STMicroelectronics X-NUCLEO-OUT10A1 User Manual
Anuncio
Anuncio
UM2716
User manual
Getting started with X-NUCLEO-OUT10A1 industrial digital output expansion board for STM32 Nucleo
Introduction
The X-NUCLEO-OUT10A1 industrial digital output expansion board for STM32 Nucleo provides an affordable and easy-to-use solution for the development of 0.5 A (typ.) digital output modules, letting you easily evaluate the IPS161HF driving and diagnostic capabilities with industrial loads.
The X-NUCLEO-OUT10A1 interfaces with the microcontroller on the STM32 Nucleo via 3 kV optocouplers driven by GPIO pins and Arduino™ UNO R3 (default configuration) and ST morpho (optional, not mounted) connectors.
The expansion board should be connected to either a NUCLEO-F401RE or NUCLEO-G431RB development board, and can be stacked with another X-NUCLEO-OUT10A1 or an X-NUCLEO-OUT08A1 .
Two X-NUCLEO-OUT10A1 expansion boards allows you to evaluate a dual channel digital output module with 0.5 A (typ.) capability each, or a 0.5 A (typ.) single channel safety digital output module. In the second scenario, the first shield output is connected to the supply of the second one. Dedicated on-board hardware can be enabled or disabled to activate fast discharge of high capacitive loads, output voltage sensing and additional surge pulse output line protection.
Figure 1. X-NUCLEO-OUT10A1 expansion board
UM2716 - Rev 1 - June 2020
For further information contact your local STMicroelectronics sales office.
www.st.com
UM2716
Getting started
1
1.1
1.1.1
Getting started
Overview
•
•
•
•
•
•
•
•
•
•
•
The X-NUCLEO-OUT10A1 industrial digital output expansion board, embedding the IPS161HF intelligent power switch (IPS), is designed to meet the application requirement in terms of galvanic isolation between user interface
(or logic side) and power interface (or process side).
This requirement is satisfied by an optical isolation implemented through two couples of optocouplers:
1.
The first couple includes: a.
ISO1: for signal forwarding to the device and b.
ISO2: for diagnostic signal (DIAG pin) feedback
2.
The second couple incudes: a.
ISO3: for the additional output voltage feedback signal and b.
ISO4: for the additional circuitry driving Q1 to allow fast discharge of the output rail
The main features of the X-NUCLEO-OUT10A1 expansion board are:
• Based on IPS161HF single high-side switch with the following main features:
•
– Operating range up to 60 V/0.7 A
– Low power dissipation (R
ON(MAX)
= 120 mΩ)
– Fast decay for inductive loads
– Open load detection and diagnostics
– Overload and overheating protections with thermal shut-down and cut-off
– PowerSSO-12L package
Application board operating range: 12 - 33 V, 0 to 0.7 A
Extended voltage operating range (J1 open) up to 60 V
Green LED for output ON/OFF status
Red LED for diagnostics (open load, cut-off and overheating)
3 kV galvanic isolation
Supply rail reverse polarity protection
Ready for Safety Digital Output Architecture
EMC compliance according to IEC61000-4-2, IEC61000-4-3, IEC61000-4-5
Wide application development potential in STM32 Nucleo development environment
Equipped with Arduino™ UNO R3 connectors
CE certified
RoHS and China RoHS compliant
Digital section
The digital section is associated with the STM32 interface and digital supply voltage to and from the X-NUCLEO-
OUT10A1 expansion board.
The digital and power sections are isolated by 3.3 mm creepage. Communication between the two sections is guaranteed by ISO1, ISO2, ISO3 and ISO4 optocouplers.
UM2716 - Rev 1 page 2/16
Figure 2. X-NUCLEO-OUT10A1 expansion board: digital interface components
UM2716
Overview
1.1.2
The four Arduino ® UNO R3 connectors:
• allow expansion board communication with the peripheral and GPIO resources;
STM32 Nucleo development board accessing STM32
• provide digital supply voltage between the STM32 Nucleo development board and the X-NUCLEO-
OUT10A1 expansion board, in either direction.
Normally, the STM32 Nucleo development board supplies the expansion board by 3v3 or 5v0 (JP5 pins 1-2 closed) generated by the USB. You can select the preferred voltage on the expansion board via SW2 (3v3 by closing pins 1-2; 5v0 by closing pins 2-3).
