advertisement
Surface Fixed
Babel Drum
Page 1 of 2
Instrument
Components: x3
M8x25mm Pin Torx
Metric Conversion:
850mm/ 33
15/32
”
855mm/ 33 21/32 ”
1.5m/ 59”
BS EN 1176
Installation Instructions
1. Unpack ground fixing legs
3no.
2. Lay packaging out on floor or assemble on non-abrasive surface to prevent marking of polished stainless steel.
3. Align holes on legs to holes on surface fixing(opposite end to polished domes) and secure in place using 3no.
M10 x 30mm Screws provided
Tools required TX 45 Driver
Bit)
4. Invert assembled frame so domed ends face upwards.
5. Place 8mm Hex Key supplied into hole in leg and lock into internal bolt.
6. Remove Black Cap opposite side of leg and keeping Hex Key in place, slide black polyurethane damper over bolt until flush with end of bolt. Repeat for other 2 legs
7. Unpack babel drum leaving black film in place to protect.
Weight of heaviest part 17.5kg
(Large Babel Drum)
Weight of heaviest part 13.4kg
(Small Babel Drum)
8. Align holes in side of babel drum with bolts on legs.
Played with hands
Ground Fix
Components: x3
M10x30 Security Screw x4
2 Part Cover Cap
9. Using 8mm Hex Key screw bolts into drum to secure in place.
Use thread locking solution
All hole locations are laser cut for accuracy to ensure holes in drum align perfectly with legs.
10. Using TX40 driver provided secure M8 x 25mm security bolts into external holes in legs 3no. Use thread lock solution
11.Locate Babel Drum in desired location and mark holes to fix to desired surface.
850mm from Plate
CAUTION: Drum surface can get hot in direct sunlight, if possible install in shaded areas.
1.5m
1.5m
Install
Instrument with 1.5m free space (from widest point) around it.
12. Fix to Surface using recommended ground anchors (Ground Anchors are not supplied)
13. Make sure all fixings are covered and secure using cover caps provided
855mm from Plate
Large 8 note
Ground Surface
Small 6 note
Ground Anchors not supplied
Spares available from percussionplay.com or from your local distributor
22 Kg
13.4 Kg
Surface Fixed
Babel Drum
Page 2 of 2
Assembly Guide PPBDL-S
Thread Lock Solution
Required
Tools: x1
TX 45 Driver Bit Hex T Key x1 x1
TX 40 Driver Bit
Instrument
Components: x3
M8x25mm Pin Torx
1 2 3
Thread Lock Solution
Required
BS EN 1176
Locate the Surface fix
Plate into the leg of the instrument.
Played with hands
Ground Fix
Components: x3
M10x30 Security Screw
Fix instrument to Surface fix plate using M10
Screws and use thread locking solution to prevent fixings working loose.
x4
2 Part Cover Cap
Fix Surface Plate to the ground surface Ground
Anchors Not provided cover fixings with caps provided
Ground Anchors not supplied
Spares available from percussionplay.com or from your local distributor
22 Kg
13.4 Kg
Surface Fixed
Bell Lyre
Page 1 of 2
Instrument
Components: x4
M6x20 Security Screw x2
M6 Saddle Strap
Metric Conversion:
1.5m/ 59”
1525mm/ 60”
BS EN 1176
Installation Instructions
1. Attach Surface Fixing posts to legs(See Surface Fix Post
Installation Sheet)
1.5m
1.5m
Install Instrument with 1m free space
(from widest point) around it.
2.Locate Plate in desired location and mark holes to fix to desired surface.
1525mm
3. Fix Surface Plate to level surface using Coachscrews,
Rawlbolts, chemical anchors or similar as deemed appropriate by Installer.
(It is your responsibility to ensure that the existing surface is suitable to receive the appropriate fixing)
Ground Surface
4. Make sure all fixings are covered and secure using cover caps provided
CAUTION: Bell
Lyre surface can get hot in direct sunlight, if possible install in shaded areas.
