STMicroelectronics TSV994 Datasheet
Reklam
Reklam
TSV991, TSV992, TSV994 TSV991A
TSV992A, TSV994A
Datasheet
Rail-to-rail input/output 20 MHz GBP operational amplifiers
SOT23-5
Pin connections
(top view)
D F N 8 x 2
DFN6 1.3x1.6x0.55
IN-
1
IN+
2
NC
3
6
VCC+
5
VCC-
4
OUT
MiniSO8, SO8, DFN8 2x2
SO14, TSSOP14
Product status link
TSV991 , TSV992 , TSV994 , TSV991A ,
TSV992A , TSV994A
Related products
See TSV911 ,
TSV912 , TSV914 ,
TSV911A ,
TSV912A ,
TSV914A
For unity-gain stable amplifiers
Features
• Low input offset voltage: 1.5 mV max. (A grade)
• Rail-to-rail input and output
• Wide bandwidth 20 MHz
• Stable for gain ≥ 4 or ≤ -3
• Low power consumption: 820 µA typ.
• High output current: 35 mA
• Operating from 2.5 V to 5.5 V
• Low input bias current, 1 pA typ.
• ESD internal protection ≥ 5 kV
Applications
• Battery-powered applications
• Portable devices
• Signal conditioning and active filtering
• Medical instrumentation
• Automotive applications
Description
The TSV99x and TSV99xA family of single, dual, and quad operational amplifiers offers low voltage operation and rail-to-rail input and output. These devices feature an excellent speed/power consumption ratio, offering a 20 MHz gain-bandwidth, stable for gains above 4 (100 pF capacitive load), while consuming only 1.1 mA maximum at 5 V. They also feature an ultra-low input bias current. These characteristics make the TSV99x family ideal for sensor interfaces, battery-supplied and portable applications, as well as active filtering. These characteristics make the
TSV99x, TSV99xA family ideal for sensor interfaces, battery-supplied and portable applications, as well as active filtering.
DS4975 - Rev 14 - June 2019
For further information contact your local STMicroelectronics sales office.
www.st.com
1
TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A
Absolute maximum ratings and operating conditions
Absolute maximum ratings and operating conditions
Table 1. Absolute maximum ratings (AMR)
Symbol
V
CC
V id
V in
I in
T stg
T j
R thja
R thjc
Input current
Storage temperature
Parameter
Thermal resistance junction to
Thermal resistance junction to case
Value
±V
6
CC
(V
CC-
) - 0.2 to (V
CC+
10
-65 to 150
) + 0.2
Unit
V mA
Maximum junction temperature
DFN8 2x2
DFN6 1.3x1.6x0.55
SOT23-5
SO8
MiniSO8
SO14
TSSOP14
SOT23-5
SO8
MiniSO8
SO14
TSSOP14
125
190
103
100
81
40
39
31
32
150
57
230
250
°C
°C/W
HBM: human body model
MM: machine model
5
400 kV
SOT23-5, SO8, MiniSO8,
DFN8 2x2
DFN6 1.3x1.6x0.55
TSSOP14
SO14
1500
ESD
CDM: charged device model
TBD
750
500
200
V
Latch-up immunity mA
1. Value is with respect to the V
CC-
pin.
2. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal.
3. V
CC
- V
IN
must not exceed 6 V.
4. Input current must be limited by a resistor in series with the inputs.
5. Short-circuits can cause excessive heating and destructive dissipation.
6. R th
are typical values.
7. Human body model: 100 pF discharged through a 1.5 kΩ resistor between two pins of the device, done for all couples of pin combinations with other pins floating.
8. Machine model: 200 pF charged to the specified voltage, then discharged directly between two pins of the device with no external series resistor (internal resistor < 5 Ω), done for all couples of pin combinations with other pins floating.
9. Charged device model: all pins plus packages are charged together to the specified voltage and then discharged directly to the ground.
DS4975 - Rev 14 page 2/28
Symbol
V
CC
V icm
T op
TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A
Absolute maximum ratings and operating conditions
Table 2. Operating conditions
Parameter
Supply voltage
Common mode input voltage range
Operating free air temperature range
Value
2.5 to 5.5
(V
CC-
) - 0.1 to (V
CC+
) + 0.1
-40 to 125
Unit
V
°C
DS4975 - Rev 14 page 3/28
TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A
Electrical characteristics
2 Electrical characteristics
Note: In the electrical characteristic tables below, all parameter limits at temperatures other than 25 °C are guaranteed by correlation.
