User Manual
Industrial Media Converter, with 1 x 100M SFP + 1 x 10/100M,
18-36VAC or 12-56 VDC input
FCC MARKING
This Equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received; including interference that may cause undesired operation.
CE MARKING
This equipment complies with the requirements relating to electromagnetic compatibility, EN 55032/24 class A for ITE, the essential protection requirement of
Council Directive 2014/30/EC on the approximation of the laws of the Member States relating to electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it may be possible that information in this document is not up-to-date. Please check with your local distributors for the latest information. No part of this document can be copied or reproduced in any form without written consent from the company.
Trademarks:
All trade names and trademarks are the properties of their respective companies.
1
Key Features
True Mini, hardened design enclosure 59x36x50mm (LxWxD)
Supports 18V-36VAC, 12V-56VDC or DC Jack socket
Supports Link Fault Pass through (LFP) function
Supports Switch Mode and Converter Mode.
Surge protection diodes on power input.
ESD protection diodes on RJ-45 port
Provides Far End Fault function on FX port.
Provides increased Noise Immunity
Extended environmental specification -40°C to 75°C
Introduction
This true mini, hardened Industrial Media Converter is designed for critical but space-limited outdoor CAM enclosure. It can be powered by wide range VAC, VDC or external DC power adapter. This unit can be either din-rail or wall mounted, both options are both included. It is an ideal unit for IP surveillance, traffic monitoring and security applications in critical environments. It can tolerate -40°C to 75°C in harsh environments to connect a reliable network.
2
Installation package
This unit can be din-rail mounted or wall-mounted. Din-rail brackets and wall-mount brackets are included.
Power connection
This unit provides a 3 pin terminal block. It can be operated using either VAC or VDC power sources. The VDC power range is from 12VDC to 56VDC, and the VAC power range is from
18VAC to 36VAC. Always make sure your input voltage is within this supported voltage range.
To connect power: Follow the printed polarity for V+, V- and Ground. Connect positive wire to
V+, connect negative wire to V- and also connect neutral wire to ground.
Power connecting procedure:
WARNING -- Always SHUT OFF power source to connect power wire.
WARNING – DO NOT force SFP fiber into SFP housing without removing terminal block.
WARNING -- Any exceeded input voltage will not make this unit function and may damage this unit.
STEP 1 – Pull out 3 pin terminal block.
STEP 2 – Connect wire to V+, V- and Ground.
STEP 3 – Connect SC/SFP/WDM fiber wire to fiber port.
STEP 4 – Plug back 3 pin terminal block to its place.
3
Dip switch function
This unit is equipped with dip switches, located on the front panel marked as SW1. Adjusting the dip switches will change the default function of this unit. This unit has set to manufacturer default as: Switch Mode ON and LFP function OFF.
The table shown as you may change the dip switch setting to your desired environment.
1 2
UP
DIP 1
UP LFP enabled
DOWN LFP disabled (default)
SW
1
DOWN
DIP 2
UP Converter Mode
DOWN Switch Mode (default)
LED indicator
PWR (Green)
ON – Power is detected
OFF – Power is not detected
LK/Act (Green)
ON – Fiber port is detected
Flashing – Fiber data is transmitting/receiving
Fiber Port
TX (Amber)
ON – 100M speed is detected
OFF – 10M speed is detected
TX (Green)
On – TX port is detected
Flashing – TX data is transmitting/receiving
4
Specification
IEEE Standard
Data Processing
Flow Control
Jumbo Frame
Architecture
Network Connector
LED Indicators
DIP Switch
Power Protection
Connector Protection
Reserve P olarity P rotection
Overload
C urrent
P rotection
Power Input
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast Ethernet
IEEE 802.3u 100Base-FX Fast Ethernet
IEEE802.3x Flow Control and Back Pressure
Store and Forward
IEEE 802.3x Flow Control and Back Pressure
9KB
Full wire speed conversion,
Transparent conversion to 802.1Q VLAN tagged packets.
1 x RJ-45 10/100BaseT(X) Auto negotiation,
Auto MDI/MDI-X function, Full/Half duplex
1 x 100M SFP
PWR(Green): ON - Power is detected
LK/Act (Green): ON - Fiber is detected
Flashing - Data is transmitting/receiving
RJ-45 port
Green: ON
-
TX link is detected
Flashing - TX data is transmitting/receiving
Amber: ON - 100M speed is detected
OFF - 10M speed is detected
DIP1: UP
-
LFP enable
DOWN
-
LFP disable (Default)
LFP (Link Fault Pass Through)
DIP2: UP - Converter Mode
DOWN - Switch Mode (Default)
Surge protection diodes on power input
ESD protection diodes on TX port
Present
Present
18V-36VAC, 12V-56VDC,
DC Jack terminal cable supported (DC Barrel
Connector)
5
Conformance to UL Standards
Power Consumption
Removable Terminal Block
Operating Temperature
Operating Humidity
Storage Temperature
Housing Design
Case Dimension (L X W X D)
Installation
Certifications
Safety
EMC/EMS
EMI
Vibration
Shock
Free Fall
Use Isolated power supply to conform with UL 508 standard
Full Load: 1.92Watts at 48VDC
3 pin contact terminal block for power input
Wire range: 0.34mm^2 to 2.5mm^2
Solid wire (AWG):12-24/14-22
Stranded wire (AWG): 12-24/14-22
Torque:5lb-In/0.5Nm/0.56Nm
Wire Strip length: 7-8mm
-40°C ~ 75°C
5% to 95% (Non-condensing)
-40°C ~ 85°C
IP40 Design, high graded Aluminum
59 x 36 x 50 mm (L x W x D)
DIN-Rail mounted, Panel Mounted
LVD (EN62368-1)
CE, FCC, EN55032/24, VCCI
FCC Part 15 Subpart B Class A
EN 60068-2-6
EN 60068-2-27
EN 60068-2-32
6
Housing Dimension (mm)
NOTE:
Housing dimension is for the purpose of showing product Length, Width, Height, din-rail, and terminal block’s position and dimension. Please reference the LED Indicator Page for correct port order.
7