- Sports & recreation
- Fitness, gymnastics & weight training
- Treadmills
- Toorx
- MIRAGE S60
- Owner's manual
advertisement
INSTRUCTION
EXPLODED DRAWING
- 5 -
15
22
23
24
25
16
17
18
19
20
21
30
31
32
33
26
27
28
29
34
35
PART NO
1
2
3
4
5
6
11
12
13
14
7
8
9
10
PARTS LIST
PART NAME
Front roller
Running belt
Rear roller
Running deck
1
Side rail
Fix cushion of running deck
Rubber cushion of running deck
Motor belt
Motor
Motor cover
Motor frame
Left end cap
Right end cap
Rear left level frame cover
Rear right level frame cover
Rear support cover
Rear adjustable foot
Running platform
Motor belly
Motor control board
Incline motor
Power wire
Motor adjustable plug
Power wire cushion
Fuse
Power switch
Incline frame
Incline frame shaft sleeve
Connect sleeve of Base frame
Damper
Base frame
Move wheel of base frame
Right inside protect cover
Right outside protect cover
Left inside protect cover
- 6 -
1
1
1
1
1
1
2
1
1
1
1
1
1
4
1
1
1
2
2
1
1
1
Q'TY
4
1
1
1
1
1
1
1
2
4
1
1
1
1
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
53
54
55
56
57
58
36
37
38
39
40
41
42
49
50
51
52
43
44
45
46
47
48
Left outside protect cover
Right upright
Left upright
Console frame
Handlebar down support
Foam
Right heart rate handle fix tube
Left heart rate handle fix tube
Heart rate handle
Aluminum top cap
Right cap frame
Right up cover of handle
Right up cover of main body
Right down cover of main body
Fix tube of heart rate handle
Right down cover of handle
Left cap frame
Left up cover of main body
Left down cover of main body
Left up cover of handle
Left down cover of handle
Press key up cover
Connect cover of handle
Press key panel
Press key down cover
Incline code switch
Code switch fix board
Safety key
Safety key fix board
Speed code switch
Encoder knob
Console down cover
Console frame
Fan adjustable board
Fan adjustable press board
Console up cover
Console LED panel
Phone frame
- 7 -
1
1
1
1
1
2
1
2
1
1
1
1
2
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
2
1
1
2
2
1
1
1
1
105
106
107
108
109
110
111
85
86
87
88
81
82
83
84
89
90
91
92
93
74
75
76
77
78
79
80
94
95
96
97
98
99
100
101
102
103
104
Display overlay
Press key overlay
Control board of console
2 inches of the horn
1.5 inches of the horn
Wind scooper
Fan
USB board
Control wire1
Control wire2
Control wire 3
Control wire 4
Magnet ring
Side rail cushion
Handle protect cover
Filter
M8*50 Allen head bolt
Φ8 Washer
M8*85 Allen head bolt
M8*65 Allen head bolt
M8*25 Allen head bolt
ST4.2*15 Screw
M8*20 Allen head bolt
Φ8 spring Washer
M8*12 bolts
ST4.2*10 Screw
ST4.2*15 Screw
ST4.8*16 Screw
ST4.8*16 Screw
M8*30 bolts
Φ16 plastic Washer
M8 Lock Nut
M10*50 Allen head bolt
Φ13 plastic Washer
M10 Lock Nut
M10*90 Allen head bolt
M8*45 Allen head bolt
- 8 -
2
9
1
2
2
1
1
2
4
4
16
1
1
21
6
6
2
6
1
2
16
2
1
1
1
1
2
2
1
3
1
1
1
17
18
2
2
119
120
121
122
123
124
125
126
127
128
112
113
114
115
116
117
118
M8*30 Allen head bolt
M8*40 Allen head bolt
M10*40 Allen head bolt
M8*25 Allen head bolt
M8*25 Allen head bolt
Φ8 Arc Washer
ST4.2*15 Screw
M10*30 Allen head bolt
Φ10 Washer
M8*35 Allen head bolt
M8*15 Allen head bolt
ST2.9*8 Screw
M4*16 bolts
M4 Lock Nut
M8*60 Allen head bolt
M8*35 Allen head bolt
ST4.2*30 Screw
HARDWARE COMPARISON CHART
For your convenience, we have identified the hardware used in the assembly of this product. The chart below is provided to help you to identify items that may be unfamiliar to you.
