REACT Parasol Zenith
Modbus settings / Modbus-inställningar
Modbus settings for REACT Parasol Zenith with Belimo actuator
Modbus-inställningar för REACT Parasol Zenith med ställdon Belimo
20220810
REACT Parasol Zentih
Transfer protocol
Överföringsprotokoll
Protocol:
Modbus RTU
Protokoll:
Modbus RTU
Number of nodes
Max.32 (without repeater)
Antal noder max.
32
Baud rates:
9600, 19200, 38400, 76800, 115200
Kommunikationshastighet:
9600, 19200, 38400, 76800, 115200
Bit sequence:
LSB
Bitsekvens:
LSB
Transmission formats:
1-8-N-2, 1-8-N-1, 1-8-E-1, 1-8-O-1
Bitformat:
1-8-N-2, 1-8-N-1, 1-8-E-1, 1-8-O-1
Terminating resistor:
120 Ohm (extern)
Termineringsmotstånd:
120 Ohm (extern)
Response time:
≤ 10 ms + delay
Svarstid:
≤ 10 ms + fördröjning
Standard
communication parameter:
1 Start bit
Standard
kommunikationsparameter:
1 startbit
Communication setting: 14
19200 baud
Kommunikationsinställning: 14
8 Data bits
19200 baud
8 databitar
1 Stop bit
1 stoppbit
Even parity
Jämn paritet
Delay 0 ms
Fördröjning 0 ms
The values for communication speed, parity, stop bits and delay are changeable.
Värdena för kommunikationshastighet, paritet, stoppbitar och fördröjning är
ändringsbara.
Modbus Register Overview
Modbus Register Översikt
Operation
Operation
No.
Address
Access
Nr.
Adress
1
0
Setpoint [%]
R/W
1
0
Börvärde [%]
R/W
2
1
Override control
R/W
2
1
Tvångsstyrning
R/W
3
2
Command
R/W
3
2
Kontroll
R/W
4
3
Actuator type
R
4
3
Ställdonstyp
R
5
4
Relative position [%]
R
5
4
Relativ position [%]
R
5
Absolut position [°] [mm]
R
Register
Register
R/W
6
5
Absolute position [°] [mm]
R
6
7
6
Relative volumetric flow [%]
R
7
6
Relativt volumetriskt flöde [%]
R
8
7
Absolute volumetric flow [m³/h]
R
8
7
Absolut volumetriskt flöde [m³/h]
R
9
8
Sensor value 1 [mV] [–]
R
9
8
Sensor värde 1 [mV] [–]
R
10
9
–
–
10
9
–
11
10
10
12
11
Absolute volumetric flow
in unit selected
11
12
11
13
12
Setpoint analog [%]
13
12
LowWord
HighWord
R
R
–
Absolut flöde i vald enhet
LowWord
HighWord
Börvärde analogt [%]
R
R
Service
Service
2
x
No.
Address
Access
Nr.
Adress
100
99
Bus termination
R
100
99
Busterminering
R
R
R
Register
Register
101
100
Series number 1st part
101
100
Serienummer 1:a delen
102
101
Series number 2nd part
102
101
Serienummer 2:a delen
103
102
Series number 4th part
103
102
Serienummer 4:e delen
R/W
104
103
Firmware version
R
104
103
Firmware version
105
104
Malfunction and service information
R
105
104
Fel och serviceinfo
R
106
105
Min [%]
R/W
106
105
Min [%]
R/W
R
107
106
Max [%]
R/W
107
106
Max [%]
R/W
108
107
Sensor type 1
R/W
108
107
Sensor typ 1
R/W
109
108
Bus fail position
R/W
109
108
Bus fel position
R/W
R/W
110
109
Kommunikationsövervakning
R/W
110
109
Communication Watchdog
111
110
Nominal volumetric flow [m³/h]
R
111
110
Nominellt flöde [m³/h]
R
112
111
–
–
112
111
–
–
113
112
114
113
Nominal volumetric flow in
unit selected
LowWord
HighWord
R
113
112
114
113
Nominellt flöde i vald
enhet
LowWord
HighWord
R
115
114
–
–
115
114
–
116
115
–
–
116
115
–
117
116
Control Mode
R/W
117
116
Styrsignal läge
R/W
118
117
Unit Selection Flow
R/W
118
117
Enhetsval flöde
R/W
119
118
Setpoint source
R/W
119
118
Börvärdeskälla
R/W
Swegon reserves the right to alter specifications
20220810
–
–
REACT Parasol Zenith
Modbus Register Description
No.
