TomTom GO 7000 car navigation system User guide

PDF

Dokumentas

Reklama

TomTom GO

1. What’s in the box

What’s in the box a

Your TomTom GO

E b

EasyPort mount

Microphone

Charging light

On/Off button

Light sensor

Reset button

Speaker

Memory card slot (SD card not included) for optional additional maps

USB connector

TomTom connector / RDS-TMC connector

External antenna connector

Audio out connector c

Car charger d

Carry case f

Adhesive disk for

EasyPort Mount e

Documentation pack g

USB cable

2. Before you start

Switching on and off

Install your TomTom GO navigation device in your car following the instructions in the installation section at the start of this book.

To switch on your navigation device, press and hold the On/Off button until you see the start-up screen. The first time you switch on your device, it may take a short time to start.

To set up your device you need to answer a few questions by tapping the screen.

Device not starting

In rare cases, your TomTom GO navigation device may not start correctly or may stop responding to your taps.

First, check that the battery is properly charged. To charge the battery, connect your device to the car charger. It can take up to 2 hours to fully charge the battery.

If this does not solve the problem, you can reset the device. First turn your device off and wait for at least 10 seconds. Then use a straightened paper clip, or something similar, to push the reset button. The reset button is on the bottom of your device.

Battery notes

The battery in your TomTom GO navigation device charges when you connect it to the car charger or to your computer.

When you connect your device to a computer, you are asked if you want to connect to the computer. If you select No and then do not tap the screen within three minutes, the device will automatically switch off. This happens so that the battery can charge faster.

Important: The USB cable should be plugged directly into a USB port on your computer and not into a USB hub or a USB port on a keyboard or monitor.

GPS reception

When you first start your TomTom GO navigation device, the device may need a few minutes to determine your GPS position and show your current position on the map. In the future, your position will be found much faster, usually within a few seconds.

To ensure reception of a strong GPS signal, you should use your device outdoors. Large objects such as tall buildings can sometimes interfere with reception.

When your navigation device is used in combination with a LINK 300 the GPS receiver in the LINK 300 is used by default.

Take care of your device

Never leave your TomTom GO navigation device or accessories in view when you leave the car as they may become an easy target for thieves.

You can set a password for your device which must be entered every time you start it.

It is important to take care of your device.

• Your device is not designed for use in extreme temperatures and any such exposure may cause permanent damage.

• Do not open the casing of your device under any circumstances. Doing so may be dangerous and will void the warranty.

• Wipe or dry the screen of your device using a soft cloth. Do not use any liquid cleaners.

3. Safety

Positioning the dock

Consider carefully where to attach the dock in your car. The dock should not block or interfere in any way with the following:

• Your view of the road

• Any of the controls in your car

• Any of your mirrors

• The airbag

You should be able to reach your navigation device easily when it is in the dock without leaning or stretching. The diagrams show where you can safely attach the dock.

You can attach the dock to the windshield, side window or use a Dashboard

Mount Disk to attach the dock to your dashboard. TomTom also offers alternative mounting solutions for your TomTom navigation device. For more information about Dashboard Mount Disks and alternative mounting solutions, go to www.tomtom.com/accessories.

Installing the Windshield Mount

Make sure that both the Windshield Mount and your window are clean and dry.

1. Press the suction cup firmly against the window on an area where the glass is flat.

2. Twist the rubber grip near the base of the Windshield Mount in a clockwise direction until you hear a click.

The Windshield Mount is now installed.

Safety preferences

We recommend using the safety preferences to make your driving as safe as possible. The safety preferences include, for example, the following options:

• Hide most menu options when driving

• Show safety reminders

• Warn when driving faster than allowed

You can also drive more safely by using voice commands to control your

TomTom GO.

Driving View

4. Driving View

When your TomTom GO starts, you are shown the Driving View along with detailed information about your current location.

Tap the center of the screen at any time to open the Main Menu.

Note: The Driving View is shown in black and white until your GO locates your current position.

New order or message - tap this button to read the new order or message.

Quick menu - switch this on and off in the Preferences menu.

When your navigation device and the TomTom LINK 300 are connected, the quick menu contains the buttons Active order and Change logbook/Report

work time.

Your current position.

The name of the next major road or road sign information, if applicable.

Traffic sidebar.

TomTom WORK status - here are some of the status icons:

Status of order - the status of the current order when you are on a business trip or in work time. Each status has a different icon.

Break - indicates that you selected that you are taking a break. This icon is only shown if Report work time is active.

End of work - indicates that you have finished work.

Private trip - indicates that you selected that you are on a private trip. This icon is only shown when Change logbook mode is active.

Locating disabled - if locating is disabled, the position of your vehicle is not tracked by TomTom WEBFLEET. Locating can be disabled

when you are on private trips, taking a break or have finished work. When locating is disabled, the status icon is shown but is grayed out.

Navigation instruction for the road ahead.

Tap this area to repeat the last spoken instruction and to change the volume.

The name of the street you are on.

Information about your trip such as trip time, remaining distance and arrival time.

To change the information shown, tap Status bar preferences in the

Preferences menu.

Connection indicator - shows that your navigation device has a connection to TomTom LINK 300 and TomTom WEBFLEET. When the connection is lost the outline of the indicator is shown.

GPS signal strength.

5. Advanced Lane Guidance

Your TomTom GO helps you prepare for highway exits and intersections by showing you which lane you should be in.

Note: This information is not available for all intersections or in all countries.

For some exits and junctions, an image shows the turn and the lane you should take.

To turn the images off, tap Hide lane images in the Preferences menu.

For other exits and intersections, your GO shows the lane you should take in the Status bar. To turn this guidance off, tap Change preferences in the Main

Menu, then tap Status bar preferences. Clear the checkbox for Show lane

guidance.

6. Connecting to LINK 300 and WEBFLEET

Connect your TomTom GO device to your TomTom LINK 300 to fully enjoy the benefits of Connected Navigation.

When you first switch on your GO device, you are asked to connect it with the

LINK 300 installed in your vehicle. You can do this immediately or at any time later.

1. Make sure that the LINK 300 is connected to power and has a GPRS connection (see TomTom LINK 300 Installation Guide).

2. Switch on your GO device.

3. Tap the screen to bring up the Main Menu.

4. Tap TomTom WORK.

You are asked to start the activation process. After you have started the activation process your GO device starts searching for Bluetooth devices.

If your GO device finds more than one Bluetooth device, it shows a list of the available devices. Continue with step 5.

If your GO device finds only one LINK 300, continue with step 6.

5. Select your TomTom LINK 300 from the list.

The name starts with LINK followed by the serial number of your LINK 300 or the license plate number of your vehicle. You can find the serial number on the outside of your LINK 300.

6. Enter the Activation Code, which you find in your WEBFLEET contract confirmation.

7. Enter the license plate number of the vehicle.

8. Select the appropriate vehicle type.

If you select Truck or Bus, you have to enter your vehicle dimensions.

If you have properly connected the two devices, you will receive a welcome message from WEBFLEET confirming the activation. In the future the connection will be established automatically.

You can always check the connection status between the two devices by tapping Connection status under TomTom LINK preferences on your navigation device (see Connection status on page 31).

7. Making your first journey

Planning a route with your TomTom GO navigation device is easy. To plan a route, follow the steps below.

Important

: For safety reasons, you should always plan a route before you start your journey.

1. Tap the screen to bring up the Main Menu.

Note: The buttons on your navigation device are shown in full color unless a button is currently unavailable. For example, the button named Find

alternative in the Main Menu is not available until you have planned a route.

2. Tap Navigate to...

3. Tap Address.

When you enter an address, you can choose from the following options:

• City center - tap this button to set your destination as the center of a city or town.

• Street and house number - tap this button to set an exact address as your destination.

• Zip code - tap this button to enter a zip code as your destination.

• Cross street or intersection - tap this button to set your destination as the point where two streets meet.

• Spoken address - tap this button to set your destination by saying the address to your navigation device.

In this example, we will enter an exact address.

4. Tap Street and house number.

Note: When planning a trip for the first time your navigation device asks you to choose a state or country. Your choice is saved and used for all routes you plan.

You can change this setting at any time by tapping the flag.

5. Start to type the name of the town where you want to go.

As you type, the names of the towns that match what you have typed are shown. When your destination appears in the list, tap the name of the town to set the destination.

Tip

: Instead of typing the name, tap this button to say the address by speaking to your navigation device.

6. Start to type the street name and tap on the street when it appears in the list.

As with the name of the town, the names of the streets that match what you have typed are shown. When your destination appears in the list, tap the name of the street to set the destination.

7. Enter the house number and then tap Done.

8. Your navigation device asks if you need to arrive at a particular time. For this exercise, tap NO.

The route is calculated by your device using IQ Routes

IQ Routes is used to plan the best possible route taking into account the real average speeds measured on the roads.

9. When the route has been calculated, tap Done.

Your TomTom GO navigation device will warn you about any traffic delays and immediately begin to guide you to your destination, using both spoken instructions and on-screen directions.

Arrival times

When you plan a route, your TomTom GO asks you if you need to arrive at a particular time.

Tap YES to enter a preferred arrival time.

Your GO calculates your arrival time and shows you whether you will arrive on time.

You can also use this information to work out when you need to leave. If your

GO shows that you will arrive 30 minutes early, you can wait and leave in 30 minutes time, rather than arrive early.

Your arrival time is constantly recalculated during your trip. The status bar shows whether you will arrive on time or if you are going to be late, as shown below:

You will arrive 55 minutes before the arrival time you entered.

If the estimated arrival time is more than five minutes before the time you entered, it is shown in green.

You will arrive 3 minutes before the arrival time you entered.

If the estimated arrival time is less than 5 minutes before the time you entered, it is shown in yellow.

You will arrive 19 minutes late.

If the estimated arrival time is later than the time you entered, it is shown in red.

Status bar preferences

Tap Status bar preferences in the Preferences menu, to enable or disable arrival time notifications.

Select the required options on the first menu screen and then tap Done.

To enable arrival time notifications, select Show leeway to arrival time.

Other navigation options

When you tap Navigate to..., you can set your destination in many ways, not just by entering the address. The other options are listed below:

Tap this button to navigate to your Home location.

You will probably use this button more than any other.

Home

Tap this button to select a Favorite as your destination.

Favorite

Tap this button to enter an address as your destination.

Address

Tap this button to select your destination from a list of places you have recently used as destinations.

Recent destination

Tap this button to navigate to a Point of Interest (POI).

Point of

Interest

Tap this button to select a point on the map as your destination using the map browser.

Point on map

Tap this button to enter a destination using latitude and longitude values.

Latitude

Longitude

Tap this button to select your last recorded position, as your destination.

Position of last stop

Planning a route in advance

You can use your GO to plan a route in advance, selecting your starting point and your destination.

Here are some more reasons to plan a route in advance:

• Find out how long a trip is going to take before you start.

