Eizo FORIS FS2331 User's Manual

Cover

Important

Please read PRECAUTIONS, this User’s Manual, and Setup Guide

(separate volume) carefully to familiarize yourself with safe and effective usage.

• Please refer to the Setup Guide for basic information ranging from connection of the monitor to a PC or external device to using the monitor.

• The latest User’s Manual is available for download from our web site: http://www.eizo.com

Location of Caution Statement

<For USA-California Only>

CR Coin Lithium Battery contains Perchlorate Material - special handling may apply.

See www.dtsc.ca.gov/hazardouswaste/perchlorate .

Product specification may vary with sales areas. Confirm the specification in the manual written in language of the region of purchase.

Copyright© 2010 EIZO NANAO CORPORATION All rights reserved.

No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO NANAO CORPORATION.

EIZO NANAO CORPORATION is under no obligation to hold any submitted material or information confidential unless prior arrangements are made pursuant to EIZO NANAO CORPORATION’s receipt of said information.

Although every effort has been made to ensure that this manual provides up-to-date information, please note that

EIZO monitor specifications are subject to change without notice.

2

Notice for this monitor

This product is suited to creating documents, viewing multimedia content, and other general purposes.

This product has been adjusted specifically for use in the region to which it was originally shipped. If the product is used outside the region, it may not operate as specified in the specifications.

This product may not be covered by warranty for uses other than those described in this manual.

The specifications noted in this manual are only applicable for power cords and signal cables specified by us.

Use optional products manufactured or specified by us with this product.

As it takes about 30 minutes for the performance of electrical parts to stabilize, adjust the monitor 30 minutes or more after the monitor power has been turned on.

In order to suppress the luminosity change by long-term use and to maintain the stable luminosity, use of a monitor in lower brightness is recommended.

When the screen image is changed after displaying the same image for extended periods of time, an afterimage may appear. Use the screen saver or power save function to avoid displaying the same image for extended periods of time.

Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (refer to

“Cleaning” (page 4)

).

The LCD panel is manufactured using high-precision technology. However, missing pixels or lit pixels may appear on the LCD panel, this is not malfunction. Percentage of effective dots: 99.9994% or higher.

The backlight of the LCD panel has a fixed life span. When the screen becomes dark or begins to flicker, please contact your dealer.

Do not press on the panel or edge of the frame strongly, as this may result in the display malfunction, such as the interference patterns, etc. If pressure is continually applied to the panel, it may deteriorate or damage your panel. (If the pressure marks remain on the panel, leave the monitor with a white or black screen. The symptom may disappear.)

Do not scratch or press on the panel with any sharp objects, as this may result in damage to the panel. Do not attempt to brush with tissues as this may scratch the panel.

When the monitor is cold and brought into a room or the room temperature goes up quickly, dew condensation may occur inside and outside the monitor. In that case, do not turn the monitor on and wait until dew condensation disappears, otherwise it may cause some damages to the monitor.

3

Cleaning

Attention

• Never use any solvents or chemicals, such as thinner, benzene, wax, alcohol, and abrasive cleaner, which may damage the cabinet or panel.

Note

• Optional ScreenCleaner is recommended for cleaning the panel surface.

●

Panel

• Clean the panel with a soft cloth such as cotton cloth or lens cleaning paper.

• If necessary, stubborn stains can be removed by moistening part of a cloth with water to enhance its cleaning power. After that, clean the panel again with a dry cloth for better finishing.

●

Cabinet

• Clean the cabinet with a soft cloth dampened with a little mild detergent.

To use the monitor comfortably

• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor according to the environmental conditions.

• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.

4

CONTENTS

Cover ...................................................................... 1

Notice for this monitor ............................................ 3

CONTENTS ............................................................. 5

Chapter 1 Introduction ....................................... 7

1-1. Features ......................................................... 7

1-2. Controls and Functions ............................... 8

●

BeforeUsingRemoteControl......................... 9

Howtoinstallbattery................................... 9

ReceivableRangeofRemoteControl......... 9

1-3. EIZO LCD Utility Disk...................................10

●

Diskcontentsandsoftwareoverview............10

Touse“ScreenManagerProfor

LCD(DDC/CI)/EIZOScreenSlicer”.................10

1-4. Basic Operations and Functions ...............11

●

BasicoperationoftheSettingmenu..............11

Functions........................................................12

Chapter 2 Adjusting Screens .......................... 13

2-1. Compatible Resolutions/Formats ..............13

AnalogInput(D-Sub)..................................13

DigitalInput(DVI-D,HDMI:PCsignal).......13

DigitalInput(HDMI:videosignal)...............13

2-2. Setting the Resolution ................................14

Windows7..................................................14

WindowsVista............................................14

WindowsXP................................................14

MacOSX....................................................14

2-3. Adjusting Color ............................................15

●

Toselectthedisplaymode(ColorMode).......15

Toperformadvancedadjustments................16

Adjustablesettingsineachmode..................16

●

Toadjustbrightness“Brightness”..................17

Toadjustblacklevel“BlackLevel”.................17

●

Toadjustcontrast“Contrast”..........................18

Toadjustthecolorsaturation“Saturation”.....18

●

Toadjusthue“Hue”........................................19

Toadjustcolortemperature“Temperature”...19

●

TosetContrastEnhancer

“ContrastEnhancer”....................................... 20

●

Toreduceimageblur“PowerResolution”..... 20

●

●

Toadjustgamma“Gamma”...........................21

Toadjustgain“Gain”......................................21

Tosetoverdriveintensity“Overdrive”........... 22

2-4. Screen Adjustment ..................................... 22

●

DigitalSignalInput........................................ 22

AnalogSignalInput....................................... 22

2-5. Screen Size Changing ................................ 26

●

AnalogInput(D-Sub)/DigitalInput

(DVI-D,HDMI:PCsignal)............................. 26

●

DigitalInput(HDMI:videosignal)................. 27

Tosetthescreenratio“Overscan”............ 27

Chapter 3 Setting Monitor ............................... 28

3-1. Adjusting Volume........................................ 28

●

Toturnthevolumeup/down.......................... 28

Tomutethesoundtemporarily...................... 28

3-2. Switching sound source for HDMI signal input “Source” ............................................. 28

3-3. To adjust the sound level “Sound Level” . 29

3-4. Enabling/Disabling DDC/CI communication “DDC/CI” .......................... 29

3-5. Locking Buttons “Key Lock” ..................... 29

3-6. Setting the EIZO Logo Display “Logo” .... 30

3-7. Setting Language “Language” .................. 30

3-8. Changing the HDCP authentication setting for HDMI signal input ..................... 30

3-9. Resetting the Monitor to the Default

Settings .........................................................31

●

Toresetthecoloradjustments“ColorReset”31

●

Toresetalladjustmentstothedefault settings“Reset”..............................................31

Chapter 4 Power Saving Functions ................ 32

4-1. Setting Power Saving “Power Save” ........ 32

●

Monitor.......................................................... 32

AudioOutput................................................. 33

4-2. Setting Power Indicator “Power

Indicator” ..................................................... 33

4-3. Enabling/Disabling Automatic

Brightness Adjustment “Auto EcoView” . 34

4-4. Checking the power saving level .............. 34

4-5. Enabling/Disabling Auto Power-OFF

“Off Timer (min)” ......................................... 34

Chapter 5 Connecting Cables ......................... 36

5-1. Connecting Multiple External Devices ..... 36

●

Toswitchamonginputsignals...................... 36

Chapter 6 Troubleshooting .............................. 37

Chapter 7 Reference ........................................ 41

7-1. How to Attach the Optional Arm ................41

7-2. Attaching the Stand base .......................... 42

7-3. Displaying Monitor Information

“Information” ............................................... 42

7-4. Specifications ............................................. 43

7-5. Glossary ....................................................... 46

7-6. Preset Timing .............................................. 48

CONTENTS

5

Appendix .............................................................. 49

Trademark ............................................................... 49

License .................................................................... 49

ENERGY STAR ........................................................ 49

TCO .......................................................................... 50

FCC Declaration of Conformity ............................ 50

Hinweise zur Auswahl des richtigen

Schwenkarms für Ihren Monitor ......................51

Hinweis zur Ergonomie : ........................................51

LIMITED WARRANTY ............................................. 52

China Measures for RoHS Compliance in

ChinaRoHS .........................................................61

6

CONTENTS

Chapter 1 Introduction

Thank you very much for choosing an EIZO color LCD monitor.

1-1. Features

• 23″ wide format LCD

• Applicable to the resolution of 1920 × 1080.

• Panel with a wide field of view adopted

VA panel with 178º horizontal and vertical viewing angles.

• HDMI connector × 2

- Applicable to the PC input signal using HDMI input, allowing three different digital signal inputs from a PC.

• The Color Mode function allows the user to select the display mode optimum to the displayed image.

- The Paper mode reproduces an easy-on-the-eyes display that looks just like printed paper.

See

“To select the display mode (Color Mode)” (page 15)

.

• ContrastEnhancer function

Automatically adjusts the contrast according to the image, enabling the display of high contrast and sharp animated images.

See

“To set ContrastEnhancer “ContrastEnhancer”” (page 20) .

• Power Resolution function

You can reduce image blur by enhancing its outline.

See

“To reduce image blur “Power Resolution”” (page 20)

.

• Two dedicated gamma modes (“Power1”/“Power2”) suitable for game images implemented

The images will be sharpened by increasing the halftone (Power1) and low-tone (Power2) contrasts.

See

“To adjust gamma “Gamma”” (page 21)

.

• A variety of Screen Size can be selected, such as dot by dot (image is displayed without scaling the input signals), Letterbox, Overscan (change of the display area of the input image)

See

“2-5. Screen Size Changing” (page 26) .

• The software “ScreenManager Pro for LCD (DDC/CI)” to adjust the screen using the mouse and keyboard is included.

See

“1-3. EIZO LCD Utility Disk” (page 10) .

• Remote control enables easy operation, setting and adjustment of the monitor.

See

“1-2. Controls and Functions” (page 8)

.

• Color sheets (in three colors) to be pasted at the bottom of the monitor included

Select your desired color to add an accent to the monitor.

See “Setup Guide”.

• HDCP (High-bandwidth Digital Content Interface)

• Built-in stereo speakers and headphone jack

See

“1-2. Controls and Functions” (page 8)

.

Chapter1Introduction

7

1-2. Controls and Functions

Monitor

Menu

Color

Screen

Sound

PowerManager

Monitor Settings

Information

Settingmenu

*1

14

12

13

1 2 3 4 5 6 7 8 9 10 11

1. Auto EcoView sensor Detectsambientbrightness.AutoEcoViewfunction(

page34

).

2. Remote control detector

Receivesthesignalfromtheremotecontrol.

3. button

Switchesinputsignalsfordisplay( page36

).

PC1(DVI)→PC2(D-SUB)→HDMI1→HDMI2

4. /

5. button

button Displaysthevolumeadjustmentmenutovolumeupordown.

Turnsthepoweronoroff.

Indicatesthemonitor’soperationstatus.

Blue: Operating

6. Power indicator

Orange:

Red

OFF:

Powersavingmode

Poweroff

Mainpoweroff

7. Main power switch

8. Power connector

Turnsthemainpoweronoroff.

Connectsthepowercord.

9. Input signal connector

Left:HDMIconnector×2(HDMI1,HDMI2)/Center:DVI-Dconnector/

Right:D-Submini15-pinconnector

10. Stereo mini jack

11. Headphone jack

12. Security lock slot

13. Stand

*2

Connectsthestereominijackcable.

Connectstheheadphones.

ComplieswithKensington’sMicroSaversecuritysystem.

Usedtoadjusttheangleofthemonitorscreen.

14. Speaker

Outputsaudiosource.

*1

See

page11 forhowtouse.

*2

Anoptionalarm(oranoptionalstand)canbeattachedbyremovingthestand(see

“7-1.HowtoAttachtheOptional

Arm”(page41)

).

8


Remote Control

10

11

1

5

8

9

2 3

4

6

7

12

13

1. OFF TIMER

2. DISPLAY

Setsthetimeuntilthemonitorpower-off.

Displaysthecurrentinputport.

3. SCREEN SIZE

Changesthescreensize.

4. POWER

Turnsthepoweronoroff.

5. INPUT SELECT Switchesinputsignalsfordisplay.

PC

PC1(DVI)→PC2(D-SUB)

HDMI

HDMI1→HDMI2

6. MUTE

7. VOLUME +/-

8. MENU

9. RETURN

Mutessoundtemporarily.

Adjuststhevolume.

Displays/ExitstheSettingmenu.

Returnstothepreviousmenuinmenuoperation.

10. / / /

11. ENTER

• Choosesandincreases/decreasesadjustmentsettings foradvancedadjustmentusingtheSettingmenu.

• / :Displaysthebrightnessadjustmentmenu(

page

17 ).

Determinesanitemonthemenuscreen,andsaves valuesadjusted.

12. MODE

13. EcoView

Changesthecolormode.

Displays/ExitstheEcoViewmenu.

●

Before Using Remote Control

How to install battery

1. While pushing the tab toward the arrow (1), pull out the battery case (2).

(1)

(2)

2. Insert a battery with the positive side up. (Battery model number: CR2032)

3. Insert the battery case until it clicks.

Receivable Range of Remote Control

Use the remote control inside of the range as below.

5m

7m

30°

30°

5m

7m

5m

20°

20°

5m


9

1-3. EIZO LCD Utility Disk

An “EIZO LCD Utility Disk” (CD-ROM) is supplied with this product. The following table shows the disk contents and the overview of the software programs.

●

Disk contents and software overview

The disk includes software programs for adjustment, and User’s Manual. Refer to Readme.txt file on the disk for software startup procedures or file access procedures.

AReadme.txtfile

Item

Screenadjustmentpatternfiles

Overview

ScreenManagerProforLCD(DDC/

CI)

EIZOScreenSlicer

User’sManualofthismonitor(PDFfile)

Usedwhenadjustingtheimageofanalog signalinputmanually.

Softwareforadjustingthescreenusingthe mouseandkeyboard

ThissoftwaredoesnotrunonaPC connectedviatheHDMIinput.

Softwarethatdividesascreenandlaysout multiplewindowsefficiently.

Windows Macintosh

√ √

√ √

√

√

√

●

To use “ScreenManager Pro for LCD(DDC/CI)/EIZO ScreenSlicer”

For the installation and use of “ScreenManager Pro for LCD(DDC/CI)/EIZO SceenSlicer”, refer to the respective User’s Manual on the disk.

√

-

-

10


1-4. Basic Operations and Functions

●

Basic operation of the Setting menu

1.

Displaying the Setting menu

1. Press on the remote control. The Setting menu appears.

Menu

Color

Screen

Sound

PowerManager

Monitor Settings

Information

2.

Adjusting/Setting

1. Choose a menu to adjust/set with , , and then press . The Sub menu appears.

Return

Color Mode

Brightness

Black Level

Contrast

Saturation

Hue

Temperature

Advanced Settings

Color Reset

Color

2. Choose an item to adjust/set with , , and then press . The adjustment/ setting menu appears.

Brightness

60

3. Adjust/set the selected item with , , , , and then press .

3.

Exiting

1. Press .

Note

• To go back to the previous menu, press .


11

●

Functions

The following table shows all the Setting menu’s adjustment and setting menus.

Main menu

Color

*1

Screen

Setting

ColorMode

Brightness

BlackLevel

Contrast

Saturation

Hue

Temperature

AdvancedSettings ContrastEnhancer

PowerResolution

Gamma

Gain

Overdrive

ColorReset

AutoScreenAdjust

*2

AutoRangeAdjust *2

Clock

*2

Phase

*2

Position

*2

ColorSpace

*3

Smoothing

Source

*3

Reference

“2-3.AdjustingColor”(page15)

“2-4.ScreenAdjustment”(page22)

Sound

PowerManager

MonitorSettings

SoundLevel

PowerSave

PowerSave

DDC/CI

KeyLock

“3-2.Switchingsoundsourcefor

HDMIsignalinput“Source””(page28)

“3-3.Toadjustthesoundlevel

“SoundLevel””(page29)

“4-1.SettingPowerSaving“Power

Save””(page32)

“3-4.Enabling/DisablingDDC/CI communication

“DDC/CI””(page29)

“3-5.LockingButtons“KeyLock””

(page29)

Information

Logo

PowerIndicator

Language

Reset

“3-6.SettingtheEIZOLogoDisplay

“Logo””(page30)

“4-2.SettingPowerIndicator“Power

Indicator””(page33)

“3-7.SettingLanguage“Language””

(page30)

“3-9.ResettingtheMonitortothe

DefaultSettings”(page31)

“7-3.DisplayingMonitorInformation

“Information””(page42)

*1

*2

*3

Theadjustment/settingsavailableonthe“Color”menudependontheselectedColormode.Theabove tableshowsthesubmenuswhentheUser1orUser2modeisselected.

Thesefunctionscanbeadjustedwithanaloginput.

ThisfunctionisavailablewithHDMIsignalinput.

12


Chapter 2 Adjusting Screens

2-1. Compatible Resolutions/Formats

The monitor supports the following resolutions and signal format.

