Toro Flex-Force Power System 60V Stick Edger Operator's Manual
Toro Flex-Force is a powerful and versatile edger designed to help you maintain a neat and tidy lawn. With its 60V lithium-ion battery, it delivers ample power to tackle tough edging jobs, while its adjustable cutting depth and angle allow you to customize your edging to your preference. The lightweight design and ergonomic handle ensure comfortable operation, making it easy to maneuver the edger around your yard.
Werbung
Werbung
Form No. 3461-112 Rev A
Flex-Force Power System
™
60V
Stick Edger
Model No. 51833—Serial No. 323000001 and Up
Model No. 51833T—Serial No. 323000001 and Up
Register at www.Toro.com.
Original Instructions (EN)
*3461-112*
For assistance, please see www.Toro.com/support for instructional videos or contact 1-888-384-9939 before returning this product.
WARNING
CALIFORNIA
Proposition 65 Warning
The power cord on this product contains lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling.
Use of this product may cause exposure to chemicals known to the State of
California to cause cancer, birth defects, or other reproductive harm.
Whenever you need service, genuine the manufacturer parts, or additional information, contact an Authorized Service Dealer or the manufacturer
Customer Service and have the model and serial numbers of your product ready.
identifies the location of the model and serial numbers on the product. Write the numbers in the space provided.
Important: With your mobile device, you can scan the QR code on the serial number decal (if equipped) to access warranty, parts, and other product information.
g428616
Introduction
This edger is intended to be used by residential homeowners to trim grass around the edge of driveways, sidewalks, and more as needed outdoors.
It is designed to use Toro 60V lithium-ion battery packs. These battery packs are designed to be charged only by Toro 60V lithium-ion battery chargers.
Using this product for purposes other than its intended use could prove dangerous to you and bystanders.
Model 51833T does not include a battery or a charger.
Read this information carefully to learn how to operate and maintain your product properly and to avoid injury and product damage. You are responsible for operating the product properly and safely.
Visit www.Toro.com for product safety and operation training materials, accessory information, help finding a dealer, or to register your product.
Figure 1
1.
Model and serial number location
Model No.
Serial No.
© 2023—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
2
Contact us at www.Toro.com.
Printed in China
All Rights Reserved
Safety-Alert Symbol
The safety-alert symbol ( Figure 2
) shown in this manual and on the machine identifies important safety messages that you must follow to prevent accidents.
Figure 2
Safety-alert symbol g000502
The safety-alert symbol appears above information that alerts you to unsafe actions or situations and is followed by the word DANGER , WARNING , or
CAUTION .
DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
This manual uses two other words to highlight information.
Important calls attention to special mechanical information and Note emphasizes general information worthy of special attention.
Safety
IMPORTANT SAFETY
INSTRUCTIONS
WARNING
When using electric gardening tools, always read and follow basic safety warnings and instructions to reduce the risk of fire, electric shock, and personal injury, including the following:
Read All Instructions
I. Training
1.
The operator of the tool is responsible for any accidents or hazards occurring to others or their property.
2.
Do not allow children to use or play with the tool, battery pack, or the battery charger; local regulations may restrict the age of the operator.
3.
Do not allow children or untrained people to operate or service this device. Allow only people who are responsible, trained, familiar with the instructions, and physically capable to operate or service the device.
4.
Before using the tool, battery pack, and battery charger, read all the instructions and cautionary markings on these products.
5.
Become familiar with the controls and proper use of the tool, battery pack, and battery charger.
II. Preparation
1.
Keep bystanders and children away from the operating area.
2.
Use only the battery pack specified by Toro.
Using other accessories and attachments may increase the risk of injury and fire.
3.
Plugging the battery charger into an outlet that is not 120 V can cause a fire or electric shock. Do not plug the battery charger into an outlet other than 120 V. For a different style of connection, use an attachment plug adapter of the proper configuration for the power outlet if needed.
4.
Do not use a damaged or modified battery pack or battery charger, which may exhibit unpredictable behavior that results in fire, explosion, or risk of injury.
5.
If the supply cord to the battery charger is damaged, contact an Authorized Service Dealer to replace it.
6.
Charge the battery pack with only the battery charger specified by Toro. A charger suitable for
3
1 type of battery pack may create a risk of fire when used with another battery pack.
