Birch DSP880 Series User Manual
The Birch DSP880 Series is a customer pole display with a 20-column by 2-line vacuum fluorescent display, offering a bright blue-green display for clear visibility. It features a unique panel design to complement your retail interior, supports 14 languages, and provides six command modes for versatile use. With its flexible hardware interface options, including USB 2.0 and RS-232C, the DSP880 Series ensures easy integration into your system.
Advertisement
Advertisement
PREFACE
Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Declaration of Conformity
These devices comply with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1.
These devices may not cause harmful interference.
2.
These devices must accept any interference received, including interference that may cause undesired operation.
WEEE (Waste from Electrical and Electronic Equipment)
The WEEE wheeled bin symbol on the product or on its packaging indicates that the product must not be disposed of with other waste. It should be the user’s responsibility to dispose of their waste equipment by handing it over to an approved location for the recycling of waste electrical and electronic equipment.
For more information about where to send your waste equipment for recycling, please contact your local city office, your household waste disposal service or where you purchased the product.
DSP-880 Series Customer Pole Display II
PREFACE
Disclaimer
The material in this document is for information purpose and is subject to change without prior notice. has made every effort to ensure that this user’s manual is accurate and complete. However, no liability is assumed for any errors and omissions that may have occurred. Nor are any liability assumed for any damages resulting from the use of this product and the information contained in this document. reserves the right to make improvements to this publication from time to time in the contents hereof without obligation of the manufacturer to notify any person of such revision or changes.
Copyright
This work is copyrighted. Reproduction or retransmission of this documentation, in whole or in part, without prior written permission from the manufacture is a violation of copyright law.
© 2016 Technology Co., Ltd. All rights reserved.
Trademark Recognition
Microsoft, Windows are registered trademarks of Microsoft Corp.
Intel is a registered trademark of Intel International Inc.
Other software or product names used in this manual are the properties of their respective owners and are acknowledged.
III DSP-880 Series Customer Pole Display
PREFACE
Important Safety Instructions
Failure to observe these safety instructions may cause bodily injury, or damage to the product. Read these instructions carefully and keep this user’s manual in an accessible location for future reference.
The product may cause a fire or electric shock when it is used improperly. Observe the above safety measures at all times.
If the product is damaged, immediately turn off the power and disconnect the power cord. Contact your dealer for assistance.
1. Do not plug in or unplug the power cord with wet hands.
2. Do not plug the product into an AC outlet with the incorrect voltage.
(Be sure to use a voltage that is between AC 100V~240V)
3. Do not plug several products into one multi-outlet.
4. Do not apply pressure to the power cord or place heavy objects on it.
5. Immediately stop using the product if it emits strange noise, odor, or smoke.
6. Do not use aerosol sprayers containing flammable gas inside or around the product.
7. Do not allow foreign objects or liquids to enter the product, or serious damage may result.
8. Do not place the product on an unstable surface. The product may cause a fire if it is dropped, damaged, or broken.
The following instructions will help you to make better use of this product.
1. Keep the machine away from locations subject to high humidity, dust, or temperatures that exceed the specification.
2. Clean the product only by using a dry cloth or a cloth soaked with detergent. Never use thinner or other volatile solvents for cleaning.
3. At the end of the day, clean and inspect the exterior of the machine after the machine is powered off.
4. Use only specified accessories.
5. Do not expose the accessories directly to sunlight, high temperatures, humidity, dust, or gas.
6. Do not place heavy objects on top of the product or lean them against the product. These items may fall down and cause injury.
Do not block the air vent of the product as this can cause heat accumulation inside the box machine and may cause a fire.
DSP-880 Series Customer Pole Display IV
Table Of Contents
CHAPTER 1 INTRODUCTION ............................................... 2
1.1
Unpacking ........................................................................... 2
1.2
1.3
Features .............................................................................. 3
Specification ........................................................................ 4
CHAPTER 2 INTERFACE....................................................... 5
2.1 Connection to Display Panel ................................................... 5
2.2 DSP-880 ..
................
............................................................ 5
2.3 DSP-880 USB .
...
......
........................................................... 6
2.4 DSP-880 RS232 ....................
.......
........................................ 6
CHAPTER 3 INSTALLATION................................................. 8
3.1 Physical Function .................................................................. 8
3.2 Configuration ..................................................................... 10
3.3 Driver Installation ............................................................... 13
CHAPTER 4 CONFIGURE YOUR DEVICE ............................. 14
4.1 Before starting ................................................................... 14
4.2 Configure System Parameters .............................................. 16
4.3 Define Welcome Message .................................................... 18
4.4 Define Your Own Font ......................................................... 20
CHAPTER 5 SOFTWARE SETTING COMMAND ..................... 22
5.1 Baud Rate Setting Command ............................................... 22
5.2 Parity Check Setting Command ............................................ 22
5.3 USB Class Setting Command ................................................ 22
5.4 Command Type Setting Command ........................................ 23
5.5 International Character Set Setting Command ........................ 23
CHAPTER 6 COMMAND SET ............................................... 24
6.1 ESC/POS Mode Command Set .............................................. 24
6.2 ADM787/788 Mode Command Set ........................................ 26
6.3 EMAX (AEDEX) Mode Command Set ...................................... 27
INTRODUCTION
6.4 UTC Mode Command Set ..................................................... 27
6.5 CD5220 Mode Command Set................................................ 28
6.6 DSP-800 Mode Command Set .............................................. 31
CHAPTER 7 CHARACTER SET............................................... 32
7.1 Character Code (20h-7Eh) ................................................... 32
7.2 Character Code Page (80h-FFh) ............................................ 33
1 DSP-880 Series Customer Pole Display
INTRODUCTION
CHAPTER 1 INTRODUCTION
Welcome
Thank you for choosing the DSP-880 Series Customer Pole Display.
The DSP-880 Series is a 20 columns x 2 lines customer Vacuum
Fluorescent Display panel. VFD emits a very bright light with high
Based on VFD display method, the DSP-880 Series gives a better view of message in bright blue-green display fonts.
1.1 Unpacking
Confirm that all the following items are contained in the carton. If any item is missing or damaged, contact the dealer from whom you purchased the product.
DSP-880 Series Customer Pole Display Set:
Display Panel
Accessory Kit:
Pole: 120 mm x 2 Stand Base
Quick Reference Guide
Driver CD
(User’s Manual included)
Dual Interface Cable
(For
DSP-880
)
RS232 Cable
(For DSP-880 )
DSP-880 Series Customer Pole Display
USB Cable
(For DSP-880 )
2
INTRODUCTION
1.2 Features
1. Vacuum Fluorescent Display
2. Eye-catching bright blue-green display font
3. Unique panel design to vitalize your retail interior.
4. Supports 14 language characters, including those from the USA, France,
Germany, UK, Sweden, Denmark I and II, Italy, Spain, Norway, Greek,
Slavonic, Russian and Portuguese.
