TS1220
Sensitive 12 A SCRs
Datasheet - production data
A
A
K
A
G DPAK
K
A
G
G
K
IPAK
A
A
K
A
G
TO-220AB
Features
On-state RMS current, I
T(RMS)
12 A
Repetitive peak off-state voltage, V
DRM
/V
RRM
600 V
Triggering gate current, I
GT
200 µA
ECOPACK ® 2 compliant component
Applications
Capacitive ignition circuit for motorcycle engine
DC brush motor drive for power tool or kitchen appliance
Gas ignitor circuit
Regulator driver for battery charger
Description
Thanks to highly sensitive triggering levels, the
12 A SCR series is suitable to fit all modes of control, found in applications such as overvoltage crowbar protection, motor control circuits in power tools and kitchen aids, inrush current limiting circuits, capacitive discharge ignition and voltage regulation circuits.
Available in through-hole or surface-mount packages, they provide an optimized performance in a limited space.
Table 1: Device summary
Order code V
DRM
/V
RRM
I
GT
Package
TS1220-600B
TS1220-600B-TR
TS1220-600H
TS1220-600T
600 V
0.2 mA
0.2 mA
0.2 mA
DPAK
DPAK
IPAK
0.2 mA TO-220AB
August 2016 DocID027645 Rev 2
This is information on a product in full production.
1/14 www.st.com
Characteristics TS1220
1 Characteristics
Table 2: Absolute ratings (limiting values)
Parameter
I
L dV/dt
V
TM
V t0
R d
I
GT
V
GT
V
GD
V
RG
I
H
I
DRM
I
RRM
Symbol
V
D
= 12 V, R
L
= 140
Ω
V
D
= V
DRM,
R
L
= 3.3 k
Ω, R
GK
= 220 Ω
I
RG
= 10 µA
I
T
= 50 mA, R
GK
= 1 kΩ
I
G
= 1 mA
,
R
GK
= 1 kΩ
V
D
= 67% V
DRM,
R
GK
= 220 Ω
I
TM
= 24 A t p
= 380 µs
Threshold voltage
Dynamic resistance
V
DRM
= V
RRM
, R
GK
= 1 kΩ
T j
= 125 °C
T j
=125 °C
T j
= 25 °C
T j
= 125 °C
T j
= 125 °C
T j
= 25 °C
T j
= 125 °C
MAX.
MAX.
MIN.
MIN.
MAX.
MAX.
MIN.
MAX.
MAX.
MAX.
MAX.
Value
6
5
1.6
0.85
30
5
2
200
0.8
0.1
8
5
Unit
I
T(RMS)
On-state RMS current (180° conduction angle)
I
T(AV)
Average on-state current (180° conduction angle)
I
TSM
I 2 t dI/dt
Non repetitive surge peak on-state current
I 2 t value for fusing
Critical rate of rise of on-state current I
G
= 2 x I
GT
, t r
≤ 100 ns
Peak gate current
T c
= 105 °C
T c
= 105 °C t p
= 8.3 ms t p
= 10 ms
T j
= 25 °C t p
= 10 ms T j
= 25 °C
F = 60 Hz T j
= 125 °C
12
8
115
110
60
50
A
A
A
A 2 s
A/µs
I
GM t p
= 20 µs T j
= 125 °C 4 A
P
G(AV)
Average gate power dissipation
T stg
Storage junction temperature range
T j
Operating junction temperature range
Symbol
T j
= 125 °C 1
- 40 to + 150
- 40 to + 125
W
°C
Table 3: Sensitive electrical characteristics (Tj = 25 °C, unless otherwise specified)
Test conditions Unit
µA
V
V
V mA mA
V/µs
V
V mΩ
µA mA
Symbol
R th(j-c)
R th(j-a)
Junction to case (DC)
Junction to ambient (DC)
Table 4: Thermal resistance
Parameter
S = 0.5 cm
2 (1)
DPAK, IPAK, TO-220AB
DPAK
IPAK
TO-220AB
Value
1.3
70
100
60
Unit
°C/W
°C/W
Notes:
(1)
S = Copper surface under tab
2/14 DocID027645 Rev 2
TS1220
1.1 Characteristics (curves)
Figure 1: Maximum average power dissipation versus average on-state current
Characteristics
Figure 2: Average and DC on-state current versus case temperature
Figure 3: Average and DC on-state current versus ambient temperature (DPAK)
Figure 4: Relative variation of thermal impedance junction to case versus pulse duration
Figure 5: Relative variation of thermal impedance junction to ambient versus pulse duration
Figure 6: Relative variation of gate trigger and holding current versus junction temperature
DocID027645 Rev 2 3/14
Characteristics
Figure 7: Relative variation of holding current versus gate-cathode resistance (typical values)
TS1220
Figure 8: Relative variation of dV/dt immunity versus gate-cathode resistance (typical values)
Figure 9: Relative variation of dV/dt immunity current versus gate-cathode capacitance (typical values)
Figure 10: Surge peak on-state current versus number of cycles
Figure 11: Non-repetitive surge peak on-state current and corresponding values versus sinusoidal pulse width
Figure 12: On-state characteristics (maximum values)
4/14 DocID027645 Rev 2
TS1220 Characteristics
Figure 13: Thermal resistance junction to ambient versus copper surface under tab (DPAK)
DocID027645 Rev 2 5/14
Package information
2
2.1
Package information
TS1220
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK ® packages, depending on their level of environmental compliance. ECOPACK ® specifications, grade definitions and product status are available at: www.st.com
.