You can also compare trip times for the same route at different times of the day or on different days of the week. Your TomTom GO uses IQ Routes

when planning a route. IQ Routes calculates routes based on the real average speeds measured on roads.

• Study the route of a trip you are planning.

• Check a route for someone who is coming to visit you and then explain the route to them in detail.

To plan a route in advance, follow these steps:

1. Tap the screen to bring up the main menu.

2. Tap the arrow button to move to the next menu screen and tap Prepare

route.

Prepare route

3. Select the starting point for your trip in the same way that you would select your destination.

4. Set the destination for your trip.

5. Choose the type of route that should be planned.

• Fastest route - the route which takes the least time.

• Shortest route - the shortest distance between the locations you set. This may not be the quickest route, especially if the shortest route is through a town or city.

• Avoid freeways - a route which avoids freeways.

• Walking route - a route designed for making the trip on foot.

• Bicycle route - a route designed for making the trip on a bicycle.

• Limited speed - a route for a vehicle which can only be driven at a limited speed. You have to specify the maximum speed.

6. Choose when you will make the trip you are planning. There are three options:

• Now

• Specific date and time - you will be asked to enter the date and time.

• No specific date and time

If you select either Now or Specific date and time, your GO uses IQ Routes to work out the best possible route at that time, using the real average speeds measured on roads. In this way you can compare how long a trip takes at different times of day, or on different days of the week.

7. Your TomTom GO plans the route between the two locations you selected.

More information about a route

You can access these options for the route you last planned by tapping the

Details button on the route summary screen.

You can then select from the following options:

Tap this button for a list of all the turn instructions on the route.

This is very useful if you need to explain a route to someone else.

Browse as text

Browse as images

Tap this button to see each turn in the trip. Tap the right and left arrows to move forwards and backwards through the trip.

Tap the screen to turn off the 3D display and view the map from above.

Tap this button to see an overview of the route using the map browser.

Browse map of route

Tap this button to watch a demo of the trip. You can interrupt the demo at any time by tapping the screen.

Show route demo

Tap this button to open the route summary screen.

Show route summary

Tap this button to see your route.

View route

8. TomTom WORK menu

To open the TomTom WORK menu, tap the screen to bring up the Main Menu, then tap TomTom WORK.

• Active order - tap this button to access and work on the active order.

• Show orders - tap this button to view the list of orders and messages.

• Report to office - tap this button to send text or status messages to the office.

• Report work time - tap this button to report when you start and finish work, and start and finish breaks (only available if activated).

• Change logbook mode - tap this button to switch between private and business trips (only available if activated).

• Change driver - tap this button to change the driver.

9. Orders and messages

The office can send service, delivery and pick up orders. They are stored on your TomTom navigation device.

You can read and deal with them at any time by tapping Show orders in the

TomTom WORK menu, or by tapping Active order in the Quick menu.

These symbols show the type and status of items in your list of orders and messages:

New text message

Text message that has been read

New service order

Service order in progress

Suspended service order

Finished service order

Canceled or rejected service order

New delivery or pick up orders

Working on orders

Tap the button for new orders and messages in the Driving View to bring up the latest unread order or message.

To bring up the complete list of your orders and messages do the following:

1. Tap the screen to bring up the Main Menu.

2. Tap TomTom WORK.

3. Tap Show orders.

4. Select an order from the list.

5. To work on this order tap I agree. To reject the order tap Options, then tap

Reject order. You can enter a reason for rejection.

If you have agreed, you are asked to start this order. If the order contains destination data, you are asked to start navigation.

As soon as you start the order, you can report your current activity.

Tap the button that shows the activity you want to report.

Tap Status to report to your office using the status messages defined by the office.

To open the order you are currently working on tap the quick menu button in the Driving View, then tap Active order.

Suspend and change orders

1. To suspend the current order, select it from the list of orders and messages.

2. Tap Options.

3. Tap Suspend.

Switch to another order

1. To switch to another order, select the order from the list of orders and messages.

2. You are asked to suspend the current order and to start working on the new one.

You can continue working on the suspended order at any time. To do this, select the suspended order from the list and tap Resume.

Cancel orders

1. If you want to cancel an order, first select the order from the list of orders and messages.

2. Tap Options.

3. Tap Cancel.

You have to enter a reason for canceling the order.

Call contact

10. Call contact

Orders can contain a contact name and a telephone number. You can call this number from your TomTom navigation device.

Note: To use the Call contact feature you need a Bluetooth® mobile phone that is compatible with your TomTom GO.

1. Tap the screen to bring up the Main Menu.

2. Tap TomTom WORK.

3. Tap Show orders.

4. Select an order from the list by tapping it.

5. Tap Options.

6. Tap Call.

7. Tap the contact to dial the number.

11. Report to office

Send text message

To send a text message to the office, do the following.

1. Tap Report to office in the TomTom WORK menu.

2. Tap Send text message.

3. Enter your text (see below).

4. To send your complete message to the office, tap Done.

Enter your message using the keyboard and the following buttons:

Tap this button to enter capital letters.

Tap this button to enter lowercase letters

Tap this button to switch to the numeric/special characters keyboard

Tap this button to switch back to alphabetic keyboard

Tap this button to delete single characters

Send predefined message

Predefined messages must be defined by the office. You can also add information to a predefined message.

1. Tap Report to office in the TomTom WORK menu.

2. Tap Send predefined message.

3. Select a predefined message from the list by tapping it.

Tap Send to send the message directly to the office.

If you want to add information, tap Edit then send your message.

12. Driver identification

To generate personalized work time reports, you need to enter your PIN code.

Note: Using TomTom WEBFLEET, the office can select that you have to enter your PIN code each time you switch on your TomTom navigation device.

1. Tap the screen to bring up the Main Menu.

2. Tap TomTom WORK.

3. Tap Change Driver.

4. Select your name from the driver list by tapping it.

5. Enter your four digit PIN code (provided by your WEBFLEET administrator), then tap Done.

Your PIN code is now stored and used for all reports until you change it.

13. Report work time

You can report the time you start and finish work, as well as the time you spend having breaks.

To do this, you must first set your driver name (see Driver identification on page 24).

Report work time

To report work times to TomTom WEBFLEET, do the following:

1. Tap the quick menu button in the Driving View.

2. Tap Report work time.

3. Tap the appropriate button to change your work status.

When you tap Finish work, this is indicated in the driving view (see Vista de

conducción on page 46).

If you are working on an order, the current order status is shown in the Driving

View.

Note: Either Report work time or Change logbook mode is available. These are activated using TomTom WEBFLEET by the office.

Turning on/off the navigation device

When you turn on your TomTom navigation device, you may be asked to report either Start work or Finish break. This happens if the last status you reported before switching off was Finish work or Start break.

When you turn off your TomTom navigation device and you have not reported

Finish work or Start break, your device displays a menu with the options

Finish work, Start break, Active order and Power off. You can then report your status to TomTom WEBFLEET before turning off.

Note: The function of prompting Report work time transactions is activated using TomTom WEBFLEET by the office.

14. Change logbook mode

You can generate a driver’s logbook with your TomTom navigation device. To use this functionality you need to adjust the odometer first. You can do this by tapping Adjust in the logbook. See Adjust odometer on page 29.

To change the logbook mode (kind of trip), do the following:

1. Tap the quick menu button in the Driving View.

2. Tap Change logbook mode.

Note: Either Report work time or Change logbook mode is available. These are activated using TomTom WEBFLEET by the office.

3. Select the appropriate logbook mode (type of trip).

The current logbook mode is shown in the bottom half of the screen, as well as journey specific information.

If the logbook mode is set to Private trip, this is shown in the Driving View.

During a business trip, the current order status is shown.

15. TomTom LINK preferences

In the TomTom WORK menu you can find the TomTom LINK preferences menu. Use the preferences menu to do the following:

• Synchronize the odometer of your TomTom navigation device with your vehicle’s odometer (see Adjust odometer on page 29).

• View the connection status between your TomTom navigation device, your

TomTom LINK 300 and TomTom WEBFLEET (see Connection status on page 31).

• Choose to use the GPS signal either from your TomTom navigation device or from your TomTom LINK 300.

Important

: Make sure the GPS source you select has a clear view of the sky which it needs for good GPS reception.

• Change the vehicle in which you are using your TomTom GO.

Note: Use with care. When you change the vehicle you delete all orders and messages, text and status messages, reporting information such as work time or logbook trips, etc. from your TomTom navigation device.

16. Adjust odometer

When you use the logbook you need to synchronize the odometer on your

TomTom navigation device with your vehicle’s odometer.

1. Tap the screen to bring up the Main Menu.

2. Tap TomTom WORK.

3. Tap TomTom LINK preferences.

4. Tap Set odometer.

5. Tap the buttons to adjust the odometer to match your vehicle’s odometer.

6. Tap Done to save the changes.

17. Change vehicle

When you change the vehicle you need to connect your TomTom GO navigation device to the TomTom LINK 300 installed in the new vehicle.

Important

: The list of orders and messages, all reporting information, and all messages are deleted when you change vehicle.

1. Tap the screen to bring up the Main Menu.

2. Tap TomTom WORK.

3. Tap TomTom LINK preferences.

4. Tap Change vehicle.

5. Select the new LINK 300 you want to connect your GO device to from the list of Bluetooth devices.

Enter the vehicle’s license plate number and choose the applicable vehicle type (see Connecting to LINK 300 and WEBFLEET on page 13).

18. Connection status

To see the connection status of your TomTom GO navigation device, your

TomTom LINK 300 and TomTom WEBFLEET do the following:

1. Tap the screen to bring up the Main Menu.

2. Tap TomTom WORK.

3. Tap TomTom LINK preferences.

4. Tap Connection status.

Here you have a brief overview of the connection status:

• GSM connection

• GPRS connection

• Connection to TomTom WEBFLEET

• If Bluetooth is disabled and how to enable it.

• If the LINK 300 is disconnected and how to initiate the reconnection.

• If the LINK 300 has not been activated and how to activate it

Note: To activate you need the activation code given on the contract confirmation letter.

19. Considerations

This section contains important considerations for the use of the TomTom GO navigation device and the TomTom LINK 300.

Maintain connection

When you are using the TomTom WORK features, the TomTom GO device and the TomTom LINK 300 must be connected.

Messages you send to the office are only sent once your TomTom GO and the

TomTom LINK 300 are connected. While there is no connection between the two devices, the messages are stored on your TomTom GO navigation device.

This means, for example, that if you change the logbook mode from Private

trip to Business trip while the two devices are disconnected, the logbook records the time you change the trip as the time when you connect the devices.

Configuration from the office

Status message configuration and the selection between Change logbook

mode and Report work time can only be made by the office.

20. Finding alternative routes

Once you have planned a route, you may want to change something about the route, without changing your destination.

Why change the route?

Maybe for one of these reasons:

• You can see a roadblock or a line of traffic ahead.

