advertisement
DBaseT-Lite HDMI over CAT5e/6/7 with PoE Transmitter -
ID# 15125
Operation Manual
Introduction
Features
HDBaseT-Lite HDMI over CAT5e/6/7 with PoE Transmitter can send uncompressed video and audio over a single run of CAT5e/6/7 cable up to
60 meters (1080p) or 35 meters (4K×2K) with the added benefit of control through the built-in RS-232 and 2-way IR ports. The Power over Ethernet
(PoE) function provides greater flexibility in installations.
•
•
•
•
•
•
•
•
•
HDMI including 3D, 4k×2k supports, HDCP and DVI compliant
Supports HDCP repeater and CEC bypass functions
Supports HDBaseT Technology (Lite version) including 2-Way IR,
RS-232 and Power over Ethernet (PoE)
Supports HD resolutions up to 1080p@60Hz/36-bit and Ultra HD
(4K×2K)
Supports transmission distance of up to 60 meters through
CAT5e/6/7 cable (1080p) or 35 meters (4K×2K)
Supports HDMI input up to 15 meters at 8-bit resolution or 10 meters at 12-bit resolution and output up to 15 meters at 8-bit resolution and 10 meters at 12-bit resolution
RS-232 with baud rate up to 115200/sec
Supports wide range of IR frequency from 30 to 50 kHz
Audio support up to LPCM 7.1CH, Dolby TrueHD, Dolby Digital
Plus and DTS-HD Master Audio
Applications
•
•
•
•
• Household entertainment sharing and control
Lecture room display and control
Showroom display and control
Meeting room presentation and control
Classroom display and control
System Requirements
Input HDMI source equipment such as DVD/Blu-ray players and HDMI equipped output display (TVs or monitors).
Operation Controls and Functions
Transmitter Front and Rear Panel
1. RS-232 In: Connect to a PC/laptop or RS-232 enabled device(with supplied
3.5 mm phone jack to D-Sub 9 pin adaptor) for the transmission of RS-232 commands.
2. IR2 Extender: Connect to the supplied IR extender cable for IR signal reception. Ensure that remote controller being used is within the direct line-ofsight of the IR extender.
3. IR1 Blaster: Connect to the supplied IR blaster cable for IR signal transmission. Place the IR blaster in direct line-of-sight of the equipment to be controlled.
4. HDMI In: Connect to HDMI source equipment such as a DVD or Blu-ray player.
5. DC 24V: Plug the 5 V DC power supply into the unit and connect the adaptor to an AC outlet.
6. Link: The yellow LED will illuminate when both the input and output
CAT5e/6 signals are connected.
7. Power: This green LED will illuminate when the device is connected to a power supply.
8. CAT5e/6 Out: Connect to the receiver unit with a single CAT5e/6 cable for transmission of all data signals..
Receiver Front and Rear Panels
1. RS-232 Out: Connect to the device that is to be controlled (with the supplied 3.5mm phone jack to D-Sub 9-pin adaptor) by RS-232 commands.
2. IR1 Extender: Connect to the supplied IR extender cable for IR signal reception. Ensure that remote being used is within the direct line-of-sight of the IR extender.
3. IR2 Blaster: Connect to the supplied IR blaster cable for IR signal transmission. Place the IR blaster in direct line of sight of the equipment to be controlled.
4.
HDMI Out: Connect to a HDMI equipped TV/monitor for display of the
HDMI input source signal.
5.
Power: This green LED will illuminate when the device is connected to a power supply.
6.
Link: The yellow LED will illuminate when both the input and output
CAT5e/6 signals are connected.
7.
CAT5e/6 In: Connect to the transmitter unit with a Single CAT5e/6 cable for transmission of all data signals
IR Pin Assignment
D-Sub 9-Pin Definitions
Pin
1
2
3
6
7
4
5
8
9
Definitions
N/C
TxD/RxD
RxD/TxD
N/C
GND
N/C
N/C
N/C
N/C
Connection Diagram
Specifications
Video Bandwidth
Transmitter input port
Transmitter output port
Receiver input port
Receiver output port
CAT5e/6/7 distance
HDMI input distance
HDMI output distance
ESD protection
Power Supply
Infrared signal frequency
Size(mm)
Weight
Body Material
Silkscreen color
Operating Temperature
Storage Temperature
Relative Humidity
Power Consumption
300 MHz/10.2 Gbps
1 × HDMI audio and video terminals ,
1 × IR receiver , 1 × RS-232 terminal
(D-sub 9-pin connector )
1 × CAT5e/6/7 terminal , 1 × IR emitter
1 × CAT5e/6/7 terminal , 1 × IR receiver
1 × HDMI audio and video terminals ,
1 × IR emitter ,1 × RS-232 terminal
(D-sub 9-pin connector )
Furthest reach 60 meters
10 m / 8 m , 6 m / 12 m
10 m / 8 m , 6 m / 12 m
Human-body Model:
± 8 kV (air-gap discharge)
± 4 kV (contact discharge)
24 V/1.25 A DC (US / EU standards,
CE / FCC /UL certified)
30 ~ 50 kHz
71(W) × 79(D) × 23(H)
120 g / transmitter , 126 g / Receiver
Aluminum
Black
0 ° C ~ 40 ° C/32 ° F ~ 104 ° F
-20 ° C ~ 60 ° C /-4 ° F ~ 140 ° F
20 ~ 90% RH (non-condensing)
3 W / conveyor , 6 W / Receiver
advertisement
Related manuals
advertisement