7.
Charge the battery pack in a well-ventilated area only.
8.
Follow all charging instructions and do not charge the battery pack outside of the temperature range specified in the instructions.
Otherwise, you may damage the battery pack and increase the risk of fire.
9.
Do not operate the tool without all guards and other safety protective devices in place and functioning properly on the tool.
10.
Dress properly—Wear appropriate clothing, including eye protection; long pants; substantial, slip-resistant footwear; rubber gloves; and hearing protection. Tie back long hair and do not wear loose clothing or loose jewelry that can get caught in moving parts. Wear a dust mask in dusty operating conditions.
III. Operation
1.
Avoid dangerous environments—Do not use the tool in rain or in damp or wet locations.
2.
Use the proper tool for your application—Using the tool for purposes other an its intended use could prove dangerous to you and bystanders.
3.
Prevent unintentional starting—Ensure that the switch is in the O FF position before connecting to the battery pack and handling the tool. Do not carry the tool with your finger on the switch or energize the tool with the switch in the O N position.
4.
Operate the tool only in daylight or good artificial light.
5.
If the tool strikes an object or starts to vibrate, immediately shut off the tool, wait for all moving parts to stop, and disconnect the battery before examining the tool for damage. Make all necessary repairs before resuming operation
6.
Remove the battery pack from the tool before adjusting it or changing accessories.
7.
Keep your hands and feet away from the cutting area and all moving parts.
8.
Shut off the tool, remove the battery pack from the tool, and wait for all movement to stop before adjusting, servicing, cleaning, or storing the tool.
9.
Remove the battery pack from the tool whenever you leave it unattended.
10.
Do not force the tool—Allow the tool to do the job better and safer at the rate for which it was designed.
11.
Do not overreach—Keep proper footing and balance at all times, especially on slopes. Walk, never run with the tool.
12.
Stay alert—Watch what you are doing and use common sense when operating the tool. Do not use the tool while ill, tired, or under the influence of alcohol or drugs.
13.
Ensure that the ventilation openings are kept clear of debris.
14.
Under abusive conditions, the battery pack may eject liquid; avoid contact. If you accidently come into contact with the liquid, flush with water. If the liquid contacts your eyes, seek medical help. Liquid ejected from the battery pack may cause irritation or burns.
15.
Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 130°C (265°F) may cause explosion.
16.
CAUTION—A mistreated battery pack may present a risk of fire, explosion, or chemical burn.
• Do not disassemble the battery pack.
• Replace the battery pack with a genuine
Toro battery pack only; using another type of battery pack may cause a fire or risk of injury.
• Keep battery packs out of the reach of children and in the original packaging until you are ready to use them.
IV. Maintenance and Storage
1.
Maintain the tool with care—Keep it clean and in good repair for best performance and to reduce the risk of injury. Follow the instructions for lubricating and changing accessories. Keep handles dry, clean, and free from oil and grease.
2.
When the battery pack is not in use, keep it away from metal objects such as paper clips, coins, keys, nails, and screws that can make a connection from 1 terminal to another. Shorting the battery terminals may cause burns or a fire.
3.
Keep your hands and feet away from moving parts.
4.
Shut off the tool, remove the battery pack from the tool, and wait for all movement to stop before adjusting, servicing, cleaning, or storing the tool.
5.
Check the tool for damaged parts—If there are damaged guards or other parts, determine whether it will operate properly. Check for misaligned and binding moving parts, broken parts, mounting, and any other condition that may affect its operation. Unless indicated in the instructions, have an Authorized Service Dealer repair or replace a damaged guard or part.
6.
If the blade becomes worn, bent, or damaged, replace it; contact an authorized Toro distributor.
4
7.
Do not attempt to service or repair the tool, battery pack, or battery charger except as indicated in the instructions. Have an Authorized
Service Dealer perform service using identical replacement parts to ensure that the product is safely maintained.
8.
Store an idle tool indoors in a place that is dry, secure, and out of the reach of children.
9.
Do not dispose of the battery in a fire. The cell may explode. Check with local codes for possible special disposal instructions.
SAVE THESE
INSTRUCTIONS
5
Safety and Instructional Decals
Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing.
144-3098 decal144-3098 decal144-3096
144-3096 decal144-3094
1.