Weight of heaviest part 14.4kg
(Bell Lyre)
Pair Small Red
Beaters X1
Ground Fix
Components: x4
2 Part Cover Cap x1 x1
M10x70 Security Screw M10 Barrel Nut
Ground Anchors not supplied
Spares available from percussionplay.com or from your local distributor
23.5 Kg
Surface Fix Post Installation
Surface Fixed
Bell Lyre
Page 2 of 2
1 2
(1.1)
Components: x1
M10 Barrel Nut x1
M10x70 Security Screw x4
2 Part Cover Cap
Thread Lock Solution
Required (Not Supplied)
BS EN 1176
Locate the Surface fix
Plate into the leg of the instrument.
3
Tools: x2
TX 45 Driver Bit
Thread Lock Solution
Required (Not Supplied)
Fix instrument to Surface fix plate using M10 bolt and Barrel Nut and use thread locking solution to prevent fixings working loose.
Fix Surface Plate to the ground surface Ground
Anchors Not provided cover fixings with caps provided
Installation Instructions
Surface Fixed
Handpipes
Page 1 of 3
1. Handpipes will arrive on site assembled, Surface
Fixings will need to be installed (1.1) (See Assembly
Guide) 1.5m
2. Attach Surface Fixing posts to legs (See Surface Fix Post
Installation Sheet)
1.5m
Install Instrument with 1.5m free space
(from widest point) around it.
Instrument
Components:
Instrument assembled
Metric
Conversion:
250mm/ 10”
400mm/ 16”
905mm/ 35”
1.5m/ 59”
BS EN 1176
(1.1)
3.Locate Instrument in desired location and mark holes to fix to desired surface.
905m m
4. Fix to Surface using recommended ground anchors not supplied
Ground Surface
5. Make sure all fixings are covered and secure using cover caps provided
Weight of heaviest part 20kg (Handpipes)
Played with hands
Surface Fix
Components: x2 x2 x8
M10x50 Security Screw M10 Barrel Nut 2 Part Cover Cap
Ground Anchors not supplied
Spares available from percussionplay.com or from your local distributor
25 Kg
COMPONENTS LIST:
M10 Nut X8
M10x200 Threaded Bar X4
M10x60mm Security Screw X2
M10 Barrel Nut X2
Surface Fixed
Handpipes
Page 2 of 3
Instrument
Components:
Instrument assembled
Assembly Guide PPHAND
498
(1.1)
COMPONENTS LIST:
M10 Barrel Nut X2
Thread Lock Solution
Required (Not Supplied)
BS EN 1176
Played with hands
Surface Fix
Components: x2 x2 x8
M10x50 Security Screw M10 Barrel Nut 2 Part Cover Cap
Ground Anchors not supplied
Spares available from percussionplay.com or from your local distributor
25 Kg
Surface Fix Post Installation
Tools: x2
TX 45 Driver Bit
Components: x2
M10 Barrel Nut x2
M10x50 Security Screw x8
2 Part Cover Cap
Thread Lock Solution
Required (Not Supplied)
Metric
Conversion:
50mm/ 2”
250mm/ 10”
350mm/ 14”
400mm/ 16”
450mm/ 18”
BS EN 1176
Surface Fixed
Handpipes
Page 3 of 3
1 2 3
(1.1)
Thread Lock Solution
Required (Not Supplied)
Locate the Surface fix
Plate into the leg of the instrument.
Repeat Parts 1-3 for both legs
Fix instrument to Surface fix plate using M10 bolt and Barrel Nut and use thread locking solution to prevent fixings working loose.
