DownEaster Salt Spreader Owners Manual

 DownEaster
Salt Spreader
- Owners Manual
sk Gas
sie Hydraulic
>< Self Contained Hydraulic
1.6 to 6.0 yard Capacity
7-10 ft Hopper
December 2008
Coastal Metal Fab downeastermfg.com
120 Old Lisbon rd. Topsham, ME. 04086 (207)-729-5101 OM-Salt Spreader-Gas,Hydraulic, Self Contained
ET a |
INDEX
|. INTRODUCTION
Il. SAFETY WARNINGS
A) MODEL NO. BREAKDOWN
(II. INSTALLATION
A) HOPPER ASEMBLY
B) SPINNER & CHUTE ASSEMBLY
C) ELECTRICAL INSTALLATION
C) ELECTRICAL INSTALLATION
IV. MAINTENANCE
A) FUEL
B) LUBRICATION
C) BATTERY
V. OPERATION
A) PRE-STARTING CHECKS
B) ENGINE OPERATION
C) SPREADER OPERATION
VI. ADJUSTMENT 8
A) GATE ADJUSTMENT
B) CONVEYOR CHAIN ADJUSTMENT
C) CHUTE ADJUSTMENT
Vill. SHUT DOWN 8 STORAGE
A) STOPPING THE SPREADER
B) CONVEYOR CHAIN ADJUSTMENT
C) CHUTE ADJUSTMENT
Vil. WARRANTY
IX. HYDRAULIC PUMP INSERT
DETAILS AND PARTS LIST
CONVEYOR ASSEMBLY 12" & 14"
CHUTE & SPINNER ASSEMBLY
ENGINE PLATFORM ASSEMBLY
FEED GATE ASSEMBLY
SELF CONTAINED HYDRAULIC
MISC. PARTS LIST
HOPPER & SCREEN PARTS LIST
ACCESSORIES
6-7
7-8
9-10
11
12
12
12
13
13
14
15
15
15
16
17
18-19
20-21
22-23
24-25
26-27
28
23
|. INTRODUCTION
Thank you for purchasing DownEaster sand and salt spreader. This Owners anual provides
easy to follow instructions for installing, operating and servicing the spreader.
Read this entire manual carefully to learn the proper procedures for each operation. Follow all
of the instructions described to keep the sander in top condition and it will provide years of trouble-free
performance.
In the event that a problem should arise or that you have any questions about the spreader
please contact your DownEaster Dealer.
WARRANTY OVERVIEW
A Warranty is provided for original owners who maintain and operate their DownEaster sand
and salt spreader as described in this manual.
Proof of purchase is required for warranty service. Full warranty details are provided in the
chapter on warranty later in this manual. :
THE WARRANTY DOES NOT COVER THE FOLLOWING:
A DownEaster sand and salt spreader which has been altered or modified in any way not
approved by the manufacturer, including setting fuel delivery above specifications or otherwise
overpowering the engine.
Depreciation or damage caused by normal wear, accident, lack of reasonable and necessary
maintenance as specified in this manual, improper maintenance, improper storage protection,
or improper use or abuse.
Normal maintenance and replacement of service items such as filters, spark plugs, chains,
hoses, bearings, gears, sprockets, and battery unless such items are defective.
Transportation, shipping, and service call charges for warranty service.
All information, lilustrations, and specifications in this manual are based upon the latest
DownEaster sand and salt spreader information available at the time of publication. The right is
reserved to make changes without notice.
*** NOTE: Avoid large rocks from damaging the spreader mechanism. The sand screen must
always be in place on top of the hopper when loading sand or salt.
*** NOTE: Read this manual and fully understand the information presented before starting or
operating the equipment.
I. SAFETY WARNINGS
UNDERSTANDING SAFETY SYMBOLS
The purpose of safety symbols is to attract attention to possible dangers. The safety symbols
and explanations with them deserve your careful attention. The safety warnings do not by themselves
eliminate any danger. The instructions or warnings they give are not substitutes for proper accident
prevention measures.
SAFETY SYMBOL MEANING
I! DANGER Identifies the most serious hazards
WARNING Failure to obey a safety warning can result
in injury to yourself and others
*** NOTE Advises of general information or
instructions vital to the operation or
maintenance of the equipment
LEARN MACHINE SAFETY
Carefully read this manual. Learn how to safely operate the DownEaster spreader and how to
use the controls properly.
Do not allow anyone to operate the DownEaster spreader without proper training and
instruction.
Unauthorized modification to the DownEaster spreader may impair the function and/ or safety
of the machine.
FOLLOW SAFETY INSTRUCTIONS
Read all safety messages in this manual and on the DownEaster spreader safety labels.
Follow recommended precautions and safe operating practice.
Maintain all safety labels on the DownEaster spreader in good condition. Replace missing or
damaged safety labels with new labels available through your DownEaster dealer.
SAFETY LABELS
т я РР AT ВЕ CERO T pm a ripe Ta
y "fe ne A ra e EEE - E a - ==. ae Я Ней Jeg EE AEM EEE E
re AA Ен: oy eT} yi rica Mo gag аа SR т TM : ST = a
ma E ri a Se EN a 1 Е : E Е E 3 HL ke I
E A : a Ta Ea E a Pe: + A ДР | я FC note т o CR Te fe 4
J вон ¥ = re, qe ee В bes PA: a Je LEE г by обе CCE Ty С
A Ч = He ñ de em тр. a. CCR Se CE he a = Ё FE 5 =
ar e ha Tt rm rT a 1 E HA TE A а 44 ; г а +
* y o ae A Le P 5 E a AA С
АЕ DS EEE “5 ff ы С IF = wf - =
* F HJ % = . Pl" 1 3 EEC т 3
(rie я + pe X 0 or
En a A Pian AR
я À É EAT
ы ho! abs! Tm д a Ta a 8
I y i ra LL = E
4 pr A ME ura Ч = p=
ne EEE ALEA ИР : с m
y РЗ, |
Г я Cac Pi pe ag = = "E
de,
STAY AWAY FROM THIS AREA WHILE MACHINE IS RUNNING.
DO NOT MAKE ANY 4D JUSTMENTS UNTIL MOTOR IS OFF,
CONVEYOR AND SPINNER STOPS.
DO NOT RISK [INJURY OR DEATH.
Hopper - Front, Outside Above Conveyor
Chute Bin - Rear, Outside Above Deflector
Fi TAIANA ELL
= я 3
= oo pe EB 5-2 = = F,
Sar BY 7e men =
Ae SERTE AL
7 by Ft 55 ‘ ha В
я = TOR e ' " E o т В
я a Ted La . e e EE
re + Я ела 154 6
a: a PTE =k B
: ee rm me п що A E В
+ ES
APTA
ty, A e e Ln TE E A
CHATTEN EI
itis YOUR RESPONSIBILITY to READ, UNDERSTAND,
and FOLOW safe operating practices defined in the
OPERATORS MANUAL shipped with the unit. FAILURE
to do so may result in PERSONAL INJURY to you or
others. If the manual is missing, obtain a replacement
from your dealer or the company-
ro Be mh rt
Eee ITA TE NO COOL Fw
Hopper - Rear, Outside at Left Top
KEEP THIS COVER CLOS ED
WHEN MACHINE 15
IN OPERATION
ee
| Engine Housing - Left Side Above Latch |
Page 4
SAFETY WARNINGS (continued)
PRE-OPERATIONAL
Thoroughly inspect the DownEaster spreader for loose or damaged parts before each use.