ECOPACK ® is an ST trademark.
Lead free lead plating; halogen free molding compound.
DPAK package mechanical data
Figure 14: DPAK package outline
E b4 c2
E1
6/14 e e1 b
A1 c
L
V2
DocID027645 Rev 2
TS1220 Package information
Dim.
Min.
Table 5: DPAK mechanical data mm
Typ. Max. Min.
Inches (1)
Typ.
A
A1
A2 b
2.18
0.90
0.03
0.64
2.40
1.10
0.23
0.90
0.0858
0.0354
0.0012
0.0252 b4 c c2
D
D1
E
E1 e
4.95
0.46
0.46
5.97
4.95
6.35
4.32
2.286
5.46
0.61
0.60
6.22
5.60
6.73
5.50
0.1949
0.0181
0.0181
0.2350
0.1949
0.2500
0.1701
0.0900 e1
H
L
4.40
9.35
1.00
4.70
10.40
1.78
0.1732
0.3681
0.0394
L2
L4
V2
0.60
-8°
1.27
1.02
8°
0.0236
-8°
Notes:
(1)
Inch dimensions are for reference only.
Figure 15: DPAK recommended footprint (dimensions are in mm)
0.1850
0.4094
0.0701
0.0500
0.0402
8°
Max.
0.0945
0.0433
0.0091
0.0354
0.2150
0.0240
0.0240
0.2449
0.2205
0.2650
0.2165
DocID027645 Rev 2 7/14
Package information
2.2 IPAK package information
Figure 16: IPAK (TO-251) package outline
TS1220
8/14
This package drawing may slightly differ from the physical package. However, all the specified dimensions are guaranteed.
DocID027645 Rev 2
TS1220 e1
H
L c2
D
E e
A
A1 b b2 b4
B5 c
L1
L2
V1
Ref.
Min.
2.20
0.90
0.64
5.20
0.45
0.46
6.00
6.40
4.40
9.00
0.80
Table 6: IPAK (TO-251) package mechanical data
Dimensions
Package information
Millimiters
Typ.
Min.
Inches (1)
Typ.
Max.
0.30
Max.
2.40
1.10
0.90
0.95
5.43
0.60
0.0866
0.0354
0.0252
0.2047
0.0177
0.0125
0.0945
0.0433
0.0354
0.0374
0.2138
0.0236
2.28
0.60
6.20
6.65
4.60
0.0181
0.2362
0.2520
0.1732
0.0898
0.0236
0.2441
0.2618
0.1811
16.10
0.6339
0.80
10°
Notes:
(1)
Inch dimensions are for reference only.
9.60
1.20
1.25
0.3545
0.0315
0.0315
10°
0.3780
0.0472
0.0492
DocID027645 Rev 2 9/14
Package information
2.3 TO-220AB package information
Figure 17: TO-220AB package outline
TS1220
10/14 DocID027645 Rev 2
TS1220
Ref.
L
L1
L20
L30 e1
F
H1
J1
ØP
Q
A b b1 c
D
D1
E e
Notes:
(1)
Inch dimensions are for reference only.
10.00
2.40
4.95
1.23
6.20
2.40
13.00
3.50
Min.
4.40
0.61
1.14
0.48
15.25
Package information
Table 7: TO-220AB package mechanical data
Dimensions
Millimeters
Inches (1)
Max.
4.60
0.88
1.70
0.70
15.75
Min.
0.1732
0.0240
0.0449
0.0189
0.6004
Max.
0.1811
0.0346
0.0669
0.0276
0.6201
1.27 typ. 0.0500 typ.
10.40
2.70
5.15
1.32
6.60
2.72
14.00
3.93
0.3937
0.0945
0.1949
0.0484
0.2441
0.0945
0.5118
0.1378
0.4094
0.1063
0.2028
0.0520
0.2598
0.1071
0.5512
0.1547
16.40 typ.
28.90 typ.
0.6457 typ.
1.1378 typ.
3.75
2.65
3.85
2.95
0.1476
0.1043
0.1516
0.1161
DocID027645 Rev 2 11/14
Ordering information
3 Ordering information
Figure 18: TS1220 series
TS1220
TS 12 20 - 600 B - TR
Sensitive SCR series
Current
12 = 12 A
Sensitivity
20 = 200 µA
Voltage
600 = 600 V
Pack age
B = DPAK
H = IPAK
T = TO-220AB
Packing mode
Blank = Tube
-TR = Tape and reel
Order code
TS1220-600B
TS1220-600B-TR
TS1220-600H
TS1220-600T
Table 8: Ordering information
Marking Package Weight Base qty
TS12 20600
TS12 20600
TS12 20600
TS1220600T
DPAK
DPAK
IPAK
TO-220AB
0.3 g
0.3 g
0.3 g
2.3 g
75
2500
75
50
Delivery mode
Tube
Tape and reel
Tube
Tube
12/14 DocID027645 Rev 2
TS1220
4
Revision history
Revision history
Date Revision
Table 9: Document revision history
Changes
08-Apr-2015
03-Aug-2016
1
2
First issue.
Added section Applications and updated Features and in Table 1:
"Device summary" in cover page.
Updated Section 3: "Package information" .
Minor text changes.
DocID027645 Rev 2 13/14
TS1220
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2016 STMicroelectronics
– All rights reserved
14/14 DocID027645 Rev 2