Alternatively, it is possible to supply the STM32 Nucleo development board by the expansion board. In this case, an external supply voltage (7-12 V) should be connected to CN2 connector (not mounted by default) on the expansion board and the ground loop should be closed by mounting D2 (that enables reverse polarity protection) or by closing J3 (without reverse polarity).
•
•
To supply the V
IN
voltage rail is necessary to: close jumper JP5 between pins 2 and 3 and open jumper JP1 on the NUCLEO-F401RE open jumper JP5 between pins 1 and 2 and close jumper JP5 between pins 3 and 4 on the
G431RB
NUCLEO-
Power section
The power section involves the power supply voltage (CN1, pin 1 V
CC
, pin 2 GND), load connection (between
CN1 pin 3 and CN1 pin 2) and electromagnetic compatibility (EMC) protection (U2).
UM2716 - Rev 1 page 3/16
UM2716
Hardware requirements
Figure 3. X-NUCLEO-OUT10A1 expansion board: power stage components
1.2
For EMC:
•
•
• the transient voltage suppressor (U2), enabled by closing J1, is placed between V
CC
and GND tracks to protect the IPS161HF against surge discharge on the supply rail path up to ±1 kV/2Ω coupling; in common mode surge testing, two single-layer capacitors (C1 and C2 - not included) must be soledered at the predisposed locations; the IPS161HF output stages do not require additional EMC protections with respect to IEC61000-4-2 (± 10 kV contact, ±16 kV air), IEC61000-4-4 (± 4 kV), IEC61000-4-5 (± 3.5 kV) standards.
Hardware requirements
The X-NUCLEO-OUT10A1 expansion board is designed to be used with the NUCLEO-F401RE or NUCLEO-
G431RB STM32 Nucleo development boards.
To function correctly, the X-NUCLEO-OUT10A1 must be plugged onto the matching Arduino ® UNO R3 connector pins on the STM32 Nucleo board as shown below.
UM2716 - Rev 1 page 4/16
Figure 4. X-NUCLEO-OUT10A1 and STM32 Nucleo stack
UM2716
System requirements
1.3
1.4
System requirements
To use the STM32 Nucleo development boards with the X-NUCLEO-OUT10A1 expansion board, you need:
• a Windows PC/laptop (Windows 7 or above)
•
•
• a type A to mini-B USB cable to connect the STM32 Nucleo board to the PC when using a NUCLEO-
F401RE development board a type A to micro-B USB cable to connect the STM32 Nucleo board to the PC when using a NUCLEO-
G431RB development board the X-CUBE-OUT8 firmware and software package installed on your PC/laptop
Board setup
Step 1.
Connect the X-NUCLEO-OUT10A1 to the NUCLEO-F401RE or NUCLEO-G431RB development board through the Arduino connectors.
Step 2.
Connect the X-NUCLEO-OUT10A1
power section (see Section 1.1.2 Power section
).
Step 3.
Connect the load between CN1 pins 2 and 3.
Step 4.
Connect the mini-USB (for NUCLEO-F401RE ) or micro-USB (for NUCLEO-G431RB ) cable between your PC and the STM32 Nucleo board.
Step 5.
Download the selected firmware ( STSW-OUT8F4 for NUCLEO-F401RE or STSW-OUT8G4 for
NUCLEO-G431RB ) onto the microcontroller.
Step 6.
Provide the digital supply voltage (see
Section 1.1.1 Digital section ).
Step 7.
Reset the example sequence by pushing the black button on the STM32 Nucleo board.
UM2716 - Rev 1 page 5/16
UM2716
Board setup
Note:
Step 8.
Push the blue button on STM32 Nucleo board to choose among the examples provided in the default firmware package.
When using two boards stacked (e.g. dual channel digital output or single channel safety digital output application), you have to move some signal enabler resistors from DEFAULT to ALTERNATE position. You can refer to the expansion board schematic and/or to the table below (where board 0 mounts all the resistors in their
DEFAULT position).
