Mitsubishi Electric MR-E55R-PS-C Service Manual
Oglas
Oglas
HOME REFRIGERATOR
No. OAH110
SERVICE MANUAL
Models
MR-E55R-F-C
MR-E55R-PS-C
MR-E60R-F-C
MR-E60R-PS-C
Model name indication
(Inside this door)
CONTENTS
1. SPECIFICATIONS ••••••••••••••••••••••••••••••••••••••••••••••••••••••••••2
2. WIRING DIAGRAM ••••••••••••••••••••••••••••••••••••••••••••••••••••••••5
3. OUTLINES AND DIMENSIONS •••••••••••••••••••••••••••••••••••••••••7
4. REFRIGERANT CIRCUIT ••••••••••••••••••••••••••••••••••••••••••••••••9
5. TROUBLESHOOTING••••••••••••••••••••••••••••••••••••••••••••••••••• 10
5-1 FUNCTION OF OPERATION PANEL ••••••••••••••••••••••••••• 10
5-2 FLOWCHART OF SELF-CHECK •••••••••••••••••••••••••••••••• 22
5-3 BLOCK DIAGRAM OF PRINTED CIRCUIT BOARD •••••••• 26
5-4 AUTO ICE MAKER ••••••••••••••••••••••••••••••••••••••••••••••••• 26
5-5 FLOWCHART OF TROUBLE CRITERION •••••••••••••••••••• 28
5-6 TROUBLE CRITERION OF MAIN PARTS ••••••••••••••••••••• 35
5-7 TEST POINT DIAGRAM OF FILTER BOARD •••••••••••••••• 42
5-8 TEST POINT DIAGRAM OF CONTROL BOARD •••••••••••• 42
C •••• Taiwan
6. NAMES OF THE PARTS ••••••••••••••••••••••••••••••••••••••••••••••• 47
7. DISASSEMBLY INSTRUCTIONS ••••••••••••••••••••••••••••••••••••• 48
PARTS CATALOG (OAB110)
NOTE:
• RoHS compliant products have <G> mark on the spec name plate.
1
SPECIFICATIONS
SPECIFICATIONS
MR-E55R-C
MR-E60R-C
Power supply
L mm
V,Hz
Total capacity
Dimensions (H × W × D)
Cabinet
Food liner
Insulation
Cabinet
Freezer door
Refrigerator door
Cooling system
Freezer
Refrigerator
Evaporator
Condenser
Defrost system
Drain
Temperature control system
Refrigerator compartment interior light
Accessories
Weight
Unit
Shipping
Capillary tube
Desiccant (molecular sieve)
Refrigerant filling capacity R600a
Refrigerating oil (model) kg kg mm g g g
E55R E60R
110 V, 60 Hz
545 (gross)
1821 × 685 × 728
601 (gross)
1821 × 745 × 728
Acrylic resin coated steel
ABS resin
Foamed polyurethane (Cyclopentane)
Foamed polyurethane (Cyclopentane)
Foamed polyurethane (Cyclopentane)
Forced air convection
Forced air convection
Fin and tube type
Cabinet, cabinet ceiling, sides, back, front flange and machine chamber condenser
Cabinet, cabinet ceiling, sides, back and front flange
Automatic heater defrost
Automatic drainage, Forced evaporation method
Automatic control
LED
Change pocket (large)
Change pocket (small)
Bottle pocket (large)
Bottle pocket (small)
AUTO-shelf
Two-way flexishelf
Small item case
Free egg shelf
Slide chilled case
Lid of slide chilled case
Versa case
Aluminum tray (Versa case)
Water tank (with light-type bacteria removing filter with lead elimination function)
Freezing case (top)
Freezing case (bottom)
Ice server
Soundproof mat
Ice storage box
Vegetable case
Sliding case (Vegetable case)
Leg cover
103 108
2pcs.
2pcs.
1pc.
1pc.
2pcs.
1pc.
1pc.
1pc.
1pc.
1pc.
1pc.
1pc.
1pc.
1pc.
1pc.
1pc.
1pc.
1pc.
1pc.
1pc.
1pc.
109 115
1.6 × 0.63 × 2740, 1.8 × 0.67 × 2740
9
94
187 (FREOL S10)
2
ELECTRICAL PARTS SPECIFICATIONS
MR-E55R-C
Compressor
Motor protector
Three-way valve
Defrosting timer
Model
Power supply
Rated input
Starting current
W
A
Running current A
Winding resistance (A.T.20 )
Model
Ambient temperature
Time
Current
Model
Sec.
A
Type
Model
Specification
Heater
Defrost finish
Freezer compartment
Thermal fuse
Defrost heater 1
Defrost heater 2
Deodorizing function of defrost heater
Model
Type
Refrigerator Input
Revolution
Number of poles
Machine chamber
W rpm
Model
Input
Revolution
Number of poles
W rpm
Water pipe heater
Rotational heater board
Vegetable compartment heater
(Rating)
Ice making tray heater
Water tank heater
Model
Dial position
HI
MID
LOW
LOW (Soft freezing)
MID (Soft freezing)
HI (Soft freezing)
FREEZER(LOW)
FREEZER(MID)
FREEZER(HI)
ICE MAKING
ICE MAKING STOP
CRYSTAL ICE MAKING
EFI100E 13DHH
110 V, 60Hz
45 (1620rpm)
4 (Current limiter)
0.69 (1620rpm)
12.4
MM3-71CCV
25
16 or less
17.0
NSCE001DC1
4-phase stepping motor drive voltage DC12V
Control board
Microcomputer
Thermistor 14 ± 1.5
70 ± 2
81 (110V,150W)
141 (110V,86W)
Not equipped
UDQM002B3
DC brushless motor
2.4 (12V DC)
1520 (12V DC)
10P
4715JL04WS16G51
1.4 (12V DC)
1450 (12V DC)
4P
110V-4.0W
110V-8.0W
110V-7.3W
110V -12.1W
110V-4.0W
–
–
–
–
Freezer
Compressor
ON
− 22.2
− 18.9
− 14.3
–
–
–
–
–
–
–
OFF
− 23.8
− 20.6
− 16.0
–
–
–
–
–
–
–
OPEN
1.9
5.1
8.4
–
–
–
–
–
–
–
–
–
Refrigerator
SHUT
0.1
3.2
6.4
–
–
–
–
–
–
–
–
–
NTC thermistor
Versa
Motor damper
OPEN
–
SHUT
–
–
–
−
5.9
− 9.8
− 11.1
− 12.0
− 16.1
−
17.7
–
–
–
–
–
−
7.1
− 11.1
− 12.3
− 15.1
− 19.4
−
21.2
–
–
–
Ice making
OPEN
–
–
–
–
–
–
–
–
–
− 21.6
− 21.6
− 21.6
SHUT
–
–
–
–
–
–
–
–
–
− 23.4
− 23.4
− 23.4
–
–
–
–
–
–
–
–
–
Vegetable
Heater
OFF
4.2
6.1
7.7
ON
2.9
4.8
6.4
–
–
–
–
–
–
–
–
–
3
ELECTRICAL PARTS SPECIFICATIONS
MR-E60R-C
Compressor
Motor protector
Three-way valve
Defrosting timer
Model
Power supply
Rated input
Starting current
W
A
Running current A
Winding resistance (A.T.20 )
Model
Ambient temperature
Time
Current
Model
Sec.
A
Type
Model
Specification
Heater
Defrost finish
Freezer compartment
Thermal fuse
Defrost heater 1
Defrost heater 2
Deodorizing function of defrost heater
Model
Type
Refrigerator Input
Revolution
Number of poles
W rpm
Machine chamber
Model
Input
Revolution
Number of poles
W rpm
Water pipe heater
Rotational heater board
Vegetable compartment heater
(Rating)
Ice making tray heater
Water tank heater
Model
Dial position
HI
MID
LOW
LOW (Soft freezing)
MID (Soft freezing)
HI (Soft freezing)
FREEZER (LOW)
FREEZER (MID)
FREEZER (HI)
ICE MAKING
ICE MAKING STOP
CRYSTAL ICE MAKING
EFI100E 13DHH
110 V, 60Hz
45 (1620rpm)
4 (Current limiter)
0.69 (1620rpm)
12.4
MM3-71CCV
25
16 or less
17.0
NSCE001DC1
4-phase stepping motor drive voltage DC12V
Control board
Microcomputer
Thermistor 14 ± 1.5
70 ± 2
81 Ω (110V, 150W)
141 Ω (110V, 86W)
Not equipped
UDQM002B3
DC brushless motor
2.4 (12V DC)
1520 (12V DC)
10P
4715JL04WS16G51
1.4 (12V DC)
1450 (12V DC)
4P
110V-4.0W
110V-8.0W
110V-7.3W
110V-12.1W
110V-4.0W
–
–
–
–
Freezer
Compressor
ON
−
21.9
− 19.2
− 13.7
−
−
−
OFF
23.5
20.8
15.4
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
OPEN
0.7
3.8
7.0
–
–
Refrigerator
–
–
–
–
–
–
–
SHUT
−
1.2
1.9
5.1
–
–
NTC thermistor
Versa
Motor damper
OPEN SHUT
–
–
–
−
7.1
− 9.5
−
10.7
− 11.4
− 16.5
−
18.0
–
–
–
–
–
–
−
8.3
− 10.7
−
12.0
− 14.5
− 19.7
−
21.5
–
–
–
Ice making
OPEN
–
–
–
–
–
–
–
–
–
− 17.9
−
17.9
− 17.9
SHUT
–
–
–
–
–
–
–
–
–
− 20.8
−
20.8
− 20.8
–
–
–
–
–
–
–
Vegetable
Heater
OFF ON
7.0
9.0
10.7
–
–
5.1
7.0
8.7
–
–
–
–
–
–
–
–
–
4
2 WIRING DIAGRAM
MR-E55R-C
MR-E60R-C
VALVE MOTOR
M
ICE GEAR BOX
M
TEMP. CONTROL BOARD
(ON DISPLAY PANEL)
( SKELETON WIRING DIAGRAM )
The wiring diagram in the dashed line is the same as the one attached to the products.
THERMOPILE
MOTOR DAMPER
RI
MOTOR DAMPER
VS
INVERTER
LIGHT BROWN
CONTROL BOARD,N/F BOARD
YELLOW GREEN LIGHT BROWN
F1 : 10A FUSE
FUSE3: 3A FUSE
ON THE BOARD
BRIGHT YELLOW
LIGHT GREEN LIGHT GREEN LIGHT BROWN
DEFROST HEA
DEFROST HEA
LIGHT GREEN
M M M
M
PLUG
V
MS
3 ˜
U W
COMPRESSOR
*WHEN THE DOORS ARE CLOSED.
Although the following parts are called in different names here, they are identical with the parts shown in the service manual.
I.THERMISTOR (Ice making compartment thermistor)
V.THERMISTOR (Vegetable compartment thermistor)
VERSA.THERMISTOR (Versa compartment thermistor)
DEF.THERMISTOR (Defrost thermistor)
ICE-TRAY THERMISTOR (Ice making tray thermistor)
F.THERMISTOR (Freezer compartment thermistor)
R.THERMISTOR (Refrigerator compartment thermistor)
TEMP. CONTROL BOARD: (Operation P.C. board)
COMPENSATIONAL HEATER FOR VEGETABLE ROOM: (Vegetable compartment heater)
DIVIDER HEATER: (Rotational heater board)
LED BOARD IN VEGETABLE ROOM: LEDs (Vegetable compartment)
TANK LED: (LED for bacteria removal from water tank)
LED BOARD IN REFRIGERATOR ROOM (R): Interior LED (right)
LED BOARD IN REFRIGERATOR ROOM (L): Interior LED (left)
S.LED: Versa compartment supercool freezing LED
R.LED(D): Refrigerator deodorization LED
DOOR SW. (FOR R-COMPARTMENT & ICE ROOM): Door switch (for refrigerator compartment, ice compartment)
DOOR SW. (FOR F-COMPARTMENT): Door switch (for freezer compartment)
FAN MOTOR (FOR COMPRESSOR): (BOX FAN)
VALVE MOTOR: Three-way valve
MOTOR DAMPER VS: Motor damper (for vegetable/versa compartment)
MOTOR DAMPER RI: Motor damper (for refrigerator/ice making compartment)
5
MR-E55R-C
MR-E60R-C
VEGETABLE COMPRATMENT DOOR
( ACTUAL WIRING DIAGRAM )
FREEZR COMPARTMENT DOOR
ICE/ VERSA
COMPARTMENT DOOR
REFRIGERATOR
COMPARTMENT DOOR
1 WHITE
2
3 WHITE
WHITE
RED
YELLOW
BLUE
WHITE
WHITE
LIGHT BROWN
RED
SKY BLUE
BLUE
LIGHT GREEN
SKY BLUE
TEMP.
CONTROL BOARD
WHITE/ RED
LIGHT BROWN
BLACK
WHITE
BLUE
RED
YELLOW
BRIGHT YELLOW
PINK
LIGHT GREEN
ORANGE
GRAY
SKY BULE
LIGHT GREEN
VIOLET
LIGHT BROWN
RED
GRAY
YELLOW
BLUE
BLACK
ORANGE
LIGHT GREEN
VIOLET
RED
BLACK
LIGHT GREEN
BLUE
WHITE
ORANGE
YELLOW
WHITE
GRAY
RED
WHITE
BLACK
LIGHT BROWN
YELLOW
BRIGHT YELLOW
RED
LIGHT BROWN
GRAY
PINK
WHITE
WHITE/ RED
BROWN
BLUE
YELLOW GREEN
BLACK
BLACK
VIOLET
BRIGHT YELLOW
YELLOW
BLUE
WHITE/ RED
ORANGE
RED
BROWN
GRAY
YELLOW GREEN
PINK
WHITE
WHITE
VIOLET
YELLOW
BLACK
BLACK
WHITE
BLACK
VIOLET
WHITE
WHITE
2 1
WHITE
GRAY
SKY BULE
BLUE
RED
SKY BULE
ORANGE
WHITE/ RED
RED
BLUE
WHITE
GRAY
WHITE
WHITE
WHITE
WHITE
YELLOW
WHITE
RED
BLUE
BRIGHT YELLOW
BLACK
YELLOW
VIOLET
BRIGHT YELLOW
YELLOW GREEN
GRAY
SKY BULE
PINK
BROWN
BRIGHT YELLOW
YELLOW GREEN
LIGHT BROWN
WHITE
VIOLET
SKY BULE
YELLOW
GRAY
RED
BLACK
BRIGHT YELLOW
PINK
YELLOW
VIOLET
WHITE
YELLOW
WHITE
WHITE
RED
BLUE
BRIGHT YELLOW
LIGHT GREEN
LIGHT BROWN
WHITE
VIOLET
SKY BULE
YELLOW
GRAY
RED
BLACK
ORANGE
BLACK
LIGHT GREEN
VIOLET
YELLOW
BLACK
WHITE
RED
WHITE
RED
BLACK
BLUE
YELLOW
VIOLET
RED
GRAY
BRIGHT YELLOW
LIGHT GREEN
LIGHT BROWN
WHITE
VIOLET
SKY BLUE
YELLOW
GRAY
RED
BLACK
BRIGHT YELLOW
BLACK
RED
YELLOW
LIGHT BROWN
BLACK
VIOLET
LIGHT BROWN
VIOLET /BLACK
BLACK
YELLOW
BLACK
RED
BLACK
BRIGHT
YELLOW
1
4
2
3
BLACK
BLACK
BLACK
BLACK
3
4
2
1 YELLOW
WHITE
RED
BLUE
I.THERMISTOR (Ice making compartment thermistor)
VERSA.THERMISTOR (Versa compartment thermistor)
ICE-TRAY THERMISTOR (Ice making tray thermistor)
R.THERMISTOR (Refrigerator compartment thermistor)
V.HEATER (Vegetable compartment heater)
VEGETABLE LED: LEDs (Vegetable compartment)
R/I ROOM DOOR SWITCH: Door switch (for vegetable compartment, ice compartment)
FREEZER ROOM DOOR SWITCH: Door switch (for freezer compartment)
FAN MOTOR (FOR COMPRESSOR): (BOX FAN)
R.LED(L): Interior LED (left)
R.LED(D): Refrigerator deodorization LED
MOVE EYE MOTOR: i-see sensor
V.THERMISTOR (Vegetable compartment thermistor)
DEF.THERMISTOR (Defrost thermistor)
F.THERMISTOR (Freezer compartment thermistor)
TEMP. CONTROL BOARD: (Operation P.C. board)
DIVIDER HEATER: (Rotational heater board)
TANK LED: (LED for bacteria removal from water tank)
R.LED(R): Interior LED (right)
S.LED: Versa compartment supercool freezing LED
VALVE MOTOR: Three-way valve
( When the doors are closed. )
6
3
OUTLINES AND DIMENSIONS
MR-E55R-C
685(Display)
680(Cabinet)
6
283.5
394.5
358.8
348
358.5
318
249
400
406
413
337
436
283.5
6
394.5
245
393
408
578(Pitch between the rear wheels)
631(Pitch between the adjust bolts)
666(Pitch between the front wheels)
75 10
728(Display)
633 10
Unit : mm
255
596
655 37
203
595
581
595
595
314
307
196
541
539
547
541
204
REQUIRED SPACE FOR INSTALLATION
20 685 20
DOOR DIMENSION
R(L) R(R) I S F
Hight 822 822 212 212 363
Width 283.5 394.5 283.5 394.5
684
V
363
684
7
211 290
728
R(L) : Refrigerator compartment (Left)
R(R) : Refrigerator compartment (Right)
I : Ice making compartment
S : Select compartment [Versa compartment]
Freezer
MR-E60R-C
745(Display)
740(Cabinet)
6
283.5
454.5
75 10
728(Display)
633 10
358.5
348
358.5
318
249
400
406
413
245
393
337
436
408
283.5
6
454.5
255
638(Pitch between the rear wheels)
691(Pitch between the adjust bolts)
726(Pitch between the front wheels)
596
655 37
655
641
655
203
655
374
367
196
601
599
607
601
204
REQUIRED SPACE FOR INSTALLATION
20 745 20
DOOR DIMENSION
R(L) R(R) I S F
Hight 822 822 212 212 363
Width 283.5 454.4 283.5 454.5
744
V
363
744
211 335
728
R(L) : Refrigerator compartment (Left)
R(R) : Refrigerator compartment (Right)
I : Ice making compartment
S : Select compartment [Versa compartment]
F : Freezer compartment
V : Vegetable compartment
8
4 REFRIGERANT CIRCUIT
MR-E55R-C
MR-E60R-C
Condenser
Muffler
Evaporator
Dryer
#150
Cabinet pipe
Suction pipe
Capillary tube
1.6× 0.63×2740(mm)
Capillary tube
1.8× 0.67×2740 (mm)
Charge pipe
(Low pressure
side) 6.35
Compressor
Charge pipe
(High pressure side)
4.0
Three-way valve
9
5
TROUBLESHOOTING
5-1 FUNCTION OF OPERATION PANEL
MR-E55R-C
MR-E60R-C
(1) Function of normal operation
USEFUL FUNCTIONS
1
Child lock
Press and simultaneously for 3 seconds.
