DecaLED

®

Touch Panel DMX 4

95760822

Manual

CONTENT

Product Description ........................................................................1

Unpacking .....................................................................................1

Control Panel and Functions ........................................................... 2

Rear Panel View ............................................................................ 3

Operation Guide ........................................................................ 4~8

1. ON/OFF ................................................................................. 4

2. Built-in Program ..................................................................... 5

3. Brightness ..............................................................................5

4. Speed ....................................................................................5

Description

Thank you for purchasing our digital product DecaLED ® Touch Panel DMX 4. You now hold a premiere LED controller with DMX 512/PWM output. Its compact and portable design is convenient to mount and easy to operate for users.

Package contents

Physical Dimensions

1 x Manual

® Touch Panel DMX 4

Carefully unpack the carton. Check the contents to ensure that all parts are present and have been received in good condition. If any parts appear damaged or missing, notify the shipper immediately and retain packing

EU version

86

Safety Instruction

• Unplug mains before installing or wiring the fixture

• Never look directly into the light source

User must be qualified to be involved with installation and maintenance of this product.

User must follow the safety instructions and warning notes written in this manual.

Features

• Touch interface

• DMX 512/PWM output

DecaLED ® Touch Panel DMX 4 uses RGB three channels, 2A per channel, 6A in total.

Red is controlled by channel 1, 4, 7...

Green is controlled by channel 2, 5, 8...

Blue is controlled by channel 3, 6, 9...

US version

• Four function menus

• Assign 4 color settings to shortcuts

• Assign 4 selections of adjustable (speed and brightness) color loops

• Set fadetime for Power on/off and color exchange in the range of 0 to 4s www.decaled.com

• Select input voltage in DC12-24V according to the output loading voltage

• Function memory and power failure protect

Physical dimensions

Touch Panel DMX 4

5. Color ......................................................................................6

5.1 Recording Color ................................................................ 6

Color All rights reserved.

am

B rig 15.5mm

6.3 SCENE Record Lock/Unlock ...............................................7

7. Key Tone ................................................................................ 8

8. Default Setting ........................................................................8

Physical Dimensions ...................................................................... 9

Technical Specification .................................................................. 9

1 2 3

DecaLED Touch Panel DMX 4

- Product code: 95760822

4

Product Code:95760822

86mm design and this manual, may be made at any time without prior notice.

5.3 Setting Fadetime for Color Exchange .................................. 6

6. SCENE .................................................................................. 7

6.1 Recording SCENE ............................................................. 7

6.2 Playback SCENE ...............................................................7

Speed

Touch Panel DMX 4 User Instruction

Technical Specification

24-004-2869-00

Rev1.0

INSTRUCTIONS MANUAL

Please read this manual carefully and thoroughly before operating this unit.

Power Supply

Loading

Housing

DMX out

Power in & PWM out

Operation Temperature

Storage Temperature

Weight

Dimensions

DC 12-24V

2A per channel, 6A in total

Polycarbonate, white/black/gray

4-pin green terminal

6-pin green terminal

0 degC to +40 degC

-20 degC to + 70 degC

US 150g / EU 100g

EU 86(L) x86(W) x15.5(H)mm

US 76(L) x120(W) x15.5(H)mm

Touch Panel DMX 4 User Instruction Touch Panel DMX 4 User Instruction Page 9

Control and functions

Control Panel and Functions

Front Panel View

1

Operation Guide

2

3

4 am

Color

Speed

1 2 3

DecaLED Touch Panel DMX 4

- Product code: 95760822

B rig

4

Fig 1

7

6

5

6. SCENE

6.1 Recording SCENE

Up to 4 scenes can be recorded and played back in this mode. Each figure key corresponds to one scene. The procedure to record a scene is described below: a.

b.

c.

Touch "P" or "S" key to indicator lights up.

enable Auto Mode, the key clicks and the LED

Rotate the touch toggle to select the built-in program or adjust the speed.

Touch any of the figure keys to which you wish to record the scene, and hold on for more than 2 seconds.

d.

All indicators flash momentarily once to indicate the current parameters

(including the built-in program and the value of speed and brightness) have been recorded and saved into the key.

e.

Repeat step a~d to save more scenes to the other 3 figure keys.