Analog Input (D-Sub)

Resolution

640×480

720×400

800×600

1024×768

1280×720

1280×960

1280×1024

1680×1050

1920×1080*

Applicable Signals

VGA,VESA,CEA-861

VGATEXT

VESA

VESA

CEA-861

VESA

VESA

VESACVT,VESACVTRB

CEA-861

Vertical Scan

Frequency

upto75Hz

70Hz upto75Hz upto75Hz

60Hz

60Hz upto75Hz

60Hz

60Hz

Dot Clock

148.5MHz

(Max.)

Digital Input (DVI-D, HDMI: PC signal)

Resolution

640×480

720×400

800×600

1024×768

1280×720

1280×960

1280×1024

1680×1050

1920×1080*

Applicable Signals

VGA,CEA-861

VGATEXT

VESA

VESA

CEA-861

VESA

VESA

VESACVT,VESACVTRB

CEA-861

Vertical Scan

Frequency

60Hz

70Hz

60Hz

60Hz

60Hz

60Hz

60Hz

60Hz

60Hz

Dot Clock

*

A graphics board in conformance with the VESA and CEA-861 standards is required.

Recommended resolution

148.5MHz

(Max.)

Digital Input (HDMI: video signal)

• Video signal

- VGA / 525i (480i)/525p (480p)/1125i (1080i)/750p (720p)/1125p (1080p): 60 Hz

- 625i (576i)/625p (576p)/1125i (1080i)/750p (720p)/1125p (1080p): 50 Hz

• Audio signal

- 2ch linear PCM (32 kHz / 44.1 kHz / 48 kHz)

Chapter2AdjustingScreens

13

2-2. Setting the Resolution

When you connect the monitor to the PC and find that the resolution is improper, or when you want to change the resolution, follow the procedure below.

Windows 7

1. Right-click the mouse anywhere on the desktop except for icons.

2. From the displayed menu, click “Screen resolution”.

3. On the “Screen Resolution” dialog box, select the monitor.

4. Click “Resolution” to select the desired resolution.

5. Click the [OK] button.

6. When a confirmation dialog box is displayed, click [Keep changes].

Windows Vista


2. From the displayed menu, click “Personalize”.

3. On the “Personalization” window, click “Display Settings”.

4. On the “Display Settings” dialog box, select the “Monitor” tab and select desired resolution in the

“Resolution” field.

5. Click the [OK] button.

6. When a confirmation dialog box is displayed, click [Yes].

Windows XP


2. From the displayed menu, click “Properties”.

3. When the “Display Properties” dialog box is displayed, click the “Settings” tab and select desired resolution for “Screen resolution” under “Display”.

4. Click the [OK] button to close the dialog box.

Mac OS X

1. Select “System Preferences” from the Apple menu.

2. When the “System Preferences” dialog box is displayed, click “Displays” for “Hardware”.

3. On the displayed dialog box, select the “Display” tab and select desired resolution in the “Resolutions” field.

4. Your selection will be reflected immediately. When you are satisfied with the selected resolution, close the window.

14


2-3. Adjusting Color

●

To select the display mode (Color Mode)

This function allows easy selection of a desired mode according to monitor application.

Display Modes

User1

Mode

User2 sRGB

Paper

Game

Cinema

Purpose

Selectoneoftheseusermodestodefineadesiredsetofparametersettings.

SuitableforcolormatchingwithsRGBcompatibleperipherals.

Producesaprintedpapereffectbydecreasingcontrastandcolortemperature.

Suitablefordisplayinggameimages.

Suitablefordisplayingmovie-likeimages.

Displaysthecurrentmode.

Color Mode

User1

Procedure

1. Press on the remote control.

The mode name appears at the center of the screen.

2. The mode among the list is highlighted in turn each time is pressed.

You can switch the current mode with or while the mode menu is being displayed.

→User1←→User2←→sRGB←→Paper←→Game←→Cinema←

Note

• The Setting menu and the Mode menu cannot be displayed at the same time.

• “ScreenManager Pro for LCD (DDC/CI)” allows you to select the Color mode automatically according to the application used (see “Chapter 3 Auto Fine-Contrast” in the “ScreenManager Pro for LCD (DDC/CI)” User’s

Manual).


15

●

To perform advanced adjustments

The “Color” menu of the Setting menu allows you to set and save the independent color adjustment for each mode.

Attention

• The monitor will take about 30 minutes before its internal electric components stabilize. Wait 30 minutes or more after turning the monitor power on before starting adjustment.

• Perform the range adjustment first when adjusting color for analog signals (see

“To adjust color gradation automatically “Auto Range Adjust”” (page 25)

).

• The same image may be seen in different colors on multiple monitors due to their monitor-specific characteristics.

Make fine color adjustment visually when matching colors on multiple monitors.

Note

• The value shown in “K” is available only as reference.

• Using the “ScreenManager Pro for LCD (DDC/CI)” allows you to perform the color adjustment by using the mouse and keyboard of your PC. (Refer to “Chapter 4 Color Adjustment” in the User’s Manual for “ScreenManager Pro for

LCD (DDC/CI)”.)

●

Adjustable settings in each mode

The adjustable settings depend on the mode. (You cannot select any non-adjustable or non-settable function.)

For instructions on how to adjust or set each function, refer to subsequent pages.

√: Adjustable -: Not adjustable

Color Mode

Function

Brightness

BlackLevel

Contrast

Saturation

Hue

Temperature

AdvancedSettings ContrastEnhancer

PowerResolution

Gamma

Gain

Overdrive

ColorReset

√

√

√

√

√

√

√

√

√

√

User1

User2

√

√ sRGB

-

-

-

-

-

-

√

-

-

√

-

-

Paper

-

-

√

-

-

-

√

-

√

-

-

-

Game

√

√

√

√

√

√

√

√

√

√

√

-

Cinema

√

√

√

√

√

√

√

√

-

√

-

-

16


●

To adjust brightness “Brightness”

The screen brightness is adjusted by changing the brightness of the backlight (light source from the LCD back panel).

Adjustable range

0 to 100

Procedure

1. Choose “Color” in the Setting menu, and press .

2. Choose “Brightness” in the “Color” menu, and press .

The “Brightness” menu appears.

3. Use or for adjustment.

4. Press to exit the adjustment.

Note

• While the Setting menu is not displayed, or on the remote control is available for adjustment.

• If you feel that the image is too bright even if the brightness is set to 0 or that the image is too dark even if the brightness is set to 100, adjust the contrast.

●

To adjust black level “Black Level”

You can adjust the black level of images.


0 to 100

Procedure


2. Choose “Black Level” in the “Color” menu, and press .

The “Black Level” menu appears.



Note

• After completing black level adjustment, readjust the contrast as appropriate.


17

●

To adjust contrast “Contrast”

The brightness of the screen is adjusted by varying the video signal level.


0 to 100

Procedure


2. Choose “Contrast” in the “Color” menu, and press .

The “Contrast” menu appears.



Note

• In the contrast of 50, every color gradation is displayed (for PC input signal only).

• When adjusting the monitor, it is recommended to perform the brightness adjustment which may not lose the gradation characteristics, prior to the contrast adjustment.

• Perform the contrast adjustment in the following cases.

- When you feel the image is too dark even if the brightness is set to 100 (Set the contrast to higher than 50.)

- When you feel the image is too bright even if the brightness is set to 0 (Set the contrast to lower than 50.)

●

To adjust the color saturation “Saturation”

This function allows you to adjust color saturation.


-50 to 50

Procedure


2. Choose “Saturation” in the “Color” menu, and press .

The “Saturation” menu appears.



Attention

• Using this function may make some color gradations unavailable for display.

Note

• The minimum value (-50) changes the screen to monochrome.

18


●

To adjust hue “Hue”

This function allows you to adjust hue.


-50 to 50

Procedure


2. Choose “Hue” in the “Color” menu, and press .

The “Hue” menu appears.



Attention


●

To adjust color temperature “Temperature”

Color temperature can be adjusted.

The color temperature is normally used to express the hue of “White” and/or “Black” by a numerical value.

The value is expressed in degrees “K” (Kelvin).

The screen becomes reddish at a low color temperature, and bluish at a high color temperature, like the flame temperature. A gain preset value is set for each color temperature setting value.


Off, 4000K-10000K (specified by every 500K unit, including 9300K)

Procedure


2. Choose “Temperature” in the “Color” menu, and press .

The “Temperature” menu appears.



Note

• “Gain” allows you to perform more advanced adjustment (see

“To adjust gain “Gain”” (page 21)

).

• If you set to “Off”, the image is displayed in the preset color of the monitor (Gain: 100 for each RGB).

• When gain is changed, the color temperature is changed to “Off”.


19

●

To set ContrastEnhancer “ContrastEnhancer”

This function allows you to set whether to automatically adjust the contrast according to the darkness or brightness of a scene, for example.

Procedure


2. Choose “Advanced Settings” in the “Color” menu, and press .

3. Choose “ContrastEnhancer” in the “Advanced Settings” menu, and press .

The “ContrastEnhancer” menu appears.

4. Select “Enable” or “Disable” with or .


Note

• Setting “Enable” allows you to display high contrast and sharp images.

●

To reduce image blur “Power Resolution”

You can reduce image blur by enhancing its outline.


Off, 1, 2, 3

Procedure



3. Choose “Power Resolution” in the “Advanced Settings” menu, and press .

The “Power Resolution” menu appears.



Note

• If you keep pressing the or button for two seconds or more while “Power Resolution” is displayed, the monitor enters the demo mode. To return to normal display, keep pressing or for at least two seconds.

- Left half of screen:

- Right half of screen:

Power Resolution On

Power Resolution Off

20


●

To adjust gamma “Gamma”

Gamma can be adjusted. The brightness of the monitor varies depending on the input signal, however, the variation rate is not proportional to the input signal. To keep the balance between the input signal and the brightness of the monitor is called as “Gamma correction”.


1.8, 2.0, 2.2, 2.4, 2.6, 2.8, Power1, Power2

Procedure



3. Choose “Gamma” in the “Advanced Settings” menu, and press .

The “Gamma” menu appears.



Note

• Choosing “Power1” will help to sharpen halftone images by increasing their contrast.

• Choosing “Power2” will help to make dark images visible by increasing the low-tone contrast.

●

To adjust gain “Gain”

The brightness of each color component red, green, and blue is called “Gain”. You can change the hue of

“white” by adjusting gain.


0 to 100

Procedure



3. Choose “Gain” in the “Advanced Settings” menu, and press .

The “Gain” menu appears.

4. Adjust gain with or for each of red, green, and blue.


Attention


Note

• The value of gain changes with that of color temperature.

• When gain is changed, the color temperature is changed to “Off”.


21

●

To set overdrive intensity “Overdrive”

This function allows you to set overdrive intensity based on the use of the monitor. You can reduce Image lags by setting it to “Enhanced” when displaying animated images.


Enhanced, Standard, Off

Procedure



3. Choose “Overdrive” in the “Advanced Settings” menu, and press .

The “Overdrive” menu appears.



Attention

• The overdrive function is disabled in the following cases:

- The vertical scan frequency of input signals is more than 60 Hz

- The screen size is “Normal” (excluding the case that the display resolution is 1920 x 1080) or “Letterbox”

2-4. Screen Adjustment

●

Digital Signal Input

When digital signals are input, images are displayed correctly based on the preset data of the monitor, but if characters and/or lines appear blurred, go to

“6. Modify blurred characters or lines.” (page 26) .

When performing more advanced adjustment, see “2-3. Adjusting Color” (page 15)

and subsequent pages.

●

Analog Signal Input

Attention

• The monitor will take about 30 minutes before its internal electric components stabilize. Wait 30 minutes or more after turning the monitor power on before starting adjustment.

• The Self Adjust (automatic screen adjustment) function does not work for the images under the resolution of 800 ×

600 (SVGA).

• The self adjustment (or automatic screen adjustment) function works correctly when an image is fully displayed over the Windows or Macintosh display area. They do not work properly in the cases below:

- When an image is displayed only on a part of the screen (command prompt window, for example)

- When a black background (wallpaper, etc.) is in use

Also, these functions cannot work properly in some graphic boards.

The monitor screen adjustment is used to suppress flickering of the screen or adjust screen position and screen size correctly according to the PC to be used.

Note

• The Self Adjust function works when all of the following conditions are satisfied:

- When a signal is input into the monitor for the first time or when a resolution or vertical/horizontal scan frequency not used before is set

If the screen is not displayed correctly even after performing the Self Adjust operation, adjust the screen according to the procedures on the following pages to use the monitor comfortably.

22


Setting Procedures

1.

Perform the auto adjustment.

●

To adjust flickering, screen position, and screen size automatically “Auto Screen

Adjust”

Procedure

1. Choose “Screen” in the Setting menu, and press .

2. Choose “Auto Screen Adjust” in the “Screen” menu, and press .

3. Select “Yes” with or , and press .

Flickering, screen position, and screen size are corrected by the auto-adjustment function.

Ifthescreenisnotdisplayedcorrectlyevenafterperforming

“1.Performtheautoadjustment.”(page23)

, performtheadjustmentsaccordingtotheproceduresonthefollowingpages.Ifthescreenisdisplayed

correctly,goto “5.Adjustingcolorgradation.”(page25)

.

2.

Prepare to use analog screen adjustment patterns.

Load the “EIZO LCD Utility Disk” to your PC, and then open the “Screen adjustment pattern files”.

Note

• For details and instructions on opening the “Screen adjustment pattern files”, refer to the Readme.txt file.

3.

Perform the auto adjustment again with the analog screen adjustment pattern displayed.

●

To adjust flickering, screen position, and screen size automatically “Auto Screen

Adjust”

Procedure

1. Display Pattern 1 in full screen on the monitor using the “Screen adjustment pattern files”.


3. Choose “Auto Screen Adjust” in the “Screen” menu, and press .


Flickering, screen position, and screen size are corrected by the auto-adjustment function.

Ifthescreenisnotdisplayedcorrectlyevenafterperforming

“3.Performtheautoadjustmentagain withtheanalogscreenadjustmentpatterndisplayed.”(page23)

,performtheadjustmentsaccordingto

theproceduresonthefollowingpages.Ifthescreenisdisplayedcorrectly,goto “5.Adjustingcolor gradation.”(page25) .


23

4.

Choose “Screen” from the Setting menu to perform advanced adjustments.

Adjust the clock, phase and position, in this order.

●

To eliminate vertical bars “Clock”

Procedure

1. Choose “Clock” in the “Screen” menu, and press .

The “Clock” menu appears.

2. Adjust the clock with or to eliminate vertical bars.

Press or slowly so as not to miss the adjustment point.


When blurring, flickering or bars appear on the screen after adjustment, proceed to “Phase” to remove flickering or blurring.

●

To remove flickering or blurring “Phase”

Procedure

1. Choose “Phase” in the “Screen” menu, and press .

The “Phase” menu appears.

2. Adjust the phase with or to minimize flickering or blurring.


When vertical bars appear on the screen after adjustment, go back to “To eliminate vertical bars “Clock””.

(Clock → Phase → Position)

Attention

• Flickering or blurring may not be eliminated depending on your PC or graphics board.

24


●

To correct the screen position “Position”

Note

• Since the number of pixels and the pixel positions are fixed on the LCD monitor, only one position is provided to display images correctly. The position adjustment is made to shift an image to the correct position.

Procedure

1. Choose “Position” in the “Screen” menu, and press .

The “Position” menu appears.

2. Adjust the position with / / / .


4. Close Pattern 1.

5.

Adjusting color gradation.

●

To adjust color gradation automatically “Auto Range Adjust”

Every color gradation (0 to 255) can be displayed by adjusting the signal output level.

Procedure

1. Display Pattern 2 in full screen on the monitor using the “Screen adjustment pattern files”.


3. Choose “Auto Range Adjust” in the “Screen” menu, and press .

The “Auto Range Adjust” menu appears.


The output range is set automatically.

5. Close Pattern 2.


25

6.

Modify blurred characters or lines.

●

To modify blurred characters/lines “Smoothing”

When an image is displayed with a resolution other than recommended, the characters or lines of the displayed image may blur.

Attention

• Smoothing setting may not be required depending on the display resolution. (You cannot choose the smoothing icon.)


1 to 5

Procedure


2. Choose “Smoothing” in the “Screen” menu, and press .

The “Smoothing” menu appears.



2-5. Screen Size Changing

●

Analog Input (D-Sub)/Digital Input (DVI-D, HDMI: PC signal)

The image with the resolution other than the recommended resolution is displayed in full screen automatically. You can change the screen size by using the “Screen Size” function.

Setting

FullScreen

Enlarged

Function

Displaysanimageinfullscreen.Imagesaredistortedinsomecasesbecausethe verticalrateisnotequaltothehorizontalrate.

Displaysanimageinfullscreen.Insomecases,ablankhorizontalorverticalborder appearstoequalizetheverticalrateandthehorizontalrate.

Displaysimageswiththespecifiedresolution.

Normal

Example: Image size 1024 × 768

FullScreen Enlarged Normal

(1920×1080)

Procedure


Each time you press , the size changes.

(1440×1080)

Attention

• Selecting “Normal” may make some color gradations unavailable for display.

(1024×768)

26


●

Digital Input (HDMI: video signal)

The screen size can be changed with the “Screen Size” function.

Auto

Setting

FullScreen

Enlarged

Letterbox

Normal

*1

Function

Themonitorautomaticallychangesthescreen sizeaccordingtotheaspectratioandresolution informationfromtheexternaldevice.Thiscanbeset onlyforHDMI(SDSignal)input.

Displaysanimageinfullscreen.Imagesare distortedinsomecasesbecausetheverticalrateis notequaltothehorizontalrate.