• You want to travel via a particular location, to pick someone up, stop for lunch or fill up with gas.

• You want to avoid a difficult intersection or a road you don’t like.

Find alternative...

Tap Find alternative... in the Main Menu to change the route that is currently planned.

The Find alternative... button is also shown in the route summary screen after you plan a route.

Calculate alternative

Avoid roadblock

Tap this button to calculate an alternative to the route already planned.

Your GO will look for another route from your current location to your destination.

If you decide you would prefer to use the original route after all, tap

Recalculate original.

Why would I need to do this?

Apart from the roads near your position and near your destination, the new route will use totally different roads to reach your destination. This is an easy way of calculating a totally different route.

Tap this button if you can see a roadblock or a line of traffic ahead. You then have to choose how much of the route ahead you want to avoid.

Choose from the different options: 100yd, 1/4 Mile, 1 Mile and 3 Miles. Your

GO will recalculate your route avoiding the section of the route for the distance you selected.

Don’t forget that once a new route is calculated, you may have to turn off the road you are on very soon.

If the roadblock suddenly clears, tap Recalculate original to return to your original route.

Travel via...

Tap this button to change your route so that it passes a particular location, perhaps to pick someone up on the way. When you do this, a marker is shown on the map for the location you choose the travel over.

You choose the location you want to pass in the same way as you choose a destination. So you can select from all the same options: for example,

Address, Favorite, Point of Interest and Point on map.

Your GO will calculate a new route to your destination that passes the location you chose. Unlike your final destination, your GO does not inform you when you pass by this location.

Using this button, you can only travel via one location. If you want to pass more than one, use an Itinerary.

Tap this button to return to the original route without deviations to avoid roadblocks or traveling via particular locations.

Recalculate original

Avoid part of route

Minimize delays

Tap this button to avoid a part of the route. Use this button if you see that your route includes a road or junction you don’t like, or which is wellknown for traffic problems.

You then choose the road you want to avoid from a list of the roads on your route.

Tap this button to recalculate your route so that it avoids traffic problems as much as possible. Your GO will check if there are any traffic problems on your route and work out the best route to avoid the problems.

Note: This button is only available with TomTom Traffic enabled.

21. Favorites

What are Favorites?

Favorites are places that you often visit. You can create Favorites so that you don’t have to enter the address every time you want to navigate there.

They don’t have to be places you especially like, just useful addresses.

How can I create a Favorite?

From the Main Menu, tap Add Favorite.

You can then select the location of the Favorite from the list below.

Give your Favorite a name that is easy to remember. Your GO will always suggest a name, usually the address of the Favorite. To enter the name, just start typing. You don’t have to delete the suggested name.

You can set your Home location as a Favorite.

Home

Favorite

Address

You cannot create a Favorite from another Favorite. This option will always be unavailable in this menu.

To rename a Favorite, tap Manage Favorites in the Preferences menu.

You can specify an address to be a Favorite. When you enter an address, you can choose from four options.

• City center

• Street and house number

• Zip code

• Crossing or intersection

Select a Favorite location from a list of places you have recently used as destinations.

Recent destination

Point of

Interest

My location

You can add a Point of Interest (POI) as a Favorite.

Does it make sense to do this?

If you visit a POI you particularly like, for example a restaurant, you can add it as a Favorite.

To add a POI as a Favorite, tap this button, then do the following:

1. Narrow your choice of POIs by selecting the area where the POI is.

You can select one of these options:

• POI near you - to search from a list of POIs near your current position.

• POI in city - to choose a POI in a particular town or city. You have to specify a town or city.

• POI near Home - to search from a list of POIs near your Home location.

If you are currently navigating to a destination, you can also select from a list of POIs which are on your route or near your destination. Choose one of these options:

• POI along route

• POI near destination

2. Select the category of POI.

Tap the category of POI if it is shown or tap the arrow to choose from the complete list.

Tap Any POI category to search for a POI by name.

Tap this button to add your current position as a Favorite.

For example, if you stop somewhere interesting, while you are there you can tap this button to create the Favorite.

Tap this button to create a Favorite using the map browser.

Select the location of the Favorite using the cursor, then tap Done.

Point on map

Tap this button to create a Favorite by entering latitude and longitude values.

Latitude

Longitude

Tap this button to select your last recorded position as your destination.

Position of last stop

How can I use a Favorite?

You will normally use a Favorite as a way of navigating to a place without having to enter the address. To navigate to a Favorite, do the following:

1. Tap the screen to bring up the main menu.

2. Tap Navigate to...

3. Tap Favorite.

4. Select a Favorite from the list.

Your GO calculates the route for you.

5. When the route is calculated, tap Done.

Your GO will immediately start guiding you to your destination with spoken instructions and visual instructions on the screen.

How can I change the name of a Favorite?

1. Tap the screen to bring up the main menu.

2. Tap Change preferences to open the Preferences menu.

3. Tap Manage Favorites.

4. Tap the Favorite you want to rename.

5. Tap Rename.

How can I delete a Favorite?

1. Tap the screen to bring up the main menu.

2. Tap Change preferences to open the Preferences menu.

3. Tap Manage Favorites.

4. Tap the Favorite you want to delete.

5. Tap Delete.

Browse map

22. Browse map

To look at the map in the same way as you might look at a traditional paper map, tap Browse map in the Main Menu.

You can move the map by touching the screen and moving your finger across the screen.

Options

The scale bar

GPS button

Tap this button to center the map on your current position.

Options

The cursor

The Find button

Tap this button to find specific addresses.

The Cursor button

Tap this button to navigate to the cursor position, make a Favorite of the cursor position, or find a Point of Interest near the cursor position.

The zoom bar

Zoom in and out by moving the slider.

Tap the Options button to set the information shown on the map. You can choose to show the following information:

• Points of interest. Tap POI below the list of options to select which POIs are shown.

• Favorites

• Traffic

• Images

• Names

• Coordinates

23. LIVE Services

Regional availability

Note: LIVE services are only available in designated countries. For more information on available services in your country, go to

www.tomtomwork.com/liveservices.

TomTom Traffic

Traffic is a unique TomTom LIVE Service for receiving up-to-date traffic information.

In combination with IQ Routes, Traffic helps you plan the best possible route to your destination taking into account the latest traffic information.

A route is calculated taking into account the current local traffic conditions.

Your TomTom GO automatically receives regular traffic information updates.

If traffic incidents are found on your route, you are asked if you want to replan the current route to try and avoid the traffic incidents.

Fuel Prices

The Fuel Prices service sends up-to-date information about fuel prices directly to your device or via TomTom HOME when your GO is connected to your computer.

Search for the best fuel prices

To search for the cheapest fuel prices, do the following. In this example, you will plan a route to the cheapest gas station nearby.

1. Tap the screen to bring up the Main Menu, then tap TomTom Services.

2. Tap Fuel Prices.

3. Select the type of fuel used in your vehicle.

4. Tap Cheapest nearby, then tap the name at the top of the list.

The location is shown on the map.

5. Tap Select.

You are asked if you want to navigate to the gas station.

6. Tap Yes.

You may be asked if you need to arrive at a particular time, if this option is enabled.

The route is planned and a summary of the route is shown on the map.

Update Fuel Prices

To make sure you have access to the latest fuel prices, you should regularly update your TomTom GO by downloading the latest fuel pricing information.

To download the latest fuel prices, tap Update in the Fuel Prices menu and follow the instructions shown on the screen.

The latest updates for fuel pricing information are downloaded directly to your device. If for any reason your GO is unable to make a direct connection, you can update your device when you connect to TomTom HOME.

TomTom local search powered by Google

Using local search, you can search the Google listings to find stores and businesses near you, or any another location, and navigate there.

Using local search

To find a destination using local search and plan a route to that location, follow the steps below. In this example, you will search for a supermarket near your current location.

1. Tap the screen to bring up the Main Menu, then tap Navigate to.

2. Tap the Google button.

3. Tap Search near you.

4. Type ’supermarket’ then tap OK.

The locations that match your search are shown in a list.

5. Tap one of the locations in the list.

The location is shown on the map.

Tap Details to see more information about this location.

6. Tap Select to plan a route to the location.

Your TomTom GO plans a route to the location you selected.

TomTom Weather

TomTom Weather gives you five day weather reports for any location on your map.

24. TomTom Traffic

Traffic is a unique TomTom LIVE Service for receiving up-to-date traffic information.

In combination with IQ Routes, Traffic helps you plan the best possible route to your destination taking into account the latest traffic information.

A route is calculated taking into account the current local traffic conditions.

Your TomTom GO automatically receives regular traffic information updates.

If traffic incidents are found on your route, you are asked if you want to replan the current route to try and avoid the traffic incidents.

Safety Notice

Your TomTom navigation device contains a GSM/GPRS module which can interfere with electrical devices such as cardiac pacemakers, hearing aids and aviation equipment.

Interference with these devices may endanger the health or life of others.

Do not use near unprotected electrical units nor in areas where the use of mobile telephones is prohibited, such as hospitals and airplanes.

Using TomTom Traffic

The Traffic bar is shown on the right side of the Driving View. It warns you about traffic incidents on your planned route.

The top of the Traffic bar represents your destination and shows the total delay time for any incidents on your route.

The central section of the Traffic bar shows individual traffic incidents in the order they occur on your route.

The bottom of the Traffic bar represents your current position and shows the distance to the next incident.

To find the quickest route to your destination taking into account the latest traffic information, do the following:

1.Tap the sidebar.

Tip

: If you have trouble tapping the sidebar and the Main Menu is being displayed instead of the traffic menu, try tapping your finger half on the sidebar and half off the screen.

2. Tap Minimize traffic delays.

Your device looks for the quickest route to your destination.

It is possible that the new route may also include traffic delays, or may even be the same route as before. You can re-plan the route to avoid all delays, but this new route will take longer than the quickest route already shown.

3. Tap Done.

Tip

: You can let your TomTom device automatically minimize traffic delays for you.

Minimize delays

You can set Traffic to minimize traffic delays on your route each time the latest traffic information updates are received.

1. Tap TomTom Traffic in the Main Menu.

2. Tap Change Traffic preferences.

3. Select Automatically minimize delays after every traffic update.

4. Tap Done.

Changing Traffic preferences

Change Traffic preferences

Use the Change Traffic preferences button to choose how Traffic works on your device.

1. Tap TomTom Traffic in the Main Menu.

2. Tap Change Traffic preferences.

3. To hear a beep sound when a new traffic incident occurs on your route, select Beep when traffic situation on route changes and then tap Done.

4. If a faster route is found while you are driving, Traffic can replan your journey to use the faster route. Select one of the following options and then tap Done.

Always switch to that route

Ask me if I want to change

Never change my route

5. Tap Done.

The Traffic sidebar

The Traffic sidebar shows you traffic incidents on your route, displaying the following information:

• A symbol for each traffic incident in the order they occur along your planned route.

• The estimated delay of the next traffic incident on your route.