Do not use until adjustments or repairs are made.
Keep all bystanders, especially children and pets, at least 33 feet away from the area where
the machine will be operated.
FUELING
I WARNING Gasoline is extremely flammable and its vapors can explode if they are ignited.
Always stop the engine and allow it to cool before filling fuel tank. Keep sparks and open flame away
from the area.
OPERATIONAL
Wear safety glasses or goggles at all times when operating the spreader.
Keep hands, face and feet away from all moving parts. Do not attempt to stop the machinery
when it is rotating. |
Wear an effective hearirig protection device, such as earmuffs or earplugs to protect against
loud noise. Prolonged exposure to loud noise can cause impairment or loss of hearing.
Do not wear loose fitting clothing articles such as scarves, strings, chains, ties, etc. because
they could get drawn into the rotating machinery associated with this equipment. Long hair should be
tied back or protected from entanglement.
Do not touch the muffler. Engine and exhaust parts get extremely hot during operation and
remain hot for a period of time after the engine is turned off.
Always remain alert. To prevent serious injury to yourself and to others, do not operate this
equipment if you are fatigued.
Always stop engine when moving from one area to another.
SERVICING
Wear snug fitting clothing and appropriate safety protection equipment when operating or
working on the spreader. |
Before making repairs or adjustments disengage the clutch and stop the engine at the cab
control panel.
Keep the spreader and attachments in good working condition with all safety devices in place
and operational.
Store the spreader in a dry location away from areas where children play.
DownE aSter 5€ SAND AND SALT SPREADERS
MODEL NO. BREAKDOWN
D -
| — =
Material Hopper Capacity Hopper Length ‚Drive
S= Stainless Steel 16 = 1.6yd 07 = 7ft Blank = Gas
P= Painted 19=19yd 08=8ft H = Hydraulic
21 = 2.1yd 09 = oft
25=25yd 10=10f
30 = 3.0yd
33 = 3.3yd
37 = 3.7yd
40 =4.0yd
45= 4 .5yd
50= 5.0yd
60= 6.0yd
— SERIAL NO'S STARTING AT 1210 AND LATER
Serial no. |.D. Plate located on engine mount rear face.
5A
Il. INSTALLATION
A. HOPPER ASSEMBLY
*** NOTE: The DownEaster sand and salt spreader may be installed into the bed of a pickup
truck. It is the responsibility of the owner to determine the suitability of any installation configuration
relative to the load carrying capacity of a particular vehicle. The weight allowance of the empty
DownEaster spreader can be found in the chart of Hopper Specifications on the color brochure
included herein.
1. Remove the tailgate and/or any other obstructions from the bed of the truck.
2 Remove the hopper screen and any loose parts, which may have been shipped with or
stored in the hopper.
3. Remove any wood skids or shipping pallet attached to bottom of spreader.
4. Lift the hopper assembly by attaching your lifting device to the factory installed lifting eye
located inside the top of the hopper.
IWARNING: Empty the hopper before lifting. Do not attempt to lift the
spreader with the hopper containing any left over sand or salt.
5. Place the spreader onto the bed of the truck sliding it forward to the point that the rear of the
conveyor rails extend approximately one foot beyond the rear bumper of the truck. This temporary
location will allow for installation of the chute and spinner assembly.
B. SPINNER and CHUTE ASSEMBLY
1. Install the chute assembly onto the spreader using (4) 3/8" x 1" bolts, with lock washers
under the heads followed by flat washers, into the welded nuts at the bottom rear of conveyor rails.
2. Install the spinner shaft assembly into the chute slots using the (4) 3/8" x 1-1/2" bolts
through the spinner bearing pillow blocks from the inside to the outside of the chute including a flat
washer under the head and flat washer under the lock washer before adding nuts. Do not tighten nuts
at this time.
3. Install the spinner drive roller chain from the spinner sprocket to the gearbox sprocket using
the master link provided.
4. Adjust the spinner shaft location in the adjustment slots. Align the two sprockets to be in
the same plane. Tension the roller chain to have 5/16” deflection. Tighten the adjusting bolts.
Recheck the chain tension.
lll. INSTALLATION (continued)
5. Install the spinner disc onto the spinner shaft using the clevis pin and cotter pin to fasten the
assembly. :
6. Install the chain guard using (3) 1/4” x 3/4” bolts, flat washers at both sides, and locknuts.
C. TIE-DOWN INSTALLATION
1. After completing installation and adjustment of spinner and chute, reposition spreader
forward on truck bed so that chute just clears rear bumper of truck.
2. Bolt spreader to bed of truck, if necessary, through the four mounting holes provided in feet
at base of conveyor.
3. The DownEaster spreader may have been purchased with four optional strap and ratchet
tie-downs. Attach the hook end from each ratchet through the welded eye at each of the top outside
corners of the hopper. Attach the opposite end of each strap to an appropriate anchor point on the
truck. Tighten ratchets. :
D. ELECTRICAL INSTALLATION OF KEYLOCK PANEL OR ENCLOSED BOX
™* NOTE: If using the keylock controls, install the panel with the (2) 1/4” x 3/4” bolts, lock washers
and nuts provided. Be sure to ground the console panel to the vehicle chassis. If necessary, adda
ground wire from the mounting bolt to a ground point on the vehicle.
7" NOTE: . If using the box controls, connect the 2-conductor cable to a suitable electrical power
source on the vehicle; black to power and white to ground.
1. Route the 6-wire cab harness into the cab of the vehicle to the control panel console. Entry
into the rear of the cab may be made by drilling a 3/4” hole and installing the grommet
provided or through a split rear window if so equipped. Then route the cable under the seat
and along the floor to the console.
— NOTE: Care should be taken so that the harness is not chaffed by sharp edges.
2. Install wire connections from cab wiring harness to rear of switches as shown in the
appropriate wiring diagram on the following pages.
3. Secure the wiring harness to the vehicle behind the control panel using the plastic cable ties
so that no pressure is on the wire terminals and the wire will not slip.
4. Connect the cab wire harness to the sander wire harness at the 7-way plug.
Seven » Conductor - Wiring Harness
{Raar View of Switches) 6 WAY PLUG
; BLUE - CLUTCH]
a я [RED - THROTTLE
! | GREEN - GROUND |
| BROWN - THROTTLE |
LT LL
| BLACK - KILL |
een] YELLOW - SOLEMCOD|
Г {WHITE - CHOKE LIGHT ]
| i 1 WAY PLUG
PLUG
+
GRE E М linde AAA or cb lie a pe i fro han Board, ing mle
CHORE
INDICATOR
LIGHT
Ou
AA
cba:
TE eee
E
e ; A : A y e re = - h Al
E = = hoc =r y LE e - JT La =;
| . . 35 , ci
3 г ; в Hi
+ = 7 3
HT
E
E
po Cad
FEE
+. ri
TN E
Le y UP г т
Has ram arm me TALE RR
THROTTLE
ENGINE
CLUTCH
BLACK
‘NEGATIVE | POSITIVE
- |
#
IV. MAINTENANCE
A. FUEL
*** NOTE: Be sure to read these instructions in addition to the Briggs & Stratton Operator/Owner
Manual included before attempting to start or operate the unit.
