FOR-A FA-1010, FA-10PS Operation Manual
Pubblicità
Pubblicità
OPERATION
MANUAL
FA-1010
Frame Synchronizer
FA-10PS
1
st
Edition - Rev.2
Version 1.10 or Higher
Edition Revision History
Edit. Rev. Date
-
1
-
-
2013/07/31
2013/08/30
1
1
1
2
2013/09/02
2013/09/18
Description
Provisional
First edition
Corrected one dimension.
Added Audio functions.
Section/Page
7-1
4-3, etc.
2
Precautions
Important Safety Warnings
[Power]
Caution
Stop
Operate unit only at the specified supply voltage.
Disconnect the power cord via the power plug only. Do not pull on the cable portion.
Do not place or drop heavy or sharp-edged objects on the power cord. A damaged cord can cause fire or electrical shock hazards. Regularly check the power cord for excessive wear or damage to avoid possible fire / electrical hazards.
[Grounding]
Caution
Hazard
Caution
Ensure the unit is properly grounded at all times to prevent electrical shock.
Do not ground the unit to gas lines, units, or fixtures of an explosive or dangerous nature.
Ensure the power cord is firmly plugged into the AC outlet.
[Operation]
Hazard
MHazard
Do not operate the unit under hazardous or potentially explosive atmospheric conditions. Doing so could result in fire, explosion, or other hazardous results.
Do not allow liquids, metal pieces, or other foreign materials to enter the unit. Doing so could result in fire, other hazards, or a unit malfunction.
If a foreign material does enter the unit, turn the power off and immediately disconnect the power cord. Remove the material and contact an authorized service representative if damage has occurred.
[Transportation]
Caution
Handle with care to avoid impact shock during transit, which may cause malfunction. When you need to transport the unit, use the original or suitable alternative packing material.
3
[Circuitry Access]
Stop
Hazard
Do not remove covers, panels, casing, or access the circuitry with power applied to the unit. Turn the power off and disconnect the power cord prior to removal. Internal servicing / adjustment of unit should only be performed by qualified personnel.
Do not touch any parts / circuitry with a high heat factor.
Capacitors can retain enough electric charge to cause mild to serious shock, even after the power has been disconnected. Capacitors associated with the power supply are especially hazardous.
Unit should not be operated or stored with cover, panels, and / or casing removed.
Operating the unit with circuitry exposed could result in electric shock / fire hazards or a unit malfunction.
[Potential Hazards]
Caution
If abnormal odors or noises are noticed coming from the unit, immediately turn the power off and disconnect the power cord to avoid potentially hazardous conditions.
If problems similar to the above occur, contact an authorized service representative before attempting to operate the unit again.
[Rack Mount Brackets, Ground Terminal, and Rubber Feet]
Caution
To rack-mount or ground the unit, or to install rubber feet, do not use screws or materials other than those supplied. Doing so may cause damage to the internal circuits or components of the unit. If you remove the rubber feet that are attached to the unit, do not reinsert the screws that secure the rubber feet.
[Consumables]
Caution
Consumable items that are used in the unit must be periodically replaced. For further details on which parts are consumables and when they should be replaced, refer to the specifications at the end of the Operation Manual. Since the service life of the consumables varies greatly depending on the environment in which they are used, such items should be replaced at an early date. For details on replacing consumable items, contact your dealer.
4
Upon Receipt
Unpacking
FA-1010 units and their accessories are fully inspected and adjusted prior to shipment.
Operation can be performed immediately upon completing all required connections and operational settings.
Check your received items against the packing lists below. Check to ensure no damage has occurred during shipment. If damage has occurred, or items are missing, inform your supplier immediately.
ITEM QTY REMARKS
FA-1010
AC Cord
Rack Mount Brackets
CD-ROM
Quick Setup Guide
1
1 set
1 set
1
1
(Including AC cord retaining clip)
EIA standard type (Including 4 screws)
Windows GUI installation disc
(Including operation manual (PDF))
Option
FA-10PS
ITEM QTY
1 set
REMARKS
Redundant power supply unit (Including AC cord and AC cord retaining clip).
FA-10ANA-AUD 1 Analog audio I/O card
FA-10AES-BL 1-4 Digital audio (balanced) I/O card
FA-10AES-UBL
FA-10AES-UBLC
1-4
1-4
1
Digital audio (unbalanced) I/O card
Digital audio (unbalanced) Output expansion cable
* The FA-10AES-UBL functions as an input card when used with the FA-10AES-UBLC.
GPI control card FA-10GPI
Trademarks
Microsoft , and Windows are either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries.
Intel, Intel Core, Pentium are trademarks of Intel Corporation in the U.S. and/or other countries.
* All other trademarks are trademarks or registered trademarks of their respective owners.
Rack Mounting
FA-1010 can be mounted to EIA standard rack units. When rack mounting a unit, remove the rubber feet and use the accessory rack mount brackets (rack ears).
5
Table of Contents
6
7
1. Prior to Starting
1-1. Welcome
Congratulations! By purchasing a FA-1010 Frame Synchronizer you have entered the world of
FOR-A and its many innovative products. Thank you for your patronage and we hope you will turn to FOR-A products again and again to satisfy your video and audio needs.
FOR-A provides a wide range of products, from basic support units to complex system controllers, which have been increasingly joined by products for computer video-based systems.
Whatever your needs, talk to your FOR-A representative. We will do our best to be of continuing service to you.
1-2. Features
Developed as an all-round unit, the FA-1010 frame synchronizer comes equipped with 10 signal processing channels in a compact 1RU body. Color correction and logo generation video signal processing functions and remapping/embedding of 160-channel embedded audio in 10 SDI signal inputs have been added as standard to the various frame synchronizer functions of the
FA-1010. Moreover, by installing additional optional functions into the 4 built-in slots, the unit is able to function optimally under all types of video production scenes, including those for transmission, outside broadcasting, news reporting, production, editing and distribution.
Standard Features
Color correction
Powerful frame synchronizer
Audio embedding
3G-SDI support (Level A)
Routing
Pass-through of ancillary data such as closed captioning or time code data
Other standard features
Video delay
Monitoring and control via dedicated GUI
SNMP monitoring
Optional Features
Redundant power supply
Analog audio input/output (Planned option)
Digital audio input/output (balanced/unbalanced) (Planned option)
GPI control (Planned option)
1-3. About This Manual
This manual is intended to help the user easily operate this product and make full use of its functions during operation. Before connecting or operating your unit, read this operation manual thoroughly to ensure you understand the product. Afterwards, it is important to keep this manual in a safe place and available for reference.
9
2. Panel Descriptions
2-1. Front Panel
(1)
DC POWER 1
DC POWER 2
FAN ALARM
GENLOCK
(2)
LTC IN
No Name
1 Power switch
BY-PASS
1
VIDEO
AUDIO
2 3 4
SDI IN
5 6 7 8 9 10
(3)
INSTALL
OPTION SLOT
A B C D
VIDEO IN
AUDIO IN
INITIALIZATION
(4) (5)
FA- 1010
FRAME SYNCHRONIZER
2
3
4
Unit status indicator
SDI IN status indicator
OPTION SLOT status indicator
5 INITIALIZATION
Description
Used to turn the unit ON / OFF.
DC
POWER
1/2
Lit green Power supply is normal.
Lit red A power failure has occurred.
FAN
ALARM
GENLOCK
Lit green All fans are operating normally.
Lit red One or more fans have failed.
Lit green Genlock signal input is present.
Unlit No genlock signal input is present.
LTC IN
BY-PASS
VIDEO
AUDIO
Lit green LTC input is present.
Unlit No LTC input is present.
Lit green Input signal is being bypassed.
Unlit No signal is being bypassed.
Lit green Video signal input is present.
Unlit No video signal input is present.
Lit green Embedded audio signal is present.
Unlit No embedded audio signal is present.
INSTALL
VIDEO IN
Lit green
Unlit
Lit green
One or more option cards are found and recognized in option slots A to D.
No option card is installed or recognized.
Video signal input(s) is/are present in option slot(s).
No video signal input in option slots. Unlit
AUDIO IN
Lit green
Audio signal input(s) is/are present in option slot(s).
No audio signal input in option slots. Unlit
Used to reinitialize the unit. Read the WARNING below before proceding. To reinitialize the unit, turn the unit on while holding down the INITIALIZATION button.
WARNING
All setting data will initialize. Back up before executing a reinitialization.
10
2-2. Rear Panel
(6) (7)
LTC IN / OUT
LAN
(1)
IN 1 OUT 1 IN 2
A
(8)
OUT 2 IN 3 OUT 3 IN 4 OUT 4
(9)
B
IN 5 OUT 5 IN 6
3G / HD / SD - SDI
OUT 6
C
(10)
IN 7 OUT 7 IN 8 OUT 8
(2) Left connector. (3) Right connector.
