DR Power Equipment RapidFire Pro Safety & Operating Instructions Manual
Advertisement
Advertisement
DR
®
RAPIDFIRE™ LOG SPLITTER
SAFETY & OPERATING INSTRUCTIONS
Shown with optional
Tray Kit Accessory
Serial No.
Order No.
Original Language
DR Power Equipment
Toll-free phone: 1-800-DR-OWNER (376-9637)
Fax: 1-802-877-1213
Website: www.DRpower.com
Read and understand this manual and all instructions before operating the DR RAPIDFIRE LOG SPLITTER.
Table of Contents
Chapter 1: General Safety Rules ............................................................................................................................................................ 3
Chapter 2: Setting Up The DR RAPIDFIRE LOG SPLITTER ................................................................................................................. 7
Chapter 3: Operating The DR RAPIDFIRE LOG SPLITTER .................................................................................................................. 12
Chapter 4: Maintaining The DR RAPIDFIRE LOG SPLITTER .............................................................................................................. 15
Chapter 5: Troubleshooting .................................................................................................................................................................. 22
Chapter 6: Parts Lists and Schematic Diagrams .................................................................................................................................. 24
Conventions used in this manual
This indicates a hazardous situation, which, if not avoided, could result in death or serious injury.
This indicates a hazardous situation, which, if not avoided, could result in minor or moderate injury.
This information is important in the proper use of your machine. Failure to follow this instruction could result in damage to your machine or property.
Serial Number
Label
Figure 1
Serial Number and Order Number
A Serial Number is used to identify your machine and is located on the Serial
Number Label on your machine ( Figure 1 ). An Order Number is used to check and maintain your order history and is located on the upper left portion of your packing slip. For your convenience and ready reference, enter the Serial
Number and Order Number in the space provided on the front cover of this manual.
Additional Information and Potential Changes
DR Power Equipment reserves the right to discontinue, change, and improve its products at any time without notice or obligation to the purchaser. The descriptions and specifications contained in this manual were in effect at printing. Equipment described within this manual may be optional. Some illustrations may not be applicable to your machine.
2 DR ®
RAPIDFIRE™ LOG SPLITTER
Chapter 1: General Safety Rules
Read this Safety & Operating Instructions manual before you use the DR RAPIDFIRE LOG SPLITTER. Become familiar with the operation and service recommendations to ensure the best performance from your machine. If you have any questions or need assistance, please contact us at www.DRpower.com or call toll-free 1-800-DR-OWNER (376-9637) and one of our Technical
Support Representatives will be happy to help you.
Labels
Your DR RAPIDFIRE LOG SPLITTER carries prominent labels as reminders for its proper and safe use. Shown below are copies of all the Safety and Information labels that appear on the equipment. Take a moment to study them and make a note of their location on your LOG SPLITTER as you set up and before you operate the unit. Replace damaged or missing safety and information labels immediately.
#32128
#18887
#25044
#13758
#33361
#36545
CONTACT US AT www.DRpower.com
3
Protecting Yourself and Those Around You
This is a high-powered machine, with moving parts operating with high energy. You must operate the machine safely. Unsafe operation can create a number of hazards for you, as well as anyone else in the nearby area. Always take the following precautions when using this machine:
Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people, their property, and themselves.
Always wear protective goggles or safety glasses with side shields while using the Log Splitter to protect your eyes from possible thrown debris.
Avoid wearing loose clothing or jewelry, which can catch on moving parts.
We recommend wearing gloves while using the Log Splitter. Be sure your gloves fit properly and do not have loose cuffs or drawstrings.
Wear shoes with non-slip treads when using your Log Splitter. If you have safety shoes, we recommend wearing them. Do not use the machine while barefoot or wearing open toed sandals.
Wear long pants while operating the Log Splitter.
Use ear protectors or ear plugs rated for at least 20 dba to protect your hearing.
Keep bystanders at least 50 feet away from your work area at all times. Stop the engine when another person or pet approaches.
Safety for Children and Pets
Tragic accidents can occur if the operator is not alert to the presence of children and pets. Children are often attracted to the machine and the splitting activity. Never assume that children will remain where you last saw them. Always follow these precautions:
Keep children and pets at least 50 feet from the working area and ensure they are under the watchful care of a responsible adult.
Be alert and turn the machine off if children or pets enter the work area.
Never allow children to operate the Log Splitter.
Towing
ALWAYS check before towing to make certain your Splitter is correctly and securely attached to the towing vehicle. Be sure that the ball hitch you are using is the proper size for the hitch coupler on the machine. Be sure the safety chains are properly hooked to the vehicle leaving enough slack for turning.
ALWAYS secure the rack to the beam before towing.
ALWAYS use accessory lights and devices when transporting on a road or highway to warn operators of other vehicles. Check your local government regulations for DOT information.
ALWAYS allow for added length of the Splitter when turning, parking, crossing intersections, and in all driving situations.
ALWAYS be careful when backing up. You could jackknife your Splitter if care is not taken.
NEVER exceed 45 mph. when towing your Splitter. Obey all state and local regulations when towing on state and local roads and highways. Adjust your speed for terrain and conditions, as needed. Be extra cautious when towing over rough terrain, especially over a railroad crossing.
NEVER allow anyone to sit or ride on your Splitter.
NEVER carry any cargo on your Splitter.
Do travel slowly over rough terrain, on hillsides, and around curves to prevent tipping.
Do not tow the Splitter near the edge of a ditch or excavation.
4 DR ®
RAPIDFIRE™ LOG SPLITTER
Safety with Gasoline - Powered Machines
Gasoline is a highly flammable liquid. Gasoline also gives off flammable vapor that can be easily ignited and cause a fire or explosion. Never overlook the hazards of gasoline. Always follow these precautions:
Never run the engine in an enclosed area or without proper ventilation as the exhaust from the engine contains carbon monoxide, which is an odorless, tasteless, and deadly poisonous gas.
Store all fuel and oil in containers specifically designed and approved for this purpose and keep away from heat and open flame, and out of the reach of children.
Replace rubber fuel lines and grommets when worn or damaged and after 5 years of use.
Fill the gasoline tank outdoors with the engine off and allow the engine to cool completely. Don't handle gasoline if you or anyone nearby is smoking, or if you're near anything that could cause it to ignite or explode. Reinstall the fuel tank cap and fuel container cap securely.
If you spill gasoline, do not attempt to start the engine. Move the machine away from the area of the spill and avoid creating any source of ignition until the gas vapors have dissipated. Wipe up any spilled fuel to prevent a fire hazard and properly dispose of the waste.
Allow the engine to cool completely before storing in any enclosure. Never store a machine that has gas in the tank, or a fuel container, near an open flame or spark such as a water heater, space heater, clothes dryer or furnace.
Never make adjustments or repairs with the engine running. Shut down the engine, disconnect the spark plug wire, keeping it away from the spark plug to prevent accidental starting, wait 5 minutes before making adjustments or repairs.
Never tamper with the engine’s governor setting. The governor controls the maximum safe operation speed and protects the engine. Over-speeding the engine is dangerous and will cause damage to the engine and to the other moving parts of the machine. If required, see your authorized dealer for engine governor adjustments.
Keep combustible substances away from the engine when it is hot.
Never cover the machine while the muffler is still hot.
