Sony XAV-AX5500 Bluetooth Media Receiver Instruction manual

Add to My manuals
16 Pages

advertisement

Sony XAV-AX5500 Bluetooth Media Receiver Instruction manual | Manualzz

AV RECEIVER

5-010-46222 (1)

Operating Instructions

GB

To cancel the demonstration (Demo) display, see page 8.

To switch the FM/AM tuning step, see page 7.

For the connection/installation, see page 12.

XAV-AX5500

Warning

For safety, be sure to install this unit in the dashboard of the car as the rear side of the unit becomes hot during use.

For details, see “Connection/Installation”

(page 12).

The nameplate indicating operating voltage, etc., is located on the bottom of the chassis.

The validity of the CE marking is restricted to only those countries where it is legally enforced, mainly in the countries EEA (European Economic Area) and

Switzerland.

WARNING

To prevent fire or shock hazard, do not expose the unit to rain or moisture.

To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

Disposal of waste batteries and electrical and electronic equipment (applicable in the

European Union and other countries with separate collection systems)

WARNING: Do not ingest battery,

Chemical Burn Hazard.

The remote commander contains a coin/ button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just

2 hours and can lead to death.

Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children.

If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

Note on the lithium battery

Do not expose the battery to excessive heat such as direct sunlight, fire or the like.

Warning if your car’s ignition has no ACC position

Do not install this unit in a car that has no ACC position. The display of the unit does not turn off even after turning the ignition off, and this causes battery drain.

Disclaimer regarding services offered by third parties

Services offered by third parties may be changed, suspended, or terminated without prior notice.

Sony does not bear any responsibility in these sorts of situations.

2

GB

Important notice

Caution

IN NO EVENT SHALL SONY BE LIABLE FOR ANY

INCIDENTAL, INDIRECT OR CONSEQUENTIAL

DAMAGES OR OTHER DAMAGES INCLUDING,

WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF

REVENUE, LOSS OF DATA, LOSS OF USE OF THE

PRODUCT OR ANY ASSOCIATED EQUIPMENT,

DOWNTIME, AND PURCHASER’S TIME RELATED TO

OR ARISING OUT OF THE USE OF THIS PRODUCT, ITS

HARDWARE AND/OR ITS SOFTWARE.

Dear customer, this product includes a radio transmitter.

Please check your vehicle operation manual or contact the manufacturer of your vehicle or your vehicle dealer, before you install this product into your vehicle.

Emergency calls

This BLUETOOTH car handsfree and the electronic device connected to the handsfree operate using radio signals, cellular, and landline networks as well as user-programmed function, which cannot guarantee connection under all conditions.

Therefore do not rely solely upon any electronic device for essential communications (such as medical emergencies).

On BLUETOOTH communication

• Microwaves emitting from a BLUETOOTH device may affect the operation of electronic medical devices. Turn off this unit and other BLUETOOTH devices in the following locations, as it may cause an accident.

– where inflammable gas is present, in a hospital, train, airplane, or petrol station

– near automatic doors or a fire alarm

• This unit supports security capabilities that comply with the BLUETOOTH standard to provide a secure connection when the BLUETOOTH wireless technology is used, but security may not be enough depending on the setting. Be careful when communicating using BLUETOOTH wireless technology.

• We do not take any responsibility for the leakage of information during BLUETOOTH communication.

If you have any questions or problems concerning your unit that are not covered in this manual, consult your nearest Sony dealer.

3

GB

Guide to Parts and Controls

Main Unit and Remote Commander

Main unit

The VOL (volume) + button has a tactile dot.

 Display/touch screen

 HOME

Displays the HOME screen (page 6).

ATT (attenuate)

Press and hold for 1 second to attenuate the sound.

To cancel, press and hold again, or press VOL +.

 VOL (volume) +/–

Receptor for the remote commander

  /  (previous/next)

Functions differently depending on the selected source:

– Radio: select a preset station.

– USB/BT Audio: move to the previous/next file.

Press and hold to:

– Radio: tune into a station automatically

(SEEK+/SEEK–).