Table 3. Electrical characteristics at V
CC+
= 2.5 V, V
CC-
= 0 V, V icm
= V
CC
/2, with R
L
connected to V
CC
/2, full temperature range (unless otherwise specified)
Symbol Min.
Typ.
Max.
Unit
V io
∆V io
/∆T
I io
I ib
CMR
A vd
V
CC
- V
OH
V
OL
I out
I
CC
GBP
Gain
Parameter
Offset voltage, TSV99x
Offset voltage, TSV99xA
Conditions
DC performance
T op
= 25 °C
T min
< T op
< T max
T op
= 25 °C
T min
< T op
< T max
Input offset voltage drift
Input offset current,
V out
= V
CC
Input bias current, V out
= V
CC
/2
Common mode rejection ratio,
20 log (ΔV ic
/ΔV io
)
Large signal voltage gain
High-level output voltage
Low-level output voltage
I
I sink source
Supply current (per channel)
Gain bandwidth product
Minimum gain for stability
T op
= 25 °C
T min
< T op
< T max
T op
= 25 °C
T min
< T op
< T max
0 V to 2.5 V, V out
= 1.25 V, T op
= 25 °C
T min
< T op
< T max
R
L
= 10 kΩ, V out
= 0.5 V to 2 V,
T op
= 25 °C
T min
< T op
< T max
R
L
= 10 kΩ, T min
< T op
< T max
R
L
= 600 Ω, T min
< T op
< T max
R
L
= 10 kΩ, T min
< T op
< T max
R
L
= 600 Ω, T min
< T op
< T max
V o
= 2.5 V, T op
= 25 °C
T min
< T op
< T max
V o
= 0 V, T op
= 25 °C
T min
< T op
< T max
No load, V out
= V
CC
/2, T min
T max
< T op
<
AC performance
R
L
= 2 kΩ, C
L
= 100 pF, f = 100 kHz,
T op
= 25 °C
Phase margin = 45 °, R f
= 10 kΩ,
R
L
= 2 kΩ, C
L
= 100 pF, T op
= 25 °C, positive gain configuration
58
53
80
75
18
16
18
16
0.1
1
75
89
15
45
15
45
32
2
1
35
0.78
20
4
40
150
40
150
10
100
10
100
4.5
7.5
1.5
3
1.1
mV
μV/°C pA dB mV mA
MHz
V/V
DS4975 - Rev 14 page 4/28
TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A
Electrical characteristics
Symbol
Gain
SR e n
THD+N
Parameter
Minimum gain for stability
Slew rate
Equivalent input noise voltage
Total harmonic distortion
Conditions
Phase margin = 45 °, R f
= 10 kΩ,
R
L
= 2 kΩ, C
L
= 100 pF, T op
= 25 °C, negative gain configuration
R
L
= 2 kΩ, C
L
= 100 pF, T op
= 25 °C f = 10 kHz, T op
= 25 °C
G = -3, f = 1 kHz, R
L
= 2 kΩ, Bw = 22 kHz, V icm
= V
CC
/2, V out
= 2 V pp
,
T op
=25 °C
1. Guaranteed by design
Min.
Typ.
-3
10
21
0.0025
Max.
Unit
V/V
V/μs nV/√Hz
%
Table 4. Electrical characteristics at V
CC+
= 3.3 V, V
CC-
= 0 V, V icm
= V
CC
/2, with R
L
connected to V
CC
/2, full temperature range (unless otherwise specified)
Symbol Min.
Typ.
Max.