Fix Surface Plate to the ground surface Ground
Anchors Not provided cover fixings with caps provided
Surface Fixed
Flat Pack Harmony
Page 1 of 2
Instrument
Components:
M10 Nut x6
M6x20 Security Screw x3
M6 Saddle Strap
Metric Conversion:
178mm/ 7”
250mm/ 10”
400mm/ 16”
1385mm/ 55”
1.5m/ 59”
BS EN 1176
Installation Instructions
1. Unpack frame 3no.
2. Lay packaging out on floor or assemble on non-abrasive surface to prevent marking of polished stainless steel.
3. Align holes on legs
(opposite end to polished domes) and secure in place using 3no. M10 x 200mm threaded bar and 6no. M10 nuts provided
Tools required 2no. 17mm metric spanner/wrench ( 11 inch or alternatively using adjustable wrench)
/
16
8. Fix Surface Plate to level surface using Coachscrews,
Rawlbolts, chemical anchors or similar as deemed appropriate by Installer.
(It is your responsibility to ensure that the existing surface is suitable to receive the appropriate fixing)
9. Make sure all fixings are covered and secure using cover caps provided
1385mm
4. Invert assembled frame so domed ends face upwards.
5. Insert M8x60mm Security screws into pre drilled holes in frame using TX40 bit.
6. Attach Notes and Surface
Plate to Harmony Frame. (See
Assembly Guide Sheet)
7.Locate Harmony in desired location and mark holes to fix to desired surface.
Weight of heaviest part 16kg (Harmony Frame)
Pair Small Red
Beaters X1
Surface Fix
Components: x2
M8x60 Security Screw x3 x4
M8x25 Security Screw 2 Part Cover Cap
Ground
Anchors not supplied
1.5m
1.5m
Install Instrument with 1.5m free space
(from widest point) around it.
CAUTION:
Harmony surface can get hot in direct sunlight, if possible install in shaded areas.
Ground Surface
Spares available from percussionplay.com or from your local distributor
20 Kg
Assembly Guide PPHARM
Tools: x1
TX 30 Driver Bit x1
TX 40 Driver Bit
Thread Lock Solution
Required
Surface Fixed
Harmony Flat Pack
Page 2 of 2
Instrument
Components: x6
M6x20 Security Screw x3
M6 Saddle Strap
Thread Lock Solution
Required
BS EN 1176
Thread Lock Solution
Required
COMPONENTS LIST:
Saddle Strap X3
M6x20 Pin torx X6
M8x60 Pin torx X2
M8x25 Pin torx X3
2 Part Cover Cap X8
Locate the Surface fix
Plate into the leg of the instrument.
Pair Small Red
Beaters X1
Fix instrument to Surface fix plate using M8x25
Screws and use thread locking solution to prevent fixings working loose.
Fix Surface Plate to the ground surface Ground
Anchors Not provided cover fixings with caps provided
Surface Fix
Components: x2
M8x60 Security Screw x3 x4
M8x25 Security Screw 2 Part Cover Cap
Ground
Anchors not supplied
CAUTION:
Harmony surface can get hot in direct sunlight, if possible install in shaded areas.
Spares available from percussionplay.com or from your local distributor
20 Kg
Surface Fixed
Tubular Bells
Page 1 of 4
Instrument
Components:
Tubular Bells are preassembled
BS EN 1176
Installation Instructions
Tubular Bells will arrive on site pre assembled
1.1 1.2
1.Locate Base in desired location before attaching the bells. Fix lower sections to surface using pre drilled holes provided. (Surface Anchors
Not supplied) Recommended
M10 Female Rawl Bolts or chemical anchors
2. Assemble Upper 3 Base sections using M8 x 16 mm
CSK screws provided (1.1)
3. Using the M10x 40 screw and Barrel Nuts to attach each of the 9 legs to the base
(1.2)