IN 9
(11)
D
OUT 9 IN 10 OUT 10
GENLOCK IN
(12)
(4) (5)
No
1
2
3
Name
LAN
SDI IN 1-10
SDI OUT 1-10
Description
1000/100BASE-TX Ethernet LAN port. Used to connect to an external remote control unit or transfer data to an external device. RJ-45
3G/HD/SD-SDI video signal input connectors. Each IN and OUT 1 to 10 are allocated as a pair. The left connectors of each pair are input connectors.
3G/HD/SD-SDI video signal output connectors. Each IN and OUT 1 to 10 are allocated as a pair. The right connectors of each pair are output connectors.
4
5
GENLOCK IN
Ground
Terminal
Genlock signal input connector. Used for reference signal input (black burst or tri-level sync). The bottom connector is for a loop through. Terminate at
75 ohm when not in use.
Used to ground the unit to protect operators from static electricity and electrical shock.
6 AC IN 2 AC power source connector. (100-240V AC 50/60Hz)(optional)
7 LTC IN/OUT Time code input/output connector
8 Option Slot A Option card installation slot.
9 Option Slot B Option card installation slot.
10 Option Slot C Option card installation slot.
11 Option Slot D Option card installation slot.
12 AC IN 1 AC power source connector. (100-240V AC 50/60Hz)
IMPORTANT
Internal cooling fans prevent overheating. Do not block the front, rear or side vents with other equipment or objects.
11
2-3. Internal Settings
IMPORTANT
Note that internal switch settings should remain unchanged from factory default settings under most operational circumstances. If you have accidentally changed the setting, refer to the MAIN card settings below to return to the factory default settings.
Further note that adjustment and maintenance should only be performed by qualified technical personnel familiar with FOR-A equipment.
WARNING
Do not access internal cards or connect peripheral units with the unit power ON.
Always power OFF all connected units / disconnect power cords prior to accessing the interior. To protect boards from electrostatic damage, do not touch board components.
2-3-1. Dipswitch Settings
The following dipswitch settings can be made on the MAIN CARD inside the FA-1010.
Dipswitch DS1 Settings
Pin No.
DS1
DS2
1-8
1
2-8
Default
OFF
ON
OFF
Do not change
Settings
Do not change
12
3. System Setup
3-1. System Configuration
FA-1010 base system device connections are shown below with the 10 SDI inputs and outputs standard.
LTC IN/OUT
Time code input and output SLOT A
Option slots
SLOT B SLOT C SLOT D
GENLOCK IN
External reference signal input
GENLOCK IN
Loop-through
(Terminate at
75
Ω when not in use.)
LTC IN / OUT
LAN
IN 1 OUT 1 IN 2
A
OUT 2 IN 3 OUT 3 IN 4
B
OUT 4 IN 5 OUT 5 IN 6
3G / HD / SD - SDI
OUT 6
C
IN 7 OUT 7 IN 8 OUT 8 IN 9
D
OUT 9 IN 10 OUT 10
GENLOCK IN
AC IN 1 AC IN 2(option)
Hub
Windows GUI
LAN
3-1-1. Option Slots
SDI IN
・・・・
モニター
モニター
SDI OUT
・・・・
モニター
モニター
Cameras, switchers, etc. Monitors, recorders, etc.
3G/HD/SD-SDI input and output connectors.
Alternate Input and output allocation. Bypass outputs signal input (left) to the right of each input/output connector pair.
Up to 4 option cards can be installed into SLOTS A to D to enhance your system.
Currently available options are as follows:
FA-10ANA-AUD
Analog audio input/output option
FA-10AES-BL
Digital audio (balanced) input/output option
FA-10AES-UBL
Digital audio (unbalanced) input/output option
FA-10AES-UBLC
Digital audio (unbalanced) input/output expansion option
FA-10GPI
GPI control option
13
3-2. Power-On
When the FA-1010 is powered on, all LEDs on the front panel including Alarm indicators light.
Once startup is complete, current status is indicated.
3-2-1. Note on Powering Off
Do not turn the power of the unit for at least 10 seconds whenever a setting is changed.
Otherwise the setting data may not be properly saved.
3-3. Windows GUI Setup
3-3-1. System Requirements
To install Product (software), your computer must meet the following requirements.
OS
CPU
Memory
Windows® 7, 8 operating system
Professional (32/64 bit)
Intel® Core ™2 Duo processor
2 GHz or faster
2 GB or more
Display Resolution of 1280 x 1024pixels or higher recommended
Must be capable of full color (24-bit) display
Network port Ethernet, at least one port
100BASE-TX/1000BASE-T
Network cable 100BASE-TX: Category 5 or better
1000BASE-T: Category 6, or enhanced category 5
Software Microsoft® .NET Framework 4.0
Windows® Installer 3.1
* Mac OS is not supported.
3-3-2. Network Settings
Change the PC network settings for the connection with the FA-1010.
From the Startup menu, go to Local Area Connection > General > Internet Protocol
(TCP/IP) > General > Properties , then set the IP address and Subnet mask as shown below.
PC IP address
192.168.0.xxx (xxx is any number from 1 to 254 except for the number set for the FA-1010 unit and the gateway number.)
255.255.255.0
Subnet mask
* The default FA-1010 IP address is 192.168.0.10.
14
3-3-3. Installing Software
(1) Open the CD-ROM, and the FA-1010GUI folder. Double-click the Setup icon to start the setup wizard.
(2) If “Microsoft .NET Framework 4” is not installed on your PC, the screen as sown below appears. Click Accept.
* If “Microsoft .NET Framework 4” is already installed on your PC, the screen will not appear.
(3) If “Microsoft Visual Basic Power Packs 10.0” is not installed on your PC, the screen as shown below appears. Click Accept .
* If “Microsoft Visual Basic Power Packs 10.0” is already installed on your PC, the screen will not appear.
15
(4) Once the FA-1010GUI setup wizard starts, the screen as shown below appears. Click
Next to continue the setup.
(5) Select the installation directory, then click Next .
(6) A confirmation screen will appear. Click Next to start the installation.
(7) The user Account Control screen will appear. Click Yes to continue the installation.
16
(8) When installation is completed, the screen as shown below appears. Click Close to quit the setup wizard.
17
4. Windows GUI
This section describes Windows GUI, the dedicated FA-1010 control software that runs in a PC.
Refer to section 3-3-2. “Network Settings” when establishing a PC connection.
When FA-1010 GUI starts up, a page as shown below opens.
Enter the FA-1010 IP address to register the unit. Up to 10 units can be registered.
Select a unit to connect under Select, then click Connect. A menu page opens.
* Simultaneous connections with multiple units are not possible.
Item Description
Select
IP Address
Description
Allows you to select an FA-1010 to connect or enter Unit and FS names.
Allows you to enter the IP address of each FA-1010 unit.
Allows you to enter a note.
Button
Connect
Disconnect
Abort
Description
Allows you to establish a connection with the selected FA-1010.
Allows you to release the connection.
Allows you to cancel the connection.
18
4-1. Main Unit
The Main Unit tab at the top of the screen allows you to open the Main Unit page as shown below.
Windows GUI allows you to register up to 10 FA-1010 units with unit names and FS names.
Select
Item
IP Address
Description
Unit / FS Name
Description
Allows you to select an FA-1010 to connect or enter Unit and FS names. The FA-1010 unit selection cannot be changed while one unit is connected.
Allows you to enter the IP address. The IP address cannot be changed while the unit is connected.
Allows you to enter a note. Unchangeable during connection.
Allows you to enter the unit name and FS names for the selected
FA-1010.
Button
Connect
Disconnect
Apply
Description
Allows you to establish a connection with the selected FA-1010.
Allows you to release the connection. Release the current connection to connect to another FA-1010 unit.
Allows you to apply settings.
* Unit/FS Name is visible and changeable only if an FA-1010 is connected.
19
4-2. Video Block (Video Signal Control)
Click the Video tab at the top of the page. The video block diagram will be displayed.
Each block in the diagram lets you go to the corresponding windows or dialog boxes that allow you to change various settings.
20
4-2-1. FS Input
The Video Input page allows you to assign input video signals to FS 1 to 10.
Item Default Setting range Description
Frame Rate 29.97/59.94 fps
FS Name
Matrix
-
-
29.97/59.94 fps
25/50 fps
-
SDI1-10
Allows you to select a frame rate for the format selected under Sync
Format.
Displays the name set in the Main
Unit page.
Allows you to select input video signals to input to FS 1 to 10.
Sync
Format
Auto
When Frame rate is set to 29.97/59.94 fps
Auto
1080/59i
1080/59p
720/59p
When Frame rate is set to 25/50 fps
Auto
1080/50i
1080/50p
720/50p
Allows you to select video signal input formats for FS 1 to 10.
