A1 A2
G
DPAK
A2
Product status link
Z0410MB
Product summary
I
T(RMS)
V
DSM
/V
RSM
I
GT
T j
max.
4 A
750 V
25 mA
125 °C
Z0410MB
Datasheet
4 A - Triac in DPAK package
Features
• 4 A Triac
• V
DRM
/ V
RRM
= 600 V and V
DSM
/ V
RSM
= 750 V
• 125 °C maximum junction temperature T j
• DPAK package
• 4 quadrants triacs with I
GT
= 25 mA
• Halogen-free molding, lead-free plating
• ECOPACK2 compliant
Applications
• Actuators
• Heating elements
• Inrush current limiting circuits
Description
The Z0410MB series is 4 A Triac housed in compact SMD DPAK. This 4 quadrants device is suited to home appliances or power tools and industrial systems and drives loads up to 4 A.
DS14021 - Rev 1 - September 2022
For further information contact your local STMicroelectronics sales office.
www.st.com
1
Z0410MB
Characteristics
Characteristics
Symbol
I
T(RMS)
I
TSM
I 2 t dl/dt
V
DRM
/V
RRM
V
DSM
/V
RSM
I
GM
P
GM
T stg
T j
T
L
Table 1. Absolute maximum ratings (limiting values)
Parameter
RMS on-state current (full sine wave)
Non repetitive surge peak on-state current (full cycle,
T j
initial = 25 °C)
I 2 t value for fusing
Critical rate of rise of on-state current, I
G
= 2 x I
≤ 100 ns, f = 120 Hz
GT
, tr
Repetitive peak off-state voltage
Non Repetitive peak off-state voltage, 10 ms
Maximum peak gate current
Maximum gate power dissipation
Storage temperature range
Operating junction temperature range
Maximum lead temperature for soldering during 10 s
T c
= 107 °C t = 16.7 ms t = 20 ms t p
= 10 ms
T j
= 125 °C
T j
= 125 °C t p
= 20 µs, T j
= 125 °C
Value
4
16
15
1.5
50
600
750
1.2
0.5
-40 to +125
-40 to +125
260
Table 2. Electrical characteristics (T j
= 25 °C, unless otherwise specified)
Symbol
I
I
GT
(1)
V
GT
V
GD
I
L
H
(2)
dV/dt
(2)
(dV/dt)c
(2)
Test conditions
V
D
= 12 V, R
L
= 33 Ω
V
D
= 12 V, R
L
= 33 Ω
V
D
= V
DRM
, R
L
= 3.3 kΩ
I
G
= 1.2 x I
GT
T j
= 125 °C
I-III-IV
II
I
T
= 500 mA, gate open
V
D
= 67 % V
DRM
; V
R
= 67 % V
RRM
, gate open T j
= 110 °C
(dI/dt)c = 1.8 A/ms T j
= 110 °C
1. For both polarities of OUT pin referenced to COM pin.
2. For both polarities of A2 referenced to A1.
Max.
Max.
Min.
Max.
Max.
Max.
Min.
Min.
Value
25
1.3
0.2
25
50
25
200
5
Symbol
V
TM
(1)
V
TO
(1)
R
D
(1)
I
DRM
/I
RRM
Test conditions
I
TM
= 5.5 A, t p
= 380 µs
Threshold voltage
Dynamic resistance
V
D
= V
R
= V
DRM
= V
RRM
Table 3. Static characteristics
T j
25 °C
125 °C
125 °C
25 °C
125°C
1. For both polarities of A2 referenced to A1.
Max.
Max.
Max.
Max.
Value
2
0.95
180
5
0.5
Unit mA
V
V mA mA mA
V/µs
V/µs
Unit
A
A
A 2 s
A/µs
W
°C
°C
°C
V
V
A
Unit
V
V mΩ
µA mA
DS14021 - Rev 1 page 2/11
Z0410MB
Characteristics
Symbol
R th(j-c)
R th(j-a)
Table 4. Thermal resistance
Parameter
Junction to case (AC)
Junction to ambient: S
CU
= 0.5 cm²
Max.
Typ.