5. Provides 6 command modes: EPSON ESC/POS, ADM787/788, UTC/S, UTC/P,
EMAX (AEDEX), CD5220 and DSP-800.
6. The wide-range of power supplies input to prevent misuse.
7. Low power consumption achieves optimal energy use and reliability.
8. Innovative hinge design for quick panel adjustment.
9. User-programmable for all fonts and customer messages.
10. Hardware Interface:
Standard
Full speed data transfer using the USB 2.0 protocol.
RS-232C Interface with baud rates selectable from 9600 to 115200 bps.
11. Mechanical:
Provides a wide range of rotation and tilt angles.
Selectable pole length for best position installation.
3 DSP-880 Series Customer Pole Display
INTRODUCTION
1.3 Specification
Model
Display Method
Number of Characters
Display Color
Brightness
Font
Character Size
Command Set
Interface
Power Supply
Power Consumption
MTBF
Physical Dimension
Head (W x D x H)
Support (H x Ø)
Base (W x D x H)
Weight
Environment
EMC & Safety
Operation Temperature
Storage Temperature
Operation Humidity
Storage Humidity
Mechanical
Housing Color
DSP-880 Series
Vacuum Fluorescent Display (VFD)
40 characters (20 columns x 2 lines)
Blue-green
700 cd/m2
I.
96 alphanumeric
II. 14 sets of international characters: USA,
France, Germany, UK, Sweden, Denmark I and
II, Italy, Spain, Norway, Japan (Katakana),
Slavonic, Russian and Portuguese
III. One set of user downloadable characters
5x7 Dot Matrix
9.03 mm x 5.25 mm
1. EPSON ESC/POS
2. ADM787/788
3. EMAX (AEDEX)
4. UTC/S, UTC/P
5. CD5220
6. DSP-800
Dual Interface (USB+RS232C) / USB / RS232C
DC 5V (via USB or DB9)
<3W
30,000 hrs
225.5 x 50 x 87 mm
(120 x 35 mm) X 2
187 x 92 x 27 mm
N.W. 0.8kg
CE/FCC Class A
5~45
℃
-20~70 ℃
15%~80% RH
10%~90% RH
Black
DSP-880 Series Customer Pole Display 4
INTERFACE
CHAPTER 2 INTERFACE
2.1 Connection to Display Panel
All the DSP-880 Series has RJ-45 connector to display end. Connector
Type: 10 Pin Phone Jack Pin assignment
Pin No. Signal
6
7
8
9
10
1
2
3
4
5
GND
USB
USB
USB
TXD
DSR
RXD
DTR
VIN
GND
I/O Function
- Ground
Data -
Data +
VBUS
Output Transmit Data
Output Data Set Ready
Input Receive Data
Input Data Terminal Ready
Input +5V
- Ground
Illustration
2.2
DSP-880
RS232C Type
Data transmission
Synchronization
Handshaking
Asynchronous
None
Serial
Signal level
MARK = -3 to -15V (logical “1” OFF)
SPACE = +3 to +15V (logical “0” ON)
Baud rate
Parity
9600, 19200, 38400, 115200 bps
None, Even
Bit length (Data word
Stop bits
8 bits
1 bit
USB Type
The DSP-880 Series is compatible to the High-speed USB 2.0 protocol which has a raw data rate of 12 megabits per second (Mbps).
5 DSP-880 Series Customer Pole Display
INTERFACE
2.3
DSP-880 USB
Connector Type: USB 2.0 B Type
Pin assignment
Pin No.
Pin 1
Pin 2
Pin 3
Pin 4
Signal
VCC
Data –
Data +
GND
Illustration
Type A
2.4
DSP-880 RS232
Connector Type: D-sub 9Pin (Female)
Pin assignment
Pin No. Signal
2 TXD
3
4, 7
RXD
I/O Function
Output Transmit Data
Input Receive Data
DTR/RTS Output Data Terminal Ready
5
6,8
GND - Ground
DSR/CTS Input Data Set Ready
Illustration
1
6 9
5
NOTE: PIN9 DC input is necessarily required when DB9 functions as power source.
DSP-880 Series Customer Pole Display 6
NSTALLATION
CHAPTER 3 INSTALLATION
The DSP-880 Series Customer Pole Display is easy to install by following the instructions in this chapter. No special training or tools are necessary. As this manual contains required information on the installation and programming of DSP-880 Series Customer Pole Display, it is recommended that you read the entire manual carefully prior to initiating installations.
3.1 Physical Function
225.5
87.1
3.1.2 Assembling
Insert the RJ45 end of the dual interface cable through the base and the pipe then into the panel and connect to the RJ45 slot. You can extend the pole to the desired height by attaching the extension pole for different heights:
Low 200 (mm), Mid 323.7 (mm) and Highest
443.7 (mm).
NOTE: Attach the joint of the extension pole or stand base to the Display Panel until it is properly locked.
DSP-880 Series Customer Pole Display 8
INSTALLATION
ATTENTION
(1) Violently rotating the Display Panel may cause damages of the Display Panel.
(2) Secure the Display Panel properly after attaching the extension pole to a desired height.
3.1.4 Angling
This product allows 0~28 degree tilt angle adjustment. The Display Panel can be easily tilted to the desired position by using a hinge design.
How to Adjust
(1) Locate the hinge section on the backside of Display Panel.
(2) Pull the tab downward and tilt the panel up or down to the desired position.
28°
9 DSP-880 Series Customer Pole Display
NSTALLATION
3.2 Configuration
3.2.1 Dual Interface Cable Connection
Step 1 Turn OFF the system power
Before you start the installation, ensure that the host computer and the
DSP-880 Series Customer Pole Display are powered off.
Step 2 Connect all the dual Interface cable
Step 3 Start the host PC and switch on the display.
Host/PC Display
RS232 Male
USB A Type
RS232 DB9
Female
USB 5V
ATTENTION
With the dual interface cable, the DSP-880 Series is able to be powered only by the
USB 5V.
DSP-880 Series Customer Pole Display 10
INSTALLATION
3.2.2 USB Connection
Step 1 Turn OFF the system power
Before you start the installation, ensure that the host computer and the
DSP-880 Series Customer Pole Display are powered off.
Step 2 Connect the USB cable
Step 3 Start the host PC and switch on the display.