21
4-2-2. Video Loss Mode
The Video Loss Mode page allows you to select an operation for video signal loss.
Item Default Setting range Description
FS1-10 Black
Black
Blue
Red
Magenta
Green
Cyan
Yellow
Color Bar
Auto Freeze
Disable
Allows you to select an operation for the time the signal input selected under Input is lost.
Black – Yellow: Outputs the selected back color.
Color Bar: Outputs a color bar.
Auto Freeze: Continues to output the image of one frame before the input signal loss.
Disable: No signal output.
* Auto Freeze is effective only if Sync Mode is set to Frame. If not, the operation will be the same as in Black (back color).
22
4-2-3. Video System
The Video System page allows you to change frame synchronization settings.
Item Default Setting range Description
FS
All Freeze
FS1
OFF
FS1-FS10
ON
OFF
Allows you to select an FS for it to set Frame
Synchronizer settings.
Allows you to freeze all FS1 to FS10 output videos.
Freeze operation in each FS1 to FS10 varies depending on the Freeze mode selection (see sec.
4-2-4-4. “Freeze Mode”).
4-2-3-1. Sync Mode
Item
Sync Mode
Default Setting range
Frame
Frame
Line
AVDL
Description
Frame : Enables horizontal and vertical alignment of video signals to a genlock signal. Effective on both synchronous and asynchronous signals.
Line : Locks the video signal of within ±1/2H to a genlock signal. Output delay is 1H. Effective only when video signal is synchronous to the genlock signal.
AVDL : Locks the video signal to a genlock signal with a 1H delay. Effective only when video signal is synchronous to the genlock signal.
IMPORTANT
Input signals of 1080/59.94p Level-B or 1080/50p Level B are output with a 3H delay when Sync Mode is set to AVDL.
Table of Reference signals and Input formats that can lock
Reference signal
Input signal
525/60
1080/59i
720/59p
1080/59p
625/50
1080/50i
720/50p
1080/50p
1080/23PsF
525/60
✓✓✓
✓✓✓
✓✓✓
✓✓✓
-
-
✓
-
-
-
1080/59i 720/59p
✓✓✓
✓✓✓
✓
✓
✓✓✓
✓✓✓
-
-
✓✓✓
✓✓✓
-
-
✓
-
-
-
✓
-
-
-
625/50
-
-
-
-
✓✓✓
✓✓✓
✓✓✓
✓✓✓
-
✓
1080/24PsF
✓✓✓
: SYNCHRO can be set to FRAME, LINE, or AVDL.
✓
: SYNCHRO can only be set to FRAME.
-
: Unable to synchronize.
1080/50i
-
-
-
-
✓✓✓
✓✓✓
✓✓✓
✓✓✓
-
✓
720/50p
-
-
✓
-
-
✓
✓✓✓
✓✓✓
-
✓
23
4-2-3-2. System Phase
* The settings are not available if there is no reference signal input.
Item Default
Setting range
(Steps)
Description
Horizontal 0
± 1300
(1 Clock)
Vertical
Unity (button)
0
（ FRAME ）
1
（ LINE, AVDL ）
-
± 600
(1 Line)
-
Allows you to adjust the horizontal and vertical phases of the system referring to genlock signal.
Allows you to reset the settings to default.
4-2-3-3. Video Position
Item
Horizontal
Vertical
Default
0
0
Unity (button) -
4-2-3-4. Freeze Mode
Setting range
(Steps)
± 200
（ 2 Pixel ）
± 100
(1 Line)
-
Item
Freeze
Mode
Strobe
Unity (button)
Default
On
Frame
0
-
Setting range
Off, On
Frame
Odd, Even
0 - 255
-
Description
Adjusts the horizontal/vertical position of output videos.
Allows you to reset the settings to default.
Description
Allows you to turn Freeze On/Off .
Allows you to select an operation mode for
Freeze.
Allows you to set the interval to refresh the images by the number of fields for the field or frame freeze.
0: Images will not be refreshed.
Allows you to reset the settings to default.
24
4-2-4. Frame Delay
The Frame Delay page allows you to set frame delay for each FS separately.
* Settings are effective only if Sync Mode is set to Frame.
Item Default Setting range Description
Frame Delay Off
Off
1 - 8 Frames
Allows you to set the amount of frame delay for each FS.
25
4-2-5. Video Process Amplifier
The Video Process Amplifier page allows you to set Process Amp settings for each FS separately.
Item Default Setting range Description
FS
FS Link
FS1
-
FS1-FS10
FS1-FS10
Allows you to select an FS for which to set Process Amp settings.
Allows FS settings to be simultaneously adjusted.
Designate a base FS from those selected under FS Link >
FS. All other FS settings are adjusted in the same increments as those of the base FS.
Item
Video Level
Default Setting range (Steps) Description
100.0% 0.0 - 200.0% (0.1%) Allows you to adjust the video level.
Chroma Level
Setup/Black Level
100.0%
0.0%
0.0 - 200.0% (0.1%)
Allows you to adjust the chrominance level.
-20.0 - 100.0% (0.1%) Allows you to adjust the black level.
Hue 0.0° -179.8° - 180.0° (0.2°)
Allows you to adjust the Chroma phase.
Unity (button) - -
Allows you to reset all settings in this page to default.
* Chroma Level and Hue settings are ineffective if Correction Mode is set to Sepia.
IMPORTANT
In Link mode, the amount adjusted for the FS selected under FS will be applied to other FSs. The resulting setting values of Linked FSs may differ. If the adjusted value exceeds the upper/lower limit, the resulting setting value will be clipped at the limit. If the FS selected under FS is not selected under FS Link, Link mode settings are ineffective.
26
4-2-5-1. Link Mode Setting Example
Example 1: Linked
Select F1 under FS.
Select FS1, FS2, and FS3 under FS Link.
FS1 is selected under FS and FS Link.
The amount adjusted for the FS1 setting will be applied to FS2 and FS3.
Example 2: Unlinked
Select F1 under FS.
Select FS2 and FS3 under FS Link.
FS1 is selected only under FS.
Only FS1 settings will be adjusted.
IMPORTANT
Link mode is ineffective if the FS selected under FS is not selected under FS Link, or if
Color Correction Mode and/or Video Clip Mode settings are different between selected FSs.
27
4-2-6. Color Corrector
The Color Corrector page allows you to separately adjust color correction settings for each
FS.
Item Default Setting range Description
FS
FS Link
FS1
-
Correction Mode Balance
FS1-FS10
FS1-FS10
Balance
Differential
Sepia
Allows you to select an FS for which to adjust color correction settings.
Allows FS settings to be simultaneously adjusted. Designate a base FS from those selected under FS Link > FS. All other FS settings are adjusted in the same increments as those of the base FS.
Allows you to select a correction mode from
Balance (RGB), Differential (YPbPr), or Sepia.
Balance: RGB signal correction mode
Allows you to adjust the white balance. Gray scale can be changed by adjusting R, G and
B levels.
Differential: Color difference signal mode
Allows you to adjust contrast without changing white balance. R, G and B levels can be changed without affecting gray scale.
This adjustment is effective for images with different color saturation levels.
Sepia: Sepia mode
Useful for creating black and white images.
Sepia mode cannot be selected in Link mode.
IMPORTANT
In Link mode, the amount adjusted for the FS selected under FS will be applied to other FSs. The resulting setting values of Linked FSs may differ. If the adjusted value exceeds the upper/lower limit, the resulting setting value will be clipped at the limit. If the FS selected under FS is not selected under FS Link, Link mode settings are
ineffective.See section 4-2-5-1. “Link Mode Setting Example” for further information
on Link mode settings.
28
White Level settings
Item Default
RED, GREEN, BLUE 100.0%
GROUP ADJUST
(Group Adjustment)
Unity (button)
OFF
-
Setting range
(Steps)
0.0 - 200.0%
(0.5%)
OFF
ON
-
Description
Allows you to adjust the white level of R,
G, and B components separately.
Allows you to adjust the white level of R,
G, and B components all together while retaining the proportion of the separately adjusted levels.
Allows you to reset the settings to default.
Black Level Settings
Item Default
RED, GREEN, BLUE 100.0%
GROUP ADJUST
(Group Adjustment)
Unity (button)
OFF
-
Setting range
(Steps)
0.0 - 200.0%
(0.5%)
OFF
ON
-
Description
Allows you to adjust the black level of R,
G, and B components separately.
Allows you to adjust the black level of R,
G, and B components all together while retaining the proportion of the separately adjusted levels.
Allows you to reset the settings to default.