1. Using old or improper fuel can cause engine damage, which may void the engine warranty.
2. Use clean, fresh, lead-free automotive gasoline with a minimum of 77 octane purchased
from a reputable supplier.
3. The use of gasoline containing alcohol is not recommended. Do not mix oil with gasoline.
4. Store fuel in a clean airtight container in a protected area away from buildings. Keep dirt,
scale, water or other foreign material out of fuel.
WARNING: Gasoline is extremely flammable and its vapors can explode if they are ignited. Always
stop the engine and allow it to cool before filling the fuel tank. Keep sparks and open flames
away from the area.
B. LUBRICATION
1. Engine: Use high-grade quality detergent oil classified “For Service SC, SD, SE, SF, SG”
such as Briggs & Stratton Warranty Certified SAE 30 oil; part no. 100005. Use no special additives.
2. Check the engine oll level every 5 hours or daily before starting engine.
3. Change and add engine oil according to the chart provided in the Briggs & Stratton Owner's
Manual. Do not overfill.
4. Gearbox: Use gear lube EP 80-90 weight oil. Fill the unit to the level plug.
5. Check the lubricant level before the unit is put into service and periodically thereafter.
6. Change the lubricant after the first 100 hours of use, or 30 days of operation. Thereafter,
normal change periods of 1000 hours or 12 months should be observed. It is recommended that the
lubricant be changed at the end of each season of use to remove moisture and corrosive
contaminants.
DownEaster >k
B. LUBRICATION
(CONTD)
A
ae)
| ee Drive Shaft Bearing
\ Ш
Electric Clutch
У ОГ
Gearbox Bearing Take Up Bearing
Spinner Shaft
Conveyor Chain
LUBE TYPE: Cold Weather Multi purpose Grease
APPLICATION: Every 25 hrs or Monthly
ELECTRIC CLUTCH
Post Season, remove and clean clutch.
Coat both mating surfaces of the clutch with oil or light grease.
Pre-Season: Remove oil or light grease prior to using clutch again.
10
C. BATTERY
There are 2 possible battery styles that may be used in downEaster salt and sand
spreaders. Although the batteries are functionally equivalent, they are sized
differently. Because of the different size, they will mount differently.
You can easily identify which battery fits a sander. Sanders that accept the larger
battery have two threaded posts to hold the battery in place.
The smaller Battery fits between the threaded posts. Secure the battery in place
using the hold-down bracket and connect the red battery cable to the positive
terminal and the black cable to the negative terminal.
The larger Battery fits in the tray located beneath the motor mount. The battery
must be placed on it's "side" in the tray with the posts facing the rear. Connect the
red battery cable to the positive terminal and then slide battery into the tray.
Next, connect the black cable to the negative terminal.
11
V. OPERATION
A. PRE-STARTING CHECKS
*** NOTE: Read and understand the Briggs é Stratton Owners Manual provided before
starting the engine.
1. Check fuel level before operating unit.
2. Check engine oil level before each use.
3. Lubricate conveyor and spinner as per maintenance schedule.
4. Check tension adjustments on conveyor, spinner, and gearbox chains.
5. Visually inspect the complete spreader for damage or loose fastenings.
6. Set hopper gate to desired feed rate.
7. Set internal and external chute adjustments to desired pattern.
IWARNING: Never adjust external spinner deflectors while spinner is in operation.
B. ENGINE OPERATION
—** NOTE: The DownEaster sand and salt spreader has been supplied with an electric throttle control
and electric clutch. For best results be sure to read and understand the following instructions for
choking and starting the engine:
- 1, Turn on vehicle ignition switch.
2. If so equipped, turn on the spreader ignition key switch.
3. Switch off the clutch engage control.
4. Press and hold the throttle control switch to the choke position for 5 seconds.
5. Activate engine switch to the start position to engage starter motor.
*** NOTE: Short cranking cycles (15 seconds. per min.) will extend starter life.
6. When engine starts, hold throttle control switch down to remove choke and set engine
speed to idle.
C. SPREADER OPERATION
1. Run engine for one minute to warm up. Reset idle speed If necessary.
2. Engage electric clutch to begin conveyor and spinner operation.
*** NOTE: Do not engage clutch with engine running at high speed. Damage to spreader can
result.
3. Set throttle to desired engine speed for spreader operation
Vi. ADJUSTMENTS
A. GATE ADJUSTMENT
1. Tighten bolt (A) just enough to provide friction to hold the gate in place.
2. Adjust the gate to the desired opening by moving e e gate handle either
down (increase) or up (decrease) to regulate the volume of sand being fed to the
spinner.
3 Tighten the wingged nut (B) when desired volume of sand is achieved.
Handle
Rear View
B. CONVEYOR CHAIN TENSION ADJUSTMENT
WARNING: Adjust the conveyor chain with the engine off
1. Loosen the 3/4" locking nuts at either side of the left and right conveyor idler
shaft adjustment brackets.
2. Turn each threaded rod by the welded nut at its free end to loosen or tighten
each side of the conveyor chain.
3. The conveyor chain is correctly adjusted when, under hand-pressure
deflection, there is 1/16" clearance between each side of the chain and the first
conveyor support angle closest to the idler shaft
4. Tighten the locking nuts on either side of each adjustment bracket.
Conveyor Support Angle
Take-up bolls
Side View
VI. ADJUSTMENTS (cont)
CHUTE ADJUSTMENT
The INTERNAL BAFFLES can be adjusted by the (2) Looped handles indexed into holes on rear of chute,
(1) Standing behind Chute, Pull each handle out of each adjustment hole.
(2) Rotating the handle up puts the Baffle into the flow of material.
(3) Refer to diagram below to get the desired pattern, and reset the handle into closest hole position.
Internal Baffles (Looking Down)
A
Laia Le AT FRA
e
я
Both internal baffles down. Left baffle down, Right up Right baffle down, Left up
чодоэла чзеа
uonoalg ued
The EXTERNAL BAFFLES are adjusted by lossening the locknuts on the hinges of each baffle
at the bottom of the chute.
(1) Loosen Locknuts and adjust to the desired pattern as shown below.
(2) Retighten Locknuts at each hinge to secure.
External Baffles
All baffles adjusted down Right baffle deflects material Right baffle deflects material
for a confined spread down. Heavy on right side. down. Heavy on right side.
pattern.
14
VII. SHUT DOWN & STORAGE
A. STOPPING THE SPREADER
1. Hold down the throttle control switch to reduce engine speed to an idle.
2. Switch the clutch engage switch to the “off” position.
3. Turn off the engine.
7 NOTE: Do not allow the contents of the hopper to freeze solid by standing without
operating the spreader for long periods during below freezing air temperatures. If this should
occur, do not attempt to operate the spreader. Move the spreader to a warm location and allow
the hopper contents to thaw before operating the spreader. Failure to observe these
precautions may result in damage to the equipment.
B..PREPARING THE SPREADER FOR STORAGE
1. Repair or replace all worn or damaged parts.
2. Lubricate all grease fittings and chains.
3. Wash the spreader to remove all residue and salt, especially in the hopper.
4. Clean the engine area to remove all grease and dirt from the housings.
5. Apply primer and paint to areas where finish has been chipped or abraded.
6. Remove the battery. Check electrolyte level, charge, and store in a cool, dry, safe-location.
'WARNING: Store battery where children cannot reach it.
