AC IN 2(option)
Hub
Windows GUI
- Full control
- Quicker response
LAN
Wi-Fi
Web GUI in mobile terminal
- Easy operation
- Partial control
2. Setup Procedure
FA-505
1.
LTC IN/OUT
Time code input and output
LTC IN/OUT
LAN
IN1 OUT1a
SLOT A
A
OUT1b IN2 OUT2a
SLOT B
B
OUT2b IN3 OUT3a
3G /HD/ SD-S DI
Option slots
SLOT C
OUT3b
C
IN4
SDI IN
Cameras, switchers, etc.
3G/HD/SD-SDI input and output connectors.
Alternate Input and output allocation. Bypass outputs signal input (left) to the right of each input/output connector pair (e.g. IN1 > OUT1a).
The procedure is shown numbered in the above figure.
OUT4a
・・・・
OUT4b
Quick Setup Guide
Connection and System Configuration
Monitors, recorders, etc.
1 Apply DC power to the FA-505 using the supplied AC cord. Secure the cord with the supplied AC cord retaining clip.
Ground the unit for your safety.
2 Connect monitors and/or recorders to the SDI OUT connectors.
3 Connect signal source devices such as video cameras and/or switchers, to the SDI IN connectors.
4 Connect a PC to be used for remote control to the FA-505 LAN connector using a LAN cable.
5 Turn the power of the FA-505 on. When the FA-505 is powered on, all LEDs on the front panel, including Alarm indicators light. Once startup is complete, current status will be indicated.
Complete connections before turning the power of the unit on.
GENLOCK IN
External reference signal input
After a setting change, do not turn the unit power off for at least 10 seconds. The setting data may otherwise not save properly.
<Control System Selection>
SLOT D
IN5
D
OUT5a OUT5b
GENL OCK IN
モニター
Packing list
モニター
The FA-505 offers you 2 control systems allowing you to choose in different situations.
Windows GUI
- Enables full control over the FA-505
- Quicker response compare to the Web GUI
Web GUI
- Easy operation on tablet PC or PC
- No space required
SDI OUT
・・・・
FA-505: 1, Quick Setup Guide: 1, CD-ROM: 1 (Windows GUI installation disc including Operation Manuals (PDF)), AC cord: 1, AC cord retaining clip: 1 set,
Rack mount bracket set: 1 set
Option items: FA-10AES-BL, FA-10AES-UBL, FA-10AES-UBLC, FA-50PS,
FA-10GPI, GA-10ANA-AUD, FA-10RU, FA-10DCCRU, FA-AUX30
GENLOCK IN
Loop-through
(Terminate at
75
Ω when not in use.)
AC IN 1
Ground
Terminal
モニター
モニター
2)
Installing the AC Cord Retaining Clip
After connecting the AC cord, secure the AC cord with the supplied ladder strap/retaining clip assembly to prevent accidental removal from the
FA-505.
Be sure to install the AC cord retaining clip before mounting the unit into a rack.
1) Wrap the retaining clip around the AC cord.
(with the anchor of the ladder strap toward the unit.)
2) Insert the anchor into the hole next to the AC
IN socket.
3) Lightly fasten the clip around the AC cord.
4) Plug in the power cord.
5) Slide the clip on the ladder strap toward the plug.
6) Fasten the clip tightly.
7) Gently pull on the AC cord to ensure it is secured.
5)
6)
4)
3)
6 Change the PC network settings for the connection with the
FA-505.
Go to Local Area Connection > General > Internet
Protocol (TCP/IP) > General > Properties, then set the IP address and Subnet mask to match that of the FA-505.
PC IP address
192.168.0.xxx （xxx is any number from 1 to 254 except for the number set for the
FA-505 unit and gateway number.）
Subnet mask Set to 255.255.255.0.
*192.168.0.10 is the default IP address.
<To start up Windows GUI>
7 Install the software, FA-505 GUI.
Open the CD-ROM, and the FA-505GUI folder. Double-click the Setup icon to start the setup wizard.
Once the GUI starts up and a GUI page opens, enter the
FA-505 IP address to register the unit. Click a number under
Select to select a unit, then click Connect to establish a connection with the FA-505.
<To start up Web GUI>
7 Start a web browser on the PC.
Enter the FA-505 IP address into the web browser address bar.
Check your received items against the packing lists. Check to ensure no damage has occurred during shipment. If damage has occurred, or items are missing, inform your supplier immediately.
3. Front Panel Indicators
(1)
DC POWER 1
DC POWER 2
FAN ALARM
(2)
GENLOCK
1 Power switch
2
3
4
Unit status indicator
SDI IN status indicator
LTC IN
OPTION SLOT status indicator
5 INITIALIZATION
BY-PASS
1
VIDEO
AUDIO
SDI IN
2 3 4
(3)
5
INSTALL
OPTION SLOT
A B C
VIDEO IN
AUDIO IN
(4)
D
INITIALIZATION
(5)
Used to turn the unit ON / OFF.
DC POWER 1/2
FAN ALARM
GENLOCK
LTC IN
BY-PASS
VIDEO
AUDIO
INSTALL
VIDEO IN
AUDIO IN
Lit green Power supply is normal.
Lit red
Lit green All fans are operating normally.
Lit red
Lit green Genlock signal input is present.
Unlit
Lit green LTC input is present.
Unlit
Lit green Input signal is being bypassed.
Unlit
Lit green Video signal input is present.
Unlit
Lit green Embedded audio signal is present.
Unlit
Lit green
Unlit
Lit green
Unlit
Lit green
Unlit
A power failure has occurred.
One or more fans have failed.
No genlock signal input is present.
No LTC input is present.
No signal is being bypassed.
No video signal input is present.
No embedded audio signal is present.
One or more option cards are found and recognized in option slots A to D.
No option card is installed or recognized.
Video signal input(s) is/are present in option slot(s).
No video signal input in option slots.
Audio signal input(s) is/are present in option slot(s).
No audio signal input in option slots.
Used to reinitialize the unit. Read the WARNING below before proceding.
To reinitialize the unit, turn the unit on while holding down the
INITIALIZATION button. Continue pressing the button until all LEDs that light together at startup indicate their current status.
All setting data will initialize. Back up before executing a reinitialization.
FA-505
FRAME SYNCHRONIZER
Precautions
Operate the unit only at the specified supply voltage.
Ensure the unit is properly grounded at all times.
Ensure the power cord and connectors are firmly connected.
Do not access circuitry with power applied to the unit.
Unit should not be operated or stored with the cover, panels, and/or casing removed.
Unit should not be operated or stored in a humid, dusty, etc. environment. Doing so could result in fire or electrical shock.
Do not allow fluids, metal fragments, or any other foreign objects to enter the unit. If foreign matter does enter the unit, turn the power off and disconnect the power cord immediately.
Remove the material or contact your authorized service representative
If you notice any strange smells or noises coming from the unit, turn the power off immediately, turn OFF the power switch, disconnect the power cord, then contact your authorized service representative.