The battery pack is charging.
144-3094
2.
The battery pack is fully charged.
3.
The battery pack is over or under the appropriate temperature range.
4.
Battery pack charging fault decal140-8475
1.
Read the Operator’s
Manual .
2.
Call2Recycle® battery recycling program
140-8475
3.
Keep away from open fire or flames.
4.
Do not expose to rain.
6
1.
Battery charge status
137-9461 decal137-9461 decal139-5210
139-5210
1.
Warning—read the Operator’s Manual ; stay away from moving parts; keep all guards in place; wear eye protection; do not operate in wet conditions.
decal139-5346
139-5346
7
Setup
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
Description
Allen wrench
Auxiliary handle assembly
Edger adjustment tool
Qty.
1
1
1
Unfold the handle.
Use
Install the auxiliary handle.
Important: The battery pack is not fully charged when you purchase it. Before using the tool for the first time, refer to
Charging the Battery Pack (page 14)
.
1
Unfolding the Handle
Parts needed for this procedure:
1 Allen wrench
Procedure
1.
Unfold the handle (A of
2.
Align the locking button on the lower shaft with the slotted hole on the upper shaft and slide the 2 shafts together (B and C of
Note:
The locking button clicks into the slotted hole when the shafts are secured (D of
3.
Using the provided Allen wrench, tighten the screw on the shaft connector until it is secure (E of
8
Figure 3
9 g333338
2
Installing the Auxiliary Handle
Parts needed for this procedure:
1
1
Auxiliary handle assembly
Edger adjustment tool
Procedure
1.
Separate the auxiliary handle from the handle plate by removing the 4 screws (A of
).
2.
Line up the auxiliary handle with auxiliary handle plate on the edger handle (B of
3.
Secure the auxiliary handle to the handle plate with the 4 screws previously removed (C of
using the provided Allen wrench.
g333337
Figure 4
10
Product Overview
g429628
Specifications
Model
Blade Length
Rated Voltage
No-load Speed
Weight (without battery pack)
Charger Type
51833
203 mm (8 inches)
60V DC maximum, 54 VDC nominal usage
7000 rpm
4.7 kg (10.4 lbs)
Battery Type
Toro 60V lithium-ion battery chargers
Toro 60V lithium-ion battery packs
Appropriate Temperature Ranges
5°C (41°F) to 40°C (104°F)* Charge/store the battery pack at
Use the battery pack at
Use the machine at
-30°C (-22°F) to 49°C (120°F)*
0°C (32°F) to 49°C (120°F)*
*Charging time will increase if you do not charge the battery within this range.
Store the tool, battery pack, and battery charger in an enclosed clean, dry area.
1.
Battery latch
2.
Lockout button
3.
Auxiliary handle
4.
Run trigger
Figure 5
5.
Guard
6.
Air venting areas
7.
Blade g330065
1.
Battery charger Model
88610 (included with
Model 51833)
Figure 6
2.
Battery pack Model 88620
(included with Model
51833)
Attachments/Accessories
A selection of Toro approved attachments and accessories is available for use with the machine to enhance and expand its capabilities. Contact your Authorized Service Dealer or authorized Toro distributor or go to www.Toro.com for a list of all approved attachments and accessories.
To ensure optimum performance and continued safety certification of the machine, use only genuine Toro replacement parts and accessories. Replacement parts and accessories made by other manufacturers could be dangerous.
11
Operation
Starting the Edger
1.
Align the cavity in the battery pack with the tongue on the handle housing (
).
2.
Push the battery pack into the handle until the battery locks into the latch (
).
Shutting Off the Edger
To shut off the trimmer, release the trigger.
Whenever you are not using the edger or are transporting the edger to or from the work area, remove the battery pack.
Removing the Battery Pack from the Trimmer
Press the battery latch on the machine to release the battery pack and slide the battery pack out of the
).
g333238
Figure 7
1.
Battery latch
3.
To start the edger, pull back on the lockout
button, then squeeze the run trigger ( Figure 8
).
Note:
Once the edger is running you can release the lockout button.
1.
Battery latch
Figure 9 g333240
1.
Lockout button
Figure 8
2.
Run trigger g333239
12
Adjusting the Depth of Cut
1.
Remove the battery from the edger.
2.