Do not operate the engine with the air cleaner or the carburetor air intake cover removed. Removal of such parts could create a fire hazard. Do not use flammable solutions to clean the air filter.
The muffler and engine become very hot and can cause a severe burn; do not touch.
General Safety
Operating this Log Splitter safely is necessary to prevent or minimize the risk of death or serious injury. Unsafe operation can create a number of hazards for you. Always take the following precautions when operating this Log Splitter:
Your Log Splitter is a powerful tool, not a plaything. Exercise extreme caution at all times. The machine is designed to split logs. Do not use it for any other purpose.
Know how to stop the Log Splitter quickly; see “stopping the engine” in chapter 3.
Never operate your unit on a slippery, wet, muddy, or icy surface. Exercise caution to avoid slipping or falling.
See manufacturer’s instructions for proper operation and installation of accessories. Only use accessories approved by DR
Power Equipment.
Never use the machine without ensuring that all guards and shields are in place.
Never, under any conditions, remove, bend, cut, fit, weld, or otherwise alter standard parts on the Log Splitter. This includes all shields and guards. Modifications to your machine could cause personal injuries and property damage and will void your warranty.
Allow only one person to operate the Log Splitter at any time.
CONTACT US AT www.DRpower.com
5
General Safety (continued)
If the machine should start making an unusual noise or vibration, shut down the engine, disconnect the spark plug wire, keeping it away from the spark plug to prevent accidental starting, wait 5 minutes for machine to cool down, then inspect for damage. Vibration is generally a warning of trouble. Check for damaged parts and clean, repair and replace as necessary.
Never tamper with safety devices. Check their proper operation regularly.
Before performing any maintenance or inspection procedure on the Log Splitter shut down the engine, disconnect the spark plug wire keeping it away from the spark plug to prevent accidental starting, wait 5 minutes for machine to cool down.
Never allow people who are unfamiliar with these instructions to use the Log Splitter. Allow only responsible individuals who are familiar with these rules of safe operation to use your machine.
Never overload or attempt to split logs beyond the recommendations listed in this manual. Personal injury or damage to the machine could result.
While using the Log Splitter, don't hurry or take things for granted. When in doubt about the equipment or your surroundings, stop the machine and take the time to look things over.
Never operate the machine when under the influence of alcohol, drugs, or medication.
Use the machine only in daylight.
Stay alert for hidden hazards or traffic.
Keep all nuts and bolts tight and keep the equipment in good operating condition.
California Proposition 65
California Proposition 65:
Engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects, and other reproductive harm.
This product contains or emits chemicals known to the State of California to cause cancer, birth defects, and other reproductive harm.
A Note to All Users
Under California law, and the laws of some other states, you are not permitted to operate an internal combustion engine using hydrocarbon fuels without an engine spark arrester. This also applies to operation on US Forest Lands. All DR RAPIDFIRE LOG
SPLITTERS shipped to California, New Mexico and Washington State are provided with spark arresters. Failure of the owner or operator to maintain this equipment in compliance with state regulations is a misdemeanor under California law and may be in violation of other state and/or federal regulations. Contact your State Park Association or the appropriate state organization for specific information in your area.
No list of warnings and cautions can be all-inclusive. If situations occur that are not covered by this manual, the operator must apply common sense and operate this DR RAPIDFIRE LOG SPLITTER in a safe manner. Contact us at www.DRpower.com or call
1-800-DR-OWNER (376-9637) for assistance.
6 DR ®
RAPIDFIRE™ LOG SPLITTER
Chapter 2: Setting Up The DR RAPIDFIRE LOG SPLITTER
It may be helpful to familiarize yourself with the controls and features of your DR RAPIDFIRE LOG SPLITTER as shown in Figure 2 before beginning these procedures. If you have any questions at all, please feel free to contact us at www.DRpower.com.
DR RAPIDFIRE LOG SPLITTER Controls and Features
Throttle
Lever Flywheels
Belts
Engagement
Handle
Fuel Shut-off
Choke
Lever
Belt Guard
Safety Interlock
Lever
Ram
Splitting Wedge
Cradle or optional
Tray (shown)
Gas Fill
Starter Cord Engine
Mount/Belt
Tensioner
Pneumatic
Tires
Ignition Switch
Off
Key Switch Off
Run
Start
On
Manual Start Electric Start
Support
Leg
Tow Hitch
Figure 2
CONTACT US AT www.DRpower.com
7
Specifications
Engine
RapidFire Pro
DR 5.8hp (see engine manual for specifications)
RapidFire Pro-XL (manual start) RapidFire Pro-XL (elec. start)
B&S, 9.50 CR (see engine manual for specifications)
B&S, 9.50 XR Subaru 6hp
(see engine manual for
Wedge Height
Log Capacity Length 24 inches, Diameter
30 inches*
Length 24 inches, Diameter 30 inches*
Length 24 inches, Diameter
30 inches*
Cycle Time
Tires
3 seconds (approx.)
16" 16" 16"
Beam Height
Overall Height
Overall Length w/ Tray
26" 26" 26"
48.3" 48.3" 48.3"
100.9" 100.9" 100.9"
Overall Length w/out Tray 83.5" 83.5" 83.5"
Width 46.8" 46.8" 46.8"
Splitter Weight w/ Tray 395 lbs. (179kg)
Splitter Weight w/out Tray 363 lbs. (165kg)
Flywheel Weight 55 lbs. (34kg)
Flywheel Diameter
Flywheel Max RPM
435
403
lbs. (197kg)
lbs. (183kg)
74 lbs. (34kg)
440
408
lbs. (200kg)
lbs. (185kg)
74 lbs. (25kg)
18-1/4" 18-1/4" 18-1/4"
400 RPM 400 RPM 400 RPM
*The diameter listed is indicative of the maximum suggested size - a small log can be difficult to split when it contains knots or a particularly tough fiber. On the other hand, it may not be difficult to split logs with regular fibers even if its diameter exceeds the maximum indicated above.
Assembling the DR RAPIDFIRE LOG SPLITTER
Tools and Supplies needed:
Utility Knife
Wire Cutters
Gloves
Two 9/16" Wrenches
2
Installing the Cradle Kit
Note: The Cradles are only needed if you did not purchase the Tray Kit. If you purchased a Tray Kit then skip the Cradle instructions and go to the “Installing the Tray Kit” section on page 9.
1
5
Figure 3
4
3
Parts Supplied in Cradle Kit ( Figure 3 ):
Qty
1 ............. 321041 ............ Bolt, Carriage, 3/8-16 X 1", GR5, ZP ..... 6
2 ............. 313601 ............ Cradle, Standard .................................... 2
3 ............. 313581 ............ Mount, Cradle........................................ 1
4 ............. 333511 ............ Bolt, Hex, Flange, 3/8-16 X 1.25" .......... 4
5 ............. 333331 ............ Nut, Nylon Lock, Flanged, 3/8-16 ......... 10
Compare the contents of the Cradle Shipping Box with the “Parts Supplied” list above. If you have any questions please contact us at www.DRpower.com or call
1-800-DR-OWNER (376-9637) for assistance.
1.
Open the Cradle Box using a Utility Knife.
2.
Cut the Straps that secure the Cradles together with Wire Cutters.
3.
Support the end of the Beam with a Jack Stand or equivalent to position the
Beam parallel with the ground.
