Omron NT2000M, NT20M series Operation Manual
Advertisement
Advertisement
Cat. No. V001-E1-2
NT20M/NT2000M
Programmable Terminal
NT20M/NT2000M
Programmable Terminal
Operation Manual
Revised September 1993
iv
Notice:
OMRON products are manufactured for use according to proper procedures by a qualified operator and only for the purposes described in this manual.
The following conventions are used to indicate and classify warnings in this manual. Always heed the information provided with them.
DANGER!
Indicates information that, if not heeded, could result in loss of life or serious injury.
Caution Indicates information that, if not heeded, could result in minor injury or damage to the product.
Product References
All OMRON products are capitalized in this manual. The word “Unit” is also capitalized when it refers to an OMRON product, regardless of whether or not it appears in the proper name of the product.
The abbreviation “Ch,” which appears in some displays and on some OMRON products, often means
“word” and is abbreviated “Wd” in documentation in this sense.
The abbreviation “PC” means Programmable Controller and is not used as an abbreviation for anything else.
IBM and IBM PC/AT are registered trademarks of International Business Machines Corporation.
MS-DOS is a registered trademark of Microsoft Corporation.
Visual Aids
The following headings appear in the left column of the manual to help you locate different types of information.
Note
1, 2, 3...
Indicates information of particular interest for efficient and convenient operation of the product.
Indicates lists of one sort or another, such as procedures, precautions, etc.
OMRON, 1991
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form, or by any means, mechanical, electronic, photocopying, recording, or otherwise, without the prior written permission of OMRON.
No patent liability is assumed with respect to the use of the information contained herein. Moreover, because OMRON is constantly striving to improve its high-quality products, the information contained in this manual is subject to change without notice. Every precaution has been taken in the preparation of this manual. Nevertheless, OMRON assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained in this publication.
v
vi
TABLE OF CONTENTS
SECTION 1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1 Introduction
1-2 Features
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-3 NT-series Terminology
1-4 Models
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-5 Support Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-6 System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-7 Nomenclature and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 2
Settings and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1 Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2 Installation Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-3 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-4 Installing in a Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-5 Wiring and Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-6 RS-232C Interface Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-7 Mounting Function Key Units (to DN-type PTs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 3
Initial Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-1 Powering Up
3-2 Initialization
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-3 Transferring Data to and from the Support Tool
3-4 Initial Settings
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 4
Display Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1 Character Displays on Screen
4-2 Normal Screen Changes
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-3 Continuous Screens
4-4 Overlapping Screens
4-5 Numeric Displays
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-6 Character Strings
4-7 Bar Graphs
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-8 Lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-9 Graphics Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-10 Special Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 5
Input Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-1 On-screen Switch Inputs
5-2 Inputting Numeric Settings
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-3 Standalone Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 6
System Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-1 Configuration of System Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-2 System Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-3 Maintenance Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-4 Memory Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
29
30
30
32
33
45
46
47
50
51
52
53
53
60
13
14
16
17
18
21
26
27
35
40
41
41
42
42
36
36
37
38
39
1
6
6
8
3
4
2
2 vii
viii
SECTION 7
Online Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-1 Transferring Screen Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-2 Host to PT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-3 PT to Host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-4 Online Transmission and Resume Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 8
Maintenance and Inspection . . . . . . . . . . . . . . . . . . . . . . .
8-1 Checking Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-2 Changing the Lithium Backup Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-3 Replacing the Backlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-4 Maintenance and Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Appendices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A.
Standard Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B.
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
63
64
64
64
65
67
68
69
70
71
73
73
75
79
81
About this Manual:
Programmable Terminals (PTs) are terminals used mainly at FA production sites. The PT is connected to a host such as a Programmable Controller or an FA Computer, and is used to display the operating conditions of various devices and equipment. In addition, it can be used as a control panel with lamps and switches, or it can be used for inputting data. This manual describes the installation and operation of the
NT20M and NT2000M Programmable Terminals and includes the sections described below. Further information is provided on manuals on the Host Interface Units and Support Tool. Refer to the list in Section
1 Introduction.
Please read this manual completely and be sure you understand the information provide before attempting to install and operation a Programmable Terminal.
Section 1 introduces the PTs, describes the terminology used in this manual, and provides examples of system configurations for programming and operation.
Section 2 provides procedures and specifications required to set up a PT system, including hardware switch settings and installation.
Section 3 provides steps required for initial PT operation.
Section 4 describes functions used to create screens and control display attributes on the PT. Included is automatic transfer of data from the host computer via character string and numeral tables.
Section 5 describes functions used to input data on-screen and transfer it to the host computer via the numeral table.
Section 6 describes basic data transfer and maintenance functions.
Section 7 describes transferring screens online to and from the host computer.
Section 8 provides troubleshooting and basic maintenance methods, including battery replacement.
Appendices of OMRON products used with PTs and PT specifications are provided at the back of the manual.
ix
SECTION 1
Introduction
This section provides information necessary to familiarize you with the features and parts of a PT system.
1-1 Introduction
1-2 Features
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-3 NT-series Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-4 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-4-1 NT20M Programmable Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-4-2 NT2000M Programmable Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-4-3 12-key Function Key Units (for DN-type)
1-5 Support Tool
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-6 System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-7 Nomenclature and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-7-1 NT20M-D j
121-V2/D j
13 j
1-7-2 NT2000M-D j
131
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
8
8
10
6
6
4
5
3
4
2
2
1
Features Section 1-1
1-1 Introduction
This manual describes the installation and operation of NT20M and
NT2000M Programmable Terminals (PTs). Both models can come with or without touch panels. Programmable Terminals have three main functions: 1) monitoring operating conditions, 2) directing on-site personnel, and 3) inputting data.
1) PTs can monitor, in real time, system and equipment operating conditions, production quantities, and so on. The PT display can show, for example, whether the production line is operating normally, and what percentage of the production target has been met. Bar graphs can be continually updated as data is received from the host. On-screen characters can be displayed as plain, reverse video, blinking, or reverse blinking. In addition, lamps, bar graphs, and figures can all be created. Screen data can be registered at the
PT in advance, and can be displayed simply by transmitting the appropriate screen number from the host.
2) PTs can inform on-site personnel of current conditions that need to be addressed. Depending on the nature of the situation, built-in or external buzzers can be sounded to alert personnel to problems that have developed. Depending on factors such as distance from the host, the number of devices connected, and the response time, any of a variety of communications methods may be selected.
3) PTs can input data for controlling certain operations and communicating information to the host. Setting switches and a ten-key pad allows a PT to be used as a control panel. In the example shown below, touch switches used for inputs to the host are displayed. When this screen is displayed, the onsite operator can control a device by means of touch switches.
Aside from touch switches, the PT can provide inputs by means of numeric settings and externally connected switches. The illustration below shows a numeric setting screen that can be used for inputting numeric data.
The screens used for these operations can be created in advance by using the “Support Tool” software on a personal computer. The screen data that is created using the Support Tool can be printed out, saved to a diskette, or transferred to the PT. Either an FA Computer or a Programmable Controller can be used as the host.
1-2 Features
Clear Display
Industry’s Largest LCD
Screen
By increasing the dot size, the display screen for the NT2000M has been enlarged.
Industry’s First CFL
Two-color Backlight Display
With the NT20M-D j
131 and the NT2000M-D j
131 models, the backlight can be switched between white and red. It is ordinarily white, but under extreme circumstances it can be switched to red for greater visibility.
Display Functions
The display is extremely clear due to an STN liquid crystal display with a backlight. For long life, the backlight can be set to turn off automatically. With the NT20M-D j
131 and the NT2000M-D j
131 models, the backlight is replaceable.
Up to 250 screens can be registered. A total of 256 touch switches and rectangular or circular lamps can be created and registered, with up to 64 touch switches and/or lamps for a single screen. In addition, up to 32 messages
(strings of 32 characters) and 128 eight-digit numbers can be registered. Fig-
2
NT-series Terminology
Input Functions
Section 1-3
ures and bar graphs can also be created and displayed. Marks (16 dots x 16 dots) can also be created with the NT20M/NT600M Support Tool and displayed.
Up to 64 touch switch inputs can be registered per screen for Terminals with a touch panel (DT).
Drip-proof, Oil-proof Panel The NT20M PTs (except for those connected to the NT20M-FK210) have a drip-proof front panel structure when the dust cover is mounted to protect the display area and the key input area. For protection against oil spray, the front-panel sheets and moulded parts use oil-resistant materials. In addition, the NT2000M PTs have a completely water-proof structure when the panel is mounted.
Two-way Communications Messages and numbers transferred from the host can be displayed at programmed locations. In addition, numbers from touch panel and function key inputs can be transferred back to the host.
Host Interface
Communications
System Configuration
Five types of Host Interface Unit enable general RS-232C and RS-422 communications, special-purpose SYSMAC BUS (Wired) communications,
C200H Host Interface communications to the C200H, and Host Link direct connection communications.
NT-series Terminals have common communications protocol and peripheral devices. Select the Terminal you need based on screen size, memory capacity, and host interface.
Program Reusability
Stand-alone Capability
Programs for communicating with Programmable Controllers are upwardly compatible so the program can easily be reused when adding functions.
Screens can be changed on-site, without requiring instructions from the host.
At the time when the screens are created by the Support Tool in advance, screen-changing functions can be allocated to touch switches or function keys, thereby making it possible to easily change to any screen.
Online Transfer Capability When an RS-232C or RS-422 Interface Unit is mounted to the Host Interface
Unit, screen data can be changed by means of commands from the host.
Direct Connection Direct connection is a function whereby host data areas can be made to directly correspond to PT operations. Ordinarily, operating instructions to the
PT and inputs from the PT are carried out by means of command execution at the host. The direct connection function eliminates the need for such host commands and programming, thereby greatly reducing the size and complexity of the host program. Direct connection is possible for PTs with touch panels when a Host Link Interface Unit is mounted. In addition, the NT20M-
ZASAT-EV4 Support Tool and the NT20M-SMR31-E are required.
1-3 NT-series Terminology
The following are definitions for the names of items in this manual related to the NT Series of Programmable Terminal and SYSMAC C-series Programmable Controllers.
Abbreviations The following abbreviations are used in the text.
3
Models Section 1-4
Abbreviation
PT
PC
I/F
I/O
Term Meaning
Programmable Terminal Refers to an OMRON NT-series Programmable Terminal.
Programmable
Controller interface input/output
Refers to an OMRON SYSMAC C-series or CV-series Programmable
Controller, or programmable controllers manufactured by other companies.
A communications device that connects the Programmable Terminal with peripheral devices.
Refers to PT and PC inputs and outputs.
SYSMAC Terminology
Terminology
SYSMAC
Explanation
A generic name for OMRON’s Programmable Controllers.
Host Link System
SYSMAC BUS
C200H
A system employing SYSMAC C-series Host Link Units used to create a communications bus between PCs, between PCs and PTs, etc.
A remote I/O network created between SYSMAC C-series PCs and input/output devices.
An OMRON SYSMAC C-series Programmable Controller.
NT-series Manuals
Name of Manual
NT20M/NT2000M Operation
Manual
NT600M Operation Manual
NT-series Host Interface Unit
Operation Manual
NT20M/NT600M Support Tool
Operation Manual
NT-series Host Interface Unit
Direct Connection Operation
Manual
NT-series RS-232C/RS-422
Interface Unit Operation Manual
The NT20M/NT2000M Series and NT600M Series are covered in the four manuals described below.
Contents
This manual provides specifications, functions, and operating instructions for the NT20M and NT2000M Programmable Terminals.
This manual provides specifications, functions, and operating instructions for NT600M Programmable Terminals.
This manual covers the commands, controls, and communications specifications for operating the NT20M and the NT600M. Refer to this manual when programming host computer communications.
This manual covers methods for creating screens, including screen data preparation, switches, lights, and alarms.
This manual covers the Direct Connection feature which has been added to the Host Interface Unit.
Manual No.
V001
V002
V003
V004
V015
This manual covers the commands, controls, and communications specifications for operating the NT20M and the NT600M with the
RS-232C/RS-422 Interface Unit. Refer to this manual when programming host computer communications.
V016
1-4 Models
1-4-1 NT20M Programmable Terminals
The various NT20M PT models are shown in the table below. Several of these models employ two-color backlights. The two-color backlight incorporates red and white lights, one of which is selected according to operational requirements. The two-color backlights are replaceable, and are sold separately.
System ROM is sold separately for all models. Select the System ROM according to the Host Interface Unit that is mounted to the PT, as described in
Host Interface Units and Conforming System ROM on the following page.
NT20M type Model number
NT20M-DT121-V2
NT20M-DT131
( ) NT20M-DN121-V2
NT20M-DN131
Backlight
White
White or red
White
White or red
I/C socket: f th
Image data memory d l ith i d t separately, following the specifications in the
4
Models Section 1-4
1-4-2 NT2000M Programmable Terminals
The NT2000M-DT, touch-panel type and the NT2000M-DN131, non-touchpanel type models employ a two-color backlight (changeable between white and red), which is replaceable and is sold separately. The NT2000M-DN131, like the NT20M models described above, does not come with an image data memory chip mounted. This must be purchased separately.
System ROM is also sold separately. Select the System ROM according to the Host Interface Unit that is mounted to the PT, as described in Host Inter-
face Units and Conforming System ROM below.
Memory Chips In order for images to be saved, screen data memory is required. The following memory chips can be purchased separately and mounted in the socket.
Type
SRAM
Memory capacity
32K bytes
Model
RAM22-15
128K bytes RAM13-10
EPROM* 64K bytes ROM-KD-B
Recommended memory chips
HM62256ALP-15 (Hitachi).
HM628128LP-10 (Hitachi).
M5M27C512AK-12 (Mitsubishi)
128K bytes ROM13-12B HN27C101AG-12 (Hitachi).
EEPROM 32K bytes EER22-20 HN58C256P-20 (Hitachi).
Memory Capacity and
Number of Screens
Notes 1. When using EPROM, use a PROM writer to write the data that was created by the Support Tool, and then mount the chip in the PT.
2. If memory chips other than the recommended ones are used, the memory backup battery capacity may not be sufficient.
Screen memory capacity varies according to which Screen Data Memory
Board is installed. The screen memory capacity, in turn, determines the number of screens that can be registered. Use the table below as a guide to select the amount of memory suitable for your needs.