– USB/BT Audio: fast-reverse/fast-forward.

 OPTION

Displays the OPTION screen (page 6).

VOICE

Press and hold to activate the voice command function for Apple CarPlay and Android Auto™.

4

GB

RM-X170 remote commander

The remote commander can be used to operate the audio controls. For menu operations, use the touch screen.

  /  (previous/next)

 /  (fast-reverse/fast-forward)

Functions differently depending on the selected source:

– Radio: select a preset station.

– USB/BT Audio: move to the previous/next file.

Press and hold to:

– Radio: tune into a station automatically

(SEEK+/SEEK–).

– USB/BT Audio: fast-reverse/fast-forward.

  /  /  / 

Functions differ depending on the selected source.

– Radio: select a preset station or tune into a station automatically.

– USB: select a folder or move to the previous/ next file.

ENTER

Enters the selected item.

 SRC (source)

Changes the source. Each time you press this button, a selectable source is displayed in a popup on the current display.

 MODE

Selects the radio band.

 VOL (volume) +/–

Remove the insulation film before use.

Note

The white buttons in the illustration above are not supported.

OFF

Turns the source off.

 MONITOR OFF

Turns off the monitor.

To turn back on, press again.

 EQ (equalizer)

Selects an equalizer curve.

 Number buttons (0 to 9)

 CLEAR

ATT (attenuate)

Attenuates the sound. Press again to cancel the attenuation.

 

(play/pause)

5

GB

Screen displays

Playback screen:

HOME screen:

OPTION screen:

 Status indication

Lights up when the sound is attenuated.

Lights up when the Bluetooth® signal is on. Flashes when the connection is in progress.

Lights up when the audio device is playable by enabling the A2DP

(Advanced Audio Distribution Profile).

Lights up when handsfree calling is available by enabling the HFP (Handsfree

Profile).

Indicates the signal strength status of the connected mobile phone.

Indicates the remaining battery status of the connected mobile phone.

 (source option)

Opens the source option menu. The available items differ depending on the source.

 Application specific area

Displays playback controls/indications or show the unit’s status. Displayed items differ depending on the source.

 Clock

Displays the time which are set on the date/time setting.

 (return to the playback screen)

Switches from the HOME screen to the playback screen.

 Sources and Settings select keys

Changes the source or make various settings.

Flick to select the setting icon and other icons.

Touch the source icon you want to select.

Android

Auto

BT Audio

Apple

CarPlay

Phone

Radio

WebLink USB port 2

USB port 1

Rear

Camera

Settings

6

GB

 Sound select keys

Changes the sound.

 

(standby)

Turns the unit in standby mode (USB charging is still available). To resume, press any buttons.

(monitor off)

Turns off the monitor. When the monitor is turned off, touch any part of the display to turn it back on.

 (EXTRA BASS)

Changes the EXTRA BASS setting.

(EQ10/subwoofer)

Changes the EQ10/subwoofer setting.

Basic Operations

Switching the FM/AM Tuning

Step

Set the FM/AM tuning step of your country or region.

1

Press HOME, touch [Settings]

[General]

[Tuning Steps], then set the FM/AM tuning step.

2

To exit the setup menu, touch (back) three times.

Pairing with a BLUETOOTH Device

When connecting a BLUETOOTH device for the first time, mutual registration (called “pairing”) is required. Pairing enables this unit and other devices to recognize each other.

1

Press HOME, then touch [Settings]

[Bluetooth]

[Bluetooth Connection]

[ON]

[Pairing].

flashes while the unit is in pairing standby mode.

2

Perform pairing on the BLUETOOTH device so it detects this unit.

3

Select your model name shown on the display of the BLUETOOTH device*.

When pairing is made, stays lit.

* If passkey input is required on the BLUETOOTH device, input [0000].

Connecting Rear View Camera

By connecting the optional rear view camera to the

CAMERA IN terminal, you can display the picture from the rear view camera. For details, see

“Connection/Installation” (page 12).

To display the picture from the rear view camera

Press HOME, then touch [Rear Camera].