Host/PC Display
USB A Type
USB 5V
ATTENTION
With the dual interface cable, the DSP-880 Series is able to be powered only by the
USB 5V.
11 DSP-880 Series Customer Pole Display
NSTALLATION
3.2.3 RS232 Connection
Step 1 Turn OFF the system power
Before you start the installation, ensure that the host computer and the
DSP-880 Series Customer Pole Display are powered off.
Step 2 Connect the RS232 cable
Plug the DB9 Female connector of RS232 cable and make sure the 9th pin of the com port on the PC is powered by 5V.
Step 3 Start the host PC and switch on the display.
Host/PC Display
RS232 Male
RS232 DB9
Female
DSP-880 Series Customer Pole Display 12
3.3 Driver Installation
The firmware for the USB port is divided into CDC class (Virtual COM) and printer class. To recognize which firmware version it is, check the starting status of your customer display as Pic 1a,Pic
1b,Pic1c.
Pic 1a
Pic 1b
In case your USB port is in CDC class and your application software is connected by
USB port, you must install the driver:
Pic 1c
-Click CDC Class as Pic 2.
-check the device manager to find the
COM port number as below.
Pic 2
If your Application Software needs to install the printer mode driver:
Click Printer Class as Pic 3 and select:
-Serial/Virtual for COM Connection.
-USB for USB Connection.
Pic 3
INSTALLATION
13 DSP-880 Series Customer Pole Display
NSTALLATION
CHAPTER 4 CONFIGURE YOUR DEVICE
The system parameters of DSP-880 Series can be set by using VFD Utility software tool. You can find the tool in the companion disk. In addition to setting system parameters, you can configure welcome message and user font with the software tool. The system parameters include the following items.
Language Character Set
Command Type
Baud rate
Parity Check
4.1 Before starting
Before starting the software, please make sure the DSP-880 Series is connected to your PC and it works. If you use USB interface or device driver, please install device driver before starting the software. If the connection is OK, execute the software.
4.1.1 Select a proper interface
After starting the software, the following dialog will pop up. Select a proper interface.
DSP-880 Series Customer Pole Display 14
INSTALLATION
4.1.2 RS-232 Interface
If you select the item COM port (RS232 only), the dialog of RS-232 setting will show up to configure the RS-232 interface. Please make sure the parameters that you type here are the same as the settings of your host PC. If the parameters aren’t the same, the communication between host PC and your machine will fail.
4.1.3 Selecting Device Driver
Please select your device from the pull-down list on following dialog. If the device driver is installed, your device shall be shown on the list.
4.1.4 Select Model Name
Before continue, please select a proper model name that matches with your device’s model. The model name can be selected on the upper-right corner of the window. If the model name does not match with your device, the configuration may not take effect.
15 DSP-880 Series Customer Pole Display
NSTALLATION
4.2 Configure System Parameters
There are three pages on the main dialog. The first one is the Configuration Page.
You can select desired character type, command set and baud rate of RS-232 interface. After all items are set to desired condition, press SET button to send all the settings to your device. These settings will be stored on the non-volatile memory. Every time when you start the device, these settings will be retrieved from non-volatile memory.
DSP-880 Series Customer Pole Display 16
INSTALLATION
4.2.1 Command Type
The DSP-880 Series supports up to 8 command sets. They are listed on the following table. Please select one from the pull-down list.
Command Type
EPSON ESC/POS
Default
*
DSP-800
ADM787/788
EMAX(AEDEX)
UTC/S
UTC/P
CD5220
Reserved
4.2.2 Language Character Set Selection
The DSP-880 Series supports the following language character set. Please refer to following table for character code page.
Character Set(20h-7Fh) Code Table (80H-FFH)
PC-437 (USA, Standard Europe) U.S.A
France
Germany
U.K.
Denmark I
Sweden
Italy
Spain
Reserved
Norway
Denmark II
U.S.A
U.S.A
U.S.A
U.K.
U.S.A
U.S.A
U.S.A
U.S.A
U.S.A
U.S.A
U.S.A
Japan
User Font
PC-858
PC-858
Slavonic
Russia
PC-860 (Portuguese)
Greek
PC850
PC852
PC863
PC865
WPC1252
WPC1255
WPC1257
Katakana
Default
*
17 DSP-880 Series Customer Pole Display
NSTALLATION
4.2.3 Baud Rate Selection
Baud Rate (bps)
9600
19200
38400
115200
Default
*
4.2.4 Parity Check Selection
Parity Check
None-parity
Even-parity
Default
*
4.2.5 USB Class Selection
USB Class
Printer class
CDC class
Default
*
DSP-880 Series Customer Pole Display 18
INSTALLATION
4.3 Define Welcome Message
You can define your own message in the display. The Msg1 will blink on upper line while the Msg2 is displayed on lower line in marquee status.
You can type the character on keyboard in ASCII mode or type others in Hex mode. Press Set button to send the messages to the machine.
19 DSP-880 Series Customer Pole Display
NSTALLATION
4.4 Define Your Own Font
You can create your own font and download it with the software tool.
There are three ways to create the font:
4.4.1 From an Existing Font
You can see the following dialog by pressing “Open Exist Font” button.
Please select a font to be your font base and modify it to fit your requirement.
1, The first part is ASCII code which contains the characters coded as 0x20~0x7f.
Within the ASCII, some of characters own different definition in different country.
Please refer to the user’s manual for the details of the code table.
2, The second part is 0x80~0xff which is the range that code page refer to. You can select a desired code page from the list as a base of your font.
After selecting these existing font, press “Load Existing Font” and the font will be loaded into system memory. Once you finish editing font, you can choose either to save your font to a file by pressing “Save to file” or download your font to device by pressing “Download to device”. If you want to quit current modification, you can press “Reload font” button to load the font again. All your modification will be lost after reloading font. Press “Reset” button also let you abandon current modification and restart the whole operation.
DSP-880 Series Customer Pole Display 20
INSTALLATION
4.4.2 From Your Font File
You can modify previously edited and saved font file. Press “Open Font File” button the following dialog will be shown. After select a file, the font contained in that file will be loaded into memory. Then, you can edit font, save font to a file or download the font to device.
4.4.3 From your scratch
If you want to build your font from scratch, press “Create New File” button to create an empty font. After finishing your edit, you can save font to a file or download the font to device. It is a difficult job to build font from zero. It is recommended to build your font from existing font.