8 DR ®
RAPIDFIRE™ LOG SPLITTER
4.
Install the Tow Bar to the end of the Beam with four 3/8-16 X 2.5 Bolts and
Lock Nuts (from the product package) using two 9/16" Wrenches ( Figure
4 ).
5.
Pull the Hitch Clip and Clevis Pin from the Leg and fold it to the down position. Align the holes and secure the Leg with the Clevis Pin and Hitch
Clip ( Figure 5 ).
6.
Remove the Jack Stand and lower the Splitter onto the Support Leg.
7.
Install the front Cradle Bracket to the end of the Beam with four Bolts and
Locknuts (from the cradle package) using two 9/16" Wrenches ( Figure 6 ).
8.
For easier alignment in the following step, slightly loosen the Side Bracket
Hardware using a 9/16" Wrench ( Figure 7 ).
9.
Install the Cradles to the front and side Brackets using three Carriage Bolts and Locknuts for each Cradle. Tighten all Cradle and Bracket hardware using a 9/16" Wrench.
Tow Bar
Figure 4
Bolts and
Lock Nuts
Hitch Clip and Clevis Pin
Installing the Tray Kit
Note: The following Tray Kit instructions only apply if you have purchased a
Tray Kit. If you did not purchase the Tray Kit, you have already installed the
Cradles as described in the previous section and can now continue to the
“Adding Oil and Gasoline” section on the next page.
Parts Supplied in Tray Kit ( Figure 8 ):
Qty
1 ............. 313631 ............ Table, Log (not shown) ......................... 1
2 ............. 321041 ............ Bolt, Carriage, 3/8-16 X 1", GR5, ZP ..... 4
3 ............. 333331 ............ Nut, Nylon Lock, Flanged, 3/8-16 ......... 4
4 ............. 150431 ............ Bolt, HHCS, 3/8-16 X 1-1/4", GR5 ........ 4
5 ............. 112411 ............ Washer, Flat, 5/16", USS, ZP ................ 4
6 ............. 180811 ............ Washer, Lock, 3/8" ................................ 4
Compare the contents of the Tray Kit with the “Parts Supplied” list above. If you have any questions please contact us at www.DRpower.com or call 1-800-DR-
OWNER (376-9637) for assistance.
Figure 5
Support
Leg
Front Cradle
Bracket
Bolts and
Locknuts
Figure 6
3
4 Cradles
Figure 8
2
6
5
Side
Bracket
Carriage Bolts and Locknuts
Figure 7
CONTACT US AT www.DRpower.com
9
Figure 9
Support
Leg
Figure 10
Hitch Clip and Clevis Pin
Bolts and Locknuts
Tray
Tray
Support
Leg
Bolts and
Locknuts
1.
Support the end of the Beam with a Jack Stand or equivalent to position the
Beam parallel with the ground.
2.
Install the Tow Bar to the Tray with four 3/8-16 X 2.5 Bolts and Lock Nuts
(from product package) using two 9/16" Wrenches ( Figure 9 ).
3.
Pull the Hitch Clip and Clevis Pin from the Leg and fold it to the down position. Align the holes and secure the Leg with the Clevis Pin and Hitch
Clip ( Figure 10 ).
4.
For easier alignment in the following step, slightly loosen the Side Bracket
Hardware using a 9/16" Wrench ( Figure 11 ).
5.
Position the Tray onto the Side Brackets and install the four Carriage Bolts and Locknuts (from the tray kit) by hand.
6.
Install the four Bolts, Lock Washers and Flat Washers (from the tray kit) to secure the Tray to the end of the Beam using a 9/16" Wrench ( Figure 12 ).
7.
Tighten all remaining Tray hardware using a 9/16" Wrench.
Adding Oil and Gasoline
Engine Oil See Engine Manual for specific Engine capacities and specifications
Fuel Unleaded gasoline
NOTE: Use only the recommended high detergent engine oil. Other types of oil could cause problems operating your machine. Please refer to your Engine Owner’s
Manual for detailed oil information.
Supplies Needed:
Clean Rag
Engine Oil
Figure 11
Side Brackets
The Engine must be level to get an accurate reading when adjusting the amount of oil. If the machine is not level, the oil level reading will not be accurate and may cause engine damage.
1.
Position the machine so the Engine is level. Remove the Oil Fill/Dipstick
( Figure 13 ) and clean the end of it with a rag.
Beam
Tray
Figure 12
Bolt, Lock Washer and Flat Washer
10 DR ®
RAPIDFIRE™ LOG SPLITTER
Figure 13
Oil
Check/Fill
2.
Machines are shipped with no oil . Initially add 16 oz. of the oil recommended by the Engine Manufacturer. Wait one minute for the oil to settle.
3.
Replace the Dipstick, but DO NOT screw it in to ensure an accurate reading and then remove it to check the oil level (clean the Dipstick with the clean rag after checking).
4.
Continue adding a few ounces of oil at a time, rechecking the Dipstick until the oil reaches the fill mark. Be careful not to overfill.
5.
Replace the Dipstick and screw all the way down when full.
6.
Remove the Gas Fill Cap and fill the Gas Tank with fresh, unleaded gas (with a minimum of 85 Octane) to approximately 1" to 1-1/2" below the top of the fill neck to allow for fuel expansion ( Figure 14 ). Be careful not to overfill.
Install the Gas Fill Cap before starting the engine. See your Engine Owner’s
Manual for more detailed information.
NOTE: To refill the gas tank, turn the engine OFF and let the engine cool at least five minutes before removing the gas fill cap.
Gas Cap
Figure 14
We highly recommend the use of fuel treatments in your fuel to prevent
Carburetor fouling.
Check the Tire Pressure
Tools Needed:
Tire Pressure Gauge
Air Compressor
1.
Remove the Valve Stem Protective Cap ( Figure 15 ) and check the tire pressure with a Tire Pressure Gauge.
2.
Check what the manufacturers recommended pressure is that is stamped on the side of the Tire.
3.
If the pressure is too low, add air through the Valve Stem with an air hose.
4.
Replace the Valve Stem Protective Cap when finished.
Figure 15
Do not over inflate the tires. Inflate to the manufacturers recommended pressure found on the tires.
Connect the Battery (electric start models)
1.
Connect the Black Negative Terminal onto the negative Battery Lug ( Figure
16 ).
Battery
Valve Stem
Protective Cap
Negative
Terminal
Figure 16
CONTACT US AT www.DRpower.com
11
Chapter 3: Operating The DR RAPIDFIRE LOG SPLITTER
It may be helpful to better familiarize yourself with the features of your Log
Splitter by reviewing Figure 1 in Chapter 2 before beginning the steps outlined in this chapter.
Operator
Zone
Operator
Zone
Read and understand all instructions, safety precautions, and/or warnings listed in “Chapter 1 General Safety Rules” before operating this
DR RAPIDFIRE LOG SPLITTER. If any doubt or question arises about the correct or safe method of performing anything found in this manual, please contact our Customer Service Representatives at our toll free number: 1-800-DR-OWNER (376-9637).
When operating the Log Splitter, make sure you are standing in the safe operating area (OPERATOR ZONE) as shown in F igure 17 . You must stay in the safe operating area at all times when the ram is in motion (whether extending or retracting). Never place any part of your body into a position that causes an unsafe operating condition.