Screen memory capacity
32K bytes
64K bytes
Number of registered screens
Mostly messages: 140 screens
Mostly graphics: 50 screens
Mostly messages: 250 screens
Mostly graphics: 100 screens
128K bytes Mostly messages: 250 screens
Mostly graphics: 200 screens
Note The table above is strictly a guide. If the messages or other display data per screen increase, the number of screens that can be registered will decrease.
Likewise, if the messages decrease, the number of screens (250 screens max.) that can be registered will increase.
Host Interface Units and
Conforming System ROM
Host Interface Units provide the interface for communications between the
PT and the host, which may be either a C-series Programmable Controller or an FA computer. The System ROM is ROM which contains the programs necessary for operating the PT. Select the System ROM according to the
Host Interface Unit that is to be mounted to the PT. System ROM is used in common for both NT20M and NT2000M PTs.
Host Interface Unit
NT600M-LK201 (RS232C/SYSMAC WAY)
NT600M-LK202 ((RS-422)
NT600M-RT121 (SYSMAC BUS)
NT600M-LB121 (C200H Host Interface)
NT600M-LK201 (Host Link direct connection)
System ROM
NT20M-SMR01-E
NT20M-SMR02-E
NT20M-SMR31-E
5
System Configuration Section 1-6
1-4-3 12-key Function Key Units (for DN-type)
Function-key input for NT20M non-touch panel (DN) type models is made possible by attaching an NT20M-FK210 12-key Function Key Unit.
1-5 Support Tool
Screen data, memory table data, and system data are all created by the Support Tool. In order to fully utilize the functions of the NT20M and NT2000M
PTs, use a Support Tool version of NT20M-ZASAT-EV4 or higher. Screen data is interchangeable for NT20M and NT2000M PTs.
NT20M-ZASAT-EV j
Version
Overseas specifications (English)
Compatible platform
AT: IBM PC/AT compatible
Floppy disk size
3: 3.5 inch
5: 5.25 inch
S: 3.5 and 5 inch
Support software
NT20M-series, basic model
1-6 System Configuration
The Host Interface Unit mounted on the back of the PT is connected to the host (i.e., a personal computer or Programmable Controller) via communication cable. The PT must be used with a Host Interface Unit. If no Host Interface Unit is mounted, the PT will not operate. Refer to the NT-series Host
Interface Unit Operation Manual for details on connecting between the Host
Interface Unit and the host.
RS-232C Interface
(NT600M-LK201)
C200H, C500, C1000H, or C2000H PC
Using the N600M-LK201 Host Interface Unit, the Programmable Terminal can be connected one-to-one to a PC through an ASCII Unit, or to personal computer.
Personal computer
NT20M/NT2000M with NT600M-LK201
NT20M/NT2000M with NT600M-LK201
6
ASCII Unit
RS-232C
15 m max.
RS-232C
15 m max.
System Configuration
RS-422 Interface
(NT600M-LK202)
C-series PC
Section 1-6
Using NT600M-LK202 Host Interface Units, up to 16 NT20M or NT2000M
Programmable Terminals can be connected to a PC through an ASCII Unit, or to an FA computer.
FA computer
ASCII Unit
(RS-232C)
3G2A9-AL004-(P)E
Link Adapter
RS-422
Cable length: 500 m max.
NT20M or NT2000M with NT600M-LK202
3G2A9-AL001
Link Adapters
NT20M or NT2000M with NT600M-LK202
Branch lines: 10 m max. each.
(16 Terminals max.)
Host Link Unit Interface
(NT600M-LK201)
Using the NT600M-LK201 Host Interface Unit and RS-232C cable, the Programmable Terminal can be connected one-to-one to a PC through a Host
Link Unit.
C200H or C500 PC
NT20M or NT2000M with NT600M-LK201
Wired SYSMAC BUS
Interface
(NT600M-RT121)
C200H, C500, C1000H, or
C2000H PC
Host Link Unit
RS-232C
15 m max.
Using NT600M-RT121 Host Interface Units, up to 8 Programmable Terminals can be connected to a PC through a Wired Remote I/O Master Unit.
8 Terminals max.
NT20M or NT2000M with NT600M-RT121
Remote I/O
Master Unit
200 m max. (2-wire cable)
7
Nomenclature and Functions
C200H Host Interface
(NT600M-LB121)
Section 1-7
With the C200H Host Interface Units, the interface is set up simply by connecting with cable to the C200H CPU Rack or Expansion I/O Rack. It is also possible to connect to C20H, C28H, C40H, and C60H CPU Units or I/O
Units. Be sure to use a noise filter when connecting C jj H. Refer to the
Host Interface Units Operation Manual for details.
In a C200H PC System, you can ordinarily connect two Expansion I/O Racks to the CPU Rack. The C200H Host Interface Unit itself, however, functions as an
Expansion I/O Rack, and therefore when using a C200H Host Interface Unit, you can only connect one other Expansion I/O Rack.
C200H CPU Rack
C200H Expansion I/O Rack
NT20M or NT2000M with
NT600M-LB121
C200H-CN221
Connection Cable
1-7 Nomenclature and Functions
1-7-1 NT20M-D
j
121-V2/D
j
13
j
Front Panel
Display
POWER Indicator (green)
Lit while power is on.
RUN Indicator (green)
Lit during operation
BAT LOW Indicator (red)
Lights if the lithium battery voltage level drops.
Peripheral Device Interface
Drip-proof Cover
Drip-proof Cover Screw
To ensure drip-proof protection, tighten this screw securely.
Display
System Keys
Used when maintenance of the
NT20M, selecting the System
Menu, etc. Used during operation for scrolling the screen and inputting numeric values.
Note If there are is no battery installed, the BAT LOW indicator will light.
8
Nomenclature and Functions
Bottom
Section 1-7
Extended I/O Unit Connector
(NT20M-DN jjj only)
Remove seal when connecting a 12-key Function Key Unit.
Components under Drip-Proof Cover
NT20M-D j 121-V2
The illustration below is for the NT20M-D j 121-V2. The NT20M-D j 13 j is basically similar except for the contrast control being in a slightly different position.
Contrast Control
Adjusts display contrast.
Turning clockwise increases contrast.
Note When adjusting the contrast, use the screwdriver included with the drip-proof cover.
Reset Switch
Pressing this switch initializes the NT20M. The status of screen data before initialization is retained.
Peripheral Device Connector
Used to transfer screen data between the Support Tool and the NT20M.
Rear Panel
Lithium Battery Cover
The lithium battery is under this cover.
Cover for 8-position DIP switch for system settings
Slide switch for memory settings (SW2)
Socket with lever, for installing image data memory
Socket for mounting System ROM
(NT20M-SMR jj
)
Connector for Host Interface Unit
Terminal block cover
(Refer to 2-5 Wiring and Connectors)
9
Nomenclature and Functions
1-7-2 NT2000M-D
j
131
Front Panel
Section 1-7
Display
POWER Indicator (Green)
Normally lit when power is turned on.
RUN Indicator (Green)
Lit during operation.
BAT LOW Indicator (Red)
Lights when the voltage level of the lithium battery drops.
Rear Panel
System Keys
Note When no battery is installed, BAT LOW indicator operation is unstable.
Connector Cover
The RS-232C interface connector and the battery are located under this cover.
Backlight Cover
The backlight is located under this cover. To open the cover, push and slide upwards.
Host Interface Connector
Connects to the Host Interface Unit.
Slide Switch for Setting
Memory (SW2)
Switch Cover
Switches are located under this cover.
Terminal Block
Socket With Lever for Installing Screen
Data Memory
The image data memory chip is installed here.
Socket for Installing System ROM
The System ROM is installed here.
10
Nomenclature and Functions
Components Under the Connector Cover
Section 1-7
Peripheral Device
Interface Connector
Transfers image data between the
NT2000M and a peripheral device.
Buzzer Sound Enable/Disable Pin
When this pin is pulled out, the buzzer will not sound under any conditions. When the circuit is closed, the buzzer will sound in accordance with the system.
Lithium battery
Components Under the Switch Cover
System Key Unit
When using the System Key
Unit, remove the short-circuit socket.
8-pin DIP Switch for System Settings
Contrast Control
Adjusts display contrast. Sliding to the right increases contrast.
Reset Switch
Pressing this switch initializes the NT2000M. The status of screen data before initialization is retained.
External System Key Connector
This connector enables the system keys to be used externally.
11
SECTION 2
Settings and Installation
This section provides procedures to set hardware switches and install the PT.
2-1 Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1-1 System DIP Switch Settings (SW1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1-2 System ROM Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1-3 Memory Setting (SW2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1-4 Inserting the Screen Data Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2 Installation Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2-1 Installation Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2-2 Mounting Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-3 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-3-1 NT20M Programmable Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-3-2 NT2000M Programmable Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-4 Installing in a Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-5 Wiring and Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-5-1 Terminal Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-5-2 Power Supply and Battery Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-5-3 LG and GR Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-5-4 HOST RUN INPUT Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-5-5 ALM OUTPUT (Alarm Output)
2-6 RS-232C Interface Connector
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-7 Mounting Function Key Units (to DN-type PTs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18
18
21
16
16
17
17
14
14
15
15
15
16
25
26
27
21
22
23
24
13
Switch Settings Section 2-1
2-1 Switch Settings
There are switches to set under the switch cover on the back of the Terminal, and also on each Host Interface Unit. For Host Interface Unit switch settings, refer to the Host Interface Unit Operation Manual. Be sure to set the switches before installation if the installation location prevents access to the switches after installation.
2-1-1 System DIP Switch Settings (SW1)
The 8-pin DIP switch for system settings is located under the DIP switch cover on the back of the Terminal. Be sure that power is off when changing switch settings.
SW1
ON
1 2 3 4 5 6 7 8
Communications specification
(only for when NT600M-LK201 is mounted)
ON: Host Link
OFF: RS-232C
Not used.
Mode change enable/disable
ON: Enable
OFF: Disable
Not used.
Bit designation for lamps/touch switches
ON: 0 to 63
OFF: 0 to 111
Reserved (Always ON).
HOST RUN input enable/disable
ON: Disable
OFF: Enable
Automatic reset after communications error
ON: No automatic reset.
OFF: Automatic reset.
Automatic reset after communications error
HOST RUN input enable/disable
Bit designation for lamps and touch switches
Mode change enable/disable
Communications specification
Pin 3
“Automatic reset” means that, when an error occurs, no error message will be displayed and the next command will be executed when received. “No Automatic reset” means that, when an error occurs, an error message will be displayed and operation will stop.
If this pin is turned OFF then, when the HOST RUN INPUT turns OFF, Host Error will be displayed regardless of other conditions and processing will stop.
This pin designates the bits for lamp and touch switch display control for when Host Link
Interface Units, C200H Host Interface Units are used.
“Mode change” refers to changing between the System Menu and Transmit Mode,
Maintenance Mode, or RUN Mode. When an RS-232C or RS-422 Host Interface Unit is used, mode changes can be prohibited by means of a command from the host.
When an NT600M-LK201 Host Link Unit is used, the communications specification must be set to either Host Link or RS-232C. If the PC setting and the Host Interface Unit setting do not match, operation will not be possible.
Pin 3 is factory-set to OFF and must be turned ON by the user. Screens will not be displayed properly unless this pin is ON.
14
Switch Settings Section 2-1
2-1-2 System ROM Mounting
1, 2, 3...
1. Turn off the power to the PT.
2. Set the groove of the mounting screw on the right edge of the IC socket to O
(Open).
3. Mount the System ROM in the direction of the seal on the IC socket and set the groove of the mounting screw to C (Close) to lock the System ROM.
IC socket
Seal
Mounting screw
4. Make sure that the groove of the mounting screw is set to C, otherwise the
System ROM will not be locked.
Socket
The groove is improperly set
Note 1. Be sure to turn off the PT when mounting or dismounting the System
ROM to the IC socket, otherwise the internal memory of the PT may be damaged.
2. Be sure to lock the System ROM after mounting, otherwise the operation of the PT will be unstable.
3. OMRON Corporation has the copyright of the System ROM program.
Making a copy of the program is prohibited without the prior consent of the OMRON Corporation.
2-1-3 Memory Setting (SW2)
This switch is used to set the type of data memory to be installed in the socket at the back of the Terminal.
SW2
The switch is factory-set to the left, as shown here.
SW 2
Left
Right
Center
SRAM
Screen data memory
EPROM
EEPROM
Note 1. Be sure that the power is off when changing the setting.
2. Carefully check the switch settings and the memory chip before turning the power on. If memory is not installed in accordance with this switch setting, the Terminal will not operate properly and memory may be destroyed.
2-1-4 Inserting the Screen Data Memory
1, 2, 3...
1. Turn off the power to the PT.
2. Set switch 2 to match the memory chip that is to be inserted.
15
Installation Environment Section 2-2
3. Raise the IC socket lever, and insert the memory chip in the direction indicated on the seal. The chip will have either 28 or 32 pins. Line it up with the position shown on the seal.
4. Check to be sure that the memory chip is inserted securely, and then lock the lever back into place.
Note Be sure to turn the power off before removing the memory chip.
2-2 Installation Environment
The NT20M and NT2000M PTs have strong environmental resistance and high reliability, but you can maximize system reliability and make the most of their functions by observing the following considerations during installation.
2-2-1 Installation Site
Avoid installing the PT in a location where any of the following conditions exist.
• Ambient temperatures exceeding a range of 0 ° C to 45 ° C for the NT20M or
0 ° C to 50 ° C for the NT2000M.
• Abrupt temperature changes or condensation.
•
Relative humidity exceeding a range of 35% to 85%.
•
Corrosive or inflammable gasses.
•
Strong magnetism.
• Excessive dust, salt, or iron dust.
• Direct vibration or shock.
• Direct sunlight.
•
Spray from water, oil, or chemicals (even though the front panel of the
NT20M is drip-proof and the entire NT2000M is waterproof).
2-2-2 Mounting Position
The PT employs a liquid crystal display, so the angle of vision should be considered when mounting. Install the Terminal at a height and direction that make it easy for the operator to see.
Ambient Temperature The ambient operating temperature range is 0 ° C to 45 ° C for the NT20M and
0 ° C to 50 ° C for the NT2000M. Take the following factors into consideration.
•
Leave sufficient ventilation space.