21 DSP-880 Series Customer Pole Display
SOFTWARE SETTING COMMAND
CHAPTER 5 SOFTWARE SETTING COMMAND
User can re-set the default configuration by using the following software commands:
5.1 Baud Rate Setting Command
STX 05 B n ETX Change the baud rate
ASCII Format
Dec. Format
STX 05 B n ETX STX 05 E N ETX
[02][05][66] n [03] [02] [05] [49] [78] [03] 49 ≦n≦51
Hex. Format
Description
[02h][05h][42h] n [03h][02h][05h][45h][4eh][03h] 31h ≦ n ≦ 33h
Change the display communication baud rate. The baud rate setting can be selected from 9600~115200 bps.
N
30h
31h
32h
33h
Baud rate
115200
38400
19200
9600
5.2 Parity Check Setting Command
STX 05 P n ETX Change the parity check
ASCII Format
Dec. Format
STX 05 P n ETX STX 05 E N ETX
[02][05][80] n [03] [02] [05] [69] [78] [03] n=48,49
Hex. Format
Description
[02h][05h][50h] n [03h][02h][05h][45h][4eh][03h] n=30h,31h n
30h
31h
Parity check
None parity
Even parity
5.3 USB Class Setting Command
STX 05 U n ETX Change the USB class
ASCII Format
STX 05 U n ETX STX 05 E N ETX
Dec. Format
Hex. Format
Description
[02][05][85] n [03] [02] [05] [69] [78] [03] n=48,49
[02h][05h][55h] n [03h][02h][05h][45h][4eh][03h] n=30h,31h n
30h
31h
USB class
Printer class
CDC class
DSP-880 Series Customer Pole Display 22
n
30h
31h
32h
33h
34h
35h
36h
37h
38h
39h
3Ah
3Bh
3Ch
3Dh
3Eh
3Fh
23
INSTALLATION
5.4 Command Type Setting Command
STX 05 C n ETX
ASCII Format
Dec. Format
Hex. Format
Description
Change the command type
STX 05 C n ETX STX 05 E N ETX
[02][05][67] n [03] [02] [05] [69] [78] [03] n=49,51,55
[02h][05h][43h] n [03h][02h][05h][45h][4eh][03h] n=31h,33h,37h
Change the command type and initialize the display n
31h
32h
33h
34h
Command type n
ESC/POS 35h
ADM787/788 (option) 36h
DSP-800 (option) 37h
EMAX (AEDEX)
Command type
UTC/P
UTC/S
CD5220
5.5 International Character Set Setting Command
STX 05 S n ETX
ASCII Format
Dec. Format
Hex. Format
Description
Change the International character set
STX 05 S n ETX STX 05 E N ETX
[02][05][83] n [03] [02] [05] [69] [78] [03] 48 ≦ n ≦ 63
[02h][05h][53h] n [03h] [02h][05h][45h][4eh][03h]
30h ≦ n ≦ 3Fh
Change the display International character set
Character Set
(20h–7Fh)
U.S.A.
France
Germany
U.K.
Denmark I
Sweden
Italy
Spain
Reserved
Norway
Denmark II
U.S.A.
U.S.A.
U.S.A.
U.K.
User Font
Code Table (80H-FFH)
PC-437 (USA, Standard Europe)
PC-858
PC-858
Slavonic
Russia
PC-860 (Portuguese)
Greek
DSP-880 Series Customer Pole Display
COMMAND SET
CHAPTER 6 COMMAND SET
6.1 ESC/POS Mode Command Set
Command
HT
BS
US LF
LF
US CR
CR
HOM
US B
US $ x y
CAN
CLR
US X n
US E n
ESC @
ESC # n
ESC R n
ESC t n
US r n
US # n m
US C n
US MD1
US MD2
US MD3
US @
US . n
Code (hex)
09
08
1F 0A
0A
1F 0D
0D
0B
1F 42
1F 24 x y
01h ≦ x ≦ 14h, y=01h, 02h
18
0C
1F 58 n
01h
≦ n
≦
04h (=brightest)
1F 45 n
00h
≦ n
≦
FFh
1B 40
1B 23 n
30h
≦ n
≦
38h
1B 52 n
00h
≦ n
≦
0Ch
1B 74 n n=00h, 01h..07h, 10h,
13h,0Ah~0Dh
1F 72 n n=00h, 01h
1F 23 n m n=00h, 01h, 01h<m
≦
14h
1F 43 n n=00h, 01h
1F 01
1F 02
1F 03
1F 40
1F 2E n
Function description
Move cursor right.
Move cursor left.
Move cursor up.
Move cursor down.
Move cursor to right-most position.
Move cursor to left-most position.
Move cursor to home position.
Move cursor to bottom position.
Move cursor to specified position.
Clear cursor line.
Clear display screen.
Brightness adjustment.
Blink display screen.
Initialize display.
Command type select
Select international character set.
(see Table 5-A)
Select character code table.
(see Table 5-B)
Select/Cancel reverse character. n=01 select, n=00 cancel
Turn annunciator on/off n=01 on, n=00 off
Set cursor on/off n=01 on, n=00 off
Specify overwrite mode.
Specify vertical scroll mode.
Specify horizontal scroll mode.
Execute self-test.
Specify period
DSP-880 Series Customer Pole Display 24
COMMAND SET
US , n
US ; n
ESC & s n m
[a(p1..pa)]x m-n+1
ESC ? n
ESC % n
ESC W n s x1 y1 x2 y2 n=a displayable character code
1F 2C n n=a displayable character code
1F 3B n n=a displayable character code
1B 26 1 n m
[a(p1..pa)]x m-n+1
21h
≦ n
≦ m
≦
FFh; 1
≦ a
≦
5 p1..p5=row1...row5
1B 3F n
21h ≦ n ≦ FFh
1B 25 n n=00h, 01h
1B 57 n s x1 y1 x2 y2
1 ≦ n ≦ 4, s=00h,01h
01h
≦ x1
≦ x2
≦
14h
01h
≦ y1
≦ y2
≦
02h
ESC = n 1B 3D n n=01h, 02h, 03h
US :
US ^ n m
US T h m
US U
US V n
1F 3A
1F 5E n m
00h
≦ n
≦
FFh
00h
≦ m
≦
FFh
1F 54 h m
00h
≦ h
≦
17h
00h
≦ m
≦
3bh
1F 55
1F 56 n
00h
≦ n
≦
01h
Specify comma
Specify semicolon
(period + comma)
Define download characters.
Delete download characters.
Select/cancel download character set. n=01 select, n=00 cancel
Specify/cancel the window range. s=01 specify, 00 cancel n=select the window x= column position y= row position
Select peripheral device. n=01h, select printer n=02h, select display n=03h, select printer + display
Set starting/ending position of macro definition.