Ground Surface
4. Make sure that all fixings are tightly secured and thread locking solution used if required.
Weight of heaviest part 30kg (ALU Base)
Pair Large Red
Beaters X1
Surface Fix
Components: x9
M10x40 Security Screw x9
M10 Barrel Nut x34
M8x16 CSK Security Screw
Spares available from percussionplay.com or from your local distributor
90 Kg
Surface Fixed
Tubular Bells
Page 2 of 4
Assembly Guide TBEL SF
Instrument
Components:
Tubular Bells
Are Preassembled
COMPONENTS LIST:
M10 Barrel Nut Pin torx X9
M8x16 CSK Screw X34
M10x40 Pin torx X9
Tools: x1
TX 40 Driver Bit x2
TX 45 Driver Bit
BS EN 1176
Pair Large Red
Beaters X1
Surface Fix
Components: x9
M10x40 Security Screw x9
M10 Barrel Nut x34
M10x16 CSK Security Screw
Spares available from percussionplay.com or from your local distributor
90 Kg
Surface Fixed
Tubular Bells
Page 3 of 4
Assembly Guide TBEL SF
Tools: x1
TX 40 Driver Bit x2
TX 45 Driver Bit
Instrument
Components:
Tubular Bells
Are Preassembled
BS EN 1176
Mount this section of each base to the deck Deck Anchors Not provided using pre drilled holes
Insert instrument plates with stanchions and attach with CSK
M8x16mm Screws provided
Pair Large Red
Beaters X1
Surface Fix
Components: x9
M10x40 Security Screw x9
M10 Barrel Nut x34
M8x16 CSK Security Screw
Spares available from percussionplay.com or from your local distributor
90 Kg
Surface Fixed
Tubular Bells
Page 4 of 4
Assembly Guide TBEL SF
Tools: x1
TX 40 Driver Bit x2
TX 45 Driver Bit
Instrument
Components:
Tubular Bells
Are Preassembled
Join the upper and lower base sections with CSK M8x16mm Screws provided
Lower Instrument over the stanchions and attach with fixings provided (see surface fix installation instructions)
Pair Large Red
Beaters X1
Surface Fix
Components: x9
M10x40 Security Screw x9
M10 Barrel Nut x34
M8x16 CSK Security Screw
Spares available from percussionplay.com or from your local distributor
90 Kg
BS EN 1176
Surface Fixed
Tubular Bells
Page 1 of 2
Installation Instructions
1. Attach Surface Fixing plates to each of the 9 legs(1.2)
1.5m
2.Locate each chime in desired location and mark holes to fix to desired surface.
Install Instrument with 1.5m free space
(from widest point) around it.
2207
Instrument
Components:
Tubular Bells are preassembled
Metric Conversion:
250mm/ 10”
400mm/ 16”
600mm/ 24”
1.5m/ 59”
2207mm/ 98”
BS EN 1176
1.2
3. Fix Surface Plate to level surface using Coachscrews,
Rawlbolts, chemical anchors or similar as deemed appropriate by Installer.
(It is your responsibility to ensure that the existing surface is suitable to receive the appropriate fixing)
4. Make sure all fixings are covered and secure using cover caps provided
Weight of heaviest part 10kg (XXL Bell)
Pair Large Red
Beaters X1
Surface Fix
Components: x9
M10x40 Security Screw x9
M10 Barrel Nut x36
2 Part Cover Cap
1.5m
1.5m
Ground
Surface
Spares available from percussionplay.com or from your local distributor
59 Kg
Surface Fix Plate Installation
Surface Fixed
Tubular Bells
Page 2 of 2
1
Components: x9
M10 Barrel Nut x9
M10x40 Security Screw x8
2 Part Cover Cap
2 3
(1.1) (1.1)
Thread Lock Solution
Required (Not Supplied)
Locate the Surface fix
Plate into the leg of the instrument.
Repeat Parts 1-3 for all 9 legs
Fix instrument to Surface fix plate using M10 bolt and Barrel Nut and use thread locking solution to prevent fixings working loose.
Fix Surface Plate to the ground surface Ground
Anchors Not provided cover fixings with caps provided
BS EN 1176
advertisement