• The estimated delay for all incidents on your route.

• The distance from your current location to the next incident on the Traffic sidebar.

Note: The color of the sidebar changes depending on how old the traffic information is on your device.

An example of an Traffic sidebar is shown below.

In the example, the sidebar shows you that there are two incidents ahead.

To re-plan your route to avoid these incidents, tap the sidebar to open the

TomTom traffic menu, then tap Minimize traffic delays.

Note: To make the Traffic sidebar more readable some incidents may not be shown. These incidents will always be of minor importance and only cause short delays.

Making commuting to work easier

The Home to work and Work to home buttons in the Traffic menu let you check your route to and from work with one tap of a button. When you use either of these buttons, your device checks the route for possible delays and if it finds any, provides you with the possibility to avoid them.

Change home-work

The first time you use Home to work, you must set your traffic home and work locations, do the following:

1. Tap TomTom Traffic in the Main Menu.

2. Tap Show home-work traffic.

3. Tap Change home-work

4. Set your home location

5. Set your work location.

You can now use the Home to work and Work to home buttons of the Show home-work traffic menu.

Note: The home location you set here is not the same as the home location you can set in the Preferences Menu. In addition, the locations you use here do not have to be your actual home and work locations. If there is another route that you often travel, you can set Work/Home to use these locations instead.

For example, to check for delays on your route home, do the following:

1. Tap TomTom Traffic in the Main Menu.

2. Tap Show home-work traffic.

3. Tap Work to home.

The driving view is shown. If the Traffic sidebar shows any delays on your route, tap the Traffic sidebar and then Minimize traffic delays to see your fastest route to home.

Checking traffic incidents in your area

Get an overview of the traffic situation in your area, using the map. To find local incidents and their details, do the following:

1. Tap TomTom Traffic in the Main Menu.

2. Tap Browse map.

Browse map

The map browser screen is shown.

3. Tap the blue compass image in the top right of the screen.

The map centers itself on you current location and any traffic incidents in the area are shown.

4. Tap on any traffic incident to get more information.

A screen is shown that gives you detailed information about the incident you chose. To display information about surrounding incidents use the left and right arrows at the bottom of this screen.

Traffic sidebar colors

The Traffic sidebar changes colors depending on how old the traffic information is on your device. The sidebar colors are:

Dark blue - The traffic information on your device is up to date.

Lilac - The traffic information on your device has not been updated for at least 10 minutes. Traffic still warns you about traffic incidents, but the information is at least ten minutes old.

Grey - The traffic information on your device has not been updated for at least 15 minutes. Traffic will only warn you about traffic incidents once it has been able to update this information.

Note: The traffic information on your device is updated automatically and the

Traffic sidebar will normally remain dark blue. However, it is possible that the device might not update traffic information. This may happen if, for example, there is no or poor network coverage in your area, or if you are driving in a country other than the one for which you purchased TomTom Traffic.

Traffic incidents

Traffic incidents are displayed as small symbols on the Driving View and the

Traffic sidebar. There are two type of symbols:

• Symbols shown in a red square are incidents that Traffic can help you to avoid.

• Symbols shown in a red triangle are weather related and are for information only. You cannot use Traffic to avoid them.

Traffic incident symbols:

Accident

Road works

One or more lanes closed

Road closed

Traffic incident

Traffic jam

Weather related symbols:

Fog

Rain

Wind

Ice

Snow

Note: The incident avoided symbol is shown for any traffic incident that you avoid using TomTom Traffic.

Traffic menu

To open the Traffic menu, tap the Traffic sidebar in the Driving View or tap

TomTom Traffic in the Main Menu. The following buttons are available:

Tap this button to re-plan your route based on the latest traffic information.

Minimize traffic delays

Show traffic on route

Tap this button to get an overview of any traffic incidents along your route.

Use the left and right buttons of the overview screen to see more detailed information about each incident. You can also use the Replan button of the overview screen to replan your route avoiding the traffic incidents.

Tap this button to calculate and show the quickest route from your home location to your place of work and back.

Show homework traffic

Tap this button to browse the map and see the traffic information displayed on the map.

Browse map

Tap this button to change your preferences for how TomTom Traffic works on your device.

Change

Traffic preferences

25. TomTom Map Share

With TomTom Map Share, you can correct errors on your map and share those corrections with other people in the TomTom Map Share community as well as receive corrections made by others.

If you find a street that has recently been blocked to traffic but was open before, you can use Map Share to correct your map and then share the correction with other Map Share members.

You can use Map Share to send and receive map corrections during the first year after the map’s release date. This means that one year after the release date, you will no longer be able to send or receive map corrections for that version of the map - You will still be able to make corrections to your own map for use on your own device.

You choose the type of corrections you want and each time you connect your

TomTom GO to TomTom HOME, the map will be updated automatically.

Note: TomTom Map Share is not available in all regions. For more information, go to tomtom.com/mapshare

Map corrections

There are two types of map corrections:

• Corrections that are immediately shown on the map. These include, changing the traffic flow of a street, blocking or renaming a street and adding or editing POIs.

This type of change is immediately shown on your own map. You can hide these corrections at any time in the Map Share preferences menu.

• Corrections that are reported to TomTom but not shown immediately on your map. These include, missing streets, errors in freeway entrances and exits and missing rotaries.

This type of correction is investigated by TomTom and once verified, is included in the next map release. These corrections are therefore not shared with the Map Share community.

Tip

: If you cannot see the Map corrections button in the Main Menu, tap Show

ALL menu options in the Preferences menu.

Making a map correction

Correct a map error

Important

: For safety reasons, you should only mark a location when you are driving. Do not enter the full details of an error while you are driving.

1. Tap Map corrections in the Main Menu.

2. Tap Correct a map error.

A list of possible map corrections is shown.

3. Select the type of correction you want to report.

Note: If you tap Add missing POI or Report other error you will be asked for some additional information before the next step.

4. Select the method you want to use for selecting the location of the correction.

5. When you have found the location, tap Done.

6. Enter correction or confirmation of correction now.

Receiving the latest map updates

When you connect your TomTom GO to your computer, TomTom HOME automatically downloads any available map corrections and sends any changes you have made, to the Map Share community.

There are several types of corrections which can be set in the Correction preferences menu.

Marking a map error while on the move

Important

: For safety reasons, you should only mark a location when you are driving. Do not enter the full details of an error while you are driving.

If you notice an item on your map that needs attention, you can mark the location using the Report button and then enter the details when you are no longer driving.

To show the Report button in the Driving View or in the quick menu, do the following:

1. Tap Map corrections in the Main Menu.

Tip

: If you cannot see the Map corrections button in the Main Menu, tap Show

ALL menu options in the Preferences menu.

2. Tap Correction preferences.

3. Tap Done and then tap Done again.

4. Select Show report button, then tap Done.

The Report button is shown on the left-hand side of the Driving View. After you mark a location, you can add more information about the change when you open the Map corrections menu.

For example, you are driving to a friendqs house and you notice that the name of the street you are on is different from the one on your map. To report the change, tap the Report button and your GO will save your current location.

You can then send the correction to TomTom Map Share when you have finished your trip.

TomTom Map Share community

To join the Map Share community, do the following:

1. Tap Map corrections in the Main Menu.

Tip

: If you cannot see the Map corrections button in the Main Menu, tap Show

ALL menu options in the Preferences menu.

2. Tap Download corrections made by others.

3. Tap Join.

When you connect your GO to your computer, TomTom HOME downloads new corrections and sends your corrections to the Map Share community.

Important

: TomTom Map Share corrections are not sent to your navigation device using a wireless connection. You should regularly connect your device to your computer and use TomTom HOME to check for new updates.

Correction preferences

The correction preferences set the way TomTom Map Share works on your device.

You can set the following preferences:

• Use the trust level slider to choose the types of corrections from the Map

Share community you want to use on your maps.

• Decide if you want to share your corrections with others.

• Show or hide the report button in the Driving View.

To set your preferences, select Map corrections in the Main Menu.

Tip

: If you later decide you want to remove corrections from the map, clear the checkbox next to the types of corrections you want to remove. If you clear all the checkboxes, your map returns to the original state before the first correction.

Trust slider

Use the Trust level slider to set the type of map corrections you want added to your map. To do this, tap Correction preferences in the Map corrections menu.

There are four levels of trust that you can choose. The level changes when you move the slider:

• TomTom - only accept changes made by TomTom.

• Trusted sources - accept changes made by TomTom and by trusted users who have been verified by TomTom.

• Many users - accept changes made by TomTom, by trusted users who have been verified by TomTom and changes made by a high number of Map

Share community members.

• Some users - accept changes made by TomTom, by trusted users who have been verified by TomTom and all changes that have been made by

Map Share community members.

Types of map correction

There are several types of correction that you can make to a map.

(Un)block street

To make a correction to your map, tap Map corrections in the Main Menu then tap Correct a map error. The following types of corrections are shown.

Tap this button to block or unblock a street. You can block or unblock the street in one or both directions.

For example, to correct a street near to your current location, do the following:

1. Tap (Un)block street.

2. Tap Near you to select a street near your current location. You can select a street by name, a street near your Home location or a street on the map.

3. Select the street or section of a street you want to correct by tapping it on the map.

The street you select is highlighted and the cursor shows the name of the street.

4. Tap Done.

Your device shows the street and whether the traffic is blocked or allowed in each direction.

Reverse traffic direction

5. Tap one of the direction buttons to block or unblock the flow of traffic in that direction.

6. Tap Done.

The next time you connect your device to TomTom HOME, your corrections are shared with the TomTom Map Share community.

Tap this button to correct the traffic direction of a one-way street, where the direction of traffic is different to the direction shown on your map.

Note: Reverse traffic direction only works for one-way streets. If you select a two-way street you will be given the chance to block/unblock the street rather than changing the direction.

Edit street name

Tap this button to change the name of a street on your map.

For example, to rename a street near to your current location:

1. Tap Edit street name.

2. Tap Near you.

3. Select the street or section of a street you want to correct by tapping it on the map.

The street you select is highlighted and the cursor shows the name of the street.

4. Tap Done.

5. Type the correct street name.

6. Tap Done.

Tap this button to change and report incorrect road turn directions.

Change turn restrictions

Tap this button to change and report road speed limit.

Change road speed

Add missing

POI

Tap this button to add a new Point of Interest (POI).

For example to add a new restaurant near to your current location:

1. Tap Add missing POI.

2. Tap Restaurant in the list of POI categories.

3. Tap Near you.

4. Select the location of the missing restaurant.

You can select the location by entering the address or by selecting the location on the map. Select Near you or Near home to open the map at your current location or at your Home location.

5. Tap Done.

6. Type the name of the restaurant then tap OK.

7. If you know the telephone number of the restaurant you can type it, then tap OK.

If you don’t know the number, just tap OK without typing a number.

Edit POI

Report other error

Tap this button to edit an existing POI.