Execute and quit macro. n=word time m=show string time
Display time
Display time continuously
Status confirmation by DTR signal
25 DSP-880 Series Customer Pole Display
COMMAND SET
09
0A
0B
0C
05
06
07
08 n
00
01
02
03
04
International Font
U.S.A.
France
Germany
U.K.
Denmark I
Sweden
Italy
Spain
Japan
Norway
Denmark II
Slavonic
Russia
Table 5-A Select International font n Code Table (80H-FFH)
00 Page 0, (PC437, USA standard Euro)
01 Page 1, (Green)
02 Page 2, (PC850, Multilingual)
03 Page 3, (PC860, Portuguese)
04 Page 4, (PC863, Canadian-French)
05 Page 5, (PC865, Nordic)
06 Page 6, (Slavonic)
07 Page 7, (Russian)
13h Page 19, (PC858, +Euro symbol)
10h Page 16, (WPC1252)
0A Page 10,(Katakana)
0B Page 11,(PC852)
0C Page 12,(WPC1255)
0D Page 13,(WPC1257)
Table 5-B Select code table
6.2 ADM787/788 Mode Command Set
Command
CLR
CR
SLE1
SLE2
DC0
DC1
DC2
SF1
0C
Code (hex)
0D
0E
0F
10 n
31H
≦ n
≦
37H
11 n n=31h, 32h
12 n n=31h, 32h
1E
Function Description
Clear display
Carriage return
Clear filed 1 (upper-left line) and move cursor to the first position
Clear filed 2 (bottom-left line) and move cursor to the first position
Set the period to the upper line last n position
Set line blinking, n=31h upper line; n=32h bottom line
Clear line blinking, n=31h upper line; n=32h bottom line
Clear field 3 (upper-right line) and move cursor to the first position
DSP-880 Series Customer Pole Display 26
SF2 1F
COMMAND SET
Clear field 4 (bottom-right line) and move cursor to the first position
6.3 EMAX (AEDEX) Mode Command Set
Command Function Description
! # 1 … CR
! # 2 … CR
! # 4 … CR
! # 5 … CR
! # 6 … CR
! # 8 … CR
! # 9 … CR
Code (hex)
21 23 31 [d1, d2...dn] 0D
1
≦ n
≦
20
21 23 32 [d1, d2...dn] 0D
1
≦ n
≦
20
21 23 34 [d1, d2...dn] 0D
1
≦ n
≦
40
21 23 35 h1h2 “:” m1m2 0D
“:”=3A
30h ≦ h1 ≦ 32h; 30h ≦ m1 ≦ 35h
30h ≦ h2, m2 ≦ 39h
21 23 36 [d1, d2...dn] 0D
1 ≦ n ≦ 64
21 23 38 n m 0D
20h
≦ n, m
21 23 39 [d1, d2...dn] 0D
1
≦ n
≦
40
Upper line display
Bottom line display
Upper line message scroll continuously
Display time h=hour m=minute
Upper line message scroll once pass
Change attention code
Two line display
6.4 UTC Mode Command Set
UTC/S (STANDARD)
Command
BS
HT
LF
CR
DLE
DC1
DC2
DC3
DC4
US
ESC d
Code (hex)
11
12
13
14
08
09
0A
0D
10 n
00h ≦ n ≦ 27h
1F
1B 64
Function Description
Back space
Horizontal tab
Line feed
Carriage return
Display cursor position
Over write display mode
Vertical scroll mode
Cursor on
Cursor off
Clear display
Change to UTC enhanced mode
27 DSP-880 Series Customer Pole Display
COMMAND SET
UTC/P (ENHANCED)
Command Code (hex)
ESC u A ....CR 1B 75 41 [d1, d2...dn] 0D
1 ≦ n ≦ 20
ESC u E ….CR 1B 75 45 h1h2 “:” m1m2 0D
“:”=3A
30h ≦ h1 ≦ 32h; 30h ≦ m1 ≦ 35h
30h ≦ h2 ≦ 34h, 30h ≦ m2 ≦ 39h
ESC u H ….CR 1B 75 48 n m 0D
20h ≦ n, m
ESC u I ….CR
1B 75 49 [d1, d2...dn] 0D
1 ≦ n ≦ 40
ESC RS ….CR 1B 0F 0D
Function Description
Upper line display
Bottom line display
Upper line message scroll continuously
Display time hh= hour mm= minute
Upper line message scroll once pass
Change attention code
Two line display
Change to UTC standard mode
6.5 CD5220 Mode Command Set
Command Code (hex)
ESC DC1
US SOH
1B 11
1F 01
ESC DC2
US STX
1B 12
1F 02
1B 13 ESC DC3
US ETX 1F 03
ESC QA ....CR 1B 51 41 [d1, d2...dn] 0D
1 ≦ n ≦ 20
ESC QB ....CR 1B 51 42 [d1, d2…dn] 0D
1 ≦ n ≦ 20
ESC QD ....CR 1B 51 44 [d1, d2…dn]xm 0D m
≦
40
ESC [ D 1B 5B 44
BS
ESC [ C
HT
08
1B 5B 43
09
Function description
Overwrite mode
Overwrite mode
Vertical scroll mode
Vertical scroll mode
Horizontal scroll mode
Horizontal scroll mode
Set the string display mode, write string to upper line
(see Note 1)
Set the string display mode, write string to bottom line
(see Note 1)
Upper line message scroll continuously (see Note 2)
Move cursor left
Move cursor left
Move cursor right
Move cursor right
DSP-880 Series Customer Pole Display 28
ESC [ A
US LF
ESC [ B
LF
ESC [ H
HOM
ESC [ L
CR
ESC [ R
US CR
1B 5B 41
1F 0A
1B 5B 42
0A
1B 5B 48
0B
1B 5B 4C
0D
1B 5B 52
1F 0D
Move cursor up
Move cursor up
COMMAND SET
Move cursor down
Move cursor down
Move cursor to home position
Move cursor to home position
Move cursor to top-left position
Move cursor to top-left position
Move cursor to top-right position
Move cursor to top-right position
Move cursor to bottom position
Move cursor to bottom position
Command type select
ESC [ K
US B
ESC # n
US @
US E n
ESC l x y
US $ x y
ESC @
CLR
CAN
ESC * n
US X n
ESC & s n m
[a(p1..pa)]x
(m-n+1)
1B 5B 4B
1F 42
1B 23 n n=31h~37h
1F 40
1F 45 n n=00h~FFh
1B 6C x y
1 ≦ x ≦ 14h y=01h, 02h
1F 24 x y
01h ≦ x
1B 40
≦ 14h; y=01h, 02h
ESC W s x1 x2 y 1B 57 s x1 x2 y
01h ≦ x1 ≦ x2 ≦ 13h y=01h, 02h, s=00h, 01h
0C
18
1B 2A n
01h ≦ n ≦ 04h (=brightest)
1F 58 n
01h
≦ n
≦
04h (=brightest)
1B 26 1 n m
[a (p1..pa)] x (m-n+1)
20h ≦ n ≦ m ≦ FFh
1 ≦ a ≦ 5 p1...p5=row1...row5
Execute self test
Blink display screen n=00h for no blink
Move cursor to specified position x= column position y= row position
Move cursor to specified position
Initialize display
Set/Cancel the window range at horizontal scroll mode x= column position y= row position
Clear display screen and clear string mode
Clear cursor line and clear string mode
Brightness adjustment
Brightness adjustment
Define download characters
29 DSP-880 Series Customer Pole Display
COMMAND SET
ESC ? n
ESC % n
ESC _ n
ESC f n
ESC c n
ESC = n
ESC s 1
ESC d 1
1B 3F
1B 25 n n=00h, 01h
1B 5F n n=00h, 01h
1B 66 n
1B 63 n
1B 3D n n=01, 02h, 03h
1B 73 01
1B 64 01
Delete download characters
Select/Cancel download character set n=01 select, n=00 cancel
Set cursor on/off n=01 cursor on, n=00 cursor off
Select international font set
(see Note 3)
Select code (see Note 4)
Select peripheral device n=01h, select printer n=02h, select display n=03h, select printer + display
Store the user defined character into EEPROM.