8

Touch Panel DMX 4 (EU)

1. Power key

Used to power on/off DecaLED ® Touch Panel DMX 4.

2. Color key 1. Power key

Used to select color.

3. Program key

2. C key (color)

Used to select color.

Used to select Built-in program.

3. P key (program)

4. Speed key Used to select Built-in program.

Used to adjust speed.

Used to adjust speed.

5. Brightness key

Used to adjust brightness.

Used to adjust brightness.

6. Output Indicator

Used to display the current output.

7. Touch toggle

7. Touch toggle

Used to adjust color, brightness and speed, and select built-in programs.

6.2 Playback SCENE

Touch "P" or "S" key to enable Auto Mode. Then touch the corresponding button of 1~4 to raise the scene which has been stored in it. The LED indicator lights up and it starts to display the recorded scene.

6.3 SCENE Record Lock/Unlock

To lock scene record, touch "S" key and "P" key simultaneously and hold on for about 10 seconds. At this time, the "S" key is not valid. Besides, the figure keys1~4 can play back saved scenes only, but can not record scenes.

To unlock scene record, touch "P" key and "S" key and hold on for about 10 seconds until all keys flash once.

* NOTE:

Each figure key can have a color, or a scene , or both elements recorded.

8. Figure keys (1~4)

Used to record scene and color, as well as set fadetime.

Rear Panel View

The DecaLED ® Touch Panel DMX 4 features one group DMX OUT with 4-pin terminal connector and one group

POWER IN & PWM OUT with 6-pin terminal connector. Also a LINK IN and LINK OUT is available.

The configuration of the terminal is as the following:

1. LINK IN: 4-pin terminal (black)

2. DMX OUT: 4-pin terminal (orange)

3. PWM OUT & POWER IN: 6-pin terminal (green)

4. LINK OUT: 4-pin terminal (green)

Touch Panel DMX 4 User Instruction Page 7

1 2 3 4

Operation guide

1. ON/OFF

DecaLED ® Touch Panel DMX 4 can be connected to a DC power at any voltage from 12V to 24V. When the indicator of POWER button lights up, the unit powers on and resumes the output setting of last time.

In normal mode, to touch POWER key and hold on for 2s, DecaLED ® Touch Panel DMX 4 switches to the state of standby. At this time, the output is shut down. Touch the power key once again and hold on for 2s, the unit is powered on.

Setting Shortcut for Power ON/OFF

If this shortcut is not set, you will need to touch and hold the ON/OFF button for 2 seconds to turn the controller on or off. If the shortcut is set, the DecaLED ® Touch Panel DMX 4 will respond immediately with a single touch of the ON/OFF button.

• Touch “Program” key and “Power” key simultaneously and hold on for about 10 seconds until all keys flash momentarily once.

• Touch “Power” key once, DecaLED ® Touch Panel DMX 4 changes to standby condition. Directly touch any key on the panel, DecaLED ® Touch Panel DMX 4 starts up.

• To delete power shortcut, touch “Program” key and “Power” key simultaneously and hold on for about 10 seconds until all keys flash once.

Setting Fadetime for Power ON/OFF

• To set power on/off fadetime, follow the procedures below:

• Touch “Power” key and hold on for 5 seconds till all LED indicators flash once. Then release the Power key and the key flashes repeatedly.

• Touch any one of these keys--1, 2, 3, 4, Program, Color, Brightness or Speed.

• All indicators flash momentarily once to confirm the setting.

• The existing mode ends and changes to normal mode automatically.

Different keys represent different fadetime:

Keys

Fadetime

1

1s

2

2s

3

3s

4

4s

P/C/B/S

0s (no fade)

2. Built-in Program

Hold on pressing “Program” key for about 1s to enable built-in Program Menu, the key clicks and the indicator is lit. Then rotate the touch toggle to select a desired built-in program. There are 10 built-in programs plus an

Auto Program for user selection (“Auto Program” is the sequential running of these 10 built-in programs).

The process of selecting the built-in programs produces clicks and each click will activate one program.

3. Brightness

To enable Brightness Menu, hold on pressing “Brightness” key for about 1s, the key clicks and the indicator lights up. Then rotate the touch toggle to adjust the brightness as you wish. In clockwise, the brightness increases; In anti-clockwise, the brightness decreases.

NOTE: The value of brightness can be adjusted in the range of 0 to 255.