You can use this button to make the following changes to a POI:

• Delete the POI.

• Rename the POI.

• Change the telephone number of the POI.

• Change the category that a POI belongs to.

• Move the POI on the map.

Tap this button to report other types of corrections.

These corrections are not immediately applied to your map. Your

TomTom GO sends a special report to TomTom Map Share.

You can report missing streets, errors in motorway entrances and exits and missing roundabouts. If the correction you want to report is not covered by any of these report types, enter a general description then tap Other.

26. Sounds and voices

Your TomTom GO plays the following kinds of sounds:

• Spoken instructions

• Hands-free calls

• Warnings

Changing the volume level

You can change the volume in three ways:

• Tap the bottom left hand area of the Driving View. The last spoken instruction is repeated and the volume level is shown.

Move the volume slider to adjust the volume.

• In the Main Menu, tap Change preferences, then tap Volume preferences.

Tap Test to check your changes.

• You can set your GO to change the volume automatically depending on how noisy it is in the car.

Changing the volume automatically

Volume preferences

Your TomTom GO can change the volume automatically.

1. In the Main Menu, tap Change preferences.

2. Tap Volume preferences.

3. Select Link volume to noise level.

4. Tap Done.

Selecting a voice

Voice preferences

To change the voice being used by your TomTom GO, tap Voice

preferences in the Preferences menu, then tap Change voice. Select a voice from the list.

Your TomTom GO has two different kinds of voices:

• Computer voices

These are generated by your GO. They provide spoken instructions while you are driving and can pronounce street names and announce messages, traffic reports, weather reports, tips and tutorials.

• Human voices

These are recorded by an actor.

Note: Human voices only provide spoken instructions.

How do computer voices work?

Your TomTom GO makes use of text-to-speech technology to generate computer voices. A text-to-speech program converts written text, for example an instruction like “Turn right”, into the sound of a human voice.

The text-to-speech program looks at the whole sentence to make sure that the sound you hear is as close to the real thing as possible. The program is also able to recognize and quite accurately pronounce foreign place and street names. For example, the English voice can read French street names.

Note: If you select a human voice, this will only be able to announce commands, but not street names. If you would like street names to be announced, you will need to select a computer voice.

Internal and external speakers

Your TomTom GO contains a high quality speaker. This is used to play all the sounds on your GO unless you select to play some sounds through external speakers.

The following types of sounds can be played through the speakers as listed below:

• Spoken instructions and warnings:

• The speaker inside your GO

• An external Bluetooth® Hi-Fi headset or speakers

• Using an audio cable.

• Music

• The speaker inside your GO

• An external Bluetooth® Hi-Fi headset or speakers

• Using an audio cable.

• Phone calls

• The speaker inside your GO

Note: If you wish to use an audio cable, a Windshield Mount with an audio connector is available as an accessory. Your car stereo needs a line-in connector. Not all car stereos have line-in connectors. Check the instructions for your car stereo for more information.

Using Bluetooth® Hi-Fi speakers

Your GO can play sound through Bluetooth® Hi-Fi speakers, such as a

Bluetooth® Hi-Fi headset, or a car stereo which uses Bluetooth®.

To play sound over Bluetooth® Hi-Fi speakers, do the following:

1. Tap Speaker preferences in the Preferences menu.

Tap this button to change the speaker settings.

Speaker preferences

2. To play spoken instructions through a Bluetooth device, select Bluetooth

Hi-Fi device.

3. To play music through a Bluetooth device, select Bluetooth Hi-Fi device.

4. Tap Done.

5. Your GO asks you to confirm that you want to use an external Bluetooth®

Hi-Fi speaker. Tap YES.

Your GO will start searching for Bluetooth® Hi-Fi devices.

6. Select your Bluetooth® Hi-Fi device from the list of devices found by your

GO.

Your GO will try to establish a Bluetooth® connection with your device.

Your device may require you to enter a password on your GO before a

Bluetooth® connection can be established. See the documentation for your

Bluetooth® Hi-Fi device for more information.

Once connected, sound will be played through the external Bluetooth® Hi-Fi device.

If your GO cannot establish a Bluetooth® connection, then all sound will be played through the internal speaker or through the audio cable if it is connected.

27. Hands-free calling

If you have a mobile phone with Bluetooth®, you can use your TomTom GO to make phone calls and send and receive messages.

Note: Not all phones are supported or compatible with all features. For more information, go to tomtom.com/phones/compatibility.

Connecting to Your Phone

First you must establish a connection between your mobile phone and your

TomTom GO.

Tap Mobile phone in the Main Menu and then follow the instructions on the screen.

You only need to do this once, after which your TomTom GO will remember your phone.

Your Phone Book

You can copy your phonebook from your mobile phone to your TomTom GO so that you can make calls with just a few taps on the screen.

This is the safest way to make hands-free calls.

Note: You can copy your phonebook to your TomTom GO at any time. From the Mobile phone menu, tap Get numbers from phone.

Not all phones can transfer their phonebook to your GO. For more information, visit www.tomtom.com/phones/compatibility.

Making a Call

Once you have established a connection with your phone, you can start making calls.

1. Tap Mobile phone in the Main Menu.

2. Tap Call.

Note: Make sure that your phone is currently selected. The current phone is shown at the bottom of the screen.

3. Tap Number to enter a number to call.

4. Do one of the following:

• Tap Home to call your Home location. If you have not entered a number for your Home location this button is unavailable. To enter a number, tap

Change Home number in the Phone preferences menu.

• Tap Number to enter a number to call.

• Tap Point of Interest to choose a Point of Interest (POI) to call. If your GO knows the phone number of a POI, this is shown next to the POI.

• Tap Phonebook entry to select a contact from your phonebook.

Note: If you have not copied your phonebook to your TomTom GO, the button

Phonebook entry is unavailable.

• Tap Recently dialed to select from a list of people or numbers you have called recently using your GO.

• Tap Recent caller to select from a list of people or numbers who called you recently. Only calls you have received on your GO are saved in this list.

Receiving a call

When someone calls you, the caller’s name and phone number are shown.

Tap the screen to accept or reject the call.

Tip

: This button also appears in the Driving view while a call is active. Tap this button in the Driving view while making a call, to view the Call... menu.

Call...

Auto-Answer

You can tell your TomTom GO to answer every call automatically after a certain time. Tap Phone preferences in the mobile phone menu, then tap

Auto-answer preferences.

Select when your TomTom GO will automatically answer your calls.

Sharing your TomTom GO

To add more phones, do the following. You can establish connections for up to 5 mobile phones.

1. Tap Mobile phone in the Main Menu.

2. Tap Connect to your phone.

3. Tap Find other phone... and follow the instructions on the screen.

To switch between phones, tap Connect to your phone and then select your phone from the list.

Call menu

Call...

When you open the Call menu, the following buttons are available:

Tap this button to make a call from your mobile phone.

This button also appears in the Driving view while a call is active. Tap this button in the Driving view to open the Call menu where you can see the details of the caller or end the call.

Tip

: Tap this button in the Driving view while making a call, to view the Call menu.

Tap this button to redial a telephone number using your mobile phone.

REDIAL

Tap this button to read or write a message.

Read/Write message

Tap this button to configre how your TomTom GO communicates with your mobile phone.

Phone preferences

Tap this button to load the contacts and phone numbers from your mobile phone onto your TomTom GO.

Get numbers from phone

Tap this button to manage the mobile phones that will be connected to your TomTom GO. You can add a profile for up to five different mobile phones.

Manage phones

28. Preferences

You can change the way your TomTom GO looks and behaves.

Tap Change preferences in the Main Menu.

Hidden buttons and features

When you first start using your TomTom GO, all the buttons are shown in the menu.

The buttons for the more advanced features can be hidden. This is a useful option because you are unlikely to use certain features very often.

Show fewer menu options

Tap this button in the Preferences menu, to reduce the number of buttons that are shown.

You might want to do this so that only frequently used buttons are shown.

When you need to use the buttons that are hidden, you can press Show

ALL menu options in the Preferences menu to show all buttons.

Tap this button in the Preferences menu, to show all the buttons available on your TomTom GO.

Show ALL menu options

Use night colors / Use day colors

Use night colors

Tap this button to reduce the brightness of the screen and show darker colors on the map.

When should I use this?

When it’s dark, it is easier to see the screen if the display on your GO is not brightly lit.

To change back to a brighter screen showing brighter colors on the map, tap Use day colors.

Use day colors

Can my GO make this change automatically?

Yes. Your GO has a light sensor to tell when it is getting dark.

To change to night and day colors automatically, tap Brightness preferences in the Preferences menu. Then select Switch to night view when dark.

Show POI on map

Show POI on map

Tap this button to set which categories for the Points of Interest (POIs) should be shown on the map:

1. Tap Show POIs on map in the Preferences menu.

2. Select the POI categories to display on the map.

Tap Find to search for a POI category.

3. Tap Done.

The POIs you have selected are shown as symbols on the map.

Safety preferences

Safety preferences

Tap this button to set the following safety preferences:

• Hide most menu options while driving

• Suggest driving breaks

• Show safety reminders

• Warn when near places of worship or schools

• Warn when driving faster than allowed

• Warn when driving faster than a set speed

• Warn not to leave the device in the car

If you select one or more of the warnings, you will also be asked to select a sound to be played whenever a warning is displayed.

Select whether or not your TomTom GO should warn you about which side of the road you should be driving on.

Decide if you want the map display to be turned off in special circumstances and press Done.

What happens when I use the Turn off map display option?

When you turn off the map display, instead of seeing your position on a map in the Driving View, you will only see information about the next instruction.

Tap the button and select an option for when the map should be turned off.

These are the options:

• Always - The map will not be shown and you will only see information about the next instruction and arrows showing direction.

• Above a certain speed - you set the speed at which point the map will be turned off. This option is useful for situations when the map might be distracting, such as when you are driving fast.

• Never - the map is never turned off.

Voice preferences

Voice preferences

Tap Voice preferences to manage your TomTom voices. The following options are available:

• Change voice - tap this button to change the voice that gives you instructions.

A wide range of recorded human voices and computer voices are available.

• Disable voice - tap this button to disable the use of voices. To enable voices, tap Enable.

• Speech preferences - tap this button to set the situations when your

TomTom will read instructions or warnings aloud.

• Record voice - tap this button to record your own voice for use by your

TomTom. The procedure takes about fifteen minutes, during which time you will say all the commands that are used by your TomTom GO.

In the Preferences menu, tap Voice preferences, then tap Record voice and follow the instructions for recording your voice.

• Disable recorded voice

• Enable recorded voice

• Download voice - tap this button to download new voices from

TomTom Services and transfer them to your TomTom.

Turn off sound / Turn on sound

Turn off sound

Tap this button to turn off sound. If you turn off the sound, warnings for upcoming POIs are also turned off.

The button changes to Turn on sound.

Tips

To change the volume, tap Volume preferences in the Preferences menu.

