advertisement
Electrical measurement and control
M.8
Portable power analyzer
M8-2
M.8
Portable power analyzer
M.8 - Portable power analyzer
Introduction
· · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·
M8-3
AR5 / AR5-L
M8-5
C-80
M8-14
CIR-e
M8-19
CIR-e
M8-21
High voltage clamps PI-23
M8-22
Clamps with logger CPL
M8-23
T-3V
M8-24
MEG-S
M8-25
CPM
M8-26
CDB
M8-27
LXM
M8-28
MS-148
M8-28
M8-29
M8-33
Portable power analyzer
M
.8
Portable power analyzers
CIRCUTOR offers a range of portable instruments that have been designed to detect the main electrical problems in industries and installations.
M.8
Definition
These portable power analyzers offer top performance features. They have been designed to cater for the requirements of any installation and type of measurement.
The AR5 / AR5-L types have an internal memory that stores all parameters required: fully programmable. In addition, the same analyzer can have various types of software and their applications will be used in different types of analysis.
What are the advantages of portable power analyzers?
1. Savings
x
Detection and prevention of excess consumption (kW ·h)
Analysis of load curves to see the points of maximum demand of energy.
Detection of the need for a capacitor bank in an installation, as well as their power.Detection of fraud in energy meters.
2. Prevention
x
The AR5 series has been specially designed for the periodic maintenance of the status of low and medium voltage electrical networks; to check the motor start-up curves, detect potential saturations in the power transformer, power cuts, deficient quality of the power supply, etc.
3. Resolution
x
Analysis of the source of problems in the electrical network in order to solve the problems of unforeseen trips, earth leakages, cable heating, resonance, harmonics, disturbances,
flicker, phase unbalances, etc. At the same time, you can design the adequate size of active or passive harmonic filters and filters for speed variators, etc.
M8-3
M
.8
Portable power analyzer
Example of an application with AR5-L, observing the wave quality in PowerVision
Example of an application with AR5-L, observing the harmonics in PowerVision
4. Analysis programs
CIRCUTOR offers 6 types of programs
(only for AR5 / AR5-L) :
1. Harmonics: Analysis of all electrical parameters: voltage, current, power, energy and a long etcetera.
2. Disturbances - Power supply
quality: Detection of interruptions, gaps, overvoltages or any alteration in the wave shape.
3. Flicker:
The flicker in the installation can be studied.
4. Fast Check – Motor start-up: Single or three-phase studies can be performed to capture the voltage, current, power and power factor during cycle periods.
5. Check
Meter: Checks the measurements of electronic and mechanical meters. It also determines the errors in active energy or PF meters.
6. Leak Meter: Detection and analysis of leakages (earth leakages).
7. File Vision: Display of the records on the unit, with no need for a PC.
Applications
Performing energy studies of the wave quality and disturbances.
M8-4
AR5 / AR5-L
Portable single and three-phase power analyzer
Portable power analyzer
M
.8
Description
}
Measures all of the main electrical parameters of an electricity network
}
Measurement in true root mean square
}
Built-in energy meter
}
With 4 voltage channels and 4 current channels (AR5-L)
}
Configurable auto-trigger, depending on the parameters required
}
Languages: Spanish and English
}
Large backlit LCD display
}
CAT III 600 V (EN 61010). UL
Certificate
}
Display of up to 30 electrical parameters on the screen
}
Small size and reduced weight, only
800 g
}
Independent files for each measurement
}
Including the powerful analysis software:
POWER VISION
}
Configurable with menus
}
Optional operation with no external power supply, with an autonomy of up to 8 hours
}
RS-232 Communications with PC
}
Clamp auto-detection
}
Auto-selection of parameters stored
}
Calculation of the time remaining until the memory is full
}
Linear or rotating memory (depending on the configuration)
Features
Power supply circuit
Through an external power supply unit
Frequency
Consumption
Operating temperature
Altitude
Humidity of operation
Measurement circuit
Contamination level
Voltage circuit
Measurement range
Voltage and current transformation ratios
Measurement units
Internal memory
Accuracy class (*)
Voltage
Current
Active power
Power factor
Build features
Housing
Keyboard / Display
Display
Current clamp connector
Dimensions
Weight
RS-232 Outputs
AR5 AR5-L
100...240 V ac / 12 V dc
50...60 Hz
15 V ·A
0...+40 ºC
≤ 2 000 m
80 % for temperatures under 31 ºC, with a linear decrease down to 50 % at 40 ºC
Three-phase (3 wires) Three-phase (3 / 4 wires)
2
In accordance with the clamp, 0.01 A...20 kA
Programmable
Automatic change of scale
1 Mb
0.5 % ± 2 digits
0.5 % ± 2 digits
1 % ± 2 digits
1 % ± 2 digits
Reinforced insulation
On the front panel
LCD 160 x 160 pixels (backlit)
3 3 / 4
220 x 60 x 130 mm
800 g
Series output
M8-5
M
.8
Portable power analyzer
AR5 / AR5-L
Portable single and three-phase power analyzer
Application
}
Complete study of the installation where the analyzer is capable of gathering different types of records: harmonics, disturbances, meter verification, transients, flicker, etc.