Unit
V io
∆V io
/∆T
I io
I ib
CMR
A vd
V
CC
- V
OH
V
OL
I out
I
CC
Parameter
Offset voltage, TSV99x
Offset voltage, TSV99xA
Conditions
DC performance
T op
= 25 °C
T min
< T op
< T max
T op
= 25 °C
T min
< T op
< T max
Input offset voltage drift
Input offset current,
V out
= V
CC
Input bias current, V out
= V
CC
/2
Common mode rejection ratio,
20 log (ΔV ic
/ΔV io
)
Large signal voltage gain
High-level output voltage
Low-level output voltage
I
I sink source
Supply current (per channel)
T op
= 25 °C
T min
< T op
< T max
T op
= 25 °C
T min
< T op
< T max
0 V to 3.3 V, V out
= 1.65 V, T op
= 25 °C
T min
< T op
< T max
R
L
= 10 kΩ, V out
= 0.5 V to 2.8 V,
T op
= 25 °C
T min
< T op
< T max
R
L
= 10 kΩ, T min
< T op
< T max
R
L
= 600 Ω, T min
< T op
< T max
R
L
= 10 kΩ, T min
< T op
< T max
R
L
= 600 Ω, T min
< T op
< T max
V o
= 3.3 V, T op
= 25 °C
T min
< T op
< T max
V o
= 0 V, T op
= 25 °C
T min
< T op
< T max
No load, V out
= V
CC
/2, T min
< T op
<
T max
AC performance
60
55
80
75
18
16
18
16
0.1
15
45
15
45
32
2
1
1
78
89
35
0.8
10
100
10
100
4.5
7.5
1.5
3
40
150
40
150
1.1
mV
μV/°C pA dB mV mA
DS4975 - Rev 14 page 5/28
TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A
Electrical characteristics
Symbol
GBP
Gain
SR e n
THD+N
Parameter
Gain bandwidth product
Minimum gain for stability
Slew rate
Equivalent input noise voltage
Total harmonic distortion
Conditions
R
L
= 2 kΩ, C
L
= 100 pF, f = 100 kHz,
T op
= 25 °C
Phase margin = 45 °, R f
= 10 kΩ,
R
L
= 2 kΩ, C
L
= 100 pF, T op
= 25 °C, positive gain configuration
Phase margin = 45 °, R f
= 10 kΩ,
R
L
= 2 kΩ, C
L
= 100 pF, T op
= 25 °C, negative gain configuration
R
L
= 2 kΩ, C
L
= 100 pF, f = 100 kHz,
T op
= 25 °C f = 10 kHz, T op
= 25 °C
G = -3, f = 1 kHz, R
L
= 2 kΩ, Bw = 22 kHz, V icm
= V
CC
/2, V out
= 2.8 V pp
,
T op
= 25 °C
1. Guaranteed by design.
Min.
Typ.
20
4
-3
10
21
0.0018
Max.
Unit
MHz
V/V
V/μs nV/√Hz
%
Table 5. Electrical characteristics at V
CC+
= 5 V, V
CC-
= 0 V, V icm
= V
CC
/2, with R range (unless otherwise specified)
L
connected to V
CC
/2, full temperature
Symbol Parameter Min.
Typ.
Max.
Unit
V io
Offset voltage, TSV99x
Offset voltage, TSV99xA
Conditions
DC performance
T op
= 25 °C
T min
< T op
< T max
T op
= 25 °C
T min
< T op
< T max
0.1
4.5
7.5
1.5
3 mV
∆V io
/∆T Input offset voltage drift 2
1
μV/°C
I io
I ib
CMR
Input offset current,
V out
= V
CC
/2
Input bias current, V out
= V
CC
/2
Common mode rejection ratio,
20 log (ΔV ic
/ΔV io
)
T op
= 25 °C
T min
< T op
< T max
T op
= 25 °C
T min
< T op
< T max
0 V to 5 V, V out
= 2.5 V,
T op
= 25 °C
T min
< T op
< T max
62
57
1
82
10
100
10
100 pA
SVR
Supply voltage rejection ratio,
20 log (ΔV cc
/ΔV io
)
V
CC
= 2.5 V to 5 V 70 86 dB
A vd
V
CC
- V
OH
V
OL
Large signal voltage gain
High-level output voltage
Low-level output voltage
R
L
= 10 kΩ, V out
= 0.5 V to 4.5 V,
T op
= 25 °C
T min
< T op
< T max
R
L
= 10 kΩ, T min
< T op
< T max
R
L
= 600 Ω, T min
< T op
< T max
R
L
= 10 kΩ, T min
< T op
< T max
R
L
= 600 Ω, T min
< T op
< T max
80
75
91
15
45
15
45
40
150
40
150 mV
DS4975 - Rev 14 page 6/28
TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A
Electrical characteristics
Symbol
I
I out
CC
GBP
Gain
SR e n
THD+N
Parameter
I
I sink source
Supply current (per channel)