( lamp turns on)
Stop ice making
2
Press several times until is displayed.
ICE SELECT button
Pressing this button selects the setting of the ice making compartment.
Supercool freezing button
The supercool freezing operation starts.
This operation starts only when the room selection is set to the versa compartment, and also the versa compartment is set to soft freezing mode.
The supercool freezing operation ends automatically
• The supercool freezing operation automatically ends
after 6 to 8 hours.
When stopping the supercool freezing operation before it automatically ends
• Press once.
SELECT / QUICK button
Pressing this button sets each compartment’s temperature.
In order to cool fast:
Press for 3 seconds.
When the versa compartment is set at soft freezing
mode, fast cooling cannot be selected.
QUICK mode stops automatically
• QUICK mode automatically stops in 2 hours.
When stopping QUICK mode before it automatically ends
• Press once.
ROOM button
Pressing this button selects the compartment to be displayed.
Press to select the compartment before adjusting the temperature or cooling fast.
ECO mode (To start and cancel)
3
Press button for 3 seconds.
( lamp turns on)
Operating mode and Temperature range
Compartment
Refrigerator compartment
Versa compartment
Ice making compartment
Vegetable compartment
Freezer compartment
Mode Temp. range
Approx. 0 to 6°C
Approx.
− 9 to − 5°C
Approx.
− 18 to − 12°C
Approx.
− 21 to − 17°C
Approx.
− 21 to − 17°C
Approx.
− 21 to − 17°C
Approx. 3 to 9°C
Approx.
− 21 to − 17°C
To reset the settings when initialled, press and simultaneously for 3 seconds. The temperatures of the refrigerator, vegetable, and freezer compartments will be set to “Middle” .The Fast Cooling operations in all the compartments will stop.
· The display extinguishes in 30 seconds after the last button is pressed.
(No failure in refrigerator)
· Pushing any button turns on the display again.
The temp. range is based on the data measured at the center of each compartment with the door closed and with no food inside under the condition of ambient temperature 30°C.
10
(2) Demonstration mode for shop display
Setting
Within 1 minute after power supply turns on, press the
with the door of the ice making compartment opened.
, , and simultaneously for 5 seconds
When the setting is complete, a “beep” sound is heard and “Auto Demo Mode” is displayed.
Demonstration mode is not available when the temperature of freezer compartment is –7°C or lower.
Panel operation mode during demonstration mode
The panel operation mode changes to “manual” if any of the switches is pressed. It changes to "auto" if none of the switches
is pressed for 45 seconds since the last time any of the switches was pressed.
Manual mode: Panel indication changes according to switch operation.
Auto mode: Panel indication is automatically changed.
Release
1) Open the ice making compartment’s door during demonstration mode, and leave it open.
3) Simultaneously press , , and for 5 seconds. (A “beep” sound is heard in about 5 seconds.)
Verify that the room display and the temperature adjustment display on the operation panel do not light by turns a minute
after the 3 steps above are performed.
Note: Follow the procedure above to release demonstration mode as it cannot be released by simply turning on/off the power supply.
(3) Fine adjustment of temperature
Fine adjustment of temperature is available for refrigerator compartment, freezer compartment and versa
compartment.
As for versa compartment, however, it is only available when the compartment is set to
Setting
.
Simultaneously press and for about 3 seconds until a “beep” sound is heard.
Room display blinks every 10 seconds in fine adjustment mode.
Fine adjustments of temperature
Follow the same operation procedure for temperature adjustment.
Fine adjustment of temperature
Normal mode Fine adjustment mode
Note: -25 °C freezing.
S e l e c t t h e m a x i m u m s e t t i n g o f t h e temperature adjustment function for the freezer compartment.
There is no particular display when the setting is selected.
Release
Follow the same procedure as Setting and the finely-adjusted
temperatures are reset for refrigerator compartment, freezer
compartment and versa compartment at once.
Temperature is adjusted in approximately 0.3 to 0.6°C increments.
(5) “LOW” setting on the anti-condensation heater
Outline
This setting lowers energy on the anti-condensation heater, allowing for lower power consumption.
If, however, the condensation forms on the partitions, cancel the setting.
Setting
(4) Ice making test/Self-check
Setting
Press for about 5 seconds.
Operation and its display
While automatic ice making is testing, the indication of ice making compartment setting blinks on display.
When something is faulty, the error code is indicated.
Release
The test automatically finishes in 10 minutes.
Press and buttons simultaneously for 3 seconds
(until 1 beep sound is heard ).
Cancellation
Go through the same procedure as that of Setting (2 beep sounds are heard when cancelled).
When the settings are reset, this setting is also cancelled.
Display/indication of the setting status
No display is available to show the low setting state on the anti-condensation heater.
The number of beep sounds indicates the setting state.
Beep (1 time) Set to Low
Beep beep (2 times) Low setting is canceled and returned to normal state.
11
(6) Service Check Function
1) Outline
• The chart below shows the outline of service check function.
• “Service check entry” needs to be set in order to perform each check mode. After setting “service check entry,” start the
setting operation of the check mode to be displayed.
• blinks while service check function is performed.
• The display of indicates which mode is in operation.
• When one of the check modes is in operation, other modes cannot be set. The mode in operation needs to be cancelled
before setting another mode.
Once each check mode starts, it continues operating even if the door gets closed.
(Open the door when releasing each mode.)
Refer to the next sections about the operation procedure and display of each check mode.
• In order to release “service check function entry,” follow the same procedure as setting operation during “service check
function entry” or each check mode.
Service check function entry
Setting / releasing method
Door Button operation
Open the ice making compartment’s door
Simultaneously press and for 3 seconds
Display
Blinking
Mode
1) Compressor’s rotational speed change mode
…The rotational speed of the compressor can be changed; The fan motor in machine chamber can be switched on and off.
Door
Setting method
Button operation
Leave the
ice making
compartment’s
door open
Press for
3 seconds
2) Damper Operation mode
…Each damper can be opened and closed; Refrigerator fan can be switched on/off.
Leave the
ice making
compartment’s
door open
Simultaneously press
and for
3 seconds
Display
Lighting Blinking
(1)
(2)
3) Thermistor temperature check mode
…The detected temperature of each thermistor can be checked.
Leave the
ice making
compartment’s
door open
Press for
3 seconds
4) Error history display mode
…The error occurred in the past can be checked.
Leave the
ice making
compartment’s
door open
Simultaneously press
and for
3 seconds
(3)
(4)
(1) History display mode
…All the errors occurred in the past can be checked in numeric order.
-
Press
(1)
“History display mode” and “Order of occurrence mode” are switched over each time is pressed.
(4)
(2) Order of occurrence mode
…The newest 5 errors (at the maximum) are displayed from the newest to the older.
-
Press
(2) (4)
5) Set temperature adjustment mode
…The set temperature in each compartment can be
adjusted.
Leave the
ice making
compartment’s
door open
Simultaneously press
and for
3 seconds (5)
12
2) Compressor’s rotational speed change mode
Setting
With the ice making compartment’s door opened, simultaneously press sound is heard. starts to blink.
and for 3 seconds until a “beep”
With the door opened, press for 3 seconds to start compressor’s rotational speed change mode.
Once this mode starts, it continues operating even if the door is closed.
Compressor’s rotational speed change mode is not available during demonstration mode, thermistor temperature check
mode, set temperature adjustment mode, error history display mode, or when child lock is effective.
Display during compressor’s rotational speed change mode
During compressor’s rotational speed change mode, blinks and lights up.
Display of rotational speed
• Compressor’s rotational speed is divided into ones’ place and tens’ place when it is displayed.
• One of the values (8/4/2/1) is assigned to each indicator of both tens’ place and one’ place on the display panel. The sum of
the corresponding values of the lighting indicators is the compressor’s rotational speed.
Fan in box fan ON/OFF
Blinking
Compressor’s rotational speed
Tens’ place
“ ”
Lighting
Compressor’s rotational speed
Ones’ place
Room display
Corresponding values
8
4
2
1
Ice making mode display e.g.) Compressor’s rotational speed 56rps, Fan box fan ON
Fan in box fan ON
Display during Compressor’s rotational speed change mode
Corresponding values
8
2
4
1
Blinking
Tens’ place "5"
(=4+1)
“ ”
Lighting
Ones’ place "6"
(=4+2)
Display during Compressor’ s rotational speed change mode
Changing the rotational speed
After setting this mode, compressor’s rotational speed changes every time button is pressed.
Rotational speed (rps) is divided into ones’ place and tens’ place when it is displayed.
(Basically the compressor starts operation at level 10, however, it may be different depending on models, or as a result of specification change.)
<Change of rotational speed>
Normal
Level 0
Low speed
Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 Level 7 Level 8 Level 9 Level 10
High speed
Rotational speed can be changed only when the compressor is in operation. While the compressor stops, rotational speed is
not displayed, and button operation is not effective. When the compressor stops, unplug the power code, and wait for
a several minutes, then plug it again.
Operation sound may get increase in the process of changing rotational speed, but that is not dysfunction. Check the sound
level when rotational speed is stabilized.
Switching ON/OFF the box fan
In this mode, box fan can be switched on and off at each press of .
The ON/OFF state is displayed with on the display panel.
Box fan
ON
OFF
Display of
Lighting
Not lighting
13
Release
With the ice making compartment’s door opened, press and sound is heard. The screen returns to the normal temperature display.
simultaneously for 3 seconds until a “beep”
The function is automatically released in one hour.
Although unplugging and plugging the power code can release this function, it is recommended to follow the procedure above for protection of the compressor.
3) Damper Operation Mode
Setting
With the ice compartment door opened, press
heard. blinks.
and simultaneously for 3 seconds until a “beep” sound is
With the door opened, press and simultaneously for 3 seconds until a “beep” sound is heard.
Damper operation mode starts. Once this mode starts, it continues operating even if the door gets closed.
Damper operation mode is not available during demonstration mode, thermistor temperature check mode, compressor’s rotational speed change mode, temperature adjustment mode, error history display mode, or when child lock is effective.
Display during damper operation mode
During damper operation mode, blinks and lights up.
Control state display of each damper
b) State of damper
: present state
: next state
( The damper of the selected compartment is in operation, the indicator
in the present state blinks.)
Blinking a) Damper “ ”
Lighting c) Refrigerator d) Display during damper
During damper operation mode a) Damper serial number
The room display on the display panel corresponds to the values representing damper types. The room display indicators
and their corresponding values (8/4/2/1) are shown in the tables below.
Each serial number is assigned to each compartment (thermistor), which is used in thermistor temperature mode and
set temperature adjustment mode besides damper operation mode. The sum of the corresponding values of the lighting
indicators is the damper’s serial number.
Room Display Corresponding values
8 4
2 1
Serial number
1
4
5
2
3
9
10
11
6
7
8
Assigned compartment
Refrigerator compartment
Slide chilled compartment
Ice making compartment
Versa compartment
Vegetable compartment
Freezer compartment
Defrosting
Ice tray
Outdoor air
Deodorization
Thermopile
/ : SW operation is effective/ineffective
Damper operation mode b) State of damper
on the left and operation.
on the right represent respectively the present state and the next state of the damper
When the right and left indicators are ON, it indicates that the damper is open.
When the right and left indicators are OFF, it indicates that the damper is close.
Present Next
c) ON/OFF state of refrigerator fan motor
indicates the ON/OFF state of refrigerator fan motor.
14
Opening and closing dampers
(1) Press to select the damper to be set. Each press of the button makes a “beep” sound and changes the kind of
dampers. The serial number described in a) indicates the selected damper.
The selected damper is displayed using the serial number (1: refrigerator ~ 10: deodorization) in numeric order repeatedly.
Refrigerator damper slide chilled compartment damper ice making compartment damper outdoor air deodorization damper
Slide chilled compartment, defrosting, ice tray, outdoor air, and deodorization can be selected;
however, it is ineffective in damper operation mode.
(2) To open the damper, turn on
Damper operation indicators
on the left and
, and to close the damper, turn off by pressing button.
on the right represent respectively the present state and the next state of the damper operation.
The on and off of the right and left indicators indicate respectively the opening and closing of the damper.
The damper operation of the indicator blinking in the “present state” is in operation.
When any of the damper operations including those not selected is in operation, blinks.
Present Next
The present and next damper operations of the selected
compartment illuminate.
When the damper of the selected compartment is in
operation, the indicator in the present state blinks.
<Present and next states of the damper of the selected
compartment>
Blinking
< The damper of any compartment is in operation>
(3) Press for 3 seconds to operate the damper. (A “beep” sound is heard when the setting has been conveyed.)
Setting of the operating damper cannot be changed.
Damper operation stops automatically. (Blinking changes to lighting.) e.g.) When changing the damper of ice making compartment from “CLOSE” state to “OPEN” state, select the indicators as shown below and press for 3 seconds.
b) State of damper
Present: “ ”
Next: “ ” a) Serial
number
“ ”
Lighting
“3” : Ice making compartment c) Refrigerator fan
Lighting: ON
Switching ON/OFF the refrigerator fan motor in the unit
In this mode, each press of switches on and off the refrigerator fan motor.