Address
Description Comment
Beskrivning (SE)
Range Enumeration
1
Unit
Scaling
Access
0
Setpoint
Setpoint for actuator between
Min (Register No. 106) and Max
(No. 107)
Börvärde
Börvärde för ställdonet
mellan min och max
0…10‘000
Default: 0
%
0.01
R/W
2
1
Override Control
Override setpoint with defined
values
Tvångsstyrning
Tvångsstyr börvärdet
med fördefinierade
värden
0: None
1: Open
2: Close
3: Min
4: Mid
5: Max
Default: None(0)
–
–
R/W
3
2
Command
Initiation of actuator functions for
service and test After command is
sent, register returns to None(0)
With Reset(4) all Malfunction and
Service Information (Register No.
105) Information can be reset.
Kontroll
Initiering av ställdonets
funktion
0: None
1: Adaption
2: Test
3: Sync
4: Reset
Default: None(0)
–
–
R/W
4
3
Actuator Type
Ställdonstyp
0: Actuator not connected 1:
Air / Water
2: VAV / EPIV
3: Fire
4: Energy Valve
5: 6way EPIV
–
–
R
%
0.01
R
"°
mm
1
1
R
%
0.01
R
5
4
Relative Position
Relativ position
0...10‘000
6
5
Absolute Position
The unit depends on the device:
[°] for actuators with rotary
movement
[mm] for actuators with linear
movement
Absolut position
0...max angle / stroke
7
6
Relative volumetric flow
Relative volumetric flow of Vnom
Relativt flöde
0...10‘000
8
7
Absolut volumetric flow
Absolut flöde
0...Vnom
m³/h Pa
1
R
9
8
Sensor 1 Value
Current value of sensor 1, depending on the setting of the Sensor
1 Type (Register No. 108)
[mV] if Sensor 1 Type (Register No.
108) is Active(1)
[0 / 1] if Sensor 1 Type (Register
No. 108) is Switch(4)
Sensor 1 värde
Strömvärde från sensor
1, beroende på sensorinställning
0...65‘535
mV 0 / 1
1
R
10
9
–
11
10
Absolute volumetric flow
Absolute flow in unit selected (Register No. 118) LowWord Lower
16 bit of 32 bit value
Absolut flöde, lågt byte
12
11
Absolute volumetric flow
Absolute flow in unit selected (Register No. 118) HighWord Upper
16 bit of 32 bit value
Absolut flöde, högt
byte
13
12
Setpoint Analog
Shows the setoint in % if actuator
is control by analog signal
Börvärde analogt
20220810
–
–
–
–
–
UnitSel
0.001
R
%
0.01
R
0...10‘000
Swegon reserves the right to alter specifications
3
REACT Parasol Zentih
Modbus Register Description
No.
Address
Description Comment
Beskrivning (SE)
100
99
Bus Termination
Indicates if bus termination (120 Ω) is enabled
Bus termination can be set with the configuration
tools
Busterminering
101
100
Series Number 1st part
Each device has an unambiguous series number,
which is either impressed on or glued to the
housing
The series number consists of 4 segments,
although only parts 1, 2 and 4 are displayed on
Modus
Example: 00839-31324-064-008
1st part: 00839
2nd part: 31324
4th part: 008
102
101
Range Enumeration
Unit
Scaling
Access
0: inactive
1: active
Default: inactive(0)
–
–
R/W
Indikerar om
Bus-terminering
är aktiv
–
–
–
R
Series Number 2nd part
Serienummer
–
–
–
R
103
102
Series Number 4th part
Serienummer
–
–
–
R
104
103
Firmware Version
Firmware version of communication module Example: 302, Version 3.02
Firmware
version
–
–
–
R
105
104
Malfunction and Service Information
Value is bit-coded. More than one bit can be set
to 1
All bits not montioned in the enumeration are
not used for this actuator range Mechanical travel
increased: The actuator has been moved outside
the adapted working range
Actuator cannot move: Mechanical overload e.g.
blocked actuator, etc. Internal activity: Actuator
performs a test run, adaption, etc.