4. Speed

To enable Speed Menu, hold on pressing the “Speed” key for about 1s, the key clicks and the indicator lights up. Then rotate the touch toggle to adjust the speed of running built-in programs in the range of 0.2s~10min.

In clockwise, the speed will increase;In anti-clockwise, the speed will decrease.

When you rotate the toggle to reach 10min, the click disappears and all the four figure keys flash repeatedly.

Then you select the speed which you wish by pressing any of the figure keys. Different figure keys stand for different speed -- “1” for 10min, “2” for 20min, “3” for 30min and “4” for 40min.

NOTE: In the process of adjusting brightness and speed, the toggle produces clicks. However, the click disappears when the toggle reaches the maximum/minimum value.

5. Color

To enable Color Menu, hold on pressing the “Color” key for about 1s, the key clicks and the indicator lights up.

Then rotate the touch toggle to adjust the RGB value until you get the desired color.

5.1 Setting a color

Up to 4 colors can be configured and stored into the memory of the device in manual mode. Each figure key corresponds to one color. The procedure to assign a color is described below:

• Touch “Color” key to enable Manual Mode, the key clicks and the indicator is lit.

• Rotate the touch toggle to adjust RGB value until you get desired color.

• Touch any of the figure keys to which you wish to record the color, and hold on for more than 2 seconds.

• All indicators flash momentarily once to indicate the current parameters, including the value of color and brightness, have been saved into the key.

• Repeat these step to save a color to the other 3 figure keys.

5.2 Playback color

Touch “Color” key to enable Manual Mode. Then touch the corresponding button of 1~4 to select the color which you have assigned to the key. The LED indicator lights up and it starts to display the stored color.

5.3 Setting Fadetime for Color Exchange

To set the fadetime for color exchange, you take the following procedures:

• Touch “Color” key and hold on for 5 seconds till all LED indicators flash once. Then release the key and the

“Color” key flashes repeatedly.

• Touch any one of these keys--1, 2, 3, 4, Program, Color, Brightness or Speed.

• All indicators flash momentarily once to confirm the setting.

• The existing mode ends and changes to normal mode automatically.

Different keys represent different fadetime:

Keys

Fadetime

1

1s

2

2s

3

3s

4

4s

P/C/B/S

0s (no fade)

6. Scene

6.1 Customizing a scene

Up to 4 scenes can be recorded and played back in this mode. Each figure key corresponds to one scene.

The procedure to record a scene is described below:

• Touch “Program” or “Speed” key to enable Auto Mode, the key clicks and the LED indicator lights up.

• Rotate the touch toggle to select 1 of 10 built-in programs or adjust the speed.

• Touch any of the figure keys to which you wish to record the scene, and hold on for more than 2 seconds.

• All indicators flash momentarily once to indicate the current parameters (including the built-in program and the value of speed and brightness) have been recorded and saved into the key.

• Repeat these step to save more scenes to the other 3 figure keys.

6.2 Playback scene

Touch “Program” or “Speed” key to enable Auto Mode. Then touch the corresponding button of 1~4 to select the scene which has been assigned to it. The LED indicator lights up and it starts to display the recorded scene.

6.3 Scene record lock/unlock

To lock scene record, touch “Speed” key and “Program” key simultaneously and hold on for about 10 seconds.

At this time, the “Speed” key is not valid. Besides, the figure keys1~4 can play back saved scenes only, but can not record scenes.

To unlock scene record, touch “Program” key and “Speed” key and hold on for about 10 seconds until all keys flash once.

NOTE: Each figure key can have a color, or a scene, or both elements recorded.

7. Key tone

To turn on or turn off key tone, keep the four figure keys--”1”, “2” , “3” and “4” touched simultaneously until all keys flash momentarily once to confirm the setting, then release them.

With key tone ON, when you rotate the touch toggle to the maximum or minimum value, the key click disappears.

With key tone OFF, when you rotate the touch toggle to the maximum or minimum value, all keys flash repeatedly 3 times.

8. Default setting

Touch “Program” key and “Brightness” key simultaneously and hold on for about 10s until all keys flash once to resume default setting. All the settings by the user are deleted. The fadetime for color change and power

ON/OFF is 2 seconds, and the recorded scenes will be replaced by default setting.