Figure 17
Ignition Switch
Off
TOP VIEW
Throttle Control
Lever
Recoil Starter
Handle
Key Switch Off
Run
Start
Starting the Engine
Note: See the Engine Manual for more detailed and specific information on operating the Engine.
1.
Position your Log Splitter on flat, dry ground and chock the Wheels to prevent the Splitter from moving during use.
2.
Make sure the fuel shut-off valve is in the “ON” position ( Figure 18 ).
3.
Move the choke control lever to the CHOKE position to the left (should only be needed if the engine is cold).
4.
Move the throttle control lever to the FAST “Rabbit” position.
5.
Manual Start: Turn the Ignition Switch to the “On” position ( Figure 19 ).
Grasp the recoil starter handle and slowly pull until you feel resistance
( Figure 17 ). Let the cord retract a little bit then pull the cord rapidly to start the engine. One or two pulls usually starts the engine.
6.
Electric Start: Turn and hold the Key in the “Start” position until Engine starts then let the Key return to run position ( Figure 19 ).
7.
Move the choke control lever (if used for cold engine) slowly back to the
OPEN position (to the right) when the engine is running well ( Figure 18 ).
Note: If the Log Splitter has not been running (cold engine), warm up the engine by running the engine at half throttle for 3 to 4 minutes, then advance the engine throttle control to maximum speed.
Stopping the Engine
1.
Move the Throttle Lever to Idle “Turtle” position ( Figure 18 ).
2.
Manual Start: Turn the Ignition Switch to the “Off” position ( Figure 19 ).
3.
Electric Start: Turn the Key to the “Off” position.
On
Manual Start
Figure 19
Electric Start
12 DR ®
RAPIDFIRE™ LOG SPLITTER
Splitting
Note: All logs should be no longer than 24". Use the following photos for the correct and incorrect methods of splitting logs. Never split a log using an incorrect or unsafe method.
Do not place your hands on the ends of the log when loading the Log
Splitter. This is a very UNSAFE method and could result in injury to your hands ( Figure 20 ).
Do not reach or step across the beam while the Log Splitter is running.
This is a very UNSAFE method which could cause personal injury or even death.
Figure 20
Never attempt to split wood across the grain. The Log Splitter was not designed for cross-grain splitting. Doing so could damage the Log
Splitter and may cause personal injury ( Figure 21 ).
Make sure both ends of the log you are splitting are cut as square as possible. This will prevent the log from sliding out of position while under pressure ( Figure 22 ).
THE RAPIDFIRE LOG SPLITTER OPERATES DIFFERENTLY THAN A
HYDRAULIC SPLITTER. NOT OPERATING THE MACHINE PROPERLY WILL
RESULT IN DAMAGE TO THE MACHINE. ALWAYS FOLLOW THESE
NOTICES:
Do not be timid. A rapid movement of the Engagement Handle is necessary for the Rack and Pinion to engage and disengage fully without damage.
The Engagement Handle should never be stopped in any location between the fully forward or fully backward positions.
Do not hold the Handle in the forward position when the Ram stops moving forward. Always pull the Engagement Handle RAPIDLY to the back (Auto-Retract) position as soon as the Log is split or when the Ram is at the end of the stroke or when the Ram stops moving forward due to a tough log.
1.
Place the log on the Log Splitter. Grasp the log on the sides near the middle of the block ( Figure 23 ). Center the log, side-to-side, on the rail of the Log
Splitter, making sure that one end is against the Splitting Wedge.
Figure 21
Figure 22
The engagement Handle must be held fully forward against the hard stop when splitting. Failure to do so may result in kickback of the Handle.
Figure 23
Wood
Against
Wedge
Hands on
Sides of Wood
CONTACT US AT www.DRpower.com
13
Safety
Interlock
Lever
Figure 24
2
1
Engagement
Handle
2.
With one hand, lift and hold the Safety Interlock Lever up, then RAPIDLY press the Engagement Handle fully forward until it contacts the hard stop and hold firmly until the Log is split ( Figure 24 ).
3.
IMMEDIATELY AFTER the log is split, pull and hold the Engagement Handle to the Auto-Retract position to allow the Ram to return. If the Ram stops before the end of the stroke while splitting a tough log, quickly pull the
Engagement Handle back to the Auto-Retract position.
Splitting Tough Logs
If the Ram stops before the end of the stroke while splitting a tough Log, quickly pull the Engagement Handle back to the Auto-Retract position. Let the Ram return and allow the Flywheels to gain momentum for another full power split.
14 DR ®
RAPIDFIRE™ LOG SPLITTER
Chapter 4: Maintaining The DR RAPIDFIRE LOG SPLITTER
Regular maintenance is the way to ensure the best performance and long life of your machine. Please refer to this manual and the engine manufacturer's owner's manual for maintenance procedures. Service intervals listed in the checklist below supersede those listed in the engine manufacturer's owner's manual.
Before performing any maintenance procedure or inspection, stop the engine, wait five minutes to allow all parts to cool.
Disconnect the spark plug wire, keeping it away from the spark plug. Disconnect the Battery Terminals (Electric start only).
Regular Maintenance Checklist
P ROCEDURE
Check Engine Oil Level
Check General Equipment Condition
Perform Rail Maintenance
Check Belts
Grease Engagement Handle
Check Tire Pressure
Clean Engine Exterior and Cooling
Change Engine Oil
Replace Air Filter
Replace Spark Plug
B EFORE E ACH U SE E VERY 10 H OURS E VERY 25 H OURS E VERY 100 H OURS
▲
▲
▲
▲
1 st time 5 hours
▲
▲
▲
▲
▲
▲
Engine Service
Refer to the engine manufacturer’s manual for engine maintenance.
Lubrication
All Bearings of your Splitter are sealed units and should have sufficient lubricant to last the life of your machine with normal use. Perform machine lubrication per the following instructions.
Changing Engine Oil
One of the easiest methods to remove oil from this Engine is to use a siphon style Oil Extractor. If you do not have one you can purchase it from us at www.DRpower.com.
Tools and Supplies needed:
Clean Approved Container for used Oil
9/16" Wrench (Subaru)
10mm Wrench (DR)
1.
Place an approved Container under the Oil Plug.
2.
Remove the Oil Drain Plug with a 9/16" Wrench (Subaru) or a 10mm
Wrench (DR) to drain the Oil into the Container ( Figure 25 ).
3.
Reinstall the Oil Drain Plug.
4.
Add oil as described in “Adding Oil and Gasoline” in Chapter 2.
Figure 25
Figure 26
Oil Drain
Plug
Top of Rail
CONTACT US AT www.DRpower.com
15
Guard
Flange Locknuts and Flat Washers
Figure 27
Yoke
Grease
Fitting
Figure 28
Yoke Grease
Fitting
Figure 29
Safety
Interlock
Lever
Rail Maintenance
Between each use of the LOG SPLITTER, we recommend applying a rust preventative (Fluid Film or equivalent) to any bare metal areas on the top of the rail ( Figure 26 ). This will assure the smoothest return action of the ram.
Greasing the Engagement Handle and Yoke
Flange Bolts and Flat
Washers
Tools and Supplies needed:
9/16" Wrench
Extended Hose Grease Gun with all Purpose Grease
Clean Rags
Engagement
Handle
Grease
Fitting
1.