Gamma Level Settings
Item
Gamma Curve
Default
RED, GREEN, BLUE 100.0%
GROUP ADJUST
(Group Adjustment)
Unity (button)
Center
OFF
-
Setting range
(Steps)
Black
Center
White
0.0 - 200%
(0.5%)
Description
Allows you to select a gamma curve type.
OFF
ON
-
Allows you to adjust the gamma level of
R, G, and B components separately.
Allows you to adjust the gamma level of
R, G, and B components all together while retaining the proportion of the separately adjusted levels.
Allows you to reset the settings to default.
Sepia Settings
Item
Level
Color
Unity (button)
Default
25.0%
-160.0°
-
Setting range
(Steps)
0.0 - 100 ％
(0.1
％ )
-179.8° - 180.0°
(0.2°)
-
Description
Allows you to adjust the color level in the
Sepia mode.
Allows you to adjust the color in the Sepia mode.
Allows you to reset the settings to default.
29
4-2-7. Video Clip
Item
FS
FS Link
Default Setting range
FS1 FS1-FS10
Description
Allows you to select an FS for which to adjust settings.
- FS1-FS10
Allows FS settings to be simultaneously adjusted.
Designate a base FS from those selected under FS
Link > FS. All other FS settings are adjusted in the same increments as those of the base FS.
Clip Mode Clip OFF
Clip OFF
YPbPr Clip
RGB Clip
Selects a mode whether to clip signals in the color space or RGB color space.
YPbPr
IMPORTANT
In Link mode, the amount adjusted for the FS selected under FS will be applied to other FSs. The resulting setting values of Linked FSs may differ. If the adjusted value exceeds the upper/lower limit, the resulting setting value will be clipped at the limit. If the FS selected under FS is not selected under FS Link, Link mode settings are
ineffective. See section 4-2-5-1. “Link Mode Setting Example” for further information
on Link mode settings.
YPbPr Clip
Item
Y White
(Y White Clip)
Y Black
(Y Black Clip)
Chroma
(YPbPr Chroma Clip)
Unity (button)
RGB Clip
Item
White
(RGB White Clip)
Black
(RGB Black Clip)
Unity (button)
Default
109.0%
-7.5%
111.0%
-
Default
300.0%
-200.0%
-
Setting range
(Steps)
50.0 - 109.0%
(0.5%)
-7.5 - 50.0%
(0.5%)
50.0 - 111.0%
(0.5%)
-
Description
Sets the Y signal upper threshold.
Sets the Y signal lower threshold.
Sets both the upper and lower thresholds of PbPr signals.
Allows you to reset the settings to default.
Setting range
(Steps)
50 - 300%
(0.5%)
-200 - 50%
(0.5%)
-
Description
Sets the upper threshold of RGB color space.
Sets the lower threshold of RGB color space.
Allows you to reset the settings to default.
30
Video Clip Setting Ranges
Y Signal Settings
① Y White Clip Level
Setting range 50 - 109 ％ (Default: 109 ％ )
100%
109%
50%
Y white clip level setting range
50%
0%
SMPTE 100% color bar when 100% white.
② Y Black Clip Level
Setting range -7.5 - 50 ％ (Default: -7.5
％ )
100%
50%
0%
50%
SMPTE 100% color bar when 100% black.
③ C White Clip Level
Setting range 50 - 111 ％ (Default: 111 ％ )
Y Black clip level setting range
-7.5%
50%
50%
100%
111% (default)
SMPTE 100% color bar when color 700mVp-p.
RGB CLIP
To adjust the RGB clipping, select the RGB
CLIP under CLIP MODE, and then set RGB
White Clip and RGB Black Clip.
Once the “RGB CLIP” is selected, the YPbPr input video signal is converted into an RGB signal in the unit. The converted RGB signal is processed so as not to exceed the RGB gamut range set under the RGB White Clip and RGB Black Clip parameters in the menu.
Then the processed RGB signal is converted again to YPbPr format. This correction is used to eliminate out-of RGB gamut problems.
300%
100%
50%
0%
-200%
RGB Clip Processing
31
White setting range
Black setting range
4-2-8. Video Test Signal
The Video Test Signal page allows you to separately set test signal output for each FS.
Item Default Setting range Description
All
FS1-10
Off
Off
Off
100% Color Bar
75% Color Bar
SMPTE Color Bar
Ramp
Off
100% Color Bar
75% Color Bar
SMPTE Color Bar
Ramp
Allows you to set all FSs to generate the selected video test signal.
Allows you to set each FS to generate the selected video test signal.
32
4-2-9. SDI Multiplexer
The SDI Multiplexer page allows you to separately select ancillary data output mode for each
FS.
Item Default Setting range Description
Horizontal
Vertical
Overwrite
Overwrite
Overwrite
Pass
Blank
Overwrite
Pass
Blank
Allows you to embed signals into horizontal ancillary data of FS1-10 output videos.
Overwrite: Removes the embedded HANC data from the input SDI video, then embeds the processed data in the video signal.
The input SDI data will be embedded in the video signal after audio signals are embedded.
Pass: Embeds the HANC data without processing. (Processed audio data cannot be embedded.)
Blank : Deletes all horizontal ancillary data, and embeds the processed audio data.
Allows you to embed signals into vertical ancillary data of FS1-10 output videos.
Overwrite : Embeds the processed VANC data.
Pass : Embeds the VANC data without processing.
Blank : Deletes all VANC data.
33
4-2-9-1. Embedded Audio Multiplexer
This page allows you to select whether to embed audio signals for each audio group.
Item
FS 1-10
Default
Enable
(Blue)
Setting range
Disable (Gray)
Enable (Blue)
Description
Allows you to select or unselect each FS
Group to enable (blue) or disable (gray) embedded audio insertion.
34
4-2-9-2. Timecode
Output
Item Default
FS 1-10 Pass
Setting range
Pass
LTC In
TCG Out
Description
Allows you to select a timecode to embed to
SDI output signals.
Pass: Uses the timecode embedded into
SDI signals without processing.
LTC In: Embeds and outputs the input timecode via the rear panel IN/OUT connector to the SDI output signal.
TCG Out : Embeds the timecode generated by the Time Code Generator into SDI output signal.
LTC Input / Output Setting
Item Default Setting range Description
Allows you to set the LTC IN/OUT connector on the rear panel for input use or output use.
Timecode is displayed above the input and output buttons.
LTC Setting Input
Input
Output
Timecode Generator
Item
Start (button)
Default
-
Setting range
-
Stop (button)
Reset (button)
Preset (button)
Edit (button)
Drop Frame
-
-
-
-
OFF
-
-
-
-
OFF
ON
Description
Allows you to start counting the internally generated timecode.
Allows you to stop counting the internally generated timecode.
Allows you to reset the internally generated timecode to 00:00:00:00.
Allows you to set the timecode to the Preset time.
Allows you to edit Preset timecode settings.
OFF: non Drop
ON: Drop
35
4-2-10. Clean Switch
Item
Operation
Mode
Matrix
Take (button)
Reset (button)
Default
Direct Mode
Dest.1-Src.1
｜
Dest.10-Src.10
-
-
Setting range
Direct Mode
Take Mode
Salvo Mode
Src.1-10
-
-
Description
Allows you to select the Clean switch operation mode.
Direct Mode: Selecting a cross point immediately switches the cross point.
Take Mode: The Take button switches multiple preset cross points simultaneously.
Salvo Mode: Multiple cross point matrices can be saved to select and use later.
Allows you to select signals to be output from Destination 1-10 (output signals assigned to FS1-10) from Src 1-10 (input signals assigned to FS1-10).
A same signal can be selected for multiple
Destinations.
Displayed in Take Mode. Allows you to simultaneously switch multiple cross points set in the Matrix.
Displayed in Take Mode. Allows you to reset
36
4-2-10-1. Take Mode Operation
Take Mode allows you to simultaneously switch multiple channels.
Blue-highlighted crosspoints in the below figure are currently effective source selections.
Source selection changes are displayed in yellow as pre-selections in the left figure.
Pressing the Take button switches crosspoints set as the pre-selections in yellow, and turns them blue as in the right figure.
IMPORTANT
Switching source signals of which following settings are set differently may produce a noise in the video and/or audio signals. To perform shockless swithching, match the following settings for source signals (FSs) to be switched.
- Sync Mode
(See sec. 4-2-3-1. “Sync Mode”.)
- System Phase (See sec. 4-2-3-2. “System Phase”.)
4-2-10-2. Salvo Mode
Salvo Mode allows you to preset 100 crosspoint matrices for later use.
Presetting Matrices
1) Select Salvo Mode, and click Edit in the Salve section, then a Salvo Memory Edit screen as shown below right opens.
Click Edit.
37
2) Set crosspoints to register.
3) Enter a name for the matrix in the Salvo Name setting box.
4) Click Apply. A message box as shown below appears, and the matrix is successfully registered.