7

GB

Canceling the Demonstration

Mode

1 Press HOME, then touch [Settings].

2

Touch [General], then touch [Demo] to set to

[OFF].

3

To exit the setup menu, touch (back) twice.

Updating the Firmware

To update the firmware, visit the support site on the back cover, then follow the online instructions.

Note

During the update, do not remove the USB device.

Additional Information

Precautions

• Power antenna (aerial) extends automatically.

• When you transfer ownership or dispose of your car with the unit installed, initialize all the settings to the factory settings by performing the factory reset.

• Do not splash liquid onto the unit.

Notes on safety

• Comply with your local traffic rules, laws, and regulations.

• While driving

– Do not watch or operate the unit, as it may lead to distraction and cause an accident. Park your car in a safe place to watch or operate the unit.

– Do not use the setup feature or any other function which could divert your attention from the road.

– When backing up your car, be sure to look back and watch the surroundings carefully for your safety even if the rear view camera is connected.

Do not depend on the rear view camera exclusively.

• While operating

– Do not insert your hands, fingers, or foreign objects into the unit as it may cause injury or damage to the unit.

– Keep small articles out of the reach of children.

– Be sure to fasten seatbelts to avoid injury in the event of sudden movement of the car.

Preventing an accident

Pictures appear only after you park the car and set the parking brake.

If the car starts moving during video playback, the following caution is displayed and you cannot watch the video.

[Video blocked for your safety.]

Do not operate the unit or watch the monitor while driving.

8

GB

Notes on LCD panel

• Do not get the LCD panel wet or expose it to liquids. This may cause a malfunction.

• Do not press down hard on the LCD panel as doing so can distort the picture or cause a malfunction (i.e., the picture may become unclear or the LCD panel may be damaged).

• Do not touch the panel with objects other than with your finger as it may damage or break the

LCD panel.

• Clean the LCD panel with a dry soft cloth. Do not use solvents such as benzine, thinner, commercially available cleaners, or antistatic spray.

• Do not use the unit outside the temperature range

0 ºC to 40 ºC (32 ºF to 104 ºF).

• If your car was parked in a cold or hot place, the picture may not be clear. However, the monitor is not damaged and the picture will become clear after the temperature in your car becomes normal.

• Some stationary blue, red, or green dots may appear on the monitor. These are called “bright spots” and can happen with any LCD. The LCD panel is precision-manufactured with more than

99.99% of its segments functional. However, it is possible that a small percentage (typically 0.01%) of the segments may not light up properly. This will not, however, interfere with your viewing.

Notes on the touch screen

• This unit uses a capacitive touch screen. Touch the screen directly with your fingertip.

• Multi-touch operation is not supported on this unit.

• Do not touch the screen with sharp objects such as a needle, pen, or fingernail. Operation with a stylus is not supported on this unit.

• Touching the screen with a gloved finger may cause the unit to operate incorrectly or not respond.

• Do not let any objects contact the touch screen. If the screen is touched by an object other than your fingertip, the unit may not respond correctly.

• Since glass material is used for the screen, do not subject the unit to strong shock. If cracking or chipping occurs on the screen, do not touch the damaged part as it may cause injury.

• Keep other electrical devices away from the touch screen. They may cause the touch screen to malfunction.

• If there are water droplets on the touch screen, or if you touch the screen with wet fingertips, the touch screen may not react correctly.

About iPhone

• Compatible iPhone models: iPhone XS Max, iPhone XS, iPhone XR, iPhone X, iPhone 8 Plus, iPhone 8, iPhone 7 Plus, iPhone 7, iPhone SE, iPhone 6s Plus, iPhone 6s, iPhone 6 Plus, iPhone 6, iPhone 5s

• Use of the Made for Apple badge means that an accessory has been designed to connect specifically to the Apple product(s) identified in the badge, and has been certified by the developer to meet Apple performance standards.

Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.

Please note that the use of this accessory with an

Apple product may affect wireless performance.

Notice on license

This product contains software that Sony uses under a licensing agreement with the owner of its copyright. We are obligated to announce the contents of the agreement to customers under requirement by the owner of copyright for the software.