To change the volume quickly while you are driving, tap the bottom lefthand section of the Driving View and move the slider.

To change the voice being used by your GO, tap Change voice in the Voice preferences menu.

Can I still use my GO to make hands-free calls when the sound is turned off?

Yes. Turning the sound off does not affect hands-free calling, meaning that you will still be able to talk to and hear the caller.

Volume preferences

Tap this button to change the volume.

Volume preferences

Can my GO change the volume depending on how noisy it is in the car?

Select Link volume to noise level and your GO will change the volume according to the background noise. The noise level is constantly monitored by the microphone on your GO. If there is a lot of noise in the car, your GO will automatically increase the volume.

For example, if you are driving on the highway, which is often very noisy, the volume level on your GO will be increased. When you are driving more slowly again, the volume level will be lowered by your GO.

Manage Favorites

Tap this button to rename or delete Favorites.

To find a Favorite quickly, tap Find, then start to type the name of the

Favorite. As soon as the Favorite is shown in the list, you can select it.

Manage

Favorites

Change Home location

Tap this button to set or change your Home location.

Change Home location

Manage maps

Do I need to use my actual home address for the Home location?

No. Your Home location can be a place you go often, for example, your office.

It can be your actual home address, but it can also be any address you like.

Why should I set a Home location?

Having a Home location means that you have a quick and easy way to navigate there, by tapping the Home button in the Navigate to... menu

This button may only be available if all menu options are shown. To show all menu options, tap Show ALL menu options in the Preferences menu.

Manage maps

Tap this button to do the following:

• Switch map - tap this button to change the map you are using.

• Download free map corrections - tap this button to download map corrections provided as part of the Map Share service.

Use TomTom HOME to make backups, download, add and delete maps from your navigation device.

Manage POIs

This button may only be available if all menu options are shown. To show all menu options, tap Show ALL menu options in the Preferences menu.

Manage POIs

Tap this button to do the following:

• Set alerts for when you are near POIs.

For example, your GO can tell you when there is a gas station nearby.

• Create your own POI categories and add POIs to them.

For example, you could create a category of POIs called “Friends”, and add all your friends’ addresses as POIs in the category. You can even add your friends’ phone numbers with their address so you can call them from your GO.

The following buttons are available:

• Add POI - tap this button to add a location to a POI category you have created.

• Warn when near POI - tap this button to be warned when you approach a POI. You can select the types of POI for which you wish to be warned.

• Delete POI - tap this button to delete a POI you created.

• Edit POI - tap this button to edit the details of a POI you created.

• Add POI category - tap this button to create a new POI category.

• Delete POI category - tap this button to delete a POI category you created.

Change car symbol

This button may only be available if all menu options are shown. To show all menu options, tap Show ALL menu options in the Preferences menu.

Tap this button to select a car symbol that will be used to show your current position in the Driving view.

Additional car symbols can be downloaded using TomTom HOME.

Change car symbol

Change 2D/3D display / Turn on 2D display

Turn on 2D display

Tap Turn on 2D display to change the perspective for viewing the map.

For example, the 2D view shows a two dimensional view of the map as though viewed from above.

To switch the view to a three dimensional perspective, tap Change 2D/3D

display and select a view from the list.

Change 2D/3D display

When should I use this?

In some situations, it is easier to see the map from above. Perhaps if the road network is complicated or for times when you are walking while using your GO to navigate.

Show/Hide lane images

This button may only be available if all menu options are shown. To show all menu options, tap Show ALL menu options in the Preferences menu.

Tap this button to show or hide the arrows that warn you which lane you need to be in to navigate an approaching road exit or intersection.

Show lane images

Change map colors

This button may only be available if all menu options are shown. To show all menu options, tap Show ALL menu options in the Preferences menu.

Tap this button to select the color schemes for day and night map colors.

You can also download more color schemes from TomTom Services.

Change map colors

Brightness preferences

This button may only be available if all menu options are shown. To show all menu options, tap Show ALL menu options in the Preferences menu.

Brightness preferences

Tap this button to set the brightness of the screen.

Move the sliders to set the brightness separately for day map colors and for night map colors.

You can also set these options:

• Turn brightness down when dark - your GO uses a light sensor to detect the background light level. If this option is selected, as it gets darker, your GO reduces the brightness of the screen so that it is not distracting.

• Switch to night view when dark - your GO uses a light sensor to detect the background light level. If this option is selected, when it gets dark, your GO uses night colors for the Driving View.

You can set the map color scheme by tapping Change map colors.

Status bar preferences

This button may only be available if all menu options are shown. To show all menu options, tap Show ALL menu options in the Preferences menu.

Status bar preferences

Tap this button to select the information shown on the status bar:

• How should the status bar be displayed?

Horizontal - If you choose this option, the status bar will be shown at the bottom of the Driving view.

Vertical - If you choose this option, the status bar will be shown at the right-hand side of the Driving view.

• Remaining time - the estimated time left until you reach your destination.

• Remaining distance - the distance left until you reach your destination.

• Current time

• Arrival time - your estimated arrival time.

• Speed

• Direction

• Show lane guidance

• Show current street name

• Show leeway to arrival time - your GO shows how late or early you will be compared with the preferred arrival time that is set during the planning of a route.

• Show max speed next to speed - only available when speed (above) is also selected.

Note: If the speed limit for the road you are on is available, it is shown next to your speed.

If you drive faster than the speed limit, your speed is shown in red.

• Show compass

Automatic zooming

This button may only be available if all menu options are shown. To show all menu options, tap Show ALL menu options in the Preferences menu.

Tap this button to enable or disable automatic zooming in the Driving View.

Automatic zooming

Quick menu preferences

This button may only be available if all menu options are shown. To show all menu options, tap Show ALL menu options in the Preferences menu.

Quick menu preferences

Tap this button to choose up to six buttons to be used in the Quick menu.

The Quick menu button enables easy access for your most commonly used buttons.

The buttons you assign for use with the Quick menu, are shown in the

Driving View.

Guided tours

This button may only be available if all menu options are shown. To show all menu options, tap Show ALL menu options in the Preferences menu.

Tap this button to show one of the Guided tours on how to use your

TomTom GO.

Guided tours

Street name preferences

This button may only be available if all menu options are shown. To show all menu options, tap Show ALL menu options in the Preferences menu.

Street name preferences

Tap this button to set the information that is shown on the map in the

Driving View. The following options are available:

• Show house number before street name

• Show street names - if you are using a computer voice for spoken instructions and have selected that street names should be read aloud, you do not need to select this option, since the street names will be read aloud even though this option is not selected.

• Show next street name

• Show current street name on map

• Show next freeway / signpost - if available, the road sign to follow or the name of the next major road on your route is shown at the top of the screen in the Driving View.

Set units

This button may only be available if all menu options are shown. To show all menu options, tap Show ALL menu options in the Preferences menu.

Set units

Tap this button to set the type of units that will be shown for the following:

• Distance

• Time

• Latitude and longitude

• Temperature

• Air pressure

Operate left-handed / Operate right-handed

This button may only be available if all menu options are shown. To show all menu options, tap Show ALL menu options in the Preferences menu.

Operate lefthanded

Tap this button to move important buttons, for example, the Done and

Cancel buttons as well as the zoom bar, to the left hand side of the screen.

This makes it easier to tap the buttons with your left hand without blocking the screen.

To move the buttons back to the right hand side of the screen, tap Operate

right-handed.

Keyboard preferences

Keyboard preferences

You use the keyboard to enter your destination or to find an item in a list, such as a POI.

Tap this button to select the size of the keys on the keyboard and the keyboard layout. You can select from two sizes:

• Large keyboard

• Small keyboard

Three keyboard layouts are available:

• ABCD keyboard

• QWERTY keyboard

• AZERTY keyboard

Planning preferences

This button may only be available if all menu options are shown. To show all menu options, tap Show ALL menu options in the Preferences menu.

Planning preferences

Tap this button to set the kind of route planned when you select a destination.

The following options are available:

• Ask me every time I plan

• Always plan fastest routes

• Always plan shortest routes

• Always avoid freeways

• Always plan walking routes

• Always plan bicycle routes

• Always plan for limited speed

Tap the IQ Routes button to enable or disable IQ Routes.

IQ Routes is used to plan the best possible route - taking into account the real average speeds measured on the roads.

Then set how your GO should handle the following when planning a route:

• Toll roads on the route

• Ferry crossings on the route

• HOV lanes on the route

• Unpaved roads

You can then set if the route summary screen closes automatically after you have planned a route. If you select No, you have to tap Done to close the route summary screen.

Replanning preferences

Select whether or not you want your TomTom GO to replan your route when a faster route is found while you drive. This might occur due to changes in the traffic situation.

Set owner

This button may only be available if all menu options are shown. To show all menu options, tap Show ALL menu options in the Preferences menu.

Set owner

Tap this button to enter your name and address as the owner of your GO and to change or delete a 4-digit password for your GO.

Note: You can only change or delete a 4-digit password on your

TomTom GO.

You can create a 4-digit password for your GO using TomTom HOME:

1. Connect your GO to your computer and turn on your GO and your computer.

TomTom HOME starts automatically.

2. Click on Operate my GO in TomTom HOME.

Your GO appears and can be controlled using TomTom HOME.

3. From the Main Menu, click Change preferences.

4. Click Set Owner. You can now set a 4-digit password for your GO.

You can only create a 4-digit password using TomTom HOME.

Speaker preferences

This button may only be available if all menu options are shown. To show all menu options, tap Show ALL menu options in the Preferences menu.

Speaker preferences

Tap this button to select which speakers are used by your TomTom GO for spoken instructions and also music. The following options are available:

• Internal speaker

• Bluetooth Hi-Fi device

• Line-out (audio cable)

Start-up preferences

This button may only be available if all menu options are shown. To show all menu options, tap Show ALL menu options in the Preferences menu.

Start-up preferences

Tap this button to select what happens when your GO starts. The following options are available:

• Continue where I left off - your GO starts and shows the last screen that was shown when you turned off the device.

• Show the Driving View - your GO starts and shows the Driving View.

• Ask for a destination - your GO starts with Navigate to... menu. You can enter a destination immediately.

• Show the Main Menu - your GO starts with the Main Menu.

• Start Slideshow - your GO starts by showing a slideshow of the images stored there. To interrupt the slideshow, tap the screen.

You are then asked if you want to change the picture that is shown whenever you start your GO.

Tap No to finish or tap Yes to see the photos stored on your GO and tap on a photo to select that photo for use as your start-up picture.

Bluetooth preferences

This button may only be available if all menu options are shown. To show all menu options, tap Show ALL menu options in the Preferences menu.

Bluetooth preferences

Tap this button to manage Bluetooth functionality on your TomTom GO.

Important

: In places such as hospitals and on airplanes, you are required to switch off Bluetooth for all your electronic devices.