Displaysanimageinfullscreen.Insomecases, ablankhorizontalorverticalborderappearsto equalizetheverticalrateandthehorizontalrate.

DisplaysLetterboxof16:9infullscreen.Exceptfor

Letterbox,theupperandlowerpartsoftheprojected imagearecut.ThiscanbesetonlyforHDMI(SD

Signal)input.

Theimageisdisplayedwithoutscalingtheinput signals.

*1 When“ScreenSize”is“Normal”,“Overscan”isfixedat“Off”.

Procedure


Each time you press , the size changes.

Attention

• Selecting “Normal” may make some color gradations unavailable for display.

Screen Display

To set the screen ratio “Overscan”

In order to hide distortion or noise at the image’s edge, the display area of the input image can be changed so that peripheral images are not displayed.

On

Off

Setting Function

Displaysaninputimageinthescreenbytrimmingtheverticalandhorizontalpartsofthe image.

Displaysmostoftheinputimage.

Procedure


The “Screen Size” menu appears.

2. Select “Overscan” with .



Attention

• When “Screen Size” is “Normal”, “Overscan” is fixed at “Off”.


27

Chapter 3 Setting Monitor

3-1. Adjusting Volume

●

To turn the volume up/down

This function allows you to adjust the volume.


0 to 30

Procedure

1. Press or on the remote control.

Note

• Alternatively, you can use

8)

).

or on the monitor for adjustment. (see

“1-2. Controls and Functions” (page

• The volume for the HDMI1, HDMI2, and the stereo mini jack can be set individually.

●

To mute the sound temporarily

Procedure


Mute sound temporarily.

By pressing the button again or pressing , the sound comes back.

Note

• The mute setting can also be released by pressing

• While the monitor is muted, press or

on the monitor.

on the monitor to decrease the volume setting.

3-2. Switching sound source for HDMI signal input

“Source”

This function allows you to switch sound source for HDMI signal input. You can select the HDMI or stereo mini jack.

Procedure

1. Choose “Sound” in the Setting menu, and press .

2. Choose “Source” in the “Sound” menu, and press .

The “Source” menu appears.

3. Select “HDMI” or “Stereo Mini Jack” with or .


Note

• This function is available with HDMI signal input. However, if a DVI-HDMI adapter cable is used, the sound source is automatically “Stereo Mini Jack” and cannot be changed.

28

Chapter3SettingMonitor

3-3. To adjust the sound level “Sound Level”

The input sound level can be adjusted.

The volume difference may occur depending on the kinds of input signals, since the average sound level of the external device differs.


-1 to 1

Procedure


2. Choose “Sound Level” in the “Sound” menu, and press .

The “Sound Level” menu appears.



Note

• For example, if the volume difference of PC1 and PC2 input signals becomes large, you can reduce the volume difference between them by raising the “Sound Level” of the lower volume side.

3-4. Enabling/Disabling DDC/CI communication

“DDC/CI”

This function allows you to enable/disable the DDC/CI communication (see

“7-5. Glossary” (page 46)

).

Procedure

1. Choose “Monitor Settings” in the Setting menu, and press .

2. Choose “DDC/CI” in the “Monitor Settings” menu, and press .

The “DDC/CI” menu appears.



Note

• HDMI input does not support DDC/CI communication.

3-5. Locking Buttons “Key Lock”

This function allows you to lock the buttons on the monitor.

Procedure


2. Choose “Key Lock” in the “Monitor Settings” menu, and press .

The “Key Lock” menu appears.

3. Select “On” with or .


Note

• The following operations are available even if the buttons are locked:

- Turning on or off the monitor with the Power button

• Does not lock the remote control operation.


29

3-6. Setting the EIZO Logo Display “Logo”

When the monitor is turned on, the EIZO logo appears on the screen. You can choose to display or not to display the EIZO logo.

Procedure


2. Choose “Logo” in the “Monitor Settings” menu, and press .

The “Logo” menu appears.

3. Select “On” or “Off” with or .


3-7. Setting Language “Language”

This function allows you to select a language for the Setting menu or displaying message.

Selectable languages

English/German/French/Spanish/Italian/Swedish/Japanese/Simplified Chinese/Traditional Chinese

Procedure


2. Choose “Language” in the “Monitor Settings” menu, and press .

The “Language” menu appears.

3. Choose a language with or .


3-8. Changing the HDCP authentication setting for

HDMI signal input

The external device cannot be authenticated successfully according to your external device and the screen cannot be displayed. In this case, follow the procedures below to change the HDCP from the normal to extended state.

Procedure

1. Press on the remote control or on the monitor to turn OFF the monitor power.

2. Press on the monitor for five seconds or more.

The setting changes and the monitor power is turned on.

Note

• The current setting status can be identified based on the color used to display the input port or signal error.

Setting Input port Signal Error

Normal

HDMI1

HDMI1

Signal Error

Extended

HDMI1

HDMI1

Signal Error

30


3-9. Resetting the Monitor to the Default Settings

There are two different Resets: Color Reset for only resetting the color adjustments to the default settings and

Full Reset for resetting all settings to the defaults.

Attention

• After resetting, you cannot undo the operation.

Note

• Regarding the default setting, see “Main Default Settings” (page 44)

.

●

To reset the color adjustments “Color Reset”

This function only resets the color adjustments for the currently selected mode to the default settings.

Procedure


2. Choose “Color Reset” in the “Color” menu, and press .

3. Select “Yes” with or .

4. Press .

The color adjustments revert to the default settings.

●

To reset all adjustments to the default settings “Reset”

This function resets all adjustments to the default settings.

Attention

• The reset operation cannot return the HDCP authentication setting (

“3-8. Changing the HDCP authentication setting for HDMI signal input” (page 30)

) to the default setting.

Procedure


2. Choose “Reset” in the “Monitor Settings” menu, and press .

3. Select “Yes” with or .

4. Press .

All adjustments revert to the default settings.


31

Chapter 4 Power Saving Functions

4-1. Setting Power Saving “Power Save”

●

Monitor

This function allows you to specify whether to set the monitor into the power saving mode, depending on the state of an external device connected to it. When the monitor has shifted to the power saving mode, the images on the screen are not displayed.

Attention

• Turning off the main power switch or unplugging the power cord completely shuts off power supply to the monitor.

• Power consumption varies even when the stereo mini jack cable is connected.

Note

• The monitor changes to the power saving mode about 15 seconds after the signal input ceases to be detected.

Procedure

1. Choose “PowerManager” in the Setting menu, and press .

2. Choose “Power Save” in the “PowerManager” menu, and press .

The “Power Save” menu appears.



Power Saving System

Analog Signal Input

This monitor complies with the VESA DPM standard.

PC

On

Powersaving mode

STAND-BY

SUSPENDED

OFF

PowerOff

Monitor

Operating

Powersavingmode

Powersavingmode

Blue

Power Indicator

Orange

Orange

Digital Signal Input

When the external device connected is a PC

This monitor complies with the DVI DMPM standard.

PC

On

Powersavingmode

PowerOff

Monitor

Operating

Powersavingmode

Powersavingmode

When the external device connected is not a PC

PowerOn

PowerOff

Ext. Device Monitor

Operating

Powersavingmode

Blue

Power Indicator

Orange

Orange

Blue

Power Indicator

Orange

32

Chapter4PowerSavingFunctions

Attention

• When all the conditions below are met, the monitor does not change to the power saving mode even if “Power Save” is set to “Enable”:

- “Power Save” for Sound is set to “Sound On” ( “Audio Output” (page 33) )

- In the mute state ( “To mute the sound temporarily” (page 28)

)

In these cases, reset the mute.

Exiting the power saving mode

If the monitor receives input, it automatically exits the power saving mode and returns to the normal display mode.

●

Audio Output

This monitor allows you to turn off the audio output from the speakers/headphone at the power saving mode.

Procedure


2. Choose “Power Save” in the “Sound” menu, and press .

The “Power Save” menu appears.

3. Select “Sound On” or “Sound Off” with or .


Attention

• No audio is output while the monitor is in the Power Saving mode, if the HDMI signal is input or the sound source is of HDMI.

4-2. Setting Power Indicator “Power Indicator”

This function allows you to set the power indicator (blue) ON/OFF in the monitor ON condition.

Procedure


2. Choose “Power Indicator” in the “Monitor Settings” menu, and press .

The “Power Indicator” menu appears.




33

4-3. Enabling/Disabling Automatic Brightness

Adjustment “Auto EcoView”

The sensor on the front side of the monitor detects the environmental brightness to adjust the screen brightness automatically and comfortably by using the Auto EcoView function.

Attention

• Be careful not to block the sensor on the lower side of the monitor when using the Auto EcoView function.

Procedure


The “EcoView” menu appears.

2. Select “On” or “Off” with or .


Note

• As “Brightness” in the Setting menu is changed, the auto adjustment range for Auto EcoView is also changed.

4-4. Checking the power saving level

The EcoView menu allows you to check Power Reduction, CO2 Reduction, and Eco Performance Level. The more indicators light up representing the Eco Performance Level, the higher the power saving level attained.

EcoView Menu

Auto EcoView

Power Reduction

CO2 Reduction

Eco Performance Level

30 W

17 g

On

Indicator

Procedure


The “EcoView” menu appears.

4-5. Enabling/Disabling Auto Power-OFF “Off Timer

(min)”

This function allows you to set the time to power off the monitor automatically.


Disable, 30, 60, 90, 120, 150, 180

Procedure


Each time you press , the set time changes.

34


Canceling Off Timer

1. Press until “Disable” appears.

Checking the remaining time

1. Press when the Off Timer is set.

The time to turn off the power appears.

Extending the time of the Off Timer

1. Press while the remaining time is displayed.

Each time you press , the time is extended.


35

Chapter 5 Connecting Cables

5-1. Connecting Multiple External Devices

The product has multiple connections to external devices and allows you to switch to one of the connections for display.

Attention

• Do not use dual link cables.

Connection examples

HDMIconnector DVI-Dconnector D-Sub connector

Digital

(HDMI)

Digital

(DVI)

Toext.device1

Analog

Signalcable

(MD-C87option)

D-Submini

15-pinconnector

Toext.device2

Signalcable

(suppliedFD-C39)

DVIconnector

Toext.device3,4

HDMIcable

(Commerciallyavailableproduct)

HDMI connector or

DVI-HDMIconvertercable

(Commerciallyavailableproduct)

DVIconnector

●

To switch among input signals

Press or on the remote control to change the input signal.

When the signal is switched, the active input port name appears at the top right corner of the screen.

PC2(D-SUB)

•

Note

on the monitor also can change the input. (see “1-2. Controls and Functions” (page 8)

).

36

Chapter5ConnectingCables

Chapter 6 Troubleshooting

If a problem still remains after applying the suggested remedies, contact your local dealer.

No picture

Problem

1. No picture

• Powerindicatordoesnotlight.

• Powerindicatorislightingblue.

• Powerindicatorislightingorange.

2. The message below appears.

Example:

PC2(D-SUB)

Signal Error

Possible cause and remedy

• Checkwhetherthepowercordisconnectedproperly.

• Turnoffthemainpower,andthenturnitonagaina fewminuteslater.

• Turnthemainpowerswitchon.

• Press monitor).

ontheremotecontrol(or onthe

• Increase“Brightness”,“Contrast”,or“Gain”inthe

Settingmenu(see “Toperformadvancedadjustments”

(page16) ).

• Checkwhetherthesignalcableisconnectedproperly.

• Checkwhethertheexternaldeviceisturnedon.

• Operatethemouseorkeyboard.

• Switchtheinputsignal.

• IfanexternaldeviceispluggedintotheHDMIport, changetheHDCPauthenticationsetting.Poweroff onceandthenpress onthemonitorforfive secondsormoretochangethesettingandthenturn onthepoweragain.(see

“3-8.ChangingtheHDCP authenticationsettingforHDMIsignalinput”(page30) ).

Thismessageappearswhenthesignalisnotinput correctlyevenwhenthemonitorfunctionsproperly.

• Themessageshowsthattheinputsignalisoutofthe specifiedrange.

• Whentheanalogsignal(D-Sub)/digitalsignal(DVI-D,

HDMI:PCsignal)isinput,takethemeasuresbelow:

-CheckwhetherthePCisconfiguredtomeetthe resolutionandverticalscanfrequencyrequirements ofthemonitor(see

“2-1.CompatibleResolutions/

Formats”(page13) ).

-RebootthePC.

-Selectanappropriatedisplaymodeusingthe graphicsboard’sutility.Refertothemanualofthe graphicsboardfordetails.

Chapter6Troubleshooting

37

Imaging problems (for both digital and analog)

Problem

3. The screen is too bright or too dark.

4. Characters are blurred.

5. Afterimages appear.

6. Green/red/blue/white dots or defective dots remain on the screen.

7. Interference patterns or pressure marks remain on the screen.

8. Noise appears on the screen.

9. The screen is whitish or blackish.


• Use“Brightness”or“Contrast”intheSettingmenuto adjustit.(TheLCDmonitorbacklighthasalimitedlife span.Whenthescreenbecomesdarkorbeginsto flicker,contactyourlocaldealer.)

• TurnontheAutoEcoViewfunction.Themonitor detectstheenvironmentalbrightnesstoadjustthe screenbrightnessautomatically.

• CheckwhetherthePCisconfiguredtomeetthe resolutionandverticalscanfrequencyrequirements ofthemonitor(see

“2-1.CompatibleResolutions/

Formats”(page13) ).

• Use“Smoothing”intheSettingmenutoadjustit(see

“Tomodifyblurredcharacters/lines“Smoothing””

(page26)

).

• AfterimagesareparticulartoLCDmonitors.Avoid displayingthesameimageforalongtime.

• Usethescreensaverorpowersavefunctiontoavoid displayingthesameimageforextendedperiodsof time.

• ThisisduetoLCDpanelcharacteristicsandisnota failure.

• Leavethemonitorwithawhiteorblackscreen.The symptommaydisappear.

• IntheSettingmenu,set“Overdrive”to“Off”(see

“To setoverdriveintensity“Overdrive””(page22)

).

• WhenenteringthesignalsofHDCPsystem,the normalimagesmaynotbedisplayedimmediately.

• Use“ColorSpace”ofthe“Screen”submenu(forthe

HDMIinput),“BlackLevel”(see “Toadjustblacklevel

“BlackLevel””(page17) ),and“Contrast”(see

“Toadjust contrast“Contrast””(page18)

)intheSettingmenuto adjustit.

Imaging problems (for digital only)

Problem

10. The color shown on the display is not correct (for HDMI input).

11. The screen flashes (for HDMI input)


• Changethecolorspaceofthevideosignalin“Screen”

-“ColorSpace”undertheSettingmenu.

• Transmittablesignalsdifferonthecategoryofthe

HDMIcable.CheckwhetherthecablesupportHigh

Speed.

38


Imaging problems (for analog only)

Problem

12. Display position is incorrect.

13. Vertical bars appear on the screen or a part of the image is flickering.


• Use“Position”intheSettingmenutocorrectthe imageposition(see

“Tocorrectthescreenposition

“Position””(page25) ).

• Iftheproblempersists,usethegraphicsboard’sutility ifavailabletochangethedisplayposition.

• Use“Clock”intheSettingmenutoadjustit(see “To eliminateverticalbars“Clock””(page24) ).

14. Whole screen is flickering or blurring.

• Use“Phase”intheSettingmenutoadjustit(see “To removeflickeringorblurring“Phase””(page24)

).


39

Other problems

Problem

15. The “Smoothing” on the Setting menu

“Screen” cannot be selected.

16. The auto adjustment function does not work.

17. No audio output.

18. “ScreenManager Pro for LCD (DDC/CI)” does not run.

19. Will not change to the power saving mode


• Youcannotchoose“smoothing”whenthescreenis displayedinthefollowingresolutionsorsettings.

-Theresolutionis1920×1080

-ScreenSizeis“Normal”

• Thisfunctiondoesnotworkduringdigitalsignalinput.

• ThisfunctionisintendedforuseontheMacintosh andonAT-compatiblePCrunningWindows.Itdoes notworkproperlywhenanimageisdisplayedonly onapartofthescreen(commandpromptwindow,for example)orwhenablackbackground(wallpaper,etc.) isinuse.

• Thisfunctiondoesnotworkcorrectlywithsome graphicsboards.

• Checkwhetherthestereominijackcableisconnected properly.

• Checkwhethervolumeissetto0.

• Checkthecurrentexternaldeviceandaudioplayback softwaretoseewhethertheyareconfiguredcorrectly.

• IfHDMIinputisused,checkthecurrentexternal deviceandthe“Source”settingintheSettingmenu

(see

“3-2.SwitchingsoundsourceforHDMIsignal input“Source””(page28) ).

• “ScreenManagerProforLCD(DDC/CI)”doesnotrun whenaPCisconnectedtotheHDMIinput.

• Whenalltheconditionsbelowaremet,themonitor doesnotchangetothepowersavingmodeevenif

“PowerSave”issetto“Enable”:

-“PowerSave”forSoundissetto“SoundOn”( “Audio

Output”(page33)

)

-Inthemutestate(

“Tomutethesoundtemporarily”

(page28)

)

Inthesecases,resetthemute.

