TDA7560
4 x 51 W quad bridge car radio amplifier
Datasheet
production data
Features
■
■
■
■
■
■
■
■
■
■
■
■
Superior output power capability:
– 4 x 51 W/4
max.
– 4 x 45 W/4
EIAJ
– 4 x 30 W/4
@ 14.4 V, 1 kHz, 10 %
– 4 x 80 W/2
max.
– 4 x 77 W/2
EIAJ
– 4 x 55 W/2
@ 14.4 V, 1 kHz, 10 %
Multipower BCD technology
MOSFET output power stage
Excellent 2
driving capability
Hi-Fi class distortion
Low output noise
Standby function
Mute function
Automute at min. supply voltage detection
Low external component count:
– Internally fixed gain (26 dB)
– No external compensation
– No bootstrap capacitors
On board 0.35 A high side driver
Protections:
– Output short circuit to GND, to V
S
, across the load
– Very inductive loads
Table 1.
Device summary
Order code
TDA7560
TDA7560H
Package
Flexiwatt25 (vertical)
Flexiwatt25 (horizontal)
'!0'03
Flexiwatt25
(vertical)
Flexiwatt25
(horizontal)
'!0'03
– Overrating chip temperature with soft thermal limiter
– Output DC offset detection
– Load dump voltage
– Fortuitous open GND
– Reversed battery
– ESD
Description
The TDA7560 is a breakthrough BCD (Bipolar /
CMOS / DMOS) technology class AB audio power amplifier in Flexiwatt 25 package designed for high power car radio.
The fully complementary P-Channel/N-Channel output structure allows a rail to rail output voltage swing which, combined with high output current and minimized saturation losses sets new power references in the car-radio field, with unparalleled distortion performances.
Packing
Tube
Tube
September 2013
This is information on a product in full production.
Doc ID 6886 Rev 6 1/17 www.st.com
1
4
5
1
2
Contents
Contents
3
TDA7560
Block and pin connection diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2
Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.3
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.4
Standard test and application circuit, and PCB layout . . . . . . . . . . . . . . . . 8
2.5
Electrical characteristics curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Application hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.1
SVR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.2
Input stage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.3
Standby and muting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.4
DC offset detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.5
Heatsink definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2/17 Doc ID 6886 Rev 6
TDA7560
List of tables
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Thermal data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Doc ID 6886 Rev 6 3/17
List of figures
List of figures
TDA7560
Figure 1.
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Figure 2.
Pins connection (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Figure 3.
Standard test and application circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Figure 4.
PCB and component layout of the
Figure 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 5.
Quiescent current vs. supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 6.
Output power vs. supply voltage (R
L
= 4
) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 7.
Output power vs. supply voltage (R
L
= 2
) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
= 4
). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 8.
Distortion vs. output power (R
L
Figure 9.
Figure 10.
Figure 11.
Distortion vs. output power (R
Distortion vs. frequency (R
Distortion vs. frequency (R
L
L
L
= 2
). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
= 4
) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
= 2
) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 12.
Crosstalk vs. frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 13.
Supply voltage rejection vs. frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 14.
Output attenuation vs. supply voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 15.
Output noise vs. source resistance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 16.
Power dissipation and efficiency vs. output power (sine-wave operation) . . . . . . . . . . . . . 11
Figure 17.
Figure 18.
Power dissipation vs. output power (music/speech simulation); R
Power dissipation vs. output power (music/speech simulation); R
L
L
= 4 x 4
= 4 x 2
Figure 19.
ITU R-ARM frequency response, weighting filter for transient pop. . . . . . . . . . . . . . . . . . . 12
Figure 20.
Flexiwatt25 (vertical) mechanical data and package dimensions . . . . . . . . . . . . . . . . . . . . 14
Figure 21.
Flexiwatt25 (horizontal) mechanical data and package dimensions. . . . . . . . . . . . . . . . . . 15
4/17 Doc ID 6886 Rev 6
TDA7560
1
Block and pin connection diagram
Block and pin connection diagram
Figure 1.
Block diagram
6CC
34"9
-54%
).
M &
).
M &
).
M &
).
M &
!#'.$
M &
362
M &
6CC
(3$
4!" 3'.$
M &
(3$6
/&&?$%4
/54
/54
07'.$
/54
/54
07'.$
/54
/54
07'.$
/54
/54
07'.$
N&
'!0'03
Figure 2.
Pins connection (top view)
/54
362
).
).
3'.$
).
).
!#'.$
4!"
0'.$
/54
34"9
/54
6
##
/54
0'.$
/54
0'.$
/54
6
##
/54
-54%
/54
0'.$
(3$
&LEXIWATT
VERTICAL
).
).