• Do not install directly above machinery that radiates a lot of heat (e.g., heaters, transformers, high-capacity resistors).
• If the ambient temperature rises above 45 ° C, set up a fan or air conditioner.
Control panel
Fan
PT
Louver
Operation and Maintenance For safety during operation and maintenance, place the PT as far as possible from high-voltage machinery and power equipment.
16
Dimensions Section 2-3
Improving Noise Resistance Do not install the PT in a panel with high-voltage devices, and install it at least 200 mm from electric power lines.
Power line
200 mm min.
PT
200 mm min.
When installing the Terminal near devices with strong electrical or magnetic fields (such as solenoids), allow a distance of at least 40 mm, more if necessary.
Solenoid
PT
40 mm min.
Solenoid
40 mm min.
2-3 Dimensions
All dimensions are in millimeters.
2-3-1 NT20M Programmable Terminals
Terminals With and Without Touch Panels
208
220
110 98
4.5
82
40
Approx.
80
Cable
17
Installing in a Panel Section 2-4
Terminals With Function Keys
An NT20M-FK210 12-key Function Key Unit can be connected to PTs without touch panels (i.e., DN type PTs).
208
220
2-3-2 NT2000M Programmable Terminals
NT2000M-DN131
351
164
4.5
49
82
98
152
40
Approx.
80
Cable
232.5
218.5
365
12
76.8
Cable
2-4 Installing in a Panel
The NT20M is designed to be installed in a panel. Install it as follows:
1, 2, 3... 1.
Cut a hole in the panel in accordance with the recommended dimensions shown below. The panel should be between 1.6 and 4.8 mm thick.
For PTs that have the backlight replaced from the side (i.e., NT20M-DT/
18
Installing in a Panel Section 2-4
DN131), however, the panel should only be from 1.6 to 2.0 mm thick, in order to allow enough space to replace the backlight.
Side Space for Backlight Replacement:
When mounting the NT20M to a panel, leave open the space marked with dotted lines on the left of the rear panel as shown below.
175 mm min.
20 mm min.
NT2000M PTs have the backlight replaced from the back, so they need not be accessed from the side. All dimensions shown below are in millimeters.
NT20M-D j
121-V2
NT20M-D j 131
NT20M-DN121-V2 with NT20M-FK210
NT20M-DN131 with NT20M-FK210
Installation space
209 ± 0.5
NT2000M-DN131
+0.5 –0
Installation space
209 ± 0.5
Installation space
219
+0.5
–0
351
+0.5
–0
2.
Insert the Terminal into the hole from the front of the panel.
NT20M NT2000M
19
Installing in a Panel Section 2-4
3.
Use the accessory metal fittings and tool to fasten the Terminal to the panel surface. Do not use a screwdriver on the fittings, otherwise the fittings or the terminal of the NT20M may become damaged.
NT20M NT2000M
Securing the NT20M to the Panel
After setting the NT20M into the panel, secure it as shown below.
(1) Fitting
Plastic
NT20M
(2)
(1) First pass the plastic part of the fitting through slot (a).
(2) Next, put the hook of the fitting into slot (b) and pull so that the leg catches in the NT20M case.
(a)
(b)
Turn the screw with the tool that comes with the NT20M, and secure the
NT20M to the panel. When you are finished, rotate the tool in the reverse direction and remove it from the screw.
Accessory tool
NT20M
4.
To remove the NT20M from the panel, use a flat-blade screwdriver. (For the NT2000M, use a Phillips screwdriver.)
4 panel installation fittings
Flat-blade screwdriver
Securing the NT2000M to the Panel
Using the tool that comes with the NT2000M, secure the NT2000M to the panel from behind. When not making it waterproof, the four places marked
“A” in the illustration below must not be tightened. Use a tightening torque of no more than 6 kg.
When making the NT2000M waterproof, tighten all twelve places shown in the illustration, including the places marked “A.” Use a tightening torque of at least 8 kg and no more than 10 kg.
20
Wiring and Connectors Section 2-5
To remove the NT2000M from the panel, use a Phillips screwdriver.
View from rear
A
É
É
É
Phillips screwdriver
A A
A
2-5 Wiring and Connectors
2-5-1 Terminal Block
The terminal blocks illustrated below are located under the respective terminal block covers of the NT20M and the NT2000M.
NT20M
ALM
OUTPUT
HOST
RUN
INPUT
24 VDC
+
10 Terminal screws: M3.5
1.4
3 10
Dimensions are in millimeters.
NT2000M
HOST
RUN
INPUT
ALARM
OUTPUT
Terminal screws: M4
100 to 240 VAC
50/60 Hz
LG GR
Crimp-style Terminals for Wiring
Use crimp-style terminals for wiring. If twisted wires are connected directly, there is a possibility of poor contact or short-circuiting. For the NT20M, use crimp-style terminals with holes to match M3.5 screws. For the NT2000M, use crimp-style terminals with holes to match M4 screws. The dimensions shown in the illustration below are for the NT20M. For the NT2000M, the dimensions would be 8.6 mm max. for both the fork-type and the round-type.
Fork-type Round-type
7 mm max.
8 mm max.
21
Wiring and Connectors Section 2-5
Conforming Crimp-style Terminals
Maker
Japan Solderless Terminal MFG
Fuji Terminals
Fork-type
(NT20M)
2-YS3A
2-YAS3.5
Nichifu Terminals 2Y-3.5
Round-type
(NT20M)
2-3.5
V2-S3.5
2-3.5
Fork-type
(NT2000M)
2-4A
2-YA4
2Y-4
Round-type
(NT2000M)
2-4
V2-4
2-4
Conforming wire (twisted)
1.04 to 2.63 mm 2
2-5-2 Power Supply and Battery Wiring
24 VDC (NT20M)
These are the power supply input terminals for running the NT20M.
+
Breaker
24-VDC power supply
NT20M Power Supply Wiring
•
Provide 24-VDC power.
• Use a power supply within the allowable voltage range.
Power supply voltage
24 VDC
Allowable voltage range
20.4 to 26.4 VDC
• Use a power supply with a rated capacity of at least 15 W at 24 VDC.
•
If power lines are long, then use wires of at least 2 mm 2 to avoid a drop in voltage.
•
Use twisted-pair cables.
• Turn off the power before wiring.
•
Be careful not to reverse the positive and negative terminals.
• Do not run the wiring between the 24-VDC power supply and the PT power supply input terminal parallel to or in close proximity with high-voltage or high-current power lines.
•
If you anticipate noise levels exceeding specifications, use noise-prevention measures such as installing a noise filter at the power supply. Use a common mode filter as the noise filter, and install no more than 100 mm of wiring from the PT to the filter.
• If you use a 24-VDC power supply with no output short-circuit prevention, then wire a breaker into the circuit.
22
Wiring and Connectors
AC Input (NT2000M)
Section 2-5
These are the power supply input terminals for running the NT2000M.
100 to 240 VAC
50/60 Hz
MCCB
Insulated transformer
NT2000M Power Supply Wiring
• Provide a 100 to 240 VAC power.
•
Use a power supply within the allowable voltage range.
Power supply voltage
100 to 240 VAC
Allowable voltage range
85 to 264 VAC
•
Insulated Transformer
The NT2000M has built-in anti-noise features which are sufficient for handling general noise from power lines, but ground noise can be greatly reduced by supplying power through a 1:1 insulated transformer. The secondary side of the insulated transformer should be an isolated neutral system.
• Power Capacity
Use a rated power supply of at least 50 VA.
• If power lines are long, then use wires of at least 2 mm 2 to avoid a drop in voltage.
• Use twisted-pair cables.
2-5-3 LG and GR Terminals
HOST
RUN
INPUT
ALARM
OUTPUT
100 to 240 VAC
50/60 Hz
LG GR Terminal screws are M4.
• GR is the ground terminal. In order to avoid electric shock, use separate ground wire (at least 2 mm 2 ) and a class-3 ground (ground resistance
100
W
or less).
•
LG is the noise filter neutral terminal. If malfunction results from excessive noise, or to prevent electrical shock, short-circuit LG and GR and use a class-3 dedicated ground.
•
The ground line should be 20 m or less.
23
Wiring and Connectors Section 2-5
•
Sharing a ground line with other machinery or grounding to the girders of a building may be ineffective and even harmful.
NT2000M
LG GR
Other machinery
NT2000M
LG GR
Other machinery
Okay
Class-3 ground
No
2-5-4 HOST RUN INPUT Terminal
Use the HOST RUN INPUT when you want to monitor the RUN status of the host. When this input terminal is enabled by pin 2 of DIP switch 1, then, if the
HOST RUN INPUT turns OFF, PT processing will be interrupted and a priority message will be displayed indicating that a host error has occurred. This condition will be maintained until the host RUN status is restored.
Enable: Turn OFF SW1, pin 2.
Disable: Turn ON SW1, pin 2.
NT20M
NT20M
24 VDC
Host
Host RUN status with transistor ON.
620
Ω
5.6 k Ω
HOST RUN
INPUT
1000 pF
NT2000M
Host
Host RUN status with transistor ON.
HOST
RUN
INPUT
620
Ω
5.6 k
Ω
1,000 PF
(This terminal has no polarity.)
24
Wiring and Connectors
Input Specifications (For Both NT20M and NT2000M)
Item
Rated input voltage
Input impedance
Input current
ON voltage
OFF voltage
ON delay
OFF delay
Insulation method
Content
24 VDC +10% /
–15%
5.6 k Ω
4.1 mA typical (at 24 VDC)
15.5 V min.
5.0 V max.
2.5 ms max.
2.5 ms max.
Photocoupler
Section 2-5
2-5-5 ALM OUTPUT (Alarm Output)
This terminal outputs the PT alarm signal. Use this terminal when you want to externally monitor status.
NT20M
24 VDC
External device
Load
ALM
OUTPUT
Item
Output type
Rated load
Maximum load current
Minimum switching capacity
Leakage current
Residual current
ON delay
OFF delay
Relay output
24 VDC
+10%
/
–15%
1 A
10 mA at 5 VDC
0.1 mA max.
1.0 V max.
2.5 ms max.
2.5 ms max.
Content
25
RS-232C Interface Connector
NT2000M
External device
Load
ALM output
100 to 240 VAC input
Section 2-6
Item
Output type
Rated load
Relay output
1 A at 24 VDC
Maximum load current 1 A
Minimum switching capacity 10 mA at 5 VDC
Content
2-6 RS-232C Interface Connector
The RS-232C interface connector is used during communications between the PT and the Support Tool. It is located under the RS-232C interface connector cover on the front of the NT20M or NT2000M.
Pin Allocation
1
2
3
4
5
9
Pin no.
FG
SD
RD
RS
CS
SG
Symbol Name
Frame Ground (not used)
Send Data
Receive Data
Request to Send
Clear to Send
Signal Ground
Connection Diagram
Personal computer
(25 pins)
2
SD
3
RD
4
RS
5
CS
7
SG
1
FG
RS-232C
4
5
9
1
2
3
PT
SD
RD
RS
CS
SG
FG (Not connected.)
Shielded wire
D-sub connector, 9 pins
Note 1. RS-232C communications conditions are set automatically by the NT20M
Support Tool.
2. Connectors can be connected and disconnected with power turned on.
3. This connection diagram cannot be used for the Host Interface Unit.
26
Mounting Function Key Units (to DN-type PTs) Section 2-7
Applicable Connectors
(Cable Side)
Plug: XM2A-0901 (OMRON) or equivalent.
Hood: XM2S-0911 (OMRON) or equivalent.
Recommended Cables
Cable Set
AWG 28 x 5P IFVV-SB (Fujikura Cable, Ltd.)
CO-MA-VV-SB 5P x 28 AWG (Hitachi Cable, Ltd.)
CV500-CN228 (OMRON)
Cable length: 2 m
2-7 Mounting Function Key Units (to DN-type PTs)
Mounting Procedure
1, 2, 3...
1. Remove the rubber packing and bottom connector seal from the DN-type
PT.
2. Mount the 12-key Function Key Unit to the PT, matching the connectors. Using a Phillips screwdriver, tighten the five mounting screws.
NT20M-DN jjj
Programmable Terminal
Phillips screwdriver
NT20M-FK210 12-key
Function Key Unit
Mounting screws (5 places)
3. Attach the rubber packing that comes with the 12-key Function Key Unit.
Rubber packing
4. Mount to the panel.
27
SECTION 3
Initial Operation
This section provides an introduction to the operations necessary to use a PT for the first time and to the menus and keys used to control PT operation.
3-1 Powering Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-2 Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-2-1 Initializing Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-2-2 Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-3 Transferring Data to and from the Support Tool
3-4 Initial Settings
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
30
30
30
31
32
33
29
Initialization Section 3-1
3-1 Powering Up
When first starting up the system, do not connect the Host Interface Unit to the host. When power is turned on to the PT, either a “Connecting to host” message or the initial screen set by the Support Tool will be displayed. The
“Connecting to host” message will be displayed if a Host Link Interface Unit, a SYSMAC BUS Interface Unit, or a C200H Host Interface Unit is mounted.
The initial screen will be displayed if an RS-232C/RS-422 Interface Unit is mounted.
If there is no image data registered for the PT, or if there is an error in the image data that is registered, then the System Menu will be displayed instead, with an error message at the bottom. In that case, it will be necessary to initialize the memory and transmit the correct data.
3-2 Initialization
Initialize the memory in the PT using the procedure described below. This procedure can also be used later to completely delete data from the PT. Always be careful not to initialize and delete essential data.
3-2-1 Initializing Memory
Perform the initialization if the screen memory is either SRAM or EEPROM.
Check to be sure that the screen memory is installed.
Memory initialization can be used to initialize screen memory, memory tables, and history data. Initializing screen memory completely deletes the contents of the screen memory, including the contents of numeral tables and text string memory tables. Initializing memory tables overwrites numeral tables and text string memory tables with the initial values set by the Support Tool.
Initializing the display history deletes all of the display history data.
To initialize the screen memory, first access the system menu by simultaneously pressing the Buzzer Key, Up Key, and Down Key. Then proceed as shown below.
System Menu
Select “MAINTENANCE MODE.” Refer to Section 6 System Menu.
Select “Init. Screen.”
Initialize Screen Memory?
Yes
No
If you select yes, then memory will be initialized and all data used for displays will be erased. After initialization, operation will begin.