IN1
R101
Table 1. Pin position when using a board stack
Nch_DRV
R102
Board 0
DIAG
R103
OUT_FB
R104
IN1
R111
Nch_DRV
R134
Board 1
DIAG
R112
OUT_FB
R131
UM2716 - Rev 1 page 6/16
2 Schematic diagrams
9
11
5
7
13
15
17
1
3
19
21
23
25
27
29
31
33
35
37
CN7
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
SSQ-119-04-L-D (N.M.)
Figure 5. X-NUCLEO-OUT10A1 circuit schematic (1 of 2)
Morpho Connectors
(N.M.)
5
7
9
11
1
3
13
15
17
19
21
23
25
27
29
31
33
35
37
CN10
28
30
32
34
20
22
24
26
36
38
2
4
6
8
10
12
14
16
18
SSQ-119-04-L-D (N.M.)
VCC
OUT1
Analog supply
8V - 60 V
TP8
5001
+ C8
47uF (N.M.)
J2 default open
C3
2.2uF
J1 default closed
U2
SM15T39CA
EARTH
C1
4700pF
C2
4700pF
D1 STPS1H100A
Alternate Nucleo Supply
7V - 12V
CN6
6
7
4
5
1
2
3
8
IOREF
NRST
3V3
5V
VIN
SSQ-108-04-F-S
3v3 5v0
ALTERNATE USE
DEFAULT
DIAG
DIAG
DEFAULT
ALTERNATE USE
IN1
IN1
CN8
1
2
3
4
5
6
PA0
PA1
PA4
PB0
PC1
PC0
SSQ-106-04-F-S
R134 100 (N.M.)
R133 100 (N.M.)
R132 100 (N.M.)
R104 100
R131 100 (N.M.)
R130 100 (N.M.)
Nch-DRV
DIAG
IN1
OUT_FB
OUT_FB
Nch-DRV
ALTERNATE USE
ALTERNATE USE
ALTERNATE USE
DEFAULT
ALTERNATE USE
ALTERNATE USE
ALTERNATE USE
ALTERNATE USE
ALTERNATE USE
DEFAULT
ALTERNATE USE
ALTERNATE USE
IN1
OUT_FB
OUT_FB
Nch-DRV
Nch-DRV
DIAG
Arduino Connectors
R112 100 (N.M.)
R103 100
R101 100
R111 100 (N.M.)
PA5
PA6
PA7
PB6
PC7
PA9
SSQ-110-04-F-S
PB8 10
PB9
AVDD
9
8
7
6
5
4
3
2
1
CN5
R121 100 (N.M.)
R122 100 (N.M.)
R123 100 (N.M.)
R102 100
R124 100 (N.M.)
R125 100 (N.M.)
CN9
PA8
PB10
PB4
PB5
PB3
PA10
PA2
PA3
8
7
6
5
4
3
2
1
SSQ-108-04-F-S
VIN
TP9
5001
IN1
DIAG
OUT_FB
Nch-DRV
(7V-12V NUCLEO supply voltage)
U3
ESDA15P60-1U1M (N.M.)
D2 BAT48 (N.M.)
J3 default open
IN1
DIAG
OUT_FB
Nch-DRV
CN1
1
2
3
Con3
VCC
GND
OUT1
1
2
CN2
Con2
VCC
IN1
R5
390
DIAG
R32.2K
3v3 default: close 1-2
SW2
1
5v0
3
2 con3-strip-male
R42.2K
OUT_FB
Nch-DRV
R6390
Figure 6. X-NUCLEO-OUT10A1 circuit schematic (2 of 2)
VCC
J4 default: closed
J5 default: closed
R15
68k
ISO1
ACPL-217-50AE
R1
27K
R12
22k
R8
1.5k
C4
100nF
TP6
5001
J14 con8-2x4-strip-male default: closed
J9 default:
3-4 = CLOSE
1-2, 5-6, 7-8 = OPEN
3
4
5
1
2
6
U1
Vcc1
IN
DIAG
CoD
NC1
NC2
IPS161HF
ISO2
ACPL-217-50AE
R96.8k
A
D5
RED
D8
C
TDZ6V2J,115
R11
1k
C5
10nF
C6
47nF
C7
0.1uF
R161k
ISO3
ACPL-217-50AE
1
SW1
2
3 con3-strip-male default:
CLOSE 2-3
C
D6
A
150060VS75000
Vcc2
OUT4
OUT3
OUT2
OUT1
GND
R727K
12
11
10
9
8
7
TP3
5001
TP7
5001
J7 default closed
(open load detection = active)
J13 con8-2x4-strip-male
OUT1 default:
3-4 = CLOSE
D7
STPS1H100A
OUT1
1-2, 5-6, 7-8 = OPEN
R10
6.8k
R14
2.2K
default: open
J8 TR3
SM15T10AY
D3
BAT41ZFILM
R227K
ISO4
ACPL-217-50AE
Q1
STN2NF10
1
R13
22k
3
UM2716
Bill of materials
Bill of materials
Table 2. X-NUCLEO-OUT10A1 bill of materials
Item Q.ty
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
0
1
1
1
1
1
0
1
0
1
2
0
1
2
0
1
C1 , C2
C3
C4
C5
C6
C7
C8
Ref.
