advertisement
PU-515PL-KIT
HDBaseT™ LITE Extender Kit with PoE & 2-way IR (up to 60m)
OPERATION MANUAL
DISCLAIMERS
The information in this manual has been carefully checked and is believed to be accurate. CYP (UK) Ltd assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use.
CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be contained in this document. CYP (UK) Ltd also makes no commitment to update or to keep current the information contained in this document.
CYP (UK) Ltd reserves the right to make improvements to this document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer file, in any form or by any means—electronic, mechanical, magnetic, optical, chemical, manual, or otherwise—without express written permission and consent from CYP (UK) Ltd.
© Copyright 2011 by CYP (UK) Ltd.
All Rights Reserved.
Version 1.1 August 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be trademarks of the companies with which they are associated
3
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this equipment:
• Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.
• To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage parts inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufficient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO.
DATE
v1.01
25/10/2013
SUMMARY OF CHANGE
First release
4
CONTENTS
1. Introduction ...........................................6
2. Applications ...........................................6
3. Package Contents ..................................6
4. System Requirements ...........................6
5. Features ..................................................7
6. Operation Controls and Functions .......8
6.1 Transmitter Front and Rear Panels ....... 8
6.2 Receiver Front and Rear Panels ............ 9
6.3 D-Sub 9-Pin Definitions .........................10
6.4 IR Cable Pin Assignment .......................10
7. Connection Diagram .......................... 11
8. Specifications ...................................... 13
9. Acronyms ............................................. 14
5
1. INTRODUCTION
The PU-515PL-KIT allows uncompressed HDMI signals to be transmitted over a Single CAT5e/6/7 cable. This solution has the added features of RS-
232 and 2-way IR control, and Power over Ethernet (PoE) functionality over the same CAT5e/6/7 cable. These combined HDMI and control signals can be transmitted up to lengths of 60 metres.
2. APPLICATIONS
Domestic HDMI installations
University lecturing systems
Retail showroom systems
Conference presentation and control
3. PACKAGE CONTENTS
1×HDMI over Single CAT5e/6/7 Transmitter with PoE
1×HDMI over Single CAT5e/6/7 Receiver with PoE
1×IR Blaster
1×IR Extender
1×3.5 mm Mini-jack to RS-232 Female Cable
1×3.5 mm Mini-jack to RS-232 Male Cable
24 V/1.25 A DC Power Adaptor
Operation Manual
4. SYSTEM REQUIREMENTS
HDMI source equipment such as a DVD or Blu-ray player and HDMI equipped display (TV or monitor). HDMI and CAT5e/5/7 connection cables.
6
5. FEATURES
HDMI 1.4 with 3D, 4K×2K support, HDCP and DVI compliant
Supports HDMI 1.4 (including HDCP) over a single CAT5e/6/7 up to 60m
Complies with HDBaseT™- Lite specifications
Full HD resolution support (1080p@60Hz/36-bit), 3D over 60m, 4Kx2K over
40m and PC resolution support (VGA to WUXGA) over CAT5e/6 cable
HDMI input up to 15m with 8-bit deep colour, or 10m with 12-bit deep colour
Supports HDMI output up to 15m with 8/12-bit deep colour
Supports two-way IR, RS-232 Control, and Power Over Ethernet (PoE)
Installation friendly
Note
1. This system was tested with CAT-6E/23AWG cables, results may vary with cables of a different specification.
2. The PoE function is designed for powering compatible receiver units only—do not use with non-PoE receivers or receivers of another brand.
7
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Transmitter Front and Rear Panels
IR2 Extender
HDMI In
Power
Link
RS-232 In IR1 Blaster
1 2 3
Transmitter
4 5 6 7
CAT 5e /6/7 Out
8
1
RS232 In: Connect to a PC/laptop or RS-232 control device (with supplied 3.5 mm mini-jack to D-sub 9-pin adaptor) for the transmission of RS-232 commands.
2
IR2 Extender: Connect an IR extender cable for IR signal reception.
Ensure that remote control being used is within the direct line-ofsight of the IR extender.
3
IR1 Blaster: Connect an IR blaster cable for IR signal transmission.
Place the IR blaster in direct line-of-sight of the equipment to be controlled.
4
HDMI In: Connect to the HDMI source equipment such as a DVD or
Blu-ray player.
5
DC 24V: Connect the 24V DC power supply to the unit and plug the adaptor into an AC outlet.
6
Link LED: The yellow LED will illuminate when both the input and output CAT5e/6/7 signals are connected. The LED will blink when there is an error with the transmission signal.
7
Power LED: This green LED will illuminate when the device is connected to a power supply.
8
CAT5e/6 Out: Connect to the receiver unit with a single CAT5e/6/7 cable for transmission of all data signals.
8
6.2 Receiver Front and Rear Panels
IR1 Extender
HDMI Out
1 2
Power
Link
CAT 5e /6/7 In
3
RS-232 Out IR2 Blaster
4 5 6 7
Receiver
1
RS232 Out: Connect to the device that is to be controlled (with the supplied 3.5mm mini-jack to D-sub 9-pin adaptor) by RS-232 commands
2
IR1 Extender: Connect an IR extender cable for IR signal reception.
Ensure that the remote being used is within the direct line-of-sight of the IR extender.
3
IR2 Blaster: Connect an IR blaster cable for IR signal transmission.
Place the IR blaster in direct line of sight of the equipment to be controlled.
4
HDMI Out: Connect to a HDMI equipped TV/monitor for display of the
HDMI input source signal.