30
Initialization
3-2-2 Menus
Section 3-1
If you select no, then operation will begin without initialization.
When entering RUN Mode after initialization, nothing will be displayed on the screen and the Terminal will wait for a command from the host.
Caution Screen memory must be initialized before using a new PT. If the PT is used as shipped from the factory without initialization, messages indicating errors in the host will not be displayed properly.
The System Menu is called up by using the system keys during operation.
SYSTEM MENU
Quit
Transmit Mode
Maintenance Mode
Using System Keys
Operation
Press the Buzzer Key, Up Key, and Down Key simultaneously.
Press the Up Key.
Press the Down Key.
Press the Enter Key.
Content
The System Menu shown above is displayed during operation. If actions are executed while the System Menu is being displayed, the system returns to operation. With the
Buzzer Key pushed down, press the Up Key and Down Key simultaneously.
Moves the bar cursor upward.
Moves the bar cursor downward.
Selects the menu at the position of the bar cursor.
Quit Use either of the following two methods to leave the System Menu and return to operation.
1, 2, 3... 1.
Select “Quit.”
OR
2.
Press the Buzzer Key, Up Key, and Down Key simultaneously.
In addition, if there are no key inputs within 10 s of calling up the System
Menu, the system will automatically return to normal operation.
Selecting Items To select an item, move the cursor to that item and press the Enter Key.
Selected item
Quit
Transmit Mode
Function
Quits and return to normal operation.
Shifts to Transmit Mode.
Select when transferring data between the PT and Support Tool. For details, refer to 3-3
Transferring Data to and from the Support Tool.
Maintenance Mode Shifts to Maintenance Mode.
Used to check the setting status of the PT and conducts self-testing.
31
Transferring Data to and from the Support Tool
Error Messages
Section 3-3
When there is an error in screen data registered in the PT, the System Menu will appear before entering RUN Mode, and the error message will be displayed on the bottom line.
System Menu
Quit
Transmit Mode
Maintenance Mode
Screen Data Corrupted - - - - - - - - - - - - - - Example of error message
Error message
Screen Data Corrupted
Mark Data Corrupted
Memory Not Formatted
There are three types of error messages, as shown below. Operation will not begin again until the error has been corrected.
Error Content and Correction
This is displayed when registered screen data is corrupted. Initialize the screen data and re-register the screen data. Operation will not begin again until the data is restored.
This is displayed when registered mark data is corrupted. Initialize the screen data and transfer the screen data files. The mark data is included in the screen data files. Re-register the mark data. Operation will not begin again until the data is restored.
This is displayed when the screen data area is not formatted. Initialize the screen data memory. All registered screen data, mark data, and system data will be deleted by the initialization, so they will have to be transferred again from the Support Tool. In addition, if the image data memory is the IC socket type, recheck the socket memory and its settings.
3-3 Transferring Data to and from the Support Tool
The following data can be transferred between the PT and the Support Tool.
Data
Screen data
Text string table
Numeral table
Mark data
Display history data
System Memory* (Initial screen after power-up)
Support Tool to PT PT to Support Tool
All screens or one screen All screens or one screen
YES YES
YES
YES
None
YES
YES
YES
YES
YES
Note System Memory is the first (initial) screen after the PT is powered up.
Procedure Use the following procedure to transfer data.
1, 2, 3... 1.
Connect the PT and personal computer running the Support Tool.
2.
Select Transmit Mode from the System Menu.
System Menu
Refer to Section 6 System Menu.
Select “Transmit Mode.”
32
Initial Settings Section 3-4
3.
Perform the transfer operation from the Support Tool. The screen shown below will be displayed during the transfer.
Transmit Mode
PT --> Host
Host --> PT
Shows direction of data transfer.
KB
Screen Data
System Memory
Memory Tables
Mark Data
History Data
Shows type of data.
Abort:
Number of bytes transferred (in kilobytes).
Press these three System Keys simultaneously to stop the transfer in progress.
4.
In the event of a disconnected cable or other disruption while the transfer is in progress, the PT screen will go blank and a message telling you that transfer was not possible will be displayed at the Support Tool. If the transfer is completed successfully, then at the end of the transfer the PT screen will go blank and a message telling you that the transfer has been completed will be displayed at the Support Tool.
5.
To return from Transmit Mode to RUN Mode, press the Buzzer Key, Up
Key, and Down Key simultaneously.
Note After completion of the transfer, be sure to change to Maintenance Mode. If power is turned off or the reset switch is pressed before changing to Maintenance Mode, the data that is transferred will be damaged.
When using the EEPROM as a screen data memory, screens cannot be transferred screen by screen from the Support Tool to the PT. The screen data must be transferred in file units after initializing the memory.
3-4 Initial Settings
When power is turned on, the PT’s internal status is initialized to the following settings.
Item
Character string memory
Numeral memory
Lamp/touch switch status
Key Press Sound
Backlight Off
Display
Initial value
Screen data memory content
Screen data memory content
OFF
ON (When a battery is installed, the previously set value is retained.)
10 minutes (When battery is installed, the previously set value is retained.)
No display or initial screen (At the Support Tool you can set either no display or initial screen.)
33
SECTION 4
Display Functions
This section describes the functions used to create screens and control display attributes on the PT. Functions used to input data on-screen are described in Section 5 Input Functions. Data transfer and maintenance functions are described in
Section 6 System Menu. Transferring screens online to and from the host computer is described in Section 7 Online
Transfer.
4-1 Character Displays on Screen
4-1-1 Types of Characters
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1-2 Designating Display Positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1-3 Character Scale
4-1-4 Display Attributes
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-2 Normal Screen Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-2-1 Procedure for Changing Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-3 Continuous Screens
4-4 Overlapping Screens
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-5 Numeric Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-6 Character Strings
4-7 Bar Graphs
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-8 Lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-9 Graphics Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-10 Special Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-10-1 Backlight On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-10-2 Backlight Red/White . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-10-3 Buzzer On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-10-4 Alarm Output On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-10-5 HOST RUN INPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-10-6 Display History Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-10-7 Terminal Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
40
41
41
42
37
38
39
36
36
36
37
36
36
36
43
43
43
43
42
42
43
44
35
Normal Screen Changes Section 4-2
4-1 Character Displays on Screen
The type, size, and attributes of characters that can be displayed on the
NT20M and NT2000M screens are shown below. Character type, size, and attributes are set at the time of creation on the Support Tool. When an
RS-232C or RS-422 Host Interface Unit is used, coordinates, characters, etc., can be designated with commands from the host in Terminal Mode.
4-1-1 Types of Characters
Half-size characters (8 x 8 dots)
Normal-size characters (8 X 16 dots)
Marks (16 X 16 dots)
Alphanumeric characters and symbols.
Alphanumeric characters and symbols.
Pictographs defined by the user (up to 64 possible).
4-1-2 Designating Display Positions
The display positions can be designated in increments of display dots. When characters overlap, characters written last overwrite those written earlier.
4-1-3 Character Scale
It is possible to designate normal, double-width, double-height, 4x, 9x, or 16x character size. When enlarging by 4x or more, the Programmable Terminal’s automatic smoothing process (a process that removes the notches from characters when they are enlarged) makes the characters easier to read.
4-1-4 Display Attributes
Besides the standard display (black characters on a white background), you can designate individual characters as inverse, blinking, or inverse/blinking.
Blinking jj Inverse blinking
Note You cannot designate the blinking cycle.
16x characters
4x characters
Wide characters
Normal-size characters
4x characters
Wide characters
4-2 Normal Screen Changes
The displayed screen can be changed to another screen by designating the screen number from the host (a Programmable Controller or personal com-
36
Continuous Screens Section 4-3
puter). The designated screen must have already been created at the Support Tool and downloaded to the PT.
4-2-1 Procedure for Changing Screens
1, 2, 3... 1.
By designating a screen number (0 to 250) from the host, you can switch to the designated screen.
2.
When an ordinary screen is displayed, the screens cannot be changed by means of the Up and Down Keys on the front panel of the NT20M.
3.
For details on screen-changing procedures for each interface, refer to the Host Interface Unit Operation Manual.
Note Screen no. 0 is white with no characters.
4-3 Continuous Screens
Screens can be linked to display consecutively, without breaks. A maximum of eight screens can be made consecutive, and treated as one screen.
Example Parent screen for consecutive screens
Screen no. 09
20
→
21
→
23
Screen no. 9: Screens displayed
20
A
Register the screen numbers of the child screens that you want to make consecutive. (You can set screen numbers in any order you want.)
Screen contents
21
B
23
D Screen
20
21
22
23
A
B
C
D
1, 2, 3... 1.
If screen 09 is designated from the host, screen 20 is displayed first.
2.
Screens B and D will be displayed in order, either by line or screen scroll when the Down Key is pressed, depending on the scroll unit setting.
• With line scroll, pressing the Down or Up Key will scroll eight dots at a time.
• With screen scroll, one screen will be scrolled at a time.
• Line and screen scroll are designated by the Support Tool when registering continuous screens. Screens with variable character string displays, numeric displays, graph displays, touch switches, lamps, or numeric settings cannot be scrolled by line.
37
Overlapping Screens Section 4-4
•
Screens with numeric settings cannot be designated as a child screen for any consecutive screen.
•
A continuous screen cannot be registered as a child screen.
Note The parent screens (screen no. 09 in this case) cannot have screen data.
They can be treated only as parent screens.
4-4 Overlapping Screens
The contents of multiple screens can be laid one on top of another and registered as one screen, when the screens are created on the Support Tool. Just as with ordinary screens, if the number of a screen registered as an overlapping screen is designated from the host, then the overlapping screens corresponding to that number are displayed.
•
A maximum of eight screens may be overlapped.
• Screens with touch switches, lamps, graphs, character strings, and numeric displays can be overlapped.
•
An overlapping screens cannot be registered as a child screen.
Example If screen 02 is designated from the host, then screens 03, 05, and 08 are displayed.
Parent screen: Screen no. 02
Overlapping screens
Numbers of child screens:
03
05
08
Screen no. 02 is designated by the host.
Screen no. 02: Screen displayed
My name is Smith.
Contents of child screens registered to overlapping screen no. 02:
Screen no. 03
My name
Note The contents of the screens are not displayed during setting operations.
Screen no. 05 is
Screen no. 08
Smith.
Note The parent screens (screen 02 in this case) cannot have screen data. They can be treated only as parent screens.
38
Numeric Displays Section 4-5
4-5 Numeric Displays
A numeral table is stored in the PT, and you can display numeric values from the table at programmed positions on a screen. In addition, the values in the table can be transferred from the host so that they are renewed each time a new value is transferred. The display positions are set in advance with the
Support Tool.
Example
Weld
Paint
Assem
Final
Screen Registered
Production
Line 1
# 1
Line 2
# 5
# 2 # 6
# 3
# 4
# 7
# 8
Contents registered to screens by Support Tool:
Numeral table numbers
Display positions
Number of digits displayed (whole numbers, fractions)
Sizes of characters displayed
No.
# 1
# 2
# 3
# 4
# 5
# 6
# 7
# 8
Numeral Table
(Maximum of 128 entries)
Contents
1020
832
711
630
556
999
807
777
Weld
Paint
Assem
Final
Screen Displayed
Production
Line 1
1020
832
Line 2
556
999
711
630
807
777
These contents are transmitted from the host.
When the PC is used as the host, for example, these values will be transferred via the Host
Interface Unit and updated on screen when the contents of the DM Area are changed.
39
Character Strings
4-6 Character Strings
This function displays variable character strings on the screen. These character strings can be changed with transmissions from the host. A character string memory table is stored in the PT. By changing, from the host, the memory table values corresponding to the display position, you can update the characters displayed. The designation of the display positions is set in advance at the Support Tool.
Example
Section 4-6
Weld
Paint
Assem
Final
Screen Registered
Production
Line 1
# 1
Line 2
# 5
# 2
# 3
# 4
# 6
# 7
# 8
Contents registered to screens by Support Tool:
Character string memory table numbers
Display positions
Number of characters displayed
Sizes of characters displayed
No.
# 5
# 6
# 7
# 8
# 1
# 2
# 3
# 4
Character String Table
(Maximum of 32 entries)
Contents
Van
Car A
Car B
High-roof
Sports A
Convert
Screen Displayed
Weld
Paint
Production
Line 1
Van
Line 2
Sports A
Car A Convert
Assem Car B
Final High-roof
40
These contents are transmitted from the host.
When the PC is used as the host, for example, these values will be transferred via the Host
Interface Unit and updated on screen when the contents of the DM Area are changed.
Lamps Section 4-8
4-7 Bar Graphs
If the numeric values that you want to make into a bar graph have been input into the numeral table in advance, then that graph can be displayed simply by designating the screen on which the graph is registered. Just as with numeric displays, the graph display is also updated when the contents of the numeral table are updated. Bar graphs can be displayed either horizontally or vertically.
Example
Goals
Graph Display
Goals
Line 1 # 0 Line 1 50%
Line 2
Line 3
75%
100%
Line 2 # 1
Line 3 # 2
Contents registered to screens by Support Tool:
Display positions (50 bars max.)
Graph width (2 to 255 dots)
Graph orientation (horizontal and vertical)
Display direction (normal or inverted direction)
100% value
With or without % numeric display
Position of % numeric display
% numeric font
Enlarged % numeric display
Numeral table numbers to be referred to
With or without +/– symbol
With or without graph frames
# 0
# 1
# 2
Numeral Table
(Maximum of 128 entries)
No.
Contents
1020
832
711
4-8 Lamps
With the Support Tool you can set lamp areas in the display screen, and the lamps can be made to light (or blink) by means of a designation from the host. Lamps are registered in advance at the Support Tool.
Display position: Can be set as desired, but must match the switch frames when combining lamps with the switch function.
Shape: Square and circle.
Size: The size of the square or circle can be freely set.
41
Special Controls
Example 1: Usage with
Switch Frames
Section 4-10
Number of settings: The total number of lamps must not be greater than
64 per screen.
Display attribute: Lit or flashing (used for bit designation).
Guide characters: With or without (selectable).
Lamps set from the host can be turned on and off by either of two methods: number designation or bit designation. For details, refer to the Host Interface
Unit Operation Manual.
If using a lamp together with a switch, then set the lamp within the switch frames, of which there are 12 horizontal and 6 vertical.