For details on software licenses, select [Settings]

[General]  [Open Source Licenses].

If you have any questions or problems concerning your unit that are not covered in this Operating

Instructions, consult your nearest Sony dealer.

9

GB

Maintenance

Replacing the lithium battery (CR2025) of the remote commander

When the battery becomes weak, the range of the remote commander becomes shorter.

CAUTION

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

Lithium battery (CR2025)

+ side up

Note on the lithium battery

Keep the lithium battery out of the reach of children. Should the battery be swallowed, immediately consult a doctor.

Specifications

Monitor section

Display type: Wide LCD color monitor

Dimensions: 6.95 in/176 mm

System: TFT active matrix

Number of pixels:

1,152,000 pixels (800 × 3 (RGB) × 480)

Color system:

PAL/NTSC automatic select for CAMERA IN terminal

Radio section

FM

Tuning range:

87.5 MHz – 108.0 MHz (at 50 kHz step)

87.5 MHz – 108.0 MHz (at 100 kHz step)

87.5 MHz – 107.9 MHz (at 200 kHz step)

FM tuning step:

50 kHz/100 kHz/200 kHz switchable

Usable sensitivity: 7 dBf

Signal-to-noise ratio: 70 dB (mono)

Separation at 1 kHz: 45 dB

AM

Tuning range:

531 kHz – 1,602 kHz (at 9 kHz step)

530 kHz – 1,710 kHz (at 10 kHz step)

AM tuning step:

9 kHz/10 kHz switchable

Sensitivity: 32 μV

USB player section

Interface:

USB port 1 (Hi-speed)

USB port 2 (Full-speed)

Maximum current:

USB port 1: 1.5 A

USB port 2: 500 mA

Wireless communication

Communication System:

BLUETOOTH Standard version 3.0

Output:

BLUETOOTH Standard Power Class 2

(Max. Conducted +1 dBm)

Maximum communication range* 1 :

Line of sight approx. 10 m (33 ft)

Frequency band:

2.4 GHz band (2.4000 GHz – 2.4835 GHz)

Modulation method: FHSS

Compatible BLUETOOTH Profiles* 2 :

A2DP (Advanced Audio Distribution Profile) 1.3

AVRCP (Audio Video Remote Control Profile) 1.3

HFP (Handsfree Profile) 1.6

PBAP (Phone Book Access Profile) 1.1

Corresponding codec: SBC, AAC

10

GB

*1 The actual range will vary depending on factors such as obstacles between devices, magnetic fields around a microwave oven, static electricity, reception sensitivity, antenna (aerial)’s performance, operating system, software application, etc.

*2 BLUETOOTH standard profiles indicate the purpose of

BLUETOOTH communication between devices.

Power amplifier section

Outputs: Speaker outputs

Speaker impedance: 4 Ω – 8 Ω

Maximum power output: 55 W × 4 (at 4 Ω)

General

Power requirements: 12 V DC car battery

(negative ground (earth))

Rated current consumption: 10 A

Dimensions:

Approx. 178 mm × 100 mm × 139 mm

(7 1 /

8

in × 4 in × 5 1 /

2

in) (w/h/d)

Mounting dimensions:

Approx. 182 mm × 111 mm × 120 mm

(7 1 /

4

in × 4 3 /

8

in × 4 3 /

4

in) (w/h/d)

Mass: Approx. 1.0 kg (2 lb 4 oz)

Package contents:

Main unit (1)

Parts for installation and connections (1 set)

Remote Commander (1): RM-X170

Ask the dealer for detailed information.

Design and specifications are subject to change without notice.

Copyrights

The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Sony Corporation is under license. Other trademarks and trade names are those of their respective owners.

Windows Media is either a registered trademark or trademark of Microsoft Corporation in the United

States and/or other countries.

This product is protected by certain intellectual property rights of Microsoft Corporation. Use or distribution of such technology outside of this product is prohibited without a license from

Microsoft or an authorized Microsoft subsidiary.

Apple and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries.

Apple CarPlay is a trademark of Apple Inc.

Android Auto is a trademark of Google LLC.