7. Refer to the Briggs & Stratton Owner's Manual for storage requirements of the engine.
8. Prepare an area to store the spreader where it will be stable, off the ground, ina dry,
protected place. If stored outdoors, cover the spreader with a waterproof tarp.
C. REMOVING THE SPREADER FROM STORAGE
1. Charge battery, check electrolyte level, and reinstall on the spreader.
2. Check oil level and refuel engine.
3. Check oil level in the gearbox and refill if necessary.
4. Make sure that all shields and guards are in place before starting engine.
Coastal Metal Fab, Inc. Warranty
General Provisions Coastal Metal Fab, Inc. warrants its products to be free from manufacturing defects under
normal use and service conditions and will repair or replace, at its option, any products or components thereof
that are proven to be defective during the warranty period as specified below. This warranty extends to the
original retail purchaser only and commences on the date of original purchase. Coastal Metal Fab's maximum
liability under this warranty is limited to the cost of the repair or replacement of any defective products or
components, and excludes any incidental or consequential damages. The warranty period is as follows:
DownEaster brand Dump Trailers and Dump Inserts -- 2 years from date of purchase
DownEaster brand Salt- and Sandspreaders and all other Trailers -- 1 year from date of purchase
Items Warranted Separately This warranty does not apply to certain components that are warranted
separately by the original equipment manufacturers including, but not limited to, electric or gasoline motors,
hydraulic pumps, hydraulic cylinders, tires, wheels, and axles.
tems not Covered Coastal Metal Fab, Inc. is not responsible for the following:
e Premiums charged for overtime labor requested by the purchaser.
Transportation to and from the dealership or service calls made by the dealer.
Products purchased used.
Products that have been altered or modified in ways not approved by Coastal Metal Fab.
Depreciation or damage caused by normal wear and tear, lack of reasonable and proper maintenance,
failure to follow operating or installation instructions, misuse, lack of proper protection during storage, or
accidents.
e Normal maintenance costs.
Parts Replaced under Warranty Hf Coastal Metal Fab, Inc. elects to repair a defective product or component
thereof, Coastal metal Fab will, at its discretion, utilize either new or remanufactured parts or components. If
any such part or component proves to be defective within 12 months of installation or before expiration of this
warranty, whichever is later, Coastal Metal Fab, Inc. will repair or replace, as it elects, such defective part or
component.
Securing Warranty Services To obtain service under this warranty, the original retail purchaser must request
warranty service during the applicable period of warranty from a dealer authorized to sell the product being
serviced. When making such a request, the purchaser must present evidence of the product's original
purchase date, and make the product available for service at the dealer's place of business.
Limitations The selling dealer has no authority to make any representation or promise on behalf of Coastal
Metal Fab or to modify the terms or limitations of this warranty in any way. Coastal Metal Fab shall have sole
discretion to determine whether a product or component is defective. Coastal Metal Fab reserves the right to
discontinue or modify any of its products and, if Coastal Metal Fab elects to replace a defective product under
this warranty which has been discontinued or modified, it may do so with a product deemed by Coastal Metal
Fab to be of comparable quality and function.
THIS WARRANTY IS GRANTED IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR
IMPLIED INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. UNDER NO CIRCUMSTANCE SHALL COASTAL METAL FAB
BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES OF ANY NATURE RESULTING
EROM ANY DEFECT IN THE PRODUCT OR ITS COMPONENT PARTS. SOME STATES DO NOT ALLOW
LIMITATIONS ON OR EXCLUSION OF IMPLIED WARRANTIES OR INCIDENTAL AND CONSEQUENTIAL
DAMAGES SO THE ABOVE EXCLUSIONS MAY NOT APPLY TO YOU.
16
HYDRAULIC DRIVE
MOTOR CONNECTION
DIAGRAM
LINE IN
LINE OUT
Pump Volune Requirements
Conveyor Motor: 16GPM
Spinner Motor: 12 GPM
17
DownEaster-> SALT SPREADER
“oastal Metal Fab ph: 207-729-5101
120 Old Lisbon Rd. fx: 207-729-8782 Conveyor Assembly
Topsham, ME 04086
14” GAS/HYDRAULIC
le” ELECTRIC
GAS
GEARBOX
De
Dider Hyd units w/ Love joy
use Gas gearbox w/ Input shaft,
(CUT 1-5/8" OFF SHAFT)
ELECTRIC
GEAR BOX 8 - HYDRAULIC GEARBOX & MOTOR
ASSY
dwg #| Part No, Description
DownEaster Sander Parts Price List - 12 & 14" conveyor models
CONVEYOR PARTS Gas/Hyd 8 Elec 14" 8 12" 1yd and up
1 SMV509 Gearbox mounting bracket, painted steel
1 SMV509S Gearbox mounting bracket, stainless steel. =
1A ¡SMCSOS Chute stabilizer bracket, available painted only ( on older models only) a |
2 SMV529S Idler adjustment angle, stainless steel a o
3 SPGV110A |14" X8' conveyor chain, 662, gas/hyd, 12.25" center to center on sprockes — — ————
3 SPGV110 14" x S conveyor chain, 862, gas/hyd, 12.25" center to center on sprockets |
3 |SPGV110C |14" x 10' conveyor chain, 662, gas/hyd, 12.25" center to center on sprockets 0
3 ISPGVIOD Ma"x7 ” conveyor chain, 662, gas/hyd, 12.25" center to center on sprockets An
3 SPEV110A |12" x 92" conveyor chain, 662, for 8" electric sander, 10.25" center to center on sprockets >
3 SPEV110B 127 x 78" conveyor chain, 662, electric, 10.25" center to center on sprockets a
3 |SPEVMOC |12" x 43.5” conveyor chain, 662, electric, 10.25" center to center on sprockets
3 SPEV110D 12" x 24" conveyor chain, 662, electric, 10.25" center to center on sprockets TT
4 |SPV111 Conveyor Chain Single Master Link (662), includes 2 pins wi cotters, 1-5/8 pin nto pin o
5 SPGV112 Conveyor chain cross bar, 14" conveyor |
5 SPEV113 Conveyor chain crossbar, 12" conveyor ` ie
SA |SPGV114 14" Conveyor chain crossbar/link assy (2 SPV 111, SPGV112, no pins)
5A |SPEV114 12" Conveyor chain crossbar/link assy (2 SPV111, SPGV113, no pins) 0 ==
6 SPV113 Pin w/ cotter for 662 conveyor chain
7 SPGV116 14" Conveyor Driveshaft a
7 SPEV116 12” Conveyor Driveshaft, 1.125 1. 125 x 16-3/8" w/ keyway a
TA ¡SPGV115 14" driveshaft assy, (1 SPGV116, 2 SPV132, SPV118X, HWF352) a
7A |SPEV115 12” driveshaft assy (1 SPGV116, 2 SPV132, SPV118X, HWF352)
8 HWF352 Key 1/4x2™ conveyor driveshaft or clutch a
9C [SPV118C Conveyor drivefidler sprocket, 8Tx1.125 w/ keyway (1. a electric) or
90 |SPV118D Conveyor idler sprocket (1 yd+ electric), 8Tx1.125 — |
10 SPV132 Driveshaft bearing, 1.125 | A a
14 ¡SPV120 Driveshaft coupling TE
15 IHWF185 Bolt 3/8-16x2" HH (also spinner shear pin) a
16A |SPV121A Gas Gearbox - Worm Gear Reducer 20:1 output shaft 1-1/8" for 14" conveyor a
Gearbox Hydraulic - Worm gear reducer 20:1 output shaft 1-1/8 X 1.94 hydraulic adapter w/ 4 holes, 14"
16B |SPV121B conveyor
16C |SPV121C Elec Gearbox (Worm Gear Reducer 50:1 Output Shaft 1 1/8" X 14 1/2").