Features
AR5 AR5-L
Safety
Standards
EN 61000-3-2 (1995), Harmonics
EN 61000-3-3 (1995), Voltage fluctuations
Category III - 600 V, in accordance with 61010
EN 61000-6-4 (2002), Industrial emissions
EN 55011 (1994), Driven (EN 52022 – Class B)
EN 55011 (1994), Radiated (EN 55022 – Class A)
EN 61000-6-2 (2022), Industrial immunity
EN 61000-4-2 (1995), Electrostatic discharge
ENV 50140 (1993), Radiated electromagnetic field
EN 61000-4-8 (1995), Rapid transient bursts
ENV 50141 (1993), RF in common mode
EN 61000-4-8 (1995), Magnetic field at 50 Hz
EN 61000-6-1 (2002), Domestic immunity
EN 61000-4-5 (1995), Shockwave
EN 61000-4-11 (1994), Power supply interruptions
(*) Accuracy is given by the following measurement conditions: Exclusion of errors produced by the clamps and external voltage transformers, with a range of temperature of 5 ... 45 ºC and power factor of 0 ... 1
References
Analyzer
AR5
AR5-L
-
-
Clamps Program
Energy / Harmonics
Energy / Harmonics
Transport
Units
Carrying Bag
Type
AR5- Power analyzer with 3 current inputs
Carrying Bag
AR5-L- Power analyzer with 4 current inputs
AR5
AR5
AR5
AR5
3 x CPR-1000
3 x CP-2000 / 200
3 x CP-2000 / 200
3 x CP-5
3 x CPR-500
Energy / Harmonics
Energy / Harmonics
Energy / Harmonics and Disturbances
Energy / Harmonics and Disturbances
AR5 Kits
Carrying Bag
3 AR5 Kit
Carrying Bag
Carrying Bag
Carrying Bag
4 AR5 Kit
5 AR5 Kit
9 AR5-RBT Kit
AR5-L Kits
AR5-L
AR5-L
AR5-L
3 x CPR-1000
1 x CPR-500
3 x CPR-2000/200
1 x CPR-1000
3 x CPR-2000/200
1 x CPR-10003 x CP-5
3 x C-FLEX–45 cm
1 x CF-5
Energy / Harmonics
Energy / Harmonics
Energy / Harmonics and Disturbances
AR5-L
Energy / Harmonics and Disturbances
AR5-L
AR5-L
AR5-L
3 x C-FLEX-80 cm
1 x CF-5
3 x C-FLEX-45 cm
1 x CF-5
3 x C-FLEX-80 cm
1 x CF-5
Energy / Harmonics and Disturbances
Energy / Harmonics and Disturbances
Energy / Harmonics and Disturbances
The two analyzers include: 3 voltage cables + power supply
Carrying Bag
Carrying Bag
Carrying Bag
Carrying Bag
Carrying Bag
Case
Case
3 L AR5-L
4 L AR5-L
5 L AR5-L
11 L AR5-L-RBT
12 L AR5-L-RBT
11 LM AR5-L-RBT
12 LM AR5-L-RBT
All kits include: 3 voltage cables + power supply + PowerVision software + energy / harmonics program + 3 clamps
Code
M80103
M80111
M80711
M80721
M80732
M80781
M80811
M80821
M80832
M80843
M80853
M80643
M80653
M8-6
Portable power analyzer
M
.8
AR5 / AR5-L
Portable single and three-phase power analyzer
Parameters measured
Three-phase system, 4 wires
Parameter
phase-neutral voltage
Current
Neutral current
(only AR5-L)
Frequency
Active power
Power factor L
Power factor C
Apparent power
Power factor
Active energy
Power factor L
Power factor C
Voltage harmonics
Current harmonics
Current harmonics on neutral (only AR5-L)
I
N
Symbol
(unit)
V
A
Hz kW kvarL kvarC kVA
PF kW ·h kvar ·h L kvar ·h C
L1 L2
Yes Yes
Yes Yes
Yes
Yes -
Yes Yes
Yes Yes
-
Yes Yes
-
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes Yes
Yes
L3
Yes
Yes
Yes
Yes
Yes
Yes
-
Yes
Yes
-
Yes
Yes
Yes
-
-
Yes
Yes
-
Yes
Yes
Yes
Yes
Yes
Yes
-
Three-phase value
Yes
Three-phase system, 3 wires
Parameter
phase-phase voltage
Current
Frequency
Active power
Power factor L
Power factor C
Apparent power
Power factor
Active energy
Power factor L
Power factor C
Voltage harmonics
Current harmonics
V
A
Symbol
(unit)
Hz kW kvarL kvarC kVA -
Yes
PF kW ·h kvar ·h L -
-
Yes
L1-L2
Yes
Yes
Yes
Yes
Yes kvar ·h C -
Yes
Yes
-
Yes
-
-
Yes
L2-
L3
Yes
Yes
-
Yes
Yes
-
Yes
Yes
-
Yes
-
-
Yes
L3-L1
Yes
-
Yes
Yes
Yes
-
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Three-phase value
-
Yes
-
Yes
Yes
-
-
Yes
Two-phase System
Parameter
phase-phase voltage
Current
Neutral current
(only AR5-L)
Frequency
Active power
Power factor L
Power factor C
Apparent power
I
Symbol
(unit)
V
A
N
Hz kW kvar L kvar C kVA
-
L1-N L2-N
Yes
Yes
Power factor PF Yes
Active energy
Power factor L
Power factor C
Voltage harmonics
Current harmonics
Current harmonics on neutral (only AR5-L) kW ·h kvar ·h L -
kvar ·h C -
Yes
Yes
Yes
Yes
Yes
-
Yes
Yes
-
-
-
-
Yes
Yes
Yes
Yes
Yes
Yes
-
Yes
Yes -
-
Two-phase value L1 - L2
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-
Yes
Parameter
phase-phase voltage
Current
Frequency
Active power
Power factor L
Power factor C
Apparent power
Power factor
Active energy
Power factor L
Power factor C
Voltage harmonics
Current harmonics
Single-phase system
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
L1-N
Yes
Yes
Yes
Yes
Yes
Symbol
(unit)
V
A
Hz kW kvarL kvarL / (-C) kVA
PF kW ·h kvar ·h L kvar ·h C
M8-7
M
.8
Portable power analyzer
Programs
AR5 / AR5-L
Portable single and three-phase power analyzer
M8-8
Programs
Description
Updating harmonics
Flicker (PST and PLT assessment)
Detection of network disturbances
CHECK METER, meter verification system
Optic fibre sensor, shunts and CHECK METER program included
FAST CHECK, motor start-up
LEAK METER, detection and analysis of leakages
FILE VISION, display of files in AR5-L
Equipment
AR5 and AR5-L
AR5 and AR5-L
AR5 and AR5-L
AR5 and AR5-L
AR5-L
AR5 and AR5-L
AR5 and AR5-L
AR5-L
Type
Updating ARI
FL Program
PERTURB Program
CM Program
Optical check meter kit
Fast Program
Leak Program
Fil Vision Program
Code
M80221
M80223
M80224
M80225
M806B3
M80226
M80229
M8022A
Memory capacity example: In the Energy program, if you record 30 network parameters, with a registration period of 15 minutes, you obtain an autonomy of 80 days of memory.
Harmonics
The harmonics program can be used for the following:
}
Analysis of all electrical parameters: voltage, current, power, energy, etc.
}
Analysis of overheating in transformers, capacitors, etc.
}
Detection of neutral current
}
Wave shapes shown on the display in real time
}
Zoom on a wave shape
}
Harmonic decomposition display (30 or
50 harmonics)
}
Calculation of the THD % in voltage and current
Applications:
}
Calculation of the diameter of cable required to support losses produced by harmonics
}
Study of harmonic filtering applications
}
Comparison of measurements taken, in accordance with the IEC standard
}
Energy and billing study
}
Study of installation consumption
}
Analysis of the power factor compensation
Graphical representation of:
}
Wave shapes and harmonic distortion
}
Total harmonic distortion THD %
}
Harmonic decomposition (up to order 50)
}
True root mean square values for voltage and current
}
It can be used to prepare tables and lists
}
The direction of harmonics can be seen with software
Type
Updating ARI
Code
M80221
Programs
AR5 / AR5-L
Portable single and three-phase power analyzer
Network quality - Disturbances
Program applications:
}
Detection of interruptions, gaps, microcuts, peaks, etc.