CN1
CN2
CN5
4700 pF 1825 (4564 Metric) 3000
V (3kV) ±10%
Value
2.2 µF SMD 1206 (3216 Metric)
100 V
100 nF SMD 0805 (2012 Metric)
100 V
10 nF 10000 PF X7R 0603 (1608
Metric) 50 V ±10%
47 nF X7R 0603 (1608 Metric) 50
V ±10%
Ceramic capacitor
Ceramic capacitor
Ceramic capacitor
Ceramic capacitor
0.1 µF X7R 0603 (1608 Metric) 50
V ±10%
Ceramic capacitor
47 µF radial, Can 100 V ±20%
Ceramic capacitor
(not mounted)
AVX
Wurth Electronics
Inc.
Wurth Electronics
Inc.
Wurth Electronics
Inc.
Wurth Electronics
Inc.
Wurth Electronics
Inc.
Con3 10.5X7.4 pitch 3.5 mm
Con2 7.4X7 pitch 3.5 mm
SSQ-110-04-F-S
CN6, CN9 SSQ-108-04-F-S
CN7,
CN10
CN8
SSQ-119-04-L-D
SSQ-106-04-F-S
Description
Ceramic capacitors (not mounted)
Terminal block
Terminal block (not mounted)
Connector
Connectors
Wurth Electronics
Inc.
Wurth Electronics
Inc.
Samtec Inc.
Samtec Inc.
Connectors
Manufacturer
Vishay Vitramon
Samtec Inc.
Samtec Inc.
Order code
HV1825Y472KXHATHV
12061C225KAT2A
885012207128
885382206002
885012206093
885012206095
860040875002
691214110003
691214110002
SSQ-110-04-F-S
SSQ-108-04-F-S
SSQ-119-04-L-D
SSQ-106-04-F-S
D1, D7
D2
D3
DO-214AC, SMA 1 A 100 V
SOD-323F, SC-90
SOD-123 1 V @ 200 mA (DC)
Connector
Power Schottky rectifier
Axial general purpose ginal
Schottky diode
(not mounted)
Surface mount general purpose ginal Schottky diode
ST
ST
ST
STPS1H100A
BAT48JFILM
BAT41ZFILM
17
18
19
1
1
1
D5
D6
SMD 0603 (1608 Metric) 20 mA
SMD 0603 (1608 Metric) 20 mA
Red LED
Green LED
Zener diode
Wurth Electronics
Inc.
Wurth Electronics
Inc.
Nexperia USA
Inc.
150060RS75000
150060VS75000
TDZ6V2J,115
20
21
4
8
D8
SMD, SOD-323F, SC-90 6.2 V
500 mA 500 mW
ISO1,
ISO2,
ISO3,
ISO4
J1, J2, J4,
J5, J7, J8,
J9
3KV, ACPL-217-50AE 4-SOIC
(0.173", 4.40 mm width) con2-strip-male
Optocouplers
Jumpers
Broadcom Limited ACPL-217-50AE
Any Any
UM2716 - Rev 1 page 9/16
UM2716 - Rev 1
UM2716
Bill of materials
Item Q.ty
21a
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
0
2
1
2
2
2
1
1
2
1
2
1
1
1
4
0
2
5
J3
J13, J14
Q1
R1, R2
R3, R4
R5, R6
R7
R8
R9, R10
R11
Ref.