Gain bandwidth product
Minimum gain for stability
Slew rate
Equivalent input noise voltage
Total harmonic distortion
Conditions
V o
= 5 V, T op
= 25 °C
T min
< T op
< T max
V o
= 0 V, T op
= 25 °C
T min
< T op
< T max
No load, V out
= 2.5 V, T min
T max
< T op
<
AC performance
R
L
= 2 kΩ, C
L
= 100 pF, f = 100 kHz,
T op
= 25 °C
Phase margin = 45 °, R f
= 10 kΩ,
R
L
= 2 kΩ, C
L
= 100 pF, T op
= 25 °C, positive gain configuration
Phase margin = 45 °, R f
= 10 kΩ,
R
L
= 2 kΩ, C
L
= 100 pF, T op
=25 °C, negative gain configuration
R
L
= 2 kΩ, C
L
= 100 pF, f = 100 kHz,
T op
= 25 °C f = 10 kHz, T op
= 25 °C
G = -3, f = 1 kHz, R
L
= 2 kΩ, Bw = 22 kHz, V icm
= V
CC
/2, V out
= 4.4 V pp
,
T op
= 25 °C
1. Guaranteed by design.
Min.
18
16
18
16
Typ.
32
35
0.82
20
4
-3
10
21
0.0014
Max.
1.1
Unit mA
MHz
V/V
V/μs nV/√Hz
%
DS4975 - Rev 14 page 7/28
TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A
Electrical characteristic curves
3 Electrical characteristic curves
Figure 1. Input offset voltage distribution at T = 25 °C
140
120
100
80
60
40
20
0
-5
Vcc= 5V
Vicm =2.5V
Ta mb =25 ° C
-4 -3 -2 -1 0 1 2
Input o ffs et Vo ltag e (mV)
3 4 5
Figure 2. Input offset voltage distribution at T = 125 °C
40
°
30
20
10
0
-5 -4 -3 -2 -1 0 1 2
Input o ffs et Vo ltag e (mV)
3 4 5
Figure 3. Supply current vs. input common-mode voltage at V
CC
= 2.5 V
Figure 4. Supply current vs. input common-mode voltage at V
CC
= 5 V
Figure 5. Output current vs. output voltage at V
CC
= 2.5 V Figure 6. Output current vs. output voltage at V
CC
= 5 V
DS4975 - Rev 14 page 8/28
TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A
Electrical characteristic curves
Figure 7. Voltage gain and phase vs. frequency at V
CC
= 5
V and V icm
= 0.5 V
Figure 8. Voltage gain and phase vs. frequency at V
CC
= 5
V and V icm
= 2.5 V
Figure 9. Positive slew rate Figure 10. Negative slew rate
Vin : from 0.5V to Vcc- 0.5V
S R : ca lculat ed from 10% to 90%
Vin : from 0.5V to Vcc- 0.5V
S R : ca lculat ed from 10 % to 90 %
Figure 11. Distortion + noise vs. frequency Figure 12. Distortion + noise vs. output voltage
DS4975 - Rev 14 page 9/28
Figure 13. Noise vs. frequency
TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A
Electrical characteristic curves
Figure 14. Supply current vs. supply voltage
DS4975 - Rev 14 page 10/28
TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A
Application information
4 Application information
4.1
Driving resistive and capacitive loads
These products are low-voltage, low-power operational amplifiers optimized to drive rather large resistive loads above 2 kΩ.
The TSV99x products are not unity gain stable. To ensure proper stability they must be used in a gain configuration, with a minimum gain of -3 or 4.
However, they can be used in a “ follower “ configuration by adding a small, in-series resistor at the output, which
value has been selected, the stability of the circuit should be tested on the bench and simulated with the simulation model.
Another way to improve stability and reduce peaking is to add a capacitor in parallel with the feedback resistor. As shown in
, the feedback capacitor drastically reduces the peaking versus capacitive load (inverting gain configuration, gain = -2).
Figure 15. In-series resistor vs. capacitive load when
TSV99x is used in follower configuration
Figure 16. Peaking versus capacitive load, with or without feedback capacitor in inverting gain configuration
4.2
4.3
PCB layouts
For correct operation, it is advised to add 10 nF decoupling capacitors as close as possible to the power supply pins.
Macromodel
An accurate macromodel of the TSV99x is available on STMicroelectronics’ web site at www.st.com. This model is a trade-off between accuracy and complexity (that is, time simulation) of the TSV99x operational amplifiers. It emulates the nominal performance of a typical device within the specified operating conditions mentioned in the datasheet. It helps to validate a design approach and to select the right operational amplifier, however, it does not replace on-board measurements.
