advertisement
MANUAL
ENGLISH
Mirrorball Motor DMX 2 channel V1
Ordercode: 60449
Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands
Mirrorball Motor DMX 2 channel
Table of contents
Ordercode: 60499 1
Mirrorball Motor DMX 2 channel
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure that all parts are present, and have been received in good condition. Notify the dealer immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be returned to the factory, it is important that the fixture be returned in the original factory box and packing.
Your shipment includes:
Showtec Mirrorball Motor DMX 2 channel
User manual
Safety Instructions
Every person involved with the installation, operation and maintenance of this device has to:
be qualified
follow the instructions of this manual
Before the initial start-up, please make sure that there is no damage caused by transportation.
Should there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes contained in this manual.
Please consider that damages caused by manual modifications to the device are not subject to warranty.
This device contains no user-serviceable parts. Refer servicing to qualified technicians only.
Ordercode: 60499 2
Mirrorball Motor DMX 2 channel
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual or any unauthorized modification to the device.
Never let the power cord come into contact with other cables! Handle the power cord and all connections with the mains with particular caution!
Never remove warning or informative labels from the unit. Do not open the device and do not modify the device.
Never use anything to cover the ground contact.
Never look directly into the light source. Never leave any cables lying around.
Never use the device during thunderstorms, unplug the device immediately. Never look directly into the light source.
Do not insert objects into air vents.
Do not connect this device to a dimmerpack.
Do not switch the device on and off in short intervals, as this would reduce the device’s life.
Do not touch the device’s housing bare-handed during its operation (housing becomes very hot).
Do not shake the device. Avoid brute force when installing or operating the device.
Only use device indoors, avoid contact with water or other liquids.
Only operate the fixture after having checked if the housing is firmly closed and all screws are tightly fastened.
Only operate the device after having familiarized with its functions. Avoid flames and do not put close to flammable liquids or gases.
Always disconnect power from the mains, when device is not used, before cleaning or when replacing lamp! Only handle the power cord by the plug. Never pull out the plug by tugging the power cord.
Make sure that the device is not exposed to extreme heat, moisture or dust. Make sure that the available voltage is not higher than stated on the rear panel.
Make sure that the power cord is never crimped or damaged. Check the device and the power cord from time to time.
If the external cable is damaged, it has to be replaced by a qualified technician.
If device is dropped or struck, disconnect mains power supply immediately. Have a qualified engineer inspect for safety before operating.
If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your device. Leave the device switched off until it has reached room temperature.
If your Showtec device fails to work properly, discontinue use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Showtec dealer for service.
For adult use only. The Mirrorball Motor must be installed out of the reach of children. Never leave the unit running unattended.
The user is responsible for correct positioning and operating of the Mirrorball Motor. The manufacturer will not accept liability for damages caused by the misuse or incorrect installation of this mirror ball control system.
This device falls under protection class I. Therefore it is essential to connect the yellow/green conductor to earth.
• Repairs, servicing and electric connection must be carried out by a qualified technician.
• WARRANTY: Till one year after date of purchase.
Ordercode: 60499 3
Mirrorball Motor DMX 2 channel
Operating Determinations
• This device is not designed for permanent operation. Consistent operation breaks will ensure that the device will serve you for a long time without defects.
• The minimum distance between light output and the illuminated surface must be bigger than 1 meter.
• The maximum ambient temperature t a
= 40°C must never be exceeded.
• The relative humidity must not exceed 50 % with an ambient temperature of 40° C.
• If this device is operated in any other way than the one described in this manual, the product may suffer damages and the warranty becomes void.
• Any other operation may lead to dangers like short-circuit, burns, electric shock, crash, etc.
You endanger your own safety and the safety of others!
Rigging
Please follow the European and national guidelines concerning rigging, trussing and all other safety issues.
Do not attempt the installation yourself !
Always let the installation be carried out by an authorized dealer !
Procedure:
• If the device is lowered from the ceiling or high joists, professional trussing systems have to be used.
• Use a clamp to mount the device, with the mounting bracket, to the trussing system.
• The device must never be fixed swinging freely in the room.
• The installation must always be secured with a safety attachment, e.g. an appropriate safety net or safety cable.
• When rigging, derigging or servicing the projector, always make sure, that the area below the installation site is secured and that there are not any unauthorized people around.
Improper installation can cause serious injuries and/or damage of property!
Ordercode: 60499 4
Mirrorball Motor DMX 2 channel
Connection with the mains
Connect the device to the mains with the power-plug.
Always check if the right color cable is connected to the right place.
International
L
N
EU Cable
BROWN
BLUE
YELLOW/GREEN
UK Cable
RED
BLACK
GREEN
US Cable
YELLOW/COPPER
SILVER
GREEN
Pin
PHASE
NEUTRAL
PROTECTIVE GROUND
Make sure that the device is always properly connected to the earth!
Improper installation can cause serious injuries and/or damage of property!
Ordercode: 60499 5
Mirrorball Motor DMX 2 channel
Return Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or mail [email protected]
and request an RMA prior to shipping the fixture.