Recalling Matrix
1) Select Salvo Mode, then select a salvo setting in the Salvo section at the bottom of the screen. The salvo crosspoint settings that are different from the current crosspoints are displayed in yellow as shown below left.
2) Click Load in the Salvo section to switch the crosspoints.
38
4-2-11. FS Output
The FS Output page allows you to assign Clean Switch output signals to output connectors.
Item Default Setting range Description
SDI 1
・
・
SDI 10
SW1 SW1-SW10
Allows you to select a clean switch output video signal to be output for each output connector.
39
4-2-12. By-pass
The By-pass page allows you to set bypass outputs.
Input signals will be output to output connectors without being internally processed.
Item Default
Setting range
Description
All Input-All Output Operate
SDI X Input
→
SDI X Output Operate
Operate
By-pass
Operate
By-pass
Allows you to set all inputs and outputs simultaneously regardless of other settings.
Operate : Processes input signals.
By-pass : By-passes input signals. e.g. Input 1
→ Output 1, Input 10 → Output
10
Allows you to set the By-pass setting for each input connector.
Operate : Processes input signals.
By-pass : By-passes input signals.
(X: connector number)
By-pass cannot be set depending on FS
Input and FS Output settings. See the important note below.
* The front panel status LED for the by-passed input connector lights green.
IMPORTANT
SDI input that is assigned in the Video Input menu (see sec. 4-2-1) to an FS with an ID
number different from that of the SDI input cannot be selected in this menu. e.g., FS 1 assigned to SDI 3, FS 5 assigned to SDI 1, 2, 3, etc.
40
4-2-13. Video Status
The Video Status page displays routings and status of each output video signals.
Display
Video (Row 1)
Video (Row 2)
Video (Row 3)
Video (Row 4)
Reference
Description
Displays input channels (SDI IN 1-10) assigned to FS 1-10 in the FS Input menu.
Displays FSs (1-10) and their signal formats assigned to Dest 1-10 in the
Clean Switch menu.
Displays source signals (SW 1-10 are the same as Dest 1-10 of the Clean
Switch menu) assigned to output connectors (SDI OUT 1-10) in the FS
Output menu.
Displays the signal format of output signals assigned to connectors SDI
OUT 1-10.
Displays the input genlock signal format.
Row 1 (FS Input) Row 2 (Clean Switch) Row 3 (FS Output) Row 4
SDI IN
1-10
×
FS
1-10
=
Src
1-10
×
Dest
1-10
SW
=
1-10
×
SDI OUT
1-10
SDI OUT 1-10 output signal format
* Shaded cells are displayed in the status display. (Src 1-10 displayed as FS 1-10.
）
* “ × ”s indicate crosspoint settings.
41
4-3. Audio Block (Audio Signal Control)
Clicking the Audio Block tab opens the Audio block diagram. Click a block to open a corresponding setting page.
*1 Available only if the FA-10AES-BL/UBL option is installed.
*2 Available only if the FA-10ANA-AUD option is installed.
42
4-3-1. Audio Input Status
Item
Embedded Audio
Display
PCM
PCM
(Silence)
NON-PCM
Unknown
Blank
-
Description
Displays the each FS embedded audio input signal status.
Detail (button) Allows you to open the Audio Input Status-Detail page
4-3-1-1. Audio Input Status - Detail
Item
Signal Status
Sync/Async
Display
PCM
PCM (Silence)
NON-PCM
Unknown
Blank
Synchronous
Asynchronous
Description
Displays the each audio channel signal state.
Displays the sync/async status of each audio channel.
43
4-3-2. Embedded Audio Demultiplex
This page allows you to set Embedded audio demultiplexing for each FS.
Item Default Setting range Description
Group
Alignment
HD-SDI
Audio Clock
Error Sense
Fade In/Out
Disable
Auto
Normal
Disable
Enable
Disable
Auto
Sync SDI
Audio Clock
Disable
Normal
Sensitive
Disable
Enable
Allows you to enable or disable automatic phase adjustment for FS1-FS10 input embedded audio groups.
Enable: Automatic adjustment
Disable: No adjustment (normal setting)
Allows you to select audio clock signal to use for de-embedding and processing audio data in
HD-SDI input signal.
Auto : De-embeds HD-SDI embedded audio data using the audio clock phase data in the embedded audio. Synchronous and asynchronous embedded audio signals from 4 audio groups can be de-embedded separately.
Audio data will be processed as synchronous data if the audio clock phase data is incorrect, or jitter is too great.
Sync SDI : All audio data in 4 audio groups are always processed as synchronous data without referring to the respective audio clock phase data.
AUD Clock : Always uses audio clock phase data in HD-SDI embedded audio data to de-embed the audio data.
Allows you to select whether to detect changes and how sensitive detection should be to such changes.
Disable : Disables mute function when change in audio status is detected. Normally not selected.
Normal : Mutes when a change on an SDI signal, ADP (Audio Data Packet), or DBN (Data
Block Number) is detected.
Normally selected.
Sensitive : Mutes when a change on channel status, or EDP (Extended Data Packet) presence (only for SD-SDI), as well as the above items, is detected.
Disable: Always passes audio signals without applying fade or mute processing.
Enable: Fades out and mutes when an error occurs, and fades in after returning to normal state.
44
4-3-3. Sampling Rate Converter (SRC)
SRC Mode can be set for signal types separately.
Item Default
Setting range
SRC Mode SRC In
Auto
SRC In
BY-PASS
Description
Allows you to set the SRC circuit to pass or by-pass audio signals per channel pair.
Auto: Sets the SRC circuit to pass signals. However, non-PCM audio signals will be by-passed.
SRC In: Sets the SRC circuit to pass both PCM or
NON-PCM signals. However, real NON-PCM signals cannot be output properly.
BY-PASS: Sets the SRC circuit to by-pass signals. Set to By-pass to output asynchronous audio signals. An
audio clock must be selected under 4-3-12.
“Embedded Audio Multiplex“ for the respective audio
groups to embed audio signals to SDI output video signals.
45
4-3-4. Polarity Mode
This page allows you to set polarity for each FS channel.
Item Default Setting range
Ch1-16 NORM
NORM
INV
Description
Allows you to set the polarity for each channel of each FS.
INV: Reverses the polarity.
46
4-3-5. Down Mix
The following parameters for Down Mix 1 to 10 (One Down Mixer in each FS) can be separately set.
Item Default
Setting range
(Steps)
Description
Down Mix
Mode
Stereo
Stereo
Surround
Monaural
Allows you to select a mode to downmix audio signals.
Surround Mix
Center Mix
Master Level
-3dB
-3dB
-3dB
-3dB
-6dB
-9dB
0
-3dB
-4.5 dB
-6dB
-3dB
Auto
Allows you to set the Ls/Rs
(surround channels) level.
0 : (∞ dB) Excludes surround channels from the downmix.
Allows you to set the C (center channel) level.
-3dB : The output level after the downmix retains the original center channel level.
-4.5dB, -6dB: Used to reduce the audio level in case it becomes too loud due to the center channel audio mixing to both the right and left channels.
Allows you to set the level for the downmixed audio signals as a whole.
If set to Auto , Down MIX Master
Level changes according to the
Downmix Mode and Surround Mix level selections.
*1
Left
Right
Center
Left S
(Surround)
Right S
(Surround)
Left: FS1-10 Ch1
Right: FS1-10 Ch2
Center: FS1-10 Ch3
Left S: FS1-10 Ch5
Right S: FS1-10 Ch6
FS1 Ch1 ～ 16
・
・
FS10 Ch1 ～ 16
AES Ch1 ～ 8
Analog Ch1 ～ 4
Displays currently selected audio input signals for downmixing.
Assign
(button)
- -
Allows you to open a window to assign audio signals to input for downmixing.
* If Master Level is set to Auto, Master Level changes as shown in the below table.
Surround Mix Level
Down Mix Mode
Stereo
Surround
Monaural
-3dB -6dB -9dB 0 (-
∞dB) approx.-7.7dB approx.-6.9dB approx.-6.3dB approx.-4.6dB approx.-9.9dB approx.-8.7dB approx.-7.7dB approx.-4.6dB approx.-12.9dB approx.-12.0dB approx.-11.4dB approx.-9.5dB
47
4-3-5-1. Downmix Assign
Clicking an Assign button in the Down Mix page opens a window as shown below allowing audio signals to be assigned to down mix channels.
Downmix Assign
Item Default Setting range
Channel
Current
Description
Allows you to assign an audio signal for each channel; Left,
Right, Center, Left S
(Surround), and Right S
(Surround).
Displays currently selected audio signals.