Download the user defined character from EEPROM.
NOTE:
1. While using the command “ESC Q A” or “ESC Q B”, other commands cannot be used except for “CLR” or “CAN” to change the operating mode.
2. When using the command “ESC Q D”, the upper line message will scroll continuously until a new command is received. It will then clear the upper line and move the cursor to the upper left end position.
3. The parameters of the international font set control command “ESC f n”.
Parameter “n”
‘S’
‘N’
‘W’
‘D’
‘E’
‘L’
‘R’
‘A’
‘G’
’I’
‘J’
‘U’
‘F’
53h
4Eh
57h
44h
45h
4Ch
52h
41h
47h
49h
4Ah
55h
46h
International Font Set
U.S.A.
Germany
Italy
Japan
U.K.
France
Spain
Norway
Sweden
Denmark I
Denmark II
Slavonic
Russia
4. The parameters of the code table control command “ESC c n”.
Parameter “n”
‘A’
‘L’
‘R’
41h
4Ch
52h
DSP-880 Series Customer Pole Display
International Font Set
Compliance with ASCII code
Compliance with SLOVONIC code
Compliance with RUSSIA code
30
COMMAND SET
6.6 DSP-800 Mode Command Set
Command Code (hex) Function Description
EOT SOH I n ETB
EOT SOH P n ETB
04 01 49 n 17 n=00~0Fh or 30~3Fh
04 01 50 n 17
31h ≦ n ≦ 58h
EOT SOH C n m ETB 04 01 43 n m 17
31h ≦ n ≦ m ≦ 58h
Select International character set
(see Table 5-C)
Move cursor to specified position
Clear display range from n to m position and move cursor to n position
Save the current view data to n layer for demo display
Display the saved demo message
(see Table 5-D)
EOT SOH S n ETB 04 01 53 n 17
31h ≦ n ≦ 35h
EOT SOH D n m ETB 04 01 44 n m 17
31h ≦ n ≦ 4Fh
31h ≦ m ≦ 33h
EOT SOH A n ETB
EOT SOH F n ETB
EOT SOH & n [px5]
ETB
EOT SOH ? n ETB
EOT SOH = n ETB
04 01 41 n 17
31h ≦ n ≦ 34h
04 01 46 n 17
00h ≦ n ≦ FFh
04 01 26 n p1…p5 17
20h ≦ n ≦ FFh
1 5 1 5
20h ≦ n ≦ FFh
04 01 3D n 17 n=31h, 32h, 33h
Brightness adjustment
Blink display screen n=00h for no blink
Define download characters
Delete download characters
Select peripheral device. n=31h, select printer n=32h, select display n=33h, select printer + display
EOT SOH % ETB
EOT SOH @ ETB
EOT SOH # n ETB
04 01 25 17
04 01 40 17
04 01 23 n 17
Initialize display
Execute self-test
Command type select n
30h
31h
32h
33h
34h
35h
36h
37h
38h
39h
3Ah
International Font
USA
France
Germany
UK
Denmark I
Sweden
Italy
Spain
Japan
Norway
Denmark II
Table 5-C International Font Set
31 n bit 0=1 bit 1=1 bit 2=1 bit 3=1 bit 4=0
Layer select
Layer 1
Layer 2
Layer 3
Layer 4
Layer 5 m bit 0=1
Show mode
Show mode 1 bit 1=1 Show mode 2
Table 5-D Layer table for saving data
DSP-880 Series Customer Pole Display
COMMAND SET
CHAPTER 7 CHARACTER SET
7.1
Character Code (20h-7Eh)
7.1.1 USA Standard Character Set
20h
0 1 2 3 4 5 6 7 8 9 A B C D E F
! “ # $ % & ‘ ( ) * + , - . /
30h 0 1 2 3 4 5 6 7 8 9 : ; < = > ?