40


Chapter 7 Reference

7-1. How to Attach the Optional Arm

An optional arm (or an optional stand) can be attached by removing the stand section. Please refer to our web site for the corresponding optional arm (or optional stand). http://www.eizo.com

Attention

• When attaching an arm or stand, follow the instructions of their user’s manual.

• When using another manufacturer’s arm or stand, confirm the following in advance and select one conforming to the

VESA standard. Use the M4 × 12 mm screws supplied with this product.

- Clearance between the screw holes: 100 mm × 100 mm

- Thickness of plate: 2.6 mm

- Strong enough to support weight of the monitor unit (except the stand) and attachments such as cables.

• When using an arm or stand, attach it to meet the following tilt angles of the monitor.

- Up 45°, down 45° (horizontal display, and vertical display rotated 90 degrees clockwise)

• Connect the cables after attaching an arm or stand.

• The monitor and arm or stand are heavy. Dropping them may result in injury or equipment damage.

Procedure

1.

Lay the LCD monitor on a soft cloth spread over on a stable surface with the panel surface facing down.

2.

Remove the Stand base.

Turn the fixing screws for the Stand base to detach it.

3.

Attach the arm or stand to the monitor.

Secure the monitor to the arm or stand using the screws specified in the user’s manual of the arm or stand.

Chapter7Reference

41

7-2. Attaching the Stand base

The once removed the Stand base can be attached to the monitor again with the following procedures.

Procedure

1.

Lay the LCD monitor on a soft cloth spread over on a stable surface with the panel surface facing down.

2.

Attach the Stand base.

Hold the Stand base with the arrow “ ” facing upward, align the two holes (a) of the Stand base with the two tabs (b) at the bottom of the monitor, and snap the tabs into the holes.

b a

3.

Turn the supplied screw in the “LOCK” direction to lock the Stand base.

Tightenscrew,thenpressknobflat.

7-3. Displaying Monitor Information “Information”

This function allows you to display the model name, serial number, usage time, resolution, and input signal.

Procedure

1. Choose “Information” in the Setting menu, and press .

The “Information” menu appears.

Attention

• The usage time is not always “0” when you purchase the monitor due to factory inspection.

42

Chapter7Reference

7-4. Specifications

LCDPanel

HorizontalScan

Frequency

VerticalScan

Frequency

Size

Type

Surfacetreatment

Surfacehardness

Viewingangles

DotPitch

ResponseTime

Contrastratio

Analog

Digital

Analog

Digital

DVI

HDMI

DVI

23.0-inch(580mm)

TFTcolorLCD,VA

Anti-GlareHardCoating

3H

Viewingangles:Horizontal178°,vertical178°(CR≥10)

0.2655mm

Black-white-black:Approx.25ms

Gray-to-gray:Approx.7ms(Overdrivesetting:Enhanced)

3000:1(whenContrastEnhancersettingis“On”10000:1)

31-81kHz

31-68kHz

15-68kHz

55-76Hz(non-interlace)

59-61Hz(non-interlace)

(VGATEXT:69-71Hz)

Applicablevideosignalformats

Applicableaudiosignalformats

Resolution

Max.DotClock

Max.DisplayColor

DisplayArea(H×V)

PowerSupply

Power

Consumption

HDMI

ScreenDisplayOn

Powersavingmode

49-61Hz(VGATEXT:69-71Hz)

VGA/525i(480i)/525p(480p)/1125i(1080i)/750p(720p)/1125p(1080p):60Hz

625i(576i)/625p(576p)/1125i(1080i)/750p(720p)/1125p(1080p):50Hz

2chlinearPCM(32kHz/44.1kHz/48kHz)

1920Dots×1080Lines

148.5MHz

Approx.16.77millioncolors(1064.33millioncolors/10bitLUT)

509.76mm×286.74mm(20.1inch×11.3inch)

100-120VAC±10%,50/60Hz0.75A

200-240VAC±10%,50/60Hz0.45A

45Worless(Speakerworking)

43Worless(Speakernotworking)

1.0Worless(forD-Subsinglesignalinput,whenstereominijack cableisnotconnected)

0.17Worless

0W

D-Submini15-pin

PowerOff

MainPowerOff

InputSignalConnector

AnalogInputSignal(Sync)

AnalogInputSignal(Video)

DigitalSignalTransmission

Videosignalmemory(Max.)

DVI-Dconnector(ApplicabletoHDCP)

HDMITypeA

*1

×2

Separate,TTL,positive/negative

Analog,Positive(0.7Vp-p/75Ω)

TMDS(SingleLink)

D-Subinput:45types,DVI-Dinput:10types,

HDMI1input:10types,HDMI2input:10types

AudioOutput

LineInput

Speakeroutput:0.5W+0.5W(8Ω,THD+N:1%orless)

Headphoneoutput:2mW+2mW

Inputimpedance:44kΩ(typ.)

Inputlevel:2.0Vrms(Max.)

Plug&Play VESADDC2B/EDIDstructure1.3

*1

HDMICEC(ormutualcontrol)isnotsupported.

Chapter7Reference

43

Dimensions

(Width)×

(Height)×

(Depth)

Mass

Mainunit 549mm(21.6inch)×403mm(15.9inch)×212mm(8.3inch)

Mainunit(withoutstand) 549mm(21.6inch)×393mm(15.5inch)×58mm(2.28inch)

Movablerange

Environmental

Conditions

Mainunit Approx.6.9kg(15.2lbs)

Mainunit(withoutstand) Approx.6.1kg(13.4lbs)

Temperature

Tilt:20°Up,-5°Down

Operating:5°Cto35°C(41°Fto95°F)

Storage:-20°Cto60°C(-4°Fto140°F)

Humidity

AirPressure

Operating:20%to80%R.H.(nocondensation)

Storage:10%to90%R.H.(nocondensation)

Operating:700to1,060hPa

Storage:200to1,060hPa

Main Default Settings

ColorMode

OffTimer

ScreenSize

AutoEcoView

Smoothing

SoundLevel

Sound-PowerSave

PowerManager-PowerSave

DDC/CI

KeyLock

Logo

PowerIndicator

Language

D-Sub/DVI-Dinput:User1

HDMIinput:Game

Disable

D-Sub/DVI-Dinput:Fullscreen

HDMI(PCsignal/HDsignal)input:Fullscreen

HDMI(SDsignal)input:Auto

On

3

0

SoundOff

Enable

Enable

Off

On

Enable

English

44

Chapter7Reference

Outside Dimensions

486(19.1)

171(6.7)

Unit:mm(inch)

18.6 (0.73)

180(7.1)

549(21.6)

511.8(20.1) 18.6

(0.73)

5°

TILT

20°

224.5(8.8) 100(3.9) 224.5(8.8)

57.6 (2.27)

214(8.4)

38 (1.5)

62

(2.44)

212(8.3)

216(8.5)

Accessories

CleaningKit

Signalcable(D-Submini15-pin)

EIZO“ScreenCleaner”

MD-C87

For the latest information about the accessories, refer to our web site.

http://www.eizo.com

Chapter7Reference

45

7-5. Glossary

Clock

The analog signal input monitor needs to reproduce a clock of the same frequency as the dot clock of the graphics system in use, when the analog signal is converted to a digital signal for image display. This is called clock adjustment. If the clock pulse is not set correctly, some vertical bars appear on the screen.

Color Space

Color space is a method to specify and express the color. There are YUV and RGB, etc. YUV expresses the color by using the luminance (Y), the color difference of R (U) and the color difference of blue (V). RGB does it by using the gradation of 3 colors of Red (R, Green (G) and Blue (B).

DDC/CI (Display Data Channel/Command Interface)

VESA provides the standardization for the interactive communication of the setting information, etc. between a PC and the monitor.

DVI (Digital Visual Interface)

DVI is a digital interface standard. DVI allows direct transmission of the PC’s digital data without loss.

This adopts the TMDS transmission system and DVI connectors. There are two types of DVI connectors.

One is a DVI-D connector for digital signal input only. The other is a DVI-I connector for both digital and analog signal inputs.

DVI DMPM (DVI Digital Monitor Power Management)

DVI DMPM is a digital interface power-saving function. The “Monitor ON (operating mode)” and “Active

Off (power-saving mode)” are indispensable for DVI DMPM as the monitor’s power mode.

Gain

This is used to adjust each color parameter for red, green and blue. An LCD monitor displays the color by the light passing through the panel color filter. Red, green and blue are the three primary colors. All the colors on the screen are displayed by combining these three colors. The color tone can be changed by adjusting the light intensity (volume) passing through each color’s filter.

Gamma

Generally, the monitor brightness varies nonlinearly with the input signal level, which is called “Gamma

Characteristic”. A small gamma value produces a low-contrast image, while a large gamma value produces a high-contrast image.

HDCP (High-bandwidth Digital Content Protection)

Digital signal coding system developed to copy-protect the digital contents, such as video, music, etc.

This helps to transmit the digital contents safely by coding the digital contents sent via the DVI or HDMI connector on the output side and decoding them on the input side.

Any digital contents cannot be reproduced if both of the equipments on the output and input sides are not applicable to HDCP system.

46

Chapter7Reference

HDMI (High-Definition Multimedia Interface)

HDMI is a digital interface standard, developed for consumer electrical appliance or AV device. This standard is issued on the basis of the DVI standard which is one of an interface specification for the connection between a PC and a monitor. The projected image, sound and control signal without compressed enable to be transmitted with one cable.

Overdrive

This technology enhances response speed by increasing the potential difference at the time of motion of liquid-crystal pixels, and it is used for liquid-crystal TV sets and others in general. It provides clear-cut three-dimensional display with little image lag, by improving response speed of the intermediate graduation range that frequently appears in moving images.

Phase

Phase means the sampling timing to convert the analog input signal to a digital signal. Phase adjustment is made to adjust the timing. It is recommended that phase adjustment be made after the clock is adjusted correctly.

Range Adjustment

Range adjustment controls the signal output levels to display every color gradation. It is recommended that range adjustment be made before color adjustment.

Resolution

The LCD panel consists of numerous pixels of specified size, which are illuminated to form images. This monitor consists of 1920 horizontal pixels and 1080 vertical pixels. At a resolution of 1920 × 1080, all pixels are illuminated as a full screen (1:1).

sRGB (Standard RGB)

International standard for color reproduction and color space among peripheral devices (such as monitors, printers, digital cameras, scanners). As a form of simple color matching for the Internet, colors can be displayed using tones close to those of the transmission and reception devices.

Temperature

Color temperature is a method to measure the white color tone, generally indicated in degrees Kelvin. The screen becomes reddish at a low temperature, and bluish at a high temperature, like the flame temperature.

5000K: Slightly reddish white

6500K: White referred to as daylight-balanced color

9300K: Slightly bluish white

TMDS (Transition Minimized Differential Signaling)

TMDS is one of the signal transmission methods for the digital interface.

Chapter7Reference

47

VESA DPM (Video Electronics Standards Association - Display Power

Management Signaling)

VESA specifications achieve increased energy efficiency for computer monitors. This involves standardization of signals sent from the computer (graphics board).

DPM defines the status of signals transmitted between the computer and monitor.

7-6. Preset Timing

The following table shows factory preset analog signal timing:

Attention

• Display position may be deviated depending on the PC connected, which may require screen adjustment using Setting menu.

• If a signal other than those listed in the table is input, adjust the screen using the Setting menu. However, screen display may still be incorrect even after the adjustment.

• When interlace signals are used, the screen cannot be displayed correctly even after screen adjustment using the Setting menu.

Resolution

Applicable

Signals

640×480

720×400

640×480

800×600

800×600

1024×768

1024×768

1280×720

VGA/CEA-861

VGATEXT

VESA

VESA

VESA

VESA

VESA

CEA-861

1280×960

1280×1024

1280×1024

1680×1050

VESA

VESA

VESA

VESACVT

1680×1050 VESACVTRB

1920×1080 CEA-861

Dot Clock:

MHz

25.18

28.32

31.50

40.00

49.50

65.00

78.75

74.25

108.00

108.00

135.00

146.25

119.00

148.50

Frequency

Horizontal: kHz

31.47

31.47

37.50

37.88

46.88

48.36

60.02

45.00

60.00

63.98

79.98

65.29

64.67

67.50

Polarity

Vertical: Hz Horizontal Vertical

59.94

70.09

75.00

60.32

75.00

60.00

75.03

60.00

60.00

60.02

75.03

59.95

59.88

60.00

Negative

Negative

Negative

Positive

Positive

Negative

Positive

Positive

Positive

Positive

Positive

Negative

Positive

Positive

Negative

Positive

Negative

Positive

Positive

Negative

Positive

Positive

Positive

Positive

Positive

Positive

Negative

Positive

48

Chapter7Reference

Appendix

Trademark

VESA is a registered trademark or a trademark of the Video Electronics Standards Association in the United

States and other countries.

Windows, Windows Vista, Windows Media, and Xbox 360 are registered trademarks of Microsoft Corporation in the United States and other countries.

Apple, Mac, Macintosh, iMac, eMac, Mac OS, MacBook, PowerBook, ColorSync, QuickTime, and iBook are registered trademarks of Apple Inc.

Acrobat, Adobe, Adobe AIR, and Photoshop are registered trademarks of Adobe Systems Incorporated in the

United States and other countries.

PowerPC is a registered trademark of International Business Machines Corporation.

Pentium is a registered trademark of Intel Corporation in the United States and other countries.

AMD Athlon and AMD Opteron are trademarks of Advanced Micro Devices, Inc.

GRACoL and IDEAlliance are registered trademarks of International Digital Enterprise Alliance.

ColorVision, ColorVision Spyder2 are registered trademarks of DataColor Holding AG.

Spyder3 is a trademark of DataColor Holding AG.

Eye-One, ColorMunki, and X-Rite are registered trademarks or trademarks of X-Rite Incorporated.

TouchWare is a trademark of 3M Touch Systems, Inc.

NextWindow is a registered trademark of NextWindow Ltd.

RealPlayer is a registered trademark of RealNetworks, Inc.

NEC is a registered trademark of NEC Corporation. PC-9801 and PC-9821 are trademarks of NEC

Corporation.

PlayStation is a registered trademark of Sony Computer Entertainment Inc.

PSP and PS3 are trademarks of Sony Computer Entertainment Inc.

ENERGY STAR is a registered trademark of the United States Environmental Protection Agency in the United

States and other countries.

HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of

HDMI Licensing, LLC in the United States and other countries.

EIZO, the EIZO Logo, FlexScan, FORIS, RadiForce, RadiCS, RadiNET, and ScreenManager are registered trademarks of EIZO NANAO CORPORATION in Japan and other countries.

ColorNavigator, EIZO EasyPIX, EcoView NET, EIZO ScreenSlicer, i・Sound, Screen Administrator, UniColor

Pro, and Raptor are trademarks of EIZO NANAO CORPORATION.

All other company and product names are trademarks or registered trademarks of their respective owners.

License

The round gothic bold bit map font used for the characters displayed above this product is designed by Ricoh.

ENERGY STAR

As an ENERGY STAR Partner, EIZO NANAO CORPORATION has determined that this product meets the ENERGY STAR guidelines for energy efficiency.

Appendix

49

TCO

This product has acquired TCO standard that relates to safety, ergonomics, environment and so forth of office equipment. For overview of the TCO, refer to our website.

http://www.eizo.com

FCC Declaration of Conformity

For U.S.A. , Canada, etc. (rated 100-120 Vac) Only

We, the Responsible Party

FCC Declaration of Conformity

EIZONANAOTECHNOLOGIESINC.

5710WarlandDrive,Cypress,CA90630

Phone:(562)431-5011

declare that the product

Tradename:EIZO

Model:FORISFS2331

is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,pursuant toPart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainst harmfulinterferenceinaresidentialinstallation.Thisequipmentgenerates,uses,andcanradiateradio frequencyenergyand,ifnotinstalledandusedinaccordancewiththeinstructions,maycauseharmful interferencetoradiocommunications.However,thereisnoguaranteethatinterferencewillnotoccurin aparticularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradioortelevisionreception, whichcanbedeterminedbyturningtheequipmentoffandon,theuserisencouragedtotrytocorrectthe interferencebyoneormoreofthefollowingmeasures.

* Reorientorrelocatethereceivingantenna.

* Increasetheseparationbetweentheequipmentandreceiver.

* Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.

* Consultthedealeroranexperiencedradio/TVtechnicianforhelp.

Changesormodificationsnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidthe user’sauthoritytooperatetheequipment.

Note

UsetheattachedspecifiedcablebeloworEIZOsignalcablewiththismonitorsoastokeepinterference withinthelimitsofaClassBdigitaldevice.

- ACCord

- ShieldedSignalCable(Enclosed)

Canadian Notice

ThisClassBdigitalapparatuscomplieswithCanadianICES-003.

CetappareilnumériquedeleclasseBestcomformeàlanormeNMB-003duCanada.