The ON/OFF state of the refrigerator fan motor is represented with .
display
Lighting
Not lighting
Fan motor in the unit
ON
OFF
Release
With the ice making compartment’s door opened, press heard. The screen returns to the normal temperature display.
and simultaneously for 3 seconds until a “beep” sound is
The function is automatically released in one hour.
Although unplugging and plugging the power code can release this function, it is recommended to follow the procedure
above for protection of the compressor.
15
4) Thermistor temperature check mode
Setting
With the ice compartment door opened, press
heard. blinks.
and simultaneously for 3 seconds until a “beep” sound is
With the door opened, press for 3 seconds.
Thermistor temperature check mode starts. Once this mode starts, it continues operating even if the door gets closed.
Thermistor temperature check mode is not available during demonstration mode, compressor's rotational speed change
mode, set temperature adjustment mode, error history display mode, or when child lock is effective.
Display during thermistor temperature check mode
During thermistor temperature check mode, blinks and lights up.
Displaying the thermistor temperature
The kind and temperature of thermistor is displayed on the operation panel.
The ambient temperature detected by thermistor may be a little different from the actual one due to the influence of the
temperature in the refrigerator.
b) Thermistor temperature c) Thermistor temperature signs
Blinking a) Thermistor “ ” “ ”
Lighting d) Thermistor
temperature
Display during thermistor temperature check mode a) Thermistor serial number
The room display on the display panel corresponds to the values representing thermistor types. The room display indicators
and their corresponding values (8/4/2/1) are shown in the tables below.
Each serial number is assigned to each compartment (thermistor), which is used in damper operation mode and
set temperature adjustment mode besides thermistor temperature mode. The sum of the corresponding values of the
lighting indicators is the thermistor’s serial number.
Room display
Corresponding values
8
4
2
1
Serial number
1
2
3
4
5
8
9
6
7
10
11
Assigned compartment
Refrigerator compartment
Slide chilled compartment
Ice making compartment
Versa compartment
Vegetable compartment
Freezer compartment
Defrosting
Ice tray
Outdoor air
Deodorization
Thermopile
/ : SW operation is effective/ineffective
Thermistor temperature check mode b) Thermistor temperature tens’ place
Usually, the , , and indicators that are used for temprature adjustment in the versa compartment represent
tens' place of the thermistor temprature.
Display of / / corresponds to the values, 4/2/1. The sum of the corresponding values of the blinking
indicators is the tens’ place of thermistor temperature.
Room display Corresponding values
4
2
1 c) Thermistor temperature signs
Plus and minus signs of thermistor temperature are indicated on the display which is usually used for mode.
Lighting
Not lighting
Thermistor temperature signs
-
+
16
d) Thermistor temperature ones’ place
Ones’ place of thermistor temperature is indicated on the display part which is usually used for ice making setting.
Display of / / / corresponds to the values, 8/4/2/1. The sum of the corresponding values of lighting
indicators is the ones’ place of thermistor temperature.
Room display
Corresponding values
8
4
2
1 e.g.) When freezer compartment thermistor is –25 ºC.
b) Tens’ place
“2” c) Sign
“-”
Blinking a) Serial number
“ ” “ ”
Lighting d) Ones’ place
“5” (=4+1)
Display during thermistor temperature check mode
Changing the thermistor on display
While thermistor temperature is on display, press .
Each press of the button makes a “beep” sound and changes the kind of thermistor.
Each thermistor is displayed using the serial numbers described in a) in numeric order repeatedly (1: refrigerator
compartment ~ 11: thermopile).
Refrigerator compartment slide chilled compartment ice making compartment versa compartment vegetable
compartment freezer compartment defrosting ice tray outdoor air deodorization thermopile
When this mode is set, the display always starts from the refrigerator thermistor.
Slide chilled compartment thermistor can be selected; however, it is ineffective because slide chilled compartment thermistor
is not installed.
Deodorization can be selected; however, it is ineffective in thermistor temperature check mode.
Release
With the ice making compartment’s door opened, press and
sound is heard. The screen returns to the normal temperature display.
simultaneously for 3 seconds until a “beep”
The function is automatically released in one hour.
Although unplugging and plugging the power code can release this function, it is recommended to follow the procedure
above for protection of the compressor.
17
5) Error history display mode
The errors occurred in the past can be observed as an error history. Use this mode when the actual problem of the refrigerator is different from the error that was displayed at the service-call received.
Error history display mode offers two ways of display. One of the two is “history display mode,” which shows all errors occurred in the past in numeric order of the error code; the other is “order of occurrence mode,” which shows the newest 5 errors (at the maximum) from the newest to the older.
Error history display mode starts with “history display mode.”
Setting
With the ice compartment’s door opened, press
heard. blinks.
and simultaneously for 3 seconds until a “beep” sound is
With the door opened, press and simultaneously for 3 seconds until a “beep” sound is heard.
History error mode starts. Once this mode starts, it continues operating even if a door gets opened.
Display during error history display mode
During error history display mode, blinks and lights up.
Display of error history information.
a) Mode display
Blinking b) Error code “ ”
Lighting c) Error code
Display during error history display mode a) Mode display
Display the selected mode between “history display mode” and “order of occurrence mode.” b) Error code tens’ place
It displays the tens’ place of error code.
It applies the same representative method as the error display of self-check.
c) Error code ones’ place
It displays the ones’ place of error code.
It applies the same representative method as the error display of self-check.
Switching over the mode
Press to select one of the error history display modes. Each press of the button makes a “beep” sound and
switches over between “history display mode” and “order of occurrence mode.”
Compartment Error history display mode
History display mode Display all errors occurred in the past in numeric order of the error code
Order of occurrence mode Display the newest 5 errors (at the maximum) from the newest to the older.
Display method
Display method of the error code is the same as self check error display. (Refer to 5-2(3)); however, all indicators used for
the display of error code light up simultaneously for 3 seconds before the first error code is displayed (“pre-display”).
e.g.) When errors occurred in the following order: fan motor error (
E31
) communication error of operation panel (
E01
) refrigerator thermistor error (
E13
)
• Display during history display mode
Errors are displayed in numeric order.
Tens’ place
Ones’ place
Error code Pre-display
0.5
sec.
3sec.
E01
5sec.
E13
0.5
sec.
Repetition
5sec.
18
0.5
sec.
E31
5sec.
0.5
sec.
Pre-display
3sec.
•Display during order of occurrence mode
Errors are displayed from the newest to the older.
Tens’ place
Ones’ place
Error code Pre-display
0.5
sec.
3sec.
E13
5sec.
E01
0.5
sec.
Repetition
5sec.
0.5
sec.
E31
5sec.
0.5
sec.
Pre-display
3sec.
When no error occurred in the past, error code is not displayed.
Check points and resetting the error history
Check and take appropriate measures according to the procedures as stated in 5-2(1).
Conduct self-check again to confirm there is no malfunction. (Make sure all connectors are connected properly and there is no loose connection.)
Refer to “ Setting ” above and activate the error history mode again. With the ice making compartment’s door opend,
press for 3 seconds to reset error history. (Resetting the error history is completed.) If it is completed correctly,
no error code would be displayed.
Release
With the ice making compartment’s door opened, press and
sound is heard. The screen returns to the normal temperature display.
simultaneously for 3 seconds until a “beep”
The function is automatically released in one hour.
Although unplugging and plugging the power code can release this function, it is recommended to follow the procedure
above for protection of the compressor.
6) Set temperature adjustment mode
Switch operation on the operation panel changes the set temperature in each compartment.
Setting
With the ice compartment door opened, press
blinks.
and simultaneously for 3 seconds until a “beep” sound is heard.
With the door opened, press and simultaneously for 3 seconds until a “beep” sound is heard.
Set temperature adjustment mode starts. Once this mode starts, it continues operating even if the door gets closed.
Display during set temperature adjustment mode
During set temperature adjustment mode, blinks and lights up.
Control state display of each compartment
b) Set temperature a) Compartment “ ” “ ”
Lighting
Blinking
Display during set temperature adjustment mode
19
a) Compartment serial number
Serial number of the selected compartment for set temperature adjustment is displayed on the part that are usually used
for room display.
Each serial number is assigned to each compartment that will be used in set temperature adjustment mode besides damper
operation mode and thermistor temperature check mode.
The sum of the corresponding values of the lighting indicators is the compartment serial number.
Room display
Corresponding values
8
4
2
1
Serial number
1
2
3
4
9
10
11
7
8
5
6
Assigned compartment
Refrigerator compartment
Slide chilled compartment
Ice making compartment
Versa compartment
Vegetable compartment
Freezer compartment
Defrosting
Ice tray
Outdoor air
Deodorization
Thermopile
/ : SW operation is effective/ineffective b) Set temperature adjustment level
Set temperature adjustment mode
Adjusting the set temperature
(1) Select the compartment with button.
(2) Each press of the button makes a “beep” sound and changes the compartment to adjust the set temperature.
Each compartment will be displayed using the serial numbers (1: Refrigerator compartment~ 6: Freezer compartment) in numeric order repeatedly.
Refrigerator compartment slide chilled compartment ice making compartment versa compartment
vegetable compartment freezer compartment
Set temperature adjustment operation of slide chilled compartment is possible; however, it is ineffective because slide chilled compartment thermistor is not installed.
(3) Select the adjustment level of set temperature with .
Each press of the button makes a “beep” sound and changes the adjustment level of set temperature.
There are 5 adjustment levels of set temperature ( 2 & 0), and the selected level is displayed.
The indicator that lights up represents minus ( − ).
Adjustment level Temperature adjustment display
+2
+1
±0
− 1
− 2
Change of the set temperature
About +2 ºC
About +1 ºC
No change
About − 1 ºC
About − 2 ºC
The changed adjustment levels are stored on the control board. If the control board is replaced, the updated information will be lost.
Release
With the ice making compartment’s door opened, press and
sound is heard. The screen returns to the normal temperature display.
simultaneously for 3 seconds until a “beep”
The function is automatically released in one hour.
Although unplugging and plugging the power code can release this function, it is recommended to follow the procedure
above for protection of the compressor.
20
Door Buzzer System :
Door buzzer has been installed so that one will not forget to close the door.
• The buzzer rings in the following conditions:
1. When door is left open.
2. When refrigerator fan motor or box fan is abnormal.
1. When door is left open
Every 1 minute, for 4 minutes
After 5 minutes
2. Refrigerator fan motor or box fan is abnormal
Buzzer
"Beep beep" 4 times
“"Beep beep" continuously
"Beep beep" 2 times
1. The buzzer rings to inform the open door when the door of ice making compartment, refrigerator compartment, or freezer
compartment is left open for more than 1 minute.
• The buzzer rings every minute. After 5 minutes, the buzzer rings continuously.
Blinks while • The buzzer will stop ringing as soon as the door is closed.
• When the buzzer does not stop even if all the doors are closed, the door switch may be abnormal.
interlocking with “beep, beep”
The buzzer can be stopped by the following operations.
Perform the ice making test operation. (Refer to 5-2(1).) tone.
(Note: If the test is conducted with water in the ice tray, water may fall into the ice storage box
because the tray is rolled over in the ice making operation.)
Synchronizing the buzzer sound, the indicator(s) of the compartment(s) with door(s) that are(is) left
open blink(s) to alert.
2. Buzzer sounds when a trouble is found in refrigerator fan motor or in box fan. The buzzer sounds
every time the door is closed until normal operation is obtained.
(Check the error code by following the steps in Specification of display in self-check result on page 22.)
Interior LED :
• Interior LED inside the refrigerator compartment lights when the door of refrigerator compartment or ice making compart-
ment is open.
• When interior LED is lighted continuously for more than 60 minutes, it is turned off to prevent heating.
• The protection is released when doors of refrigerator compartment and ice making compartment are closed. Then, interior
LED will be lighted the next time at normal timing.
21
5-2 FLOWCHART OF SELF-CHECK
MR-E55R-C
MR-E60R-C
(1) Troubleshooting with self-check
This refrigerator has self-check feature to clarify and indicate where & what the trouble is.
You can perform operation checks and identify malfunction of electric or electronic parts.
Error history is recorded and can be displayed by the refrigerator.
Self-check
Operate the ice-making test.
(Current displayed error: Refer to in the table below.)
The display of ice making compartment setting will blink during the test.
During the ice-making test mode, watch the operation ice-maker gear box and water pump in refrigerator.
Error history mode (Refer to 5-1.(6)5))
Problem may recover automatically.
Perform the following if error is not displayed before taking measures or the error which was informed from user by telephone is not displayed.
Is error displayed?
Yes
Locate the trouble according to error display. (See page 23-25)
No
Unplug the power cord from outlet.
Set the error display mode.
Is error displayed?
Yes
Perform self-check procedures through .
No
Release error displayed
mode, and the self-check
is finished.
Repair /replace defective part(s) according to error display.
Reset the error history.
(Refer to 5-1.(6)5))
Self-check
Plug the power cord into outlet.
(Current displayed error:
Refer to in the table below.)
*Wait 10 minutes
before plugging
the cord once
it's unplugged.
(If the cord is
plugged in within
10 minutes, error
may be displayed.)
Yes
Is error displayed?
No
Release error display
mode and perform the
self-check again.
(go to )
Yes
Is error displayed?
Note1: Self-check cannot detect abnormalities in the following parts.
See page 28-41 for troubleshooting.
No
Was more than one error displayed during repair?
Yes
No
Perform error history mode.
Heater (Water pipe/Vegetable compartment heater, etc.)
Water pump motor
Note2: If any abnormality is found when plugging the power cord, compressor and fan motor are suspended for 10 minutes.
Note3: The alarm beeps when some abnormalities (motor-locked) have occurred at the refrigerator fan motor or box fan restarts its normal
operation.
Note4: If any abnormality occurs in compressor's inverter circuit, the compressor and the refrigerator fan motor stop for 10 minutes
(not only when plugging the power cord).
Was the error which was informed from user by telephone displayed?
And were measures taken?
Yes
Self-check is finished.
No
Perform error history mode.
Self-check and error display method and operation
Item Operation method
Ice making test operation.
All items except (*6) listed up on the table at page
25 will be checked.
Press the switch.
for 5 seconds.
(“Beep” is heard)
Display or self-check operation
1.Conduct the automatic ice making test.
(The display of ice making compartment
setting blinks)
2.When trouble is found, all error codes
3.When error is not found, nothing is
displayed.
1.When trouble is found, all troubles except
E50 ~ E55 are displayed.
2.When error is not found, nothing is
displayed.
1.When trouble is found, all troubles except
E50 ~ E57 are displayed.
2.When error is not found, nothing is
displayed.
Display period
For 10 minutes after setting.
Others
Self-check is not available during child lock, cooking timer, changing the rotational speed of compressor, checking the temperature of thermistor, damper operation and demonstration modes.
Self-check is not available during demonstration mode.
Power input.
All items except (*6) listed up on the table at page
25 will be checked.
Error history
Plug the power cord into outlet.
Refer to 5-1.(6)5)
Error history display mode.
For 10 minutes after power is supplied.
For 1 hour after setting, or until mode is released.
Self-check is not available during child lock, cooking timer, changing the rotational speed of compressor, checking the temperature of thermistor, damper operation and demonstration modes.
Release of self-check display mode
Self-check finishes automatically. Error cord display is automatically released 10 minutes later.
22
(2) Timing in self-check
Trouble of Defrost heater : Self-check is conducted after defrosting.
(Make sure to confirm the display before unplugging the power cord
because it is automatically reset once the power cord is unplugged.)
Trouble of Ice maker
Trouble of Fan motor
Trouble of Inverter
Trouble of Thermistor
: Press the switch on the panel for 5 seconds. (Ice making test mode)
The setting of ice making compartment blinks on display during the test operation.
: Open the door and then close it.
When abnormality is found in fan motor, buzzer sound is heard every time the door is closed.
: Check the error when compressor starts up or is operating.
: Self-check is continuously working
(3) Error display and trouble locating
1. Display details
After conducting the self-check referring to 5-2(1), flashes repetitively and the error code will be displayed and divided into tens’ place and ones’ place if any.
When two or more errors occur, they are displayed alternately. The error whose code has smaller number has priority to be displayed first. There are 0.5 seconds intervals between the error codes
Flashing b) Error code
Tens’ place c) Error code
Ones’ place
Room display
Corresponding values
8
4
2
1
Ice making mode display Corresponding values
8 4
2 1 e.g.) In case the errors of refrigerator thermistor (
E13
) and ice maker gear box (
E33
) are occuring simultaneously.
Tens’ place
Ones’ place
Error code
E13 E33 E13 E33
0.5
sec.
0.5
sec.
0.5
sec.
5sec.
5sec.
5sec.
5sec.
For 2 minutes in self-check, a high-tone sound is heard due to the operation check of damper.
2. Check point and measures
Display
Error code
Display
Tens' place Ones' place
Testing (*1)
E 01
E 02
E 03
Trouble
Detecting method
(*3)
Check point Measures Control
(*4)
Communication error of operation panel
Ice maker is under testing
When the following communication errors occur between control board and operation P.C. board:
• They transmit and receive
data that has nothing to
do with settings.
• They cannot transmit
and receive data each
other for about 2 seconds.
1. Connector CN10K, CN9S, CN5D on control board
5-pin wire to wire connector (hinge)
5-pin connector on operation P.C. board
2. Trouble of control board and operation
P.C. board
Repair the contact failure.
Replace.
Keep the same operation as the one before the communication error has occurred.
Communication error of inverter
When abnormality is found in the communication between refrigerator control circuit and inverter control circuit in control board.
(When they do not transmit and receive data for 10 seconds.)
Trouble of model judgement
Replace the control board.
When the model of control board is different from that of operation
P.C. board.
1. Check the model name of control board. Replace.
2. Check the operation P.C. board.
Replace.
Compressor OFF.
Keep operating the unit, and conduct error code indication only.
E 10
E 11
E 12
Trouble of ice making tray thermistor
When there is a short or open circuit in the ice making tray thermistor.
1. Connector CN9S on control board, ice gear box 6-pin wire to wire connector, 8-pin wire to wire connector
Repair the contact failure.
Trouble of freezer compartment thermistor
Trouble of defrost thermistor
When there is a short or open circuit in the freezer compartment thermistor.
When there is a short or open circuit in the defrost thermistor.
2. Check the resistance of thermistor.
1. Connector CN9S on control board,
4-pin wire to wire connector
2. Check the resistance of thermistor.
1. Connector CN9S on control board,
2-pin wire to wire connector
2. Check the resistance of thermistor.
Replace.
Repair the contact failure.
Replace.
Repair the contact failure.
Replace.
When the compartment door has been closed for 3 hours and when freezer compartment thermistor is -10 or less, ice-detecting operation starts.
After 10 minutes off, the compressor repeats 30- minute ON and 20-minute
OFF.
The defrost heater won’t be turned ON.
23
Display
Error code
Display
Tens' place Ones' place
E 13
E 15
E 16
Trouble
Trouble of refrigerator thermistor
Trouble of versa compartment thermistor
Detecting method
(*3)
Check point
When there is a short or open circuit in the refrigerator compartment thermistor.
1. Connector CN9S on control board,
4-pin wire to wire connector
2. Check the resistance of thermistor.
When there is a short or open circuit in the versa compartment thermistor.
1. Connector CN9S on control board,
6-pin wire to wire connector
Trouble of vegetable compartment thermistor
When there is a short or open circuit in the vegetable compartment thermistor .
2. Check the resistance of thermistor.
1. Connector CN9S on control board, 2-pin wire to wire connector
2. Check the resistance of thermistor.
Measures
Repair the contact failure.
Replace.
Repair the contact failure.
Replace.
Repair the contact failure.
Replace.
Control
Synchronize the open/ close status of R damper with that of compressor
ON/OFF.
• When S-compartment is used as “freezer”:
S-damper is open when compressor is turned on, S-damper is closed when compressor is turned off.
• When S-compartment is used as other than
“freezer”: S-damper remains open for the first 3 minutes and then closed for the rest of time.
S-compartment: Versa
(select) compartment.
• When R-damper is open,
V-heater is turned on.
• When R-damper is closed, V-heater is turned off.
E 17
E 18
E 23
E 30
E 31
E 32
E 33
E 34
E 41
Trouble of ice making compartment thermistor
When there is a short or open circuit in the ice making compartment thermistor.
1. Connector CN9S on control board, 6-pin wire to wire connector
2. Check the resistance of thermistor.
Repair the contact failure.
Replace.
Trouble of outside air thermistor
Trouble of thermopile
Trouble of defrost heater 1
(*6)
When there is a short or open circuit in the outside air thermistor.
When there is a short or open circuit in the outside air thermistor.
When defrosting is not finished in 2 hours.
Relay connector 10 pin 2 positions.
Refer to "5-9.3 Failure diagnosis for the
thermopile (HIKARI i-see Sensor)".
1. Connector CN2A on control board,
Defrost heater plug and receptacle,
1-pin wire to wire connector,
Thermal fuse 4-pin wire to wire connector
Replace the operation
P.C. board.
Repair the contact failure.
Trouble of refrigerator fan motor
Trouble of box fan
2. Check the resistance of defrost heater. Replace.
3. Check the continuity of thermal fuse.
Replace.
• When motor doesn’ t rotate even though power is on.
• When the waveform, which indicates the rotation times of motor, cannot be detected.
1. Connector CN5D on control board,
Refrigerator fan motor 4-pin wire to wire connector
Repair the contact failure.
2. Check refrigerator fan motor operation. Replace.
• When motor doesn’ t rotate even though power is on.
• When the waveform, which indicates the rotation times of motor, cannot be detected.
1. Connector CN4D, CN5D on control board, Box fan, 4-pin wire to wire connector
2. Check box fan operation.
Repair the contact failure.
Replace.
• When ice making compartment is used as
“refrigerator”, synchronize
I-damper with R-damper.
• When ice making compartment is used as “ice making”, synchronize
I-damper with F-damper.
Compressor is activated at “Speed-level 2.”
Perform supercool freezing control in emergency operation mode.
The defrost heater is stopped and if the next defrosting finishes in 2 hours, the error code will disappear.
• 3 minutes later, the refrigerator fan motor is reactivated to be checked.
• Until the fan motor gets to operate correctly, the buzzer sounds every time the door is closed.
• 3 minutes later, the box fan is reactivated to be checked.
• Until the fan motor gets to operate correctly, the buzzer sounds every time the door is closed.
Trouble of ice maker gear box
When the gear box operation is not finished in 30 seconds.
Clogging of refrigerant pipe or trouble related to compressor
Trouble of solenoid three-way valve
1. Connector CN8K, CN10K on control board, ice gear box
6-pin wire to wire connector, 8-pin wire to wire connector
2. Ice gear box frozen point
3. Check the trouble of the ice gear box with the ice making test operation.
(T0: Defrost thermistor temperature at power input, T1: Defrost thermistor temperature when
15 minutes have passed from the power input)
•When the difference between
T0 and T1 is T0 T1. (*5)
Check the compressor and the pipe.
When defrost thermistor reads -10 or above in five minutes after the compressor’s startup. (*5)
Connector CN4D on control board,
5-pin connector to three-way valve
Repair the contact failure.
100 minutes later, the gear box is reactivated to be checked again.
Replace.
Replace.
Repair the contact failure.
When cooling operation returns to normal condition, the display of error code disappears.
Check the operation of solenoid three-way valve and then open the valve.
24
E 50
E 51
E 52
E 53
E 55
E 56
Display
Tens' place Ones' place
Trouble
Trouble of inverter circuit
Detecting method
(*3)
• When there is any trouble in the circuit which detects current of compressor.
Check point Measures
(*6)
Trouble of bus-bar voltage
(*6)
• When the range of busbar voltage is not approx.
50 ~ 380 V DC.
Trouble of inverter software reset function
• When the inverter driving software malfunctions.
(*6)
Trouble of startup, synchronization or overcurrent detection
(*6)
• When there is no current at compressor startup.
• When phase current exceeds 5.5A at compressor startup.
• When phase current exceeds 3.3A during compressor operation.
• When current of 5.3A or more runs into the busbar of control board.
Trouble of control board
(EEPROM
related trouble)
(*6)
EEPROM (IC11M) accumulates data necessary for control.
• When the data are not input accurately.
• When microcomputer cannot read the data.
Refer to “Compressor does not operate” at page 30.
Replace the control board.
Defective wiring connecting or trouble of control board
The errors E50 to E53 keep occurring over one and a half hour. (The situation, which compressor cannot be operated, continues.)
Refer to “Compressor does not operate” at page 31.
E 57
Inverter drive module abnormality
When the overcurrent error is detected before starting the compressor
(failure of the IC in the inverter drive module).
Control
The compressor is suspended and reactivated
10 minutes later.
Replace the control board.
When abnormality occurs in power input, the compressor is suspended for 10 minutes.
When abnormality occurs in normal operation, the compressor keeps operating.
• Error display starts after it is regarded as E56 .
• Error display continues until defrosting starts or cooling operation gets back to normal. (Error display doesn’t disappear by unplugging and plugging the power cord.
*7)
• Try to restart compressor every 3 minutes.
Try to start the compressor every 3 minutes.
*1 : The setting of ice making compartment will be displayed and blinks during or after ice making test operation.
*2 : This operation is called the recovery operation:
If the damper has not operated ever once during the compressor operation, make the damper operate when the compressor stops.
*3 : When the resistance is , the circuit is deemed open-circuited.
When the resistance is 0 , the circuit is deemed short-circuited.
*4 : Once E01 is detected, other errors would be ignored and not displayed on the panel.
*5 : Characteristic value may change in order to improve the product.
*6 : The error codes E50 to E55 are not displayed even if those abnormalities occur at power input.
Therefore, be sure to perform ice making test operation in order to check if any abnormality indicated by these error codes occurs. (See page 22.)
*7 : If those errors still continue for 1 minute after the restart, E56 will be displayed again.
25
5-3 BLOCK DIAGRAM OF PRINTED CIRCUIT BOARD
MR-E55R-C
MR-E60R-C
Operation P.C. board
• Setting up temperature, feature, quick mode and eco mode for each
compartment
• Display of self-check
• Outside air thermistor
• Buzzer
Control board
Control circuit of refrigerator
• Read/control each compartment temperature (Neuro-fuzzy)
• Control on timers
• Operation control of the parts such as fan motor or heater, etc. equipped inside/outside
Inverter control circuit of compressor
• Inverter control of compressor
• Inverter-drive power module
• Detection of bus-bar voltage
Parts outside/inside refrigerator
For 311V DC system
• Compressor
For 110V AC system
• Defrost heater 1
• Defrost heater 2
• Water tank heater
• Vegetable compartment heater
• Rotational heater board
• Water pipe heater
• Ice making tray heater
For 12V DC system
• Refrigerator fan motor
• Box fan
• Motor damper
• Ice maker gear box
• Three-way valve
• LED for bacteria removal from
water tank
• I-see sensor motor
• Interior LED
• Refrigerator deodorization LED
• Versa compartment supercool
freezing LED
• Vegetable compartment LED
5-4 AUTO ICE-MAKER
MR-E55R-C
MR-E60R-C
(1) Ice making cycle
Water supply
The ice tray is filled with water from the water tank.
Ice ejection
After the detection lever checks the amount of ice, the ice tray is rolled over for ice ejection.
When the ice storage box is filled with ice, the ice tray does not roll over.
(2) Automatic ice maker circuit
For 5V DC system
• Freezer compartment thermistor
• Refrigerator compartment thermistor
• Defrost thermistor
• Door switch (for refrigerator com-
partment, ice compartment & freezer
compartment)
• Ice tray thermistor
• Ice making compartment thermistor
• Vegetable compartment thermistor
• Position-specifying switch in ice
maker gear box
• Versa compartment thermistor
Ice making
Ice tray thermistor watches and controls the ice making operation
Ice stock
Ice is stocked in the ice storage box.
Ice making capacity is about 100 -
120 cubes a day.
Stock capacity of ice cubes is about
100 cubes.
(With 8-cube ice tray)
CN2A
Water tank heater
CN1A
CN9S
Water pipe heater
LED for bacteria removal from water tank
Water pump motor
9-pin connector
6-pin connector
Ice making compartment thermistor
CN5D
Ice tray thermistor
CN10K
Ice making gear box
8-pin connector
26
6-pin connector
(3) Operation by ice making test
Press the switch for 5 seconds or more.
(See 5-2(1) “• Self-check and error display method and operation, Ice making test operation”
Ice stock detective lever detects the amount of ice.
Detective lever once comes down to detection point then returns to the original position.
The ice tray is rolled over and the system is reset.
The ice tray rolls over once to drop the ice, then returns to the original position.
Water pump motor is operates.
Remove the lid of the water tank then check the sounds of water running.
Completion
When abnormality occurs, the error code is displayed on the panel.
Inspect the abnormal points by referring to page 23-25.
Ice making test completes about 20 seconds later.
Ice tray
Detection lever
(Upper ice making compartment)
Check here.
(Lower-left part of refrigerator compartment)
[Check point of automatic ice maker operation]
* Never touch the automatic ice maker while it is operating.
After the operational test, a popping sound is heard several times because the operation of three-way valve is checked automatically. During the operation, do not insert a hand into the automatic ice maker.
(4) Maintenance for water pump and water pipe
The inside of the pump can be cleaned after disassembling the pump in the water tank.
The inside of the pipe can be cleaned after disassembling the water supply pipe in the tank holder. Follow the procedures below when disassembling, cleaning, and assembling the pump and the pipe.
Be sure to explain to customers that they need to clean the water pump and the water supply pipe once a month.
After the test run, a “pop” sound is heard several times to automatically confirm the proper operation of the three-way valve.
Water pump & Light-type bacteria removing filter
1. Pull out the pipe. 2. Turn the tank
Water tank
Tank pipe pump to detach.
Water pump
Water pipe · Tank holder
4. Remove the light-type bacteria removing filter and
3. Pull out the tank pipe, turn the cap to remove, and then wash the propeller with water.
• The propeller is made of the magnet.
Wash it well with water so that no alien sub- stance remains on it.
Tank pipe
Propeller
Cap
Cover
Light-type bacteria removing filter wash it in water.
Normally the filter needs not be replaced. However, replace it in the following condition:
• When the filter is clogged by passing something other than water through the filter.
• When the filter is broken.
In such a case, contact the dealer where you purchased this refrigerator.
5. Put the parts back in the reverse order of disassembly.
2. Separate pieces and wash with water.
1. Pull out water supply pipe. Wipe the tank holder with clean cloth.
• Do not let water flow into the tank holder.
Water pipe
Tank holder
(5) Troubleshooting for automatic ice-maker
Packing Aluminum pipe
• Twist the aluminum pipe to replace it.
3. Reverse steps to replace the pipe.
Side A
Side B
Water pipe
• Replace the water pipe.
Be sure that sides
A and B fit flush to each other.
The ice does not come out from the tray water sau- cer
No waterdrops in water saucer
Water in the tank holder
Chained ice, water leaking from the ice server
The ice-maker gear box may be defective, cooling may be poor or ice cubes may be full in the ice storage box.
1. Check inside of the ice storage box.
• Ice cubes are not stored flatly and the amount is detected as full.
• Food inside the ice storage box
Inspection
2. Measure the resistance of ice tray thermistor circuit.
• Open circuit ( ) or short circuit (0 )
3. Check if the temperature of the freezer compartment is cool enough.
(It takes longer to make ice during summer days
or if the door is frequently opened.)
• Not enough
The water saucer may be defective, or the ice tray may get cracked.
4. Check the water pipe for dirt and foreign objects.
• Clogging
• Freezing (For freezing, check installation and measure the resistance of water pipe heater and tank heater.)
Replace the ice tray thermistor.
Poor cooling
Clean the water pipe.
Deice
Check connection of water pipe heater and tank heater.
5. Check the condition of ice tray.
• Broken or cracked
• Not placed properly
• Dirt or foreign objects 6. Disassemble the water pump and check the inside of the pipe.
7. Tank pipe is clogged, has a hole or is not • Clogging, disconnecting
• Hole or crack
Replace the tray.
Reinstall it properly.
Repair and explain to the user for proper usage.
Clean/Reinstall it properly.
Change the tank pipe.
8. Check the coil resistance of pump motor.
9. Check if there are any dirt or foreign objects which are difficult to remove in the water tank. Also, check if there is any crack or deformation on the tank.
• Crack or deformation
10. Check the water pipe for dirt and foreign objects.
Also, check the water pipe position and connection.
• Open or short circuit
• Clogging, disconnecting
• Hole or crack
Check the water pump.
Change the water tank.
Clean/Reinstall it properly.
Replace the pipe.
11. Check the water pump operation by the ice-making test
13. Measure the water pump coil resistance.
• Water filling period is longer than 9 seconds.
Replace the control board.
12. Water spill at the installation of water tank or more water over the full water level may cause formation of chained ice.
• Open or short circuit Change the water pump motor.
27
5-5 FLOWCHART OF TROUBLE CRITERION
MR-E55R-C
MR-E60R-C
Excessive cooling No cooling, poor cooling
Is the temperature of refrigerator compartment/ set to “Low”?
Yes
No Set the temperature to
“Low”.
Is the temperature of refrigerator compartment/ set to “High”?
Yes
No Set the temperature to
“High”.
Only food around the air outlet gets frozen.
No
Yes Keep the food away from air outlet.
Normal
Is the motor damper (for refrigerator compartment/slide compartment) covered with frost?
No
Check the refrigerator compartment thermistor.
Dip refrigerator compartment thermistor into ice water (0 ), disconnect the 2-pin connector, and measure resistance between (white) and (white).
• Resistance at 0 : approx. 6-7k .
Yes
Open the refrigerator compartment door and attach a magnet on the door switch to check that cold air blows from the outlet. (See 1)
Yes
Expose the damper (for refrigerator compartment/slide compartment) so that its operation can be visibly checked and conduct an ice-making test. Does the baffle open/close?
(Wait 1 minute for self-check).
(See “Self check method and its operation, Ice making test operation” at page 22.)
The baffle does not operate
Refrigerator compartment thermistor abnormal
No Proceed to [5] at page
32.
Replace the motor damper (for refrigerator compartment/slide chilled compartment)
Motor damper is combined with fan grille assembly.
Repair the frosted part.
Replace the refrigerator compartment thermistor.
Weak
Refrigerator compartment
Low
Cooling
Middle High
Strong
CN9S
4-pin connector
Refrigerator compartment thermistor
1
Refrigerator compartment
Attach a magnet bar here.
Ice making compartment
Versa compartment
Adjustment of the set temperature is possible. Page 20
28
Poor cooling
1 Is the set temperature of freezer compartment set to “High”?
Yes
2 Does cool air come out of air outlet when opening the refrigerator compartment door and attaching a magnet bar on the door switch ?
Yes
3 Check freezer compartment thermistor.
Dip freezer compartment thermistor into ice water (0 ), and measure the resistance between terminal (white) and
•
(white) by detaching 2-pin connector at the left-back bottom of vegetable compartment.
Resistance at 0 :approx. 6~7k .
Defective thermistor
Replace freezer compartment thermistor
No
No
Normal
Set the temperature to “High”.
Proceed to “The refrigerator fan motor does not work.”
When compressor operates, E41 of self-check.
is displayed as a result
Exchange the unit.
4-pin connector
Freezer compartment
thermistor
CN9S
Adjustment of the set temperature is possible. Page 20
Not cooling at all (In case any error codes doesn’t appear as shown in pages 30, 31 even though switch is pressed for 5 seconds)
Yes
Is refrigerator in the demonstration mode?
Release the demonstration mode. (See page 11.)
No
Does 110V AC run between and terminals of CN1 on filter board?
No Inspect power-supply wiring such as power cord and breaker etc.
Yes
Is the voltage between and , terminal of
CN2 on the filter board 110V AC?
No
Replace the filter board.
Yes
Remove the CN1A connector on the control board and the CN2 connector on the filter board and check for continuity between the
CN1A terminal and the CN2 connector terminal on the wiring side. (Check for short and/or open circuit on the motor protector.)
Continuity detected
No continuity
Detach connector CN50G on control board and check the resistance respectively between terminals of and :approx. 12.4 .
No continuity
Continuity detected
Motor protector (open circuit)
Just in case, by measuring the resistance, ensure that the circuit is open.
Abnormal
Measure the resistance of compressor’s winding between terminals of black, white, and red: approx. 12.4 .
Check the error display of selfcheck after turning on and off the power supply.
With all the connectors connected.
Abnormal
Normal
Exchange the unit.
Replace the lead wire assembly (lead wire of compressor).
Lead wire assembly
Reactor
Inverter-related parts may be defective. Conduct ice making test operation. (See pages 30, 31 for error codes.) CN1
Filter board
CN2
2-pin connector
Motor protector Compressor
Noise filter
2-pin connector
CN1A CN50G
Control board
29
Inverter-related indication “Compressor does not operate”
Error code
Abnormality Possible cause Symptom
E50
Trouble of inverter circuit
• When there is any trouble in the circuit which detects phase current of compressor.
Compressor does not rotate.
Replace the control board.
Measures
E51
Bus-bar voltage is abnormal.
• Power supply voltage is abnormal.
Compressor does not rotate.
• Defective reactor on the N/F board
Start
Measure the voltage of power supply.
99V or less
Arrange power supply to obtain the rated voltage,
99~121V.
121V or more
Arrange power supply to make the voltage within 121V and conduct the following checks.
E52
Does 121V AC run between CN1A terminals and , on the control board?
(See page 42.)
No
Check the connection between filter board and control board.
Abnormal
Connect them properly.
Yes
Replace the control board.
Normal
Replace the filter board.
Trouble of inverter software reset function
• When the inverter driving software malfunctions due to electric noise.
Compressor does not rotate.
Unplug the power cord and wait more than 10 minutes then plug it again
E52
Check the error code by performing the ice making test operation.
displays again.
No error code display
E53
Replace the control board.
Explain to customer.
• Abnormal start-up
• Abnormal synchronization
• Trouble of overcurrent detection
• Compressor motor gets locked.
• Defective circuit on control board
• Defective contact of CN50G on control board
Compressor does not rotate.
Start
Remove the CN50G connector on the control board, and measure the resistance on the compressor.
Are the resistances between the terminals
- , - , and
- respectively approx. 12.4 (20 )?
Yes
No
Measure the resistance of compressor’s winding between each terminal. Is the resistance approx. 12.4
(20 )?
No
Yes
*Replace lead wire assembly.
Exchange the unit.
*Is compressor
energized at
startup?
No
Yes
Replace the compressor.
Check the connection status of the CN50G connector on the control board.
Abnormal
Normal
Replace the control board.
Correct the connection of the CN50G connector on the control board.
*If control board is normal, compressor is energized every 10 minutes.
Compressor vibrates at startup when it is being energized. Touch it with your hand to check.
30
Inverter-related indication “Compressor does not operate”
Error code
Abnormality Possible cause Symptom
E56
• Defective wiring continuity
• Trouble of the control board
• Defective connection of connectors related to compressor
(board-side, relay, comp-side)
• Defective wiring connecting of the compressor
• Trouble of control board
• Trouble of compressor
Compressor cannot be activeted for more than 1.5 hours.
1. Locate the trouble and decide the measures.
• Decide the measures by checking the followings.
(1) Defective connector connections.
(Board-side, wire to wire, comp-side)
(2) Resistance of compressor’s winding
2. Flowchart of troubleshooting
start
Connector CN50G on the control board is properly connected?
Measures
No
Check Treatment
Connect properly.
Yes
Compressor
CN50G
Control board
Point+2 (to measure resistance)
For checking the connection to compressor
Lead wire assembly
Point+1 (to measure resistance)
For checking the lead wire assembly to compressor
The connector of compressor
is properly connected?
Yes
No
Remove the CN50G connector on the control board, and measure the winding resistance on the compressor. , and
(Point1). Is the resistance approx. 12.4
Ω (at 20ºC)?
No
Yes
Measure the resistance of compressor’s winding between individual terminals (Point 2).
Is the resistance approx. 12.4
Ω
(at 20ºC)?
No
Yes
Exchange the unit.
Replace the lead wire assembly.
Is compressor being energized at startup?
No
Replace the control board.
Exchange the unit.
Yes
Replace it only when error display keeps blinking even though all the above mentioned connectors are
properly connected.
E57 Inverter drive module abnormality
3. Recheck after measures
• After any measures are taken, unplug and plug power cord again to check if the compressor operates properly.
• If the compressor can operate properly for more than 1 minute after power cord is plugged again, it’s presumed that the cause of trouble is eliminated.
*If the cause of trouble cannot be eliminated, E56 will be displayed again 1 minute later after the power cord is plugged again.
*If the control board has been replaced, E56 won’t be displayed even though the cause of trouble is still not eliminated. In such a case, perform the ice making test operation to check what the error is. At the same time, also confirm that the compressor is operating for more than 3 minutes and each compartment is getting cooled.
Failure of the inverter drive module in the control
P.C. board
Overcurrent is detected in the inverter drive module before starting the compressor, and the compressor does not start rotating.
31
Replace the control board.
Poor cooling
1 Short-circuit the terminals and of the compulsory defrosting terminals (CN7M) of the control board to actuate the compulsory defrosting function and check whether the defrost heater is working properly. *1
No
2 Check if there is continuity between thermal fuse and defrost heater 1.
Yes
No
Yes (heats up)
Check the following and explain the result: half-open door, space between gaskets, the amount of ice.
Replace the defrost heater 1 and the thermal fuse.
Check the resistance of the defrost thermistor.
CN9S
CN1A
CN2A
1-pin connector
4-pin connector
Thermal fuse
<Control board>
Short circuit
1
CN7M
Compulsory defrosting
Defrost heater 1
4-pin connector
Defrost thermistor
*1 The compulsory defrosting will not work when the temperature of the defrost thermistor is 14°C or more.
1
2
3
Unplug and plug the power cord to perform self-check on refrigerator fan motor. Is the display indicating abnormality?
Unplug and plug the power cord to check if box fan is rotating.
No
Running
Check the door switch for continuity.
• Open and close the refrigerator door several times and check if the interior LED will be turned on and off (interior
LED should get turned off when the door comes 10 mm close to the refrigerator body .)
• Close the refrigerator compartment door until the LED is turned off . Open and close the ice making compartment door , and from the space of refrigerator compartment door, check that the interior LED is turned on and off.
Yes
Not rotating
Interior LED is not turned on and off.
4
Replace refrigerator fan motor.
Note: Refrigerator fan motor is combined
with fan grille.
Check if CN5D connector on control board is connected properly.
If it is, replace the control board.
Check the continuity by disconnecting the CN9S on the control board.
Normal
Abnormal Contact failure of connector.
Connect it properly.
Check if the connector on the door switch is connected properly. If it is, replace the door switch.
Interior LED is turned on and off properly.
5 Check if there is continuity in 4-pin fan motor connector in versa compartment.
No continuity
Connect the connectors properly.
Continuity detected
Door switches for refrigerator compartment (right and left) and ice making compartment
Doors Any one of the doors is open
R-door (right, left): closed
Door of the ice making compartment : closed
Replace refrigerator fan motor.
Note: Refrigerator fan motor is combined
with fan grille.
If any one of those doors is open, the switch between
and , terminals of 3-pin connector, will be OFF.
etc 1 2
3-Pin connector between
1 and 3
OFF ON
CN9S
8-pin connector
Reed switch board
3-pin connector
Refrigerator compartment
(right and left)/ Ice making compartment door switch
5~10mm
2-pin connector
Freezer compartment door switch
Right door of refrigerator compartment
CN5D
4-pin connector 4-pin connector
Refrigerator fan motor
Left door of refrigerator comparttment
Door of ice maki ng compartment
Door of versa compartment
Door of freezer compartment
Door of vegetable compartment
32
Excessive cooling
Is the temperature of vegetable compartment set to “Low”?
Yes
No Set the temperature to
“Low”.
No
Poor cooling
Is the temperature of vegetable compartment set to “High”?
Yes
No Set the temperature to
“High”.
Yes Is the temperature of freezer compartment set to “Low”?
Set the temperature to
“Middle” or “High”.
Expose the damper (for refrigerator compartment/ slide compartment) so that its operation can be visibly checked and conduct an ice-making test. Does the baffle open/close?
Normal
No Is connector CN5D on control board connected properly?
No
Yes
Disconnect CN5D and measure the resistances between and
, and between and .
Check that the winding of motor damper (for vegetable compartment/ versa compartment) has a resistance of approx. 415 .
0 or
Normal
Is the motor damper covered with frost?
Not frosted
Frosted
Check the thermistor on the vegetable compartment.
1. Dip the thermistor into ice water with a temperature of 0 .
2. Remove the 4-pin connector from the connector box on the upper-left-front.
3. Measure between the terminals - .
• Resistance at 0 : Approx. 6~7k
Defective thermistor
Connect the connector properly.
No
Is 6-pin connector which is in connector cover on the back of ice maiking compartment connected properly?
(6-pin connector is connected to motor damper.
Refer to the figure below.)
Yes
Replace the motor damper (for vegetable compartment/versa compartment).
Replace the fan grille as well as the motor damper because they are combined together.
Repair the frosted part.
Replace the vegetable compartment thermistor.
CN5D
CN2A
CN1A
CN9S
CN10K
CN5D
6-pin connector
Motor damper
(for vegetable copartment/
versa compartment)
2-pin connector
5-pin connector
Vegetable compartment heater
2-pin connector
Vegetable compartment thermistor
Operation P.C. board
Outside air thermistor
TH1
Adjustment of the set temperature is possible. Page 20
33
only applies to versa compartment.
Excessive cooling No cooling; poor cooling
Yes
Which operation mode is versa compartment set to?
set to “Low”?
Only the food around cool-air outlet is excessively cooled.
No
Is the temperature
Yes
It is set to “Soft freezing”.
No food.
Set the temperature to “Low”.
Keep food away from air outlet when storing
Make the operation of motor damper (for versa compartment/vegetable compartment) visible, and conduct ice making test. Check that the baffles open and close. (Wait
1 minute for self-check.)
(See “• Self-check and error display method and operation, Ice making test operation” on page
22.)
The baffles do not function
Is connector CN5D on control board connected properly?
Yes
Disconnect CN5D and measure the resistance between and , and between and .
Check that the winding of motor damper (for versa compartment/ vegetable compartment) has a resistance of approx. 415 .
No
0 or
Normal
Normal
Is the motor damper covered with frost?
Not frosted
Frosted
Check the versa compartment thermistor.
Dip the versa compartment thermistor into the ice water
(0 ) and disconnect 6-pin connector for fan grille at the back of versa compartment. Measure the resistance between terminals (white) and (white).
• Resistance at 0 : Approx. 6~7k
Check the ice making compartment thermistor.
Dip the ice making compartment thermistor into the ice water (0 ) and disconnect 6-pin connector of fan grille at the back of ice making compartment. Measure the resistance between terminals (white) and (white).
• Resistance at 0 : Approx. 6~7k
Which operation mode is versa compartment set to?
It is set to “Soft freezing”.
It is set to “Freezer”.
Is the temperature set to “High”?
No
Set the temperature to “High”.
Yes
Check the set temperature in freezer compartment. Is the temperature set to “High”?
1
Does cool air come out of air outlet when opening the refrigeratorcompartment door and attaching a magnet bar on the door switch?
Yes
No
No
Set the temperature to
“High”.
Refer to the section:
“The refrigerator fan motor does not work”.
Connect the connector properly.
No
Is 6-pin connector which is in connector cover on the back of ice making compartment connected properly?
(6-pin connector is connected to motor damper.
Refer to the figure below.)
Yes
Replace the motor damper (for versa compartment/vegetable compartment).
Replace the fan grille as well as the motor damper because they are combined together.
Defective thermistor
Defective thermistor
Repair the frosted part.
Replace the versa compartment thermistor.
Replace the ice making compartment thermistor.
CN5D
6 -pin connector
Adjustment of the set temperature is possible. Page 20
Motor damper
(for refrigerator compartment/
ice making compartment)
Ice making compartment thermistor
CN9S
6 -pin connector
Versa compartment thermistor
Motor damper
(for versa compartment/
vegetable compartment)
1
Refrigerator compartment
Ice making compartment
Versa compartment
Attach a magnet bar here.