You can select the following options:

• Disable Bluetooth/Enable Bluetooth - switch Bluetooth on or off for your GO. If you disable Bluetooth, all the other options are unavailable.

• Connect to Bluetooth device - connect to another device that uses

Bluetooth.

• Disable hands-free calling/Enable hands-free calling - switch handsfree calling on or off for your GO.

• Disable wireless data/Enable wireless data - enable or disable the transfer of wireless data.

Flight mode

Flight Mode

Tap this button to enable or disable all wireless connections on your navigation device, such as Bluetooth and GSM mobile communications.

This is important when entering areas, such as a hospital, where you must turn off devices that transmit radio signals.

Send/Receive files

This button may only be available if all menu options are shown. To show all menu options, tap Show ALL menu options in the Preferences menu.

Tap this button to send or receive files, such as itineraries and voices, using your GO with other Bluetooth devices.

Send/Receive files

My TomTom account

This button may only be available if all menu options are shown. To show all menu options, tap Show ALL menu options in the Preferences menu.

MyTomTom account

Tap this button to log in to your TomTom account.

If you have more than one TomTom account or if several people are sharing the same TomTom GO, you can switch to another TomTom account.

Battery saving preferences

This button may only be available if all menu options are shown. To show all menu options, tap Show ALL menu options in the Preferences menu.

Battery saving preferences

Tap this button to configure your GO to conserve power when possible. The following options are available:

• Never turn off screen

• Turn off screen between instructions

• Always turn off screen

Then select whether or not you want to Switch off when external power is

lost.

Change language

Change language

Tap this button to change the language used for all the buttons and messages you see on your GO.

You can choose from a wide range of languages. When you change the language, you are also given the opportunity to change the voice.

Set clock

Set clock

Tap this button to select the type of clock that is shown and set the time.

The easiest way to set the time is by tapping the Sync button. Your GO will then take the time from GPS information.

Note: After using Sync to set the time, you may have to adjust the hours depending on your time zone. Your GO works out your time zone and always keeps the time correct using GPS information.

You can only use Sync if you have GPS reception, so you cannot set the clock in this way when you are indoors.

Hide tips / Show tips

This button may only be available if all menu options are shown. To show all menu options, tap Show ALL menu options in the Preferences menu.

Tap this button to stop your GO from showing tips.

To turn tips on again, tap Show tips.

Hide tips

Safety driving menu

Safety driving menu

Tap this button to set the button shown in the bottom right-hand corner of the Safety Driving Menu.

By default, Add favorite is shown in this position. You can change this to, for example, show the trip statistics for the day, start a hands-free call to a specfic number, or add a position to an Itinerary.

Reset factory settings

This button may only be available if all menu options are shown. To show all menu options, tap Show ALL menu options in the Preferences menu.

Reset factory settings

Tap this button to restore the factory settings to your TomTom GO.

All your settings, including Favorites, your Home location, warnings for

POIs and any Itineraries you have created are deleted.

Important

: The list of orders and messages, all reporting information, and all messages are deleted.

29. Points of Interest

Points of Interest or POIs are useful places on the map. Here are some examples:

• Restaurants

• Hotels

• Museums

• Parking garages

• Gas stations

Note: You can report missing POIs or edit existing POIs using Map Share and share your corrections with the Map Share community.

Creating POIs

1. Tap the screen to bring up the main menu.

2. Tap Change preferences.

3. Tap Manage POIs.

This button may only be available if all menu options are shown. To show all menu options, tap Show ALL menu options in the Preferences menu.

4. Before you can add a POI, you have to create at least one POI category.

Every POI is assigned to a POI category. You can only add POIs to POI categories you have created yourself.

Tap Add POI category.

Add POI category

5. Enter a name for your POI category, for example, ‘Friends’ or ‘Favorite restaurants’. Then select a marker for your POI category.

6. Tap Add POI.

Tap this button to add a POI.

Add POI

7. You are asked to name the POI.

8. Select the POI category in which you want to add the POI.

Home

Favorite

Address

9. Select the location of your POI from the list below.

You can set your Home location as a POI.

If you want to change your Home location, you can create a POI of the

Home location before you change it.

You can create a POI from a Favorite.

You can only create a limited number of Favorites. If you want to create more Favorites you have to delete some Favorites first. Before you delete a Favorite, make it into a POI so that you don’t lose the address.

You can specify an address to be a POI. When you enter an address, you can choose from four options.

• City center

• Street and house number

• Zip code

• Crossing or intersection

Select a POI location from a list of places you have recently used as destinations.

Recent destination

You can add a Point of Interest (POI) as a POI. For example, if you are creating a category of POIs for your favorite restaurants, use this option instead of entering the addresses of the restaurants.

Point of

Interest

My location

Tap this button to add your current position as a POI.

For example, if you stop somewhere you like, while you are there you can tap this button to create the POI.

Tap this button to create a POI using the map browser.

Select the location of the POI using the cursor, then tap Done.

Point on map

Tap this button to create a POI by entering latitude and longitude values.

Latitude

Longitude

Tap this button to select your last recorded position as your destination.

This may be useful if your GO is unable to maintain a strong GPS signal, for example, when you drive through a long tunnel.

Position of last stop

Note: You can report missing POIs or edit existing POIs using Map Share and share your corrections with the Map Share community.

Navigating to a POI

You can use a POI as your destination. For example, if you are traveling to an unfamiliar city, you could choose a POI to help find a parking garage.

1. Tap the screen to bring up the main menu.

2. Tap Navigate to... in the Main Menu.

3. Tap Point of Interest.

4. Tap POI in city.

5. Narrow your choice of POIs by selecting the area where the POI is located.

You can select one of these options:

• POI near you - to choose from a list of POIs near to your current location.

• POI in city - to find a POI in a particular town or city.

• POI near Home - to choose from a list of POIs near to your Home location.

You can select from a list of POIs which are along your route or close to your destination. Choose from one of these options:

• POI along route

• POI near destination

Note: The last POI you viewed is also shown so that you can plan a route there more quickly.

6. Type the name of the town you want to visit and select the town when it appears in the list.

7. Select the category of POI:

Tap Any POI category to search for a POI by category name.

Tap the category of POI, if it is shown.

Tap the arrow to choose from the complete list of categories. Select the category from the list or start to type the name of the category and select it when it appears in the list.

8. Tap Parking garage.

9. From the list of POIs shown, select the POI you want to navigate to.

The table below explains the distances listed next to each POI.

POI near you

POI in city

Distance from your current location

Distance from the city center

POI near Home Distance from your Home location

POI along route

Distance from your current location

POI near destination

Distance from your destination

If you know the name of the POI, tap Find and type the name. Select it from the list when it is shown.

The next screen shows more detailed information including the location of the POI on the map and the phone number of the POI, if available.

Tap Select to confirm you want to plan a route to this POI.

Once you have selected a POI, the route to the POI is calculated by your

TomTom GO.

Showing POIs on the map

1. Tap Show POIs on map in the Preferences menu.

Show POI on map

2. Select the POI categories to display on the map.

Tap Find to search for a POI by name.

3. Tap Done.

The POIs you have selected are shown as symbols on the map.

Calling a POI

Your TomTom GO knows the phone numbers for many POIs. You can, for example, call a restaurant to book a table.

1. In the Main Menu, tap Mobile phone.

2. Tap Call....

3. Tap Point of interest.

4. Select the POI you want to call.

You are shown the location on the map and telephone number.

5. Tap Dial.

Your TomTom GO dials the phone number using your mobile phone.

How can I set warnings for POIs?

1. Tap the screen to bring up the main menu.

2. Tap Change preferences.

3. Tap Manage POIs.

Note: The Manage POIs button is only available when all menu buttons are shown. To show all menu buttons, tap Show ALL menu options in the

Preferences menu.

4. Tap Warn when near POI.

Tap this button to receive a warning when you travel near to the location of a POI.

Warn when near POI

5. Select the category of POI you want to be warned about.

Select the category from the list or start to type the name of the category and select it when it is shown in the list.

6. Set how close the POI should be when you receive a warning.

7. Choose the warning sound for the category of POI you selected.

Managing POIs

Tap Manage POIs from the Preferences menu.

Manage POIs

Note: The Manage POIs button is only available when all menu buttons are shown. To show all menu buttons, tap Show ALL menu options in the

Preferences menu.

You can, for example, do the following:

• Create your own POI categories and add POIs to them.

• Set warnings when you get close to POIs.

Why would I want to create my own POIs?

A POI acts like a shortcut - once you have saved a location as a POI you never have to type the address of that POI again. But when you create a POI you can save more than just the location.

• Phone number - when you create a POI, you can save a phone number with it.

• Categories - when you create a POI you have to put it in a category.

For example, you could create a category of POIs called ‘Favorite restaurants’.

With each POI, save their phone number so that you can call them to reserve a table.

Note: You can report missing POIs or edit existing POIs using Map Share and share your corrections with the Map Share community.

30. Itinerary Planning

What is an Itinerary?

An Itinerary is a plan for a trip including more locations than your final destination.

An Itinerary can include the following items:

• Destination - a location on your trip where you want to stop.

• Waypoint - a location on your trip you want to travel through without stopping.

Destinations are shown using this symbol.

Waypoints are shown using this symbol.

When would I use an Itinerary?

You could use an Itinerary for trips such as:

• A road trip through a country with lots of stops.

• A two day car trip with an overnight stop.

• A short drive which passes by Points of Interest.

In all these examples you could tap Navigate to... for each place. However, if you use an Itinerary, you can save time by planning everything in advance.

Creating an Itinerary

1. Tap the screen to bring up the main menu.

2. Tap Itinerary planning.

The Itinerary planning screen opens. At first, there are no items on the

Itinerary.

Itinerary planning

Note: This button may only be available if all menu options are shown. To show all menu options, tap Show ALL menu options in the Preferences menu.

3. Tap Add and select a location.

Tip:

You can add items to your Itinerary in any order and rearrange the order later.

Following an Itinerary

When you use an Itinerary to navigate, the route will be calculated to the first destination on the Itinerary. Your TomTom GO calculates the remaining distance and time to the first destination and not for the whole Itinerary.

As soon as you start to use an Itinerary, the route is calculated from your current position. You do not need to set a departure point.

When you have passed a waypoint or reached a destination, it is marked as visited.

Waypoints are shown on the map. Your GO will not warn you when you are approaching a waypoint or when you arrive at a waypoint.

Organizing an Itinerary

Tap an item on your Itinerary to open a page of buttons for editing the item.

The buttons shown below are available.

Mark as waypoint

Mark as destination

Mark ‘visited’

Mark ‘to visit’

You can change a destination into a waypoint using this button.

Remember that waypoints are points on your trip to your destination that you want to pass and destinations are places where you want to stop.

This button is only shown if the item you tapped is a destination.

You can change a waypoint into a destination using this button.

Remember that destinations are places where you want to stop, and waypoints are points on your trip to your destination that you want to pass.