Example 2: Emphasis The display of the number defective can be emphasized setting it to blink.
Goal
Complete
Defective
1234
600
2
4-9 Graphics Display
Unbroken straight lines (polylines) and circles can be created by the Support
Tool and displayed at the PT. When an RS-232C or RS-422 Interface Unit is used, the graphics can be displayed by using the terminal function and transmitting commands from the host. (The terminal function can be used with all versions. See 4-10-7 Terminal Function.)
Designating Display
Positions
Graphics display positions can be designated in dot units. In cases where graphics and characters overlap, the graphics will be overwritten. Polylines and circles are both drawn with a width of one dot.
4-10 Special Controls
The status of the PT can be controlled from the host during operation.
4-10-1 Backlight On/Off
In order to prolong the life of the backlight, the backlight can be set to turn off when it is not needed during operation.
42
Special Controls Section 4-10
Note If there is any key input or screen-change command while the backlight is off, the backlight will turn on again.
4-10-2 Backlight Red/White
The backlight can be changed from white to red during operation. This is possible for the following models: NT20M-DT13 j /DN131 and
NT2000M-D j 131.
4-10-3 Buzzer On/Off
The built-in buzzer can be turned on and off from the host. There are two types of buzzers, continuous and intermittent. The buzzer also sounds when a screen registered with the buzzer is displayed. The buzzer stops when the
Buzzer Key is pressed. The NT2000M allows for the buzzer to be disabled when the setting pin is disabled.
4-10-4 Alarm Output On/Off
The ALM OUTPUT can be turned ON and OFF from the host. The ALM
OUTPUT terminal ON/OFF is also output when a screen registered for an alarm is displayed, or when an error occurs. This terminal can be used for large lamps or sound devices.
NT2000M NT20M
ALM
OUTPUT
24 VDC
+
ALARM
OUTPUT
(COM)
4-10-5 HOST RUN INPUT
The HOST RUN INPUT detects when the host in not in RUN, and displays the host error screen. Pin 2 of SW1 is used to enable and disable this input.
Pin 2 of SW1 ON:
Pin 2 of SW1 OFF:
NT20M
HOST RUN INPUT disable.
HOST RUN INPUT enable.
NT2000M
24 VDC
HOST
RUN
INPUT
+ HOST
RUN
INPUT
(COM)
4-10-6 Display History Clear
History data in the PT can be cleared (initialized) by the host. Until this operation is executed, history data continues to be registered.
43
Special Controls Section 4-10
4-10-7 Terminal Function
This function allows you the option of displaying, by transmission on command, the codes (coordinates, type, etc.) of characters and figures you want to display from the host, in addition to screens registered in advance. This function is possible only when the Host Interface Unit is the NT600M-LK201
(RS-232C specifications) or the NT600M-LK202 (RS-422 specifications). For details, refer to the terminal commands listed in the Host Interface Unit Oper-
ation Manual.
Item
Display position Optional
Content
Character size
Display attributes
Normal, half-size, high, wide, 4x, 9x, or 16x
Normal, inverse, blinking, inverse blinking
Character designation ASCII
Graphics Polyline, circle
Note 1. If a displayed character string exceeds the line, that string is displayed beginning from the left side of the next line.
2. In addition, strings that do not fit at the bottom of the screen over-write from the top left side of the same screen.
44
SECTION 5
Input Functions
This section describes the functions used to input data on-screen. Functions used to create screens and control display attributes on the PT are described in Section 4 Display Functions. Data transfer and maintenance functions are described in Section 6 System Menu. Transferring screens online to and from the host computer is described in Section 7 Online
Transfer.
5-1 On-screen Switch Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-1-1 Transmitting to the Host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-1-2 Creating Touch Switches (DT Type Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-1-3 Using Function Keys
5-2 Inputting Numeric Settings
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-3 Standalone Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
47
47
50
46
46
46
45
On-screen Switch Inputs Section 5-1
5-1 On-screen Switch Inputs
The DT-type PT can transmit to the host the status of touch switches set on screens. A maximum of 64 switches can be set per screen. The DN-type can transmit to the host the inputs of 12-key Function Key Units and External I/O
Units.
5-1-1 Transmitting to the Host
There are two ways to transmit the status of switches to the host. These methods are described briefly below. For more detail, refer to the Host Inter-
face Unit Operation Manual.
Switch-Number Method When a switch is pressed, the number corresponding to that switch is transmitted to the host as a numeric value in three digits of BCD. When two switches are pressed, the first one is given priority in transmission. When using an NT600M-LK201 or NT600M-RT121/LB121 Host Interface Unit, send the data to the host by means of the strobe signal in the PT status information which is output when switches are pressed.
Bit-Switch Method The status of each switch is transmitted to the host as a bit status. This is the method used when substituting for ordinary operating switches. You can use it for ordinary bit input switches from a Programmable Controller. In order to use this method, you must set “bit input” in advance at the Support Tool or use the Host Link Interface direct connection function.
Note With this method, it is possible to push a number of switches simultaneously as long as they are in the same vertical row or the same horizontal column.
Do not simultaneously press switches that are in both different rows and in different columns. At the right in the following example, simultaneously pressing switches A, B, and D will automatically turn switch C to ON.
Switch B
Okay No
Switch A :Switches pushed down
Switch D
Switch C
For details, refer to the Host Interface Unit Operation Manual.
5-1-2 Creating Touch Switches (DT Type Only)
Just as with lamps, touch switches are created and registered with the Support Tool. The setting content is as follows:
Frame Display
Inversion at input time
Guide character
Standard/Cubic Type/Without
With/Without
With/Without
Setting Parameters
Number of Settings
Combine your choices of rectangular sections from the among the 72 blocks shown in the diagram below, and designate them as switches. Switches must be set in increments of these blocks.
You can set a maximum total of 64 switches per screen. If you wish, the whole screen can also be set as one input switch.
46
Inputting Numeric Settings
Screen Configuration Example
6
Section 5-2
12
Example of On-screen Touch Switches
Power error
Oil pres error
Auto Forwd
Man Back
Up
Down
Stop
5-1-3 Using Function Keys
The function keys all have the same size screen display frames. You can display customized function names on the screen to identify them. When a
12-key Function Key Unit or an External I/O Unit is connected to a DN-type
PT, the functions of the keys can be allocated. Up to two function keys can be pressed simultaneously when using an NT20M-FK210 Function Key Unit.
Example of Function Key Input Screen
Time Setting
PV
SV
56 s
1
7
2
8
3
9
4
0
5
CLR
6
+/–
5-2 Inputting Numeric Settings
Numeric values input while the numeric setting screen is being displayed are written to the designated numeral table and transmitted to the host.
Numeric Setting Screens The standard numeric setting screen is as shown below. This screen is reserved for system use by the Support Tool. Standard screen key arrange-
47
Inputting Numeric Settings Section 5-2
ments and functions are fixed. In order to change the key arrangement or add keys (such as a decimal point) for numeric input, set the “numeric setting” item under “screen attributes” to “user.” (When it is set to “system,” the standard screen will be displayed.) For instructions on registering numeric setting screens, refer to the NT-series Support Tool Operation Manual.
Standard Screen (Screen Attribute: System)
User-set Screen Example
(Screen Attribute: User)
1
7
2
8
3
9
4
0
5 6
CLR +/–
Tank A
0654
Tank B
0650
Tank C
0000
Tank D
0550
Tank E
0800
Tank F
0990
HOME MENU
1
4
7
0
2
5
8
3
6
9
↑
↓
←
.
CLR
→
CHANGE SET
Creating Numeric Setting
Screens
When creating a numeric setting screen with the Support Tool, take note of the following points.
1) A numeric setting screen cannot be set as the child screen of a continuous screen.
2) Ordinary touch switches can be set in numeric input screens, but touch switch numbers 244 through 255 cannot be used.
3) When “10-key” is set to “user” in the screen attributes, touch switch numbers 231 through 255 cannot be used for purposes other than numeric input.
4) The numeric setting function cannot be used when the screen attribute “bit input” is enabled for PTs with no touch panel.
Inputting Numeric Values
(PTs With Touch Panels)
1) Inputting Numeric Values with the Standard Screen:
• The numeral shifts from the rightmost digit to the left each time a screen key is pressed.
• If a decimal point is set, the shift is from the rightmost digit in the decimal area to the integer side.
2) Inputting Numeric Values with a User-set Screen:
•
The numeral shifts from the rightmost digit to the left each time a screen key is pressed.
•
If a decimal point is set, the integer portion is received first, and with each numeric key input there is a shift from the rightmost digit to the left.
•
When the decimal point key is pressed, the decimal portion will then be received. From that point on, with each numeric key input there is a shift from the rightmost digit in the decimal portion to the left.
Inputting Numeric Values
(PTs Without Touch Panels)
Use the 12-key Function Key Unit (NT20M only) or the 32/16 Terminal for an
External I/O Unit. The 10/02 Terminal cannot be used for numeric input.
1) Inputting Numeric Values with the Standard Screen:
Use the corresponding function keys. Numeric input is the same as for PTs with touch panels.
48
Inputting Numeric Settings Section 5-2
2) Inputting Numeric Values with a User-set Screen:
Use the corresponding function keys. Numeric input is the same as for PTs with touch panels.
Numeric Input Example
Direction Keys and Home
Key
Differences in Cursor
Movement
This example shows numeric input with a user-set screen. The display settings made with the Support Tool are as follows:
Number of digits displayed:
Number of integer digits:
Number of decimal digits:
Zero suppress:
Plus/minus mark display:
7
4
3
No
No
The following table shows the inputs and the resulting changes in the display.
Input operation
Initial display
Input “CLR”
Input “2”
Input “7”
Input “.”
Input “2”
Input “1”
Input “9”
Input “ ↵ ”
Set value
1234.567
0000.000
0002.000
0027.000
0027.000
0027.002
0027.021
0027.219
0027.219
Numeric values input with the input keys are stored in the numeral table justified to the right, as shown above. When the CLR Key is pressed for the first time, the initial display is cleared. If zero suppress were enabled, the number displayed would be “0.000” instead of “0000.000.” When the “2” is then input, it is registered at the rightmost integer position, as described on the preceding page. The “2” is then shifted to the left as the “7” is input. After the decimal point is input, numerals are then registered at the leftmost decimal position. (To return to integer input status, press the CLR Key again.) Finally, pressing the Enter Key causes the numeral table data to be transmitted to the host.
Pressing the direction keys (i.e., the arrow keys) moves the cursor to other numeric setting columns. Pressing the Home Key moves the cursor to the upper left of the screen.
When multiple numeric setting areas are created for a numeric setting screen, cursor movement will be different depending on whether system keys or touch switches are used.
Screen Example
Numeric setting 4
Numeric setting n: “n” represents the order in which numeric setting areas are created by the Support Tool.
Numeric setting 3
Numeric setting 1
Numeric setting 2
Numeric setting 5
Present cursor position
49
Standalone Function Section 5-3
1) When System Keys are Used:
When system keys are used, the cursor moves from area to area in the order in which the areas were created by the Support Tool. Thus, in the screen example shown above, the cursor would start at numeric setting 2 and move in order to numeric settings 3, 4, 5, and back to 1.
2) When Touch Switches are Used:
When touch switches are used, the cursor moves from area to area according to the layout of the screen. Thus, in the screen example shown above, the Down Key would move the cursor from numeric setting 2 to numeric setting 5. After that, the Down Key cannot move the cursor any further.
Pressing the Up Key would then move the cursor back to numeric setting 2, and then continue to move it upward in order to numeric settings 1 and 3.
The Right Key would then have to be used to move the cursor to numeric setting 4.
5-3 Standalone Function
When a screen for which the standalone function has been set by the Support
Tool is displayed, the screen can be changed by means of touch switches and function keys.
Example
Registered Screen Screen No. 5
Production Conditions Production Target
Screen 5 Touch switch no. 1 display area
Model no. NT600M-DT122
Number produced
2,500
Items Registered to Screen by Support Tool
• Standalone function setting
• Touch switch or function key number
•
Screen number to be displayed when touch switches or function keys are input
Example
Standalone function is set.
Touch switch number: No. 1
Screen to be displayed: No. 5
Production target: 5,000
Number produced: 2,500
Number defective: 2
When touch switch no. 1 is input, screen no. 5 is displayed.
50
SECTION 6
System Menu
This section describes data transfer and maintenance functions. Functions used to create screens and control display attributes on the PT are described in Section 4 Display Functions. Functions used to input data on-screen are described in
Section 5 Input Functions. Transferring screens online to and from the host computer is described in Section 7 Online
Transfer.
6-1 Configuration of System Menu
6-2 System Menu
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-2-1 Quit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-2-2 Transmit Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-3 Maintenance Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-3-1 Display History
6-3-2 I/O Checks
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-3-3 PT Settings Check
6-3-4 Initialization
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-4 Memory Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
53
53
53
56
52
53
53
58
60
60
51
Configuration of System Menu Section 6-1
6-1 Configuration of System Menu
The system menu is used to set PT system parameters in advance and perform maintenance. With the system menu you can, in addition to determining the PT’s status, check switch settings and perform simple I/O checks.
SYSTEM MENU
Quit
(1) If there is no key input within 10 s, the original screen will be automatically reset.
(2) The RUN indicator will be OFF during system menu operations.
Transmit Mode
Maintenance
Mode
Quit Display History I/O Check Status Check Init. Memory Memory SW
Occur.
Freq.
Quit Init. Screen Init. Table Init. History
Quit Key Press Sound Backlight Off Resume
Quit Function Key Touch Switch Comm. Check LCD Display Key Press Sound Backlight Check
Tool I/F Host I/F
To return to the original screen after selecting Maintenance Mode, do one of the following:
Select Quit, and press the Enter Key.
Or press the Buzzer Key, Up Key, and Down Key simultaneously.
The RUN indicator on the front panel is OFF while the System Menu is being displayed.
52
Maintenance Mode Section 6-3
6-2 System Menu
6-2-1 Quit
The System Menu is called up by using the system keys during operation. To leave the System Menu and return to RUN Mode, select Quit. If no key is pressed for 10 seconds, the PT will automatically return to RUN Mode.
SYSTEM MENU
Quit
Transmit Mode
Maintenance Mode
For details on key operation and content, refer to 3-2 Initialization.