34
5-6 TROUBLE CRITERION OF MAIN PARTS
MR-E55R-C MR-E60R-C
Components/
Part Name
Check Method and Criterion
Compressor
White
Model EFI100E13DHH
Rated input
Starting current
W
A
45 (1620 rpm)
4.0
Black Red
Running current
A
0.69 (1620 rpm)
(For only 1 minute after startup)
Normal
Abnormal
(faulty)
Measure the resistance with a tester.
Winding
(Black-White)
(White-Red)
(Red-Black)
12.4
(20 )
Open ( ) or short circuit (0 )
Motor protector
Model MM3-71CCV
Connected point
Open
100 ± 50 or more
Energize it at 17.0A, 25 for 16 seconds at the longest.
Close 61±8 or less
Measure the resistance with a tester. (Ambient temperature: Room temperature)
Parts Mounted
Position
In the machine chamber at the rear side of the frame
In the machine chamber at the rear side of the frame
1
Contact point
2 Normal
Less than 1
Abnormal (faulty)
Open circuit ( 0 )
Refrigerator fan motor
Machine chamber fan motor
1 2
Model
Number of poles
Diameter
UDQM002B3
DC brushless
10
150 (Mixed flow fan)
Measure the resistance with a tester. (Ambient temperature : Room temperature)
Normal
Abnormal
(faulty)
Between and (GND and IC
Power): About 12k
Between and : open circuit ( )
IC Power):
Between and : short circuit (0 )
2
1
4
3
IC Power
Power
FG
GND
IC
1 2 3 4 : Pin No.
Model 4715JL04WS16G51
Operation method During compressor operation
Measure the resistance with a tester. (Ambient temperature: Room temperature)
In the fan grille of the freezer compartment
In the machine chamber at the rear side of the frame
4 3 2 1 Pin No.
Normal Abnormal (faulty)
Between and (GND and
Vcc): About 25k and : open circuit ( )
Between and (Vs and Vcc): Between and : short circuit (0 )
35
Components/
Part Name
Water pump motor
Check Method and Criterion
Measure the resistance with a tester. (Ambient temperature : Room temperature)
Normal
16 (Approx.)
Abnormal (faulty)
Open ( ) or short circuit
(0 )
Parts Mounted
Position
Under the water tank holder in refrigerator compartment
Motor damper for refrigerator compartment/ ice making compartment
Measure the winding resistance.
(
Winding
Blue-White
Red-Yellow
)
Normal
415
(Approx.)
Red
Abnormal (faulty)
Open ( ) or short circuit
(0 )
In the fan grille for freezer compartment
Connector is at the left-back bottom of refrigerator compartment.
Yellow
Blue White
Motor damper for versa compartment/vegetable compartment
Measure the winding resistance.
(
Winding
Blue-White
Red-Yellow
)
Normal
415
(Approx.)
Red
Abnormal (faulty)
Open ( ) or short circuit
(0 )
In the fan grille for freezer compartment
Connector is at the back of versa compartment.
Yellow
Blue White
36
Components/
Part Name
Defrost heater 1
Check Method and Criterion
Rated input W
Operation method
150
The heater is energized while defrosting.
(Defrosting is finished when the evaporator is 14±1.5 or more)
Measure the resistance with a tester. (Ambient temperature : Room temperature)
Parts Mounted
Position
At the drip tray under the evaporator of the freezer compartment.
Normal
81
(Approx.)
Abnormal (faulty)
Open circuit ( )
Defrost heater 2
Vegetable compartment heater
Water pipe heater
Rated input W
Operation method
86
The heater is energized while defrosting.
(Defrosting is finished when the evaporator is 14±1.5 or more)
Measure the resistance with a tester. (Ambient temperature : Room temperature)
Normal
141
(Approx.)
Abnormal (faulty)
Open circuit ( )
Measure the resistance with a tester. (Ambient temperature : Room temperature)
1.7k
Normal
(Approx.)
Abnormal (faulty)
Open circuit ( )
Embedded in the evaporator
(protected with the dedicated aluminum piping)
At the bottom of the vegetable compartment
(inside polyurethane foam)
The connectors are in the connector box on the ceiling of the vegetable compartment
Operation method
The heater is turned on when vegetable compartment thermistor has reached a lower temperature than the set temperature for vegetable compartment.
Measure the resistance with a tester. (Ambient temperature : Room temperature) Under the water tank holder
Normal
3.0k
(Approx.)
Abnormal (faulty)
Open circuit ( )
Water tank heater
Operation method
When ice-making thermistor has reached approx. 10 or below, the heater is turned on with energizing rate adjusted by the set temperature of refrigerator compartment and freezer compartment.
Measure the resistance with a tester. (Ambient temperature : Room temperature) Under the water tank holder
Normal
3.0k
(Approx.)
Abnormal (faulty)
Open circuit ( )
Operation method
The heater is turned on with energizing rate adjusted by the set temperature of refrigerator compartment.
37
Components/
Part Name
Rotational heater board
Check Method and Criterion
Measure the resistance with a tester. (Ambient temperature : Room temperature)
Parts Mounted
Position
In partition of refrigerator compartment door
Normal
1.5k
(Approx.)
Abnormal (faulty)
Open circuit ( )
Ice making tray heater
Operation method
While compressor is operating, the heater is turned on.
When compressor stops, the heater is suspended for the first 20 minutes and then reactivated.
Measure the resistance with a tester. (Ambient temperature: Room temperature) Lower part of ice tray
Normal
1.0k (Approx.)
Abnormal (faulty)
Open circuit ( )
Thermistor
Operation method
During CRYSTAL ICE mode
(The heater is turned on 5 minutes after water supply for up to 4 hours.)
Measure the resistance with a tester according to the following graph.
(Thermistor resistance values against temperature)
Defrost
thermistor
Evaporator
• Resistance measured under the ambient temperature from -50 to +50
1. 200 to 500 k •••••••••••••••••Normal
2. Out of the above range •••••••••Abnormal
35
30
25
20
15
10
5
0
Refrigerator
compartment
Ice making tray
thermistor
Thermistor resistance values against temperature
Freezer
compartment
Defrosting
Versa
compartment
Ice making
compartment
Vegetable
compartment
-20
Inner thermistor
-10
Outside air thermistor
(In the operation
P.C. board)
0 10
Temperature
20 30
Thermistor Check Procedure
• Thermistor resistance value will vary with the change of temperature.
• Take the temperature around the thermistor, and then measure thermistor resistance using a tester.
The relation between resistance and temperature is as shown on the left side.
Troubleshooting with self-check
(1) If the self-check indicates the abnormality of thermistor when the power is turned on, measure the resistance of the thermistor.
• If there is a short circuit in the thermistor, there may be a defect in the contact of the connector or the element of the thermistor.
(2) When the self-check indicates the abnormality of thermistor a few seconds after the power is turned on, check the contact of the connector.
Ice making
thermistor,
Versa
compartment
thermistor,
and Freezer
compartment
thermistor
In the fan grille
of each
compartment
Vegetable
compartment
In the back of
partitions
between
Freezing and
Vegetable
compartments
Ice making
tray
thermistor
In the ice
making
compartment
Refrigerator
compartment
thermistor
Back of the
refrigerator
control panel
Outside air
thermistor
In the operation
P.C. board
38
Components/
Part Name
Three-way valve
LED for bacteria removal from water tank
(12V DC)
Check Method and Criterion
A 5
Model NSCE001DC1
A 2
1
B
3
COM
4
B
Normal
54~66 (Gray
[common] A/ A/ B/
B each phase)
Abnormal
Open ( ) or short circuit (0 )
1 2 3 4 5
B A COM B A
Check the operation of three-way valve
Check the operation by following either (1) or (2) below. When a popping sound is heard 1 to 25 times, it is considered that the valve is operating normally. The sound is clearly heard around the back of the product.
(1) Reset the power supply. Check the operation right after this.
(2) Ice making test. Check the operation right after the test is over.
Parts Mounted
Position
In the machine chamber at the rear side of the frame
On the external surface of the tank holder
LED lighting duration
Abnormal criterion
• After water is supplied to the ice tray.
• After the ice level sensor lever detects that ice storage becomes full.
• While the door is kept open for maximum of 5 minutes.
When the door is opened, LED goes out within 5 minutes.
Make sure if the connector is securely connected.
LED
Note: LED cannot be replaced individually because it is embedded in the tank holder.
LEDs
(Vegetable compartment)
Photosynthesis LED (2 pieces)
LED lighting duration
Abnormal criterion
Always
Means
LEDs light in following colors at the above timing.
Photosynthesis LED: Orange
Check with the diode range( ) of tester.
(Use a tester equipped with diode range.)
The pointer of the tester does not shake when measuring between 2-pin connector No.1 (-) and No.2 (+). Make sure the pointer of the tester does not shake even if the polarities are reversed. Resistance: Short-circuited (0 Ω )
Photosynthesis
LED
Use a tester equipped with a diode range
LED
On the ceiling vegetable compartment
(Vegetable
compartment
LED board)
2 1
39
Components/
Part Name
Interior LED
(12V DC)
Refrigerator deodorization LED
(12V DC)
Versa compartment supercool freezing
LED (12V DC)
LED lighting duration
Abnormal criterion
LED lighting duration
Abnormal criterion
LED lighting duration
Abnormal criterion
Check Method and Criterion
It lights up while the refrigerator compartment door is open.(If the door stays open for 60 minutes in a row, the LED automatically goes off. Once the door is closed, it will light up again next time the door is opened.)
The LED does not go on at the above timing.
1. While the i-see sensor motor is moving
2. During the defrost process, or for about 10 minutes after defrosting completes
3. For about 90 seconds after the compressor stops
4. While the compartment door (refrigerator, ice making, and/or freezer compartment) is opened (for 5 minutes at the maximum)
This LED and the versa compartment supercool freezing LED light up simultaneously.
The light does not go on at the above timing.
1. While the i-see sensor motor is moving
2. During the defrost process, or for about 10 minutes after defrosting completes
3. For about 90 seconds after the compressor stops
4. While the compartment door (refrigerator, ice making, and/or freezer compartment) is opened (for 5 minutes at the maximum)
This LED and the refrigerator deodorization LED light up simultaneously.
The light does not go on at the above timing.
Parts Mounted
Position
In the refrigerator
compartment: on the left and right wall towards the front of the compartment
(Interior LED
control board)
In the refrigerator compartment: in the control panel which is towards the back of the compartment
(Refrigerator
deodorization LED
control board)
On the ceiling near front in the versa compartment
(Mounted on the
i-see sensor motor:
Versa compartment
supercool freezing
LED control board)
40
Components/
Part Name i-see sensor motor (12V DC)
Check Method and Criterion
Model
Resistance
NSEV001DA1
126 - 154 (common-A/A/B/B each phase)
1) Operation check… Refer to “Operation check of the i-see sensor
Abnormal criterion
2) Resistance check… Open or short
<Operation check of the i-see sensor>
The i-see sensor motor operates by performing (1) or (2) below. Open the versa compartment door to visually con fi rm the operation.
Parts Mounted
Position
On the ceiling near front in the versa compartment
(1) Power reset (Check the operation right after the power is reset.)
(2) Ice making test (Check the operation right after the ice making test.)
Operation of the i-see sensor motor
The operation pattern during the operation checking is different according to which starting
procedure, (1) or (2), was selected.
(1) The operation was started by the power reset
The motor moves from back to front.
The motor moves from front to back, and stops
at the prescribed position.
(2) The operation was started by the ice making test
The motor moves from front to back
The motor moves from back to front.
The motor moves from front to back, and stops
at the prescribed position.
5
2
1
A
4
3
B
COM
A
B
41
5-7 TEST POINT DIAGRAM OF FILTER BOARD
MR-E55R-C
MR-E60R-C
CN1
110V AC
3
1
5-8 TEST POINT DIAGRAM OF CONTROL BOARD
MR-E55R-C
MR-E60R-C
The capacitor that is used for the inverter is charged to 330V DC, so electric charge remains for a while even after power off.
Therefore, an electric shock may occur if the charging portion is touched by hand.
Short-circuiting between J91C and J92 for 20 seconds or longer with a tool such as a flat-blade screwdriver allows the capacitor to discharge safely. When replacement of the control board follows, be sure to perform this operation.
After discharge, measure between the C91C terminals + and – with a tester. Before inspection, be sure to check that the voltage is 10V DC or lower.
Compulsory defrosting by short circuit
CN7M
280~340V DC
5
7
1
3
CN1A
110V AC
Ice tray heater
Tank heater
CN2A
1 Rotational heater board
3 Water pipe heater
5 Vegetable compartment heater
7 Defrost heater 2 (for evaporator pipe)
9 Defrost heater 1 (for Glass tube heater)
+5V DC
(Refrigerator
control board)
CN50G
Compressor
+12V~14V DC
(Refrigerator
control circuit)
CN4D
8 7 6 5 4 3 2 1
CN5D
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
CN10K
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
CN9S
1 2 3 4 5 6 7 8 9 10 11 12 13 14
+5V DC
(Inverter circuit)
+12~20V DC
(Inverter circuit)
CN61L
2 1
42
5-9 TROUBLESHOOTING FOR SUPERCOOL FREEZING OPERATION
5-9.1 FAQ
1
Symptom/Problem
Supercool freezing does not keep foods fresh.
Supercool freezing does not work.
Possible cause
Improper supercool freezing operation
Explanation to the customer/Solution
• The amount of drip from meat and/or fi sh is same as before.
• Meat is dried out.
• Potatoes become fl oury.
• Vegetables lose their crispy texture.
• Bamboo shoots are sinewy.
• Rice is not tasty.
• The versa compartment is not set to the soft freezing mode.
• Supercool freezing button is not pressed.
• Food was added to the compartment in the middle of the supercool freezing mode.
• Food is wrapped in aluminum foil or paper.
• A separate item of food is on the top of the food for supercool freezing and preventing even supercool freezing.
• Food that had thawed out once was refrozen.
• Food is old or expired.
• Hot food and cold food are put in the compartment at the same time.
• Set the versa compartment to the soft freezing mode. (Supercool freezing is only available in the soft freezing mode.)
• Be sure to press the supercool freezing button.
• Food that was added to the compartment in the middle of the supercool freezing mode may not be frozen.
• The temperature of wrapped food is difficult to be detected by the supercool freezing sensor.
• Refrozen food and old food may not besupercool-freezed occasionally.
• As the cooling of hot food takes precedence over that of cold food, the cold food may not be supercooled occasionally.
2 Food does not freeze after one night.
Yoghurt does not freeze.
Meat and fi sh do not freeze.
Fresh jam does not freeze.
Check the settings of the versa compartment.
• The versa compartment is not set to the soft freezing mode.
• The compartment is set to “Low.”
• The compartment doors are opened and closed frequently.
• The coagulating temperature of the food is low.
(e.g. processed food, such as soybean paste)
• Set the versa compartment to the soft freezing mode.
• Set the compartment to “High.”
• Open and close the compartment doors as infrequently as possible during the supercool freezing mode. Since this function freezes the food at a slow speed, it takes a long time to complete freezing.
• Food with a low coagulating temperature may not freeze in the soft freezing mode.
3 Food and drink freeze hard. (They are not maintained in the supercooled state.)
Water in a plastic bottle freezes hard.
Drinks freeze hard.
• The user did not check the food and drink
right after the
display goes out.
indicator on the
• Supercool freezing is a function which releases the object from the supercooling state and freezes it into the fine particles. When the supercool freezing indicator goes out, supercooling is over.
• It is dif fi cult to make supercooled water in the refrigerator. (It does not always work well.)
4 When the food is frozen, the state of food looks same as that frozen in the normal freezer. Check the settings of the versa compartment.
Icicles form on the surface.
There is some frost.
5 Food in the versa compartment melts.
• The versa compartment is not set to the soft mode.
• The food is stored for a long time.
• The compartment doors are opened and closed frequently.
Check the settings of the versa compartment.
• Set the versa compartment to the soft freezing mode.
• The longer the food is stored, the more frost forms.
• Frequent door opening changes temperature inside the refrigerator. That causes frost formation.
• The food is in contact with hot food.