Value
3
70
Unit
°C/W
°C/W
DS14021 - Rev 1 page 3/11
Z0410MB
Characteristics (curves)
1.1
Characteristics (curves)
Figure 1. Maximum power dissipation versus on-state
RMS current (full cycle)
Figure 2. Average and DC on-state current versus case temperature
Figure 3. On-state RMS current versus ambient temperature (full cycle)
Figure 4. Relative variation of thermal impedance versus pulse duration
Figure 5. Relative variation of gate triggering current and voltage versus junction temperature (typical values)
Figure 6. Surge peak on-state current versus number of cycles
DS14021 - Rev 1 page 4/11
Z0410MB
Characteristics (curves)
Figure 7. Non repetitive surge peak on-state current for a sinusoidal pulse with width t p
< 10 ms and corresponding value of I²t
Figure 8. On-state characteristics (maximum values)
Figure 9. Relative variation of critical rate of decrease of main current versus (dV/dt)c (typical values)
Figure 10. Relative variation of critical rate of decrease of main current versus junction temperature
Figure 11. Relative variation of static dV/dt immunity versus junction temperature
Figure 12. Thermal resistance junction to ambient versus copper surface under tab (typical values)
100
90
80
70
60
50
40
30
20
10
0
0
R th(j-a)
(°C/W)
5 10
DPAK
15 20 25 30
S
Cu
(cm²)
35 40
DS14021 - Rev 1 page 5/11
2
2.1
Z0410MB
Package information
Package information
In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: www.st.com
. ECOPACK is an ST trademark.
•
•
DPAK package information
Molding compouned resin is halogen free and meets UL94 flammability standard, level V0
Lead-free package leads plating
Figure 13. DPAK package outline
DS14021 - Rev 1 page 6/11
Note:
Z0410MB
DPAK package information
Table 5. DPAK package mechanical data
Dimensions
Ref.
L
L1
L2
L3
L4
L6
ϴ1
ϴ2
V2 c2
D
D1
E
E1 e
H
A
A1
A2 b b4 c
Min.
2.20
0.90
0.00
0.72
5.13
0.47
0.47
6.00
5.15
6.50
4.70
2.186
9.80
1.40
0.90
Millimeters
Typ.
2.30
1.01
5.33
6.10
5.40
6.60
4.85
2.286
10.10
1.50
2.90 REF
0.60
5°
5°
0°
0.51 BSC
0.80
1.80 BSC
7°
7°
1. Dimensions in inches are given for reference only
0.85
5.46
0.60
0.60
6.20
Max.
2.38
1.10
0.10
5.65
6.70
5.00
2.386
10.40
1.70
1.25
1.00
9°
9°
8°
0.0354
0.0236
5°
5°
0°
Min.
0.0866
0.0354
0.0000
0.0283
0.2020
0.0185
0.0185
0.2362
0.2028
0.2550
0.1850
0.0860
0.3858
0.0551
Inches (1)
Typ.
0.0906
0.0398
0.2098
0.2402
0.2126
0.2598
0.1909
0.0900
0.3976
0.0591
0.1142 REF
0.201 BSC
0.0315
0.0709 BSC
7°
7°
0.0492
0.0394
9°
9°
8°
This package drawing may slightly differ from the physical package. However, all the specified dimensions are guaranteed.
Max.
0.0937
0.0433
0.0039
0.335
0.2150
0.0236
0.0236
0.2441
0.2224
0.2638
0.1969
0.0940
0.4094
0.0669
DS14021 - Rev 1 page 7/11
Z0410MB
DPAK package information
Figure 14. DPAK recommended footprint (dimensions are in mm)
DS14021 - Rev 1 page 8/11
3
Ordering information
Figure 15. Ordering information scheme
Z0410MB
Ordering information
Order code
Z0410MB
Marking
Z0410MB
Table 6. Ordering information
Package
DPAK
Weight
0.3 g
Base qty.
2500
Delivery mode
Tape and reel
DS14021 - Rev 1 page 9/11
Revision history
Date
02-Sep-2022
Revision
1
Table 7. Document revision history
Changes
Initial release.
Z0410MB
DS14021 - Rev 1 page 10/11
Z0410MB
IMPORTANT NOTICE – READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgment.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. For additional information about ST trademarks, refer to www.st.com/trademarks . All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2022 STMicroelectronics – All rights reserved
DS14021 - Rev 1 page 11/11