DS4975 - Rev 14 page 11/28
5
TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A
Package information
Package information
In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: www.st.com
. ECOPACK is an ST trademark.
DS4975 - Rev 14 page 12/28
5.1
TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A
SOT23-5 package information
SOT23-5 package information
Figure 17. SOT23-5 package outline
DS4975 - Rev 14
Ref.
e
E
C
D
D1
F
L
K
A
A1
A2
B
Min.
0.90
0.90
0.35
0.09
2.80
2.60
1.50
0.10
0 degrees
1.05
0.40
0.15
2.90
1.90
0.95
2.80
1.60
0.35
Table 6. SOT23-5 mechanical data
Dimensions
Millimeters
Typ.
1.20
Max.
1.45
0.15
1.30
0.50
0.20
3.00
Min.
0.035
0.035
0.014
0.004
0.110
3.00
1.75
0.60
10 degrees
0.102
0.059
0.004
0 degrees
Inches
Typ.
0.047
0.041
0.016
0.006
0.114
0.075
0.037
0.110
0.063
0.014
0.118
0.069
0.024
10 degrees
Max.
0.057
0.006
0.051
0.020
0.008
0.118
page 13/28
5.2
TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A
DFN8 2 x 2 package information
DFN8 2 x 2 package information
Figure 18. DFN8 2 x 2 package outline
DS4975 - Rev 14
Ref.
A
A1
A3 b
D
D2
E
E2 e
L ddd
0.18
1.85
1.45
1.85
0.75
Min.
0.51
Table 7. DFN8 2 x 2 mechanical data
Dimensions
Millimeters
Typ.
0.55
Max.
0.60
0.05
Min.
0.020
0.15
0.25
2.00
1.60
2.00
0.90
0.50
0.30
2.15
1.70
2.15
1.00
0.007
0.073
0.057
0.073
0.030
0.425
0.08
Inches
Typ.
0.022
0.006
0.010
0.079
0.063
0.079
0.035
0.020
Max.
0.024
0.002
0.012
0.085
0.067
0.085
0.039
0.017
0.003
page 14/28
TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A
DFN8 2 x 2 package information
Figure 19. DFN8 2 x 2 recommended footprint
Note: The exposed pad of the DFN8 2x2 package is not internally connected. It can be set to ground or left floating.
DS4975 - Rev 14 page 15/28
5.3
TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A
DFN6 1.3 x 1.6 x 0.55 package information
DFN6 1.3 x 1.6 x 0.55 package information
Figure 20. DFN6 1.3 x 1.6 x 0.55 package outline
DS4975 - Rev 14 page 16/28
DS4975 - Rev 14
Ref.
E e
L
N aaa bbb ccc ddd eee
A
A1
A3
B
D
TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A
DFN6 1.3 x 1.6 x 0.55 package information
Min.
0.50
0.00
0.15
0.453
Table 8. DFN6 1.3 x 1.6 x 0.55 mechanical data
Dimensions
Millimeters
Typ.
1.60
0.40
0.553
6
0.05
0.07
0.10
0.05
0.08
0.55
0.02
0.15
0.20
1.30
Max.
0.60
0.05
0.25
0.653
Min.
0.020
0.000
0.006
0.018
Inches
Typ.
0.063
0.016
0.022
0.236
0.002
0.022
0.001
0.006
0.008
0.051
0.003
0.004
0.002
0.003
Figure 21. DFN6 1.3 x 1.6 x 0.55 recommended footprint
Max.
0.024
0.002
0.010
0.026
page 17/28
5.4
TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A
MiniSO8 package information
MiniSO8 package information
Figure 22. MiniSO8 package outline
DS4975 - Rev 14
Ref.
D
E
E1 e
L
L1
L2 k ccc
A
A1
A2 b c
Min.
0
0.75
0.22
0.08
2.80
4.65
2.80
0.40
0°
Table 9. MiniSO8 package mechanical data
Dimensions
Millimeters
Typ.
Min.
0.85
3.00
4.90
3.00
0.65
0.60
0.95
0.25
Max.
1.1
0.15
0.95
0.40
0.23
3.20
5.15
3.10
0.80
0
0.030
0.009
0.003
0.11
0.183
0.11
0.016
8°
0.10
0°
Inches
Typ.
0.033
0.118
0.193
0.118
0.026
0.024
0.037
0.010
Max.