• The “supercool freezing” button was not pressed when hot food is put in the compartment.
• Food with temperature that is more than
80 is in the compartment.
• The doors are not closed completely.
Supercool freezing is not available in the following operation
For 4 hours after the power is turned on
• Cooling for the whole refrigerator has priority over the supercool freezing mode.
When the temperatures in the other compartments rise to higher than a certain degree
• Cooling for the other compartments has priority over the supercool freezing mode.
When the temperature of the versa compartment is out of the speci fi ed temperature range for soft freezing
• Right after switching from other than soft freezing mode
(The instruction manual mentions that supercool freezing should be started about 2 hours after switching to soft freezing.)
43
5-9.2 Failure diagnosis
First diagnosis…Diagnosis of air path switching according to food temperature
Do not remove the power plug. (The supercool freezing mode is not available for four hours after the power is
Check the temperature of the versa compartment when the supercool freezing mode is OFF.
(Make sure that the cooling function is working properly according to the settings of soft freezing.)
Press the button. (The control varies depending on the temperatures of the food to be supercooled.)
• When the food temperature is low (about 25 or less):Turning on supercool freezing starts the supercool freezing control.
5 minutes later make sure the cool air stops coming out from the air outlet on the back of the versa compartment.
Note : Turning on supercool freezing raises the temperature in the versa compartment compared to that measured in
(to prevent freezing from the surface). (Refer to 1 for details.)
• When the food temperature is high (about 25 or more): Turning on supercool freezing starts the fast cooling control.
5 minutes later make sure the cool air is coming out from the air outlet on the back and ceiling of the versa compartment.
When fast cooling ends, if the food temperature is low enough, the supercool freezing control will start.
If the control performs as it is mentioned above, the air fl ow control is working properly and the supercool freezing
function is normal
Second diagnosis…Diagnosis made with food
Prepare two pouches of ready-meal-style curry. Freeze one in the freezer and supercool-freeze the other in the
versa compartment. Compare the texture of the ingredients, especially potatoes, in the curry.
Put a pouch of ready-meal-style curry in the versa compartment, and press the supercool freezing button.
Put the other pouch of ready-meal-style curry in the freezer.
Let the both pouches stay in there more than overnight.
Warm up and thaw the frozen curry and check the texture of potatoes.
If the potatoes in the supercooled curry maintains higher fi rmness compared to the ones in the frozen curry,
the supercool freezing function has no problem.
Rear air outlet
Twin damper
1: Supercool freezing control
The temperature in the versa compartment is, at least for 50 minutes, set to approximately 4°C lower than the temperature before supercool freezing is set.
It is normal that the temperature rises after the supercool freezing is set.
44
5-9.3 Failure diagnosis for the thermopile (HIKARI i-see Sensor)
1. Diagnostic procedure <Outline>
• In the “Thermistor check mode”, check the following: Response and Detected temperature.
• Set the versa compartment to “soft freezing” and check and .
Response check: Make sure that the detected temperature changes by placing your hand under the sensor.
Detected temperature check: Put the vinyl tape on the aperture of the thermopile, and check the detected temperature.
Accuracy of the temperature detected by the thermopile
• Since there is considerable individual variation in the temperature detected by the thermopile, the tolerance of the absolute temperature is
relatively large.
• It is controlled by the relative temperature so that the thermopile’s individual variation does not affect the refrigerator.
If no problem is found by the check , it is generally regarded as normal.
If the check results in normal, it can be regarded as normal even if the detected temperature, found by the check , is slightly out of
the normal range.
2. Diagnosis
1) Procedure for Response check
Step 1: Start the “Thermistor check” mode.
Step 2: Confirm that the detected temperature changes by placing your hand under the thermopile.
(2) Failure diagnosis
• If the temperature does not rise 2 to 3 or more when your hand is introduced, the thermopile is broken.
(However, if the inside of refrigerator is not cool enough, the temperature change cannot be observed.)
2) Procedure for Detected temperature check
Step 1: Open the versa compartment. Put the vinyl tape to cover the aperture of i-see Sensor monitor.
Step 2: Wait for about five minutes until the temperature of the versa compartment becomes stable.
Step 3: Start the “Thermistor temperature check mode”.
Step 4: Check the temperature of the versa compartment thermistor and the thermopile temperature.
(2) Failure diagnosis
• If the temperature detected by the thermopile is roughly in the range of − 2 to + 5 against the temperature of the versa com-
partment thermistor, which is listed in the temperature control chart ("ELECTRICAL SPECIFICATIONS" of "2. SPECIFICATIONS"),
it is normal.
(The temperature of the thermopile tends to be 3 to 5 higher than the temperature detected by the versa compartment thermistor.)
<Reference> E55R Temperature control chart
Freezer thermistor
Refrigerator thermistor
Versa compartment thermistor
Ice making thermistor
Vegetable compartment thermistor
Vegetable compartment thermistor
Model
Low
Middle
High
Model
Low
Middle
High
( )
( )
( )
( )
( )
( )
Model
Soft freezing(Low) ( )
Soft freezing(Middle) ( )
Soft freezing(High) ( )
Freezer(Low) ( )
Freezer(Middle) ( )
Freezer(High)
Model
( )
Ice making ( )
Ice making stop ( )
Crystal ice making ( )
Model
Low
Middle
High
Model
Low
Middle
High
( )
( )
( )
( )
( )
( )
NTC thermistor
− 14.3/ − 16.0
(ON/OFF)
− 18.9/ − 20.6
− 22.2/ − 23.8
(ON/OFF)
(ON/OFF)
NTC thermistor
8.4/6.4
(Open/Close)
5.1/3.2
1.9/0.1
(Open/Close)
(Open/Close)
NTC thermistor
− 5.9/ − 7.1
(Open/Close)
− 9.8/ − 11.1
− 11.1/ − 12.3
(Open/Close)
(Open/Close)
− 12.0/ − 15.1
− 16.1/ − 19.4
(Open/Close)
(Open/Close)
− 17.7/ − 21.2
(Open/Close)
NTC thermistor
− 21.6/ − 23.4
− 21.6/ − 23.4
(Open/Close)
(Open/Close)
− 21.6/ − 23.4
(Open/Close)
NTC thermistor
10.7/8.7
9.0/7.0
(Open/Close)
(Open/Close)
7.0/5.1
(Open/Close)
NTC thermistor
7.7/6.4
6.1/4.8
4.2/2.9
(OFF/ON)
(OFF/ON)
(OFF/ON)
45
Put the vinyl tape onthe aperture.
Thermopile detected temperature
It is normal if the detected temperature is in the range of − 2 to +5 against the temperature of the versa compartment thermistor.
− 1
− 5
− 6
/
/
/
− 9
− 13
− 14
5-9.3 Failure diagnosis for the thermopile (HIKARI i-see Sensor)
3. Outline and detected temperature of the thermopile
• 2 kinds of temperature information (voltage) are output from the thermopile.
Vtamb: Temperature information about the thermopile itself ( ambient temperature)
Vtobj: Temperature information about the object to be detected by the thermopile (infrared ray)
Each output changes between 0 V ~ 5 V.
Temperature information (voltage) about the object to be detected by the thermopile varies depending on the temperature of the thermopile itself.
Even if the temperature of the object stays constant, the values of temperature information about the object (Vtobj) will be various if the temperature of the thermopile itself varies.
• The following chart shows rough standards of the output voltage of thermopile
Temperature Information about the object according to the ambient temperature (Vtobj: unit: V)
Each voltage value is a representative value as a guide.
Values of Vtobj in the following chart are output when the object is placed under the entire field of view of the thermopile.
Ambient temperature( )
Vtamb(V)
Temperature of the object( )
0
5
10
15
− 20
− 15
− 10
− 5
20
25
30
− 20
1.077
2.225
2.498
2.79
3.1
3.43
3.779
4.148
4.538
4.949
-
-
− 10
1.298
1.66
1.933
2.225
2.535
2.865
3.214
3.583
3.973
4.384
4.817
-
0
1.565
1.02
1.294
1.585
1.896
2.225
2.574
2.943
3.333
3.744
4.177
4.631
10
1.879
0.302
0.575
0.867
1.177
1.507
1.856
2.225
2.615
3.026
3.458
3.913
20
2.24
-
-
0.066
0.376
0.706
1.055
1.424
1.814
2.225
2.657
3.112
30
2.647
-
-
-
-
-
0.168
0.537
0.927
1.338
1.771
2.225
Vtobj(V)
E.g.) The object at about 5 is measured at the ambient temperature of –10 .
Vtamb: approx. 1.298V, Vtobj: approx. 3.214V
9.5
max.
9.15
8.15
0.1 max. gap
4.2 ± 0.2
2.5 max.
1.1 ± 0.2
4.2 ± 0.3
0.1 max. gap
8.2 ± 0.3
14 ± 0.3
12.5 ± 0.3
3.5
3
2.5
2
1.5
5.5
5
4.5
4
1
0.5
0
-30
VTamb:1.08V
VTamb:1.57V
VTamb:2.65V
-20
4.8
11.3
6.5 ± 0.2
VTamb:1.30V
VTamb:1.88V
-10 0 10 20
Temperature of the object
30 40 50
46
60
6 NAMES OF THE PARTS
MR-E55R-C
MR-E60R-C
Operation panel
Refrigerator compartment
AUTO-shelf
Two-way flexishelf
ICE SELECT button
Supercool freezing button
SELECT/QUICK button
ROOM button
Change pocket (small)
Small item case
Bottle pocket (small)
Rotating partition
Do not close the door with the rotating partition turned up.
Free egg shelf
Water tank
Automatic ice maker
(Ice making compartment)
Freezer compartment
Freezing case
(top)
Interior LED
Change pocket (large)
BLUE LED
Turns off if the LED stay lit for 5 minutes
Lid of slide chilled case
Slide chilled case
Bottle pocket (large)
Versa compartment
Versa compartment is applicable to freezer and soft freezing,
Versa compartment is set to soft freezing mode at factory shipping.
Aluminum tray
Food is cooled quickly due to pre-coold tray
Adjustable partition
Vegetable compartment
Slide case
Water supply pipe
Freezing case (bottom)
For freezing only
Freezable 500 ml PET bottles can be placed in upright.
LEDs (ceiling area)
Water supply port cap
Water tank lid
Pipe
Water supply pump,
Light-type bacteria removing filter
Water tank (app. 1.2L)
V-LED lamp
Irradiate light-type bacteria removing filter to prevent the bacteria from being bred in the water tank.
Vegetable case
2L PET bottles can also be stored
HIKARI i-see sensor
(Infrared sensor, blue LED)
Senses positions and temperatures of foods.
Ice tray
Cannot be removed
Soundproof mat
Reduces the sound of ice dropping into the storage bin.
Do not discard it.
Ice storage box
Ice server
47
7
DISASSEMBLY INSTRUCTIONS
MR-E55R-C
MR-E60R-C
Plug out before work!!
Check the automatic ice-maker pressing ice making stop switch.
When assembling & disassembling parts seven kinds of screws and rivets are used. Do not mistake to use them.
4 12
Stainless steel
4 12 (Black)
With metal washer
4 16 (White)
With plastic washer
Specified screw Rivet
Rivet
OPERATING PROCEDURE
1. Parts inside the refrigerator compartment: AUTOshelf
(1) Remove two-way flexishelf from the refrigerator compartment.
AUTO-shelf
Move the lever to the right, and slide the AUTO-shelf to the uppermost position. (See photo 1)
Push the catches (4 places) inward, and remove the AUTOshelf from the metal stoppers. Lift up and remove the AUTOshelf toward you. (See photo 2)
Remove the metal stoppers in front, back, left, and right sides of the unit.
Caution on assembly
First, install the metal stoppers to the unit. Then, place the
AUTO-shelf on top, and push the AUTO-shelf downward until it clicks into place (4 places). Refer to photos 3, 4 for the direction of the metal stopper installation.
Photo 1
Catches
Catches
PHOTOS
Levers Two-way flexshelf AUTO-shelf
Ceiling of slide chilled compartment
Catches
Catches
Photo 2
Photo 4
Metal stopper
AUTO-shelf
Catch
Metal stopper
Photo 3
Metal stopper
48
OPERATING PROCEDURE
Removing the AUTO-shelf from the AUTO-shelf frame.
Remove the catches in the back (3 places), and lift up the
AUTO-shelf as shown in photo 6. (See photos 5, 6)
The catches in front (4 places) will detach. Pull the AUTO-shelf toward you to remove.
Photo 5
PHOTOS
AUTO-shelf frame
AUTO-shelf
Photo 6
Catch Catch
Catch
AUTO-shelf AUTO-shelf frame
2. Parts inside the refrigerator compartment: Vertical partition Right rail of the slide compartment Left rail of the slide compartment Interior LED (right and left) Cover (Control panel) Control panel,
Duct R Deodorizing unit and thermistor attachment
(1) Remove the AUTO-shelf and two-way flexishelf from the refrigerator compartment.
Vertical partition
Remove the small item case and the slide chilled case.
Pull out the ceiling by unhooking the front catches on both sides.
Remove the slide chilled case lid.
Remove the vertical partition.
Ceiling of slide chilled compartment
Small item case
(with free egg
shelf (S))
Slide chilled case lid
Photo 7
Photo 8
Slide chilled case
Vertical partition
Right rail of the slide compartment
(2) Slide the right rail out toward you. (See photo 7)
Left rail of the slide compartment
(3) Remove the screw at the left rail of the slide compartment, and slide the left rail toward you. (See photo 8)
Screw
Control panel
Right rail of the slide compartment
Left rail of the slide compartment
Control panel
49
OPERATING PROCEDURE
Interior LED (right and left)
Removing
Remove the screw on the right or left LED. (See photo 9)
Slide upward the right or left interior LED while pushing up the bottom, and pull toward you to remove.
Note:
If the interior LED is too stiff to slide upward and to remove by hand, place a piece of board at the bottom of the LED, and gradually tap the board in the sliding direction shown to remove the LED.
Photo 9
PHOTOS
Interior LED (Left)
Screw
Cover (Control panel)
(4) Remove the catches while pushing the catches at sides of the control panel, and remove the tabs in order of bottom, top. (See photo 10)
Control panel Duct R
(5) Remove rivet , and pull out the mirror hinge on the lower left of the control panel to remove the connector. (See photo 10)
(6) Remove rivet (2 rivets) in the upper left and right side, screw
(1 screw) on the lower left side.
Detach catches (5 places). (See photo 10)
Photo 10
Rivet
Screw
Catch
Catch
Catches
Catch
Catch
Rivet
Cover (Control panel)
Catch
Control panel
Mirror hinge
Catches Deodorizing unit & thermistor attachment
(7) Remove screws (3 screws), the catch (1 place), and the connector. (See photo 11)
Control panel assembly
(The assembly consists of the following: control panel, and duct R).
Photo 11
Rivet
Catch
Deodorizing unit & thermistor attachment Caution on assembly
To prevent poor contact of connectors, connect them properly.
Fix the control panel by inserting the lower catches (2 places) into the bottom of refrigerator compartment.
Screws
50
OPERATING PROCEDURE
3. Parts inside the versa compartment : I-see sensor
Versa compartment ceiling with deodorizing filter
(1) Remove the parts in the versa compartment.
(2) Slide the two-way flexishelf toward you.
I-see sensor
(3) Remove the screw (1 screw) and the connector.
(See photo 12, 13)
Versa compartment ceiling with deodorizing filter
(4) Remove rivets (2 rivets) and pull down the ceiling.
(See photo 14, 15)
Caution on installation
Push the parts firmly into place with no clearance around the parts.
Photo 12
Photo 13
PHOTOS
I-see sensor
Screw
Versa compartment
Supercool freezing LED
Connector
I-see sensor
Photo 14
Rivet
I-see sensor
Rivet
Versa compartment ceiling
Photo 15
Deodorizing filter
Versa compartment ceiling
51
OPERATING PROCEDURE
4. Parts inside the ice making compartment, versa compartment, vegetable compartment, and freezer compartment :
Photo 16
PHOTOS
S Cover (IM) Automatic ice maker assembly Cover
(upper) Fan grille Evaporator Defrost heater, Drip tray, DEF thermistor Vegetable compartment ceiling
Connector cover V Vegetable compartment LED
Vegetable compartment thermistor
(1) Remove interior parts out of ice making compartment, versa compartment, vegetable compartment, and freezer compartment.