WebLink is a registered trademark of Abalta

Technologies, Inc. in the U.S. and a trademark in the other countries.

All other trademarks are trademarks of their respective owners.

11

GB

Connection/Installation

Cautions

• Do not install this unit in a car that has no ACC position. The display of the unit does not turn off even after turning the ignition off, and this causes battery drain.

• Run all ground (earth) leads to a common ground (earth) point.

• Do not get the leads trapped under a screw or caught in moving parts (e.g., seat railing).

• Before making connections, turn the car ignition off to avoid short circuits.

• Connect the yellow and red power supply leads only after all other leads have been connected.

• Be sure to insulate any loose unconnected leads with electrical tape for safety.

• Choose the installation location carefully so that the unit will not interfere with normal driving operations.

• Avoid installing the unit in areas subject to dust, dirt, excessive vibration, or high temperature, such as in direct sunlight or near heater ducts.

• Use only the supplied mounting hardware for a safe and secure installation.

Note on the power supply lead (yellow)

When connecting this unit in combination with other stereo components, the amperage rating of the car circuit to which the unit is connected must be higher than the sum of each component’s fuse amperage rating.

Note on installing in cars with a start-stop system

The unit may restart when starting the engine from startstop. In this case, turn off the start-stop system of your car.

Note on installing in cars with electric parking brake system

For cars with electric parking brakes, some related functions

(such as video blocking function) may not work properly.

Mounting angle adjustment

Adjust the mounting angle to less than 30°.

Parts List for Installation

Power supply leads (1)

Mounting screws

(5 × max. 9 mm

( 7 / 32 × max. 3 / 8 in)) (4)

Microphone (1)

Double-sided tape (1)

USB extension cables (2)

Adhesive tapes (2)

Trim ring (1)

Flat-mount base (1)

Connection cable RC-SR1 (1)

This parts list does not include all the package contents.

12

GB

Connection

FUSE 10A

White

White/black striped

Gray

Gray/black striped

Green

Green/black striped

Purple

Purple/black striped

Black

Yellow

Red

Blue/white striped

Orange/white striped

Light green

Purple/white striped

Subwoofer* 1

* 3

* 3

* 3

* 3

Power amplifier* 1

Rear view camera* 1

* 8

* 6 * 7 from a wired remote control (not supplied) *4*9

USB device (for audio playback only)* 1

* 8

Smartphone, USB device

(for audio/video playback)* 1

Front speaker* 1 * 2

Rear speaker* 1 * 2

For details, see “Making connections” (page 14).

from a car antenna (aerial)* 5

13

GB

*1 Not supplied

*2 Speaker impedance: 4 Ω to 8 Ω × 4

*3 RCA pin cord (not supplied)

*4 Depending on the type of car, use an adaptor for a wired remote control (not supplied).

For details on using the wired remote control, see “Using the wired remote control” (page 15).

*5 Depending on the type of car, use an adaptor (not supplied) if the antenna (aerial) connector does not fit.

*6 Whether in use or not, route the microphone input cord so it does not interfere with driving operations. Secure the cord with a clamp, etc., if it is installed around your feet.

*7 For details on installing the microphone, see “Installing the microphone” (page 14).

*8 

 To the parking brake switch lead

The mounting position of the parking brake switch lead depends on your car.

Be sure to connect the parking brake lead (light green) of the power supply leads  to the parking brake switch lead.

Parking brake switch lead

*9 When using the steering wheel remote control, use the connection cable RC-SR1

as necessary.

Making connections

 To a common ground (earth) point

First connect the black ground (earth) lead then connect the yellow and red power supply leads.

 To the +12 V power terminal which is energized at all times

Be sure to first connect the black ground (earth) lead to a common ground (earth) point.

 To the +12 V power terminal which is energized when the ignition switch is set to the accessory position

Be sure to first connect the black ground (earth) lead to a common ground (earth) point.

 To the power antenna (aerial) control lead or the power supply lead of the antenna (aerial) booster

It is not necessary to connect this lead if there is no power antenna (aerial) or antenna (aerial) booster, or with a manually-operated telescopic antenna (aerial).