Remove the two Flange Bolts and Washers at the front of the right side
Guard and the two locknuts and Washers at the rear of the guard using a
9/16" Wrench. Remove the Guard from the Splitter ( Figure 27 ).
2.
Clean the Engagement Handle and Yoke Grease Fittings with a clean Rag
( Figure 28 and 29 ).
3.
Grease the Engagement Handle Grease Fitting with a few pumps of All
Purpose Grease.
Note: If there is a Height Adjustment Bolt in front of the Yoke Grease Fitting preventing access ( Figure 30 ), you will need to remove it using a 9/16" Wrench.
Not all machines have the Height Adjustment Bolt.
4.
Grease the Yoke with a few pumps of All Purpose Grease.
5.
Reinstall and adjust the Height Adjust Bolt only enough so the Handle is not touching the
Belt ( Figure 31 ).
Hold the Bolt still while tightening
Lever the Jam
Height Adjust
Bolt
Nut using two 9/16"
Wrenches
( Figure 30 ).
6.
Reinstall the
Guard.
Figure 30
Engagement Handle
Grease Fitting
Safety Lever
Clearance
Belt
Figure 31
16 DR ®
RAPIDFIRE™ LOG SPLITTER
Changing and Adjusting the Belts
Tools and Supplies needed:
Two 9/16" Wrenches
DR Belts
Guard
1.
Remove the two Flange Bolts and Washers at the front of the right side
Guard and the two Locknuts and Washers at the rear of the guard using a
9/16" Wrench. Remove the Guard from the Splitter ( Figure 32 ).
2.
Loosen the front two Engine Mount Pivot Bolts and Locknuts with two 9/16"
Wrenches ( Figure 33 ).
3.
Loosen the rear two Angle Setting Bolts with Flat Washers using two 9/16"
Wrench.
4.
Pivot the Mount up slightly and remove the Belts.
Note: The weight of the Engine should be enough to tension the Belts properly but depending on hardware looseness and cleanliness of Engine Mount pivot area, you may need to push down slightly to aid in proper tension. The Belts perform best with a slight amount of slack to allow for some slippage when the Wedge encounters a tough log. Too much tension may stall the engine or slip the belt on the engine pulley.
Flange Locknuts and Flat Washers
Figure 32
5.
Install the new Belts and adjust tension as needed.
6.
Tighten the two Engine Mount Bolts that are at the center of the machine
(shown) first and then tighten the outer two Bolts.
7.
Reinstall the Guard.
Adjusting the Rack Alignment
Rear Bolts and
Flat Washers
Front Bolts and Locknuts
Figure 33
Tools and Supplies needed:
9/16" Wrench
7/16" Wrench
1.
Remove the two Flange Bolts and Washers at the front of the right side
Guard and the two flanged locknuts and Washers at the rear of the guard using a 9/16" Wrench. Remove the Guard from the Splitter ( Figure 34 ).
2.
Pull the Ram out enough to disconnect the Return Springs from the Ram
Bearing Hardware ( Figure 35 ) and pull the Ram out to the Wedge.
3.
Center the Rack to the Frame.
Guard
Flange Locknuts and Flat Washers
Figure 34
Safety
Interlock
Lever
Flange Bolts and Flat
Washers
Loosen Belts
Tighten Belts
Safety
Interlock
Lever
Flange Bolts and Flat
Washers
Spring
Ram
Bearing
Figure 35
CONTACT US AT www.DRpower.com
17
Frame
Jam Nut
Figure 36
Guard
Flange Locknuts and Flat Washers
Figure 37
Rack
Carriage
Bolts
Jam Nut
4.
Loosen the Jam Nuts with a 9/16" Wrench and turn the Carriage Bolts with a
10mm Wrench until they touch the Rack ( Figure 36 ).
5.
Turn each Carriage Bolt back away from Rack two turns.
6.
Tighten the Locknuts against the Frame to lock the Carriage Bolts into place.
7.
Replace the Guard.
Adjusting the Steel Bushing Over Center
Tools needed:
Two 9/16" Wrenches
9/16" Socket and Ratchet
Safety
Interlock
Lever
Flange Bolts and Flat
Washers
1.
Remove the two Flange Bolts and Washers at the front of the right side
Guard and the two flanged locknuts and Washers at the rear of the guard using a 9/16" Wrench. Remove the Guard from the Splitter ( Figure 37 ).
2.
Loosen the Stop Bolt Jam Nuts ( Figure 38 ).
3.
Lift the Safety Interlock Lever and push the Engagement Handle forward to position the Steel Bushing Yoke as close to vertical as you can and hold it there ( Figure 39 ).
4.
Rotate the Stop Bolts until they touch the Steel Bushing Yoke. Turn the Bolt back out of the Frame counterclockwise 1-1/4 revolutions. Tighten the Jam
Nuts with a 9/16" Wrench to lock the Stop Bolts at this position.
Yoke
Do not adjust more than 1-1/4 revolutions when adjusting off center.
Adjustment too far off center will not allow the Rack Teeth to engage fully and will cause damage to the Splitter.
Jam
Nuts
5.
Replace the Guard.
Over Center
Position
Vertical Position
Forward Stop
Adjustment
Stop
Bolts
Figure 38
Steel
Bushing
Pinion
Rack
Back of
Yoke
Figure 39
18 DR ®
RAPIDFIRE™ LOG SPLITTER
Replacing the Wheels
Tools and Supplies needed:
Channel lock Pliers
Clean Rags
Adjustable Wrench
Needle Nose Pliers
Jack and Jack Stands
Hammer and Wood Block
Dust Cap
The Splitter must be supported carefully so it does not tip over when jacking or it could cause Splitter damage or personal injury.
Figure 40
1.
Jack the Splitter off the ground and secure with Jack Stands.
2.
Remove the Dust Cap from the Wheel Assembly with Channel Lock Pliers
( Figure 40 ).
3.
Straighten the ends of the Cotter Pin with Needle Nose Pliers so the Cotter
Pin can be pulled from the hole in the Axle ( Figure 41 ).
4.
Remove the Castle Nut with the Channel Lock Pliers.
5.
Pull the Wheel assembly and Taper Bearing from The Axle ( Figure 42 ).
6.
Slide a Wheel Assembly onto the Axle Shaft with the Valve Stem facing out.
The open side of the Wheel Hub with the loose Taper Bearing will be facing towards you.
7.
Screw the Castle Nut onto the Axle and tighten it with an Adjustable Wrench to seat the Bearings ( Figure 41 ).
8.
Back the Castle Nut off and then snug it up to the Bearing lightly.
9.
Insert a Cotter Pin through the slots of the Castle Nut and into the hole in the Axle.
10.
Bend the ends of the Cotter Pin with Needle Nose Pliers to secure it.
11.
Place the Dust Cap onto the Wheel Assembly and secure it by placing a piece of wood over it and pounding lightly with a Hammer until it is seated against the lip ( Figure 43 ).
12.
Jack the back of the Splitter up and remove the Jack Stands.
13.
Lower the Splitter to the ground.