!#'.$
/54
0'.$
/54
6
##
/54
-54%
/54
0'.$
(3$
4!"
0'.$
/54
34"9
/54
6
##
/54
0'.$
/54
362
).
).
3'.$
&LEXIWATT
HORIZONTAL
Doc ID 6886 Rev 6
'!0'03
5/17
Electrical specifications TDA7560
2.1 Absolute maximum ratings
Table 2.
Symbol
Absolute maximum ratings
Parameter
V
CC
V
CC (DC)
V
CC (pk)
Operating supply voltage
DC supply voltage
Peak supply voltage (for t = 50 ms)
I
O
Output peak current
Repetitive (duty cycle 10 % at f = 10 Hz)
Non repetitive (t = 100 µs)
P tot
T j
T stg
Power dissipation T case
= 70 °C
Junction temperature
Storage temperature
Value
18
28
50
9
10
80
150
-55 to 150
Unit
V
V
V
A
A
W
°C
°C
Table 3.
Symbol
Thermal data
Parameter
R th j-case
Thermal resistance junction-to-case Max.
Value
1
Unit
°C/W
Refer to the test and application diagram, V
S
= 14.4 V; R
L
= 4
; R g
= 600
; f = 1 kHz; T amb
= 25 °C; unless otherwise specified.
Table 4.
Symbol
I q1
V
OS dV
OS
G v dG v
P o
Electrical characteristics
Parameter
Quiescent current
Output offset voltage
During mute ON/OFF output offset voltage
Voltage gain
Channel gain unbalance
-
Test condition
R
L
=
Play Mode
-
-
V
S
= 13.2 V; THD = 10 %
V
S
= 13.2 V; THD = 1 %
V
S
= 14.4 V; THD = 10 %
V
S
= 14.4 V; THD = 1 %
Min. Typ.
Max.
80
-
200
-
320
±50
-
25
-
23
16
28
20
-
26
-
25
19
30
23
±60
27
±1
-
Unit mA mV mV dB dB
W
6/17 Doc ID 6886 Rev 6
TDA7560
Table 4.
Symbol
P o
P o EIAJ
P o max.
e
No
Electrical characteristics (continued)
EIAJ output power
(1)
Max. output power
(1)
THD Distortion
Parameter Test condition
V
S
V
S
= 13.2 V; THD = 10 %, 2
= 13.2 V; THD = 1 %, 2
V
S
V
S
= 14.4 V; THD = 10 %, 2
= 14.4 V; THD = 1 %, 2
V
S
= 13.7 V; R
L
V
S
= 13.7 V; R
L
= 4
= 2
V
S
= 14.4 V; R
L
V
S
= 14.4 V; R
L
= 4
= 2
V
S
= 15.2 V; R
L
= 4
P o
= 4 W
P o
= 15 W; R
L
= 2
"A" Weighted
Bw = 20 Hz to 20 kHz
SVR Supply voltage rejection f ch
R i
High cut-off frequency
Input impedance f = 100 Hz; V r
= 1 Vrms
P
O
= 0.5 W
C
T
I
SB
I pin5
V
SB out
V
SB in
A
M
V
M out
V
M in
V
AM in
I pin22
Cross talk
Standby current consumption
Standby pin current
Standby out threshold voltage
Standby in threshold voltage
Mute attenuation
Mute out threshold voltage
Mute in threshold voltage
VS automute threshold
Muting pin current f = 1 kHz P
O
= 4 W f = 10 kHz P
O
= 4 W
V
ST-BY
= 1.5V
V
ST-BY
= 0 V
V
ST-BY
= 1.5 V to 3.5 V
(Amp: ON)
(Amp: OFF)
P
Oref
= 4W
(Amp: Play)
(Amp: Mute)
(Amp: Mute)
Att 80 dB; P
Oref
= 4 W
(Amp: Play)
Att < 0.1 dB; P
O
= 0.5 W
V
MUTE
= 1.5 V
(Sourced current)
V
MUTE
= 3.5 V
HSD section
V dropout
I prot
Dropout voltage
Current limits -
I
O
= 0.35 A; V
S
= 9 to 16 V
Electrical specifications
3.5
-
80
3.5
-
50
100
80
60
50
-
-
-
Min. Typ.
Max.
41
72
43
75
42
32
50
40
-
-
45
34
55
43
45
77
50
80
51
0.006
0.015
35
50
70
300
-
-
90
-
-
100
70
60
-
-
-
-
-
-
-
0.02
0.03
50
70
-
-
120
20
10
±10
-
1.5
-
-
1.5
Unit
W
W
W
%
A dB
V
V
A
V
V
µV dB kHz
K
dB
6.5
7
-5
7
7.5
12
-
8
18
18
V
A
A
-
400
0.25
-
0.6
800
V mA
Doc ID 6886 Rev 6 7/17
Electrical specifications
Table 4.