}
Adjustment of the sensitivity for the capture of different types of disturbances
}
Information about the number of disturbances detected
}
Applications
}
Check the effect of switching a load over various points of the installation
}
Take "x-rays" of any installation with an
AR5 unit and a PC, in order to know everything about a supply network: x
Evolution of the wave shape x
Display of an alterationChecking the three phases during the alteration
Type
PERTURB Program
Flicker
The flicker program can be used to:
}
Study the flicker present in the installation, whether it is instantaneous, PST or PLT (the latter via software)
}
Carry out the same operations executed by the energy program
}
Configuration of the times for the calculation of the flicker and energy
}
Flicker parameters on a single screen
}
Applications
}
Determine the level of visual disturbance that can lead to a decrease in the performance of workers
}
Study voltage fluctuations
Type
FL Program
Code
M80224
Code
M80223
Motor start-up (Fast check)
This program can be used to:
}
Perform studies on single or three-phase networks to capture the voltage, current, power and power factor during cycle periods
}
Capture short voltages (for ex.: motor start-up, welding machines, etc.)
}
Potential recording with a
trigger
}
Fixed or rotating memory
Type
Fast Program
Code
M80226
Portable power analyzer
M
.8
M8-9
M
.8
Portable power analyzer
Programs
AR5 / AR5-L
Portable single and three-phase power analyzer
Check-Meter
The program can be used to:
}
Check the measurements of electronic and mechanical meters
}
Carry out the tests with no energy cuts
}
Carry out 30-second long tests
}
Determine the error in active energy or power factor meters
}
Programmed setup and percentage error on a single screen
}
Up to 4000 records can be created
}
Numerical table
}
Export to .bmp format or to the clampboard
Applications
Meter verification studies, creation of detailed reports in each measurement point
}
Detection of errors that exceed 1 % (with the AR5-L-shunts calibrated set) in electricity meters
}
Detect potential fraud situations
Optical reader kit
}
For electronic meters or meters with verification LED
}
Optic fibre cable used to check meters
}
Communications and power supply cable connected to AR5
}
Measures impulses with a longitude that exceeds 1 us
}
Shock-proof plastic
}
Reduced dimensions: 64x41x26 mm
Type
CM optical kit
(includes sensor, shunts, program and software )
Code
M806C3
Type
CM Program
Code
M80225
M8-10
Leak (only AR5-L)
}
Measurement of leakage current, up to
10 A, with a transformer
}
Measurement with current sensing clamp
}
Measurement with earth leakage transformers
}
Measurement scales with 2 mA ... 1 A clamp and 20 mA ... 10 A clamp
}
Filtering of high frequencies to avoid the effect of switching systems
}
Measurement of the true root mean square value during each period (20 ms)
}
Continuous measurement with a record of each period of the programmed time
}
Programmable record time 1 s ... 100 s
}
Detection of the trip moment due to a voltage drop
}
Detection of the trip moment, depending on the programmed leakage level
ApplicationsDetection of the trip level of protection relays
}
Checking leakages with no need for manual analysis on the site
Type
Leak Meter Program
Code
M80229
Programs
AR5 / AR5-L
Portable single and three-phase power analyzer
File Vision (only AR5-L)
}
On-site verification of records
}
Display of records, with no need for a PC
}
The screen has a cursor that indicates the position of the value of the variable selected, in terms of record time and parameter
}
Auto-scalable axis of the parameter
(adapted to the maximum and minimum values of all records
}
Permanent display of 32 records on the screen
}
Display of the maximum and minimum value of the records
}
You can browse through records easily and quickly
}
Variables represented by the different programs:
Type
File Vision
x
Harmonics: Vpp, Vpn, A, W, var L, var C,
PF, Hz, V ·A, I
N
, kW ·h x
Check-Phase: Vpp, Vpn, A, W, var L, var
C, PF, Hz, V ·A, I
N
, kW ·h x
Flicker: Vpp, Vpn, A, W, var L, var C, PF,
Hz, V ·A, I
N
, kW ·h, Pst x
Fast-Check: Vpp, Vpn, A, W, var L, var C,
PF, Hz, V ·A, I
N
Code
M8022A
Connections
Three-phase system, 4 wires Three-phase system, 3 wires, ARON
Portable power analyzer
M
.8
Three-phase system, 3 wires
Single-phase system
Dimensions
M8-11
M
.8
Portable power analyzer
Clamps
AR5 / AR5-L
Portable single and three-phase power analyzer
Clamps CF-5 CF-10 CP-5 CP-100 CPR-500 CPR-1000 CP-2000 / 200
Measurement range
1...1000 A ac
Nominal frequency 48...65 Hz
Output voltage 2 V ac
Dielectric rigidity
Scale base error
5200 V,
50 Hz,1 min
0.2 mA...10 A ac 0.05..0.5 A ac 1...100 A ac
48...65 Hz
2 V ac
5200 V,
50 Hz,1 min
1 % (up to 0.1 A)
0.5 % (Up to 5 A)
-0,35 %
48...65 Hz
2 V ac
5200 V, 50
Hz, 1 min
1 %
48...65 Hz
2 V ac
5200 V, 50
Hz, 1 min
0,5 %
1...500 A ac
48...65 Hz
2 V ac
5200 V, 50 Hz,
1 min
0,7 %
1...1000 A ac
48...65 Hz
2 V ac
5200 V, 50
Hz, 1 min
0,7 %
1...200 A ac
10...2000 A ac
48...65 Hz
2 V ac
5200 V, 50 Hz, 1 min
Scale 200: 0.5
% (+70 mA)
Scale 2000: 0.5%
(+100 mA)
64 mm
Maximum conductor diameter
20 mm 100 mm 20 mm 20 mm
Maximum busbar
1 - 50 x 5 mm or
4 - 30 x 5 mm
5 - 80 x 5 mm or
3 - 80 x 10 mm
20 x 5 mm 20 x 5 mm
Description
/ Code
52 mm 52 mm