0.043
0.0006
0.037
0.016
0.009
0.126
0.203
0.122
0.031
8°
0.004
page 18/28
5.5
TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A
SO8 package information
SO8 package information
Figure 23. SO8 package outline
DS4975 - Rev 14
Ref.
e h
L
E
E1
A
A1
A2 b c
D
L1 k ccc
Min.
0.10
1.25
0.28
0.17
4.80
5.80
3.80
0.25
0.40
0°
Table 10. SO8 package mechanical data
Dimensions
Millimeters
Typ.
Min.
Max.
1.75
0.25
4.90
6.00
3.90
1.27
0.48
0.23
5.00
6.20
4.00
0.004
0.049
0.011
0.007
0.189
0.228
0.150
0.50
1.27
0.010
0.016
1.04
8°
0.10
0°
Inches
Typ.
0.193
0.236
0.154
0.050
0.040
Max.
0.069
0.010
0.019
0.010
0.197
0.244
0.157
0.020
0.050
8°
0.004
page 19/28
5.6
TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A
SO14 package information
SO14 package information
Figure 24. SO14 package outline
DS4975 - Rev 14
Ref.
E e
H
C
D
A
A1
A2
B h
L k ddd
Min.
1.35
0.10
1.10
0.33
0.19
8.55
3.80
5.80
0.25
0.40
Table 11. SO14 package mechanical data
Dimensions
Millimeters
Typ.
Min.
Max.
1.75
1.75
0.25
1.65
0.51
0.25
8.75
4.0
0.05
0.004
0.04
0.01
0.007
0.33
0.15
1.27
6.20
0.50
1.27
0.22
0.009
0.015
8° (max.)
0.10
Inches
Typ.
0.05
Max.
0.069
0.068
0.009
0.06
0.02
0.009
0.34
0.15
0.24
0.02
0.05
0.004
page 20/28
5.7
TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A
TSSOP14 package information
TSSOP14 package information
Figure 25. TSSOP14 package outline aaa
DS4975 - Rev 14
Ref.
c
D
E
E1 e
A
A1
A2 b
L
L1 k aaa
Min.
0.05
0.80
0.19
0.09
4.90
6.20
4.30
0.45
0°
Table 12. TSSOP14 package mechanical data
Dimensions
Millimeters
Typ.
Min.
1.00
5.00
6.40
4.40
0.65
0.60
1.00
0.20
5.10
6.60
4.50
Max.
1.20
0.15
1.05
0.30
0.75
0.002
0.031
0.007
0.004
0.193
0.244
0.169
0.018
8°
0.10
0°
Inches
Typ.
0.004
0.039
0.197
0.252
0.173
0.0256
0.024
0.039
Max.
0.047
0.006
0.041
0.012
0.0089
0.201
0.260
0.176
0.030
8°
0.004
page 21/28
TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A
Ordering information
6
Note:
Ordering information
Table 13. Order code
Order code
TSV991ILT
TSV991AILT
TSV991IQ2T
TSV991AIQ2T
TSV991AIQ1T
TSV992IST
TSV992AIST
TSV992IDT
TSV992AIDT
TSV992IQ2T
TSV994IPT
TSV994AIPT
TSV994IDT
TSV994AIDT
TSV992IYDT
TSV992AIYDT
TSV994IYDT
TSV994AIYDT
Temperature range
-40 °C to 125 °C
-40 °C to 125 °C automotive grade
Package
SOT23-5
DFN8 2x2
DFN6 1.3x1.6x0.55
MiniSO8
SO8
DFN8 2x2
TSSOP14
SO14
SOT23-5
SO8
MiniSO8
SO14
TSSOP14
Packing
Tape and reel
1. Qualified and characterized according to AEC Q100 and Q003 or equivalent, advanced screening according to AEC Q001 &
Q 002 or equivalent.
Marking
K130
K129
K1F
K1E
K5
K132
K135
V992I
V992AI
K38
V994I
V994AI
V994I
V994AI
K149
K150
V992IY
V992AY
K149
K150
V994IY
V994AY
V994IY
V994AY
In the table above, all packages except the SO14 are "moisture sensitivity level 1" as per JEDEC J-STD-020-C.
SO14 is JEDEC level 3.
DS4975 - Rev 14 page 22/28
TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A
Revision history
Date
31-Jul-2006
07-Nov-2006
12-Dec-2006
07-Jun-2007
11-Feb-2008
25-May-2009
19-Oct-2009
14-Jan-2010
22-Oct-2012
22-Oct-2012
10-Mar-2014
12-Jun-2015
Revision
1
2
3
4
5
6
7
8
9
9 cont’d
10
11
Table 14. Document revision history
Changes
Preliminary data release for product under development.