New Setting
Left: FS1-10 Ch1
Right: FS1-10 Ch2
Center: FS1-10 Ch3
Left S: FS1-10 Ch5
Right S: FS1-10 Ch6
FS1 Ch1 ～ 16
・
・
FS10 Ch1 ～ 16
AES Ch1 ～ 8
Analog Ch1 ～ 4
Allows you to select audio signals to input to downmixed audio channels.
48
<Surround Mix (Lt/Rt)>
Ls/Rs surround channels are summed to produce a mono surround channel and mixed to right and left channels by the 180 degree phase difference. (LFE channel is discarded.)
Gain Adjust
Gain Adjust
<Stereo Mix (Lo/Ro)>
Gain Adjust
Gain Adjust
1 ： CENTER MIX level setting
2 ： SURROUND MIX level setting
3 ： MASTER LVL setting
* LFE channel is not subjected to the mix. For Stereo Monitors
Gain Adjust
Gain Adjust
Gain Adjust
Gain Adjust
<Monaural Mix (Lo+Ro/Lo+Ro)>
For Monaural Monitors
Gain Adjust
Gain Adjust
Gain Adjust
Gain Adjust
1 ： CENTER MIX level setting
2 ： SURROUND MIX level setting
3 ： MASTER LVL setting
* LFE channel is not subjected to the mix.
Gain Adjust 1
：
CENTER MIX level setting
2
：
SURROUND MIX level setting
3 ： MASTER LVL setting
* LFE channel is not subjected to the mix.
49
4-3-6. Audio Mapping
SDI Mapping
The Audio Mapping block in the Audio Block diagram allows you to open the Audio Mapping page showing the FS signals mapping status.
Click the Assign button at the bottom of each FS column to open a setting page.
Clicking Assign at the bottom of each FS column opens a corresponding FS setting page.
Buttons in the Select Audio Group section at the left hand side in a FS audio setting page are shortcut buttons to each source group. Clicking a shortcut button displays source channels in the New Setting boxes allowing assignment.
50
FS1-10 Audio Assignment
Item Default Setting range
Channel Channel 1 Channel 1 – 16
Current -
New
Setting
EMB1 CH1 ～
16
-
FS1 Ch1-16
・
・
FS10 Ch1-16
Dowm Mix1 L
Dowm Mix1 R
・
・
Dowm Mix10 L
Dowm Mix10 R
Silence
500Hz Tone
1KHz Tone
Description
Allows you to select an audio signal to embed into respective audio channels of the selected FS.
Displays the currently assigned audio channel.
Allows you to select an audio signal to embed into respective audio channels.
Channels of audio sources selected in the Select Audio Group section are displayed.
51
4-3-7. Audio Test Signal
Item Default
All
FS1-10
OFF
OFF
Setting range
OFF
500Hz Tone
1kHz Tone
OFF
500Hz Tone
1kHz Tone
Description
Allows you to output respective internal embedded audio test signals in all FS.
Allows you to output an internal embedded audio test signal in each
FS.
52
4-3-8. Master Mute
Item Default
All Mute OFF
FS1-10 OFF
Setting range
All Mute
OFF
ON
OFF
Description
All Mute: Mutes all FS 1 to 10 audio channels that are set to be internally processed.
ON: Mutes all audio channels of each FS that are set to be internally processed.
53
4-3-9. Mono Sum Mode
This page allows Mono Sum mode to be set for each FS audio channel pair.
Item
Ch 1/2 – Ch
15/16
Default
Stereo
Setting range
Stereo
Monaural
Description
To output each FS channel pair signals in mono sum mode, set to Monaural.
54
4-3-10. Audio Gain
SDI Audio Gain (When FS1-10 are selected in the Select Audio Group section ）
Item Default
Setting range
(Steps)
Description
Ch.1-16
Master
0.0dB
0.0dB
-20.0 - +20.0 dB
(0.1 dB)
-20.0 - +20.0 dB
(0.1 dB)
Allows you to set audio gain for each audio channel.
Allows you to set an output offset for all
FS1-FS10 embedded audio channels.
55
4-3-11. Audio Delay
Item Default Setting range
Master 5 ms 5 – 1000 ms
Channel
Adjustment
5 ms 5 – 1000 ms
Description
Allows you to set a delay for all audio channels selected in the Select Audio Group section simultaneously.
Allows you to set a delay for each audio channel of the audio group selected in the Select Audio
Group section.
56
4-3-12. Embedded Audio Multiplex
・ FS1-10 Out Group Audio Clock
Item Default Setting range
Group 1
Group 2
Auto
Auto
Auto
Reference clock
CH 1/2
CH 3/4
Auto
Reference clock
CH 5/6
CH 7/8
Group 3 Auto
Auto
Reference clock
CH 9/10
CH 11/12
Group 4 Auto
Auto
Reference clock
CH 13/14
CH 15/16
Description
Allows you to select an audio clock per group for
SDI embedded audio output for FS1 to FS10 respectively.
Auto: Automatically selects audio clock input in the NON-PCM signal channel, if an input
NON-PCM signal is in the selected SDI embedded audio group. Automatically selects audio clock signal in the smallest numbered channel, if all signals in the audio group are
NON-PCM. Automatically selects audio clock signal synchronized to the output video signal, if all signals in the audio group are PCM.
Reference clock : Uses an audio clock synchronized with the output video signal. (Used to synchronize audio with the video signals processed in the SRC.)
CH 1/2 to 15/16: An input audio clock in channels 1/2 to 15/16.
To output asynchronous audio signals, select one input channel pair for each group.
*1
For SD-SDI outputs, Reference clock is automatically selected regardless of the setting.
57
4-3-13. Audio System
Item
Digital Audio
Reference
Level
Default
-20 dBFS
Digital Audio
Grade
Professional
Digital Audio
Resolution
Digital/Analog
Audio Silence
Time
Digital/analog
Audio Silence
Level
24 Bit
2 sec
-72 dBFS
Setting range
-18 dBFS
-20 dBFS
Description
Allows you to select the reference level for digital audio signals.
Professional
Consumer
Allows you to select an audio application for digital audio channels.
Professional : Optimized for professional use
Consumer : Optimized for consumer use.
16 Bit
20 Bit
24 Bit
Allows you to select an audio word length for
Digital Audio output signals.
1 – 10sec
Allows you to set the duration to determine the audio signal is silent.
-72 dBFS
-66 dBFS
-60 dBFS
-54 dBFS
-48 dBFS
Allows you to select the audio level to determine the audio signal is silent.
58
4-3-14. Audio Output Status
FS Embedded Audio
Item Display
Ch1 - Ch16
FS1-10 Ch.1-16 etc.
Description
Displays source signals assigned to FS 1 to 10.
Option Audio
Item
Ch1 - Ch8
Display
FS1-10 Ch. 1-16 etc.
Ch1 – Ch4
FS1-10 Ch. 1-16 etc.
Description
Displays source signals assigned to AES I/O connectors.
Displays source signals assigned to ANALOG AUDIO output connectors.
Audio Output Status Details
Clicking the Detail button at the bottom of each output group opens a window showing details of each channel.
Item
Assign
Status
SRC
Process
Display
-
PCM
PCM (Silence)
NON-PCM
Unknown
Blank
Processed
Bypassed
Description
Displays the assigned source signal.
Displays the type or status of embedded audio signal.
PCM: Normal audio signal
PCM (Silence): Mute signal
NON-PCM: Compressed audio data such as AC3
Unknown: Unidentifiable
Blank: No embedded audio
Displays whether the audio signal is processed in the SRC or not.
59
4-4. Status
Click the Status tab at the top of the page to open the status page.
FA-1010
Item Indication
Serial Number Displays the serial number of the unit.
Soft
FPGA 1- 5
Displays the software version.
Displays the version of each FPGA.
Fan Status
Item Indication
FAN 1-4
Normal
Stopped
Description
Displays the status of Fan1-4 respectively.
Normal : Operating normally.
Stopped : The FAN has stopped.
Turn the unit power off, and contact your dealer if a replacement is needed.
Power Supply Status
Item Indication
DC Power1
DC Power2
Normal
Abnormal
Not Installed
Description
Displays the status of power supply units respectively.
Normal : Normal
Abnormal : Error state
Turn the unit power off, and contact your dealer if a replacement is needed.
Not Installed : The power supply unit is not installed.
60
4-5. Utility
Click the Utility tab at the top of the page to open the Utility page.
4-5-1. Event Control
FA-1010 can save setting data in 100 event memories. The desired settings can be immediately recalled by loading a saved setting data.
Item Default Setting range Description
Start-up Event Load Last Setting
Load -
Last Setting
Default Settings
Event1-100
-
Last Setting : Starts up with the last set settings.
Default Settings : Starts up with default settings.
Event1 to 100 : Starts up with the settings saved as an event among events 1 to 100.
The Load button allows you to load an event.
Save
Event
Event No.