1 - 50 x 5 mm or
4 - 30 x 5 mm
1 - 50 x 5 mm or
4 - 30 x 5 mm
5 - 125 x 5 mm or
3 - 100 x 10 mm
CF-5
Code M81331
CF-10
Code M81334
3 CP-5 Kit
Code M81041
3 CP-100 Kit
Code M81042
1 CP-
100Neutral clamp (blue)
Code M81036
3 CPR500 Kit
Code M81043
1 CPR-500Neutral clamp (blue)
Code M81037
3 CPR-1000 Kit
Code M81044
1 CPR-1000 -
Neutral clamp
(blue)Code
M81038
3 CP-2000/200 Kit
Code M81045
M8-12
Portable power analyzer
Clamps
AR5 / AR5-L
Portable single and three-phase power analyzer
Clamps C-FLEX 20000/2000/200 A-120 C-FLEX 20000/2000/200 A-80 C-FLEX 20000/2000/200 A-45
M
.8
Longitude sensor
Scales
Sensitivity in mV
Measurement amplitude
Bandwidth
Accuracy
Electrical safety
120 cm
200 A / 2000 A / 20000 A or
100 A / 1000 A / 10000 A
Scale 200 or 100: 10 mV / A
Scale 2000 or 1000: 1 mV /
AScale 20k or 10k: 0.1 mV / A
5 A...20 kA
10...20 kHz
1 %
Double insulation
IEC 1010 - 100 V - Cat III -
Degree of contamination 2
600 V (peak factor 1.5)
80 cm
200 A / 2000 A / 20000 A or
100 A / 1000 A / 10000 A
Scale 200 or 100: 10 mV / A
Scale 2000 or 1000: 1 mV /
AScale 20k or 10k: 0.1 mV / A
5 A...20 kA
10...20 kHz
1 %
Double insulation
IEC 1010 - 100 V - Cat III -
Degree of contamination 2
Admissible output overvoltage
Ambient conditions
Temperature
Humidity type kit
Code
600 V (peak factor 1.5)
-10...+55 ºC
90 % HR (at 50 ºC)
-10...+55 ºC
90 % HR (at 50 ºC)
Kit 3 C-FLEX 20000/2000/200 A-80 Kit Kit 3 C-FLEX 20000/2000/200 A-80
M81142 M81142
45 cm
200 A / 2000 A / 20000 A or100
A / 1000 A / 10000 A
Scale 200 or 100: 10 mV / A
Scale 2000 or 1000: 1 mV / AScale
20k or 10k: 0.1 mV / A
5 A...20 kA
10...20 kHz
1 %
Double insulation
IEC 1010 - 100 V - Cat III -
Degree of contamination 2
600 V (peak factor 1.5)
-10...+55 ºC
90 % HR (at 50 ºC)
Kit 3 C-FLEX 20000/2000/200 A-45
M81141
M8-13
M
.8
Portable power analyzer
C-80
Portable single and three-phase power analyzer
M8-14
Description
}
Measurement of the main electrical parameters of a single-phase network, balanced three-phase network and unbalanced three-phase network with neutral
}
Measurement of energy
}
Measurement of the THD in A and V
}
Detects leakage currents and the turning direction of phases
}
Internal memory to record parameters automatically
}
Display of the maximum and minimum values of electrical parameters
}
Reduced size and weight (300g) very robust and easy to use
}
Auto-detection of clamp
Application
}
Calculation of the capacity in kvar to compensate the installation
}
Display of energies compensated with a determined capacitor bank
}
Creation of harmonic distortion alarms to detect resonances
Features
Power supply circuit
Voltage
Measurement circuit
Nominal voltage
Frequency
Nominal current
Voltage overload
Current overload
Class/Accuracy
Voltage
Current
Power rating
Build features
2 x 1,5 V dc (LR6 AA-type batteries)
50 ... 500 Vac
45 ... 65 Hz
2 V (automatic, depending on the clamp)
10% (550 V ac)
10%
0.5% ± 2 digits
0.5% ± 2 digits
1% ± 2 digits
Operating autonomy
Keyboard
Display
Voltage terminals
Current clamp connector
Record
Dimensions
Weight
Accepted clamps
200 hours
1 on/off + 7 function keys
7 segments, 3 lines x 4 digits, indication icons
L1, L2, L3 / N
4 wires (ID signal -> automatic detection)
Circular file (between 1 and 90 min)
172 x 100 x 50 mm
300 g
CP 2000/200, CP 1000, CP 500, CP 100,
CP 5, CF-5, C-FLEX 200 / 2000 / 20000
Safety
IEC 61010-6-1
Standards
IEC 61000-6-3: 1996, Emissions in residential and commercial environments and light industry
CISPR 11:1997 MOD, Radiated (CISPR 22: 1997 MOD-Class A)
IEC 61000-6-4: 1997, Emissions in industrial environments.
CISPR 11: 1997 MOD, Radiated (CISPR 22: 1997 MOD-Class A)
IEC 61000-6-2:1999, Immunity in industrial environments
IEC 61000-4-2:1995, Electrostatic discharge
IEC 61000-4-3:2002, Radiated electromagnetic field
IEC 61000-4-4:1995, Rapid transient bursts
IEC 61000-4-5:1995, Shockwaves
IEC 61000-4-6:1996, RF in common mode
IEC 61000-4-8:1993, Magnetic field at 50 Hz
IEC 61000-6-1:1997, Immunity in residential and commercial environments and light industry
IEC 61000-4-5:1995, Shockwaves
IEC 61010-6-1:2001, Electrical security
Portable power analyzer
C-80
Portable single and three-phase power analyzer
References
Analyzer Clamps Type
C-80, Power analyzer
Code
M80120
Kits
C-80 / 1000
C-80 / 2000
C-80 / C-FLEX 45
M80121
M80122
M80123
C-80 / C-FLEX 80 M80124
C-80 / C-FLEX 45 M80125
All kits include 3 voltage cables + case
Balanced Three-phase System Balanced single-phase system
Parameters measured
Parameter
Voltage
Current
Frequency
Active power
Reactive power
(L and C)
Apparent power
Power factor
Cos ϕ
Active energy
Power factor (L)
Power factor (C)
THD (%) U, I
MD (Max demand) var
Symbol
(unit)
V
A
Hz
W
Balanced Three-phase /
Single-phase system
Instantaneous Maximum Minimum
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes -
-
Yes
Yes
Yes
V · A Yes
PF cos ϕ
W · h
Yes
Yes
Yes var · h L Yes var · h C Yes
% THD Yes
PD Yes
-
-
Yes
Yes
Yes
Yes
-
Yes
Yes
-
-
-
-
-
-
-
-
-
M
.8
Umbalanced Three-phase System with neutral Dimensions
M8-15
M
.8
Portable power analyzer
Clamps
C-80
Clamps CP-5 CP-100 CPR-1000 CPR-500 CP-2000 / 200
Measurement range
Nominal frequency
Output voltage
Dielectric rigidity
0.05..0.5 A ac
48...65 Hz
2 V ac
5200 V, 50
Hz, 1 min
1...100 A ac
48...65 Hz
2 V ac
5200 V, 50
Hz, 1 min