Symbol
Electrical characteristics (continued)
Parameter Test condition
Offset detector (Pin 25)
V
M_ON
V
M_OFF
V
OFF
Mute voltage for DC offset detection enabled
V
ST-BY
= 5 V
V
V
25_T
25_F
Detected differential output offset V
ST-BY
= 5 V; V mute
= 8 V
Pin 25 voltage for detection =
True
V
ST-BY
= 5 V; V mute
= 8 V
V
OFF
> ±4 V
Pin 25 voltage for detection =
False
V
ST-BY
= 5 V; V mute
= 8 V
V
OFF
> ±2 V
1.
Saturated square wave output.
2.4
8
-
±2
0
12
-
-
±3
-
-
-
6
±4
1.5
-
TDA7560
Min. Typ.
Max.
Unit
Standard test and application circuit, and PCB layout
Figure 3.
Standard test and application circuit
#
M &
#
M &
6CC 6CC
34"9
-54%
2
+
2
+
#
#
M &
#
M &
).
M &
).
# M &
).
# M &
).
# M & 3'.$
/54
/54
/54
/54
#
M &
362
#
M &
(3$/$
2
4!"
2K 7 TOBEPLACEDWHENPINISUSEDASOFFSETDETECTOR
'!0'03
V
V
V
V
V
8/17 Doc ID 6886 Rev 6
TDA7560
Figure 4.
PCB and component layout of the Figure 3 .
Components and top copper layer
Electrical specifications
Bottom copper layer
Doc ID 6886 Rev 6 9/17
Electrical specifications TDA7560
Figure 5.
Quiescent current vs. supply voltage
)DM!
6I
2,/HM
Figure 6.
Output power vs. supply voltage
(R
L
= 4
)
0O7
0OMAX
2,/HM
F+(Z
4($
4($
6S6
Figure 7.
Output power vs. supply voltage
(R
L
= 2
)
0O7
0OMAX
'!0'03
6S6
Figure 8.
Distortion vs. output power
(R
L
= 4
)
4($
6S6
2,/HM
2,/HM
F+(Z 4($
F+(Z
'!0'03
4($
F+(Z
6S6
Figure 9.
Distortion vs. output power
(R
L
= 2
)
4($
'!0'03
0O7
'!0'03
Figure 10. Distortion vs. frequency (R
L
= 4
)
4($
6S6
2,/HM
F+(Z
6S6
2,/HM
0O7
F+(Z
0O7 F(Z
10/17
'!0'03
Doc ID 6886 Rev 6
'!0'03
TDA7560 Electrical specifications
Figure 11. Distortion vs. frequency (R
L
= 2
) Figure 12. Crosstalk vs. frequency
4($ #2/334!,+D"
6S6
2,/HM
0O7
2,/HM
0O7
2G/HM
F(Z
Figure 13. Supply voltage rejection vs. frequency
362D"
'!0'03
F(Z
Figure 14. Output attenuation vs. supply voltage
'!0'03
/54!44. D"
2,/HM
0O7REF
2G/HM
6RIPPLE6RMS
F(Z
'!0'03
6S6
Figure 15. Output noise vs. source resistance Figure 16. Power dissipation and efficiency vs. output power (sine-wave operation)
'!0'03
%N6 0TOT7 H
H
6S6
2,/HM
6S6
2,X/HM
F+(Z3).%
+(ZLIN
!WGTD
0TOT
2G/HM
'!0'03
0O7
'!0'03
Doc ID 6886 Rev 6 11/17
Electrical specifications TDA7560
Figure 17. Power dissipation vs. output power
(music/speech simulation);
R
L
= 4 x 4
Figure 18. Power dissipation vs. output power
(music/speech simulation);
R
L
= 4 x 2
0TOT7
6S6
2,X/HM
'!533)!../)3%
#,)034!24
0TOT7
6S6
2,X/HM
'!533)!../)3%
#,)034!24
0O7
Figure 19. ITU R-ARM frequency response, weighting filter for transient pop
'!0'03
/UTPUTATTENUATIOND"
0O7
'!0'03
(Z
'!0'03
12/17 Doc ID 6886 Rev 6
TDA7560 Application hints
(ref. to the circuit of
Figure 3 )
3.1 SVR
Besides its contribution to the ripple rejection, the SVR capacitor governs the turn ON/OFF time sequence and, consequently, plays an essential role in the pop optimization during
ON/OFF transients.To conveniently serve both needs, ITS MINIMUM RECOMMENDED
VALUE IS 10 µF .
The TDA7560's inputs are ground-compatible and can stand very high input signals
(±8 Vpk) without any performances degradation.