Final version of datasheet.
Noise and distortion figures added.
ESD tolerance modified for SO14, CDM in Table 1: "Absolute maximum ratings
(AMR)".
Automotive grade commercial products added in Table 13: "Order codes".
Note about SO14 added in Table 13: "Order codes".
Limits in temperature added in Section 2: "Electrical characteristics".
Corrected MiniSO8 package information.
Corrected footnote for automotive grade order codes in order code table.
Improved presentation of package information.
Added input current information in Table 1: "Absolute maximum ratings (AMR)".
Added Section 3: "Application information".
Updated all packages in Section 4: "Package information".
Added new order codes: TSV991IYLT, TSV991AIYLT, TSV992IYST, TSV992AIYST,
TSV994IYPT, TSV994AIYPT in Table 13: "Order codes".
Added A versions of devices in title on cover page.
Added parameters for full temperature range in Table 3, Table 4, and Table 5.
Removed gain margin and phase margin parameters in Table 3, Table 4, and Table 5.
These parameters have been replaced by the gain parameter (minimum gain for stability).
Added Figure 14 and Figure 16.
Added parameters for full temperature range in Table 3, Table 4, and Table 5.
Modified note relative to automotive grade in Table 13: "Order codes".
Document status changed to production data.
Modified gain value in Features and Description.
Added DFN8 2x2 pin connection diagram.
Table 1: "Absolute maximum ratings (AMR)": added package DFN8 2x2 to rows R thja and ESD.
Table 3, Table 4, and Table 5: replaced “DV io
” with ΔV io
/ΔT; modified “Gain” and “THD
+N” conditions and typical values.
Figure 7 and Figure 8: added arrows indicating “Gain” and ‘Phase”.
Figure 11 and Figure 12: updated.
Added Figure 18: "DFN8 2 x 2 mm (NB) package outline" and Figure 19: "DFN8 2 x 2 mm (NB) recommended footprint".
Table 13: "Order codes": updated automotive grade qualification and added order code of DFN8 package.
Table 13: "Order codes": added new commercial product TSV991AIQ2T; corrected
“Marking” error for TSV991IQ2T from K1E to K1F.
Added DFN6 1.3 x 1.6 x 0.55 package for new order code TSV991AIQ1T.
Updated "L" dimension of Section 4: "DFN8 2 x 2 mm (NB) package information".
Updated min "k" value of Section 4.5: "SO8 package information".
DS4975 - Rev 14 page 23/28
TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A
Date
27-Nov-2015
03-Apr-2018
19-Jun-2019
Revision
12
13
14
Changes
Table 3, Table 4, and Table 5: modified that R
L and low-level output voltage parameters.
= 600 Ω (not 600 kΩ) for the high-level
Section 5.2: updated name of package and titles of drawings and table; added note about exposed pad.
Section 5.3: updated name of package.
Updated cover image and Table 13. Order code.
Updated the related product table in cover page.
DS4975 - Rev 14 page 24/28
TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A
Contents
Contents
DS4975 - Rev 14 page 25/28
TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A
List of tables
List of tables
Table 3. Electrical characteristics at V
Table 4. Electrical characteristics at V
Table 5. Electrical characteristics at V
DS4975 - Rev 14 page 26/28
TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A
List of figures
List of figures
Figure 3. Supply current vs. input common-mode voltage at V
= 2.5 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Figure 4. Supply current vs. input common-mode voltage at V
= 5 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Figure 5. Output current vs. output voltage at V
= 2.5 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Figure 6. Output current vs. output voltage at V
= 5 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Figure 7. Voltage gain and phase vs. frequency at V
= 0.5 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 8. Voltage gain and phase vs. frequency at V
= 2.5 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
DS4975 - Rev 14 page 27/28
TSV991, TSV992, TSV994 TSV991A, TSV992A, TSV994A
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of
Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. For additional information about ST trademarks, please refer to www.st.com/trademarks . All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2019 STMicroelectronics – All rights reserved
DS4975 - Rev 14 page 28/28
İndir
Herkese açık bağlantı güncellendi
Sohbetinize giden herkese açık bağlantı güncellendi. You may view and manage your chat links after registration here.
Belge herkese açık bağlantısı
Reklam