40h @ A B C D E F G H I J K L M N O
50h P Q R S T U V W X Y Z [ \ ] ^ _
60h ﹑ a b c d e F g h i j k l m n o
70h p q r s t u V w x y z { | } ~
7.1.2 International Character Set
Character Code Number
Country
Hex 23 24 40 5B 5C 5D 5E 60 7B 7C 7D 7E
Dec 35 36 64 91 92 93 94 96 123 124 125 126
U.S.A # $ @ [ \ ] ^ ` { | } ~
France
Germany
U.K
Denmark I
Sweden
#
#
£
#
#
$
$
$
à
§
@
° ç §
Ä Ö Ü
[ \
$ @ Æ Ø
¤
É Ä Ö
^
^
]
Å
^
^
Å Ü
`
`
`
`
é
é
ä
{
æ
ä
ù
ö
|
ø
ö
è
ü
}
å
å
¨
β
~
~
ü
Italy
Spain
Japan
Norway
Denmark II
Slavonic
Russia
Portuguese
#
Pt
#
#
#
$
$
$
¤
$
@
@
@
É
É
°
¡
[
¥
Æ Ø
Æ
\
Ñ
Ø
# $ @ [ \
#
#
$
$
@
@
[
[
\
\
é
¿
^
^
] ^
Å Ü
Å Ü
]
]
]
^
^
^
ù
`
`
é æ ø
é æ ø
`
`
`
à
¨
{
{
{
{
ò
ñ
|
|
|
|
è
}
}
å
å
}
}
}
ì
~
~
ü
ü
~
~
~
DSP-880 Series Customer Pole Display 32
COMMAND SET
7.2 Character Code Page (80h-FFh)
7.2.1 Page 0 PC437: USA, Standard Europe
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
80H Ç ü é â ä à å ç ê ë è ï î ì Ä Å
90H É æ Æ ô ö ò û ù ÿ Ö Ü ¢ £
¥
Pt ƒ
A0H á í ó ú ñ Ñ a o
¿
⌐
¬ ½ ¼ ¡ « »
B0H
░ ▒ ▓ │ ┤ ╡ ╢ ╖ ╕ ╣ ║ ╗ ╝ ╜ ╛ ┐
C0H
└ ┴ ┬ ├ ─ ┼ ╞ ╟ ╚ ╔ ╩ ╦ ╠ ═ ╬ ╧
D0H
╨ ╤ ╥ ╙ ╘ ╒ ╓ ╫ ╪ ┘ ┌ █ ▄ ▌ ▐ ▀
E0H
α
ß
Γ π Σ σ μ τ Ф θ Ω δ ∞
ø є ∩
F0H
≡
±
≥ ≤ ⌠ ⌡
÷
≈
° • ·
√ n
²
■
SP
7.2.2 Greek
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
80H
Α Β Γ Δ Ε Ζ Η Θ Ι Κ Λ Μ Ν Ξ Ο Π
90H
Ρ Σ Τ
Y
Φ Х Ψ Ω α β γ δ ε ζ η θ
A0H
ι κ λ μ ν ξ ο π ρ σ s
τ υ φ χ ψ
B0H
C0H
D0H
E0H ω
F0H £ -
7.2.3 Page 2 PC850: Multilingual
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
80H Ç ü é â ä à å ç ê ë è ï î ì Ä Å
90H É æ Æ ô ö ò û ù ÿ Ö Ü ø £ Ø × ƒ
A0H á í ó ú ñ Ñ a o
¿ ® ¬ ½ ¼ ¡ « »
B0H
░ ▒ ▓ │ ┤
Á Â À ©
╣ ║ ╗ ╝
¢
¥ ┐
C0H
└ ┴ ┬ ├ ─ ┼
ã Ã
╚ ╔ ╩ ╦ ╠ ═ ╬
¤
D0H ð
Đ
Ê Ë È I Í Î Ï
┘ ┌ █ ▄ ▌ ▐ ▀
E0H Ó ß Ô Ò õ Õ
μ
þ Þ Ú Û Ù ý Ý ¯ ´
F0H ¯ ± = ¾ ¶ § ÷ , ° ¨
˙ 1 3 2 ■
SP
33 DSP-880 Series Customer Pole Display
COMMAND SET
7.2.4 Page 3 PC860: Portuguese
80H
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
Ç ü é â ä à Á ç ê Ê è ï Ô ì
Ä Å
90H
É
À È ô ö ò ú ù ì Ö Ü ø £ ù Pt ó
A0H á í
ó ú
ñ Ñ a o
¿
⌐
¬ ½ ¼ ¡ « »
B0H
░ ▒ ▓ │ ┤ ╡ ╢ ╖ ╕ ╣ ║ ╗ ╝ ╜ ╛ ┐
C0H
└ ┴ ┬ ├ ─ ┼ ╞ ╟ ╚ ╔ ╩ ╦ ╠ ═ ╬ ╧
D0H
E0H
F0H
╨ ╤ ╥ ╙ ╘ ╒ ╓ ╫ ╪ ┘ ┌ █ ▄ ▌ ▐ ▀
α ß Γ π Σ σ µ τ Φ Θ Ω δ ∞ ø ε ∩
≡ ± ≥ ≤ ⌠ ⌡ ÷ ≈
° • ·
√ ⁿ ² ■
7.2.5 Page 4 PC863: Canadian-French
80H
90H
A0H
B0H
C0H
D0H
E0H
F0H
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
Ç ü é â Â à ¶ ç ê ë è ï î = À §
É È Ê ô Ë Ï û ù ¤ Ô Ü ¢ £ Ù Û ƒ
¦ í ´ ó ú
¨
³ ¯ Î ⌐ ¬ ½ ¼ ¾ « »
░ ▒ ▓ │ ┤ ╡ ╢ ╖ ╕ ╣ ║ ╗ ╝ ╜ ╛ ┐
└ ┴ ┬ ├ ─ ┼ ╞ ╟ ╚ ╔ ╩ ╦ ╠ ═ ╬ ╧
╨ ╤ ╥ ╙ ╘ ╒ ╓ ╫ ╪ ┘ ┌ █ ▄ ▌ ▐ ▀
α ß Γ π Σ σ µ τ Φ Θ Ω δ ∞ ø ε ∩
≡ ± ≥ ≤ ⌠ ⌡ ÷ ≈
° • ·
√ ⁿ ² ■
7.2.6 Page 5 PC865: Nordic
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
80H Ç ü é â ä à å ç ê Ë è ï î ì
Ä Å
90H
É æ Æ ô ö ò û ù ÿ Ö Ü ø £ Ø Pt ƒ
A0H á í
ó ú
ñ Ñ a o
¿
⌐
¬ ½ ¼ ¡ «
B0H
░ ▒ ▓ │ ┤ ╡ ╢ ╖ ╕ ╣ ║ ╗ ╝ ╜ ╛
¤
┐
C0H
└ ┴ ┬ ├ ─ ┼ ╞ ╟ ╚ ╔ ╩ ╦ ╠ ═ ╬ ╧
D0H
E0H
F0H
╨ ╤ ╥ ╙ ╘ ╒ ╓ ╫ ╪ ┘ ┌ █ ▄ ▌ ▐ ▀
α ß Γ π Σ σ µ τ Φ Θ Ω δ ∞ ø ε ∩
≡ ± ≥ ≤ ⌠ ⌡ ÷ ≈
° • ·
√ n
²
■
DSP-880 Series Customer Pole Display 34
COMMAND SET