Be prepared to provide the model number, serial number and a brief description of the cause for the return. Be sure to properly pack fixture, any shipping damage resulting from inadequate packaging is the customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper inside the box:
01) Your name
02) Your address
03) Your phone number
04) A brief description of the symptoms
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any shortcomings and/or visible defects, or perform this check after our announcement that the goods are at their disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to report and submit claims with the shipper in the event that a fixture is damaged due to shipping. Transportation damage has to be reported to us within one day after receipt of the delivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless agreed otherwise in writing.
Complaints against us must be prepared in writing or sent by fax within 10 working days after receipt of the invoice. After this period complaints will not be handled anymore.
Complaints will only then be considered if the client has so far complied with all parts of the agreement, regardless of the agreement from which the obligation is resulting.
Ordercode: 60499 6
Mirrorball Motor DMX 2 channel
Description of the device
Features
The Showtec Mirrorball Motor DMX 2 channel is a mirror ball control system.
Input Voltage: 100-240V AC, 60/50Hz
Power Consumption: 12W
Max. rotation speed: 5 RPM
Mirror ball max. size: 50 cm/10 kg
Control modes: Stand-alone, Master/Slave, DMX-512
DMX channels: 2 channels
Housing: Metal & Flame retardant plastic
Cooling: Convection
IP Rating: IP20
Dimensions: 205 x 135 x 100 mm (LxWxH)
Weight: 2 kg
Frontside
01) Mirror ball slot
02) Schuko power cable 100-240V
03) Reset button
04) Dip switches
05) Ground/earth connection
06) Schuko light fixture 60W OUT # 1
Ordercode: 60499 7
Fig. 01
Mirrorball Motor DMX 2 channel
Backside
Fig. 02
07) 3-pin DMX signal connector IN
08) 3-pin DMX signal connector OUT
09) Schuko light fixture 60W OUT # 2
10) Ground/earth connection
Installation
Remove all packing materials from the Mirrorball Motor DMX 2 channel. Check if all foam and plastic padding is removed. Connect all cables.
Do not supply power before the whole system is set up and connected properly.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.
Set Up and Operation
Follow the directions below, as they pertain to your preferred operation mode.
Before plugging the unit in, always make sure that the power supply matches the product specification voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa.
Connect the device to the main power supply.
Ordercode: 60499 8
Mirrorball Motor DMX 2 channel
Control Modes
There are 3 modes: • Stand-alone
• Master/Slave
• DMX-512 (2CH)
One Mirrorball Motor (Stand-alone)
01) Fasten the motor onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) When the Mirrorball Motor is not connected with a DMX-cable, it functions as a stand-alone device.
Dip switch # 10 must always be set to ON for Stand-alone control.
Stand-alone: Dip switch # 10 to ON position.
05) Set dip switches # 1-8 to ON position in order to set the rotation speed. The adjustment range is from slow to fast.
06) Set dip switch # 9 to ON position for clockwise rotation. If dip switch # 9 is in OFF position, the motor will rotate counterclockwise.
Multiple Mirrorball Motors (Master / Slave Control)
01) Fasten the motor onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) Use a 3-pin XLR cable to connect the Mirrorball Motors.
The pins: 01) Earth
02) Signal (-)
03) Signal (+)
05) Link the units as shown in (fig.03). Connect a DMX signal cable from the first unit's DMX "out" socket to the second unit's "in" socket. Repeat this process to link the second, third, and fourth units. This means that you can set your desired operation mode on the master device and all slave devices will react the same as the master device.
06) Set the dip switches on the master and slave devices as follows:
Master device: Dip switch # 10 to ON position.
The LED indicator next to the dip switches will light up red.
Slave devices: Dip switch # 10 to OFF position.
One of the dip switches # 1-9 to ON position.
The LED indicator next to the dip switches will blink.
07) On the master device, set dip switches # 1-8 to ON position in order to set the rotation speed. The adjustment range is from slow to fast.
08) On the master device, set dip switch # 9 to ON position for clockwise rotation. If dip switch # 9 is in
OFF position, the motor will rotate counterclockwise.
Ordercode: 60499 9
Mirrorball Motor DMX 2 channel
Multiple Mirrorball Motors (Master/Slave control)
Multiple Mirrorball Motors (DMX control)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Use a 3-pin XLR cable to connect the Mirrorball Motor and a light controller.
Fig. 03
04) Link the units as shown in (fig.04). Connect a DMX signal cable from the first unit's DMX "out" socket to the second unit's "in" socket. Repeat this process to link the second, third, and fourth units.
05) Set the dip switches on the master and slave devices as follows:
Master device: Dip switch # 10 to OFF position.
Dip switch # 1 to ON position.
Slave device: Dip switch # 10 to OFF position.
One of the dip switches # 1-9 to ON position.
The LED indicator next to the dip switches will blink.
Ordercode: 60499 10
Mirrorball Motor DMX 2 channel
06) Supply electric power: Plug the mains power cord into proper electric power supply sockets, starting with the first unit. Do not supply power before the whole system is set up and connected properly.
Multiple Mirrorball Motors DMX Set Up
Note : Link all cables before connecting electric power
Fig. 04
Ordercode: 60499 11
Mirrorball Motor DMX 2 channel
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to run synchronized shows of two or more fixtures set to a master/slave operating mode. The combined number of channels required by all the fixtures on a serial data link determines the number of fixtures the data link can support.
Important: Fixtures on a serial data link must be daisy-chained in a single line. To comply with the
EIA-485 standard, no more than 30 devices should be connected on one data link.
Connecting more than 30 fixtures on one serial data link without the use of a DMX optically isolated splitter may result in deterioration of the digital DMX signal.
Maximum recommended DMX data link distance: 100 meters
Maximum recommended number of fixtures on a DMX data link: 30 fixtures
Data Cabling
To link fixtures together, you must obtain data cables. You can purchase DAP Audio certified DMX cables directly from a dealer/distributor or construct your own cable. If you choose to create your own cable, please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic interference.
DAP Audio DMX Data Cables
• DAP Audio Basic microphone cable for allround use. bal. XLR/M 3-pin > XLR/F 3-pin.
Ordercode FL01150 (1,5 m), FL013 (3 m), FL016 (6 m), FL0110 (10 m), FL0115 (15 m), FL0120 (20 m).
• DAP Audio X-type data cable XLR/M 3-pin > XLR/F 3-pin. Ordercode FLX0175 (0,75 m),
FLX01150 (1,5 m), FLX013 (3 m), FLX016 (6 m), FLX0110 (10 m).
• DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL71150 (1,5 m), FL713 (3 m), FL716 (6 m), FL7110 (10 m).
• DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL7275 (0,75 m), FL72150 (1,5 m), FL723 (3 m), FL726 (6 m), FL7210 (10 m).
• DAP Audio 110 Ohm cable with digital signal transmission. Ordercode FL0975 (0,75 m),
FL09150 (1,5 m), FL093 (3 m), FL096 (6 m), FL0910 (10 m), FL0915 (15 m), FL0920 (20 m).
DMX Channels
2 Channels
Channel 1 – Lamp ON/OFF
0-127
128-255
Lamp OFF
Lamp ON
Channel 2 – Motor rotation
0
1-127
Not functional
Clockwise rotation, from fast to slow
128
129-255
Stop
Counterclockwise rotation, from slow to fast
Ordercode: 60499 12
Mirrorball Motor DMX 2 channel
Maintenance
The operator has to make sure that safety-related and machine-technical installations are to be inspected by an expert after every year in the course of an acceptance test.
The operator has to make sure that safety-related and machine-technical installations are to be inspected by a skilled person once a year.
The following points have to be considered during the inspection:
01) All screws used for installing the device or parts of the device have to be tightly connected and must not be corroded.
02) There may not be any deformations on housings, fixations and installation spots.
03) Mechanically moving parts like axles, eyes and others may not show any traces of wearing.
04) The electric power supply cables must not show any damages or material fatigue.
The Mirrorball Motor DMX 2 channel requires almost no maintenance. However, you should keep the unit clean.
Please clean internal components once a year with a light brush and vacuum cleaner.
Keep connections clean. Disconnect electric power, and then wipe the DMX and Schuko connections with a damp cloth. Make sure connections are thoroughly dry before linking equipment or supplying electric power.
Troubleshooting
This troubleshooting guide is meant to help solve simple problems.
If a problem occurs, carry out the steps below in sequence until a solution is found. Once the unit operates properly, do not carry out following steps.
No Light
If the mirror ball control system does not operate properly, refer servicing to a technician.
Suspect two potential problem areas as: the power supply and the motor.
01) Power supply. Check if the unit is plugged into an appropriate power supply.
02) The motor. Return the device to your Showtec dealer.
03) If both of the above appear to be O.K., plug the unit in again.
04) If you are unable to determine the cause of the problem, do not open the Mirrorball Motor, as this may damage the unit and the warranty will become void.
05) Return the device to your Showtec dealer.
Ordercode: 60499 13
Mirrorball Motor DMX 2 channel
Product Specifications
Model:
Input Voltage:
Power consumption:
DMX linking:
Dimensions:
Weight:
Operating and Programming:
Signal pin OUT:
DMX Mode:
Showtec Mirrorball Motor DMX 2 channel
100-240V AC, 60/50Hz
12W
30pcs
205 x 135 x 100 mm (LxWxH)
2 kg
Signal input:
Signal output:
Electro-mechanical effects:
Max. rotation speed:
Mirror ball max. size:
DMX-control:
Pin 1 (earth), pin 2 (-), pin 3 (+)
2 channels
3-pin XLR IN
3-pin XLR OUT
Control:
Housing:
Connections:
IP rating:
Cooling:
Max. ambient temperature t a
: 40°C
Max. housing temperature t
B
: 80°C
Minimum distance:
Minimum distance from flammable surfaces: 0,5 m
Minimum distance to lighted object: 1 m
5 RPM
50 cm/10 kg via standard DMX-controller
Stand-alone, Master/Slave, DMX512
Metal & Flame retardant plastic
Schuko power cable & Data connector
IP20
Convection
Design and product specifications are subject to change without prior notice.
Website:
www.Showtec.info
Email:
[email protected]
Ordercode: 60499 14
©2015 Showtec
advertisement