(2) To detach them, pull out the doors of ice making compartment, versa compartment, vegetable compartment, and freezer compartment.
Photo 17
Parttition S
Catches
Screws
Partition I
(3) Lift the partition I to remove.
A r r o w Partition S
(4) Remove the catches (4 places) with a flat-blade screwdriver.
(See photo 16)
Partition I/ S cover
(5) Remove screw (2 screws) at the front of the refrigerator and
4 rollers. Remove the catches at the both sides of partition
I/S cover. (Remove them with a driver or another tool which is wrapped in cloth in order to protect the cover surface from scratches.) (See photo 17)
Photo 18
Screw
Catch
Rollers
Catch
Catch
Partition I/S cover
Rollers
Partition I/S
Partition I/ S
(6) Remove the catches on the upper and lower right of the partition I/S (see photo 18), and then slide the partition I/S toward right while being careful not to deform or damage the pipe.
(See photo 19)
Deforming or damaging the partition I/S causes refrigerant leakage or failure of cooling.
Photo 19
Pipe
Caution on assembly
Do not deform or damage the pipe. (See photo 18)
Deforming or damaging the pipe causes refrigerant leakage or failure of cooling.
Install the partition I/S so that the arrow points up.
(See photo 17)
Partition I/S
Move to right
52
OPERATING PROCEDURE
Cover (IM)
(7) Remove catches (3 places) in order to detach the cover. (See photo 20)
Automatic ice maker assembly
(8) Remove pressing catches (2 places) upward, and pull automatic ice maker assembly to the right side. (See photo 20)
Cover (upper)
(9) Remove rivet (1 rivet) to remove the cover from the fan grille. (See photo 21)
Fan grille
(10) To remove the fan grille, remove the screws (4 screws) on the right, left, bottom, the lower catches (3 places), and the connectors (4 connectors) in the connector area (See photo
21) on the upper left. (See photo 22)
Note
After removing the fan grille, attach the lead wire on the side of the refrigerator with a tape to protect it from getting wet with evaporator condensation.
Fan grille consists of the following: motor dampers (for ice- making compartment/ refrigerator compartment, versa compartment/vegetable compartment), refrigerator fan motor, fan, thermal fuse, and 3 thermistors. (See photo 22)
Photo 20
Photo 21
Pipe
PHOTOS
Tank holder
Cover (IM)
Catches
Catches
(Automatic
Ice maker
assembly)
Automatic
Ice maker assembly
Rivet
Cover (upper)
Connector area
Fan grille
Photo 22
Screws Screws
Fan grille
Catches
Fan grille
(Fan grille consists of the following: motor dampers (for ice making compartment/refrigerator compartment, versa compartment/vegetable compartment), refrigerator fan motor, fan, thermal fuse, and 3 thermistors).
53
OPERATING PROCEDURE PHOTOS
Evaporator
(11)
Remove the 4-pin connector that is stowed in the contoured section of main refrigerator housing.
Detach the brazed section of piping. Remove the catch protruding from the contoured section of main refrigerator housing to remove the evaporator. (See photo 23, figure 1, 2)
Photo 23
DEF thermistor
Brazed section
Evaporator
Figure 2
Defrost heater 2
Installation:
Attach the evaporator to the catch protruding from the main refrigerator housing. (See figure 1, 2)
Check both the entry side (black tube) and the exit side (gray tube) of the evaporator. Braze the entry side to the pipe with black marking, leading from the main refrigerator housing; and the exit side to the other pipe.
Exit side
Evaporator outlet pipe
Gray tube
Unit outlet pipe
No marking
30
Entry side
Evaporator inlet pipe
Black tube
Unit inlet pipe
With marking
Figure 1
Heater roof Defrost heater 1
Evaporator
Catch to fix the evaporator
Catch to fix the defrost heater
The refrigerant flows in the muffler from top to bottom. The pipe from the evaporator exit leads to the top of the muffler. The pipe from the muffler (gray tube) leads to the no-marking unit outlet pipe.
Connect the connector leading from the evaporator to the connector on the contouring section of main refrigerator housing.
Stow the lead wires in the contouring section and cover it with seal tape.
Figure 2
Pull the evaporator up in the direction of arrow
A to detach it from the catch.Slide the defrost heater out in the direction of arrow B.
Evaporator
Catch to fix the evaporator
Catch to fix the defrost heater
54
OPERATING PROCEDURE PHOTOS
Defrost heater Drip tray Figure 3
(12) Detach the defrost heater from the catch on the main refrigerator housing. Slide the defrost heater out towards you.
Remove the defrost heater from the heater roof. (See figure 3)
Remove the aluminum tape, then the drip tray. (See figure 4)
Heater roof
Defrost heater 1
Installation:
Attach the drip tray so that it closely fits into the right place of the main refrigerator housing. (See figure 4)
Loosen the lead wires to prevent water from entering the glass tube. Make sure the orientation of the defrost heater is correct. (See figure 3)
Attach the defrost heater to the catch. Use the respective tabs to secure the 2 lead wires on the left and right side of main refrigerator housing. (See photo 24, 25)
Fix the lead wires to the main refrigerator housing with seal tape. (See photo 26)
Firmly connect the bullet terminal (right) with the defrost heater connector (left). Stow the lead wires in the contouring section of main refrigerator housing. Cover that section with seal tape. (Use the seal tape provided with the evaporator.)
(See photo 27)
Remove the defrost heater from the clips on the both ends of the heater roof.
The arrow C indicates the front side of the refrigerator.
Figure 4
Aluminum tape (4 sides)
Drip tray
Photo 26
Photo 24
Lead wire
Defrost heater 2
Defrost heater 1
Put 4 pieces of seal tape on the positions indicated in the picture above.
Photo 27
Defrost heater connector Seal tape
Defrost heater 2
Seal tape
Bullet terminal
Tab
Photo 25
Defrost heater 2
Lead wire
Tab
Defrost heater 1
Defrost heater Defrost heater 1 connector
Stow the bullet terminal (right) and defrost heater connector (left) in the contouring section. Cover it with seal tape.
55
OPERATING PROCEDURE
Defrost thermistor
(13)
Cut the nylon fastener and detach the defrost thermistor from the evaporator. (See photo 28)
The defrost thermistor and the evaporator pipe heater are connected to the 4-pin connector. Cut the lead wires of the defrost thermistor at the base of the 4-pin connector.
(See photo 29)
Photo 28
Installation:
Connect the replacement defrost thermistor to the evaporator connector. (See photo 30)
Secure the defrost thermistor to the muffler with 3 nylon fasteners (large) provided with the replacement defrost thermistor. Then, tie the lead wires of defrost thermistor and the evaporator pipe heater together with a nylon fastener (small).
(See photo 31, 32) (If they are attached to an incorrect position, thermal characteristics will be altered.)
Stow the evaporator defrost thermistor connector in the contouring section of main refrigerator housing. Cover the contouring section with seal tape. (Use the seal tape provided with evaporator.) (See photo 27)
Photo 29
PHOTOS
Cut the nylon fastener.
Photo 30
Replacement defrost thermistor
Photo 32
Replacement defrost thermistor
Connect the housing.
Photo 31
Muffler
As the picture shows, attach the thermistor to the muffler on the side which does not face the evaporator.
56
Nylon fastener (small)
Nylon fastener (large)
OPERATING PROCEDURE
Vegetable compartment ceiling
(14) Remove the rivets (3 rivets) to pull the ceiling toward you. (See photo 33)
Photo 33
Connector cover V
(15) Remove the rivet (1 rivet). (See photo 34)
Vegetable compartment LED
(16) Remove the screw (1 screw) (See photo 35)
Vegetable compartment thermistor
(17) Remove the screw (1 screw) and the catch (1 place). (See photo 36)
Photo 34
Rivet
PHOTOS
Rivet
Vegetable compartment ceiling
Rivet
Rivet Connector cover V
Photo 35
Screw
Vegetable compartment LED
Photo 36
Vegetable compartment ceiling
Catch
Screw
Vegetable compartment thermistor
Vegetable compartment ceiling
57
OPERATING PROCEDURE
5. Parts inside the refrigerator compartment Left rail of the slide compartment Parts inside the ice making compartment Ice making compartment door
Tank holder Door switch
(1) Remove the parts inside the refrigerator compartment.
(See procedure [1])
(2) Remove the left rail of the slide compartment.
(See procedure [2])
(3) Remove the parts inside the ice making compartment.
(4) Remove the ice making compartment door.
Photo 37
Tank holder
Tank holder
(5) Remove a screw on the side of the refrigerator compartment.
(6) Loosen screw (3 screws) halfway on the side of the ice making compartment. Put a screwdriver on the head of each screw and tap the bottom side of the holder softly to detach it.
(See photo 37)
(7) Lift up the tank holder from the refrigerator compartment to remove it.
Note:
Put the lead wires in place so that they do not get caught in water supply hole.
Put the tank holder in place so that the water does not leak from it.
Figure 5
Door switch
(8) Insert a flat-blade screwdriver between the switch and the body to remove the door switch.
6. Operation panel
Photo 38
How to remove
(1) Slide the operation panel in the direction of the arrows, until it stops. (See photo 38)
(2) Pull out the operation panel as shown in photo 39.
(See photo 39)
Note:
Please pull it out carefully because it is still wired to the body.
(3) Take out the panel by detaching the connector of lead wires from the body.
Note:
If the horizontal slide is hard to remove with hands, put plate on the right edge of the panel (please put protective object such as tapes on the area of contact on the door panel and the operation panel), and gently tap it in the sliding direction.
Photo 39
PHOTOS
Pipe
Screw
Sliding direction
Door switch
Tank holder
Operational panel
58
OPERATING PROCEDURE PHOTOS
7. Rotational heater board
(1) Remove 4 fixing screws to remove the rotational heater board.
(See photo 40)
(2) Remove a screw on the wiring cover and disconnect the connector in the cover. (See photo 40)
Caution on assembly
When raising the rotational heater board, replace the rotational heater board as it was. If the refrigerator door is closed with the board raised, the rotational heater board may hit against the left door of refrigerator and be damaged.
Though the anti-condensation heater may make rotational heater board hot, it does not affect food inside.
Refer to the right figure when installing the rotational heater board. (See figure 6)
Loosen the fixing screw and adjust a vertical (upper and lower) motion.
After assembling, make sure that the rotational heater board fits the guide properly and works properly.
Photo 40
Screws
Wiring cover
Screw
(Wiring cover)
Rotational heater board
Figure 6
Screws
Rotational heater
Guide board 3 2mm
Left door of refrigerator compartment (4)mm
8. Leg cover
Removing
Remove the leg cover by sliding back and forward.
Installing
After adjusting the casters, install the leg cover by sliding back and forward.
Before installing the leg cover, be sure to adjust the casters.
Photo 41
Catch
Casters
Leg cover Catch
59
OPERATING PROCEDURE
9. Compressor cover Elect cover Control board
Drain pan Reactor Box fan
Compressor cover
(1) Remove 8 screws for compressor cover at the back of the refrigerator. (See photo 42)
Elect cover
(2) Remove the fixing screws (3 screws) and the rivet (1 rivet) on the elect cover on the back of the refrigerator. (See photo 43)
Control board
(3) Remove the control board by removing the connector and the fixing screws of the lead wires.
Photo 42
Photo 43
Screw
PHOTOS
Screws
Screws
Rivet
Compressor cover
Screw
Caution on installation
To prevent pinching of the lead wires and poor insertion of the connector, be sure to install the lead wires and connectors in the appropriate positions.
Drain pan
(4) Remove screw (1 screw). (See photo 44)
Caution
Wash the drain pan with water in case it is dirty.
(5) Remove the drain pan while bending upward the wiring inside the drain pan.
Note:
Avoid bending or crushing the piping.
Reactor
(6) Remove the screws (2 screws). (See photo 45)
(7) Remove the reactor by removing the holders (2 positions) and the connector. (See photo 46)
Box fan
(8) Remove the connector.
(9) Pull out the box fan by removing the fixing screw (1 screw) (See photo 44) and the connector.
Photo 44
Reactor
Compressor
Photo 45
Elect cover
Box fan
Screw
(Drain pan)
Screw (Box fan)
Drain pan
Screws
Reactor
Photo 46 Connector Holder
Holder
60
Figure 7
W
W
W
W
Dryer holder
Charge pipe
(High pressure side)
W
Dryer
W
OPERATING PROCEDURE
Piping connection of three-way valve Attach U washer as shown in the figure below.
Inlet
Outlet
Three-way valve
W
W
: This mark shows welded point.
Charge pipe
(Low pressure side)
Reactor
W
W
W
E50: PEFI100E
W
W
W
W
Compressor
W W W Box fan
Adjust piping and secure clearance of about 10 to 15 mm around pipes.
Make sure clearance is secured especially between the following parts.
Between charge pipe and compressor cover, bottom pan, compressor,
or discharge pipe.
Between suction pipe and compressor cover or capillary tube.
Between capillary tube and three-way valve or lead wires.
61
Door adjustment
<Adjusting refrigerator compartment doors>
• Common elements
First, check the installation condition.
If the adjustment bolt is not in contact with the floor, lower the bolt, and adjust it so that the caster is slightly above the floor.
When the refrigerator is installed in the corner of the room, the bolt of the refrigerator may sink into the floor and cause the refrigerator to tilt. It is recommended to make adjustments by objects like boards beforehand.
When the refrigerator bolt sinks into the floor, and it can be confirmed visually, prevent sinking by using objects like boards.
Note: The refrigerator weighs about 100 kg, and is held by 4 bolts. How far each bolt sinks into the floor depends on factors such as floor pillars. Change in balance due to position of stored food (such as large or small amount of food stored in the door pockets) may also affect sinking.
<Adjusting ice making compartment and versa compartment doors>
Adjusting doors horizontally
Adjusting vertical space between doors
Too much space Not enough space
B
A
B
A
A > B (More space in outer side)
Or
A < B (More space in inner side)
Place spacer set under the outer roller of the tilted door
(ice making compartment door in the above illustration) to
Place spacer set under the inner roller of the tilted door
(ice making compartment door in the above illustration) to
Marking
Right 0.5 [09]
Right 1.0 [11]
LH
A > B (Too much space between the ice making compartment and versa compartment doors.)
Misaligned versa compartment door
Misaligned ice making compartment doors
Replace roller set of the right and left versa compartment doors.
a To adjust about 0.5 mm replace
with roller set C.
b To make large adjustment replace
with roller set D.
Replace lower roller set of the ice making compartment door.
c To adjust about 0.5 mm replace
with roller set A.
d To make large adjustment replace
with roller set B.
RH
Marking
Right 0.5 [10]
Right 1.0 [12]
A < B (Small space between the ice making compartment and versa compartment doors.)
Misaligned versa compartment door
Misaligned ice making compartment door
Replace roller set of the right and left versa compartment doors.
a To adjust about 0.5 mm replace
with roller set A.
b To make large adjustment replace
with roller set B.
Replace lower roller set of the ice making compartment door.
c To adjust about 0.5 mm replace
with roller set C.
d To make large adjustment replace
with roller set D.
Identifying roller sets (Marking)
Roller set A (0.5 mm to the right)
LH
09
Roller set B (1.0 mm to the right)
Roller set C (0.5 mm to the right)
Roller set D (1.0 mm to the right)
11
13
15
RH
10
12
14
16
Check points after adjustment
When adjustments such as hinge position have been made without food in the door pockets, confirm the door position again with food stored inside.
When the refrigerator is moved to make adjustments in the back bolts, floor may be damaged due to objects trapped in the caster. It is recommended to take preventive measures such as cleaning around the refrigerator and covering the floor with boards before moving the refrigerator.
After adjusting the refrigerator compartment doors, confirm auto closer operation.
HEAD OFFICE: TOKYO BLDG., 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
Copyright 2010 MITSUBISHI ELECTRIC ENGINEERING CO., LTD.
Distributed in Dec. 2010 No. OAH110 7
Made in Japan
New publication, effective Dec. 2010
Specifications subject to change without notice
Prenesi
Oglas