6-2-2 Transmit Mode
This mode is used to transfer data between the PT and the Support Tool.
6-3 Maintenance Mode
When making PT system settings or when there is an operating error, select
Maintenance Mode and conduct all the checks.
Maintenance Mode Menu
MAINTENANCE MENU
Quit
Display Hist.
I/O Check
PT Settings
Init. Screen
Init. Hist.
6-3-1 Display History
The PT saves into memory and can display the history of screens displayed during operation if the history attribute is set for them. The history can be displayed either in order of occurrence or in order of frequency. This function can be used to help identify the causes of malfunctions or to enable the operator to know which functions are often being used.
Setting History Data When creating screens with the Support Tool, use screen attribute designations to register history attributes and messages (within 24 characters) for the screens you want to save in the history.
53
Maintenance Mode
Reading History Data
Section 6-3
Whenever the screen number registered for history attributes is designated by the host, the occurrence and message are saved in memory.
• The capacity of the history is 256 screens.
•
The only things that can be recorded are screen numbers and messages.
History record data is backed up by a battery, so, as long as the lithium battery is installed, the contents will be retained even when the power is turned off.
• Before beginning to record, initialize the history data by transmitting an Initialize History command from the host, or by selecting Init. Hist. from the
Maintenance Mode.
• If the history data capacity is exceeded, newly occurring history data will not be saved.
Enter Maintenance Mode from the System Menu.
MAINTENANCE MENU
Init. Screen
Init. Hist.
Display Hist.
I/O Check
PT Settings
Order of Occurrence
Move the bar cursor to History Record by pressing the Up and Down Keys.
Then press the Enter Key.
History Record
Occurrence
Frequency
Select whether the history is to be displayed in order of occurrence or in order of frequency. First move the bar cursor to your selection by means of the
Up and Down Keys, and then press the Enter Key.
Record data is displayed in order of occurrence.
No.
Of
1
5
200
150
Times
( )
( )
( )
( )
Message
Coolant Mal.
Motor Mal.
Comp. Mal.
Press
Number of times occurred.
Screen number
54
Maintenance Mode
Order of Frequency
Section 6-3
•
One screen displays six items of record data.
•
If not all of the record data shows on the screen, then use the Down Key to scroll down.
•
To return to RUN mode, press the Buzzer Key, Up Key, and Down Key simultaneously.
•
When record data is displayed chronologically, the chronology number is not displayed.
Record data is displayed in order of frequency.
No.
Of Times
200
1
5
( 2)
( 1)
( 1)
Message
Comp. Mal.
Coolant Mal.
Motor Mal.
When different messages occur with the same frequency, they are displayed in order beginning with the lowest screen number.
When there is no display data, the following message will be displayed (for both order of occurrence and order of frequency).
History Record Not Found
Initializing History Data If you select Init. Hist. from the Maintenance Mode menu, the history data which is currently recorded will be deleted. Select Maintenance Mode from the System Menu. The Maintenance Mode Menu will be displayed.
MAINTENANCE MENU
Init. Screen
Init. Hist Display Hist.
I/O Check
PT Settings
Move the bar cursor to Init. Hist. by pressing the Up and Down Keys. Then press the Enter Key.
Initialize History?
Yes
No
Select whether or not the history will be initialized. If you select Yes, then initialization will be executed. All recorded history will be deleted. If you select
No, then operation will commence without initialization.
55
Maintenance Mode
6-3-2 I/O Checks
Section 6-3
In the Maintenance Mode Menu, use the Up and Down Keys to move the bar cursor to I/O Check. When you then press the Enter Key, the following menu will be displayed.
I/O CHECK MENU
Quit
Function Key
Touch Switch
Comm. Check
LCD Display
Buzzer
Backlight Check
Move the bar cursor to the item you want to check, and then press the Enter
Key.
Function Key Check
F33
F41
F49
F57
F1
F9
F17
F25
F34
F42
F50
F58
F2
F10
F18
F26
F35
F43
F51
F59
F3
F11
F19
F27
F36
F44
F52
F60
F4
F12
F20
F28
F37
F45
F53
F61
F5
F13
F21
F29
F38
F46
F54
F62
F6
F14
F22
F30
F39
F47
F55
F63
F7
F15
F23
F31
F40
F48
F56
F64
F8
F16
F24
F32
The operation of the function keys can be checked if a 12-key Function Key
Unit is connected. Press a function key. If the number of that key is displayed in reverse video on the screen, then it is operating properly. Key numbers are not transmitted to the host during the check operation. Up to two keys can be pressed simultaneously.
The NT20M-FK210 has 12 standard function keys, so you can use F1 to
F12.
To return to the I/O Check Menu, press the Buzzer Key, Up Key, and Down
Key simultaneously.
Touch Switches (DT-type
PTs)
External Function Key Input
Check
A touch switch operation check can be carried out for PTs with touch panels (i.e.,
DT-type PTs) by pressing each switch displayed on the screen. If a given switch is displayed in reverse video after being pressed for approximately 0.5 second, then that switch is okay. If “key input sound” is set to ON in the Memory Switch
Menu in Maintenance Mode, then the buzzer sounds simultaneously with the reverse video display. The switch numbers are not transmitted to the host.
To return to the I/O Check Menu, press the Buzzer, Up, and Down system keys simultaneously.
When external input terminals turn ON, the corresponding function keys are displayed in reverse video. When a 12-key Function Key Unit is connected, F1 through F12 correspond to IN0 through IN11.
56
Maintenance Mode Section 6-3
To return to the I/O Check Menu, press the Buzzer, Up, and Down system keys simultaneously.
F1
F9
F2 F3 F4 F5 F6 F7 F8
F10 F11 F12 F13 F14 F15 F16
F17 F18 F19 F20 F21 F22 F23 F24
F25
F33
F26 F27 F28
F34 F35 F36
F29
F37
F30
F38
F31
F39
F32
F40
F41 F42 F43 F44 F45 F46 F47 F48
F49 F50
F57 F58
F51 F52
F59 F60
F53 F54 F55 F56
F61 F62 F63 F64
Lamp Output Check When “lamp output check” is be displayed in reverse video, L1 will light. This indicates that output 1 is ON. Use the Up Key and the Down Key to move from lamp to lamp to check their respective outputs. When the Up Key is pressed, the next lamp to the right is displayed in reverse video. When the Down Key is pressed, the next lamp to the left is displayed in reverse video.
When a 32/16 Terminal or a 10/02 Terminal is connected, the output corresponding to the lamp displayed in reverse video turns ON.
To return to the I/O Check Menu, press the Buzzer, Up, and Down system keys simultaneously.
L1
L9
L2
L10
L3
L11
L4
L12 L13
L20
L5
L21
L6 L7
L14
L22
L8
L15 L16
L23 L24 L17 L18 L19
L25
L33
L26
L34
L27
L35
L28 L29
L36 L37
L30
L38
L41 L42
L49 L50
L57 L58
L43
L51
L59
L44
L52
L60
L45
L53
L46
L54
L61 L62
L31
L39
L47
L55
L32
L40
L48
L56
L63 L64
Communications Check
Note If a load (e.g., a buzzer or alarm light) is connected to a 10/02 Terminal or a 32/16
Terminal, it will actually operate. This can potentially be dangerous, so take the necessary precautions.
When “Communications Check” is selected, the Communications Check Menu will be displayed.
COMMUNICATIONS CHECK MENU
Tool Interface
Host Interface
Select one
Tool Interface Check
Tool Interface
Data received from a connected Support Tool is displayed as is, in hexadecimal.
If any numbers are displayed, that means that the tool interface is okay. If nothing is displayed, then there may be a Support Tool, communications cable, or communications hardware error.
Data transmitted from the Support Tool is displayed in hexadecimal.
57
Maintenance Mode Section 6-3
Tool I/F Input Check
1B 24 15 20
Host Interface (NT600M-LK201)
RS-232C I/F Input Check
1B 51 30 33
Data which is received will be displayed in hexadecimal.
Host Interface (NT600M-LK202)
RS-422 I/F Input Check
1B 24 15 20
Data which is received will be displayed just as it is, in hexadecimal.
LCD Display Check
Buzzer Check
The lines of the display are reversed one at a time, starting from the top of the screen. When the reversal is finished, then they are cleared one at a time. When all of them have been cleared, the I/O Check Menu is returned to. You can interrupt the check and return to the I/O Check Menu by pressing the Buzzer Key, Up Key, and Down Key simultaneously while the check is in progress.
By selecting “Buzzer” from the I/O Check Menu, the PT buzzer can be checked. The buzzer should produce a continuous sound. To stop the buzzer, press the Buzzer Key. While the buzzer is sounding, it will not be possible to change screens or stop the buzzer by pressing the Buzzer Key, Up Key, and Down Key simultaneously. The NT2000M has a buzzer enable/disable pin. If this pin is removed, the buzzer cannot sound.
Backlight Check If “Backlight” is selected, the cycle from white (1 s) to red (1 s) to off will be repeated. To stop the backlight check, press the Buzzer Key, Up Key, and
Down Key simultaneously. The NT20M-DT121-EV2 and the NT20M-
DN121-EV2 do not have red backlights.
6-3-3 PT Settings Check
The status of the PT and Host Interface Unit can be displayed, as well as the settings of switches. Select “PT Settings” from the Maintenance Mode Menu.
58
Maintenance Mode
Internal Settings
Section 6-3
There are two screens, one for the PT and one for the Host Interface Unit, and you can scroll up and down with the Up and Down Keys.
When PT Settings is selected, the internal settings of the PT are displayed first.
Page
↓
PT Settings
Memory Type
Memory Size
Mode Changes
Exp. I/O Unit
RAM
128 KB
No
Standard (See Note 2)
Note 1. Memory type and memory size are displayed only when the screen data memory has been initialized. If it has not been initialized, then “N.A.” is displayed.
2. If the PT is a DN type, and if an Expansion I/O Unit is connected, then the types of Expansion I/O Unit will be displayed.
Standard: 12-key Function Key Unit
Not Connected
• If an 12-key Function Key Unit becomes disconnected during operation, a continuous buzzer will sound and a “No Expansion I/O Unit” error message will be displayed.
•
To clear the error message, turn off the power supply and reconnect the
Expansion I/O Unit. Then turn the power supply back on.
Host Interface Unit Settings To display the DIP switch settings on the Host Interface Unit, press the Down
Key while the PT settings are being displayed.
RS-232C Host Link Units (NT600M-LK201)
Page
↑
RS-232C I/F Settings
Data Length
Stop Bits
Parity
Flow Control
Baud Rate
7 bits
2 bits
Even
XON/XOFF
9600 bps
RS-422 Host Interface Units (NT600M-LK202)
RS-422 I/F Settings
Terminal No.
Data Length
Stop Bits
Parity
Flow Control
Baud Rate
01
7 bits
2 bits
Even
No
9600 bps
Page
↑
For details on other Host Interface Unit models, refer to the Host Interface
Unit Operation Manual. To return to the Maintenance Mode Menu, press the
Buzzer Key, the Up Key, and the Down Key simultaneously.
59
Memory Switch Settings Section 6-4
6-3-4 Initialization
You must initialize the image data memory when using the SRAM or EE-
PROM for the first time. Initialization can also be used to clear all or part of the data already registered in the PT.
Initializing Memory If you select Init. Memory in Maintenance Mode, a screen will be displayed providing a selection of data to be initialized (i.e., image data, memory table data, or history data). After one of the choices has been selected, another screen will be displayed to confirm that you actually want to initialize that data.
If you select Yes, then initialization will be executed and all of the selected data will be deleted. (If memory table data is initialized, then the values set by the Support Tool will be restored.
6-4 Memory Switch Settings
Memory switch settings set the NT20M display and key input sounds.
Select “Memory SW” from the Maintenance Mode Menu.
MAINTENANCE MODE MENU
Quit
Display History
I/O Check
PT Settings
Initialize Memory
MemorySwitch Select one
Liquid Crystal Display Type Move the cursor to the item that is to be set and press the Enter Key. Each time that it is pressed, the set value will change.
After the settings have been made, press the Buzzer, Up, and Down keys to return to RUN Mode. If the power to the NT20M is turned off at this point, the settings will not be registered.
MEMORY SW MENU
Quit
Key Input Sound
Backlight Off
Display
Resume Function
ON
10 min
Normal
ON
60
Memory Switch Settings
EL Display Type
Section 6-4
MEMORY SW MENU
Quit
Key Input Sound
Residual Image Elimination Function
Resume Function
ON
1 hr
ON
Contents of Settings
Item
Key input sound
Backlight off (LCD type)
Display (LCD type)
Residual image elimination function (EL type)
Resume function
ON
OFF
Setting
10 min
Contents
The buzzer sounds for 0.2 second when a system key, touch switch, or function key is input.
The buzzer does not sound when a system key, touch switch, or function key is input.
If no key input (see note 1) or command (see note 2) is received for 10 minutes while a screen is being displayed, the backlight turns off.
If a backlight-off command is transmitted from the host, the backlight turns off regardless of this setting.
1 hr
None
Normal
OFF
If no key input (see note 1) or command (see note 2) is received for one hour while a screen is being displayed, the backlight turns off.
The backlight stays on constantly.
The screen display is normal.
Reverse video The screen is displayed with dark and light reversed.
10 min If no key input (see note 1) or command (see note 2) is received for 10 minutes while a screen is being displayed, the screen turns off.
1 hr
None
If no key input (see note 1) or command (see note 2) is received for one hour while a screen is being displayed, the screen turns off.
The screen stays on constantly. The residual image eliminationfunction does not operate, so turn off the screen periodically by means of the host program.
ON The contents of memory tables written by the host during operation are retained even if the NT20M power turns off or a reset is executed.
If power to the NT20M is turned off or a reset is executed, the contents of the memory table are overwritten by the contents of data created by the Support Tool.
Operating Conditions for the Backlight Off and
Residual Image
EliminationFunctions
Note 1. Key Inputs
System keys, touch switches, function keys
2. Commands
Screen-change command
Setting screen overlap command (serial systems only)
On-line transfer completed command (Restart with change to RUN Mode)
Backlight-on command
3. The shaded areas represent the default settings.
When either “backlight off” or residual image elimination” is set to either “10 minutes” or “one hour,” the internal timer starts counting as soon as the key input or command is received. When the time is up, the backlight or EL screen turns off.