Replacing the Battery
Figure 41
Figure 42
Tools Needed:
Two 7/16" Wrenches
Valve
Stem
When working with batteries take care not to short the positive terminal with the battery strap
Figure 43
Cotter Pin
Castle
Nut
Taper
Bearing
Dust Cap
Wheel
Assembly
CONTACT US AT www.DRpower.com
19
Battery
Terminals
1.
Disconnect the Battery Terminals ( Figure 44 ).
2.
Remove the Bolts and Locknuts that secure the Battery Strap using two
7/16" Wrenches.
3.
Remove the Strap and the old Battery.
Battery
Strap 4.
Install the new Battery.
5.
Install the Battery Strap and secure with the Bolts and Locknuts using two
7/16" Wrenches.
6.
Attach the Battery Terminals. Black Wire to the negative black Terminal and
Red Wire to the positive red Terminal.
Figure 44
Bolt and
Locknut Battery
Battery Care (electric start models)
Proper care can extend the life of a Battery. Follow these recommendations to ensure your Battery’s best performance and long life:
Do not allow the Battery charge to get too low. If the machine is not used, charge the Battery every 4 – 6 weeks. Operate the engine for at least 45 minutes to maintain proper Battery charge.
Store an unused Battery in a dry environment with temperatures between +40°F (+5°C) and +95°F (+35°C). Make sure the storage temperatures will never be outside of these limits. The lower the storage temperature is within the specified temperature, the better as the battery will discharge more slowly at low temperatures.
Do not charge an already charged Battery. In theory, you cannot overcharge our Battery with a trickle charger; however, when a
Battery is fully charged and the charger is still on, it generates heat that could be harmful to the Battery. A fully charged Battery will read 12V-13.2V with a voltmeter.
Do not continue to crank your Engine when the Battery charge is low.
Charging the Battery
Operate the Engine for at least 45 minutes to maintain proper Battery charge. If the Battery loses its charge, you will need to use a trickle charger (like the DR Battery Charger) to recharge it. The Charger should have an output of 12 volts DC at no more than 2 amps.
At 1 amp the Battery may need to be charged for as long as 48 hours.
At 2 amps, the Battery may need to be charged for as long as 24 hours.
NOTE: Using the Recoil Starter and then running the Engine will not recharge a dead or significantly discharged Battery.
To connect a Battery Charger to your DR RAPIDFIRE LOG SPLITTER, follow the steps listed below.
1.
Attach the Black (-) alligator clipped wire from the Charger Adapter to the Negative (-) terminal of the Battery, then attach the
Red (+) alligator clipped wire to the Positive (+) Battery terminal.
When you are finished charging the battery, disconnect the charger from the outlet first, then disconnect the battery charger wires from the battery. If you leave the battery charger wires connected to the battery, the battery will discharge itself back into the charger.
2.
Plug the Charger into a standard wall outlet.
Typically, the Battery takes between 6 and 8 hours to fully charge. Do not leave the charger on the battery longer than
24 hours for a 2 amp charger, or 48 hours for a 1 amp charger as you could potentially damage the battery..
You can charge the Battery many times. The Battery lasts longer if you charge it before it is fully drained. Keep it fully charged and at room temperature when not using your DR RAPIDFIRE LOG SPLITTER.
If the Battery does not hold its charge for very long under normal conditions or it simply won’t hold a charge, then replace it. You can purchase replacement Batteries directly from us. To install your new Battery, follow the directions on the previous page.
20 DR ®
RAPIDFIRE™ LOG SPLITTER
Disposing of the Battery Responsibly
The Battery is a sealed lead-acid Battery. Recycle or dispose of it in an environmentally sound way.
Do not dispose of a lead-acid Battery in a fire; the Battery may explode or leak.
Do not dispose of a lead-acid Battery in your regular, household trash. Law in most areas prohibits incinerating, disposing in a landfill, or mixing a sealed lead-acid Battery with household trash.
Recycling a Used Battery
Please dispose of your used Batteries responsibly by recycling them. Call your local Solid Waste Management District or your local waste handler to locate the collection site nearest you. Some collection sites recycle Batteries year-round; others collect them periodically.
You can also visit the Web site of Earth 911 for more information [www.earth911.org]. Enter the search term 'battery' and your zip code in the search function at the top of the page. The site lists recycling centers located near you.
For a fee, you can recycle your Batteries with the International Metals Reclamation Company. Visit them at www.inmetco.com and click Services; or contact them at:
INMETCO, One INMETCO Drive, Ellwood City, PA 16117, (724) 758-2800; fax (724) 758-2845
To learn more about hazardous waste recycling, visit the Web site for Battery Council International [www.batterycouncil.org] or for the Environmental Protection Agency [www.epa.gov].
CONTACT US AT www.DRpower.com
21
Chapter 5: Troubleshooting
Most problems are easy to fix. Consult the Troubleshooting Table below for common problems and their solutions. If you continue to experience problems, contact us at www.DRpower.com or call toll-free 1-800-DR-OWNER (376-9637) for support.
Before performing any maintenance procedure or inspection, stop the engine, wait five (5) minutes to allow all parts to cool.
Disconnect the spark plug wire, keeping it away from the spark plug.
Troubleshooting Table
S YMPTOM
The engine won’t start.
(Please refer to the engine owner’s manual for engine-specific procedures.)
The engine lacks power or is not running smoothly.
(Please refer to the engine owner’s manual for engine-specific procedures.)
Engine smokes.
(Please refer to the engine owner’s manual for engine-specific procedures.)
Rack catching on tail tube (at end of stroke).
Rack returning very slow or not returning properly.
P OSSIBLE C AUSE
Is the ignition switch in the “On” position?
Is the fuel shut-off valve on?
Are you using fresh, clean gas? If the gas is old, change it. Use a fuel stabilizer if you keep gas longer than 30 days.
Is the spark plug clean? If the spark plug is dirty or cracked, change it. If it’s oily, leave it out, hold a rag over the plug hole and pull the recoil cord several times to blow out any oil in the cylinder, then wipe off the plug and reinsert it.
If your engine still won’t start, contact us at www.DRpower.com
for assistance.
Check that the Throttle Lever is in the “Run” position and the Choke is off.
Is the air filter clean? If it’s dirty, change it following the procedure in the engine manufacturer’s owner’s manual.
Is the spark plug clean? If it’s fouled or cracked, change it. If it’s oily, leave it out, hold a rag over the plug hole and pull your recoil cord several times to blow out any oil in the cylinder, then wipe off the plug and reinsert it.
Are you using fresh, clean unleaded gas? If it’s old, change it. Use a fuel stabilizer if you keep gas longer than 30 days.
Does your engine have the right amount of clean oil? If it’s dirty, change it following the procedure in the engine manufacturer’s owner’s manual.
Check the oil level and adjust as needed.
If your engine still lacks power, contact us at www.DRpower.com
for assistance.
The choke may still be on; Move the choke lever to the open position.
Check the oil level and adjust as needed.
Check the air filter and clean or replace if needed.
You may be using the wrong oil—too light for the temperature. Refer to your Engine Owner’s
Manual for detailed information.
Clean the cooling fins if they’re dirty.
If the engine still smokes, contact us at www.DRpower.com
for assistance.
Check for wood chips or debris between ram bushing plate and beam. Clean beam of built up/caked on debris.
Check rack lift bearing for alignment or damage.
Return spring is unhooked or damaged. Reconnect or replace as needed.
