Schneider Electric XBTA8 Compact Terminal UNI-TE Protocol User Guide

Schneider Electric XBTA8 Compact Terminal UNI-TE Protocol allows users to communicate with a range of devices using the UNI-TE protocol. It features self-diagnostic functions to ensure optimal performance. Automatic self-tests are carried out at power-up and during the test procedure of the CONFIGURATION mode. These checks include PROM CHECK, RAM CHECK, KEYBOARD FAULT, REGISTER FAULT, EEPROM FAULT, and RUNNING. If any permanent faults are detected, the supply voltage must be switched off. The device also provides error messages to assist with troubleshooting.

PDF

文档

8
Appendices
8.1
Automatic self-tests
Whenpowering-uptheXBT-AElterminal,aseriesoftestsiscarriedout
automatically.
These tests are also carried out during the test procedure of the CONFIGURATION
mode. Thesechecks are intended to reassurethe userthattheterminal is operating
under the best conditions.
In order to quit a permanent fault, the supply voitage must be switched off.
TEST
COMMENTS
DISPLAY
!
Internal FAULT if
display permanent
ttt**t**t****ttt
PROM
CHECK. PROG XXXX
1
RAM
XBT-A8
xxx VX.X
Brief display of the
product reference and
the sofhvare version
&gt; RAM
FAULT
Memory FAULT
If display permanent =&gt;
return the product
&gt; KEYBOARD
&lt;
FAULT
c
REGISTER
%
Micro-program fault
If display permanent =&gt;
return the product
RUNNING
FAULT with keyboard
coding circuit
If display permanent =&gt;
return the product
(check that no key
is depressed)
The XBT-A8 terminal
is ready to use
t
FAULT with EEPROM
EEPROM
MESSAGE
MEMORY
z EEPROM
FAULT
&lt;
E;r;;h;.s
If fault persists =&gt;
return the product.
I$
Appendices
8.2
Error messages
MESSAGE
DISPLAYED
PROBABLE CAUSE
&gt; LINE FAULT &lt;
ADJUST MODE
Line fault
XBTffSX7
&gt; TSX DATA FAULT &lt;
ADJUST MODE
Non-existent TSX7
variable
**
--- **
(in the numeric
field)
ADJUST MODE
ASCII MODE
,XxX = NO MESSAGE&lt;
ADJUST MODE
ASCII MODE
&gt;AD PARITY FAULT&lt;
ASCII MODE
MULTIDROP
&gt;BAD RECORD&lt;
STORING
THE MESSAGES
&gt;EEPROM
98
FUNCTION
MODE
FAULT&lt;
STORING
THE MESSAGES
Value too large
for numeric field
REMEDY
-Check the wiring
-Test XBT-A8 serial port
-Testthe TSX
terminal port
-Check the position of
TSX 7 memory
cartridge lock
-Checkuse of the variabls
in the TSX7
-Check the length
of the numeric field
-Check the conversion
coefficient for the XBT-A8
No message
stored at
address XXX
-Program the message
-Change the address of
the command
Addresses wired
incorrectly
-Checkthe
Message incorrectly
witten in memory
Power switched off
during the storing
procedure
address
wiring
-Check the message
syntax
-Press
I(ENTEA)I to confirm
8
Appendices
Summary of UNI-TE
l
Messages specifically
MESSAGF
DISPLAYBD
requests
connected
FUNCl-far;l
:MDDE
with
UNI-TE protocol
PROBABLE
CAUSE
Address fault
&gt; LINE FAULT &lt;
UNI-TE
PROTOCOL
-Link between
XBT-A8 and
UNI-TELWAY
module faulty
-UNI-TELWAY station
N” wired for XET-A8
exceeds maximum
configured for module
.Module faulty
Jo response to an
(BT-A8 request
UNI-TE
&gt;NO STATION&lt;
PROTOCOL
UNI-TE
REFUSAL
STATION&lt;
PROTOCOL
JNI-TELWAY
jammeters
ncorrect,
ndicating a nonexisting or faulty
levice
Device refuses the
action requested by
he XBT-A8 because :
The variable does not
exist for this station
The action requested
is not allowed
REM WY
The XBT-A8 occupies
2 addresses on the
UNI-TELWAY bus (see
section 5.4 UNI-TELWAY
general).
Check XBT-A8 addresses
-Check the cable
between the XBT-A8
and the module
-Test the XBT-A8 serial
port (see SELF-TESTS ir
section 4.1)
-Check configuration of
the module and the
XBT-A8 station N”
-Check the results of
the module self-tests
Cheek parameters
UNI-TELWAY
NETWORK N”
STATION N”
GATE N”
MODULE N”
CHANNEL N”
in the configuration of
the serial line for operation
(section 4.3)
Check the address of the
variable associated with
the message
Check the request code
sent
99
8
Appendices
Summary of UNI-TE requests
Messages specifically
connected
with UNI-TE protocol (continued)
PROBABLE
&gt;AD PARITY FAULT&lt;
UNI-TE
CAUSE
Addresses
ncorrectly wired
PROTOCOL
NETW ADDR ERROR
UNI-TE
REMEDY
_Check
the UNI-TELWAY
address cabling
-Check TSX SCA 62
subscriber socket coding
Address fault
Same as for “Line fault”
The variable does
not exist in the TSX 7
station
Same as for
“Refusal station”
PROTOCOL
C)ATA ADDRESS ERROR
UNI-TE
PROTOCOL
UNI-TE
z-OVERFLOW&lt;
PROTOCOL
UNI-TE
INEXECUTABLE
PROTOCOL
Value entered
by the operator
too large
- Re-enter the value
If message is type F
associated with word
Confirmed without
numeric value or
with incorrect value
- Re-enter
the
numeric value
8
Amendices
8.3
Table of ASCII codes
(Characters displayed by the Latin version of XBT-A8 )
(ASCII : American Standard Code for Information Interchange).
-
b,
bi I
0
0
0
0
0
0
0
-
6
0
1
1
1
1
1
1
-
1
1
-
ifll
8
Appendices
Table of ASCII codes
(Characters displayed bythe Cyrillicversionof XBT-A8 and configured in Russian).
(ASCII : American Standard Code for informationInterchange).
ba
BINARY
bs
1100
E
1 1
0
1
C
D
1110
E
1111
F
Y
Y
/
">

您好！我是一个经过专门训练的 AI 聊天机器人，旨在帮助您了解 Schneider Electric XBTA8 Compact Terminal UNI-TE Protocol User Guide。我已经彻底审查了该文档，可以帮助您找到所需的确切信息，或者用清晰简洁的术语解释内容。无论您是在寻找有关特定功能、故障排除步骤或一般用法的指导，都可以随时提出您的问题。您提供的关于您的疑虑或需求的细节越多，我就能更准确、更有效地帮助您！