Default Settings
Event1-100
Load All
Load FS(1-10)
Only
Allows you to select an event number to be recalled.
Load
Event
Mode
Save
Event No.
Load All
-
Event 1
-
Event1-100
Allows you to select how to load event data.
*1
Load All: Loads all data in the event.
Load FS1-10 Only: Loads only the selected FS event data.
The Save button allows you to save an event to the FA-1010.
Allows you to select an event number to be saved
Event Name - -
The Event button allows you to open the
Event Name setting screen.
*2
(See sec. 4-5-1-1. “Event Name Edit”.)
*1 See section 5. “Menu List” for details on the mode difference of loading events.
*2 Event names will be displayed for Event Load/Event Save settings.
WARNING
Note that selected Default Settings reset settings, and that all data except Event data and network settings will be lost every time the FA-1010 is powered on.
61
4-5-1-1. Event Name Edit
4-5-2. Backup Parameter
The FA-1010 settings can be saved to a file, and the saved settings in a file can be loaded.
Saving the FA-1010 Settings to a File
Click Save . A window to save a file to as shown below opens.
Specify the destination directory and file name, then click Open . A “Saving in progress” message box appears.
A “Saving complete” message box appears after the file is saved.
Loading the data saved in a file
Press a button to select settings to load under Apply Setting. The button will light blue.
If no button is selected, no data will load.
62
Click Browse. A “Select the Parameter Backup File you want to restore” window opens.
Specify a destination directory, and click Open .
Click Restore . A confirmation message as shown below opens.
Click OK to start transferring file material to the FA-1010. To stop the file transfer, click
Cancel .
* Some parameters such as By-pass and Freeze settings are not stored in any Backup
Parameter.
IMPORTANT
The FA-1010 uses the CSV file format to backup the configuration data which enables commercially available spreadsheet software to edit the data. However, Unit ID or event names that consist only of numbers may be recognized as numeric values by such software and appear differently after being recalled to the FA-1010. It is recommended that alphabetical values be included in names to enable editing using such software.
4-5-3. Event Data Backup
Event Memory data (Events1 through 100) can be saved in a file on the computer as a backup. The backup data can be moved to another FA-1010.
63
Save File
Click Save . A window as shown below opens.
Specify a destination directory and file name, then click Save . A “Saving in progress” message box appears.
Once the file has been saved, a “Saving complete” message box appears.
Restore File
To load a backup file on the computer, click Browse . The “S elect the Event Data Backup
File you want to restore ” window appears.
Specify the directory and the file name and click Open . The destination path will be displayed on screen.
Click Restore . A confirmation dialog box as shown below appears.
Click OK to start loading. To stop the data upload, click Cancel .
64
4-6. Network
Clicking the Network tab at the top of the screen opens the FA-1010 Network Setting page.
4-6-1. Network Settings
Clicking the Setting button in the FA-1010 Network Settings section displays the LAN port network settings page.
Item Default Description
IP Address
Subnet Mask
Default Gateway
Port Number
192.168.0.10
255.255.255.0
0.0.0.0
50010
Allows you to set the LAN port IP address. A period “.” is used to separate each octet.
Allows you to set the LAN port subnet mask. A period “.” is used to separate each octet.
Allows you to set the gateway. A period “.” is used to separate each octet.
Allows you to set the TCP port number for the
Windows GUI connection.
Allows you to apply the settings to the FA-1010. OK (button)
4-6-2. SNMP Settings
Clicking the Setting button in the FA-1010 SNMP Settings section displays the SNMP settings page.
65
SNMP System
Item sysName sysContact
Character limit
(Alphanumeric and symbolic characters)
31 char max
31 char max sysLocation
Authen Trap
31 char max
-
Access Community
Item
Character limit
(Alphanumeric and symbolic characters)
Read Only1
Read Only2
Read/Write1
Read/Write2
19 char max
19 char max
19 char max
19 char max
Trap
Item
Trap1 Address
Character limit
(Alphanumeric and symbolic characters)
---
Trap2 Address
Trap3 Address
Trap1 Community
Trap2 Community
Trap3 Community
---
---
19 char max
19 char max
19 char max
Setting (button)
Description
Allows you to set the device name.
Allows you to enter comments regarding the device location.
Allows you to enter comments regarding the person in charge of the device.
Enable: Sends a trap if authentication fails.
Description
Read only SNMP community name
Read only SNMP community name
Read/Write SNMP community name
Read/Write SNMP community name
Description
The SNMP manager ’s IP address to which a trap is sent.
The SNMP manager ’s IP address to which a trap is sent.
The SNMP manager ’s IP address to which a trap is sent.
The community name that sends a trap to
Trap1 Address.
The community name that sends a trap to
Trap2 Address.
The community name that sends a trap to
Trap3 Address.
Allows you to apply SNMP System, Access
Community, and Trap settings to the
FA-1010.
Alert Notification
Item Default
Disable Fan
Power Unit
(Only if FA-10PS is installed)
SDI Input
Disable
-
SDI Output
Reference Input
Embedded Audio
-
Disable
-
Setting range
Disable
Enable
Disable
Enable
-
-
Disable
Enable
-
Description
Enable: Sends a trap when the fan state changes.
Enable: Sends a trap when the power supply unit state changes.
Allows you to select whether to send a trap when the SDI input signal changes for each channel.
Allows you to select whether to send a trap when the SDI output signal changes for each channel.
Enable: Sends a trap when the reference signal changes.
Allows you to select whether to send a trap when the input embedded audio state changes for each channel.
66
5. Menu List
5-1. Video Block
Menu button
FS Input
Loss Mode
Video System
Frame Delay
Process Amp
Color Corrector
Video Clip
Test Signal
SDI Multiplexer
Audio
Ancillary Data
Timecode
Clean SW
FS Output
By-pass
Video Status
Menu
Video Input
Sync Format
Video Loss Mode
Sync Mode
Video Position
System Phase
Freeze Mode
SD Line Mask
3G SDI Output
Frame Delay
Video Level
Chroma Level
Setup Black Level
Hue
Color Correction Mode
White Level
Black Level
Gamma Level
Sepia
YPbPr Clip
RGB Clip
Video Test Signal
SDI Multiplexer
Audio Multiplexer
Embedding
Embedded
Clean Switch
Operation Mode
FS Output Select
Relay By-pass
Video Status
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
No
No
Event Loading
Load All
Yes
Yes
Yes
Load FS Only
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
No
67
5-2. Audio Block
Menu button Menu
Embedded Audio
Demultiplexer
FS1-FS10 In Demux Mode
FS1-FS10 In Error Sense
Sample Rate Converter FS1-FS10 In SRC Mode
Polarity Mode
Down Mix
Mapping
Mono Sum Mode
Audio Gain
FS1-FS10 In Polarity
Down Mix 1 – Down Mix 10
FS1-FS10 Out Select
FS1-FS10 Out Mono Sum
FS1-FS10 Out Gain
All Master Mute
FS1-FS10 Out Delay Audio Delay
Embedded Audio Mux
Audio System
FS1-FS10 Mux Mode
Digital Reference Level
Audio Grade
Resolution
Silence Time
Silence Level
Test Signal
AES Audio Input
Analog Audio Input
Status
FS1-FS10 Test Signal Out
FS All Test Signal Out
I/O Setup
In Hysteresis
Input Level
Output Level
Input Terminal Setting
Microphone Input Amp Setting
Microphone Input Power Setting
(+48V)
Microphone Input Level
FS1-FS10 In Status
FS1-FS10 Out Status
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Event Loading
Load All Load FS Only
Yes
Yes
Yes
No
No
No
Yes
Yes
Yes
Yes
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
68
6. Troubleshooting
If any of the following problems occur while operating the FA-1010, follow the troubleshooting procedures below to see if the problem can be corrected before assuming a unit malfunction has occurred.
IMPORTANT
If the problem is not corrected by performing the procedures below, turn the unit off and then on again. If this still does not correct the problem, contact your dealer.
Problem
Unable to operate.
The GENLOCK status
LED remains unlit.
The POWER1 /
POWER2 status LED is lit red.
The FAN ALARM LED is lit red.
Check
Is the unit powered on? Turn the power of the unit referring to section 2-1.
Is the cable properly connecting the FA-1010 and a PC?
Connect units referring to section 2-2.
Verify the cable is shorter than 100 m. Is a proper cable used to connect the FA-1010 and a PC?
Is a genlock signal is properly input to the
GENLOCK IN connector?
Verify that a proper type cable is used as
described in section 3-3-1. “System
Verify that a genlock signal is properly
connected referring to section 2-2. “Rear
Is the power cord properly connected?
In a normal state, LEDs are as follows:
PW1 ON -> lit green
PW2 OFF -> lit red
PW1 ON - > lit green
PW2 absent -> unlit
Is anything obstructing a fan from turning?