R12, R13
R14
R15
R16
Value Description Manufacturer con2-strip-male con8-2x4-strip-male pitch 2.54
mm
Jumpers (not mounted)
Connector headers
TO-261-4, TO-261AA 100 V 3.3 W
(Tc)
StripFET power
MOSFET in
SOT-223 package
Any
Wurth Electronics
Inc.
ST
SMD 27 K Ohm 0603 (1608
Metric), 0.1 W, 1/10 W ±1%
SMD 2.2 K Ohm 0603 (1608
Metric), 0.1 W, 1/10 W ±1%
SMD 390 Ohm 0603 (1608
Metric), 0.1 W, 1/10 W ±1%
SMD 27 K Ohm 0603 (1608
Metric), 0.1 W, 1/10 W ±1%
SMD 1.5 K Ohm 0603 (1608
Metric), 0.1 W, 1/10 W ±1%
SMD 6.8 K Ohm 0603 (1608
Metric), 0.1 W, 1/10 W ±1%
SMD, 1 K Ohm 0603 (1608
Metric), 0.1 W, 1/10 W ±1%
SMD, 22 K Ohm 0603 (1608
Metric), 0.1 W, 1/10 W ±1%
SMD, 2.2 K Ohm 0603 (1608
Metric), 0.1 W, 1/10 W ±1%
SMD, 68 K Ohm 0603 (1608
Metric), 0.1 W, 1/10 W ±1%
SMD, 1 K Ohm 0603 (1608
Metric), 0.1 W, 1/10 W ±1%
Resistors
Resistors
Resistors
Resistor
Resistor
Resistors
Resistor
Resistors
Resistor
Resistor
Resistor
Yageo
Yageo
Yageo
Yageo
Yageo
Yageo
Yageo
Yageo
Yageo
Yageo
Yageo
R101,
R102,
R103,
R104
R111,
R112,
R121,
R122,
R123,
R124,
R125,
R130,
R131,
R132,
R133,
R134
SW1,
SW2
TP3, TP6,
TP7, TP8,
TP9
SMD, 100 Ohm 0603 (1608
Metric), 0.1 W, 1/10 W ±1%
100 Ohm, SMD, 0603 (1608
Metric), 0.1 W, 1/10 W ±1% con3-strip-male
5001 0.100" Dia x 0.180" L (2.54
mm x 4.57 mm)
Resistors
Resistors (not mounted)
Connection headers
Test points
Yageo
Yageo
Wurth
Keystone
Electronics
39
40
1
1
TR3
U1
DO-214AB, SMC 1500W (1.5 kW)
PowerSSO12 Exposed Pad
Automotive 1500
W TVS in SMC
IC power switch
ST
ST
Any
Order code
61300821121
STN2NF10
RC0603FR-0727KL
RC0603FR-072K2L
RC0603FR-07390RL
RC0603FR-0727KL
RC0603FR-071K5L
RC0603FR-076K8L
RC0603FR-071KL
RC0603FR-0722KL
RC0603FR-072K2L
RC0603FR-0768KL
RC0603FR-071KL
RC0603FR-07100RP
RC0603FR-07100RP
61300311121
5001
SM15T10AY
IPS161HF page 10/16
UM2716
Bill of materials
Item Q.ty
41 1 U2
Ref.
Value
DO-214AB, SMC 1500 W (1.5
kW)
42 0 U3 2-UDFN
Description
1500 W, TVS in
SMC
High-power transient voltage suppressor (not mounted)
Manufacturer
ST
ST
Order code
SM15T39CA
ESDA15P60-1U1M
UM2716 - Rev 1 page 11/16
Revision history
Date
12-Jun-2020
Table 3. Document revision history
Revision
1 Initial release.
Changes
UM2716
UM2716 - Rev 1 page 12/16
UM2716
Contents
Contents
UM2716 - Rev 1 page 13/16
UM2716
List of tables
List of tables
UM2716 - Rev 1 page 14/16
UM2716
List of figures
List of figures
UM2716 - Rev 1 page 15/16
UM2716
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of
Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. For additional information about ST trademarks, please refer to www.st.com/trademarks . All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2020 STMicroelectronics – All rights reserved
UM2716 - Rev 1 page 16/16
Descargar
Enlace público actualizado
Se ha actualizado el enlace público a tu chat. Puedes ver y gestionar tus enlaces de chat después del registro aquí.
Enlace público del documento
Anuncio