7.2.7 Page 6 Slavonic
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
80H Ç ü é â ä ů ć
ç
Į
ë Õ õ î
Ź
ä
Ć
90H é
Ĺ
í ô ö
Ľ ľ ś ś Ö Ü ť ť Ł х č
A0H á í ó ú ą ą ž ž ę ę
B0H
░ ▒ ▓ │ ┤
á â ĕ Ş
C0H
─ ┼ ă ă ź č ş ż
═
« ż
»
¤
D0H đ Đ Ď
Ë ď Ň
í î ě █ ▄ ţ Ů ▀
E0H Ó ß Ô ń ń ň
š š ŕ
Ú ŕ Ű
ý Ý ţ
F0H -
˝ ˛ ˇ ˘
§ ÷ ° ¨
˙ ű ŕ ř ■
́
7.2.8 Page 7 Russia
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
80H
А Б В Г Д Е Ж З и Й К Л М Н О П
90H
Р С Т У Ф Х Ц Ч Ш Щ Ъ Ы Ь Э Ю Я
A0H а б в г д е ж з и й к л м н о п
B0H
C0H
D0H
E0H р с т у ф х ц ч ш щ ъ ы ь э ю ́я
F0H
∂
K H
θ
¥ Y h
∂ k H
θ
¥ Y
7.2.9 Page 19 PC858: Multilingual + Euro Symbol
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
80H Ç ü é â ä à å ç ê ë è
ï î
ì
Ä Å
90H
É æ Æ ô ö ò û ù ÿ Ö Ü ø £ Ø × ƒ
A0H á í ó ú ñ
Ñ a o
¿ R ¬ ½ ¼ ¡ « »
B0H
░ ▒ ▓ │ ┤
Á Â À
c
¢
¥ ┐
C0H
└ ┴ ┬ ├ ─ ┼
ã Ã
D0H ð
Đ
Ê Ë È € Í Î Ï
┘ ┌ █ ▄
¤
▀
E0H Ó ß Ô Ò õ Õ
μ
þ Þ Ú Û Ù ý Ý ¯ ´
F0H ¯ ´
¯
± = ¾ ¶ ÷ ,
°
¨
•
1 3 ■
35 DSP-880 Series Customer Pole Display
COMMAND SET
7.2.10 Page 16 WPC1252: West European Latin
80H
90H
A0H
B0H
C0H
D0H
E0H
F0H
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
€ ¨ ‚ ƒ „ … † ‡ ˆ ‰ Š ‹ Œ Ž
‘ ’ “ ” • – — ˜ ™ š › œ
¡ ¢ £
¤
¥ ¦ § ¨ © ª « ¬ - ž Ÿ
® ¯
° ± ² ³ ´ µ ¶ · ¸ ¹ º » ¼ ½ ¾ ¿
À Á Â Ã Ä Å Æ Ç È É Ê Ë Ì Í Î Ï
Ð Ñ Ò Ó Ô Õ Ö × Ø Ù Ú Û Ü Ý Þ ß
à á â ã ä å æ ç è é ê ë ì í î ï
ð ñ ò ó ô õ ö ÷ ø ù ú û ü ý þ ÿ
7.2.11 Page 10 PC852: Slavonic
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
80H Ç ü é â ä ů ć ç ł ë Ő ő î Ź Ä Ć
90H É Ĺ ĺ ô ö Ľ ľ Ś ś Ö Ü Ť ť Ł × č
A0H á í ó ú Ą ą Ž ž Ę ę ¬ ź Č ş « »
B0H
░ ▒ ▓ │ ┤ Á Â Ě Ş ╣ ║ ╗ ╝ Ż ż ┐
C0H
└ ┴ ┬ ├ ─ ┼ Ă ă ╚ ╔ ╩ ╦ ╠ ═ ╬ ¤
D0H đ Ð Ď Ë ď Ň Í Î ĕ ┘ ┌ █ ▄ Ţ Ů ▀
E0H Ó ß Ô Ń ń ň Š š Ŕ Ú ŕ Ű ý Ý ţ ´
F0H ˝ ˛ ˇ ˘ § ÷ ¸ ° ¨ · ű Ř ř ■
7.2.12 Page 11 Katakana: Japanese
80H
90H
A0H
B0H
C0H
D0H
E0H
F0H
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
▁ ▂ ▃
▄
▅ ▆ ▇
█
▎ ▍
▌
▋ ▊ ▉
█ ┼
┴ ┬ ┤ ├ ‾
━ ∣ ▕
┌ ┐ └ ┘
╭ ╮ ╰ ╯
á
。 「 」 、 ‧ ヲ ァ ィ ゥ ェ ォ ャ ュ ョ ツ
ー ア イ ウ エ オ カ キ ク ケ コ サ シ ス セ ソ
タ チ ツ テ ト ナ ニ ヌ ネ ノ ハ ヒ フ ヘ ホ マ
ミ ム メ モ ヤ ユ ヨ ラ リ ル レ ロ ワ ン ゛ ゜
═ ㅑ ╪ ㅕ ◢ ◣ ◥ ◤ ♠ ♥ ♦ ♣ ● ○ ∕ ∖
╳ 円 年 月 日 時 分 秒 〒 市 區 町 村 人 ▒
DSP-880 Series Customer Pole Display 36
COMMAND SET
7.2.11 Page 12 WPC1255: Hebrew
80H
90H
A0H
B0H
C0H
D0H
E0H
F0H
א
נ
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
€ ‚ ƒ „ … † ‡ ˆ ‰ ‹
‘ ’ “ ” • – — ˜ ™ ›
NBSP ¡ ¢ £ ₪ ¥ ¦ § ¨ © × « ¬ SHY ® ¯
° ± ² ³ ´ µ ¶ · ¸ ¹ ÷ » ¼ ½ ¾ ¿
־
׀ ׁ◌ ׂ◌ ׃ װ ױ ײ ׳ ״
ב ג ד ה ו ז ח ט י ך כ ל ם
ס ע ף פ ץ צ ק ר ש ת
מ
LRM RLM
ן
7.2.11 Page 13 WPC1257: Baltic
80H
90H
A0H
B0H
C0H
D0H
E0H
F0H ą
š
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
€ ‚ „ … † ‡ ‰ ‹ ¨ ˇ ¸
Ą
Š
‘ ’ “ ” • – — ™ › ¯ ˛
NBSP ¢ £ ¤ ¦ § Ø © Ŗ « ¬ SHY ® Æ
° ± ² ³ ´ µ ¶ · ø ¹ ŗ » ¼ ½ ¾ æ
Į Ā Ć Ä Å Ę Ē Č É Ź Ė Ģ Ķ Ī Ļ
Ń Ņ Ó Ō Õ Ö × Ų Ł Ś Ū Ü Ż Ž ß į ā ć ä å ę ē č é ź ė ģ ķ ī ļ ń ņ ó ō õ ö ÷ ų ł ś ū ü ż ž ˙
37 DSP-880 Series Customer Pole Display
Download
Public link updated
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Document public link
Advertisement
