Assembly Instructions:
To purchase parts or accessories, please contact us at
www.spectrumfurniture.com
1-800-235-1262
Thank you for choosing Spectrum products!
(20) 0101382
#14 x 7/8" PHSM Screws
Flex Flip Tables
Before you begin, please make sure all parts and proper quantities are
included. Any parts damaged during shipment must be reported within
15 days of receipt. To report information regarding damages or if you
have any questions, please call 1-800-235-1262.
24"D
#37310 - 48"W
#37312 - 60"W
#37314 - 72"W
30"D
#37311 - 48"W
#37313 - 60"W
#37315 - 72"W
Tools Required:
Phillips screwdriver
Hex wrench (included with legs)
1/2" wrench
1. Attach Leg Mechanisms
A. Place worksurface face-down onto a non-abrasive surface.
B. Orient the leg mechanisms and release handle as shown and align with the
worksurface mounting holes. Figure 1A.
C. Attach the leg mechanisms and release handle to the worksurface using
(20) #14 x 7/8" PHSM screws and tighten securely.
D. Secure the cables to the worksurface with the included clips,
(4) #8 x 3/4" PHSM screws, and pre-drilled holes. Figure 1B.
Attach leg mechanisms to
worksurface with
#14 x 7/8" PHSM screws
Cables
Leg Mechanism
Leg Mechanism
Release handle
Secure cables with (4) PHSM
screws & cable clips (included
with table legs)
Mounting
holes
Cable
Worksurface
Cable Clip
Figure 1A
Figure 1B
0108517R2 Page 1 of 3
2. Attach Legs
A.
B.
C.
D.
Set a leg on each leg mechanism. Figure 2.
Attach each leg with the included hex screws (4 per leg) and hex wrench.
Tighten screws securely.
Be sure swivel wheels are tightened securely.
(Tighten with 1/2" wrench if necessary.)
E. Carefully tip the table upright- this will require two people.
Leg
Leg
Leg
Mechanism
Hex screws (4 req'd)
Spring clip button on each
leg provides 9" of total height
adjustment in 1" increments
Figure 2
Leg Mechanism
Figure 3A
Figure 3B
Figure 3C
3. Table Operation
● To adjust the worksurface height, press the spring clip button on one leg and raise or lower the worksurface and upper leg assembly (slightly
twisting then sliding the leg after the button has been pressed will help keep it retracted until its aligned with the new hole.) Figure 3A. Align the
spring clip button with one of the adjustment holes to lock the leg into the new position. Repeat this procedure on the other leg while making
sure to use the same hole position on both legs.
● To flip-up the worksurface, pull the release lever while lifting up the edge of the worksurface until it locks into place. Figure 3B. To lower, pull
the release lever while lowering the worksurface-be sure it locks into place. Multiple desks can be “nested” together next to a wall to save space.
Figure 3C.
0108517R2 Page 2 of 3
Warranty
WE WILL MAKE IT RIGHT FOR YOU!
Spectrum is committed to provide complete customer satisfaction. Each of our products are manufactured from the best materials available and
each product is stringently monitored throughout the production process through our P.A.C.E. program (Product Assurance to meet Customer
Expectations). Our Customer Service Help Line 1-800-235-1262 is ready to provide immediate attention to any questions, comments or
concerns. We are available to answer your calls Monday through Friday from 7 am to 5 pm CST, excluding observed holidays. In addition your
product comments or concerns are welcome via e-mail at: [email protected].
Warranty Statement
We guarantee all Spectrum products to be free of all defects in materials and workmanship, for the original owner, for a period of ten years. Any
item deemed defective by Spectrum or the original manufacturer, under normal use conditions, will be repaired or replaced at Spectrum’s
discretion. This warranty applies to all products manufactured and distributed by Spectrum except the products
listed below.
Items that have a varying warranty include, but are not limited to, the following:
• Adjustable Crank/Electric Desk Legs (1 yr)
• Flat Panel Desk Gas Cylinders (1 yr)
• Upholstered Soft-Goods (5 yrs)
• Adjustable Height & Stacking Chair Parts – including frames, gas cylinders, wood and plastic parts, and control handles (7 yrs)
• Adjustable Height & Stacking Chair Casters (2 yrs)
• Chair Upholstery & Textiles (2 yrs of normal use of Soft Goods, Adjustable Height, Stacking, Wood and Metal Chairs)
• Chair Upholstery - Graded-In Fabrics and C.O.M (no warranty)
• Height Adjustable Columns and Lifts (1 yr)
• General Use Casters (1 yr)
• Electrical – Electri-Pak, Power Communication Modules, and special order ECA electrical items (1 yr)
• Electrical - Power Strips & Electrical Timers (1 yr)
• Electrical Surge Suppressors (lifetime)
• Electrical - Retractable Power Cords (1 yr)
• Keyboard/Mouse Trays (1 yr)
• Flat Panel Monitor Arm – General Parts (5 yrs)
• Flat Panel Monitor Arm – Gas Cylinders (2 yrs)
• CRT Monitor Arm (1 yr)
Warranty
its iintended
multiple-shift
accident,
W
t is
i void
id if product
d t iis nott used
d ffor it
t d d purpose or subjected
bj t d tto an unusuall application,
li ti
lti l hift use, alteration,
lt ti
id t
abuse or abnormal wear and tear. Representations of colors on-line and in printed materials are meant to be a close reference to the actual
colors but not an exact match. Slight variations in color and texture of wood stains, powder coating, laminates, fabrics and other materials are
normal in different manufacturing lots; as such these variations are not considered defects.
DESIGNED FOR INDOOR USE ONLY – Unless specifically stated in the product specifications, Spectrum’s products have been designed and
constructed for indoor use only. Moving or using outdoors, or on excessively rough surfaces, may cause damage to the products and will void the
warranty. If an outdoor application is desired please contact us to discuss potential custom design solutions.
The warranty, as stated above, supersedes any previous warranties and is effective as of 9/1/2010
0108517R2 Page 3 of 3
">