Remedy
Verify that a power cord is properly
connected referring to section 2-2. “Rear
Panel ”. If the LED remains lit red, the
power supply unit may have a problem.
Contact your dealer for assistance.
Remove the obstruction. If the LED remains lit red, a fan(s) may have a problem. Contact your dealer for assistance.
69
7. Specifications and Dimensions
7-1. Specifications
Input Video Formats 1080/59.94i, 1080/50i, 720/59.94p, 720/50p
1080/59.94p(Level-A), 1080/50p(Level-A)
Output Video Formats 1080/59.94i, 1080/50i, 720/59.94p, 720/50p
1080/59.94p(Level-A A), 1080/50p(Level-A)
Video Input
Video Output
3G/HD-SDI: 1.5 Gbps or SD-SDI: 270 Mbps 75 Ω BNC x 10
3G/HD-SDI: 1.5 Gbps or SD-SDI: 270 Mbps 75 ΩBNC x 10
Video Processing
Quantization
Genlock Input
4:2:2 Digital Component
3G/HD/SD-SDI: 10-bit
BB: NTSC: 0.429 Vp-p / PAL: 0.45 Vp-p; or Tri-level Sync: 0.6 Vp-p,
75Ω BNC x 1, loop-through (Terminate with 75Ω terminator, if unused.)
Synchronizer mode
System Phase Control
Frame Sync mode, LineSync mode, ane AVDL mode
Frame Sync mode H phase: -1/2 H to +1/2 H
V phase: -1/2 frame to +1/2 frame
Maximum delay: 1 frame + 1H, Minimum delay: 1H
Line Sync mode H phase: -1/2 H to +1/2 H
V phase: -1/2 frame to +1/2 frame
Maximum delay: 1H +1/2 H, Minimum delay: 1/2 H
AVDL mode H phase: -1/2 H to +1/2 H
V phase: -1/2 frame to +1/2 frame
Maximum delay: 5 H +1/2 H, Minimum delay: 1/2 H (HD)
Maximum delay: 1 H +1/2 H, Minimum delay: 1/2 H (SD)
Video Delay
Video Processing
Functions
Process Amp
Video Clip
Maximum 8 frames (Frame Sync) spect ratio converter
Proc Amp
Color Corrector
Video level: 0.0% to 200.0%
Chroma level: 0.0% to 200.0%
Black level: -20.0% to 100.0%
HUE: -179.8° to +180°
YPbPr mode
RGB mode
Color Correction
Audio Input
Balance mode
Differential mode
Sepia mode
Embedded Audio 3G/HD: 16 channels (Group 1 to 4), 48 kHz, 16/20/24-bit, synchronous/asynchronous
SD: 12 channels (Group 1 to 3), 48 kHz, 16/20/24-bit, synchronous only
AES/EBU (OP) Unbalanced, 1.0 Vpp, 75Ω, BNC x 4 for AES/EBU input/output,
Maximum 4 pairs of stereo channels, 2/44.1/48 kHz, 16-bit to 24-bit
Analog Audio (OP) Balanced or unbalanced, 4 channels (2 stereo channels),
25-pin D-sub (female) x 1 for analog audio input/output,
600 Ω/high impedance 48 kHz 24-bit
Audio Output
Embedded Audio 3G/HD: 16 channels (Group 1 to 4), 48 kHz, 16/20/24-bit, synchronous/asynchronous
SD: 12 channels (Group 1 to 3), 48 kHz, 16/20/24-bit, synchronous only
AES/EBU (OP) Unbalanced, 1.0 Vpp, 75Ω, BNC x 4 for AES/EBU input/output,
Maximum 4 pairs of stereo channels, 48 kHz, 16-bit to 24-bit
70
Analog Audio (OP) Balanced or unbalanced, 4 channels (2 stereo channels),
25-pin D-sub (female) x 1 for analog audio input/output, less than 10 0Ω, 48 kHz, 24-bit
Audio Delay 5 - 1,000 ms (adjustable in 1 ms steps)
Audio Processing
Functions
Sampling rate converter (SRC)
Gain control
Down mix
Channel re-mapping
Channel mute
Interface
Ethernet
Temperature
100 Base-TX / 1000 Base-T, RJ-45 x 1
0ºC to 40ºC
Humidity
Power
30% to 90% (no condensation)
100 VAC - 240 VAC ±10%, 50/60 Hz
Power Consumption FA-1010: 80 VA(78 W) (at 100 - 120 VAC)
86VA(72 W) (at 220 - 240 VAC) with FA-10PS: 80 VA (76 W) (at 100 - 120 VAC)
103 VA (73 W )(at 220 - 240 VAC)
Dimensions
Weight
Consumables
Accessories
Options
350 (W) x 400 (D) x 44 (H) mm
7.0 kg (without options)
(Recommended replacement timespans)
Power unit (within 3 years)
Cooling fan: P-1437 (FAN 1 - 4) (within 5 years)
CD-ROM(Windows GUI installation disc (including operation manual)), AC cord, rack mount brackets
◇ FA-10PS: Redundant power supply unit
◇ FA-10ANA-AUD: Analog audio I/O card
◇ FA-10AES-BL: Digital audio balanced output option
◇ FA-10AES-UBL: Digital audio balanced/unbalanced I/O option
◇ FA-10AES-UBLC: Digital audio unbalanced I/O expansion cable
◇ FA-10GPI: GPI Control option
71
7-2. External Dimensions
G EN
D C B
40
DC POWER 1
DC POWER 2
FAN ALARM
GENLOCK
LTC IN
BY-PASS
1
VIDEO
AUDIO
2 3 4
‚r‚c‚h@‚h‚m
5 6 7 8 9 10
INSTALL
OPTION SLOT
A B C
VIDEO IN
AUDIO IN
D
INITIALIZATION
350
430
462
480
A
40
(All dimensions in mm.)
72
Warning
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
2013/09/18 Printed in Japan
FOR-A COMPANY LIMITED
Head Office 3-8-1 Ebisu, Shibuya-ku, Tokyo 150-0013, Japan
Overseas Division Phone: +81(0)3-3446-3936, Fax: +81(0)3-3446-1470
Japan Branch Offices Osaka/Okinawa/Fukuoka/Hiroshima/Nagoya/Sendai/Sapporo
R&D/Production Sakura Center/Sapporo Center
FOR-A America Corporate Office
11155 Knott Ave., Suite G&H, Cypress, CA 90630, USA
Phone: +1-714-894-3311 Fax: +1-714-894-5399
FOR-A America East Coast Office
2 Executive Drive, Suite 670, Fort Lee Executive Park, Fort Lee, NJ 07024, USA
Phone: +1-201-944-1120 Fax : +1-201-944-1132
FOR-A America Distribution & Service Center
2400 N.E. Waldo Road, Gainesville, FL 32609, USA
Phone: +1-352-371-1505 Fax: +1-352-378-5320
FOR-A Corporation of Canada
346A Queen Street West, Toronto, Ontario M5V 2A2, Canada
Phone: +1-416-977-0343 Fax: +1-416-977-0657
FOR-A Latin America & the Caribbean
5200 Blue Lagoon Drive, Suite 760, Miami, FL 33126, USA
Phone: +1-305-931-1700 Fax: +1-305-264-7890
FOR-A Europe S.r.l.
Via Volturno 37, 20861 Brugherio MB, Italy
Phone: +39-039-879-778 Fax:+39-039-878-140
FOR A UK Limited
Trident Court, 1 Oakcroft Road, Chessington, KT9 1BD, United Kingdom
Phone: +44 (0)20-3044-2935 Fax: +44(0)20-3044-2936
FOR-A Italia S.r.l.
Via Volturno 37, 20861 Brugherio MB, Italy
Phone: +39-039-881-086/103 Fax: +39-039-878-140
FOR-A Corporation of Korea
1007, 57-5,Yangsan-ro,Yeongdeungpo-gu, Seoul 150-103, Korea
Phone: +82(0)2-2637-0761 Fax: +82(0)2-2637-0760
FOR-A China Limited
708B Huateng Bldg., No. 302, 3 District, Jinsong, Chaoyang, Beijing 100021, China
Phone: +86(0)10-8721-6023 Fax: +86(0)10-8721-6033
FOR-A Middle East-Africa Office
Jebel Ali Free Zone, LOB-16, Office 619, P. O. Box: 261914 Dubai, UAE
Phone: +971 4 887 6712 Fax: +971 4 887 6713 http://www.for-a.com/
Scarica
Link pubblico aggiornato
Il link pubblico alla tua chat è stato aggiornato. Puoi visualizzare e gestire i tuoi link di chat dopo la registrazione qui.
Link pubblico del documento
Pubblicità