62
2
2
1
4
4
4
2
4
12
2
4
2
6
8
2
65
NO.
92
115
116
117
118
127
A
B
C
D
DESCRIPTION
Φ8 Washer
M8*25 Allen head bolt
M8*25 Allen head bolt
Φ8 Arc Washer
ST4.2*15 Screw
M8*35 Allen head bolt
5mm SOCKET HEAD WRENCH
6mm SOCKET HEAD WRENCH
SCREWDRIVER
LUBRICANT
Q'TY
10
6
8
2
6
4
1
1
1
1
- 9 -
ASSEMBLY INSTRUCTIONS :
WARNING: Please put on all the screws, washers and bolts then tighten them.
STEP1:
Fix upright onto the base frame with
M8*25 Allen head bolt 115, M8*25
Allen head bolt 116 and
Φ8 Arc
Washer 117.
- 10 -
STEP2:
Fix the console onto the upright with
M8*25Allen head bolt116 and Φ8
Washer92 .
- 11 -
Connect all cable .
A. Main connection cable
B. Incline handlebar button cable
C. Speed handlebar button cable
D. Pulse cable
E. Pulse cable
F. Safety key cable
G. Cockpit cable
- 12 -
STEP3:
Fix the protect cover of upright onto the base frame with ST4.2*15
Screw118.
STEP4:
Fix the handle protective cover on the upright with ST4.2 * 15 Screw 50.
STEP5:
Fix console on the console frame with
Φ8 Washer92 and 127.
Folding illustration:
To unfold the treadmill:
Folding illustration:
To drop down treadmill:
1. Strike the damper.
2. Hold on to the top end covers and pull down the treadmill slowly on the ground.
- 13 -
To fold up the treadmill:
Both hands hold on the bottom end covers and lift up the treadmill.
COMPUTER OPERATION
The Operation
OPERATION INSTRUCTION
Features a) Manual program
Run directly after pressing start b) Target program
Press the target button to set the countdown to set the target time, distance, calories, and number of steps. c) Fixed program (P01~P24)
Press PROGRAM to select the program, use the up/down arrows to scroll through the list
24 programs can be used to select and set the running time (default 99 minutes), from 5 minutes to 99 minutes.
The 24 procedures are as follows:
6 only change speed
12 speeds and lifts all change
6 only up and down changes d) User mode
User mode U1~U4, manual input time, speed and lift e)HRC
There are 4 programs (HRC1, HRC2, HRC3, HRC4) HRC, you can set the time, age, weight, and display the maximum heart rate of the current program
The maximum heart rate is calculated as 220-age, and the user can adjust it with the up and down arrows
HRC1: 60% max
HRC2: 70% max
HRC3: 80% max
HRC4: 90% max
In HRC mode, the treadmill will only detect the heart rate through the chest strap. f) Body Fat
Measure fat percentage
2 operation
Make sure the security key is inserted well, otherwise, the console will display "--" a) Boot
After inserting the security key, turn on the power, the console displays the version number and TOTAL value. Then standby, default program: manual mode
- 14 -
Start 1.0km/h-0.0 lift, the user can freely change the speed/lift, the default maximum time is 99 minutes b) start running
After standby or program setting, press <;Start>;, count down with 3-2-1 (3s), and then start running. c) Stop running
During operation, press <;stop/pause>;, the motor and lifting motor stop
The first time the user presses stop/pause the treadmill, we pause and hold it for 2 minutes, then it will automatically stop and rise to 0.0
If you press stop/pause twice, the treadmill will stop, lift 0.0 and reset the data
When the safety switch is removed, the speed returns to zero. The slope is maintained.
