the soldermask
registration tolerance)
Stencil opening
0.280 mm
Stencil thickness
Between 0.100 mm and 0.125 mm
Pad trace width
0.120 mm
DS13314 Rev 3
229/236
233
Package information
STM32H733xG
Device marking for UFBGA144
The following figure gives an example of topside marking versus pin 1 position identifier
location.
The printed markings may differ depending on the supply chain.
Other optional marking or inset/upset marks, which depend on supply chain operations, are
not indicated below.
Figure 75. UFBGA144 marking example (package top view)
STM32H
Product identification(1)
733ZGI6
Revision code
Date code
Y
WW
R
Ball A1
identifier
MSv52533V2
1. Parts marked as “ES”, “E” or accompanied by an Engineering Sample notification letter, are not yet
qualified and therefore not approved for use in production. ST is not responsible for any consequences
resulting from such use. In no event will ST be liable for the customer using any of these engineering
samples in production. ST’s Quality department must be contacted prior to any decision to use these
engineering samples to run a qualification activity.
Note:
230/236
DS13314 Rev 3
STM32H733xG
7.5
Package information
Thermal characteristics
The maximum chip-junction temperature, TJ max, in degrees Celsius, may be calculated
using the following equation:
TJ max = TA max + (PD max × ΘJA)
Where:
•
TA max is the maximum ambient temperature in °C,
•
ΘJA is the package junction-to-ambient thermal resistance, in °C/W,
•
PD max is the sum of PINT max and PI/O max (PD max = PINT max + PI/Omax),
•
PINT max is the product of IDD and VDD, expressed in Watts. This is the maximum chip
internal power.
PI/O max represents the maximum power dissipation on output pins where:
PI/O max = Σ (VOL × IOL) + Σ((VDD – VOH) × IOH),
taking into account the actual VOL / IOL and VOH / IOH of the I/Os at low and high level in the
application.
Table 127. Thermal characteristics
Symbol
ΘJA
ΘJB
ΘJC
Definition
Thermal resistance
junction-ambient
Thermal resistance
junction-board
Thermal resistance
junction-case
Parameter
Value
Thermal resistance junction-ambient
LQFP100 - 14 x 14 mm /0.5 mm pitch
43.8
Thermal resistance junction-ambient
TFBGA100 - 8 x 8 mm /0.8 mm pitch
43.2
Thermal resistance junction-ambient
LQFP144 - 20 x 20 mm /0.5 mm pitch
44.8
Thermal resistance junction-ambient
UFBGA144 - 7 x 7 mm /0.5 mm pitch
TBD
Thermal resistance junction-ambient
LQFP100 - 14 x 14 mm /0.5 mm pitch
19.8
Thermal resistance junction-ambient
TFBGA100 - 8 x 8 mm /0.8 mm pitch
24.8
Thermal resistance junction-ambient
LQFP144 - 20 x 20 mm /0.5 mm pitch
24.4
Thermal resistance junction-ambient
UFBGA144 - 7 x 7 mm /0.5 mm pitch
TBD
Thermal resistance junction-ambient
LQFP100 - 14 x 14 mm /0.5 mm pitch
7.3
Thermal resistance junction-ambient
TFBGA100 - 8 x 8 mm /0.8 mm pitch
13.2
Thermal resistance junction-ambient
LQFP144 - 20 x 20 mm /0.5 mm pitch
7.4
Thermal resistance junction-ambient
UFBGA144 - 7 x 7 mm /0.5 mm pitch
TBD
DS13314 Rev 3
Unit
°C/W
°C/W
°C/W
231/236
233
Package information
7.5.1
232/236
STM32H733xG
Reference documents
•
JESD51-2 Integrated Circuits Thermal Test Method Environment Conditions - Natural
Convection (Still Air). Available from www.jedec.org.
•
For information on thermal management, refer to application note “Thermal
management guidelines for STM32 applications” (AN5036) available from www.st.com.
DS13314 Rev 3
STM32H733xG
8
Ordering information
Ordering information
Example:
STM32 H
733
V
G
T
6
TR
Device family
STM32 = Arm-based 32-bit microcontroller
Product type
H = High performance
Device subfamily
733 = STM32H733
Pin count
V = 100 pins
Z = 144 pins
Flash memory size
G = 1024 Kbytes
Package
T = LQFP ECOPACK2
I = UFBGA pitch 0.5 mm ECOPACK2
H = TFBGA ECOPACK2
Temperature range
6 = Industrial temperature range –40 to 85 °C
Packing
TR = tape and reel
No character = tray or tube
For a list of available options (speed, package, etc.) or for further information on any aspect
of this device, please contact your nearest ST sales office.