1...1000 A ac
48...65 Hz
2 V ac
5200 V, 50 Hz, 1 min
1...500 A ac
48...65 Hz
2 Vac
5200 V, 50 Hz, 1 min
1...200 A ac
10...2000 A ac
48...65 Hz
2 V ac
5200 V, 50 Hz, 1 min
Scale base error 1 % 0,5 % 0,7 % 0,7 %
Scale 200: 0.5 % (+70 mA)
Scale 2000: 0.5% (+100 mA)
Maximum conductor diameter
Maximum busbar
20 mm
20 x 5 mm
20 mm
20 x 5 mm
52 mm
1 - 50 x 5 mm or
4 - 30 x 5 mm
52 mm
1 - 50 x 5 mm or
4 - 30 x 5 mm
64 mm
5 - 125 x 5 mm or
3 - 100 x 10 mm
Description
Code
CP-5
Code M81031
CP-100N
Code M81032
CPR-1000
Code M81034
CPR-500
Code M81033
CP-2000/200
Code M81035
M8-16
Portable power analyzer
M
.8
Clamps
C-80
C-FLEX Clamps 20 000 / 2000 / 200 A-120
Longitude sensor
Scales
Sensitivity in mV
Measurement amplitude
Bandwidth
Accuracy
Electrical safety
120 cm
200 A / 2000 A / 20000 A or
100 A / 1000 A / 10000 A
Scale 200 or 100: 10 mV / A
Scale 2000 or 1000: 1 mV /
AScale 20k or 10k: 0.1 mV / A
5 A...20 kA
10...20 kHz
1 %
Double insulation
IEC 1010 - 100 V - Cat III -
Degree of contamination 2
600 V (peak factor 1.5) Admissible output overvoltage
Ambient conditions
Temperature
Humidity
-10...+55 ºC
90 % HR (at 50 ºC)
Scales
20 kA / 2000 A / 200 A
10 kA / 1000 A / 100 A
Type
C-FLEX
20000 / 2000 / 200 A-120
Code
M81153
C-FLEX
10000 / 1000 / 100 A-120
M81653
* Codes for 1 clamp
C-FLEX Clamps 20 000 / 2000 / 200 A-80
Longitude sensor
Scales
Sensitivity in mV
Measurement amplitude
Bandwidth
Accuracy
Electrical safety
80 cm
200 A / 2000 A / 20000 A or
100 A / 1000 A / 10000 A
Scale 200 or 100: 10 mV / A
Scale 2000 or 1000: 1 mV /
AScale 20k or 10k: 0.1 mV / A
5 A...20 kA
10...20 kHz
1 %
Double insulation
IEC 1010 - 100 V - Cat III -
Degree of contamination 2
Admissible output overvoltage
Ambient conditions
Temperature
Humidity
600 V (peak factor 1.5)
-10...+55 ºC
90 % HR (at 50 ºC)
Scales
20 kA / 2000 A / 200 A
10 kA / 1000 A / 100 A
Type
C-FLEX
20000 / 2000 / 200 A-80
Code
M81152
C-FLEX
10000 / 1000 / 100 A-80
M81652
* Codes for 1 clamp
Longitude sensor
Scales
Sensitivity in mV
Measurement amplitude
Bandwidth
Accuracy
Electrical safety
45 cm
200 A / 2000 A / 20000 A or
100 A / 1000 A / 10000 A
Scale 200 or 100: 10 mV / A
Scale 2000 or 1000: 1 mV /
AScale 20k or 10k: 0.1 mV / A
5 A...20 kA
10...20 kHz
1 %
Double insulation
IEC 1010 - 100 V - Cat III -
Degree of contamination 2
600 V (peak factor 1.5) Admissible output overvoltage
Ambient conditions
Temperature
Humidity
Scales
20 kA / 2000 A / 200 A
10 kA / 1000 A / 100 A
-10...+55 ºC
90 % HR (at 50 ºC)
Type
C-FLEX
20000/2000/200 A-45
C-FLEX
10000/1000/100 A-45
Code
M81151
M81651
M8-17
M
.8
Portable power analyzer
CIR-e
3
M8-18
Description
} is a portable high performance recorder designed for energy audits. Its design and easy operation make it ideal for carrying out energy studies.
}
4 quadrants
}
Measurement in true root mean square
}
Built-in energy meter
}
With 4 voltage channels and 3 current channels
}
SD card to store the parameters (up 2Gb)
}
Compatible with software Power Vision.
}
Power supply 100…400 Vac and 70…315 Vdc
}
Reduced size and weight (300g) very robust and easy to use
}
Auto-detection of clamp
}
indication of an incorrect connection
}
The measurement unit includes the right of use of the associated software that is required to handle the energy data of the CIRe³ Web application
}
Magnet fixing
Application
Most portable recorders in the market follow highly complex parameters configuration and start-up processes. CIR-e
3
has been designed with the purpose of simplifying the setup and execution of measurements and, as a consequence, the analysis of energy audit studies.
}
Energy audits in installations
}
Preventive control and maintenance of substations
}
Subcontracting energy audits
Features
Power supply circuit
Voltage
Frequency consumption
100...400 V ac, 70...315 V dc
50...60 Hz
9 V ·A
Measurement circuit
Voltage (ph-N )
Voltage ph-ph
Current (.../2 V)
Frequency
Maximum/minimum current, about the clamp and scale
Clamps
Scale
E-FLEX 20/54 cm
L1/sc1
L2/sc2
L3/sc3
200 A
2 000 A
CP-5
CP-100
Accuracy
10...400 V ac (ph-N) ± 10%
17...520 V ac (ph-ph) ± 10%
2,5...100 % FS
45...65 Hz
20 000 A
5 A
100 A
Range
5...200 A
50...2 000 A
500...20 000 A
0,05...5 A
1...100 A
Voltage
Current
Active power
0,5 % FS
1 % FS
2 % FS
Energy
Others feautres
Working temperature
Altitude
Humidity
Storage temperature
Protection
Weight (only CIRe3) weight (with packaging)
Standards
2 % FS
10...50 ºC
2 000 m
95 % HR without condensation
-10...65 ºC
IP 53
0,677 kg
0,733 kg
ELECTRICAL SAFETY REGULATIONS: IEC 60664-1, IEC 61010-1,IEC 62053-21, UL 94, VDE 110
ELECTROMAGNETIC EMISSIONS: IEC 61000-3-2, IEC 61000-3-3, IEC 61000-6-4, EN 55011, EN 55022
ELECTROMAGNETIC IMMUNITY: IEC 61000-6-2, IEC 61000-4-2, IEC 61000-4-3, IEC
61000-4-4, IEC 61000-4-5, IEC 61000-4-8, IEC 61000-6-1, IEC 61000-4-11, ENV 50141
Portable power analyzer
M
.8
CIR-e
3
Portable single and three-phase power analyzer
Parameter
Voltage
Current
Frequency
Active Power
Reactive Power (L & C)
Apparent Power
Power Factor
Active Energy
Reactive Energy ( L & C )
Aparent energy
Harmonic decomposition
U, I (50)
THD (%) U, I
MD (Max demand) - act.Pow
MD (Max demand) -App.Pow
Fundamental U, I
Flicker WA
Flicker Pst
Symbol
(unit)
V
A
Hz
W varL, varC
V · A
FP
W ·h var ·hL,var ·hC
V ·A ·h
L1 L2 L3 III
Yes Yes Yes
Yes Yes Yes
Yes
Max./
Min.