5
Link LED: This yellow LED will illuminate when both the input and output CAT5e/6/7 signals are connected. The LED will blink when there is an error with the transmission signal.
6
Power LED: This green LED will illuminate when the device is connected to a power supply.
7
CAT5e/6 In: Connect to the transmitter unit with a Single CAT5e/6/7 cable for transmission of all data signals.
9
6.3 D-Sub 9-Pin Definitions
6
7
4
5
PIN
1
2
3
8
9
DEFINE TX/RX
N/C
TxD/RxD
RxD/TxD
N/C
GND
N/C
N/C
N/C
N/C
6.4 IR Cable Pin Assignment
IR Blaster
1
2
3
Power 5 V
IR Blaster Signal
NC
IR Extender
1
2
3
IR Signal
Power 5 V
Ground
10
7. CONNECTION DIAGRAM
Example 1: Direct Connection
3m 3m
60°
IR Extender
DVD or Blu-ray Player
1.5m
60°
IR Blaster
HDMI
Input
Power
Supply
RS-232
Adaptor
IR2 Extender
RS-232 In IR1 Blaster
HDMI In
Transmitter
TX
Power
Link
CAT 5e /6/7 Out
Single
CAT5e/6/7
Cable (60 m)
Power
Link
CAT 5e /6/7 In
IR1 Extender
RS-232 Out IR2 Blaster
HDMI Out
Receiver
RX
Receiver powered over CAT Cable by
PoE
RS-232
Equipped PC or
Notebook
3m
IR Extender
60°
3m
1.5m
IR Blaster
60°
RS-232
Adaptor
HDMI
Output
RS-232 Equipped Device to be controlled
Display
11
Example 2: Using a Repeater to Extend the Operating Distance
Blu-ray Player
RS-232
Equipped PC or Control
System
60°
IR Extender
IR Blaster
1.5m
60°
HDMI
Input
RS-232
Adaptor
RS-232 Device to be Controlled
IR Extender
Power
Supply
IR2 Extender
RS-232 In IR1 Blaster
HDMI In
Transmitter
Power
Link
CAT 5e /6/7 Out
TX
Single
CAT5e/6/7
Cable (60 m)
MODE
CAT5e/6 IN
LINK
POWER
DC 24V
MODE
CAT5e/6 OUT
LINK
Power
Supply
Rear
Front
Optional
HDBaseT Lite
Repeater
Single
CAT5e/6/7
Cable (60 m)
RS-232
Adaptor
Power
Link
CAT 5e /6/7 In
IR1 Extender
RS-232 Out IR2 Blaster
HDMI Out
Receiver
RX
HDMI
Output
60°
1.5m
IR Blaster
3m
60°
3m
HDTV
12
8. SPECIFICATIONS
Video Bandwidth
Transmitter
Input Ports
Output Ports
Receiver
Input Ports
Output Ports
CAT5e/6/7 Cable
Distance
HDMI Input Cable
Distance
HDMI Output Cable
Distance
ESD Protection
300 MHz/10.2 Gbps
1×HDMI, 1×IR Extender, 1×RS-232
1×CAT5e/6/7, 1×IR Blaster
1×CAT5e/6/7, 1×IR Extender
1×HDMI, 1×IR Blaster, 1×RS-232
Up to 60 meters
15 meters/8-bit, 10 meters/12-bit
15 meters/8-bit, 10 meters/12-bit
Power Supply
Human Body Model:
±8 kV (air-gap discharge)
±4 kV (contact discharge)
24 V/1.25 A DC (US/EU standards, CE/
FCC/UL certified)
Dimensions
Weight
Chassis Material
Colour
71 mm (W)×79 mm(D)×23 mm (H)/Each
120 g/TX, 126 g/RX
Metal
Black
Operating Temperature 0 ˚C ~ 40 ˚C / 32 ˚F ~ 104 ˚F
Storage Temperature
−20 ˚C ~ 60 ˚C / −4 ˚F ~ 140 ˚F
Relative Humidity
Power Consumption
20 ~ 90% RH (non-condensing)
3 W/TX, 6 W/RX
13
CAT5e/6/7 Cable Specification:
LENGTH BAND-
WIDTH
DATA
RATE
UP TO
60 M
UP TO
35 M
UP TO
225 MHZ
GREATER
THAN
225 MHZ
UP TO
5.3 GBPS
GREATER
THAN
5.3 GBPS
SUPPORTED VIDEO
HD VIDEO
UP TO 1080P@60 HZ/36-BIT, 3D
(DATA RATE LOWER THAN 5.3
GBPS OR BANDWIDTH BELOW
225 MHZ).
ULTRA HD VIDEO
UP TO 4K×2K@30 HZ.
9. ACRONYMS
ACRONYM
CAT5e
CAT6
CAT7
CEC
DVI
HDCP
HDMI
IR
PoE
COMPLETE TERM
Category 5 Cable
Category 6 Cable
Category 7 Cable
Consumer Electronics Control
Digital Visual Interface
High-bandwidth Digital Content Protection
High-Definition multimedia Interface
Infrared
Power over Ethernet
CYP (UK) Ltd., Unit 7, Shepperton Business Park, Govett Avenue, Shepperton,
Middlesex, TW17 8BA
Tel: +44 (0) 20 3137 9180 | Fax: +44 (0) 20 3137 6279
Email: [email protected]
www.cypeurope.com
v1.01
advertisement
Related manuals
advertisement