50

Appendix

Hinweise zur Auswahl des richtigen Schwenkarms für Ihren Monitor

Dieser Monitor ist für Bildschirmarbeitsplätze vorgesehen. Wenn nicht der zum Standardzubehör gehörige

Schwenkarm verwendet wird, muss statt dessen ein geeigneter anderer Schwenkarm installiert werden. Bei der

Auswahl des Schwenkarms sind die nachstehenden Hinweise zu berücksichtigen:

Der Standfuß muß den nachfolgenden Anforderungen entsprechen: a) Der Standfuß muß eine ausreichende mechanische Stabilität zur Aufnahme des Gewichtes vom Bildschirmgerät und des spezifi zierten Zubehörs besitzen. Das Gewicht des Bildschirmgerätes und des Zubehörs sind in der zugehörenden Bedienungsanleitung angegeben.

b) Die Befestigung des Standfusses muß derart erfolgen, daß die oberste Zeile der Bildschirmanzeige nicht höher als die Augenhöhe eines Benutzers in sitzender Position ist.

c) Im Fall eines stehenden Benutzers muß die Befestigung des Bildschirmgerätes derart erfolgen, daß die Höhe der

Bildschirmmitte über dem Boden zwischen 135 – 150 cm beträgt.

d) Der Standfuß muß die Möglichkeit zur Neigung des Bildschirmgerätes besitzen (max. vorwärts: 5°, min. nach hinten ≥ 5°).

e) Der Standfuß muß die Möglichkeit zur Drehung des Bildschirmgerätes besitzen (max. ±180°). Der maximale

Kraftaufwand dafür muß weniger als 100 N betragen.

f) Der Standfuß muß in der Stellung verharren, in die er manuell bewegt wurde.

g) Der Glanzgrad des Standfusses muß weniger als 20 Glanzeinheiten betragen (seidenmatt).

h) Der Standfuß mit Bildschirmgerät muß bei einer Neigung von bis zu 10° aus der normalen aufrechten Position kippsicher sein.

Hinweis zur Ergonomie :

Dieser Monitor erfüllt die Anforderungen an die Ergonomie nach EK1-ITB2000 mit dem Videosignal, 1920 ×

1080, Digital Eingang und mindestens 60,0 Hz Bildwiederholfrequenz, non interlaced. Weiterhin wird aus ergonomischen Gründen empfohlen, die Grundfarbe Blau nicht auf dunklem Untergrund zu verwenden (schlechte

Erkennbarkeit, Augenbelastung bei zu geringem Zeichenkontrast.)

Übermäßiger Schalldruck von Ohrhörern bzw. Kopfhörern kann einen Hörverlust bewirken.

Eine Einstellung des Equalizers auf Maximalwerte erhöht die Ausgangsspannung am Ohrhörer- bzw.

Kopfhörerausgang und damit auch den Schalldruckpegel.

„Maschinenlärminformations-Verordnung 3. GPSGV:

Der höchste Schalldruckpegel beträgt 70 dB(A) oder weniger gemäss EN ISO 7779“

[Begrenzung des maximalen Schalldruckpegels am Ohr]

Bildschirmgeräte: Größte Ausgangsspannung 150 mV

Appendix

51

LIMITED WARRANTY

LIMITED WARRANTY

EIZONANAOCORPORATION(hereinafterreferredtoas“ EIZO”)anddistributorsauthorizedbyEIZO(hereinafter referredtoasthe“ Distributors”)warrant,subjecttoandinaccordancewiththetermsofthislimitedwarranty(hereinafter referredtoasthe“ Warranty”),totheoriginalpurchaser(hereinafterreferredtoasthe“Original Purchaser”)who purchasedtheproductspecifiedinthisdocument(hereinafterreferredtoasthe“ Product”)fromEIZOorDistributors, thatEIZOandDistributorsshall,attheirsolediscretion,eitherrepairorreplacetheProductatnochargeiftheOriginal

PurchaserbecomesawarewithintheWarrantyPeriod(definedbelow)thattheProductmalfunctionsorisdamagedinthe courseofnormaluseoftheProductinaccordancewiththedescriptionintheinstructionmanualattachedtotheProduct

(hereinafterreferredtoasthe“ User’s Manual”).

TheperiodofthisWarrantyislimitedto(i)five(5)yearsfromthedateofpurchaseoftheProduct;or,limitedtothe expirationof(ii)30,000hoursofitsuseoftheProduct(hereinafterreferredtoasthe“WarrantyPeriod”);provided, however,thattheWarrantyPeriodfortheLCDpaneloftheProductislimitedtothree(3)yearsfromthedateofpurchase oftheProduct.EIZOandDistributorsshallbearnoliabilityorobligationwithregardtotheProductinrelationtothe

OriginalPurchaseroranythirdpartiesotherthanasprovidedunderthisWarranty.

EIZOandDistributorswillceasetoholdorstoreanypartsoftheProductuponexpirationofseven(7)yearsafterthe productionofsuchpartsisdiscontinued.Inrepairingthemonitor,EIZOandDistributorswilluserenewalpartswhich complywithourQCstandards.

TheWarrantyisvalidonlyinthecountriesorterritorieswheretheDistributorsarelocated.TheWarrantydoesnotrestrict anylegalrightsoftheOriginalPurchaser.

NotwithstandinganyotherprovisionofthisWarranty,EIZOandDistributorsshallhavenoobligationunderthisWarranty whatsoeverinanyofthecasesassetforthbelow:

(a) AnydefectoftheProductcausedbyfreightdamage,modification,alteration,abuse,misuse,accident,incorrect installation,disaster,faultymaintenanceand/orimproperrepairbythirdpartyotherthanEIZOandDistributors;

(b) AnyincompatibilityoftheProductduetopossibletechnicalinnovationsand/orregulations;

(c) AnydeteriorationofdisplayperformancecausedbythedeteriorationofexpendablepartssuchastheLCDpanel and/orbacklight,etc.(e.g.changesinbrightness,changesinbrightnessuniformity,changesincolor,changesin coloruniformity,defectsinpixelsincludingburntpixels,etc.);

(d) AnydefectoftheProductcausedbyexternalequipment;

(e) AnydefectoftheProductonwhichtheoriginalserialnumberhasbeenalteredorremoved;

(f) AnydefectoftheProductcausedbyliquidleakingfrombattery;

(g) Anynormaldeteriorationoftheproduct,particularlythatofconsumables,accessories,and/orattachments(e.g. batteries,buttons,rotatingparts,remotecontrol,cables,User’sManual,etc.);and

(h) Anydeformation,discoloration,and/orwarpoftheexterioroftheproductincludingthatofthesurfaceoftheLCD panel.

ToobtainserviceundertheWarranty,theOriginalPurchasermustdelivertheProduct,freightprepaid,initsoriginal packageorotheradequatepackageaffordinganequaldegreeofprotection,assumingtheriskofdamageand/orloss intransit,tothelocalDistributor.TheOriginalPurchasermustpresentproofofpurchaseoftheProductandthedateof suchpurchasewhenrequestingservicesundertheWarranty.

TheWarrantyPeriodforanyreplacedand/orrepairedproductunderthisWarrantyshallexpireattheendoftheoriginal

WarrantyPeriod.

EIZOORDISTRIBUTORSARENOTRESPONSIBLEFORANYDAMAGETO,ORLOSSOF,DATAOROTHER

INFORMATIONSTOREDINANYMEDIAORANYPARTOFANYPRODUCTRETURNEDTOEIZOORDISTRIBUTORS

FORREPAIR.

EIZOANDDISTRIBUTORSMAKENOFURTHERWARRANTIES,EXPRESSEDORIMPLIED,WITHRESPECTTO

THEPRODUCTANDITSQUALITY,PERFORMANCE,MERCHANTABILITYORFITNESSFORANYPARTICULAR

USE.INNOEVENTSHALLEIZOORDISTRIBUTORSBELIABLEFORANYINCIDENTAL,INDIRECT,SPECIAL,

CONSEQUENTIALOROTHERDAMAGEWHATSOEVER(INCLUDING,WITHOUTLIMITATION,DAMAGESFOR

LOSSOFPROFIT,BUSINESSINTERRUPTION,LOSSOFBUSINESSINFORMATION,ORANYOTHERPECUNIARY

LOSS)ARISINGOUTOFTHEUSEORINABILITYTOUSETHEPRODUCTORINANYCONNECTIONWITHTHE

PRODUCT,WHETHERBASEDONCONTRACT,TORT,NEGLIGENCE,STRICTLIABILITYOROTHERWISE,EVEN

IFEIZOORDISTRIBUTORSHAVEBEENADVISEDOFTHEPOSSIBILITYOFSUCHDAMAGES.THISEXCLUSION

ALSOINCLUDESANYLIABILITYWHICHMAYARISEOUTOFTHIRDPARTYCLAIMSAGAINSTTHEORIGINAL

PURCHASER.THEESSENCEOFTHISPROVISIONISTOLIMITTHEPOTENTIALLIABILITYOFEIZOAND

DISTRIBUTORSARISINGOUTOFTHISLIMITEDWARRANTYAND/ORSALES.

52

Appendix

BEGRENZTE GARANTIE

EIZONANAOCORPORATION(imWeiterenals„ EIZO“bezeichnet)unddieVertragsimporteurevonEIZO(imWeiteren als„ Vertrieb(e)“bezeichnet)garantierendemursprünglichenKäufer(imWeiterenals„Erstkäufer“bezeichnet),der dasindiesemDokumentvorgegebeneProdukt(imWeiterenals„ Produkt“bezeichnet)vonEIZOodereinemVertrieb erworbenhat,gemäßdenBedingungendieserbeschränktenGarantie(imWeiterenals„ Garantie“bezeichnet),dass

EIZOundderVertriebnacheigenemErmessendasProduktentwederkostenlosreparierenoderaustauschen,falls derErstkäuferinnerhalbderGarantiefrist(weiteruntenfestgelegt)eineFehlfunktionbzw.BeschädigungdesProdukts feststellt,diewährenddesnormalenGebrauchsdesProduktsgemäßdenAnweisungendeszumLieferumfangdes

ProduktsgehörendenBenutzerhandbuchs(imWeiterenals„ Benutzerhandbuch“bezeichnet)aufgetretenist.

DieDauerderGarantieleistungbeträgt(i)fünf(5)JahreabdemErstverkaufsdatumdesProduktsoder(ii)30.000

BetriebsstundendesProdukts(imWeiterenals„ Garantiefrist“bezeichnet);dieGarantiefristfürdasLCD-Paneldes

Produktsistjedochaufdrei(3)JahreabdemErstverkaufsdatumdesProduktsbeschränkt.EIZOunddieVertriebe

übernehmenüberdenRahmendieserGarantiehinaushinsichtlichdesProduktskeinerleiHaftungoderVerpflichtung demErstkäuferoderDrittengegenüber.

EIZOunddieVertriebeverpflichtensich,ErsatzteilefürdasProduktübereinenZeitraumvonsieben(7)Jahrennach

EinstellungderProduktionderErsatzteilezulagernbzw.anzubieten.EIZOundseineVertriebspartnerverpflichtensich, beieineretwaigenReparaturdesMonitorsausschließlichProduktegemäßdenEIZO-Qualitätssicherungsstandardszu verwenden.

Diese Garantie gilt nur in Ländern oder Gebieten, in denen sich Vertriebe befinden. Die gesetzlichen

GewährleistungsrechtedesErstkäufersgegenüberdemVerkäuferwerdendurchdieseGarantienichtberührt.

EIZOunddieVertriebebesitzenimRahmendieserGarantiekeinerleiVerpflichtungindenfolgendenFällen:

(a) Produktdefekte,dieaufFrachtschäden,Modifikation,Nachgestaltung,Missbrauch,Fehlbedienung,Unfälle, unsachgemäßeInstallation,Naturkatastrophen,fehlerhafteWartungund/oderunsachgemäßeReparaturdurcheine andereParteialsEIZOunddieVertriebezurückzuführensind.

(b) EineInkompatibilitätdesProduktsaufgrundvontechnischenNeuerungenund/oderneuenBestimmungen,die nachdemKaufinKrafttreten.

(c) JeglicheVerschlechterungderBildschirmleistung,diedurchVerschleißteilewiedasLCD-Panelund/oderdie

Hintergrundbeleuchtungusw.hervorgerufenwerden(z.B.VeränderungenvonHelligkeitoderHelligkeitsverteilung,

VeränderungenvonFarbeoderFarbverteilung,PixeldefekteeinschließlichvondurchgebranntenPixelnusw.).

(d) Produktdefekte,diedurchexterneGeräteverursachtwerden.

(e) JeglicherDefekteinesProdukts,dessenursprünglicheSeriennummergeändertoderentferntwurde.

(f) Produktdefekte,diedurchAustrittvonBatterieflüssigkeitverursachtwerden.

(g) NormaleAbnutzungdesProdukts,insbesonderevonVerbrauchsteilen,Zubehörteilenund/oderBeilagen(z.B.

Batterien,Tasten,drehbareTeile,Fernbedienung,Kabel,Benutzerhandbuchusw.);sowie

(h) Verformungen,Verfärbungenund/oderVerziehungenamProduktäußeren,einschließlichderOberflächedesLCD-

Panels.

BeiInanspruchnahmederGarantieleistungistderErstkäuferverpflichtet,dasProduktaufeigeneKostenund inderOriginalverpackungbzw.eineranderengeeignetenVerpackung,dieeinengleichwertigenSchutzgegen

Transportschädenbietet,andenörtlichenVertriebzuübersenden,wobeiderErstkäuferdasTransportrisikogegenüber

Schädenund/oderVerlustträgt.ZumZeitpunktderInanspruchnahmederGarantieleistungmussderErstkäufereinen

Verkaufsbelegvorweisen,aufdemdasKaufdatumangegebenist.

DieGarantiefristfüreinimRahmendieserGarantieausgetauschtesund/oderrepariertesProdukterlischtnachAblauf derursprünglichenGarantiefrist.

EIZOODERDIEEIZO-VERTRAGSIMPORTEUREHAFTENNICHTFÜRZERSTÖRTEDATENBESTÄNDEODERDIE

KOSTENDERWIEDERBESCHAFFUNGDIESERDATENBESTÄNDEAUFJEGLICHENDATENTRÄGERNODER

TEILENDESPRODUKTS,DIEIMRAHMENDERGARANTIEBEIEIZOODERDENEIZO-VERTRAGSIMPORTEUREN

ZURREPARATUREINGEREICHTWURDEN.

EIZO UND DIE EIZO-VERTRAGSIMPORTEURE GEBEN WEDER EXPLIZITE NOCH IMPLIZITE GARANTIEN

INBEZUGAUFDIESESPRODUKTUNDSEINEQUALITÄT,LEISTUNG,VERKÄUFLICHKEITODEREIGNUNG

FÜREINENBESTIMMTENZWECK.AUFKEINENFALLSINDEIZOODERDIEEIZO-VERTRAGSIMPORTEURE

VERANTWORTLICHFÜRJEGLICHEZUFÄLLIGE,INDIREKTE,SPEZIELLE,FOLGE-ODERANDERESCHÄDEN

JEGLICHERART(EINSCHLIESSLICHOHNEJEDEBEGRENZUNGSCHÄDENBEZÜGLICHPROFITVERLUST,

GESCHÄFTSUNTERBRECHUNG, VERLUST VON GESCHÄFTSINFORMATION ODER JEGLICHEANDEREN

FINANZIELLENEINBUSSEN),DIEDURCHDIEVERWENDUNGDESPRODUKTESODERDIEUNFÄHIGKEIT

ZUR VERWENDUNG DES PRODUKTES ODER IN JEGLICHER BEZIEHUNG MIT DEM PRODUKT, SEI ES

BASIERENDAUFVERTRAG,SCHADENSERSATZ,NACHLAESSIGKEIT,STRIKTEHAFTPFLICHTODERANDEREN

FORDERUNGENENTSTEHEN,AUCHWENNEIZOUNDDIEEIZO-VERTRAGSIMPORTEUREIMVORAUSÜBER

DIEMÖGLICHKEITSOLCHERSCHÄDENINFORMIERTWURDEN.DIESERAUSSCHLUSSENTHÄLTAUCHJEDE

HAFTPFLICHT,DIEAUSFORDERUNGENDRITTERGEGENDENERSTKÄUFERENTSTEHENKANN.ZWECK

DIESERKLAUSELISTES,DIEHAFTUNGVONEIZOUNDDENVERTRIEBENGEGENÜBERFORDERUNGENZU

BEGRENZEN,DIEAUSDIESERBESCHRÄNKTENGARANTIEUND/ODERDEMVERKAUFENTSTEHENKÖNNEN.

Appendix

53

GARANTIE LIMITÉE

EIZONANAOCORPORATION(ci-aprèsdénommé« EIZO »)etlesdistributeursautorisésparEIZO(ci-aprèsdénommés

« Distributeurs »),sousréserveetconformémentauxtermesdecettegarantielimitée(ci-aprèsdénommée«Garantie

»),garantissentàl’acheteurinitial(ci-aprèsdénommé« Acheteur initial »)duproduitspécifiédanslaprésente(ci-après dénommé« Produit »)achetéauprèsd’EIZOoudeDistributeursagréésEIZO,queEIZOetsesDistributeursauront pouroptionderéparerouremplacergratuitementleProduitsil’Acheteurinitialconstate,pendantlaPériodedegarantie

(définieci-dessous),qu’ilyaundysfonctionnementouqueleProduitasubiundommagedanslecadred’uneutilisation normaleduProduitconformémentàladescriptiondumoded’emploiquiaccompagneleProduit(ci-aprèsdénommé«

Manuel d’utilisation »).

LapériodedecetteGarantieestlimitéeà(i)cinq(5)ansàpartirdeladated’achatduProduitouà(ii)30000heures d’utilisationduProduit(ci-aprèsdénommée« Période de Garantie »),sousréserve,toutefois,quelaPériodede

GarantiedupanneauLCDduProduitestlimitéeàtrois(3)ansàpartirdeladated’achatduProduit.EIZOetses

DistributeursdéclinenttouteresponsabilitéouobligationconcernantceProduitfaceàl’Acheteurinitialouàtouteautre personneàl’exceptiondecellesstipuléesdanslaprésenteGarantie.

EIZOetsesDistributeurscesserontdetenirouconserverenstocktoutepiècedeceProduitaprèsl’expirationde lapériodedesept(7)anssuivantl’arrêtdelaproductiondetellespièces.Pourréparerlemoniteur,EIZOetses distributeursutiliserontdespiècesderechangeconformesànosnormesdecontrôlequalité.

LaGarantieestvalableuniquementdanslespaysoulesterritoiresoùsetrouventlesDistributeurs.LaGarantienelimite aucundesdroitsreconnusparlaloiàl’Acheteurinitial.

NonobstanttouteautreclausedecetteGarantie,EIZOetsesDistributeursn’aurontd’obligationdanslecadredecette

Garantiepouraucundescasénumérésci-dessous:

(a) ToutdéfautduProduitrésultantdedommagesoccasionnéslorsdutransport,d’unemodification,d’unealtération, d’unabus,d’unemauvaiseutilisation,d’unaccident,d’uneinstallationincorrecte,d’undésastre,d’unentretienet/ oud’uneréparationincorrectseffectuésparunepersonneautrequeEIZOousesDistributeurs;

(b) TouteincompatibilitéduProduitrésultantd’améliorationstechniqueset/ouréglementationspossibles;

(c) Toutedétériorationdesperformancesd’affichagecauséeparladétériorationdesélémentsconsommablestels quelepanneauLCDet/oulerétroéclairage,etc.(parexempledeschangementsdeluminosité,deschangements del’uniformitédelaluminosité,desmodificationsdecouleur,deschangementsdel’uniformitédescouleurs,des défectuositésdepixelsycomprisdespixelsbrûlés,etc.);

(d) ToutdéfautduProduitcauséparunappareilexterne;

(e) Toutdéfautd’unProduitsurlequellenumérodesérieoriginalaétéaltéréousupprimé;

(f) ToutdéfautduProduitcauséparunécoulementduliquidecontenudanslespiles;

(g) ToutedétériorationnormaleduProduit,particulièrementcelledesconsommables,desaccessoireset/oudes piècesreliéesauProduit(piles,touches,élémentspivotants,télécommande,câbles,Manueld’utilisationetc.),et

(h) Toutedéformation,décoloration,et/ougondolagedel’extérieurduProduit,ycompriscelledelasurfacedu panneauLCD.

Pourbénéficierd’unservicedanslecadredecetteGarantie,l’AcheteurinitialdoitrenvoyerleProduitportpayé,dans sonemballaged’origineoutoutautreemballageappropriéoffrantundegrédeprotectionéquivalent,auDistributeurlocal, etassumeralaresponsabilitédesdommageset/oupertepossibleslorsdutransport.L’Acheteurinitialdoitprésenterune preuved’achatduProduitcomprenantsadated’achatpourbénéficierdeceservicedanslecadredelaGarantie.

LaPériodedegarantiepourtoutProduitremplacéet/ouréparédanslecadredecetteGarantieexpireraàlafindela

Périodedegarantieinitiale.

EIZOOUSESDISTRIBUTEURSNESAURAIENTÊTRETENUSRESPONSABLESDESDOMMAGESOUPERTESDE

DONNÉESOUD’AUTRESINFORMATIONSSTOCKÉESDANSUNMÉDIAQUELCONQUEOUUNEAUTREPARTIE

DUPRODUITRENVOYÉÀEIZOOUAUXDISTRIBUTEURSPOURRÉPARATION.

AUCUNEAUTREGARANTIE,EXPLICITEOUTACITE,N’ESTOFFERTEPAREIZOETSESDISTRIBUTEURS

CONCERNANTLEPRODUITETSESQUALITÉS,PERFORMANCES,QUALITÉMARCHANDEOUADAPTATION

ÀUNUSAGEPARTICULIER.ENAUCUNCAS,EIZOOUSESDISTRIBUTEURSNESERONTRESPONSABLES

DES DOMMAGES FORTUITS, INDIRECTS, SPÉCIAUX, INDUITS, OU DETOUTAUTRE DOMMAGE QUEL

QU’ILSOIT(YCOMPRIS,SANSLIMITATION,LESDOMMAGESRÉSULTANTD’UNEPERTEDEPROFIT,D’UNE

INTERRUPTIOND’ACTIVITÉS,D’UNEPERTEDEDONNÉESCOMMERCIALES,OUDETOUTAUTREMANQUE

ÀGAGNER)RÉSULTANTDEL’UTILISATIONOUDEL’INCAPACITÉD’UTILISERLEPRODUITOUAYANTUN

RAPPORTQUELCONQUEAVECLEPRODUIT,QUECESOITSURLABASED’UNCONTRAT,D’UNTORT,D’UNE

NÉGLIGENCE,D’UNERESPONSABILITÉSTRICTEOUAUTRE,MÊMESIEIZOOUSESDISTRIBUTEURSONTÉTÉ

AVERTISDELAPOSSIBILITÉDETELSDOMMAGES.CETTELIMITATIONINCLUTAUSSITOUTERESPONSABILITÉ

QUIPOURRAITÊTRESOULEVÉELORSDESRÉCLAMATIONSD’UNTIERSCONTREL’ACHETEURINITIAL.

L’ESSENCEDECETTECLAUSEESTDELIMITERLARESPONSABILITÉPOTENTIELLEDEEIZOETDESES

DISTRIBUTEURSRÉSULTANTDECETTEGARANTIELIMITÉEET/OUDESVENTES.

54

Appendix

GARANTÍA LIMITADA

EIZO NANAO CORPORATION (en lo sucesivo “ EIZO”) y sus distribuidores autorizados (en lo sucesivo los

“ Distribuidores”),conarregloydeconformidadconlostérminosdeestagarantíalimitada(enlosucesivola“Garantía”), garantizanalcompradororiginal(enlosucesivoel“ Comprador original”)quecompróelproductoespecificadoeneste documento(enlosucesivoel“ Producto”)aEIZOoasusDistribuidores,queEIZOysusDistribuidores,asupropio criterio,repararánosustituiránelProductodeformagratuitasielCompradororiginaldetectadentrodelperiododela

Garantía(indicadoposteriormente)queelProductonofuncionacorrectamenteoquesehaaveriadoduranteeluso normaldelmismodeacuerdoconlasindicacionesdelmanualdeinstruccionessuministradoconelProducto(enlo sucesivoel“ Manual del usuario”).

ElperíododevalidezdeestaGarantíaestálimitadoa(i)cinco(5)añosapartirdelafechadecompradelProductoo

(ii)a30.000horasdeusodelProducto(enadelantedesignadocomoel“ Periodo de Garantía”);conlaexclusión,no obstante,dequeelperíododegarantíadelpanelLCDdelProductoestálimitadoatres(3)añosapartirdelafecha decompradelProducto.EIZOysusDistribuidoresnotendránningunaresponsabilidadniobligaciónconrespectoal

ProductoparaconelCompradororiginalnicontercerosquenoseanlasestipuladasenlapresenteGarantía.

EIZOysusDistribuidoresnoestaránobligadosasuministrarcualquierrecambiodelProductounavezpasadossiete

(7)añosdesdequesedejedefabricarelmismo.Paralareparacióndelmonitor,EIZOylosdistribuidoresutilizarán repuestosquecumplanconnuestrosestándaresdecontroldecalidad.

LaGarantíaesválidasóloenlospaísesyterritoriosdondeestánubicadoslosDistribuidores.LaGarantíanorestringe ningúnderecholegaldelCompradororiginal.

ApesardelasestipulacionesdeestaGarantía,EIZOysusDistribuidoresnotendránobligaciónalgunabajoesta

Garantíaenningunodeloscasosexpuestosacontinuación:

(a) CualquierdefectodelProductocausadopordañoseneltransporte,modificación,alteración,abuso,usoincorrecto, accidente,instalaciónincorrecta,desastre,mantenimientoincorrectoy/oreparaciónindebidarealizadaporun terceroquenoseaEIZOosusDistribuidores.

(b) CualquierincompatibilidaddelProductodebidaaposiblesinnovacionestécnicasy/oreglamentaciones.

(c) Cualquierdeterioroenelrendimientodelavisualizacióncausadoporfallosenlaspiezasconsumiblescomoel panelLCDy/ola"Backlight",etc.(p.ej.cambiosdebrillo,cambiosdeuniformidaddelbrillo,cambiosdecolor, cambiosdeuniformidaddelcolor,defectosdepíxeles,incluyendopíxelesmuertos,etc.).

(d) CualquierdefectodelProductocausadoporunequipoexterno.

(e) CualquierdefectodelProductoenelquehayasidoalteradooborradoelnúmerodeserieoriginal.

(f) CualquierdefectodelProductocasusadoporfugasdelíquidodelaspilas.

(g) CualquierdeterioronormaldelProducto,yenparticulardelaspiezasconsumibles,accesoriosydemás(p.ej. pilas,botones,piezasgiratorias,mandoadistancia,cables,Manualdelusuario,etc.).

(h) Cualquierdeformación,decoloracióny/oalabeodelexteriordelProductoincluidalasuperficiedelpanelLCD.

ParaobtenerservicioenlostérminosdeestaGarantía,elProductodeberáserenviadoporelCompradororiginal, asuDistribuidorlocal,coneltransportepreviamentepagado,enelembalajeoriginaluotroembalajeadecuadoque ofrezcaelmismogradodeprotección,asumiendoelriesgodedañosy/opérdidadelProductoduranteeltransporte.El

CompradororiginaldeberápresentaruncomprobantedecompradelProductoenelquesereflejelafechadecompra delmismocuandolosoliciteelserviciodeGarantía.

ElPeriododegarantíaparacualquierProductoreemplazadoy/oreparadoenlostérminosdeestaGarantíaexpiraráal vencerelPeriododegarantíaoriginal.

EIZOOLOSDISTRIBUIDORESAUTORIZADOSDEEIZONOSERESPONSABILIZANDENINGÚNDAÑOO

PÉRDIDAQUEPUEDANSUFRIRLOSDATOSUOTRAINFORMACIÓNALMACENADAENCUALQUIERMEDIOO

CUALQUIERPARTEDECUALQUIERPRODUCTODEVUELTOAEIZOOALOSDISTRIBUIDORESDEEIZOPARA

SUREPARACIÓN.

EIZOYLOSDISTRIBUIDORESAUTORIZADOSDEEIZONOOFRECENNINGUNAOTRAGARANTÍA,IMPLÍCITA

NI EXPLÍCITA, CON RESPECTOAL PRODUCTOYA SU CALIDAD, RENDIMIENTO, COMERCIABILIDAD E

IDONEIDADPARACUALQUIERUSOENPARTICULAR.ENNINGÚNCASOSERÁNEIZOOLOSDISTRIBUIDORES

AUTORIZADOSDEEIZORESPONSABLESDENINGÚNDAÑOEMERGENTE,INDIRECTO,ESPECIAL,INHERENTE

OCUALQUIERAQUESEA(INCLUYENDO,SINLIMITACIÓN,DAÑOSPORLUCROCESANTE,INTERRUPCIÓN

DELAACTIVIDADCOMERCIAL,PÉRDIDADEINFORMACIÓNCOMERCIALOCUALQUIEROTRAPÉRDIDA

PECUNIARIA)QUESEDERIVEDELUSOOIMPOSIBILIDADDEUSODELPRODUCTOOENRELACIÓNCONEL

PRODUCTO,YASEABASADOENCONTRATO,PORAGRAVIO,NEGLIGENCIA,ESTRICTARESPONSABILIDAD

OCUALQUIERAQUESEA,AUNCUANDOSEHAYAADVERTIDOAEIZOOALOSDISTRIBUIDORESDEEIZO

DELAPOSIBILIDADDETALESDAÑOS.ESTAEXCLUSIÓNTAMBIÉNABARCACUALQUIERRESPONSABILIDAD

QUE PUEDA DERIVARSE DE RECLAMACIONES HECHAS POR UNTERCERO CONTRA EL COMPRADOR

ORIGINAL.LAESENCIADEESTAESTIPULACIÓNESLIMITARLARESPONSABILIDADPOTENCIALDEEIZOYLOS

DISTRIBUIDORESQUEPUDIERADERIVARSEDEESTAGARANTÍALIMITADAY/OVENTAS.

Appendix

55

GARANZIA LIMITATA

EIZONANAOCORPORATION(acuisifaràriferimentodaquiinpoicon“ EIZO”)ediDistributoriautorizzatidaEIZO(a cuisifaràriferimentodaquiinpoicon“ Distributori”)garantiscono,secondoiterminidiquestagaranzialimitata(acuisi faràriferimentodaquiinpoicon“ Garanzia”)all’acquirenteoriginale(acuisifaràriferimentodaquiinpoicon“Acquirente

originale”)chehaacquistatoilprodottospecificatoinquestodocumento(acuisifaràriferimentodaquiinpoicon

“ Prodotto”)daEIZOodaisuoiDistributori,cheEIZOeidistributori,alorodiscrezione,riparerannoosostituirannoil

Prodottosenzaaddebitosel’Acquirenteoriginaletrova,entroilperiododellaGaranzia(definitosotto),cheilProdotto malfunzionaesièdanneggiatonelcorsodelsuonormaleutilizzoosservandoleindicazionidelmanualediistruzioni allegatoalProdotto(acuisifaràriferimentodaquiinpoicon“ Manuale utente”).

LapresenteGaranziaèlimitatoa(i)cinque(5)anniapartiredalladatad'acquistodelProdotto;o,limitato(ii)allo scaderedi30.000ored'utilizzodelProdotto(acuisifaràriferimentodaquiinpoicon“ Periodo di Garanzia”);tenendo peròpresentecheilPeriododigaranziadelpannelloLCDdelProdottoèlimitatoatre(3)annidalladatad'acquisto delProdotto.EIZOeisuoiDistributorinonsiassumonoalcunaresponsabilitàenonhannoalcunobbligoriguardoal

Prodottoversol’AcquirenteoriginaleoterzidiversidaquellirelativiaquestaGaranzia.

EIZOeisuoiDistributoricesserannoditenereodiconservarequalsiasiricambiodelProdottoalloscaderedisette

(7)annidopochelaproduzioneditaliricambièstataterminata.Perlariparazionedelmonitor,EIZOeiDistributori utilizzerannopartidiricambioconformiainostristandarddicontrollodellaqualità.

LaGaranziaèvalidasoltantoneipaesidovecisonoiDistributoriEIZO.LaGaranzianonlimitaalcundirittolegale dell’Acquirenteoriginale.

IndipendentementedaqualsiasialtracondizionediquestaGaranzia,EIZOeisuoiDistributorinonavrannoalcunobbligo derivantedaquestaGaranziainognunodeicasielencatidiseguito:

(a) QualsiasidifettodelProdottocausatodadanniditrasporto,modifiche,alterazioni,abusi,usiimpropri,incidenti, installazioneerrata,calamità,manutenzioneerratae/oriparazioniimproprieeseguitedaterzepartichenonsiano

EIZOoisuoiDistributori.

(b) QualsiasiincompatibilitàdelProdottodovutaapossibiliinnovazionitecnichee/onormative.

(c) Qualsiasideterioramentodelleprestazionidelloschermocausatodaldeterioramentodelleparticonsumabili,come ilpannelloLCDe/olaretroilluminazione,ecc.(peresempio:icambiamentidiluminosità,cambiamentidiuniformità dellaluminosità,icambiamentidicolore,icambiamentidiuniformitàdelcolore,idifettideipixel,inclusiipixel bruciati,ecc.).

(d) QualsiasidifettodelProdottocausatodaapparecchiatureesterne.

(e) QualsiasidifettodelProdottoincuiilnumerodiserieoriginalesiastatoalteratoorimosso.

(f) QualsiasidifettodelProdottocausatodallafuoriuscitadiliquidodallepile.

(g) QualsiasinormaledeterioramentodelProdotto,inparticolarmodonellesuepartidiconsumo,accessori,e/o attacchi(peresempio:pile,tasti,partirotanti,telecomando,cavi,Manualedell’utente,ecc.).

(h) Qualsiasitipodideformazione,scolorimento,e/odiinvolucroesternodelProdottoinclusalasuperficiedelpannello

LCD.

PerricevereassistenzatecnicaconquestaGaranzia,l’AcquirenteoriginaledeveinviareilProdotto,contrasporto pre-pagato,nellasuaconfezioneoriginaleoaltraconfezioneadeguatachefornisceunlivelloanalogodiprotezione, assumendosiilrischiodidannie/operditaintransito,alDistributorelocale.L’Acquirenteoriginaledevepresentarela provadiacquistochestabilisceladatadiacquistodelProdottoquandorichiedeserviziosottoGaranzia.

IlPeriododigaranziaperqualsiasiProdottosostituitoe/oriparatosottoquestaGaranziascadeallafinedelPeriododi garanziaoriginale.

EIZOOISUOIDISTRIBUTORINONSONORESPONSABILIPERQUALSIASIDANNOOPERDITADIDATIOALTRE

INFORMAZIONIMEMORIZZATISUQUALSIASISUPPORTOOQUALSIASIPARTEDIQUALSIASIPRODOTTO

INVIATOAEIZOOISUOIDISTRIBUTORIPERRIPARAZIONI.

EIZOEISUOIDISTRIBUTORINONOFFRONOALCUNAGARANZIAADDIZIONALE,IMPLICITAOESPLICITA,

RIGUARDO IL PRODOTTO E LA SUA QUALITÀ, PRESTAZIONI, VENDIBILITÀ OAPPROPRIATEZZA PER

QUALSIASIUSOPARTICOLARE.INNESSUNCASOEIZOOIDISTRIBUTORIEIZOAUTORIZZATISARANNO

RESPONSABILI PER QUALSIASI DANNOACCIDENTALE, INDIRETTO, SPECIALE, CONSEGUENTE O DI

QUALSIASIALTRANATURA(INCLUSI,SENZALIMITI,DANNIPERPERDITADIPROFITTI,INTERRUZIONEDELLE

ATTIVITÀ,PERDITADIINFORMAZIONID’AFFARIOQUALSIASIALTRAPERDITAPECUNIARIA)DERIVANTI

DALL’USOODALL’IMPOSSIBILITÀDIUSAREILPRODOTTOOINQUALSIASIRELAZIONEALPRODOTTO,

SIASUBASEDICONTRATTO,TORTO,NEGLIGENZA,STRETTARESPONSABILITÀOALTRIMENTI,ANCHE

SEEIZOOIDISTRIBUTORIEIZOAUTORIZZATISONOSTATIAVVERTITIDELLAPOSSIBILITÀDITALIDANNI.

QUESTAESCLUSIONEINCLUDEANCHEQUALSIASIRESPONSABILITÀCHEPOSSAINSORGEREDARECLAMI

DITERZICONTROL’ACQUIRENTEORIGINALE.L’ESSENZADIQUESTOPROVVEDIMENTOÈLIMITARELA

RESPONSABILITÀPOTENZIALEDIEIZOEDEIDISTRIBUTORIDERIVANTEDAQUESTAGARANZIALIMITATAE/O

DALLEVENDITE.

56

Appendix

BEGRÄNSAD GARANTI

EIZO NANAO CORPORATION (nedan kallat “ EIZO”) och EIZOs auktoriserade distributörer (nedan kallade

“ Distributörer”)garanterarienlighetmedvillkorenidennabegränsadegaranti(nedankallad“Garantin”)den ursprungligeköparen(nedankalladden“ Ursprunglige köparen”)somköptedenidokumentetspecificeradeprodukten

(nedankallad“ Produkten”)frånEIZOellerDistributörer,attEIZOellerDistributörerenligtegetgottfinnandekostnadsfritt antingenrepareraellerbytautdendefektaProduktenomdenUrsprungligeköpareninomGarantiperioden(definieras nedan)upptäckerattProduktenfungerarfelaktigtellerskadasundernormalanvändningavProduktenienlighetmed beskrivningenibruksanvisningen(nedankallad“ Bruksanvisning”).

Giltighetsperiodenfördennagarantiärbegränsadtill(i)fem(5)årfråndatumetförProduktensinköpeller,omdetta inträffartidigare,begränsattillutlöpandetav(ii)30000timmarsanvändningavProdukten(härikallad“ Garantiperioden”).

GarantiperiodenförProduktensLCD-panelärdockbegränsadtilltre(3)årfråndatumetförProduktensinköp.EIZOoch

DistributörerskainteundernågravillkorhanågotannatansvaränvadsomangesidennagarantigällandeProdukteni relationtilldenUrsprungligeköparenellertredjepart.

EIZOochDistributörerkommerattupphöramedlagerhållningavProduktensdelareftersju(7)årefterattproduktionen avdessadelarupphört.NätskärmenreparerasanvänderEIZOochdistributörerreservdelarsomuppfyllervåra kvalitetsstandarder.

GarantinärendastgiltigideländerdärdetfinnsDistributörer.GarantinbegränsarintenågraavdenUrsprunglige köparenslagstadgaderättigheter.

OavsettandravillkoridennagarantiskainteEIZODistributörerundernågravillkorhanågotansvarinågotavdefall sombeskrivsnedan:

(a) NärnågonbristfällighethosProduktenkanhärledastillatthauppståttvidfrakt,modifiering,ändring,felaktigt handhavande,olycka,felaktiginstallation,katastrof,felaktigtunderhålloch/ellerfelaktigreparationutfördavtredje partannanänEIZOochDistributörer.

(b) AllaformeravinkompatibilitethosProduktenpågrundavmöjligatekniskainnovationeroch/ellerbestämmelser.

(c) Alla försämringar av bildens prestanda beroende på förbrukningsdelar så som LCD-panel och/eller bakgrundsbelysningetc.(t.ex.ändringariljusstyrka,jämnhetiljusstyrka,färg,färgjämnhet,defektapixlaroch/eller fastlysandepixlaretc.).

(d) AlladefekterhosProduktensomorsakatsavexternutrustning.

(e) AlladefekterhosProduktenpåvilkendetursprungligaserienumretharändratselleravlägsnats.

(f) Allaproduktfelsomorsakasavvätskasomläckerfrånbatteriet.

(g) AllnormalförsämringavProdukten,specielltförbrukningsartiklar,tillbehöroch/elleryttredelar(t.ex.batterier, knappar,roterandedelar,fjärrkontroll,kablar,Bruksanvisningenetc.).

(h) Varjedeformation,missfärgningoch/ellerskevhetavProduktensyttreinklusiveytanpåLCD-panelen.

FöratterhållaserviceunderdennagarantimåstedenUrsprungligeköparen(medhänseendetillriskenförskada och/ellerförlustundertransport)levereraProduktentillnärmasteDistributörmedförebetaldfrakt,idessursprungliga förpackningellerannanfullgodförpackningsomgerlikvärdigtskydd.DenUrsprungligeköparenmåstekunnavisa inköpsbevisförProduktensomklargörProduktensinköpsdatumvidbegäranavgarantiservice.

Garantiperiodenförallautbyttaoch/ellerrepareradeprodukterunderdennagarantiskallupphöravidutgångenavden ursprungligaGarantiperioden.

EIZOELLERDISTRIBUTÖRERÄRINTEANSVARIGAFÖRNÅGONFORMAVSKADAELLERFÖRLUSTAVDATA

ELLERANNANINFORMATIONSOMHARLAGRATSINÅGONFORMAVMEDIAELLERANNANDELAVNÅGON

PRODUKTSOMHARRETURNERATSTILLEIZOELLERDISTRIBUTÖRERFÖRREPARATION.

EIZO OCH DISTRIBUTÖRERNA GARANTERAR INGET, UTTRYCKLIGEN ELLER UNDERFÖRSTÅTT, VAD

BETRÄFFARPRODUKTENOCHDESSKVALITET,PRESTANDA,SÄLJBARHETELLERLÄMPLIGHETFÖRNÅGON

FORMAVSPECIELLANVÄNDNING.UNDERINGAOMSTÄNDIGHETERSKALLEIZOELLERDISTRIBUTÖRERNA

HÅLLASANSVARIGAFÖRNÅGRASOMHELSTUNDERORDNADE,INDIREKTA,SPECIELLA,DÄRAVFÖLJANDE

ELLERÖVRIGASKADOR(INKLUSIVE,UTANBEGRÄNSNINGTILL,SKADORFÖRFÖRLUSTAVINKOMST,

AVBRUTENAFFÄRSRÖRELSE,FÖRLUSTAVAFFÄRSINFORMATIONELLERANNANSÄRSKILDFÖRLUST)SOM

UPPSTÅTTSOMETTRESULTATAVANVÄNDNINGELLEROFÖRMÅGAATTANVÄNDAPRODUKTENELLERI

NÅGONFORMAVANSLUTNINGTILLPRODUKTERNA,VARESIGDETTAGRUNDASPÅKONTRAKT,ÅTALBAR

HANDLING,FÖRSUMLIGHET,ANSVARSSKYLDIGHETELLERANNAT,ÄVENOMEIZOELLERDISTRIBUTÖRERNA

HARINFORMERATSBETRÄFFANDEMÖJLIGHETATTSÅDANASKADORFÖRELIGGER.DETTAUNDANTAG

OMFATTARÄVENALLFORMAVANSVARSSKYLDIGHETSOMKANUPPSTÅGENOMENTREDJEPARTSANSPRÅK

GENTEMOTDENURSPRUNGLIGEKÖPAREN.GRUNDBESTÅNDSDELENIBESTÄMMELSENÄRATTBEGRÄNSA

DETEVENTUELLAANSVARSTAGANDETFÖREIZOOCHDISTRIBUTÖRERNASOMKANUPPSTÅGENOMDENNA

BEGRÄNSADEGARANTIOCH/ELLERFÖRSÄLJNING.

Appendix

57

ΠΕΡΙΟΡΙΣΜΕΝΗ ΕΓΓΥΗΣΗ

ΗEIZONANAOCORPORATION(στοεξής« EIZO»)καιοιδιανομείςπουεξουσιοδοτείηEIZO(στοεξής«Διανομείς»)

παρέχουνεγγύηση,υποκείμενηκαισύμφωναμετουςόρουςτηςπαρούσαςπεριορισμένηςεγγύησης(στοεξής

« Εγγύηση»),στοναρχικόαγοραστή(στοεξής«Αρχικός Αγοραστής»)οοποίοςαγόρασετοπροϊόνπουκαθορίζεταιστο

παρόνέγγραφο(στοεξής« Προϊόν»)απότηνEIZOήτουςΔιανομείς,ηοποίαεξασφαλίζειότιηEIZOκαιοιΔιανομείς,

σύμφωναμετηδιακριτήευχέρειάτους,είτεθαεπισκευάσουνείτεθααντικαταστήσουντοΠροϊόνχωρίςχρέωσηεάνο

ΑρχικόςΑγοραστήςαντιληφθείεντόςτηςΠεριόδουΕγγύησης(ορίζεταικατωτέρω)ότιτοΠροϊόνδυσλειτουργείήέχει

υποστείβλάβηκατάτηδιάρκειακανονικήςχρήσηςτουΠροϊόντοςσύμφωναμετηνπεριγραφήστοεγχειρίδιοχρήσηςπου

συνοδεύειτοΠροϊόν(στοεξής« Εγχειρίδιο Χρήστη»).

ΗπερίοδοςτηςπαρούσαςΕγγύησηςείναι(i)πέντε(5)έτηαπότηνημερομηνίααγοράςτουΠροϊόντος,ή,στηλήξητων

(ii)30.000ωρώνχρήσηςτουΠροϊόντος(στοεξής« Περίοδος Εγγύησης»),μετηνπροϋπόθεση,ωστόσο,ότιηΠερίοδος

ΕγγύησηςγιατηνοθόνηLCDτουΠροϊόντοςπεριορίζεταισετρία(3)έτηαπότηνημερομηνίααγοράςτουΠροϊόντος.Η

EIZOκαιοιΔιανομείςδενφέρουνκαμίαευθύνηήυποχρέωσηόσοναφοράτοΠροϊόνσεσχέσημετονΑρχικόΑγοραστή ήοποιοδήποτετρίτομέρος,ούτεάλληευθύνηδιαφορετικήαπόαυτήνπουπαρέχεταιστηνπαρούσαΕγγύηση.

ΗEIZOκαιοιΔιανομείςθαπαύσουνναδιατηρούνήνααποθηκεύουντυχόνεξαρτήματατουΠροϊόντοςκατόπιντηςλήξης

τωνεπτά(7)ετώνμετάτηδιακοπήτηςπαραγωγήςτέτοιωνεξαρτημάτων.Κατάτηνεπισκευήτηςοθόνης,ηEIZOκαιοι

ΔιανομείςθαχρησιμοποιήσουνανταλλακτικάεπισκευήςπουσυμμορφώνονταιμεταπρότυπάμαςγιατηΔιασφάλιση

Ποιότητας.

ΗΕγγύησηισχύειμόνοσεχώρεςήπεριοχέςόπουβρίσκονταιοιΔιανομείς.ΗΕγγύησηδενπεριορίζειοποιαδήποτε

νόμιμαδικαιώματατουΑρχικούΑγοραστή.

ΛαμβανομένηςυπόψηκάθεδιάταξηςτηςπαρούσαςΕγγύησης,ηEIZOκαιοιΔιανομείςδενθαέχουνκαμίααπολύτως

υποχρέωσησύμφωναμετηνπαρούσαΕγγύησησεοποιαδήποτεαπότιςπεριπτώσειςπουδιατυπώνονταικατωτέρω:

(α) ΤυχόνελάττωματουΠροϊόντοςπουπροκαλείταιαπόζημιάκατάτημεταφορά,τροποποίηση,αλλαγή,κατάχρηση,

λανθασμένηχρήση,ατύχημα,λανθασμένηεγκατάσταση,καταστροφή,εσφαλμένησυντήρησηή/καιλανθασμένη

επισκευήαπότρίτομέροςεκτόςτηςEIZOκαιτωνΔιανομέων,

(β) ΤυχόνασυμβατότητατουΠροϊόντοςλόγωπιθανώντεχνικώνκαινοτομιώνή/καικανονισμών,

(γ) Τυχόνεπιδείνωσητηςαπόδοσηςοθόνηςπουπροκαλείταιαπότηφθοράαναλώσιμωνεξαρτημάτωνόπως

τηςοθόνηςLCDή/καιτουφωτόςυποβάθρου,κτλ.(π.χ.αλλαγέςστηφωτεινότητα,αλλαγέςστηνομοιομορφία

φωτεινότητας,αλλαγέςστοχρώμα,αλλαγέςστηνομοιομορφίαχρώματος,ελαττώματασεpixelπεριλαμβανομένων

τωνκαμένωνpixel,κτλ.),

(δ) ΤυχόνελάττωματουΠροϊόντοςπουπροκαλείταιαπόεξωτερικόεξοπλισμό,

(ε) ΤυχόνελάττωματουΠροϊόντοςστοοποίοέχειτροποποιηθείήαφαιρεθείογνήσιοςαριθμόςσειράς,

(στ)ΤυχόνελάττωματουΠροϊόντοςπουπροκαλείταιαπόδιαρροήυγρούαπότηνμπαταρία,

(ζ) Τυχόν φυσιολογική φθορά του προϊόντος, ιδιαίτερα αυτής των αναλώσιµων, των αξεσουάρ ή/και των

προσαρτηµάτων(π.χ.μπαταρίες,κουµπιά,περιστρεφόµεναµέρη,τηλεχειριστήριο,καλώδια,ΕγχειρίδιοΧρήστη,

κτλ.),και

(η) Τυχόν παραμόρφωση, αποχρωματισμό ή/και διαστρέβλωση του εξωτερικού μέρους του προϊόντος,

περιλαμβανομένηςτηςεπιφάνειαςτηςοθόνηςLCD.

ΟΑρχικόςΑγοραστήςγιαναδικαιούταιυπηρεσίεςεπισκευήςσύμφωναμετηνΕγγύηση,θαπρέπειναπαραδώσειτο

Προϊόν,μεπληρωμέναταμεταφορικάέξοδα,στηναρχικήτουσυσκευασίαήσεάλληεπαρκήσυσκευασίαμεισότιμο

βαθμόπροστασίας,αναλαμβάνονταςτονκίνδυνοβλάβηςή/καιαπώλειαςκατάτημεταφορά,στοντοπικόΔιανομέα.Ο

ΑρχικόςΑγοραστήςότανζητάυπηρεσίεςεπισκευήςσύμφωναμετηνΕγγύηση,θαπρέπειναπροσκομίζειτηναπόδειξη

αγοράςτουΠροϊόντοςκαιτηνημερομηνίατηςαγοράς.

ΗΠερίοδοςΕγγύησηςγιαοποιοδήποτεαντικατεστημένοή/καιεπισκευασμένοπροϊόνσύμφωναμετηνπαρούσα

ΕγγύησηλήγειστοτέλοςτηςαρχικήςΠεριόδουΕγγύησης.

ΗEIZOΉΟΙΔΙΑΝΟΜΕΙΣΔΕΝΕΥΘΥΝΟΝΤΑΙΓΙΑΟΠΟΙΑΔΗΠΟΤΕΒΛΑΒΗΉΑΠΩΛΕΙΑΔΕΔΟΜΕΝΩΝΉΑΛΛΩΝ

ΠΛΗΡΟΦΟΡΙΩΝ ΠΟΥΑΠΟΘΗΚΕΥΟΝΤΑΙ ΣΕ ΟΠΟΙΟΔΗΠΟΤΕ ΜΕΣΟ Ή ΟΠΟΙΟΔΗΠΟΤΕΑΛΛΟ ΜΕΡΟΣ ΣΕ

ΟΠΟΙΟΔΗΠΟΤΕΠΡΟΪΟΝΠΟΥΕΠΙΣΤΡΕΦΕΤΑΙΣΤΗΝEIZOΉΣΕΔΙΑΝΟΜΕΑΓΙΑΕΠΙΣΚΕΥΗ.