Loosen the wing nut on the wheel and move it up or down in the track to increase or decrease
).
g333293
Figure 10
3.
Adjust the depth so that the blade barely touches the ground when the machine is held in a normal working position.
4.
Tighten the wing nut.
5.
Standing in a normal working position, check the depth of cut again and correct if necessary.
13
Charging the Battery Pack
Important: The battery pack is not fully charged when you purchase it. Before using the tool for the first time, place the battery pack in the charger and charge it until the LED display indicates the battery pack is fully charged. Read all safety precautions.
Important: Charge the battery pack only in temperatures that are within the appropriate range; refer to
.
Note:
At any time, press the battery-charge-indicator button on the battery pack to display the current charge (LED indicators).
1.
Ensure that the vents on the battery and charger are clear of any dust and debris.
5.
Refer to the following table to interpret the LED indicator light on the battery charger.
Indicator light
Off
Green blinking
Green
Red
Red blinking
Indicates
No battery pack inserted
Battery pack is charging
Battery pack is charged
Battery pack and/or battery charger is over or under the appropriate temperature range
Battery pack charging fault*
*Refer to
for more information.
Important: The battery can be left on the charger for short periods between uses.
If the battery will not be used for longer periods, remove the battery from the charger; refer to
.
g330066
Figure 11
1.
Battery pack cavity 5.
LED indicators (current charge)
2.
Battery pack venting areas 6.
Handle
3.
Battery pack terminals 7.
Charger
4.
Battery-charge-indicator button
2.
Line up the charger with the cavity on the back
of the battery pack ( Figure 11 ).
3.
Slide the charger into the battery pack until it is fully seated (
).
4.
To remove the charger, slide the charger backward out of the battery.
14
Operating Tips
• Hold the edger with your right hand on the rear handle and your left hand on the front handle.
• Keep a firm grip with both hands while in operation.
• The edger should be held at a comfortable position with the rear handle at about hip height.
• The edger will edge along sidewalks, driveways, flower beds, curbs, and similar areas.
• Cut at a steady pace. If the blade begins to slow down, you are edging too fast; slow your pace. Do not force the blade into the ground.
• Light contact of the blade against the sidewalk edge, curb, etc., is acceptable and will not damage the edger.
• To achieve the best appearance, edge when grass is dry. Edging in wet soil or wet grass areas might clog the blade guard and result in an uneven edge. If the blade guard becomes clogged, stop the edger, remove the battery and remove debris from the blade guard.
1.
Blade
Figure 12
2.
Wheel g333294
15
Maintenance
After each use of the edger, complete the following:
1.
Remove the battery from the edger.
2.
Wipe the edger clean with a damp cloth. Do not hose the edger down or submerge it in water.
3.
Wipe or scrape clean the cutting head area any time there is an accumulation of debris.
4.
Check and tighten all fasteners. If any part is damaged or lost, repair or replace it.
5.
Brush debris away from air intake vents and exhaust on motor housing to prevent the motor from overheating (
).
g334037
1.
Edger adjustment tool
2.
Blade nut
3.
Blade washer
Figure 14
4.
Blade
5.
Blade-secure slot
6.
Screwdriver (not included)
Replacing the Blade
If the blade becomes worn, bent, or damaged, replace it; contact your authorized Toro distributor.
1.
Ensure that the battery is removed from the machine.
2.
Secure the blade so that it cannot spin by inserting a screwdriver (not included) to the slot in the edger head as shown in
.
Note:
You may need to turn the blade to find the slot
3.
Remove the blade nut by turning it clockwise using the edger adjustment tool provided (
6.
Tighten the blade nut by turning it counterclockwise with the wrench provided
(
).
Replacing the Wheel
1.
Ensure that the battery is removed from the machine.
2.
Remove the wing nut, washer, bushings, wheel, rubber washer, and wheel axle from the depth-of-cut track on the edger (
).
g334038
Figure 13
1.
Rotate clockwise to loosen the blade nut
2.
Rotate counterclockwise to tighten the blade nut
4.
Remove the blade washer and the old blade
(
).
Note:
You may discard the old blade.
5.
Install the new blade and secure it with the previously removed blade washer and blade nut.
g334039
1.
Depth-of-cut track
2.
Wheel axle
3.
Wheel
4.