If the standard value for the input capacitors (0.1µF) is adopted, the low frequency cut-off will amount to 16 Hz.
3.3 Standby muting
Standby and Muting facilities are both CMOS-compatible. In absence of true CMOS ports or microprocessors, a direct connection to Vs of these two pins is admissible but a 470 kOhm equivalent resistance should be present between the power supply and the muting and
ST-BY pins.
R-C cells have always to be used in order to smooth down the transitions for preventing any audible transient noises.
About the standby, the time constant to be assigned in order to obtain a virtually pop-free transition has to be slower than 2.5 V/ms.
The TDA7560 integrates a DC offset detector to avoid that an anomalous DC offset on the inputs of the amplifier may be multiplied by the gain and result in a dangerous large offset on the outputs which may lead to speakers damage for overheating. The feature is enabled by the MUTE pin (according to
Table 4
) and works with the amplifier unmuted and with no signal on the inputs.
The DC offset detection is signaled out on the HSD pin. To ensure the correct functionality of the Offset Detector it is necessary to connect a pulldown 10 k
resistor between HSD and ground.
Under normal usage (4 Ohm speakers) the heatsink's thermal requirements have to be deduced from
Figure 17
, which reports the simulated power dissipation when real music/speech programmes are played out. Noise with gaussian-distributed amplitude was employed for this simulation. Based on that, frequent clipping occurrence (worst-case) will cause P diss
= 26 W. Assuming T amb
= 70 °C and T
CHIP
= 150 °C as boundary conditions, the heatsink's thermal resistance should be approximately 2 °C/W. This would avoid any thermal shutdown occurrence even after long-term and full-volume operation
Doc ID 6886 Rev 6 13/17
Package information TDA7560
14/17
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK
®
packages, depending on their level of environmental compliance. ECOPACK
® specifications, grade definitions and product status are available at: www.st.com
.
ECOPACK
®
is an ST trademark.
Figure 20.
Flexiwatt25 (vertical) mechanical data and package dimensions
$)-
MM INCH
-).
490 -!8
-).
490 -!8
!
"
#
$
%
&
'
'
(
(
(
(
,
,
,
,
,
,
-
-
.
/
2
2
2
2
2
6
6
7\S
7\S
6
6
7\S
7\S
DAMBARPROTUSIONNOTINCLUDED
MOLDINGPROTUSIONINCLUDED
/54,).%!.$
-%#(!.)#!,$!4!
&LEXIWATTVERTICAL
6
#
"
6
(
(
6
(
2
(
!
2
6
.
2
2
, ,
6
6
0IN
' ' &
2
&,%8-%
,
2
2
-
2
%
-
$
'!0'03
Doc ID 6886 Rev 6
TDA7560 Package information
Figure 21.
Flexiwatt25 (horizontal) mechanical data and package dimensions
',0
PP
0,1 7<3
LQFK
0$; 0,1 7<3 0$;
$
(
)
*
*
+
+
+
+
%
&
'
/
/
/
/
/
/
1
3
5
5
/
0
0
0
5
5
5
9
9
9
9
7\S
7\S
7\S
7\S
'DPEDUSURWXVLRQQRWLQFOXGHG 0ROGLQJSURWXVLRQLQFOXGHG
287/,1($1'
0(&+$1,&$/'$7$
)OH[LZDWW
+RUL]RQWDO
9
9
+
+
+
5
+
5
1
5
5
9
9
9
$
0
* *
)
5
5
0
0
&
*$3*36
Doc ID 6886 Rev 6 15/17
Revision history TDA7560
Table 5.
Date
Document revision history
20-Dec-2001
10-Feb-2005
18-Sep-2008
07-Nov-2008
11-Sep-2012
16-Sep-2013
Revision
1
2
3
4
5
6
Changes
Initial release.
Improved value from 75 to 20mA of the “standby current
consumption” parameter in the Table 4: Electrical characteristics on page 6
.
Document reformatted.
Added new order code in Flexiwatt25 horizontal package.
Updated
Figure 3: Standard test and application circuit
.
Updated
Table 4: Electrical characteristics
.
Updated
Section 3.4: DC offset detector and Section 3.3: Standby and muting .
Added Figure 19: ITU R-ARM frequency response, weighting filter for transient pop .
Modified max. values of the V
OS
and THD parameter in Table 4:
Electrical characteristics .
Updated
Features on page 1
;
Updated
Section 2.3: Electrical characteristics
.
Updated Disclaimer.
16/17 Doc ID 6886 Rev 6
TDA7560
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE
SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B)
AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS
OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT
PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS
EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY
DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE
DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2013 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com
Doc ID 6886 Rev 6 17/17