19 |HWF350 Key 1/4x1" Gas gearbox shaft LT =
19A |HWF352 Key 1/4x2" Elec gearbox shaft a —
20A |SPV123A Gearbox input shaft sprocket, 16T x 1, gas & gasihydraulic spreaders a
20B |SPV123B 40B-20x1 gearbox shaft sprocket, electric spreaders
21 SPV124 Gearbox shaft bearing, 1" : =
22 |SPV128 Edge guard, plastic, short Е
23 |SMV530 Idier adjustment bracket, conveyor, painted steel В
23 |SMV530S Idler adjustment bracket, conveyor, stainless steel
24 |SPGV131 14" idler shaft, 1.125 a
24 ¡SPEV131 12" idler shaft, 1.125
24A |SPGV130 14" Idler shaft assy (1 SPGV131, 2 SPV118X, SPV131, HWF352)
“ 24A SPEV130 12" Idler shaft assy (1 SPEV131, 2 SPV118X, SPV131, HWF352)
25 |SPV131 [dier shaft bearing, for 1.125" shaft LS
26 |HWF410 Nut 3/4-10 lock (jam) H
26 |HWF411 Nut 3/4-10 Lock (jam) H SS
27 |HWF285 Вой 3/4" conveyor threaded adjusting bolt,ssl, w/ 2 std nuts & one lock nut co Tees
27 |HWF286 Bolt 3/4"conveyor threaded adjusting bolt, mild steel. w/ 2 std nuts & one lock nut
28 ¡HWF408 Nut 3/4-10 H 1
28 :HWF409 Nut 3/4-10 H SS
—29 SPSLIO2 Hydraulic Motor for Spinner on 14" & 24" Spreaders & 14" Conveyor/24" w/gearbox on pass side a
30 |SPV125A 1-1/8" gearbox seal, 2-7/16" outside diameter, output shaft, gas gearbox
31 SPV126B 1" gearbox seal, 2-7/16" outside diameter, input shaft, gas gearbox a
32 [SPV127 Freeze plug, 2-3/8", for gearboxes with plugs )
19
DowmnkEaster>&- SALT SPREADER
Coastal Metal Fab ph: 207-729-5101 Chute / Spinner Assembl
120 Old Lisbon Rd. fx: 207-729-8782 Р y
|! Topsham, ME 04086
| FIXED CHUTE DETAIL
а / 12° LONG CHUTE
FLIP CHUTE DETAIL
RAIL BRACKET (42)
к. >
TE
— 44B SHORT CHUTE ASSY
— —— ВН
: LONG (418) ass (SHORT) © sos (36)
: | ax
ge : 440) 41B) ASSY (LONG)
“ a SHORT / 78" BEND
(408) = y 7e BEND Mon ND
RDAD SIDE A = \ rani (378) A
^ 0
40B
CURB SIDE
LONG
209) RETROFIT KIT
50В
HORT
RETROFIT KIT
LONG HYDRAULIC
CL
SHORT (51D) omc
ASSY
SHORT GAS 23° ELEC AFTER 7607
7 X | ASSY
ELEC 1YD UP
SHORT Gua LONG
34B ss Ч
i .
— SHORT ELEC UNDER 1YD (158
(©) ASST SHORT
от (5) ELEC UNDER 1YD PRE 7608 cm
15° ASSY a
LONG (52 Gas AFTER 7512
ASEY
ELEC 1YD UP PRE 7513 #
35° ASSY A
LONG
So SHEAR PIN
(Part no. HWF459) (Part no. HWF 455)
20
Pome re a ama
CHUTE / SPINNER PART'S Gas/Gas-Hyd Self Contained 14™ Conveyor
35 |SPN114A Chain tension adjuster, for all gas spreaders
36 |SMC500 Short chute assy, painted steel, w/ int baffles & axt flaps (14"cnvyr)
36 SMC500S Short chute assy, stainless steel, w/ int baffles & ext flaps (14"cnvyr) a
37 SMC501 Front deflector, painted (GAS)
37 |SMC501S Front deflector, stainless (GAS) i
38 |SMCS04 Metering handle, fits road side or curb side, painted steel UT .
38 SMC504S Metering handle, fits road side or curb side, stainless steel TT re etre
38A |SMC506R Metering handle cover, chute, rubber ias
388 HWC100 Metering handle collar, chute, carbon steel a OT ae
| 38B |HWC105 Metering handle collar, chute, stainless LLL
33 SMC507 Rear chute fiap w/ hinges, painted steel AAA
39 |SMC507S Rear chute flap w/ hinges, stainless steel UT AA ads
40A |SMC508 Road side chute flap w/ hinges, painted steel O a ms
40A |SMCS08S [Road side chute flap w/ hinges; stainless steel oT bee == а
408 |SMC509 Curb side chute flap wl hinges, painted steel o O DI]
408 ¡SMCSO9S Curb side chute flap w/ hinges, stainless steel | В
41 SMC510 12" long chute extension, painted steel (14" conveyor) PTT
41 SMC510S 12" long chute extension, stainless steel (14" conveyor) a
41A |SMC511 Short flip chute assy, painted w/ int baffles 8 exl flaps (14"cnvyr) Rail Bracket & Flip chute assy N
41A |SMCS5115 |Short flip chute assy, S/S, w/int baffles & ext flaps (14" cnvyr) Rail Bracket & Flip chute assy x
41B |SMC521 Long flip chute assy, painted, w/ int baffles & ext flaps (14" conveyor) SMC513A & SMCS19A as
418 |SMC521S Long flip chute assy, stainless, w/ int baffles, & ext flaps (14” cnvyr) | Cw
42 SMCS13A . |Rail bracket for flip chute, painted steel (14" cnvyr), one-piece upper chute section a
42 |SMC514AS [Rail bracket for flip chute, stainless steel (14” cnvyr), one-piece upper chute section
43 HWF419 Pin w/ cotter, stainless, for flip chute (2 pins needed per chute assy) —
44A |SMC517A Flip chute lower portion, SHORT, steel, with baffles & ext fla ps (14" cnvyr), for 1-piece rail brkt пн)
44A |SMC518AS [Flip chute lower portion, SHORT S/S w/ baffles & ext flaps (14" cavyr), for one-piece rail bracket |
44B |SMC519A % |Flip chute lower portion, LONG, steel, with baffles & ext flaps (14" cvyr), for one-piece rail brit
448 |SMC520AS Flip chute lower portion, LONG, S/S wi int baffles 8 ext flaps (14” cnvyr), for one-piece rail brkf. - |
45 |SPS103 Long Spinner Shaft - Shaft only, 35", gas/hyd & 1yd+ electric spreader A _
45A |SPS102A Short Spinner Shaft - Shaft only, 23", gas/hyd & 1yd+ electric spreader —
458 |SPS102B Short Spinner Shaft - Shaft only, 1/3 or 2/3 yd electric spreader J
| 46 |SPGS104A [Spinner disc, 14" painted. DU E
46 |SPGS104B [Spinner disc, 14" stainless a = —
46 |SPGS104C -|Polypropylene Spinner disc, 14", TT ui
47 |SPS112C Long shaft assy, hydraulic spreader, includes shaft, 1/2 lovejoy, 2 bearings Ns
— ‘Spinner bearing and pillow block, gas spreader (grease fitting on flat side), 7/8" shaft. UCPSB -205-14 SB
48° |SPS109A 718" bore zerk on bottom. 1yd_, elec, serial# greater than 7512.