Rubber washer
Figure 15
5.
Bushings
6.
Washer
7.
Wing nut
3.
Replace any damaged or missing parts; contact your authorized Toro distributor.
4.
Insert the wheel axle through the track with the tab facing down as shown in
.
5.
Install the rubber washer, bushings, wheel, small washer, and wing nut to the axle (
).
16
6.
Tighten the wing nut to secure the wheel.
Replacing the Skid Plate
If the skid plate becomes worn or damaged, replace it; contact your authorized Toro distributor.
1.
Ensure that the battery is removed from the machine.
2.
Remove the 2 screws securing the skid plate to
).
1.
Skid plate
Figure 16
2.
Screws g344651
Storage
Important: Store the tool, battery pack, and charger only in temperatures that are within the appropriate range; refer to
.
Important: If you are storing the battery pack for the off-season, remove the battery pack from the tool and charge the battery pack until 2 or 3 LED indicators turn green on the battery. Do not store a fully charged or fully depleted battery. When you are ready to use the tool again, charge the battery pack until the left indicator light turns green on the charger or all 4 LED indicators turn green on the battery.
• Disconnect the product from the power supply
(i.e., remove the plug from the power supply or the battery pack) and check for damage after use.
• Do not store the tool with the battery pack installed.
• Clean all foreign material from the product.
• When not in use, store the tool, battery pack, and battery charger out of the reach of children.
• Keep the tool, battery pack, and battery charger away from corrosive agents, such as garden chemicals and de-icing salts.
• To reduce the risk of serious personal injury, do not store the battery pack outside or in vehicles.
• Store the tool, battery pack, and battery charger in an enclosed clean, dry area.
3.
Replace the skid plate and secure it using the 2 screws removed previously.
Preparing the Battery Pack for Recycling
Important: Upon removal, cover the terminals of the battery pack with heavy-duty adhesive tape.
Do not attempt to destroy or disassemble the battery pack or remove any of its components.
Lithium-ion battery packs labeled with the
Call2Recycle seal can be recycled at any participating retailer or battery recycling facility in the Call2Recycle program (US and Canada only). To locate a participating retailer or facility closest to you, please call
1-800-822-8837 or visit www.call2recycle.org.
If you cannot locate a participating retailer or facility nearby, or if your rechargeable battery is not labeled with the Call2Recycle seal, please contact your local municipality for more information on how to responsibly recycle the battery. If you are located outside of the US and Canada, please contact your authorized
Toro distributor.
17
Troubleshooting
Perform only the steps described in these instructions. All further inspection, maintenance, and repair work must be performed by an authorized service center or a similarly qualified specialist if you cannot solve the problem yourself.
Always remove the battery from the tool when troubleshooting, inspecting, maintaining, or cleaning the tool.
Problem
The tool does not start.
The tool does not reach full power.
The tool is producing excessive vibration or noise.
The edger stops during use.
The battery pack loses charge quickly.
The battery charger is not working.
The LED indicator light on the battery charger is red.
The LED indicator light on the battery charger is blinking red.
1. The battery is not fully installed in the tool.
Possible Cause
2. The battery pack is not charged.
Corrective Action
1. Remove and then replace the battery into the tool, making sure that it is fully installed and latched.
2. Remove the battery pack from the tool and charge it.
3. Replace the battery pack.
4. Contact an Authorized Service Dealer.
3. The battery pack is damaged.
4. There is another electrical problem with the tool.
1. The battery pack charge capacity is too low.
2. The air vents are blocked.
1. There is debris on the cutting head of the edger.
2. The blade is not properly tightened.
1. The depth is set too low.
2. Walking or cutting too fast.
1. The battery pack is over or under the appropriate temperature range.
1. The battery charger is over or under the appropriate temperature range.
2. The outlet that the battery charger is plugged into does not have power.
1. The battery charger and/or battery pack is over or under the appropriate temperature range.
1. There is an error in the communication between the battery pack and the charger.
2. The battery pack is weak.
1. Remove the battery pack from the tool and fully charge the battery pack.
2. Clean the air vents.
1. Clean any debris off from the cutting head area.
2. Tighten the blade.
1. Raise the depth of cut.
2. Slow your pace so the machine can work effectively.
1. Move the battery pack to a place where it is dry and the temperature is between 5°C (41°F) and 40°C (104°F).
1. Unplug the battery charger and move it to a place where it is dry and the temperature is between 5°C (41°F) and 40°C (104°F).