ΗEIZOΚΑΙΟΙΔΙΑΝΟΜΕΙΣΔΕΝΠΑΡΕΧΟΥΝΚΑΜΙΑΠΕΡΑΙΤΕΡΩΕΓΓΥΗΣΗ,ΡΗΤΗΉΣΥΝΕΠΑΓΟΜΕΝΗ,ΟΣΟΝ

ΑΦΟΡΑΤΟΠΡΟΪΟΝΚΑΙΤΗΝΠΟΙΟΤΗΤΑ,ΤΗΝΑΠΟΔΟΣΗ,ΤΗΝΕΜΠΟΡΕΥΣΙΜΟΤΗΤΑΉΤΗΝΚΑΤΑΛΛΗΛΟΤΗΤΑ

ΤΟΥ ΓΙΑ ΟΠΟΙΑΔΗΠΟΤΕ ΣΥΓΚΕΚΡΙΜΕΝΗ ΧΡΗΣΗ. ΣΕ ΚΑΜΙΑ ΠΕΡΙΠΤΩΣΗ Η EIZO Ή ΟΙΔΙΑΝΟΜΕΙΣΔΕΝ

ΘΑ ΕΥΘΥΝΟΝΤΑΙ ΓΙΑ ΚΑΜΙΑΑΠΟΛΥΤΩΣΤΥΧΑΙΑ, ΕΜΜΕΣΗ, ΕΙΔΙΚΗ, ΣΥΝΕΠΑΓΟΜΕΝΗ ΉΑΛΛΗ ΒΛΑΒΗ

(ΠΕΡΙΛΑΜΒΑΝΟΜΕΝΩΝ,ΜΕΤΑΞΥΑΛΛΩΝ,ΒΛΑΒΩΝΉΑΠΩΛΕΙΑΣΚΕΡΔΩΝ,ΔΙΑΚΟΠΗΣΕΠΙΧΕΙΡΗΜΑΤΙΚΩΝ

ΔΡΑΣΤΗΡΙΟΤΗΤΩΝ,ΑΠΩΛΕΙΑΣΕΠΙΧΕΙΡΗΜΑΤΙΚΩΝΠΛΗΡΟΦΟΡΙΩΝΉΤΥΧΟΝΑΛΛΗΣΧΡΗΜΑΤΙΚΗΣΑΠΩΛΕΙΑΣ)

ΠΟΥΠΡΟΚΥΠΤΕΙΑΠΟΤΗΧΡΗΣΗΉΤΗΝΑΝΙΚΑΝΟΤΗΤΑΧΡΗΣΗΣΤΟΥΠΡΟΪΟΝΤΟΣΉΤΥΧΟΝΑΛΛΗΣΣΥΝΔΕΣΗΣ

ΜΕΤΟΠΡΟΪΟΝ,ΕΙΤΕΒΑΣΙΖΕΤΑΙΣΕΣΥΜΒΟΛΑΙΟ,ΒΛΑΒΗ,ΑΜΕΛΕΙΑ,ΑΥΣΤΗΡΗΕΥΘΥΝΗΉΕΙΔΑΛΛΩΣ,ΑΚΟΜΗ

ΚΙΕΑΝΗEIZOΉΟΙΔΙΑΝΟΜΕΙΣΕΝΗΜΕΡΩΘΟΥΝΓΙΑΤΗΝΠΙΘΑΝΟΤΗΤΑΤΕΤΟΙΩΝΖΗΜΙΩΝ.ΗΕΞΑΙΡΕΣΗΑΥΤΗ

ΠΕΡΙΛΑΜΒΑΝΕΙΕΠΙΣΗΣΟΠΟΙΑΔΗΠΟΤΕΕΥΘΥΝΗΕΝΔΕΧΕΤΑΙΝΑΠΡΟΚΥΨΕΙΑΠΟΑΞΙΩΣΕΙΣΤΡΙΤΟΥΜΕΡΟΥΣ

ΚΑΤΑΤΟΥΑΡΧΙΚΟΥΑΓΟΡΑΣΤΗ.ΗΟΥΣΙΑΤΟΥΟΡΟΥΑΥΤΟΥΕΙΝΑΙΝΑΠΕΡΙΟΡΙΣΕΙΤΗΝΠΙΘΑΝΗΕΥΘΥΝΗΤΗΣ

EIZOΚΑΙΤΩΝΔΙΑΝΟΜΕΩΝΠΟΥΠΡΟΚΥΠΤΕΙΑΠΟΤΗΝΠΑΡΟΥΣΑΕΓΓΥΗΣΗΉ/ΚΑΙΤΙΣΠΩΛΗΣΕΙΣ.

58

Appendix

ОГРАНИЧЕННАЯ ГАРАНТИЯ

EIZONANAOCORPORATION(называемаявдальнейшем“ EIZO”)иавторизированныеEIZOдистрибуторы

(называемыевдальнейшем“ Дистрибуторы”)гарантируют,всоответствиисусловиямиипунктамиэтой ограниченнойгарантии(называемойвдальнейшем“ Гарантия”),первичномупокупателю(называемомув дальнейшем“ Первоначальный покупатель”),которыйприобрелуEIZOилиДистрибуторовпродукт,указанный вэтомдокументе(называемыйвдальнейшем“ Продукт”),чтоEIZOилиДистрибуторынасвоеусмотрение либобесплатноотремонтируют,либобесплатнозаменятПродукт,еслиПервоначальныйпокупательпризнает впределахГарантийногосрока(определенногониже),чтоПродуктнеисправенилионповрежденпроцессе нормальногоиспользованияпродуктавсоответствиисописаниемвинструкциипоэксплуатации,прилагаемойк

Продукту(называемойвдальнейшем“ Руководство пользователя”).

Гарантийныйпериодограниченсроком(i)пять(5)летотдатыприобретенияПродукта,илиограниченсроком(ii)

30000часовиспользованияПродукта(называемыйвдальнейшем“ Гарантийный период”),приусловии,что

ГарантийныйпериоддляпанелиЖКДограниченсрокомтри(3)годаотдатыприобретенияПродукта.EIZOи

ДистрибуторыненесутникакойответственностиинеберутобязательствотносительноПродуктапоотношениюк

Первоначальномупокупателюилипоотношениюклюбымтретьимсторонам,кромеобязательств,оговоренныхв этойГарантии.

EIZOиДистрибуторыпрекратятхранениеилискладированиелюбыхдеталейПродуктапоистечениисеми(7) летпослепрекращенияпроизводстватакихдеталей.ВслучаеремонтамонитораEIZOиДистрибьюторыбудут использоватьзапчасти,которыесоответствуютнашимстандартамQC(контролькачества).

Гарантия действительна только в странах или регионах, где расположены Дистрибуторы. Гарантия не ограничиваетникакиезаконныеправаПервоначальногопокупателя.

НесмотрянадругиеусловияэтойГарантииEIZOиДистрибуторыненесутникакихобязательствсогласноэтой

Гарантиивлюбомизперечисленныхнижеслучаев:

(а) ЛюбыедефектыПродукта,вызванныеповреждениямиприперевозке,модификацией,изменением, неправильным обращением, неправильным использованием, авариями, неправильной установкой, стихийнымибедствиями,неправильнымуходоми/илинеправильнымремонтомтретьейстороной,отличной отEIZOилиДистрибуторов;

(б) ЛюбыенесовместимостиПродуктаиз-затехническихусовершенствованийи/илиизменениятехнических норм;

(в) Любые ухудшения работы дисплея, вызванные изнашиванием невосстановимых частей, таких как панельЖКДи/илиподсветкаит.д.(например,изменениевяркости,изменениевравномерностияркости, изменениевцветности,изменениевравномерностицветности,изменениевпикселах,включаявыгоревшие пикселыит.д.);

(г) ЛюбыедефектыПродукта,вызванныевнешнимоборудованием;

(д) ЛюбыедефектыПродукта,прикоторыхоригинальныйсерийныйномербылизмененилиудален;

(е) ЛюбыедефектыПродукта,вызванныепротеканиембатарейки;

(ж) Любые естественные ухудшения продукта, в частности, вызванные износом расходных частей, принадлежностейи/илиприспособлений(например,батареек,кнопок,вращающихсячастей,пульта дистанционногоуправления,кабелей,Руководствапользователяит.д.);и

(з) Любые деформации, изменения цвета и/или коробления внешней поверхности продукта, включая поверхностьпанелиЖКД.

ЧтобыполучитьтехническоеобслуживаниеврамкахГарантии,Первоначальныйпокупательдолжендоставить

ПродуктместномуДистрибутору,оплативперевозку,вегооригинальнойупаковкеиливдругойсоответствующей упаковке,обеспечивающейравноценнуюстепеньзащиты,принимаявовниманиерискповрежденияи/илиутерю притранспортировке.ПризапросетехническогообслуживанияврамкахГарантииПервоначальныйпокупатель долженпредоставитьсвидетельствопокупкипродуктаидатыпокупки.

Гарантийныйпериоддлялюбогозамененногои/илиотремонтированногопродуктаврамкахГарантииистекаетв концезавершениясрокадействияоригинальногоГарантийногопериода.

EIZO ИЛИ ДИСТРИБУТОРЫ НЕ НЕСУТ ОТВЕТСТВЕННОСТИ ЗА ЛЮБЫЕ ПОВРЕЖДЕНИЯ ИЛИ УТЕРЮ

ДАННЫХИЛИДРУГОЙИНФОРМАЦИИ,ХРАНЯЩИХСЯНАКАКИХ-ЛИБОНОСИТЕЛЯХИНФОРМАЦИИИЛИНА

ЛЮБЫХДРУГИХЧАСТЯХПРОДУКТА,КОТОРЫЙВОЗВРАЩЕНEIZOИЛИДИСТРИБУТОРАМДЛЯРЕМОНТА.

EIZO И ДИСТРИБУТОРЫ НЕ ДАЮТ НИКАКОЙ ДА ЛЬНЕЙШЕЙ ГАРАНТИИ, ВЫРАЖЕННОЙ ИЛИ

ПОДРАЗУМЕВАЕМОЙ,ОТНОСИТЕЛЬНОПРОДУКТАИЕГОКАЧЕСТВА,ТЕХНИЧЕСКИХХАРАКТЕРИСТИК,

ТОВАРНОСТИИЛИСООТВЕТСТВИЯДЛЯКАКОГО-ЛИБООПРЕДЕЛЕННОГОИСПОЛЬЗОВАНИЯ.НИПРИ

КАКИХУСЛОВИЯХEIZOИЛИДИСТРИБУТОРЫНЕНЕСУТОТВЕТСТВЕННОСТИЗАЛЮБОЙСЛУЧАЙНЫЙ,

КОСВЕННЫЙ,СПЕЦИАЛЬНЫЙ,ПОБОЧНЫЙИЛИИНОЙУЩЕРБ(ВКЛЮЧАЯ,БЕЗОГРАНИЧЕНИЙ,УЩЕРБИЗ-

ЗАНЕПОЛУЧЕННОЙПРИБЫЛИ,ПРЕРЫВАНИЯБИЗНЕСА,ПОТЕРИКОММЕРЧЕСКОЙИНФОРМАЦИИИЛИ

ЛЮБЫЕДРУГИЕФИНАНСОВЫЕПОТЕРИ),ВОЗНИКШИЙИЗ-ЗАИСПОЛЬЗОВАНИЯИЛИНЕВОЗМОЖНОСТИ

ИСПОЛЬЗОВАТЬ ПРОДУКТ ИЛИ В ЛЮБОЙ ДРУГОЙ СВЯЗИ С ПРОДУКТОМ, ЛИБО ОСНОВАННЫЙ НА

КОНТРАКТНЫХ ОТНОШЕНИЯХ, ГРАЖДАНСКИХ ПРАВОНАРУШЕНИЯХ, НЕБРЕЖНОСТИ, ПРИЧИНЕНИЯ

УЩЕРБА ТРЕТЬЕЙ СТОРОНЕ ИЛИ ЧЕМ-ЛИБО ЕЩЕ, ДАЖЕ ЕСЛИ EIZO ИЛИ ДИСТРИБУТОРЫ БЫЛИ

УВЕДОМЛЕНЫ О ВОЗМОЖНОСТИ ТАКОГО УЩЕРБА. ЭТО ИСКЛЮЧЕНИЕ ТАКЖЕ ВКЛЮЧАЕТ ЛЮБЫЕ

ОБЯЗАТЕЛЬСТВА, КОТОРЫЕ МОГУТ ВОЗНИКНУТЬ В РЕЗУЛЬТАТЕ ТРЕБОВАНИЙ ТРЕТЬЕЙ СТОРОНЫ

В ОТНОШЕНИИ ПЕРВОНАЧАЛЬНОГО ПОКУПАТЕЛЯ. СУЩЕСТВОМ ЭТОГО ПОЛОЖЕНИЯ ЯВЛЯЕТСЯ

ОГРАНИЧЕНИЕПОТЕНЦИАЛЬНОЙОТВЕТСТВЕННОСТИEIZOИДИСТРИБУТОРОВ,ВОЗНИКАЮЩЕЙИЗ-ЗА

ЭТОЙОГРАНИЧЕННОЙГАРАНТИИИ/ИЛИПРОДАЖ.

Appendix

59

有限责任保证书

EIZO NANAO 有限公司

（以下简称 EIZO ）和 EIZO 授权的经销商（以下简称经销商），接受并依照本有限责任保证书

（以下简称保证书）之条款，向从 EIZO 和经销商购买本文中所规定产品（以下简称产品）的原买方（以下称原买方）

提供保证

：在保证期内（规定如下），如果原买方发现按本产品所附使用说明书（以下简称用户手册）所述方式正常使

用本产品过程中

，本产品出现故障或损坏，EIZO 和经销商根据其独自的判断免费修理或更换该产品。

本保证期限定为

(i) 自本产品购买之日起的五 (5) 年期间或限定为到达

但本产品的液晶显示屏

（LCD）的保证期限定为自本产品购买之日起的三 (3) 年期间。EIZO 和经销商将不向原买方或任何

第三方承担本保证书所规定之外的与本产品有关任何责任或义务

。

本产品的任何部件停产七

(7) 年后

，EIZO 和经销商将不再保留或保管任何这类部件。维修显示器时，EIZO 与经销商将使

用符合我方质量控制标准的替换零件

。

本保证书仅对于设有经销商的国家或地区有效

。本保证书并不限定原买方的任何法律权利。

无论本保证书的任何其他条款如何规定

，对于任何下列情况之一，EIZO 和经销商将不承担本保证书规定责任：

(a) 由于运输损害

、改装、改动、滥用、误用、意外事故、错误安装、灾害、维护不善和 / 或由除 EIZO 和经销商以外的

第三方进行不适当的修理造成本产品的任何故障

。

(b) 由于可能发生的技术变更和 / 或调整造成本产品的任何不兼容性

。

(c) 由于诸如液晶显示屏

（LCD）和 / 或背灯等消耗品部件的老化造成的任何显示性能低劣（如亮度变化、亮度均一性变化、

色彩变化

、色彩均一性变化、如烧伤像素等像素缺陷）。

(d) 因外部设备造成本产品的任何故障

。

(e) 因本产品的原序号被改变或消除造成本产品的任何故障

。

(f) 因电池液体泄漏造成本产品的任何故障

。

(g) 本产品的任何正常老化

，尤其是消耗品、附件和 / 或附加装置（如电池、按钮、旋转部件、遥控器、电缆、用户手册等）、

以及

(h) 本产品表面包括液晶显示屏

（LCD）表面的任何变形、变色和 / 翘曲。

为了获得本保证书规定的服务

，原买方必须使用原包装或其他具有同等保护程度的适当包装将本产品运送到当地的经销商，

并且预付运费

，承担运输中的损坏和 / 或损失的风险。要求提供本保证书规定的服务时，原买方必须提交购买本产品和标

明此购买日期的证明

。

按本保证书规定进行了更换和

/ 或修理的任何产品的保证期限

，将在原保证期限结束时终止。

在返回给

EIZO 和经销商进行修理后

，任何产品的任何媒体或任何部件中储存的数据或其他信息发生任何损坏或损失，对

此

EIZO 和经销商将不承担责任

。

对于本产品及其质量

、性能、可销售性以及对于特殊用途的适合性，EIZO 和经销商不提供其他任何明示或暗示的保证。因

使用本产品或无法使用本产品或因与本产品有任何关系

（无论是否根据合同）而造成 : 任何附带的、间接的、特殊的、随

之发生的或其他的损害

（包括但不仅限于：利润损失、业务中断、业务信息丢失或其他任何金钱损失）以及侵权行为、过失、

严格赔偿责任或其他责任

，即使已经向 EIZO 和经销商提出了发生这些损害的可能性，对此 EIZO 和经销商概不承担责任。

本免责条款还包括因第三方向原买方提出索赔而可能发生的任何责任

。本条款的本质是限定由于本有限责任保证书和 / 或

销售本产品所发生的

EIZO 和经销商的潜在责任

。

60

Appendix

China Measures for RoHS Compliance in ChinaRoHS

关于电子信息产品污染控制标识

数字为环保使用期限的年数。只要您遵守该产品相关的安全及使用注意事项，在自制造日起算的年限内，不会

产生对环境污染或人体及财产的影响。上述标识粘贴在机器背面。

• 有毒有害物质或元素的名称及含量

部件名称

印刷电路板

机箱

液晶显示器

其他

铅

（Pb）

×

○

×

×

汞

（Hg）

○

○

×

○

有毒有害物质或元素

镉

（Cd）

○

○

○

○

六价铬

○

○

○

○

多溴联苯

（PBB）

○

○

○

○

多溴二苯醚

（PBDE）

○

○

○

○

○ ：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 规定的限量要求以下。

× ：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 规定的限量要求。

( 企业可在此处 , 根据实际情況对上表中打“×

” 的技术原因进行进一步说明 )

Appendix

61

No results