Yes
Yes
Yes
Yes Yes Yes Yes Yes
Yes Yes Yes Yes Yes
Yes Yes Yes Yes Yes
Yes Yes Yes Yes Yes
Yes
Yes
Yes
% THD
W (MD)
V ·A (MD)
WA
Pst
Yes Yes Yes
Yes Yes Yes
Yes Yes
Yes Yes
Yes Yes Yes
Yes Yes Yes
Yes Yes Yes Yes Yes
Connections
Umbalanced three-phase system
References
Analyzer
CIR-e 3 -
Clamps Type
CIR-e 3
Code
M85020
CIR-e 3 E-FLEX 54
Kit 3 clamps CP-100 CIR-e
3
CIR-e 3 E-FLEX 54 M85000
Accesories
Kit 3 clamps E-FLEX 54 200/2.00/20.000 A
Kit 3 clamps CP-5 CIR-e
3
M86010
M86011
M86012
kit 6 Voltage cables
Carring case
M86020
M89931
Balanced single-phase system
Dimensions
L 1
L 2
L 3
N
Alimentación auxiliar
Power supply
L 1
N
Alimentación auxiliar
Power supply
Magnetic fixing
M8-19
M
.8
Portable power analyzer
CIR-e
Q
Description
}
Voltage measurement
}
Voltage quality measurement parameters
}
Configurable by pC
}
Store electric parameters and voltage events in SD card (up to 2 GB)
}
Posibility of external power supply
100…400 Vac and 70…315 Vdc
}
Reduced size and weight (300g) very robust and easy to use
}
The measurement unit includes the right of use of the associated software that is required to handle the data of the CIR-e
Q
Web application (STD file)
}
Magnet fixing
Application
} has been designed to incorporate the latest technologies and it offers the most advanced performance features in the market for the measurement and recording of the electrical parameters of electrical networks
features
Power supply circuit
Voltage
Frequency
Consumption 100 / 400 Vac
Consumption 70 / 315 Vdc
Measurement circuit
Voltage ( ph-N )
Voltage
ph-ph
Frequency
Accuracy
Others features
Working temperature
100...400 V c.a., 70...315 V c.c.
50...60 Hz
5,2 / 22 V ·A
3 W
10...400 V ac. (ph-N)
17...520 V ac. (ph-ph)
45...65 Hz
0,5 % FS.
Altitude
Humidity
Storage temperature
10...50 ºC
2 000 m
95 % HR without condensation
-10...65 ºC
IP 53
Protection
Weight (only CIRe3) weight (with packaging)
0,677 kg
0,713 kg
Standard
ELECTRICAL SAFETY REGULATIONS: IEC 60664-1, IEC 61010-1, UL 94, VDE 110
ELECTROMAGNETIC EMISSIONS: IEC 61000-3-2, IEC 61000-3-3, IEC 61000-6-4, EN 55011, EN 55022
ELECTROMAGNETIC IMMUNITY: IEC 61000-6-2, IEC 61000-4-2, IEC 61000-4-3, IEC
61000-4-4, IEC 61000-4-5, IEC 61000-4-8, IEC 61000-6-1, IEC 61000-4-11, ENV 50141
M8-20
Portable power analyzer
M
.8
CIR-e
Q
Portable quality network analyzer
Measured parameters
Parámetro
Phase-neutral voltage
Phase-Phase voltage
Frequency
THD U
Fundamental U
Voltage harmonics (50º)
Quality %
Crest factor
Flicker WA
Flicker Pst
Unbalance
Asymmetry
Asymmetry
Over voltage
Hole voltage
Cut voltage
Símbolo
(unidad)
L1
V
L2 L3
Yes Yes Yes
III
V
Hz
Yes Yes Yes
Yes
Yes Yes Yes
Yes Yes Yes
Har
Yes Yes Yes
WA
Pst kd V
Ka V
Yes Yes Yes
Yes Yes Yes
Yes Yes Yes
Yes Yes Yes Yes
Yes Yes
Yes Yes
Máx./Min.
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Connections
Umbalanced three-phase system
References
Analyzer
CIR-e
Q kit 6 Voltage cable
Carring bag
Balanced single-phase system
Accesories
Dimensions
Magnetic fixing
Code
M85010
M86020
M89931
M8-21
M
.8
Portable power analyzer
Special clamps
High voltage clamps
PI-23
High voltage clamps
Features
}
Open clamps can be used to measure current in points where the power supply can not be interrupted
Application
}
PI-23
Maximum voltage
Maximum measurement current
Maximum conductor diameter
Voltage circuit
Battery
Frequency
Backlit
Digits
Accuracy
Build features
Degree of protection
Weight (without battery)
Ambient conditions
Operating temperature
Relative humidity
Vicat softening temperature
Standards
61010 Electrical safety
References
I max
400 A
U max
36 kV
∅ max
25
400 A 36 kV 25
6 m Pole (3 sections of 2 m)
Type
PI-23 + case (50 Hz)
PI-23 + case (60 Hz)
36 kV
400 A (2 scales)
25 mm
9 V, 6F22
50 Hz (60 Hz, on demand)
LCD
3
± 2 %
IP 50
290 g 360 g with receiver
0…+50 ºC
0…80 % RH
150-155 ºC
Code
M80132
M80132001
M89941
M8-22
Portable power analyzer
M
.8
Clamps with logger
CPL
Clamps with memory
Description
}
Current sensing clamps that measure and integrate the current in true root mean square.
}
Internal memory used to store mean values (128 kB)
}
Measurement in true root mean square
}
Maximum and minimum current values
}
Trigger option
}
Real-time clock to record events
}
PC connection to program and obtain data recorded
Features
Voltage circuit
Through an external power supply unit
Self-power supply
Frequency
Measurement range
Accuracy with external power supply
Memory
Type of memory
Safety
Standards
230 Vac (± 15 %)
I >15 % I n
50 ... 60 Hz
1 at 100% I n
1 % of the reading (± 2 digits
128 KB ( > 8000 records)
Linear
Category III 640 V (self-power supply), EN 61010
EN 60664, VDE 0110, UL 94, EN
60801, EN 6100, EN 61010-1
References
Includes memory with power supply, RS-232 interface and PowerVision software
M8-23
M
.8
Portable power analyzer
T-3V
Earth resistance meter
Description
}
Capable of measuring the earth voltage
}
The 2 mA measurement current can be used to make resistivity tests of the earth to trigger the earth circuit breakers of the circuit being tested
}
Battery operated
}
Self-disconnection. The timer is operated automatically after no control has been used for 3~6 minutes. The meter is in operation when the operation push-button and the timer activation button are pressed at the same time
}
Reading memory function
}
Open circuit indicator. The OFF LED indicates when the connection of the test bits is correct
}
Compact and light
}
Designed to comply with the IEC-1010 security standard (EN61010)
Features
Measurement system
Earth voltage
Earth resistivity
Earth voltage accuracy
Earth resistivity accuracy
Safety standards
Low battery indicator
Read memory indicator
Over-margin indication
Open circuit indicator
Timer (auto-disconnection)
Indicator
Power supply
Dimensions
Weight
Accessories
Connections
Type
T-3V
Code
M80410
Earthing resistance to earth with a constant current inverter
800 Hz, 2 mA approx.
0...200 V ac, 40...500 Hz
Scale and resolution
0 ~ 20
Ω ( 0.01Ω )
0 ~ 200
Ω ( 0.1Ω )
0 ~ 2000
Ω ( 1Ω )
± (1 % read. + 2 dig.)
± 0.1% _ or (when greater);
± (2 % read. + 2 dig.)
IEC-1010 (EN 61010)
The "B" symbol will appear on the display
The "DH" symbol will appear on the display
“1” on the most significant digit (MSD)
The operation indicator (2) will be turned off
When no control is operated, after 3 ~ 6 minutes
3 digit LCD (2000 records)
Six 1.5 V batteries (R6C)
W. 163 x H. 100 x D. 50 mm
Approx. 600 g (including batteries)
Testing bits (red – 15 m, yellow – 10 m, green – 5 m), auxiliary earthing rods, carrying case, instruction manual
M8-24
Portable power analyzer
M
.8
MEG-S
Insulation meter
Description
The MEG-S unit has a backlit LCD display and it is used to take insulation (M Ω ), continuity ( Ω ) and AC voltage readings.
}
Press a button for instantaneous operation. In addition, in the case of taking continuous readings of M Ω or Ω , the unit has a builtin timer with automatic disconnection after 3 to 5 minutes to save on the consumption of batteries
}
LED indicator (red) to check the insulation and continuity
}
Use of the high-performance and accuracy DC-DC converter
}
Carrying case
}
Specially designed to measure the insulating resistance of domestic electrical appliances, distribution of energy lines and installations
Type
MEG-S
Code
M80420
Features
Indicator
Insulation reading
Auto-range function
Test voltage
AC voltage measurement
Impedance
Continuity measurement
Over-margin indication
Timer
Non-disruptive voltage
Power supply
Dimensions
Weight
Accessories
Connections
3
1/2
digit LCD indicator with maximum reading of 1999
20 M_ ± 1.5 % read. ± 2 dig.
200 M_ ± 2.5 % read. ± 2 dig.
2000 M_ ± 5.0 % read. ± 3 dig.
(for Insulation Measurement)
250 V, 500 V, 1000 V DC ±10%
0 – 750 V ±1.5 % read. + 2 dig.
10 M
Ω
0 - 20
Ω ± 2 % read. ± 4 dig.
0 - 200
Ω ± 1.5 % read. ± 2 dig.
0 - 2 k
Ω ± 1.5 % read. ± 2 dig.
Short-circuit current 3 mA
Acoustic continuity indication under:
8
Ω scale of 20 Ω
10
Ω scale of 200 kΩ
40
Ω scale of 2 kΩ
“1” on the most significant digit (MSD)
Automatic disconnection after 3 minutes
In compliance with the IEC-1010 security requirements category III
Six 1.5 V batteries (R6C)
W. 163 x H. 100 x D. 52 mm
Approx. 430 g (including batteries)
Batteries (6)
Testing bits
Carrying case
Instruction manual
M8-25
M
.8
Portable power analyzer
CPM
Current sensing clamp - multimeter
Description
}
The CPM current sensing clamp offers the voltage, current, resistance and frequency measurement functions, with an acoustic continuity buzzer and diode test.
}
Three push-buttons are used to select the measurement hold (HOLD), maximum value
(MAX) and DC current measurement reset
(DCA ZERO) functions
}
The meter is powered with a 9 V battery.
Its design and double insulation make the
CPM a safe and robust instrument
Type
CPM
Code
M80430
Features
Indicator
Presentation functions Hold
MAX
Polarity
Over-margin
Zero
Low battery indicator
Reading rate
Power supply
Autonomy
Ambient conditions
Operating temperature
Storage temperature
Dimensions
Weight
Accessories
Reference conditions
DC Voltage
Scale
Accuracy
Input impedance
Overload protection
AC Voltage (50-500 Hz)
Scale
Accuracy
Input impedance
Overload protection
Resistance
Scales
Accuracy
Open circuit voltage
Overload protection
Frequency (Auto-range)
Scales
Accuracy
Sensitivity
Overload protection
Continuity
Acoustic warning
Overload protection
Diode test
Testing current
Accuracy
Open circuit voltage
Acoustic warning
Overload protection
DC Current
(Place the conductor in the centre of the piece)
Scales
Resolution
Accuracy
Overload protection
AC Current (40 Hz to 500 Hz)
(Place the conductor in the centre of the piece)
Scales
Resolution
Accuracy
Overload protection
3 1/2 digit LCD indicator with maximum reading of 1999
Measurement retention
Retention of the maximum measurement value
Automatic, positive by default and negative polarity indicator (-)
(OL) or (-OL) will be shown on the display
Automatic
“ “ will be displayed when the voltage of the battery is under the normal operating levels
2.5 readings per second, nominal
9 V Battery, IEC 6F22
200 standard hours, with carbon-zinc battery
0 °C to 40 °C (RH 0-70%)
20 °C to 60 °C, (RH 0-80%) with the battery removed
250 (W) x 100 (H) x 46 mm. (D)
380 g, including battery
A pair of test bits. Carrying case
Environmental conditions: 23 °C ± 5 °C, RH < 75%
600 V
± (0.5% read. + 1 digit)
10 M
Ω
600 V dc or ac. rms
200 V, 600 V
± (1.2% read. + 4 digits)
10 M
Ω
600 V dc or ac. rms
2 k
Ω, 200 kΩ
± (1.2% read. + 1 digit)
0.3 V dc
600 V dc or ac rms
2 kHz, 20 kHz
± 0.1% read. + 3 digits
80 V rms minimum
600 V dc or ac rms
Lower than 30
Ω in the 2 kΩ
600 V dc or ac rms
1.0 mA ± 0.6 mA
± (6.0% read. + 3 digits)
3,0 V dc standard
< 30 mV
600 V dc or ac rms
200 A, 700 A
100 mA
± (1.5% read. + 5 digits)
700 A dc Max. during one minute
200 A, 700 A
100 mA
± (1.5% read. + 5 digits) 50 to 60Hz
±(3.5% read. + 5 digits) 40 to 500 Hz
700 A dc Max. during 1 minute
M8-26
Portable power analyzer
M
.8
CDB
Description
}
Designed to take readings in single or three-phase installations
}
Measurement of amperage with voltages per phase of 190 to 260 V
}
Inspection of all sorts of residual current devices
}
Powered with batteries or accumulators
}
Measurement of the voltage between the phase and earth UL-PE
}
Measurement of the voltage between the phase and neutral UL-N
}
Measurement of the voltage between the neutral and earth terminal UN-PE
}
Measurement of frequency
}
Measurement of the protection loop impedance RS
}
Measurement of the protection loop impedance RS, with no disconnection of the
RCD
}
Measurement of the trigger time tA of the
RCD with earth leakage intensity I_N, 5x
I_N and pulsed current
}
Checking the RCD with gradual incremental voltage, measurement of the operating intensity of the RCD I_ and measurement of the contact voltage UI_ when the RCD is disconnected
}
Measurement of the contact voltage
UI_N when passing the nominal operation intensity 0.45x I_N through earth with no synchronisation of the RCD, checking that the RCD is not disconnected
}
Cabling inspection (results are displayed in the form of symbols)
}
Optional backlit LCD display
}
The values read are automatically stored and then displayed on the display
Basic operating instructions
}
The instrument can be used at a room temperature of - 5° C to 40° C. Instruments stored during a long period of time at temperatures under 0ºC must be acclimatised during 2 hours prior to storage
}
The maximum relative humidity in air allowed is 80 % at 23° C
}
The instrument must not be exposed to aggressive gases and vapours that could cause oxidation, liquids and dust
}
The instrument can only take readings under reference conditions with no additional errors
}
The maximum resistance of the housing to heat is a maximum of 80º C
}
The instrument can not take readings when the ºC overheating symbol is displayed
}
The instrument can also be connected between phases during a maximum interval of 5 minutes
}
All units under the RCD (Capacitors, rotating machines, etc.) as well as the residual currents of circuits can have an impact on the readings
}
The voltage drops in batteries under the limits allowed is shown by the symbol that appears on the lower left corner of the screen
}
The correct battery polarity must be maintained when changing batteries (in accordance with the battery clamp symbols).
Used batteries will reduce the clarity of the display, even though this does not have an impact on the operation of the instrument.
Batteries can not be changed when the instrument is connected to the mains. The instrument must not be connected to the mains when the battery lid is damaged. The lid must be changed immediately
}
The two-wire adaptor can only be connected to the CDB instrument for measuring purposes, i.e., it can not be connected to the power supply
}
The CDB plug must be connected to the adaptor's output (when a two-wire adaptor is used) before it is connected to the mains or to the load being measured
Coding
M8-27
M
.8
Portable power analyzer
LXM
Luxmeter
M8-28
Type
LXM
MS-148
Alternating voltage detector
}
Measurement of ac, from 70 to 600 V ac, with no need to be in contact with the voltage
Coding
Type
MS-148
Code
M80440
Code
M80450
Features
Measurement ranges
Resolution
Accuracy
Temperature features
Response time
Light detector: Photodiode
Operating temp. / humidity
Storage temp. / humidity
Range Overload
Power supply
Battery working life
Dimensions
Weight
Accessories
0.00 to 39.99/399.9/3999/39990 lx
0.000 to 3.999/39.99/399.9/3999 fc automatic selection / range manual
0.01 lx ~ 10 lx ; 0.001 fc ~ 1 fc
±3% rdg ±5 digits
±0.1% / º C
0.5 sec.
Yes
0º C ~ 40º C (32 ºF ~ 104º F) , 0 ~ 80% HR
-10º C ~ 50º C (14ºF ~ 122º F) , 0 ~ 70% HR
“ ---- ” display one 9V battery ,006P or IEC 6F22 or NEDA 1604
Approx. 170 hours (Alkaline battery)
196 (L) x 54 (W) x 33 (H) mm
7.7 (L) x 2.1 (W) x 1.3 (H) inches
Approx. 180 gr
9V Battery, instruction manual
Portable power analyzer
AR5 / AR5-L Accessories
Charging power supply and interface ( RS-232)
Description
Includes:
}
80 - 250 V ac Power supply
}
Power supply cable
}
Cable to connect the power supply and the AR5 / AR5-L
}
Series cable (RS-232) to connect the power supply and PC
Code
Battery
Description
Replacement for the internal battery of the
AR5 / AR5-L analyzer
Code M89904
M
.8
Case for AR5 / AR5-L
Description
Code M89901
Carrying bag for AR5 / AR5-L
Description
Includes pockets for the following:
}
One AR5 or AR5-L analyzer
}
4 current sensing clamps (CP5, CP100,
CPR500, CPR1000, CP2000 / 200, CF-5 or any kit with flexible clamps)
}
Power supply and power supply / voltage measurement cables
}
Folder with the manuals of PowerVision and other programs
}
Accessories of the AR5 or AR5-L analyzer
Code M89905
M8-29
M
.8
Portable power analyzer
AR5 / AR5-L Accessories
Case for AR5-L clamps
Description
Case for AR5-L clamps
Code M89921
1000 L Case
(with protective foam, for CPR-1000 clamps of the
AR5-L analyzer )
Description
Includes pockets for the following:
}
One AR5 or AR5-L analyzer
}
4 CPR100 current sensing clampsPower supply and power supply / voltage measurement cables
M89923
2000 L Case
(with protective foam, for CPR-2000 /200 clamps of the
AR5-L analyzer)
Description
Includes pockets for the following:
}
One AR5 or AR5-L analyzer
}
4 CPR2000 / 200 current sensing clamps
}
Power supply and power supply / voltage measurement cables
Code M89924
C-FLEX Case
(with protective foam, for C-FLEX clamps of the
AR5 or AR5-L analyzer )
Code M8992F
M8-30
AR5 / AR5-L Accessories
Check Meter + optical reader
Description
Includes:
}
Check Meter Program for AR5-L (last version). The corresponding cartridges are included, such as the CheckMeter program for AR5-L and the co-processor.
}
Check Meter optical sensor (with the optic fibre cable to monitor meters and the communications and power supply cable that connects it to the AR5-L)
}
Program User Manual CheckMeter (including the explanation of how the sensor must be used)
Code M806C3
Power Vision
Description
}
AR5AR5-LCIRCUTOR
For more information, see M.9 Catalogue
Code
M90411
PC Communications cable
Description
}
RS-232 Series connection cable, with two DB9 connectors (male and female), with a length of 1.2 m. Used in AR5 and AR5-L analyzers to download the data stored in the
PC with the Power Vision Software.
Code M8991E
Portable power analyzer
M
.8
M8-31
M
.8
Portable power analyzer
AR5 / AR5-L Accessories
Adaptor cable (3 cables) AR5-L / AR5
Description
Code M89917
Adaptor cable (1 cable) AR5-L / AR5
Description
}
4-way female connector on one end and
3-pin male connector on the other end.
M89922
Adaptor cable (1 cable) AR5 / AR5-L
Description
}
3-way female connector on one end and
4-pin male connector on the other end, with phase colour.
Code M89932
Cable to connect the AR5 / AR5-L unit to the power supply
}
Cable to connect the power supply input and communications between the analyzer and power supply.
M8992C
M8-32
AR5 / AR5-L Accessories
Set of 4 voltage cables
Description
}
Set of 4 cables to connect the voltage inputs of the AR5 / AR5-L analyzer to an electric panel or sub-panel.
Code M89908
Crocodile clamp
(1 unit)
Description
}
Clamp that adapts to the voltage cable and can be connected to an electric panel or sub-panel to measure voltage.
Code M89909
C-80 Accessories
3 voltage cable replacement kit
Description
}
Set of 3 cables to connect the voltage inputs of the C-80 analyzer to an electric panel or sub-panel.
Code M89907
C-80 Case
Description
}
Case to carry the C-80 analyzer easily and safely.
M89931
Portable power analyzer
M
.8
M8-33
M
.8
Portable power analyzer
M8-34
advertisement
Related manuals
advertisement