2. Contact your licensed electrician to repair the outlet.
1. Unplug the battery charger and move the battery charger and battery pack to a place where it is dry and the temperature is between 5°C (41°F) and 40°C (104°F).
1. Remove the battery pack from the battery charger, unplug the battery charger from the outlet, and wait 10 seconds. Plug the battery charger into the outlet again and place the battery pack on the battery charger. If the LED indicator light on the battery charger is still blinking red, repeat this procedure again. If the LED indicator light on the battery charger is still blinking red after 2 attempts, properly dispose of the battery pack at a battery recycling facility.
2. Properly dispose of the battery pack at a battery recycling facility.
18
Problem
The tool does not run or run continuously.
Possible Cause
1. There is moisture on the leads of the battery pack.
2. The battery is not fully installed into the tool.
Corrective Action
1. Allow the battery pack to dry or wipe it dry.
2. Remove and then replace the battery into the tool making sure that it is fully installed and latched.
19
California Proposition 65 Warning Information
What is this warning?
You may see a product for sale that has a warning label like the following:
WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov.
What is Prop 65?
Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into
California. It mandates that the Governor of California maintain and publish a list of chemicals known to cause cancer, birth defects, and/or other reproductive harm. The list, which is updated annually, includes hundreds of chemicals found in many everyday items. The purpose of Prop 65 is to inform the public about exposure to these chemicals.
Prop 65 does not ban the sale of products containing these chemicals but instead requires warnings on any product, product packaging, or literature with the product. Moreover, a Prop 65 warning does not mean that a product is in violation of any product safety standards or requirements. In fact, the
California government has clarified that a Prop 65 warning “is not the same as a regulatory decision that a product is ‘safe’ or ‘unsafe.’” Many of these chemicals have been used in everyday products for years without documented harm. For more information, go to https://oag.ca.gov/prop65/faqs-view-all .
A Prop 65 warning means that a company has either (1) evaluated the exposure and has concluded that it exceeds the “no significant risk level”; or (2) has chosen to provide a warning based on its understanding about the presence of a listed chemical without attempting to evaluate the exposure.
Does this law apply everywhere?
Prop 65 warnings are required under California law only. These warnings are seen throughout California in a wide range of settings, including but not limited to restaurants, grocery stores, hotels, schools, and hospitals, and on a wide variety of products. Additionally, some online and mail order retailers provide Prop 65 warnings on their websites or in catalogs.
How do the California warnings compare to federal limits?
Prop 65 standards are often more stringent than federal and international standards. There are various substances that require a Prop 65 warning at levels that are far lower than federal action limits. For example, the Prop 65 standard for warnings for lead is 0.5 μg/day, which is well below the federal and international standards.
Why don’t all similar products carry the warning?
•
Products sold in California require Prop 65 labelling while similar products sold elsewhere do not.
•
A company involved in a Prop 65 lawsuit reaching a settlement may be required to use Prop 65 warnings for its products, but other companies making similar products may have no such requirement.
•
The enforcement of Prop 65 is inconsistent.
•
Companies may elect not to provide warnings because they conclude that they are not required to do so under Prop 65; a lack of warnings for a product does not mean that the product is free of listed chemicals at similar levels.
Why does Toro include this warning?
Toro has chosen to provide consumers with as much information as possible so that they can make informed decisions about the products they buy and use. Toro provides warnings in certain cases based on its knowledge of the presence of one or more listed chemicals without evaluating the level of exposure, as not all the listed chemicals provide exposure limit requirements. While the exposure from Toro products may be negligible or well within the
“no significant risk” range, out of an abundance of caution, Toro has elected to provide the Prop 65 warnings. Moreover, if Toro does not provide these warnings, it could be sued by the State of California or by private parties seeking to enforce Prop 65 and subject to substantial penalties.
Rev A
Herunterladen
Öffentlicher Link aktualisiert
Der öffentliche Link zu Ihrem Chat wurde aktualisiert. Sie können Ihre Chat-Links nach der Registrierung hier einsehen und verwalten.
Öffentlicher Dokumentenlink
Werbung