The relevant key inputs and commands are as follows:
61
Memory Switch Settings Section 6-4
Resume Function
Display Examples
When any one of the above key inputs or commands is received, the backlight will be turned back on and the internal timer will start counting again. If a key input or command is then received before the time is up, the timer will be reset and the count will start over.
The resume function retains character string and numeral table data when power is interrupted or when the reset switch is pressed.
1, 2, 3...
1. When the Resume Function is Set to Off
The contents of character string and numeral tables are cleared when the power to the PT is turned off or when the reset switch is pressed. After the power is turned back on, or after the reset, character string and numeral table data is read from the screen memory and operation begins again. If new character string or numeral table data is transferred from the Support
Tool, that new data overwrites the data in the memory tables.
2. When the Resume Function is Set to On
If the power to the PT is turned off, or if the reset switch is pressed, the character string or numeral table data prior to the power interruption or reset is retained. If new character string or numeral table data is transferred from the
Support Tool, the contents of the screen memory are refreshed but the memory table data does not change. In order to return the contents of the memory tables to the initial values that were created by the Support Tool, execute “initialize memory table.”
Depending on the setting of the resume function, the display at the time of powering up will be as follows:
Display after power is turned back to ON or after reset.
Display at beginning of operation.
Display just prior to power interruption or reset.
9999
XYZ
When resume function is set to ON.
0123
ABC
9999
XYZ
The initial values created by the Support
Tool are displayed.
Memory Table Data
0123
ABC
When resume function is set to OFF.
Power turned OFF or reset switch pressed.
62
SECTION 7
Online Transfer
This section describes transferring screens online to and from the host computer. Functions used to create screens and control display attributes on the PT are described in Section 4 Display Functions. Functions used to input data on-screen are described in Section 5 Input Functions. Data transfer and maintenance functions are described in Section 6 System
Menu.
Screen data can be transmitted online (i.e., in RUN Mode) by means of a Host Interface Unit command. For details on commands, refer to information on online transfers in the Host Interface Unit Operation Manual. This function is valid only for RS-232C and RS-422 Host Interface Units.
7-1 Transferring Screen Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-2 Host to PT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-3 PT to Host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-4 Online Transmission and Resume Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
64
64
64
65
63
PT to Host Section 7-2
7-1 Transferring Screen Data
Screen data can be transferred along with screen numbers. Set the desired screen number. If you set a screen number which is identical with one already registered in the PT, then the screen data for that number will be overwritten.
In addition to screen data, you can transfer memory tables and marks.
7-2 Host to PT
Screen data is transferred along with screen numbers. Any screen numbers can be set. You can make a setting to transfer all screens or a screen of your choice.
In addition to screen data, you can transfer memory tables, marks, and history.
If data transmission is interrupted by a system key operation, the data received up to that point will be stored, but all data after that point will be corrupted.
If transmission of mark data is interrupted, the mark data will be received but the accuracy of the data cannot be ensured. When the System Menu is brought up, a message will be displayed indicating that the mark data has been corrupted.
Screen during online transfer processing
Transmit Mode
Shows direction of data transfer.
PT ––> Host
Host ––> PT
Screen Data
System Memory
Memory Tables
Mark Data
History Info
Shows type of data.
KB
Number of bytes transferred (in kilobytes).
7-3 PT to Host
Screen data can be transferred along with screen numbers. All screens or desired screens can be transferred.
The memory table, mark, and display history can be transferred as well.
Screen data will not be corrupted when data transfer is interrupted with the
System Key.
64
PT to Host Section 7-2
7-4 Online Transmission and Resume Function
Online transfer enables the Host to write data directly to the screen data memory just like data transfer to the Support Tool. Therefore, the contents of the display are influenced by the settings of the resume function.
Display after data reception Display after reception of data from the Host
9999
XYZ
Reception
9999
XYZ
Resume function turned ON
New data transfer on the Host side
2752
XYZ
2752
XYZ
Resume function turned OFF
65
SECTION 8
Maintenance and Inspection
This section provides troubleshooting and basic maintenance methods, including battery replacement.
8-1 Checking Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-2 Changing the Lithium Backup Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-3 Replacing the Backlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-4 Maintenance and Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-4-1 Spare Terminals
8-4-2 Inspection
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
68
69
70
71
71
71
67
Checking Operation Section 8-1
8-1 Checking Operation
The hardware status of the PT can be checked with the Maintenance Menu.
Symptoms and corrective measures for errors that cannot be checked are shown in the table below.
Symptom
POWER indicator does not light.
Probable cause Corrective measures, processing
Power is not being input, or power supply is connected in inverse.
Provide a power supply with a rated voltage of 24 VDC.
Do not reverse polarity.
A fuse is blown.
Contact your OMRON representative.
No Host Interface Unit is mounted.
Mount a Host Interface Unit.
Message indicates no
Host Interface.
Screen does not display.
The System ROM is not compatible with the Host Interface Unit.
System ROM is not installed, or connections are faulty.
The memory installed does not match the settings of SW2, or no memory chip is installed.
Contrast is not correct.
Cannot communicate PT is not in Transmit Mode.
with Support Tool.
There is a faulty connection with the Support Tool.
Cannot communicate Switch settings are not correct.
Match the specifications of the System ROM and the
Host Interface Unit.
Check to be sure that the System ROM is installed, and tighten the screws.
Install a memory chip in socket and set SW2 correctly.
Adjust the contrast with the contrast control.
Select Transmit Mode from the System Menu.
Check connecting cables.
U it ( i l communications)
Cannot communicate using Host Interface
Unit (parallel communications)
Lamp status is retained when screens are changed.
The buzzer sounds, the RUN LED indicator goes out, operation suddenly stops, or the display goes off and does not return.
Screen suddenly goes blank.
Corrupted Screen
Data
Host Interface Unit connections are faulty.
For the NT600M-LK202, terminator settings are not correct.
The timing is off for communications with the host interface.
Lamps and touch switches are overlapping.
1) System ROM is not properly installed.
2) Malfunction occurred due to external noise.
Screen has changed to screen no.
0 at the host.
Screen data memory is bad.
The power was turned off or the reset button was pressed during transmission
Check PT settings under the Maintenance Mode and be sure that settings match the host settings.
Check wiring of connecting cables.
Use shielded wire.
Check whether the cables are within the maximum lengths.
When using RS-422 communications, specify only the last Terminal from the host as the terminator (turn on termination resistance on the last Terminal only).
Check the timing of the DIP switch settings and the host’s clock output.
Conduct a check using the “Communications Check” in
Maintenance Mode.
Use touch switches as lamps just as they are. (Touch switches have lamp functions.)
1) Install the System ROM properly and lock it securely in place.
2) Remove the communications cable from the source of noise. Attach a noise filter to the power supply line.
There is no error.
1.) Replace the memory.
2.) Initialize the screen data memory and re-transfer the data.
68
Changing the Lithium Backup Battery Section 8-2
8-2 Changing the Lithium Backup Battery
A lithium battery is used in the NT20M and in the NT2000M. If the BAT LOW indicator on the front panel lights, replace the battery within ten days.
Battery model
Battery backup time
Replacement time
3G2A9-BAT08
5 years at 25 ° C.
Within 5 minutes from the time power is turned off.
Replacing the Battery
1, 2, 3... 1.
Turn the power off. If the power has not been on, turn it on for at least one minute and then turn it off again before replacing the battery.
2.
Take off the battery cover on the back of the PT.
3.
Remove the battery from the connector and put in a new battery. Be sure that the connector is straight when inserted.
Note a) Do not take more than five minutes to replace the battery, otherwise the internal memory may be lost.
b) The battery can be replaced with the PT turned on, in which case there is no limitation for battery replacement time.
Caution Be sure not to touch the internal circuitry when replacing the battery with the
PT turned on, otherwise the internal circuitry may be short-circuited or an electric shock accident may result.
NT20M
Battery connector
Battery Set 3G2A9-BAT08
NT2000M
Battery Set
3G2A9-BAT08
Battery connector
4.
Replace the cover.
Caution The lithium battery can explode if placed into a fire, or it can explode, burn, or leak if the + and – terminals are short-circuited or if the battery is recharged or dismantled. Handle the battery with care.
Note If no battery is connected, BAT LOW indicator operation is not stable.
69
Maintenance and Inspection Section 8-4
8-3 Replacing the Backlight
The backlight can be replaced for NT20M-DT13 j
, NT20M-DN j
, and
NT2000M-D j
131 PTs. When the screen begins to flicker or get darker, replace the backlight by replacing the CFL Unit.
CFL Unit model For NT20M: NT20M-CFL01
Service life (See note)
For NT2000M: NT200M-CFL01
Approx. 20,000 hours at 25 ° C.
Note The service life is taken to be the time it takes for the backlight to lose 50% of its brightness.
NT20M-DT/DN13 j
Backlights
1) Turn off the power to the PT.
2) Pull out the backlight cover on the right side of the PT by placing your finger on the top and pulling it forward.
NT20M
Cover
3) Pull out the attached CFL Unit cord and slowly pull off the connector, being careful to pull it straight.
CFL Unit
Lock mechanism
Cord
Connector
4) On the right side of the CFL Unit there is a latch. Bend it to the left (i.e., to the side of the PT display panel) to unlock the CFL Unit from the print board.
Then pull the CFL Unit straight out. Be careful not to directly touch the fluorescent tube.
Lock mechanism
Latch
5) Insert the new CFL Unit, and bend the latch back to lock the CFL Unit to the print board. If it is difficult to insert it, the cord may be getting in the way.
Do not try to force it, but just push the cord to the top and insert the CFL Unit slowly.
6) Insert the connector, being careful to match the polarity. Fit the cord in and replace the cover.
70
Maintenance and Inspection
NT2000M-D j 131
Backlights
Section 8-4
1) Turn off the power to the PT.
2) Remove the backlight case at the rear of the PT, by pressing on the place where it is indicated and pushing upward.
Hooks
3) Pull off the attached CFL Unit connector and remove the CFL Unit.
Latches
CFL Unit
Connector
4) Install the new CFL Unit and insert the connector, being careful to match the polarity.
5) Replace the backlight case, and snap it carefully in place.
Latch
Hook
Notch
Caution To avoid electrical shock, be sure to turn off the power before removing the backlight cover.
Be sure to put the cover back on after replacing the CFL Unit.
8-4 Maintenance and Inspection
8-4-1 Spare Terminals
In order to restore operations as quickly as possible in the event of a PT breakdown, it is a good idea to always keep a spare PT on hand.
8-4-2 Inspection
If the PT screen gets dirty, it will become hard to read. Be careful of the following points when cleaning it.
• When cleaning, wipe with a dry, soft cloth. If the dirt does not come off, then moisten the rag with water and rub hard.
71
Maintenance and Inspection Section 8-4
•
Wiping with a chemical cloth or with volatile solutions such as benzine or thinner may cause degeneration. A little alcohol may be used if necessary.
•
Prolonged contact with rubber, vinyl products, or tape may leave marks.
• The PT’s liquid crystal display and backlight can wear out. If they become hard to see, replace the PT. The backlight of the NT20M-DT121-V2 or
DN121-V2 cannot be replaced.
• The standard inspection period is once every 6 to 12 months, but it should be moved up if the operating environment is harsh. If there is any deviation from the criterion, then it should be corrected.
Inspection item
Power supply
Operating environment
Installation
Replaceable parts
Inspection content Criterion
Measure at the power supply terminal block. Are voltage fluctuations within the criterion?
Is the ambient temperature (the temperature inside of the panel) suitable?
Is the ambient humidity (the humidity inside of the panel) suitable?
Is dust collecting?
Is each Terminal firmly secured?
Voltage fluctuation range:
NT20M: 20.4 to 26.4 VDC
NT2000M: 85 to 264 VAC
NT20M: 0 ° C to 45 ° C
NT2000M: 0 ° C to 50 ° C
35% to 85% There should be no condensation.
There should be no dust.
There should be no loose screws.
Are the connectors for the connecting cable inserted perfectly and locked?
There should be no loose screws.
Are any screws for the external wiring coming loose?
There should be no loose screws.
Is any external wiring loose or disconnected?
There should be no external abnormalities.
Can you read the characters on the liquid crystal display?
Is the backlight illumination as bright as it should be?
Average life expectancy of liquid crystal: 50,000 hrs
Average life expectancy of backlight: 20,000 hrs
Method/tools
Tester
Thermometer
Hydroscope
Visual
Phillips screwdriver
---
Phillips screwdriver
Visual
Visual
Precautions for Handling
•
Turn off the power before replacing a PT.
• When you discover what seems to be a defective PT, check it again before replacing it to be sure that the problem is actually with the PT.
•
When returning a defective PT for service, please describe the problem in as much detail as possible. Send the PT to the OMRON office closest to you.
Tools for Inspection
•
Phillips and flat-blade screwdrivers
• Voltage tester or digital voltmeter
•
Industrial alcohol and all-cotton cloth
Measuring Instruments (Depending on Case)
•
Synchroscope
• Oscilloscope with pen output
•
Thermometer
•
Hydroscope
72
Appendix A
Standard Models
RS-232C Connecting Cable for Connecting Devices (CV500-CN228)
2 ,000
+150
–0
Note The personal computer end of the CV500-CN228 Connecting Cable is a 25-pin D-sub male connector. To connect to an IBM PC/AT or compatibles, a 9-pin or 25-pin D-sub female adapter is required.
Dustproof Cover
NT20M-KBA01 (for NT20M-DT/DN)
NT20M-KBA02 (for NT20M-DN connected to NT20M-FK210)
Under severe conditions, this cover can be used to protect the display area and controls from oil and dust.
112.4
±
0.3
Material: Silicon rubber
5.7
222.4
±
0.3
NT20M-KBA01 dimensions (mm)
NT20M-CFK01 Key Sheets (Five Sheets)
Use these sheets for NT20M-FK210 function keys. By simply peeling them off of the paper, you can easily write on them and attach them. You can also rub off anything written with oil-base ink. If they get dirty, you can easily remove and replace them.
Square hole
73
Standard Models Appendix A
NT20M-KBA03 Oil Resistance Kit
Mount this kit to the display panel of the NT20M to protect from dirt and oil. (This kit cannot be mounted at the same time as an NT20M-FK210 Function Key Unit. In addition, when it is mounted it is not possible to access under the Support Tool connector cover.