DS13314 Rev 3
233/236
233
Revision history
9
STM32H733xG
Revision history
Table 128. Document revision history
Date
Revision
10-Jul-2020
1
Initial release.
2
Renamed Section 3.31 into True random number generator (RNG).
Replaced VDDIOx by VDD in Section 6: Electrical characteristics.
Updated IIO in Table 10: Current characteristics.
Updated Table 24: Typical current consumption in Autonomous mode,
Table 27: Typical and maximum current consumption in Standby mode and
Table 28: Typical and maximum current consumption in VBAT mode.
Added Section 6.3.15: I/O current injection characteristics.
Removed reference to PI8 in Table 52: Output voltage characteristics for all
I/Os except PC13, PC14 and PC15 and Table 53: Output voltage
characteristics for PC13, PC14 and PC15.
Added Section : Analog switch between ports Pxy_C and Pxy.
03-Sep-2020
Changes
Added indication that patents apply to the devices in Section : Features.
Added reference to errata sheet in Section 1: Introduction.
Table 1: STM32H733xG features and peripheral counts:
– Changed number of general-purpose 32-bit timers to 4.
– For LQFP100 and TFBGA100 packages, replaced 2 Octo-SPI/Quad-SPI
interfaces by 1 and remove note.
In Section 3.8.1: Power supply scheme, changed VDD power supply
requirements.
Changed USART communication speed to 17 Mbit/s in Section 3.37:
Universal synchronous/asynchronous receiver transmitter (USART).
10-Dec-2021
3
Table 7: STM32H733 pin and ball descriptions:
– Added Note 1. to the package pin/balls corresponding to Pxy_C.
– For PA15(JTDI), replaced SPI3_NSS/I2S3_WS aternate function by
SPI3_NSS(boot)/I2S3_WS.
Moved LSI clock from backup domain to VDD domain in Figure 10: Power
supply scheme.
Added VBAT in Table 12: General operating conditions.
Updated Table 15: Operating conditions at power-up/power-down title and
added tVCORE.
Updated measurement conditions for Typical and maximum current
consumption.
Section : On-chip peripheral current consumption: updated measurement
conditions and Table 29: Peripheral current consumption in Run mode.
Updated Table 31: High-speed external user clock characteristics.
Renamed ILEAK parameter into Ilkg in Table 51: I/O static characteristics.
234/236
DS13314 Rev 3
STM32H733xG
Revision history
Table 128. Document revision history
Date
Revision
Changes
Updated Table 31: High-speed external user clock characteristics.
Changed unit for PLL long-term jitter in Table 39: PLL1 characteristics (wide
VCO frequency range).
Renamed ILEAK into Ikg in Table 51: I/O static characteristics
Table 55: Output timing characteristics (HSLV ON): updated load
capacitance condition for tr/tf and for speed = 10.
Updated Figure 32: OCTOSPI SDR read/write timing diagram, Figure 33:
OCTOSPI DTR mode timing diagram, Figure 34: OCTOSPI Hyperbus clock
timing diagram, Figure 35: OCTOSPI Hyperbus read timing diagram and
Figure 36: OCTOSPI Hyperbus write timing diagram.
10-Dec-2021
3 (continued)
Updated sampling rate fro slow channels in Table 80: 16-bit ADC
characteristics.
Updated Figure 37: ADC accuracy characteristics and Figure 38: Typical
connection diagram when using the ADC with FT/TT pins featuring analog
switch function as we as notes below figure.
Table 89: Temperature sensor characteristics updated TL max value.
Changed temperature condition to 130 °C for TS_CAL2 in Table 90:
Temperature sensor calibration values.
Updated Figure 39: Power supply and reference decoupling (VREF+ not
connected to VDDA)
Updated Figure 46: USART timing diagram in Master mode and Figure 47:
USART timing diagram in Slave mode.
Updated Figure 56: SD high-speed mode, Figure 57: SD default mode and
Figure 58: SDMMC DDR mode.
Updated Figure 62: Ethernet MII timing diagram.
Updated Figure 65: LQFP100- Outline, Table 121: LQFP100 - Mechanical
data, and Figure 68: TFBGA100 - Recommended footprint.
DS13314 Rev 3
235/236
235
STM32H733xG
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and
improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on
ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order
acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or
the design of Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. For additional information about ST trademarks, please refer to www.st.com/trademarks. All other
product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2021 STMicroelectronics – All rights reserved
236/236
DS13314 Rev 3
">