When the safety switch is put on again, the slope returns to zero. d) Speed setting
When running, press speed +/- to increase/decrease speed by 0.1 or use smart ring to adjust 0.5/gear, speed adjustment range 1-maximum speed, speed shortcut keys <3>,
<6>, <9>, <12> Set speed directly e) Lift setting
When running, press up/down +/- to increase/decrease up/down 1, or use smart ring to adjust 1/gear, up/down adjustment range 0-15, up/down shortcut keys <3>, <6>, <9>,
<12 >Directly set the lift f) Set the target program
In the standby mode, press TARGET to switch to the setting target time, distance, calories, steps usage mode
The currently set target will flash as a notification, press the up and down arrows to adjust the target value,
Long press for continuous adjustment, then press Enter to confirm
Target time: default value 30:00; range 5:00-99:00; 1st gear = 1 minute
Target calories: default value 50; range 10-990; level 1=10 calories
Target step: default 4000; range 1000-9900; 1st gear=100 steps
During the setting process, press <START> to start running, the countdown reaches 0.0 and the treadmill stops g) Set up a fixed program
In the standby state, press <PROGRAMS>; the [PULSE] window will flash, the program number will be displayed, and the user will scroll up and down (P01-P24) to select the program. Press Enter to confirm
- 15 -
Press MODE to set the time, and then use the up/down arrows to set the time (the default time is 30:00 minutes), the range is 5:00-99:00 minutes h)HRC setting
Press HRC in standby
To select programs H1-H4, please use the up/down arrows and press Enter to confirm
• To adjust the value, press MODE
1) Set the time, the default value is 30 minutes, the range is 5~99 minutes-then press
Enter
2) Press MODE to set the age, the default value is 40, the range is 16-65-and then press Enter
3) Press MODE>; set the weight, the default value is 68 kg, the range is 40-130 kg-then press Enter
4) The suggested target will be displayed in the heart rate window, and the user can use the up/down arrows to change the value-then press Enter
Press <START>, the treadmill starts to run, the default speed is 1 km/h, and the time window displays the default value 30 or the set time.
When the time countdown reaches zero, the treadmill stops
The HRC program is only applicable to the chest strap, and the speed and lift will be adjusted according to the current heart rate compared to the target heart rate
• Speed change relationship
A: Change frequency, HRC detects heart rate every 30 seconds (heart rate is always displayed).
B: If the user's heart rate is lower than the target heart rate by 30 beats/min, the speed will increase by 2.0 km/h.
C: If the user's heart rate is 6-29 beats/min below the target heart rate, the speed will increase by 1.0 km/h.
D: If the user's heart rate is higher than the target heart rate by 30 beats/min, the speed will decrease by 2.0 km/h.
E: If the user's heart rate is 6-29 beats/min higher than the target heart rate, the speed will decrease by 1.0 km/h.
G: The user's heart rate is higher or lower than the target heart rate 0-5 beats per minute, and the speed remains the same.
4. In the following situations, decelerate to the minimum, run at the lowest speed for 15 seconds and then stop, and beep once every second.
A: The heart rate is detected every 30 seconds, if the heart rate is not detected twice in a row.
B: At a speed of 1 km/h, the exercise heart rate is greater than the target heart rate, resulting in deceleration.
C: When the heart rate exceeds (220-years old).
- 16 -
5. At speeds above 1 km/h, the deceleration cannot be lower than 1 km/h. For example, the minimum speed of the treadmill is 1 km/h, and when running at 1.6 km/h, the heart rate will decelerate by 1.0 (2.0) km/h. , Then decelerate to 1 km/h.
The slope is not controlled by the heart rate and can be adjusted manually.
The starting speed is 1 km/h, and the heart rate is not used for 1 minute before running.
Manual adjustment of speed and tilt is also available. The adjustment will be for the current 30 segments. When passed to the next step, the speed/tilt value will follow the
HRC rules. Press the mode and the user can stop the HRC and run in the manual program i) 【 USER setting
In the standby mode, press USER
Press ENTER to set the time. Press ENTER again to confirm or START to directly start
USER program operation.