Gear disengaged: The gear disengaged button is
pressed
Bus Watchdog triggered: Timeout for the Bus
Watchdog expired
Fel och serviceinformation,
Bitkodat värde
Bit1:
Bit2:
Bit8:
Bit9:
Bit10:
–
–
R
106
105
Vmin
Min has to be ≤ Max
Vmin
0...Vmax
Default: 0
%
0.01
R/W
107
106
Vmax
Max has to be ≥ Min and > 20%
Vmax
Vmin...10‘000
Default: 10‘000
%
0.01
R/W
108
107
Sensor 1 Type
If Setpoint Source (Register 119) is analog (Hybrid
mode) the sensor type 1 can be set to Active(1) in
order to see the Setpoint Analog in mV
Sensor 1 typ
0: None
1: Active / Hybrid
2: –
3: –
4: Switch
Default: None(0)
–
–
R/W
109
108
Bus Fail Position
Modbus communication is not monitored as standard. In the event of a breakdown in communication, the actuator retains the current setpoint The
bus implementation tracks the Modbus communication. If neither the Setpoint (Register No. 1) nor
the Override Control (Register No. 2) is renewed
before the Timeout for Bus Watchdog (Register
No. 110) expires, the actuator controls to the Bus
Fail Position
Triggered bus watchdog is indicated in the Malfunction and Service Information (Register No. 105)
Bus fel
position
0: None / Last setpoint
1: Fast close
2: Fast open
3: Mid position (parameterized)
Default: None(0)
–
–
R/W
110
109
Timeout for Bus Watchdog in s
Time until Bus Fail will be detected. If Bus Watchdog = 0 then deactivated If Bus Fail Position
(Register No. 110) different from 0, the Bus Fail
Position becomes active after the Timeout for Bus
Watchdog is expired
Timeout
för Busövervakning i s
0...3‘600
Default: 0
If Bus Fail Position (Register No.
110) not None(0), then Default:
120
s
1
R/W
4
Swegon reserves the right to alter specifications
20220810
Mech travel increased
Actuator cannot move
Internal activity
Gear disengaged
Bus Watchdog triggered
REACT Parasol Zenith
Modbus Register Description
No.
Address
Description Comment
Beskrivning (SE)
Range Enumeration
Unit
Scaling
Access
111
110
Nominal volumetric flow
Nominellt volumetriskt flöde
–
m³/h
1
R
112
111
–
Nominellt volumetriskt flöde
LW
–
–
–
–
113
112
Nominal volumetric flow
Vnom in unit selected (Register 118)
LowWord Lower 16 bit of 32 bit
value
Nominellt volumetriskt flöde
HW
–
UnitSel
0.001
R
114
113
Nominal volumetric flow
Vnom in unit selected (Register 118)
HighWord Upper 16 bit of 32 bit
value
115
114
–
–
–
–
–
116
115
–
–
–
–
–
117
116
Control Mode
Läge styrning
0: Position control
1: Flow control
–
–
R/W
118
117
Unit Selection Flow
Enhetsinställning flöde
0: m³/s
1: m³/h
2: l/s
3: l/min
4: l/h
5: gpm
6: cfm
Default: m³/h(1)
–
–
R/W
119
118
Setpoint Source
Analog: Setpoint from analog signal
0 ... 10 V on wire 3 Bus: Setpoint
from Modbus (Register 1)
Börvärdeskälla
Analog: Börvärde från
analogsignal 0-10V
Bus: Börvärde från Modbus
0: Analog
1: Bus
Default: Bus(1)
–
–
R/W
20220810
Swegon reserves the right to alter specifications
5
">