48 SPS109C Spinner bearing and pillow block, gas spreader (grease fitting on flat side), 3/4" shaft
49 |SPS110 Spinner shaft sprocket, 26T x 7/8 LT
50 |HWF350 Key 1/4x1" ë a —
SOA |SMC522 Long flip chute retrofit kit, painted steel, (SMC521) and assy (SPS119)
SOA |/5MC522S Long flip chute retrofit kit, S/Song flip chute (SMC521S) and long flip shaft assy (SPS119) a
50B |SMC512 Short flip chute retrofit kit, painted steel, (1 ea SMC511, SPS116) 7
_ 508 |SMC512S [Short flip chute retrofit kit, S/S (1 ea short flip chute assy (SMC511S) & assy SPS11 6)
51A |SPS107A Short shaft assy, (gas) 23", shaft, sprocket, 2 bearings. 1yd+, elec, serial# greater than 7607
| 51B |SPS107B Short shaft assy, 1 yd +(elec) shaft, 2 sprockets, 2 bearings. 1yd+, serial# less than 7608
51C |SPS107C Short shaft assy, 1/3 or 2/3 yd (elec) shaft, 1 sprit, 2 brngs. Serial# grtr than 7607 (MEDIUM 23")
— 91D [SPS107D Short shaft assy, hydraulic spreader, includes shaft, 1/2 lovejoy, 2 bearings
__51E |SPS107E Short shaft assy, 1/3 or 2/3 (elec) shaft, 2 sprkts, 2 bearings, serial# less than 7608 (SHORT 15")
52A |SPS112A Long spinner shaft assy, 35" (gas) shaft, sprkt, 2 bearings. 1yd+,elec, serial greater than 7512 —
52B |SPS112B Long shaft assy, 1 yd + (elec) shaft, 2 sprkts, 2 brngs. 1yd+, serizl# less than 7513. (LONG 35") ВЕ
S3A |SPS117 Lower (SHORT) flip shaft assy, includes shaft & 2 bearings
53B |SPS121 Lower (LONG) flip shaft assy, includes shaft & 2 bearings
54 SPS118 Upper flip shaft assy, gas, includes shaft, collar, 2 bearings, sprocket
54A |SPS119 Long flip shaft assy, for long flip chute. (INCL SPS118,5PS121) a
54B |SPS116 [Short flip shaft assy, for short flip chute. (INCL SPSTISSPSTEN o ные
55 |SPS112 (Upper shaft collar, flip chute (short or long) В
56 |SPS113 ¡Upper shaft, flip chute (short or long), shaft only CT === co
57A ¡SPS114 ¡Lower shaft, (SHORT) flip chute, shaft only a In
57B ¡SPS120 |Lower shaft, (LONG) flip chute, shaft only с |
58 |SPN128B lLovejoy7/8" hub for spreader. LS
71 |SPN112A [79P (bottom chain) Roller chain, bagged, shaft to gearbox, all gas spreaders.
21
DownEaster-> SALÍ SPREADER
DRIVE PLATFORM DETAILS
GAS & HYDRAULIC
7
ео
СС + Briggs & Stratton
Honda
+ ASSY 5 = =
= _- © SZ Г
SEE SPINNER & CHUTE PARTS SHEET — 22
| MOTOR / DRIVE PLATFORM Gas & tHivdrauiic 14" Conveyor
59 15PN100A ¡Briggs & Stratton Model 11.5 INTEK ОНУ, 215907-0133-E1 K1030 gas engine..
59A [B & HO |B & S Starter Motor for 10.5 HP Motor O
59A [B & HO В & S Starter Motor for 9 HP 2129070114E1 a a
59A |B & HO 8 & S Starter Motor for 10.5 HP 28B7071008E1K3030 ~~ ——m—————
60 tSPN100B ENGINE-HONDA 11 HP
60A |B & HO Honda Starter Assy 11HP | ПН
60B |B & HO Honda Motor Starter Metal 11HP AA не
60C |B & HO Honda Motor Starter Plastic Shroud 11HPp eT
60D IB & HO (Recoil cord assy 11HP НЕ |
61A |SMN501A — !Engine mount, painted, Briggs O
61A |SMNS02AS ¡Engine mount, stainless, Briggs TOUT |" ен
618 |SMN501B [Engine mount, painted, Honda, pre-2004 (before SN 5405) ee
61B |SMN501C [Engine mount, painted, Honda, 2004 & later (after SN 5404) TTT
518 |/SMN5028S ¡Engine mount, stainless, Honda, pre-2004 (before SN 5408) =
— 618 SMN502CS Engine mount, stainless, Honda, 2004 8 lat: r (after SN'5404) ss
62 |SMN503 Painted Steel Chain Guard (2 piece’s) TUT Ca
62 |SPN103S ¡Stainless Steel Chain Guard (2 pieces) TITI Ш CTT ey
63 SPN104A [Electric Clutch with centrifugal friction drive, for gas spreaders. 12VDC SAA
_ 64A |SMNSOGA | Tailpipe assy, new 10.5hp Briogs 8 9hp Briggs, exhausts to roadside of engine cover
64A |SMN506D _ |Tailpipe assy, old 10.5hp Briggs, exhau 1s beneath engine platform TT
648 |SMN506B |Tailpipe assy,11hp Honda, exhausi exits on road side directly behind hopper ~~ ~~ = — ———
64C |SMN506C i Tailpipe assy, Tecumsah EE es
65 [SPN107 [Solenoid for 14" gas spreader — ma ER
66 |HWR126 [Rubber grommet, 1" I Em aaa
67 ¡HWC110 ¡Locking collar, 1", electric clutch, w/ set screws ” rss
ai 68 [SPN109 [Engine sprockel, 12T x 1", shipped with 1/4 x 1" key (pn DF-407) TT
68A |HWF350 [Key 1/4 x 1 engine shaft a - Se
69 |SPV124 |Gearbox Shaft Bearing 1" w/zirc fitting | Leese
70 [SPN111 [Clutch sprocket, 52T a
| 71 [SPN112A 5 (bottom chain) Roller chain, bagged, shaft to gearbox, all gas spreaders. — —
qi -| SPN112B |77P {Top Chain) (before 2005) Roller chain bagged, engine to clutch,( Briggs)/Tecumseh-gas
_ 75P [top chain) Roller chain, bagged, shafi-motor for lyd+ electrics before SN 7608, engine-clutch for 7
71 SPN112C (Hondas) w/ SN after 5404, Briggs after 2005 ' : :
71A |SPN113A Masterlink for roller chain a os"
— TÍA |SPN113B Offset link (half link) for roller chain i
72 |SMN518 Engine hood, painted steel o ен
72 |SMN518S |Engine hood, stainless steel II
73 |5РМ№119 Rubber hold-down, engine cover —— aa TT a ЙЕ
| 74 |SPN120 Rubber hood gasket for engine cover, SPECIFY (20.5" Elec) (30" Gas) = “ее
75 |SMN521 Engine Platform Assembly, painted steel
75 |SMN521S _ [Engine Platform Assembly, Stainless Steel a eT Te eee
85 |SPN122D |Throtile control motor, wires on side with one lug. (FOR ALL TO CURRENT) | —————
85 SPN122B Throttle control motor (old one), wires on side with two lugs ios
85 |SPN122C Throttle control motor, Warner Linear 512-17 АВ-02 NA
86 |SPN123A |Nylon Throttle control Link Briggs/Tecumseh —
87 |5ММ525 Bracket for choke indicator, stainless (HONDA or BRIGG'S) ? mu
| 88 |SPN425 |Choke indicator plunger switch |
89 |SPN1238 [Honda throttle linkage ES TE e Читы
90 |SPN122D [Throttle contr motor, 4 mtg lugs, units sold in 2005. includé bracket; specify Briggs/Honda
| pe cont motor brkt, Honda, for SPN122A {wires on side w/ 1'lug), for use with Hondas with exhaust
91 SMN524C pipe (SN before 5405) a r
FT | Throttle control motor bracket, Honda, for SPNTZ2B (wires on side wi? lugs)), for use with Hondas with
91 SMN524D exhaust pipe (SN before 5405) un :
91 SMN524F [Throttle control motor bracket, Honda, for SPN122C (Warner Linear motor) os
91 SMN524G [Throttle control molor bracket for Honda after SN 5405 (2004-present) AA Ad
92 SMN524A [Throttle control motor bracket, Briggs, fits 4 lug and 3 lug throttle control motors
93 ISPN128A ¡Lovejoy 1" hub for spreader..LOVL100X1 ias
¡Lovejoy set for spreader to include:..3 LOVL 100X3 (lovejoy, 17..2 LOVLO99/1100SOX (spider)..1 ————
93A |SPN128 LOVL100X7/8 (lovejoy, 7/8")
94 |SPN128B [Lovejoy7/8" hub for spreader. a. DU енвд
35 |SPN128C [Lovejoy spider sox for spreader. me
| Hydraulic Motor, for spinner on 24"&14" spreaders, & conveyor on 14" spreader (and 24" spreader with
96 ISPSL102 'gearbox on passenger side (50:1 gearbo ))
97 |SMN501D — |Motor mount, painted, hydraulic
97 |SMN502D [Motor mount, stainless, hydraulic eee
— 98 ISMN522 |Engine platform, painted, hydraulic CUT A e
98 ISMN5225 "Engine platform, stainless, hydrautic ~~. —
23
DownEaster — s/LT SPREADER
Feed Gate Assembly
NEW STYLE
SERIAL NO. 9297 AND UP
113
MALE (111) ©
| Дейн:
(07)
OLD STYLE
PRIOR TO SERIAL NO, 9296
ASSY SMG500
ASSY SMG500S
109
“109
109A
110
111
112
112
113
114
115
115A
115B
115C
115D
SM G501
SM G501S
SM G512S
SMG502S
SPG103A
SMG504
SMG504S
SPG110
SPG108
SM G509
SMG513AS
SMG513BS
SMG510S
SMG511S
me ве
Feed Gate
Feed gate assy, painted steel, includes gate (SMG501), tab (SMG502), gate lock knob (SPG103A),
arm (SMG504), grip (DSPG110), and hardware
Feed gate assy, stainless steel, includes gate (SMG501S), tab (SMG502S), gate lock knob
(SPG103A), arm (SM G504S), grip (SPG110), and hardware
Feed gate, painted steel I " ВЕ
Feed gate, stainless SUBG1 ees a
Feed Gate, Stainless steel NEW STYLE (serial no. 9297 and up)
Gate tab, stainless steel
Gate lock knob SPECIFY (Male for Gas) (Female for Electric)
Gate adjusting arm, painted steel
Gate adjusting arm, stainless steel
Handle grip, gate arm TUDO
Salt flap
Salt flap attachm ent plate, comes only in stainless
Feed Gate keeper left side, stainless steel
Feed Gate keeper right side, stainless steel
Feed Gate Adjusting Arm Stainless Steel
Handle lock positioner Stainless Steel |
e
DownEaster >
GAS ENGINE DRIVEN HYDRAULIC SALT SPREADER
TO VALVE BLOCK
136
SN SHEAR PIN
2A
(Part nn HWE AS5)
: 0 | GAS DRIVEN SELF CONTAINED HYDRAULIC SPREADER 1
116 ¡SPN190E J.D.Tech 5.5HP Engine |
117 |CMF Hydraulic Tank a a
118 |SPE146 Choke Solenoid | A
119 [CMF — Pump Bracket a a
120 [CMF — ump Plate Шо
121 |SPV116 ¡Drive Shaft a
122 |SPV118A Conveyor drivelidler sprocket, 6T x 1.125, with keyway (less than 1yd)
123 |SPV132 Driveshaft bearing, 1.125 TT Ey
124 |$РУ120 Shaft Coupling 1-1/8" ee
| 125 [SPH113 Hydraulic Drive Motor —— TT |
— 126 ICMF OT Valve Block Bracket E
127 |SPE140 ¡Valve Block AA оселеот неееысна НЫ
DAA NAL A ==
128 |sPEs1en Absorbed Glass Mat Battery, new style, 7.5x5x7 (LxWxD), for spreaders w/ batt tray under engine
E MT TS EEN
129 o nn
130 SE
| 130A
130B rame” [Lovejoy 5/8" w/ keyway (motor shaft)
Battery Strap
Hydraulic Spinner Motor
Mounting Bracket for Hydraulic Spinner Motor
¿lille “lo
130D [SPN130
Lovejoy 7/8" with keyway (spinner shaft)
a Pu fan spider sox
131 ISPN122A Throttle Assembly
| 132 [sPH112 — [PumpC204 I A
| 133 [SPH117 Oil Filter Lenz CPA-380-1018 NYY
| 134 |SPN130C [Love Joy 7/16" wi 3/32" key -
135 |SPN129C [Love Joy Spider
ie ISPN130A [Love Joy 3/4" wf 3/16" keyway E
137 |SPHi16 Hydraulic Mount | В
138 |SPH118 Filter Breather Assy Honda or J.D ло о
139A [HOSE ASSY [Hose 13" Valve Block to Pump | EA
1398 |HOSE AssY Hose 15" Valve Block to Filter | E —_
140A |HOSE ASSY |Hose 7" Spinner Motor to Valve Block Ca
1408 [HOSE ASSY [Hose 31-1/2" Spinner Motor to Drive Motor LOS ee
141 |HOSE ASSY [Hose 31-1/2" Vaive Block to Drive Motor Où
142 |HOSE ASSY |Hose 12" Pump to Tank Te
143
72
CMF
Block Solenoid
74
SPN120
SMN518 Engine hood, painted steel
[Rubber hood gasket for engine cover, approx 20.5" =
42
[SMC513A
[Rail bracket for flip chute, painted steel (14" cnvyr), one-piece upper chute section
27
=-=;;=--—* MESA
SMH504 Key-hole screen hinge, pair, painted steel
SMH504S Key-hole screen hinge, pair, stainless steel
=== = es
тат = ==
fn —— A тет = НН
SPH109A _ Top-screen, 2 piece,
es = ae = ES
“ |sPH109B __|Top-screen, 2 piece,
em i] ey Les DE
SPH109C Top-screen, 2 piece,
Fria р ое
SPH109D Top-screen, 2 piece,
= 7 ESS
еее == ен анны т =
SPH109F _ Top-screen, 2 piece,
SPH109G ___{Top-screen, 2 piece,
SPH110A Top-screen, 2 piece,
SMHS508CS inverted V, for 10" hopper spreader, stainless
“\SMH508DS inverted V, for 92" hopper spreader, stainless
[SMH508ES | Inverted V, for 84" hopper spreader, stainless steel (V is 60")
SMHS508FS | inverted V, for 78" hopper spreader, stainless steel {
i ee = 8
for 50.5x92 flat-top spreader, Dx-150Be, (
for 64.5x92 flat-top spreader, Dx-2508e, (pcs are 61x 43.5)
for 42.5x92 flat-top spreader, Dx-1008e, (pcs are 39x 43.5)
SPH109E Top-screen, 2 piece,
——————_+ ————]—]———
for 50x78 flat-top spreader, Dx-1206e, (pcs are 47x 36.5)
me a mm на
SMH5088S Inverted Y, for 9" hopper spreader, stainless steel (V is 7')
steel (Vis 8’)
steel (Vis 68")
[- |sMH505 Light mounts, pair, painted steel ___-
SMH5055 Light mounts, pair, stainless steel
SMH506 6” painted hopper extension, 50.5x96", converts 1.9 yd to 2.5
SMH506S 6" stainless hopper extension, 50.5x86", converts 1.9 yd to 2.5
SMHSOSA Inverted V, for 8' hopper spreader, painted steel (V is 6’)
SMH508B | Inverted V, for 9' hopper spreader, painted steel (Vis 7’) a
SMH508C [Inverted V, for 10° hopper spreader, painted steel (V is 8')
т SMH508D inverted V, for 10° hopper spreader, painted steel (Vis 8") a
SMH508E inverted V, for 84" hopper spreader, painted steel (Vis 60")
SMHS08F Inverted М, for 78" hopper spreader, painted steel (Vis 549
SMHSOSBAS _|Inverte V, for 8' hopper spreader, stainless steel {V is 6°) a
for 50.5x96 flat-top spreader, eg Dx-1908, (pcs are 47x 45.5)
V is 54")
неее — ==
pcs are 47x 43.5)
for 50 5x84 flat-lop spreader, Dx-1607, (p
for 50.5x108 flat-top spreader, Dx-2109, (
for 71.5%96 pitched-top, eg Dx-3308 & Dx-4008
SPH110B Top-screen, 2 piece, for 59.5x108 pitched-top, Dx-3309
cs are 47x 39.5)
pes are 47x 51.5)
SPH110C Top-screen, 2 piece,
for 71.5x108 pitched-top, eg Dx-3709 á Dx-4509
SPH110D Top-screen, 2 piece,
SPH110E Top-screen, 2 piece,
SPH117A - Top-screen, 1 piece,
for 59.5x120 pitched-top, Dx-3310
for 71 5x120 pitched-top, eg Dx-4010, Dx-5010, Dx-6010
for 42.5x43.5 flat-top, Dx-0604e
1SPH111B° _ |Top-sereen, 1 piece,
SPH111C Top-screen, 1 piece,
[SMH512. Screen clamp, each
for 42.5x74 flat-top, Dx-0302e
ENE VAN ST ETRE dln
for 34.5x43.5 flat-top, Dx-0304e
SPH111D Top-screen, 1 piece, for 50.5x96 flat-top, old style, eg Dx-1908
| | Accessories
|
ISPA100 Tie-down kit, up to 2.5 yds, includes 4 S000# straps w/ 5000# ratchets os
SPA101 Tie-down kit, DX-0302e, 2 ratchet straps and hitch mount a ie
SPA102 Tie-down kit, 3-6 yds, includes 4 10,000# straps w/ 10,000# ratchets Ш FA
o Mini strobe light | Smee
SPA104A Tarp cover for 1.9 or 2.5 yd gas/hydraulic spreader, 51x96 a TES
|. [SPA104B Tarp cover for 1/3 yd, 4° hopper electric spreader (Dx-0304e), green, 36x44, wihlogg 71
SPA104C |Tarp cover for Baby electric spreader, green, 42x24 | ser
— sra Tarp cover for 2/3 yd, 4' hopper electric spreader (Dx-0604e), green, 43.75x44 with Logo me
SPA104E Tarp cover for 1 yard electric spreader, green, 43x96 I О LT
¡SMASOGA Remote grease fitting kit, 9" grease tube, for hoppers up to 10' a
НЕ SMA506B [Remote grease fitting kit, 14' grease tube, for hoppers up to 111-15" —— |
SMA507 — Fenders, pair, painted steel (single axle)
SMA507S Fenders, pair, Stainless steel (single axle)
г ; SMA508 Fenders, pair, painted steel (tandem axle) a a В
Fenders, pair, stainless steel (tandem axle)
SPA1O9 Mud-flap, pair
____ |smas10 [бак lock, ptd steel, up to 102", 2x3x3/16 tubing wi T° dia x 4 shaft om sede Ferrer
SMA511 Ladder, painted steel, hinged, with 10" offset from spreader Le EE
_|SMAS11s— Ladder, stainless steel, hinged, with 10" offset from spreader — ==
SMAS12A [Cab shield. painted steel, fits 50.5" wide hopper. (DP-1908 width end plate) = _
SMAS12B [Cab shield, painted steel, fits 59.5wide hopper, (DP-3009 width end plate) ~~ — Ss
SMASTZC— [Cab hiel oo fits 71.5"wide hopper, (DP-3308 width end plate) Ш ms
SMAS13AS Cab shield, stainless steel, its 50.5" wide hopper, (DS-1908 width enex —— ——
SMAS13BS _ (Cab shield, stainless steel, fits 59.5" wide hopper, (08-3008 width end vite" ———— _—_
|SMA513CS Cab shield, stainless steel, fits 71.5" wide hopper, (DS-3308 width end plate) =
SMAS14A Spill shields, pair (frontérear), painted steel, fits 50.5" wide hopper, (DP-1908 width end plate)
SMA514B Spill shields, pair (front&rear), painted steel, fits 59.5" wide hopper, (DP-3009 width end plate
с SMAS14C Spill shields, pair, (front&rear), painted steel, fits 71.5" wide hopper, (DP-3308 width end plate)
SMAS1SAS [Spill shields, pair (ftont & rear), S/S, fits 50.5" wide hopper, (DS-1908 width end plate). |
SMAS515BS Spill shields, pair (front & rear), S/S, fits 59.5" wide hopper, (DS-3009 widthend plate, —
SMAS15CS Spill shields, pair (front & rear), 8/5 fits 71 5" ide hopper, (DS-3308 width end plate). —
|Adapter kit for tailgate spreader — AA E nas EA
aint, db dove gray - sold as 1 quart paint with separate hardener miras nosdog — nn
Paint, at, hiway orange - sold as 1 quart paint with separate hardener, mix as nodos” ——————
N ye, spray can 7 + Mameeded __ TS
Paint, can, hiway orange, Spray can
28
< 00)
">