The following is the setting method of 30-segment data of USER program
1) Press the MODE button to enter the data setting step. The data in the first column flashes to enter the editing state, press the speed +/- or use the speed shuttle switch to set the speed value. Press the slope +/- or the slope shuttle switch to set the slope value. The speed defaults to 1.0. The slope defaults to 0. Press ENTER to confirm to enter the next block.
2) The second step will flash-repeat all 30 steps
3) After setting all the 30-segment programs, press ENTER to return to the flashing state of the USER name, indicating that all the data has been recorded. At this time, you can press ENTER to set the running time. You can also directly press START to directly start running. Countdown at 0:00, the treadmill stops j) 【 Body Fat 】 Test mode
Press BODY FAT in standby mode to enter the fat measurement mode
Energy window display: gender, default value: S-1, setting range: 1-2 1 = male 2 = female
Distance window display: age, default value: 25 years old, setting range: 10-99 years old
Steps window display: height, default value: 170cm, setting range 100-220cm
Speed window display: weight, default value: 70kg, setting range 20-150kg
1) Press MODE to enter the settings, use the up/down arrows to adjust gender, age, height and weight
2) After the parameter setting is completed, press the MODE matrix window to display
0.0
- 17 -
3) At this time, put your hands on the heart rate grip, the matrix window will display the measured body fat value after 8 seconds..
k) fixed program diagrams,
TIME
MODE
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
P-01 SPD 1 3 3 4 5 5 4 4 3 3 2 3 3 4 5 5 4 4 3 3 3 3 4 5 5 4 4 3 3 1
P-02 SPD 2 4 6 6 6 5 4 4 4 3 3 4 6 6 6 5 4 4 4 3 4 6 6 6 5 4 4 4 3 2
P-03 SPD 2 4 6 7 7 6 6 5 5 3 4 6 7 7 6 6 5 5 3 4 6 7 7 6 6 5 5 4 3 2
P-04 SPD 2 4 6 8 6 6 5 5 4 4 3 4 6 8 6 6 5 5 4 4 3 4 6 8 6 6 5 5 3 2
P-05 SPD 3 4 6 8 10 8 6 6 5 5 4 4 6 8 10 8 6 6 5 5 4 4 6 8 10 8 6 5 3 2
P-06 SPD 3 4 6 8 10 12 10 8 6 5 4 6 8 10 12 10 8 6 5 4 6 8 10 12 10 8 6 5 3 2
P-07 spd 1 3 3 4 5 5 4 4 3 3 2 3 3 4 5 5 4 4 3 3 3 3 4 5 5 4 4 3 3 1 inc 0 3 3 4 4 6 6 4 4 3 0 3 3 4 4 6 6 4 4 0 3 3 4 4 6 6 4 4 3 0
P-08 spd 2 4 6 6 6 5 4 4 4 3 3 4 6 6 6 5 4 4 4 3 4 6 6 6 5 4 4 4 3 2 inc 0 3 3 5 5 6 6 5 5 3 1 3 3 4 4 6 6 4 4 0 3 3 4 4 6 6 4 4 3 0
P-09 spd 2 4 6 6 6 5 4 4 4 3 3 4 6 6 6 5 4 4 4 3 4 6 6 6 5 4 4 4 3 2 inc 3 5 3 5 9 4 2 4 6 8 10 10 5 5 5 4 4 6 7 8 7 4 4 4 5 7 7 6 4 0