To AMP REMOTE IN of an optional power amplifier

This connection is only for amplifiers and a power antenna (aerial). Connecting any other system may damage the unit.

Note

It will take about 10 seconds to shut down the output of

REM OUT after the unit is turned off.

 To a car’s illumination signal

Be sure to first connect the black ground (earth) lead to a common ground (earth) point.

Hand brake type Foot brake type

To the +12 V power terminal of the car’s rear lamp lead (only when connecting the rear view camera)

Memory hold connection

When the yellow power supply lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off.

Speaker connection

• Before connecting the speakers, turn the unit off.

• Use speakers with an impedance of 4 Ω to 8 Ω and with adequate power handling capacities to avoid damage.

Installing the microphone

To capture your voice during handsfree calling, you need to install the microphone  .

Clip (not supplied)

14

GB

Cautions

• It is extremely dangerous if the cord becomes wound around the steering column or gearstick.

Be sure to keep it and other parts from interfering with your driving operations.

• If airbags or any other shock-absorbing equipment are in your car, contact the store where you purchased this unit or the car dealer before installation.

Notes

• When mounting on the dashboard, remove the visor clip carefully from the microphone

, then attach the flatmount base

to the microphone

.

• Before attaching the double-sided tape

, clean the surface of the dashboard with a dry cloth.

Using the wired remote control

When using the steering wheel remote control

Installation of the connection cable RC-SR1  is required before use.

1

To enable the steering wheel remote control, select

[General]  [Steering Control]  [Custom]  to make the registration.

When the registration is complete, the steering wheel remote control becomes available.

Notes on installing the connection cable RC-SR1 

• Refer to the support site on the back cover for details then connect each lead properly to the appropriate leads.

Making an improper connection may damage the unit.

• Consulting the dealer or an experienced technician for help is recommended.

When using the wired remote control

1

To enable the wired remote control, set [Steering

Control] in [General] to [Preset].

Using the rear view camera

Installation of the rear view camera (not supplied) is required before use.

The picture from a rear view camera connected to the CAMERA IN terminal is displayed when:

– the back lamp of your car lights up (or the shift lever is set to the R (reverse) position).

– you press HOME, then touch [Rear Camera].

Installation

Mounting the unit in a Japanese car

You may not be able to install this unit in some

Japanese cars. In such a case, consult your Sony dealer.

To the dashboard/center console

Bracket

Bracket

Parts supplied with your car

When mounting this unit to the preinstalled brackets of your car, use the mounting screws  in the appropriate screw holes based on your car:

T for TOYOTA and N for NISSAN.

Note

To prevent a malfunction, install only with the mounting screws

.

Fuse replacement

When replacing the fuse, be sure to use one matching the amperage rating stated on the original fuse.

If the fuse blows, check the power connection and replace the fuse.

If the fuse blows again after

Fuse (10 A) replacement, there may be an internal malfunction. In such a case, consult your nearest Sony dealer.

15

GB

Support site

If you have any questions or for the latest support information on this product, please visit the web site below:

https://www.sony-asia.com/support

Help Guide (online manual)

For more details, please visit the following web site and refer to your unit name as shown below.

XAV-AX5500(IN) https://rd1.sony.net/help/ev/xav-ax55/h_zz

©2020 Sony Corporation Printed in Thailand https://www.sony.net/

advertisement

Key Features

  • Large 6.95-inch touchscreen for easy control
  • Apple CarPlay and Android Auto™ integration for seamless smartphone connectivity
  • Built-in amplifier for high-quality audio
  • Hands-free calling for safe and convenient communication
  • Sleek and modern design to complement any vehicle's interior

Related manuals

Frequently Answers and Questions

How do I cancel the demonstration display?
Refer to page 8 of the Operating Instructions.
How do I switch the FM/AM tuning step?
Refer to page 7 of the Operating Instructions.
Where can I find the connection and installation instructions?
Refer to page 12 of the Operating Instructions.
What should I do if my car's ignition has no ACC position?
Do not install this unit in such a car, as the display will not turn off even after turning the ignition off, causing battery drain.