Machine wedge end too low. Must be almost level or wedge end slightly higher. Perform rail maintenance and lubricate the beam- prolonged exposure may rust the beam without lubrication.
22 DR ®
RAPIDFIRE™ LOG SPLITTER
Troubleshooting Table (Continued)
Before performing any maintenance procedure or inspection, stop the engine, wait five (5) minutes to allow all parts to cool.
Disconnect the spark plug wire, keeping it away from the spark plug.
S YMPTOM
Operator Lever snapping out of gear or not staying in gear.
Rack slamming back too fast.
Machine does not seem to have full splitting power.
Operator Lever not engaging rack with pinion gear.
Rack not disengaging from pinion when handle is released
P OSSIBLE C AUSE
Lever not all the way forward when rack comes under full load. Push lever quicker and more forcefully into the full forward position. A hard stop should be felt at the end of the stroke when engaging the handle.
Stop bolt may be bent or not adjusted properly; contact us at www.DRpower.com
for assistance.
Ram has been overloaded at lower part of face. Check rack gear for straightness.
Wedge end of machine too high. Must be almost level with ram end or just slightly higher.
Springs not operating properly. Fix or replace as needed.
The belt(s) may be too loose and slipping. Adjust or replace belt(s) as needed.
Clean wood chips or other debris from under rack.
Clean accumulated dirt from frame where carriage assembly rests against rubber bumpers.
Belts must be loosened to allow for slipping while disengaging
CONTACT US AT www.DRpower.com
23
Chapter 6: Parts Lists and Schematic Diagrams
4
5
6
7
Parts List - TOW BAR AND GUARD ASSEMBLY
NOTE: Part numbers listed are available through DR Power Equipment.
Ref# Part# Description Ref# Part#
2 32104 Bolt, Carriage, 3/8-16 X 1", GR5, ZP
Description
15
16
16003
18967
Pin, Hair, 1/2" To 9/16", .12" Wire
Washer, Flat, Neoprene, .490"ID X
1.06"OD X .09"TH
17 35244 Label, Branding
33351
33333
33374
25044
Bolt, Hex, Flange, 3/8-16 X 1.25"
Nut, Nylon Lock, Flanged, 3/8-16
Guard, Plastic, LH, W/ Warning Labels
Label, Warning, Pinch Point, 3.5"x1"
9 33373 Guard, Plastic, RH, W/ Warning Labels
10 32128 Label,
11 36740 Towbar
12 32105 Mount,
13 32110 Stand,
14 18737 Pin, Clevis, 1/2" OD X 4.5" LG
18 33335
19 33351
20 33333
21 33353
22 33348
23 11239
24 35089
25 36545
Nut, Nylon Lock, Flanged, 1/2-13
Bolt, Hex, Flange, 3/8-16 X 1.25"
Nut, Nylon Lock, Flanged, 3/8-16
Bolt, Hex, Flange, 1/2-13 X 4"
Bolt, Hex, Flange, 3/8-16 X 2.5"
Washer, Flat, 3/8", USS
Bolt, HCS, 3/8-16 X 5.50", Full Thread,
GR 5, ZP
Label, RapidFire Splitting Tips
24 DR ®
RAPIDFIRE™ LOG SPLITTER
Schematic – TOW BAR AND GUARD ASSEMBLY
CONTACT US AT www.DRpower.com
25
3
1
2
4
5
6
Parts List – DRIVE ASSEMBLY
NOTE: Part numbers listed are available through DR Power Equipment.
Ref# Part# Description Ref# Part#
29461
32125
37075
37076
34406
29487
33331
29494
29493
Flywheel, 75 Lb (K34)
Flywheel, 55 Lb (K28)
Engine, B&S, 9.50 XR, E/S, W/Labels
Engine, B&S, 9.50 CR, M/S, W/Labels
Engine, DR 5.8, M/S Rato W/labels
Boot, Terminal, Red
Nut, Nylon Lock, Flanged, 1/4-20
Key, Square, 3/8" X 3/8" X 1.5" L
Screw, Set, Cup Point, 3/8 X 16 X .5 L
8
9
27575
16514
10 11243
Key, Square, 3/16" X 3/16" - 1/2"
Washer, .385" ID, 1.39" OD, .15" T
Washer, Lock, Split, 5/16"
11 17882 Bolt, HCS, 5/16-24 x 1", GR2 ZP
12 29455 Housing,
13 29456 Insert Bearing W/ Snap Ring
14 31356 Mount,
15 32111 Bearing,
12mm W
16 32107 Ram
17 29459 Gear,
18 29468 Spring, Carriage
19 32099 Bracket, Rack, Lifter
Description
20 32114 Pulley, 2 Groove, 4l, 3/4" Keyway
21 33356 Belt,
22 29498 Cylinder,
23 32126 Bracket, Stop
24 32122 Washer, 5/16" ID, 2.0" OD, 0.13" T
Bolt, HHCS, 5/16-18 X 1.25", GR.5, ZP 25 12336
26 11152
27 33358
28 31238
29 23499
Bolt, HHCS, .375-16 X 1.00" Lg.
Bolt, Hex, Flange, M12-1.75 x 50, CL 8.8,
ZP
Bolt, HCS, 1/2-20 X 2.5", GR8, ZP
30
31
33351
33352
Washer, SAE Flat, 1/2", ZP
Bolt, Hex, Flange, 3/8-16 X 1.25"
Bolt, Hex, Flange, 5/16-18 X 1.5"
32 33332
33 33333
Nut, Nylon Lock, Flanged, 5/16-18
Nut, Nylon Lock, Flanged, 3/8-16
34 18755
35 13443
Nut, Nylon Lock, 5/16-18, LP
Bolt, HCS, 5/16-18 X 1-1/2", GR5, ZP
36 11242 Washer, 0.5"
37 30253
38 33354
39 33346
Nut, Nylon Lock, M12-1.75
Bolt, HCS, M12-1.75 x 30, CL 8.8, ZP
Bushing, Bronze, 0.5" ID, 0.625" OD,
0.375" L
26 DR ®
RAPIDFIRE™ LOG SPLITTER
Schematic – DRIVE ASSEMBLY
CONTACT US AT www.DRpower.com
27
Parts List – FRAME AND AXLE ASSEMBLY
NOTE: Part numbers listed are available through DR Power Equipment.
