advertisement
Instrument
Components: x4
M8 Nyloc Nut x2
M6x20 Security Screw x4
2 Part Cover
Cap x1
M6 Saddle Strap
Metric
Conversion:
250mm/ 10”
300mm/ 12”
450mm/ 18”
700mm/ 28”
850mm/ 33”
1.5m/ 59”
Ground Fixed
Cavatina
Page 1 of 3
Installation Instructions
(1.3)
(1.1) (1.1)
(1.2)
1. Attach the steel legs to the base of the instrument with the M8 Nyloc Nuts and 2 part security caps. (1.1) (See
Assembly Guide)
2. Attach Ground Fixing posts to legs(1.2) (See Ground Fix
Post Installation Sheet)
3.Excavate 1 hole for the
Steel legs 250mm diameter by 300-450mm deep depending on Key stage, in desired location upon decision from customer.
4. Locate (lower) leg into holes making sure they are vertical and level prior to concreting in place.
5. Once happy with location of the Instrument, fill holes using rapid hardening concrete. Be sure to compact concrete around legs and leave to dry according to manufactures guidelines.
1.5m
KS1 – 700mm
KS2 – 850mm
1.5m
Install Instrument with 1.5m free space
(from widest point) around it.
Ground Surface
Weight of heaviest part 11kg (Cavatina)
Pair Small Red
Beaters X1
Ground Fix
Components:
6. Attach the 1 pair of beater to the saddle strap on the leg.
(1.3)
KS2 - 300mm
KS1 - 450mm x2
M10x200 Bolt M10 Nut x4
Spares available from percussionplay.com or from your local distributor
19.5 Kg
BS EN 1176
Assembly Guide PPSANS
Tools: x1
TX 30 Driver Bit x1
TX 40 Driver Bit
Ground Fixed
Cavatina
Page 2 of 3
Instrument
Components: x4
M8 Nyloc Nut x2
M6x20 Security Screw x4
2 Part Cover
Cap x1
M6 Saddle Strap
M6 Saddle Strap
Thread Lock Solution
Required (Not Supplied)
BS EN 1176
(1.1)
Thread Lock Solution
Required (Not Supplied)
COMPONENTS LIST:
2 Part Cover Cap X4
M8 Nyloc nut X4
M10 Nut X4
M10x200 Threaded Bar X2
Saddle Strap X1
M6x20 Pin torx X2
PPCAVA FRONT
Pair Small Red
Beaters X1
Ground Fix
Components: x2
M10x200 Bolt M10 Nut x4
PPCAVA SIDE
Spares available from percussionplay.com or from your local distributor
19.5 Kg
Ground Fixed
Cavatina
Page 3 of 3
Ground Fix Post Installation
1 2
Components: x2
M10x200 Bolt
M10 Nut x4
Metric Conversion:
50mm/ 2”
250mm/ 10”
300mm/ 12”
350mm/ 14”
400mm/ 16”
450mm/ 18”
3
Insert M10x 200 Threaded Fix M10x 200 Threaded bar in place using M10
Nuts
Foundations should not present a hazard. These foundations are recommended as a guide, for more information on foundation details for various surface see Part 7 of BS EN 1176.
4 5
Excavate a hole with a
250mm diameter tapering down to 350mm diameter and 350mm depth
250
Compact base of hole with
50mm of aggregate.
Lower ground Fix post attached of instrument into hole (check instrument straight and level before filling with concrete)
300mm min depth
Concrete
Fill hole with fast drying concrete to manufacturers specifications.
Aggregate
350
BS EN 1176
advertisement
Related manuals
advertisement