This button is only shown if the item you tapped is a waypoint.

Tap this button to miss out part of your Itinerary. Your GO will ignore this item and all the items before it in the Itinerary.

It will navigate you to the next item in the Itinerary.

This button is only shown if you are still due to visit this item.

Tap this button to repeat part of your Itinerary. Your GO will navigate you to this item followed by the rest of the items in the Itinerary.

This button is only shown if you have already visited this item.

Move item up

Tap this button to move the item up the Itinerary.

This button is unavailable if the item is at the top of the Itinerary.

Tap this button to move the item down the Itinerary.

This button is unavailable if the item is at the bottom of the Itinerary.

Move item down

Tap this button to see the location of the item on the map.

Show on map

Tap this button to delete the item from the Itinerary.

Delete item

Start Using an Itinerary

Tap Options, then tap Start navigation.

To save an Itinerary, tap Save Itinerary.

To load a saved Itinerary, tap Load Itinerary.

To create a new Itinerary, tap New Itinerary and to delete one, tap Delete

Itinerary.

31. Help me

Help me provides an easy way to navigate to emergency services centers and other specialist services and contact them by phone.

For example, if you are involved in a car accident, you could use Help me to call the nearest hospital and tell them your exact location.

Tip

: If you do not see the Help me button in the Main Menu, tap Show ALL

menu options in the Preferences menu.

How do I use Help me to phone a local service?

You can use Help me to search for a service center, make contact by phone and inform the center about the precise details of your current location.

When you search for a service center, you are shown a list of nearby locations.

Select one of the centers in the list to view their address and phone number and your current location on the map.

If your phone is connected to your GO, your GO automatically dials the phone number.

To use Help me to locate a service center, contact the center by phone and navigate from your current location to the center, do the following:

1. Tap the screen to bring up the main menu.

2. Tap Help me.

3. Tap Phone for help.

4. Select the type of service you require, for example, Nearest hospital.

5. To dial, select a center from the list, the nearest is shown at the top of the list.

Once the call is answered your GO shows your position on the map along with a description of the location. This helps you explain where you are while making a call.

6. To navigate your way to the center on foot, tap Walk there.

Your GO starts guiding you to your destination.

Options

Note: In some countries, information may not be available for all services.

Tap this button to find the contact details and location of a service center.

Phone for help

Tap this button to navigate your way by car to a service center.

Drive to help

Tap this button to navigate your way on foot to a service center.

Walk to help

Where am I?

Tap this button to see your current location on the map. You can then tap

Phone for help and select the type of service you want to contact and tell them your exact location.

Tap this button to read the British Red Cross First Aid guide.

First Aid

Guide

Tap this button to read a selection of useful guides.

Other guides

32. Introducing TomTom HOME

TomTom HOME is a free application for your computer that helps you manage the contents of your TomTom GO navigation device. It is a good idea to frequently connect to HOME to ensure you always have the latest updates on your device.

You can, for example, do the following:

• Manage maps, voices, POIs and more.

• Buy TomTom services and manage your subscriptions.

• Update your device automatically with the latest software and services.

• Make and restore backups.

• Read the full version of the user manual.

Tip

: We recommend using a broadband internet connection whenever you connect to HOME.

It is a good idea to make regular backups of your navigation device using

HOME.

Installing TomTom HOME

To install TomTom HOME on your computer, do the following:

1. Connect your computer to the internet.

2. Connect your device to your computer using the USB cable, then switch your device on.

HOME starts to install.

Note: If HOME does not install automatically, you can also download it from

tomtom.com/home

TomTom HOME starts automatically when the navigation device is switched on while the device is connected to your computer.

MyTomTom Account

To download content and services using TomTom HOME, you need a

MyTomTom account. You can create an account when you start using

TomTom HOME.

33. Addendum

Important Safety Notices and Warnings

Global Positioning System

The Global Positioning System (GPS) is a satellite-based system that provides location and timing information around the globe. GPS is operated and controlled under the sole responsibility of the Government of the United

States of America, which is responsible for its availability and accuracy. Any changes in GPS availability and accuracy, or in environmental conditions, may impact the operation of your TomTom device. TomTom does not accept any liability for the availability and accuracy of GPS.

Use with Care

Use of a TomTom device for navigation still means that you need to drive with due care and attention.

Aircraft and Hospitals

Use of devices with an antenna is prohibited on most aircraft, in many hospitals and in many other locations. A TomTom device must not be used in these environments.

Taking care of your TomTom device

Do not leave your TomTom device or TomTom accessories on view when you leave your car. They may become an easy target for thieves.

You can set a password for your device which must be entered every time you start your device.

We recommend that you use the safety preferences on your TomTom device, where available. The safety preferences are available in the Preferences menu.

Take care of your TomTom device and clean it correctly.

• Use a soft cloth to wipe the screen of your device; do not use any liquid cleaners.

• If your device gets wet, dry it with a soft cloth.

• Do not open the casing of your device under any circumstances. Doing so may be dangerous and will invalidate your warranty.

• If your device includes a memory card, do not use the memory card with any device other than a TomTom device. Other devices may damage the memory card.

• Do not expose your device to high or low temperatures, which can cause permanent damage. For example, don’t leave it in the car on hot summer days or during cold winter nights.

Battery

This product uses a Lithium-Polymer battery. Do not use it in a humid, wet and/or corrosive environment. Do not put, store or leave your product in or near a heat source, in a high temperature location, in strong direct sunlight, in a microwave oven or in a pressurized container, and do not expose it to temperatures over 60 C (140 F). Failure to follow these guidelines may cause the Lithium-Polymer battery to leak acid, become hot, explode or ignite and cause injury and/or damage. Do not pierce, open or disassemble the battery.

If the battery leaks and you come into contact with the leaked fluids, rinse thoroughly with water and seek medical attention immediately. For safety reasons, and to prolong the lifetime of the battery, charging will not occur at low (below 0 C/32 F) or high (over 45 C/113 F) temperatures.

Temperatures: Standard operation: -10 C (14 F) to +55 C (131 F); short period storage: -20 C (-4 F) to + 60 C (140 F); long period storage: -20 C (-4 F) to

+25 C (77 F).

THE LITHIUM-POLYMER BATTERY CONTAINED IN THE PRODUCT

MUST BE RECYCLED OR DISPOSED OF PROPERLY. USE YOUR

TOMTOM ONLY WITH THE SUPPLIED DC POWER LEAD (CAR

CHARGER/BATTERY CABLE) AND AC ADAPTER (HOME CHARGER)

FOR BATTERY CHARGING.

To recycle your TomTom unit please see your local approved TomTom service center.

The stated battery life is a maximum possible battery life. The maximum battery life will only be achieved under specific atmospheric conditions. The estimated maximum battery life is based on an average usage profile.

For tips on extending the battery life, go to the FAQ listed below for your country:

AU: www.tomtom.com/8703

CZ: www.tomtom.com/7509

DE: www.tomtom.com/7508

DK: www.tomtom.com/9298

ES: www.tomtom.com/7507

FI: www.tomtom.com/9299

FR: www.tomtom.com/7506

HU: www.tomtom.com/10251

IT: www.tomtom.com/7505

NL: www.tomtom.com/7504

PL: www.tomtom.com/7503

PT: www.tomtom.com/8029

RU: www.tomtom.com/10250

SE: www.tomtom.com/8704

UK: www.tomtom.com/7502

US: www.tomtom.com/7510

SPECIAL NOTE REGARDING DRIVING IN CALIFORNIA AND MINNESOTA

California Vehicle Code Section 26708 (a) (1) provides that “No persons shall drive any motor vehicle with an object or material placed, displayed, installed, affixed or applied upon the windshield or side or rear windows.” Drivers in

California should not use a suction mount on their windshield, side or rear windows.

Note: this section of the California Vehicle Code applies to anyone driving in

California, not just California residents.

Minnesota State Legislature Statutes Section 169.71, subdivision 1, section 2 provides that “A person shall not drive or operate with any objects suspended

between the driver and the windshield other than sun visors and rearview mirrors and electronic toll collection devices.”

Note: this Minnesota Stature applies to anyone driving in Minnesota, not just

Minnesota residents.

TomTom Inc. bears no responsibility for any fines, penalties or damage that may be incurred by disregarding this notice. While driving in any state with windshield mounting restrictions, TomTom recommends the use of the supplied Adhesive Mounting Disk or its Alternative Mounting Kit, which includes multiple options for mounting TomTom devices on the dashboard and using the air vents. See www.tomtom.com for more information about this mounting option.

FCC Information for the User

This product contains a transmitter which must not be co-located or simultaneously operated in conjunction with any other transmitter.

Radio and Television Interference

This equipment radiates radio frequency energy and if not used properly - that is, in strict accordance with the instructions in this manual - may cause interference to radio communications and television reception.

This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation distance between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment.

Important

This equipment was tested for FCC compliance under conditions that included the use of shielded cables and connectors between it and the peripherals. It is important that you use shielded cables and connectors to reduce the possibility of causing radio and television interference. Shielded cables suitable for the product range can be obtained from an authorised dealer. If the user modifies the equipment or its peripherals in any way, and these modifications are not approved by TomTom, the FCC may withdraw the user’s right to operate the equipment. For customers in the USA, the following booklet prepared by the Federal Communications Commission may be of help: “How to Identify and Resolve Radio-TV Interference Problems”. This booklet is available from the US Government Printing Office, Washington, DC

20402. Stock No 004-000-00345-4.

FCC Declaration of Conformity

Tested to comply with FCC Standards for Home or Office Use

FCC ID: S4L 4CH6

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

Responsible party in North America

TomTom, Inc., 150 Baker Avenue Extension, Concord, MA 01742

Tel: 1-866-459-3499

This Document

Great care was taken in preparing this manual. Constant product development may mean that some information is not entirely up-to-date. The information in this document is subject to change without notice.

TomTom shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the performance or use of this material. This document contains information protected by copyright. No part of this document may be photocopied or reproduced in any form without prior written consent from TomTom N.V.

34. Copyright notices

© 2008 TomTom N.V., The Netherlands. TomTom®, and the "two hands" logo, among others, are Trademarks owned by TomTom N.V. or one of its subsidiaries. Please see www.tomtom.com/legal for warranties and end user licence agreements applying to this product.

Nuestra garantía limitada y nuestro acuerdo de licencia de usuario final para el software integrado son de aplicación para este producto; puede consultar ambos en www.tomtom.com/legal.

Data Source

Inc.

Loquendo is a registered trademark. www.loquendo.com

Some images are taken from NASA’s Earth Observatory.

The purpose of NASA’s Earth Observatory is to provide a freely-accessible publication on the Internet where the public can obtain new satellite imagery and scientific information about our home planet.

The focus is on Earth’s climate and environmental change: earthobservatory.nasa.gov/

Nuance® is a registered trademark of Nuance Communications, Inc. and is used here under license.

Reklama