Ref# Part# Description Ref# Part#
3 11468 Bolt, HHCS, 1/4-20 X 2.0", GR2, ZP
6 31362 Axle
7 25297 Wheel & Tire Assembly, w/Dust Cap
10 31374 Brace,
11 32106 Catch, Engagement
12 32109 Hand
13 10189 Grease Fitting 1/4-28 Straight
14 18081 Washer, 3/8"
15 25311 Pin, Cotter, 5/32" x 2"
16 11241
17 11022
Washer, Flat, 5/16", USS, ZP
Grip, Shift Handle
18 23103
19 32098
20 33355
Bolt, Carr, 3/8-16 x 1 3/4", GR5, ZP
Bushing, Bronze, SAE 954
Grip, Foam, 1" Tube, 5.1" Long
21 18085 Bolt, HCS, 1/4-20 x 2.75"
22 25310 Nut, Slotted
23 29471 Spring, Extension, Carriage Return
Description
24 11242 Washer, 0.5"
25 10948 Cap, Round, 1"
26 35216
27 33331
28 33349
29 33351
Bracket, Cover, Mounting
Nut, Nylon Lock, Flanged, 1/4-20
Bolt, Hex, Flange, 1/2-13 X 5"
Bolt, Hex, Flange, 3/8-16 X 1.25"
30 33350 Bolt, Hex, Flange, 3/8-16 X 2"
31 35237 Bushing,
32 35359
33 36553
Nut, Hex, Jam, 1/2-13, GR5, ZP
Bolt, HCS, 1/2-13 x 2", Partial Thd, GR8
34 28697
35 33333
36 33335
Pad, Battery 2.5" X 6.125"
Nut, Nylon Lock, Flanged, 3/8-16
Nut, Nylon Lock, Flanged, 1/2-13
37 35238 Bracket, Control Interface
38 35225 Yoke,
39 35223 Handle
40 35224 Link,
41 35240 Spring,
42 35358 Bolt, Hex Tap Bolt, Fully Threaded, 3/8-
16 X 3-1/2", GR8, ZP
43 22909
44 34512
Bolt, HCS, 1/2-13 X 1-1/2", GR5, ZP
Bolt, Hex, Flange, 3/8-16 X .75", GR5, ZP
45 24230 Strap,
28 DR ®
RAPIDFIRE™ LOG SPLITTER
Schematic – FRAME AND AXLE ASSEMBLY
CONTACT US AT www.DRpower.com
29
5
6
2
3
Parts List – TRAY KIT ASSEMBLY
NOTE: Part numbers listed are available through DR Power Equipment.
Ref# Part# Description
32104
15043
Bolt, Carriage, 3/8-16 X 1", GR5, ZP
Bolt, HHCS, 3/8-16 X 1-1/4", GR5
11241
33333
Washer, Flat, 5/16" USS, ZP
Nut, Nylon Lock, Flanged, 3/8-16
30 DR ®
RAPIDFIRE™ LOG SPLITTER
DR
®
RAPIDFIRE™ LOG SPLITTER
2-Year Limited Warranty
Terms and Conditions
The DR
RAPIDFIRE™ Log Splitter is warranted for two (2) years against defects in materials or workmanship when put to ordinary and normal consumer use; 90 days for commercial use. The engine manufacturer warrants the engine separately.
For the purposes of all the above warranties, “ordinary and normal use” does not include misuse, accidents or damage due to inadequate maintenance.
DR
Power Equipment certifies that the DR product of this type is used. DR
RAPIDFIRE™ Log Splitter is fit for ordinary purposes for which a
Power Equipment however, limits the implied warranties of merchantability and fitness in duration to a period of two (2) years in consumer use; 90 days for commercial use.
The 2-Year Limited Warranty on the DR
RAPIDFIRE™ Log Splitter starts on the date the machine ships from our factory. The 2-Year Limited Warranty is applicable only to the original owner.
The warranty holder is responsible for the performance of the required maintenance as defined by the manufacturer's owner's manuals. The warranty holder is responsible for replacement of normally wearing parts such as the Drive
Belts, Air Filter, Highway Wheels, Battery, and Spark Plug. Accessories to the machine are not covered by this warranty.
During the warranty period, the warranty holder is responsible for the machine transportation charges, if required.
During the warranty period, warranty parts will be shipped by standard method at no charge to the warranty holder.
Expedited shipping of warranty parts is the responsibility of the warranty holder.
SOME STATES DO NOT ALLOW LIMITATIONS ON THE LENGTH OF IMPLIED WARRANTIES, SO THE ABOVE
LIMITATIONS MAY NOT APPLY TO YOU.
DR
Power Equipment shall not be liable under any circumstances for any incidental or consequential damages or expenses of any kind, including, but not limited to, cost of equipment rentals, loss of profit, or cost of hiring services to perform tasks normally performed by the DR
RAPIDFIRE™ Log Splitter.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU ALSO HAVE OTHER RIGHTS, WHICH VARY
FROM STATE TO STATE.
Daily Checklist for the DR LOG SPLITTER
To help maintain your DR LOG SPLITTER for optimum performance, we recommend you follow this checklist each time you use your Log Splitter.
Before performing any maintenance procedure or inspection, stop the engine, wait five (5) minutes to allow all parts to cool.
Disconnect the spark plug wire, keeping it away from the spark plug.
[ ] Check the Engine Oil and Gas Tank level.
[ ] Check that Engine is clean of debris.
[ ] Check the general condition of the Log Splitter, e.g.; Nuts, Bolts, Welds, etc.
[ ] Check Tire Pressure and wear.
[ ] Check the Frame for wear and damage.
[ ] Check the Wedge for nicks and wear. Sharpen if needed.
[ ] Apply a rust preventative (Fluid Film or equivalent) to any bare metal areas on the top of the Rail. This will assure the longest possible service life of the Wear Pads.
End of Season and Storage
Before performing any maintenance procedure or inspection, stop the engine, wait five (5) minutes to allow all parts to cool.
Disconnect the spark plug wire, keeping it away from the spark plug.
Change the Engine Oil.
Clean or replace the Air Filter.
Check the Wedge for nicks and wear. Sharpen if needed.
Apply a rust preventative to the Rack and Pinion (fluid film or equivalent).
Apply a rust preventative (Fluid Film or equivalent) to any bare metal areas on the top of the Rail.
If your DR RAPIDFIRE LOG SPLITTER will be idle for more than 30 days, we recommend using a gas stabilizer. This will prevent sediment from gumming up the Carburetor. If there is dirt or moisture in the gas or Tank, remove it by draining the Tank.
Completely fill the Tank with fresh, unleaded gas and add the appropriate amount of stabilizer or gasoline additive. Run the
Engine for a short time to allow the additive to circulate.
Clean the exterior of the unit to remove all dirt, grease, and any other foreign material. Clean dirt and debris from the Cylinder
Head Cooling Fins and Muffler area of the Engine. To prevent rust, touch up painted surfaces that have been scratched or chipped.
Be sure all Nuts, Bolts, and Screws are securely fastened.
Remove the Spark Plug(s) and pour about 1 ounce of Motor Oil into the Cylinder hole. Replace the Plug(s) and crank the Engine over a couple of times using the Pull Cord, or the Electric Starter (for Electric Start Machines). This will coat the Piston and seat the Valves to prevent moisture buildup.
If possible, store the Log Splitter in a dry, protected place. If it is necessary to store the Log Splitter outside, cover it with a protective material (especially the Engine). For Electric Start Model, store the machine in a dry environment with temperatures between +40°°F (5°C) and +95F (+35°C). Make sure the storage temperatures will never be outside of these limits. The lower the storage temperature is within the specified temperature, the better as the Battery will discharge more slowly at low temperatures.
If it is necessary to store the Log Splitter outside make sure to disconnect the Battery and store it in an environment as listed above. Make sure the disconnected Battery terminals are not resting on any surface that may be prone to collecting water, snow or any other liquid as this may cause damage to the Terminals and to the Battery when reconnected.
7 5 M E I G S R O A D , P . O . B O X 2 5 , V E R G E N N E S , V E R M O N T 0 5 4 9 1
©2016 Country Home Products, Inc. All rights reserved 334341E
Download
Public link updated
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Document public link
Advertisement