Six M3 flat-head screws
96 124 133
206
230
243
7.9
74
Appendix B
Specifications
General Specifications
Item
Power supply voltage
Allowable power supply voltage range
Power consumption
Insulation resistance
NT20M
24 VDC
20.4 to 26.4 VDC, (24 VDC –15% /
+10%
)
NT2000M
100 to 240 VAC
85 to 264 VAC (50/60 Hz)
Voltage resistance
12 W max.
___
___
40 VA max.
20 M Ω min. (at 500 VDC megger) between the AC external terminals and the GR terminal
2300 VAC max. for 1 min. at 50/60 Hz
(Leakage current: 0.8 mA max.)
AC 1,000 V
P-P
Pulse width:
Pulse rise time:
100 ns to 1
1 ns m s
Noise resistance (24 VDC)
Vibration resistance
Shock resistance
Common (between power supply and panel):
Normal:
Pulse width:
Pulse rise time:
1,000 V
P-P
300 V
1 ns
P-P
100 ns to 1 m s
10 Hz to 22 Hz: 1.5-mm double amplitude
X, Y, and Z directions
22 Hz to 500 Hz:
Acceleration: 1.5 G (14.7 m/s
2
)
X, Y, and Z directions for 30 min total
30 G (294 m/s 2 )
3 times each in X, Y, and Z directions
20 G (196 m/s 2 )
3 times each in X, Y, and Z directions
0 ° C to 45 ° C (with no freezing)
10 Hz to 50 Hz: 0.5-mm single amplitude;
Acceleration: 2.0 G (19.6 m/s
2
)
X, Y, and Z directions for 1 hour each
Ambient operating temperature
Ambient operating humidity
Operating environment
Storage temperature
Allowable power interruption time 1)
Enclosure ratings
Weight
Dimensions
35% to 85% (with no condensation.)
No corrosive gas
–20 ° C to 70 ° C (with no freezing)
5 ms max. (one minute or more after power is turned on)
Front control panel IP52F (Drip-proof when dust cover is installed, as long as
NT20M-FK210 is not mounted.)
Rear case:
Terminal section
IP20
IP00
1.2 kg max.
220 (W) x 110 (H) x 82 (D)
0 ° C to 50 ° C (with no freezing)
20 ms max.
IP65F or equivalent. Do not expose to direct jet stream for longer than one minute.
Approx. 3 kg
365 (W) x 232.5 (H) x 77 (D)
Note 1.
Even if a power interruption is outside of the allowable range, PT operation can still be continued but there is a possibility of data being corrupted if it occurs during communications with the Support Tool or the host when PT settings are made with system keys.
75
Specifications Appendix B
Characteristics
Display Specifications
Item
Display screen
Indicators Three indicators:
POWER indicator (Green LED):
RUN indicator (Green LED):
BAT LOW indicator (Red LED):
Specifications
Dot matrix STN liquid crystal display panel
No. of dots: 256 x 128
NT20M: j 0.407 mm
NT2000M: j 1.04 mm
Effective display area: NT20M: 112 mm x 56 mm
Service life expectancy:
NT2000M: 275 x 138 mm
50,000 hrs min.
View angle (right/left direction)
NT20M-D j 12 j :
NT20M-D j 13 j
NT2000M-D j 131
± 30 °
± 40 ° (when white backlight is lit)
± 45 ° (when red backlight is lit)
Backlight
White cold-cathode tube (NT20M-D j 13 j and NT2000M-D j 131 can change between red and white backlights.)
Service life expectancy:
Automatic turn-off:
10,000 hrs min. (20,000 hrs average)
Can be set to not turn off, or to turn off in 10 min or 1 hr
Lit when power is being supplied.
Lit during operation.
Lit when battery voltage level drops.
Control Panel Specifications
System keys
Item
Touch panel (DT type)
12-key Function Key Unit
NT20M-FK210 (Connectible to NT20M-DN type)
Specifications
Four keys: buzzer-stop, up-scroll, down-scroll, execute (enter)
Functions: System Menu selection, buzzer off, bar cursor movement, up/down scroll for continuous screens, execution of numeric settings
Maximum: 64 touch switches per screen
Pressure-sensitive
Operating force: 100 g max.
Life expectancy: 1,000,000 operations min.
No. of keys: 12 (fixed)
Switch type Pressure-sensitive
Key sheets are replaceable.
Note The 2-point output is the contact relay type. For the socket type, it can be replaced by a no-contact relay such as a transistor or triad.
Display Capacity
Item
Display characters
Number of characters displayed
Enlargement function
Display attributes
Character displays
Graphics
Terminal mode
String displays
Numeral displays
Specifications
Half-size characters (8 x 8 dots): Alphanumerics and symbols
Normal characters (8 x 16 dots): Alphanumerics and symbols
Marks (16 x 16 dots): User defined, 64 max.
Standard-size characters: Max. 32 characters horizontal x 8 vertical
Wide characters: Max. 16 characters horizontal x 8 vertical
Horizontal, vertical, 4 times, 9 times, 16 times
Inverse, blinking, inverse blinking
Displays any characters (screen number designation).
Polylines (broken continuous line) and circles
Characters, numeric values, and graphic designated by the host are displayed
(RS-232C or RS-422 interface required).
Maximum 32 total, 8 per screen and 32 bytes per string
Maximum 128 total, 50 per screen
76
Specifications Appendix B
Item
Bar graph display
Overlapping screens
Continuous screens
No. of registered screens
Screen registration method
Screen saving method
Screen attribute settings
Specifications
2 to 255 dots; +/– area display;% display capability
Overlapping of a maximum of 8 registered screens is possible.
Scrolling the display for a maximum of 8 registered screens is possible.
250 max.
Transfer to the PT data created at IBM PC/AT compatible, or mount EPROM chip containing data.
Can be saved to SRAM (with backup battery), EEPROM or EPROM.
Alarm, continuous buzzer, intermittent buzzer, function key bit input, touch switch bit input, display history, 10-key, backlight
Data Quantities
Item
Mark data
String data
Numeral data
Switches
Lamps
Specifications
64 max.
32 characters (standard size characters) x 32 strings max.
8 digits x 128 values max.
Switches and lamps combined: 256 max.
(There is no limit when Host Link direct connection is used.)
Special Features
Alarm output
Item
Host RUN input
Buzzers
Maintenance functions
Battery backup
Key input sound setting
Specifications
Relay output on rear terminal block.
Rating: NT20M: 1 A at 24 VDC
NT2000M: 1 A at 24 VDC
Output condition: NO contact (Closes when a command is received from the host or when there is a screen called with an alarm-ON specification.)
Photocoupler input on rear terminal block.
Rating 24 VDC +10% /
–15%
When this input goes OFF, the PT will display “host error” regardless of other conditions.
Two types: Continuous sound and intermittent sound.
ON: The buzzer will sound when a command is received from the host, or when a screen with a buzzer-ON specification is called.
OFF: The buzzer is turned OFF when the Buzzer Key is pressed, when a command is received from the host, or when a screen without a buzzer-ON specification is displayed.
Sound pressure: 80 dB min./87 dB average (Measured at 10 cm from front panel.)
Enabled/disabled (NT2000M only): The buzzer sound can be enabled or disabled by means of a setting pin. If it is disabled, the buzzer will not sound under any conditions.
Self-test for memory, switches, etc.
Status setting confirmation for communications and other conditions.
Simple communications confirmation.
Data backed up by lithium battery when screen data memory is SRAM.
Data backup time: 5 years (at 25 ° C)
If there is a voltage drop, the BAT LOW indicator on the front panel will light and the
Battery Low Flag to the host will turn ON.
The battery can be replaced from the rear of the Terminal while power is on.
If Key Input Sound is set to ON in the Memory Switch Menu, a beep will sound for 0.2 s when a system key, function key, or touch switch is pressed.
77
A abbreviations, 3 alarms, controlling from host, 43
ALM OUTPUT terminals, 25
ASCII Unit, 6, 7
B backlight, controlling from host, 42 bar graphs, displaying, 41 battery, replacing, 69 buzzer, controlling from host, 43
C cable, 73 child screens, 37, 38 communications, setting for NT20-LK201/LK203-E, 14 communications errors, automatic reset setting, 14 contract control, 9 control panel, specifications, 76 cover, 73
D data transfer, PT to host, 46 dimensions, 17
DIP switch, 9 display attributes, 36 capacity, 76 character scale, 36 characters, 36 data quanitities, 77
LCD check, 58 positioning, 36 specifications, 76 display history, 53 controlling from host, 43 initializing, 60
E error messages, 32
Index
F function key input screen, 47 function keys, checking, 56
H host computer controlling PT operation, 42 data transfer, 39, 40, 41, 44, 46, 47
Host Interface Units, displaying settings, 58
Host Link Unit, interface, 7, 8
HOST RUN INPUT controlling from host, 43 enable/disable setting, 14
HOST RUN INPUT terminals, 24
I
I/O checks, 56 initialization, 60 memory, 30 installation environment, 16 mounting position, 16 panel mounting, 18
K
Key Sheets, 73
L lamps attributes, 41 displaying, 41 language, setting, 14
LG and GR terminals, 23
M
Maintenance Mode, 53 maintenence, inspection, 71 memory, initializing, 30 memory capacity, 5 memory chips, 5 memory switch settings, 15
79
menus overview, 31 selecting items, 31 system menu, 52 mode changes, enable/disable setting, 14 models, 4
N nomenclature, 8 numeral table, 39, 41, 47 numeric display, 39 numeric settings, 47
P parent screens, 37, 38 power supply
24-VDC input terminals, 22
AC input terminals, 23 wiring, 22
PT settings, displaying, 58
R
RS-232C connector, 9
RS-232C interface, 6 connector, 26
RS-422 interface, 7
Index
S screen memory, initializing, 60 screens changing, 36 continuous screens, 37 examples, 36 maximum limit, 5 overlapping screens, 38 transferring online, 64 setting, defaults, 33 specifications, 75 special features, 77 string table, 40
Support Tool, 6 checking interface, 57
Support Tools, data transfer, 32 switch inputs, transferring to host, 46
SYSMAC BUS, interface, 7 system configuration, 6 system keys, 31
System Menu, 53
System ROM, selecting, 5
T terminology, 3 text strings, displaying, 40 touch switches, 46
Transmit Mode, 53 troubleshooting, 68
W wiring
ALM OUTPUT terminals, 25
HOST RUN INPUT terminals, 24
LR and GR terminals, 23 power supply, 22
RS-232C connector, 26 terminal block, 21
80
Revision History
A manual revision code appears as a suffix to the catalog number on the front cover of the manual.
Cat. No. V001–E1–2
Revision code
The following table outlines the changes made to the manual during each revision. Page numbers refer to the previous version.
Revision code
1
1A
2
Date
November 1991
October 1992
September 1993
Revised content
Original production
Page 3: A row defining the C200H has been added to the SYSMAC terminology table.
Manual numbers have been changed in the Reference Manuals table.
Page 4: The numbers of registered screens have been changed in the Memory Capacity and Number of Screens table. The model legend for the system ROM has been changed to incorporate the C200H. A model number for the Host Interface Units has been added to the table.
Page 5: C200H Interface has been added to the list of allowable interfaces for communications in 1-4-2 Operation.
Page 7: A C200H Interface description has been added.
Page 10: “Transfer Mode” has been changed to “Transmit Mode” for pin 6 of the switch settings table.
Page 11: SW1 has been changed to SW3 in the table.
Page 23: “Transfer Mode” has been changed to “Transmit Mode” within the procedure.
Page 26: The description within 4-1-3 Character Scale has been changed.
Page 32: NT20M-LB121-EV1 Host Interface Unit has been added to the Note at the bottom of the page.
Page 49: A description for the C200H Host Interface Units (NT20M-LB121-EV1) has been added.
Page 51: A description for the C200H Host Interface Units (NT20M-RT121-EV1) has been added.
Page 59: A row for the C200H Host Interface Units has been added to the table.
Page 2: A general introduction was added, describing the basic functions of PTs.
Pages 2 and 3: Some new features were added.
Page 4: Descriptions of NT20M and NT2000M PTs were added.
Page 5: Information was added about selecting System ROM.
Page 6: Information was added about the Support Tool.
Pages 7 and 8: Changes were made to system configuration illustrations.
Pages 9 to 12: Illustrations were added showing features and components of PT.
Page 14: Revisions were made to DIP switch settings.
Page 15: Revisions were made to memory settings.
Pages 15 to 20: NT2000M installation information was added.
Pages 21 to 27: NT2000M wiring and connector information was added.
Pages 30 to 31: Information was added concerning powering up and initializing the memory.
Pages 36 to 44: Information was added regarding NT2000M display functions.
Pages 48 to 50: Information was added regarding numeric input.
Page 52: Changes were made to menu illustration.
Pages 53 to 59: Changes were made to information regarding Maintenance Mode.
Pages 64 to 69: Changes were made and information was added regarding maintenance and inspection procedures.
Appendix A: Changes made to optional items.
Appendix B: Changes made to specifications.
81
OMRON Corporation
Control Devices Division H.Q.
Shiokoji Horikawa, Shimogyo-ku,
Kyoto, 600-8530 Japan
Tel: (81)75-344-7109/Fax: (81)75-344-7149
Regional Headquarters
OMRON EUROPE B.V.
Wegalaan 67-69, NL-2132 JD Hoofddorp
The Netherlands
Tel: (31)2356-81-300/Fax: (31)2356-81-388
OMRON ELECTRONICS LLC
1 East Commerce Drive, Schaumburg, IL 60173
U.S.A.
Tel: (1)847-843-7900/Fax: (1)847-843-8568
OMRON ASIA PACIFIC PTE. LTD.
83 Clemenceau Avenue,
#11-01, UE Square,
Singapore 239920
Tel: (65)6835-3011/Fax: (65)6835-2711
OMRON (CHINA) CO., LTD.
Room 2211, Bank of China Tower,
200 Yin Cheng Zhong Road,
PuDong New Area, Shanghai, 200120 China
Tel: (86)21-5037-2222/Fax: (86)21-5037-2200
Authorized Distributor:
Cat. No. V001-E1-2 Note: Specifications subject to change without notice.
Printed in Japan
0993-1.4M (1191)
Download
Advertisement