P-10 spd 2 4 6 7 7 6 6 5 5 3 4 6 7 7 6 6 5 5 3 4 6 7 7 6 6 5 5 4 3 2 inc 5 4 4 3 3 4 4 3 3 10 8 6 6 4 3 4 5 6 10 8 6 3 3 5 5 3 3 5 4 0
P-11 spd 2 4 6 7 7 6 6 5 5 3 4 6 7 7 6 6 5 5 3 4 6 7 7 6 6 5 5 4 3 2 inc 7 5 4 3 4 5 5 4 4 8 7 9 9 5 5 4 6 6 8 7 6 6 3 3 4 6 6 4 4 0
P-12 spd 2 4 6 8 6 6 5 5 4 4 3 4 6 8 6 6 5 5 4 4 3 4 6 8 6 6 5 5 3 2 inc 6 4 4 3 4 4 5 6 7 7 10 8 6 5 6 7 9 7 8 10 10 8 6 5 7 7 10 8 5 0
P-13 spd 2 4 6 8 6 6 5 5 4 4 3 4 6 8 6 6 5 5 4 4 3 4 6 8 6 6 5 5 3 2 inc 5 7 7 5 7 4 6 6 7 8 10 10 3 3 5 5 7 7 8 8 10 8 6 4 6 6 8 8 10 0
P-14 spd 3 4 6 8 10 8 6 6 5 5 4 4 6 8 10 8 6 6 5 5 4 4 6 8 10 8 6 5 3 2 inc 5 4 4 3 3 4 5 5 8 10 8 8 6 4 3 4 6 6 8 8 10 10 8 4 3 4 8 8 10 0
P-15 spd 3 4 6 8 10 8 6 6 5 5 4 4 6 8 10 8 6 6 5 5 4 4 6 8 10 8 6 5 3 2 inc 6 5 6 5 4 6 8 8 9 9 10 10 6 5 4 5 6 6 8 8 10 10 6 5 4 6 8 8 10 0
P-16 spd 3 4 6 7 8 10 8 6 5 3 4 6 7 7 6 6 5 5 3 4 6 7 7 6 6 5 5 4 3 2 inc 8 8 6 5 6 5 6 8 8 10 10 8 6 4 6 6 8 8 10 8 6 5 5 8 6 8 10 10 12 0
P-17 spd 3 4 6 8 10 12 10 8 6 5 4 6 8 10 12 10 8 6 5 4 6 8 10 12 10 8 6 5 3 2 inc 8 8 6 5 4 3 4 5 6 6 10 6 6 4 3 4 6 8 10 12 10 8 4 3 4 6 8 10 12 0
P-18 spd 3 4 6 8 10 12 10 8 6 5 4 6 8 10 12 10 8 6 5 4 6 8 10 12 10 8 6 5 3 2 inc 10 9 8 7 6 5 6 7 8 10 12 8 7 6 5 6 7 8 10 12 10 8 6 5 6 7 8 10 12 0
P-19 INC 0 3 3 4 4 6 6 4 4 3 0 3 3 4 4 6 6 4 4 0 3 3 4 4 6 6 4 4 3 0
P-20 INC 3 5 3 5 9 4 2 4 6 8 10 10 5 5 5 4 4 6 7 8 7 4 4 4 5 7 7 6 4 0
P-21 INC 5 4 4 3 3 4 4 3 3 10 8 6 6 4 3 4 5 6 10 8 6 3 3 5 5 3 3 5 4 0
P-22 INC 6 5 6 5 4 6 8 8 9 9 10 10 6 5 4 5 6 6 8 8 10 10 6 5 4 6 8 8 10 0
P-23 INC 8 8 6 5 4 6 6 8 6 10 10 8 6 4 6 6 8 8 10 8 6 5 5 8 6 8 10 10 12 0
P-24 INC 10 9 8 7 6 5 6 7 8 10 12 8 7 6 5 6 7 8 10 12 10 8 6 5 6 7 8 10 12 0 l) Fan switch
1. Press the FAN switch to turn the fan on or off.
2. Use the button + below to increase from level 1 to level 2, and press it again to increase to level 3.
3. Use the button below-to decrease from level 3 to level 2, and then press it again to decrease to level
1. m) Bluetooth music
Turn on the phone's Bluetooth to pair with the searched Bluetooth device of the machine. After the connection is successful, use the mobile phone to play music.
- 18 -
GARLANDO SPA
Via Regione Piemonte, 32 - Zona Industriale D1
15068 - Pozzolo Formigaro (AL) - Italy www.toorx.it - [email protected]
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement