WOLFVISION Cynap Core Pro Advanced Collaboration and Presentation User Guide

WolfVision GmbH
Oberes Ried 14
A-6833 Klaus / AUSTRIA
1
Tel. +43-5523-52250
Fax +43-5523-52249
E-Mail: [email protected]
www.wolfvision.com
WolfVision GmbH
Oberes Ried 14
A-6833 Klaus / AUSTRIA
Tel. +43-5523-52250
Fax +43-5523-52249
E-Mail: [email protected]
www.wolfvision.com
vSolution Cynap Core PRO
Network Integration
1.
Basics .......................................................................................................................... 3
2.
Glossary ....................................................................................................................... 3
2.1.
LAN / Ethernet settings ............................................................................................ 3
2.2.
WLAN settings – access point ................................................................................. 4
2.3.
WLAN settings – infrastructure (Cynap Core PRO acts as client) ............................ 5
2.4.
Date and time .......................................................................................................... 6
2.5.
Host name ............................................................................................................... 6
2.6.
LAN / WLAN port ..................................................................................................... 6
2.7.
FTP Client settings .................................................................................................. 8
2.8.
Proxy settings .......................................................................................................... 8
2.9.
Security ................................................................................................................... 8
3.
Network integration (examples) ...................................................................................10
3.1.
Stand-alone access point mode (without network integration).................................10
3.2.
Cynap Core PRO wireless network access point mode ..........................................11
3.3.
Cynap Core PRO network infrastructure mode .......................................................12
3.4.
Cynap Core PRO connection to a Visualizer...........................................................13
4.
Firewall rules ...............................................................................................................15
5.
Differences in Open Mode / Protected Mode ...............................................................20
6.
BYOD ..........................................................................................................................21
7.
Document and media player ........................................................................................22
8.
Network Stream (input)................................................................................................23
9.
Control of Peripheral Devices ......................................................................................25
10.
Cloud services.............................................................................................................26
11.
Network Drive..............................................................................................................26
12.
User interface ..............................................................................................................26
13.
Hardware and OS........................................................................................................27
14.
Administration .............................................................................................................27
15.
Bandwidth Measurement Data ....................................................................................28
15.1.
PowerPoint Presentation ........................................................................................28
15.2.
Multimedia from Notebook to Cynap Core PRO using vCast Software ...................28
16.
Client System Requirements .......................................................................................29
17.
Index ...........................................................................................................................30
2
WolfVision GmbH
Oberes Ried 14
A-6833 Klaus / AUSTRIA
Tel. +43-5523-52250
Fax +43-5523-52249
E-Mail: [email protected]
www.wolfvision.com
1. Basics
Before starting, check the existing infrastructure and define the required equipment and
settings.
Various examples in this document show the different ways in which Cynap Core PRO can
be integrated into the network.
When connecting Cynap Core PRO to LAN and WLAN at the same time, please use different
IP ranges in order to prevent address conflicts.
The listed IP addresses are only examples.
Cynap Core PRO can be treated as a standard network device and it is as secure as the
supporting network. Cynap Core PRO cannot be considered as a router, switch or firewall.
Communication to other networks and access must to be controlled using your existing
equipment (firewall, router, switch and so on).
By default, Cynap Core PRO´s second LAN port (LAN 2) is dedicated to fully integrate a
WolfVision Visualizer. The behaviour of this LAN port (LAN 2) can be changed to connect
Cynap Core PRO e.g. to a RMS network (Room Management System) and mirroring
purposes. This way, the built-in DHCP server is de-activated and a Visualizer cannot be fully
integrated. When using vSolution Matrix, it is recommended to connect all station of a room
to one single network switch to obtain maximum performance.
Attention:
When the second LAN port (LAN 2) is set to Visualizer Mode, never connect this LAN port for
the Visualizer to your existing network infrastructure!
If this port is set to Visualizer mode, Cynap Core PRO acts as DHCP-server on this port and
this could cause conflicts with the existing infrastructure.
When using vSolution Matrix, LAN 1 has to be used to connect all stations together.
2. Glossary
This glossary will assist you in setting up the network correctly. Please note that in order to
connect Cynap Core PRO to an existing company network, some information from the local
administrator is required.
2.1. LAN / Ethernet settings
The following settings are available for LAN 1 and also for LAN 2, when the interface mode is
changed to LAN.
Priority Interface Access
DHCP
IP address
Subnet mask
Gateway
The higher prioritized interface (value = 1) will be used for
network service first. Ensure that the value is different from
the WLAN interface priority.
Cynap Core PRO will get all network settings automatically
from the DHCP server in the existing network. Switch it to
OFF to set the static addresses manually.
Unique address in the network, i.e. 192.168.0.100. The IP
address of Cynap Core PRO can for example be set to
192.168.0.1.
Available IP addresses can be limited. A commonly used
subnet mask would be 255.255.255.0
Defines the IP address of the server / connection to other
networks (such as the internet). When Cynap Core PRO is
directly connected only to a PC, then enter the IP address of
the PC.
3
WolfVision GmbH
Oberes Ried 14
A-6833 Klaus / AUSTRIA
Name server 1 / 2
Identity
Anonymous Identity
Authentication Method
Root Certificate
Tel. +43-5523-52250
Fax +43-5523-52249
E-Mail: [email protected]
www.wolfvision.com
Input the IP address of the preferred Domain Name System
(DNS). This Server translates domain names into
corresponding IP addresses.
Login credentials to connect Cynap Core PRO in a protected
network. (802.1x).
The identity to be used on an unencrypted session before
Identity is being validated on an encrypted session.
Supported are PEAP with MSCHAPv2 and TTLS-PAP
Only root certificates are supported, load the certificate by
using the Web Interface through the WLAN interface.
Allowed certificates:
•
root certificate (CA) with common file extension .crt
Base-64-coded X.509 encoded DER certificate
•
Privacy Enhanced Mail with common file
extension .perm
Base-64-coded X.509 encoded DER certificate
certificate stored between 2 tags: “---Begin Certificate---“and”
------End Certificate-----“
2.2. WLAN settings – access point
Mode OFF
Mode Access Point
Channel
SSID Auto
SSID Manual
IP address
Subnet mask
Encryption
Transmit Power
Disable access point.
Enable access point.
Defines the channel used for wireless communication. For
optimum performance, select a currently unused channel.
If activated, an automatic SSID is generated using the Cynap
Core PRO serial number
Defines the network name in plain text for easy identification of
the WLAN network.
Following characters are supported:
- AaBbCcDdEeFfGgHhIiJjKkLlMmNnOoPpQqRrSsTtUuV
vWwXxYyZz
- 0123456789
- _-:$& ()
Defines the IP address of the access point. Cynap Core PRO
acts as a DHCP server and provides the necessary network
settings to the connected devices.
Available IP addresses can be limited. A commonly used
subnet mask would be 255.255.255.0
Defines encryption for safe network traffic. All connected
devices must use the same algorithm (WPA2).
Select the desired transmission power to optimize the range.
The maximum power depends on selected channel and region.
Hint:
Cynap Core PRO does not act as router or gateway and only serves up a “Cynap Core PRO
closed” network that will not connect to the internet even if the LAN port is connected to the
internet.
4
WolfVision GmbH
Oberes Ried 14
A-6833 Klaus / AUSTRIA
Tel. +43-5523-52250
Fax +43-5523-52249
E-Mail: [email protected]
www.wolfvision.com
2.3. WLAN settings – infrastructure (Cynap Core PRO acts as client)
Mode Infrastructure
Band
Priority Interface Access
BSSID On / Off
SSID
BSSID
Subnet mask
Gateway IP
Name server 1 / 2
Encryption
Identity
Anonymous Identity
Authentication Method
Root Certificate
Enable Infrastructure, Cynap Core PRO can be connected ac
client to an existing access point.
By default, Cynap Core PRO uses the 2.4GHz and 5 GHz
frequency band. The used frequency band can be limited to
either 2.4GHz or 5 GHz. This setting is available in SSID mode
only.
The higher prioritized interface (value = 1) will be used for
network service first. Ensure that the value is different from the
LAN interface priority.
Toggles between SSID and BSSID mode.
With BSSID (Basic Service Set Identification), the used access
point will be fixed and Cynap Core PRO will connect to the
defined access point only. Access point hopping, which is
available in SSID mode (Service Set Identification), will be
prevented.
Defines the network name in plain text for easy identification of
the WLAN network. Check existing WLAN infrastructure to get
SSID.
Following characters are supported:
- AaBbCcDdEeFfGgHhIiJjKkLlMmNnOoPpQqRrSsTtUuV
vWwXxYyZz
- ÄäÖöÜü
- 0123456789
- _-:$& ()
Defines the network name in plain text for easy identification of
the WLAN network. Check existing WLAN infrastructure to get
SSID. This setting is available in SSID mode only.
Available IP addresses can be limited. A commonly used subnet
mask would be 255.255.255.0
Defines the IP address of the server / connection to other
networks (such as the internet). When Cynap Core PRO is
directly connected only to a PC, then enter the IP address of the
PC.
Input the IP address of the preferred Domain Name System
(DNS). This Server translates domain names into corresponding
IP addresses.
Defines encryption for safe network traffic. All connected units
must use the same algorithm (None, WEP, WPA2, WPA2
Enterprise).
Login credentials to connect Cynap Core PRO in a WPA
Enterprise protected network.
The identity to be used on an unencrypted session before
Identity is being validated on an encrypted session.
Supported are PEAP with MSCHAPv2 and TTLS-PAP
Only root certificates are supported, load the certificate by using
the Web Interface through the LAN interface.
Allowed certificates:
•
root certificate (CA) with common file extension .crt
Base-64-coded X.509 encoded DER certificate
5
WolfVision GmbH
Oberes Ried 14
A-6833 Klaus / AUSTRIA
Tel. +43-5523-52250
Fax +43-5523-52249
E-Mail: [email protected]
www.wolfvision.com
•
Privacy Enhanced Mail with common file
extension .perm
Base-64-coded X.509 encoded DER certificate
certificate stored between 2 tags: “---Begin Certificate---“and” -----End Certificate-----“
Signal Level Limit (dBm)
Signal Level
Reconnect Counter
(Connection Loss)
Reconnect Counter (Low
Signal Level)
Defines when Cynap Core PRO start to search for another
access point with the same SSID in your infrastructure (WLAN
roaming). Monitoring the current signal level to prevent too low
values. Lookups could interrupt the network connection shortly
and every lookup will be counted (Reconnect Counter (Low
Signal Level).
Shows the current strength of the WLAN signal in dBm.
Counts every connection loss, e.g. when the selected access
point would be powered down.
Counts every lookup then the measured signal falls below the
user defined signal level limit.
2.4. Date and time
Time source
Cynap Core PRO has a built-in battery-buffered RTC clock
(Real Time Clock). Settings will only be lost if the battery is
empty. To eliminate the risk of incorrect time stamps, Cynap
Core PRO can be synchronized to an external time server.
Select external and input a valid IP address or URL of a NTP
time server.
2.5. Host name
Host name
The Host name can be changed in the settings under general
settings. The host name can be useful for network
administrators to see the device name in plain text in the list of
clients. Please note, this host name is not automatically listed
in the DNS list, and therefore cannot be used in a browser
without DNS registration.
2.6. LAN / WLAN port
The LAN port enables integration of Cynap Core PRO into an internal network.
Administrators of a large number of Cynap Core PRO systems can use the LAN port to
control, support and update all of their units from their local desktop PC.
The list of applications for the Cynap Core PRO LAN port is constantly increasing. It can be
used for controlling, capturing still images, viewing live video streams, firmware updates,
adjustments, menu settings and for maintenance purposes. Some features are only
supported when using vSolution Link software.
The following protocols are supported: TCP/IP, IGMP, RTP, RTSP, UDP and ARP.
Supported (tested) internet browsers are: Microsoft Edge, Firefox, Chrome, and Safari.
By default, DHCP is activated to receive all network settings automatically from the server.
Hint - WLAN:
6
WolfVision GmbH
Oberes Ried 14
A-6833 Klaus / AUSTRIA
Tel. +43-5523-52250
Fax +43-5523-52249
E-Mail: [email protected]
www.wolfvision.com
To ensure optimal performance of supplied remote control (optional), prevent channel 13 in
the band of 2.4 GHz. Switch Cynap Core PRO to standby closes all connections.
7
WolfVision GmbH
Oberes Ried 14
A-6833 Klaus / AUSTRIA
Tel. +43-5523-52250
Fax +43-5523-52249
E-Mail: [email protected]
www.wolfvision.com
2.7. FTP Client settings
FTP enable
URL
Username
Password
Test it now
Enable or disable FTP client functionality to backup and share
recorded videos and snapshots. Additional features such as
active/passive mode or secure layers (eg. Kerberos etc.) are
not supported.
Address of your FTP server in your network, like
192.168.0.100. (up to 256 characters, no space between the
characters)
Input the username according your FTP server settings.
Input the password according your FTP server settings.
During the test, Cynap Core PRO will upload a text file onto
the FTP-server (“Cynap Core PRO.txt” without content)
2.8. Proxy settings
To increase security level, use a proxy server to control HTTP and HTTPS traffic from Cynap
Core PRO. Built-in access point and other local services are not controlled. To take effect the
new settings, Cynap Core PRO will reboot automatically.
Proxy enable
URL
Host Port
Authentication
Username
Password
Enable / disable proxy service
When enable, all HTTP and HTTPS traffic will be routed to the
your proxy server. Please note, using a Proxy server may
block Skype for Business (optional) functionality.
URL of the proxy server in your network, like 104.236.10.17
(or DNS name up to 256 characters, no space between the
characters). DNS server not required, when using IP
addresses.
Port, set the used network port to connect to your proxy
server.
Disable / enable Authentication
When enabled, valid user name and password has to be
entered.
Username, given by your server.
Password, given by your server.
2.9. Security
Admin password
Defines the necessary password for administrator access. This login data is needed to
change the Ethernet Mode, and an existing administrator password.
Using the login data, an administrator can connect to Cynap Core PRO
at any time. The default password is “Password”. Remember to make a
note of any changed passwords!
Login Security
Accessing Cynap Core PRO can be protected by authentication (admin, moderator or PIN).
To prevent unauthorized access of the settings, the admin password needs to be entered
once per session.
Network Security
8
WolfVision GmbH
Oberes Ried 14
A-6833 Klaus / AUSTRIA
Tel. +43-5523-52250
Fax +43-5523-52249
E-Mail: [email protected]
www.wolfvision.com
Accessing Cynap Core PRO can be limited to secure connections only (https). Please note,
the accessing application needs to support SSL / TLS (e.g. the most modern browsers are
supporting HTML5 and SSL /TLS).
Wolfvision support access can be prohibited by disabling SSH.
LAN Security
When using wired network, use authentication (according 802.1x) to maximize security.
When using certificates, load it busy using the Web Interface.
WLAN (WiFi) Security
When using wireless network, use encryption to maximize security.
Cynap Core PRO complies with following standards:
• WEP
• WPA2
• WPA2 Enterprise (according 802.1x)
Hint
WEP allows password with a length of 13 characters.
WPA2 allows password with a length of 8 ~ 63 characters.
Use special characters carefully, not every third party device can handle it.
When using WPA2 Enterprise, load the certificate by using the Web Interface.
9
WolfVision GmbH
Oberes Ried 14
A-6833 Klaus / AUSTRIA
Tel. +43-5523-52250
Fax +43-5523-52249
E-Mail: [email protected]
www.wolfvision.com
3. Network integration (examples)
The following examples of network integration show the different ways in which Cynap Core
PRO can be integrated. Various operating systems can each connect to Cynap Core PRO to
transfer different information from different sources onto a large monitor.
3.1. Stand-alone access point mode (without network integration)
Cynap Core PRO is operated in stand-alone access point mode.
The network settings must be set manually on Cynap Core PRO (no DHCP server is
available). Cynap Core PRO generates an independent WLAN, and WLAN enabled devices
(BYOD) can connect to Cynap Core PRO.
Advantages:
- No complex network infrastructure necessary
- Cynap Core PRO generates its own stand-alone access point
- No connection to internal IT infrastructure
- Security issues - no other unit from the internal IT infrastructure can access Cynap
Core PRO
Disadvantages:
- No devices have internet access
- Cloud services cannot be used
Required settings:
DHCP
Switch to OFF to enable manual setting of addresses
IP Address
Unique address in the network, like 192.168.0.100. The IP address of a
connected PC could be set to 192.168.0.1 for maintenance purposes
Subnet Mask
Available IP addresses can be limited. A commonly used subnet mask
would be 255.255.255.0
Gateway
Enter the IP address of a directly connected PC for maintenance
purposes
Name server
Not needed
10
WolfVision GmbH
Oberes Ried 14
A-6833 Klaus / AUSTRIA
Tel. +43-5523-52250
Fax +43-5523-52249
E-Mail: [email protected]
www.wolfvision.com
3.2. Cynap Core PRO wireless network access point mode
Cynap Core PRO is integrated via a cable connection into an existing network, and is
operated in wireless network access point mode. LAN settings for Cynap Core PRO can be
provided by the DHCP server. Cynap Core PRO generates an independent WLAN, and
WLAN enabled devices (BYOD) can connect to Cynap Core PRO.
Advantages:
- All devices can communicate with each other
- Cynap Core PRO has access to the Internet and cloud services can be activated
- Cynap Core PRO can access the internet to check for firmware updates without using
additional devices
Disadvantages:
- Performance issues (all traffic is on the same network)
Hint:
If the units are in different subnets, Cynap Core PRO might not be able to be discovered
automatically by vSolution applications.
11
WolfVision GmbH
Oberes Ried 14
A-6833 Klaus / AUSTRIA
Tel. +43-5523-52250
Fax +43-5523-52249
E-Mail: [email protected]
www.wolfvision.com
3.3. Cynap Core PRO network infrastructure mode
Cynap Core PRO is integrated via a cable connection into an existing network (e.g.
Corporate network), and is operated in network infrastructure mode. LAN settings for Cynap
Core PRO can be provided by the DHCP server. In infrastructure mode, Cynap Core PRO is
connected to an existing wireless access point in the existing network (e.g. Guest network).
BYOD devices in the Corporate network and in the Guest network can connect to Cynap
Core PRO.
Advantages:
- All devices can communicate with each other
- Cynap Core PRO has access to the internet and cloud services can be activated
- Cynap Core PRO can be moved within the range of the access point
- Cynap Core PRO can access the internet to check for firmware updates without using
additional devices
Disadvantage:
- Performance issues (all traffic is on the same network)
Hint:
If the units are in different subnets, Cynap Core PRO might not be able to be discovered
automatically by vSolution applications.
12
WolfVision GmbH
Oberes Ried 14
A-6833 Klaus / AUSTRIA
Tel. +43-5523-52250
Fax +43-5523-52249
E-Mail: [email protected]
www.wolfvision.com
Cynap Core PRO can also be installed in a VLAN.
3.4. Cynap Core PRO connection to a Visualizer
Cynap Core PRO has a dedicated LAN port for connecting to a Visualizer with built-in DHCP
server functionality. Activate on the Visualizer to obtain all necessary network settings from
Cynap Core PRO automatically. Communication between Visualizer and Cynap Core PRO is
over the Wolfprot protocol. The connection between Cynap Core PRO and the Visualizer is a
direct connection (point to point) and shouldn’t be made through a switch or similar device.
More information on this protocol can be found on our website in the support section
www.wolfvision.com.
13
WolfVision GmbH
Oberes Ried 14
A-6833 Klaus / AUSTRIA
Tel. +43-5523-52250
Fax +43-5523-52249
E-Mail: [email protected]
www.wolfvision.com
Attention:
When the second LAN port is set to Visualizer Mode, never connect this LAN port for the
Visualizer to your existing network infrastructure!
If this port is set to Visualizer mode, Cynap Core PRO acts as DHCP-server on this port and
this could cause conflicts with the existing infrastructure.
Hint:
- Connect the Visualizer straight to the dedicated port. Do not add switchers, hubs,
routers or similar between Cynap Core PRO and the Visualizer to prevent error
sources.
- Cynap Core PRO can be controlled with the keys of the Visualizer. The functions of
keys from the camera head are dedicated to control Cynap Core PRO. These keys
are note have no effect to the Visualizer anymore. The IR-remote control of the
Visualizer is not effective in this setup.
- Visualizer can be controlled with Cynap Core PRO.
- Cynap Core PRO and Wolfvision Visualizer are supporting cable runs up to 100m
according Ethernet specification.
- The behaviour of this LAN port can be changed to connect Cynap Core PRO to a
dedicated RMS network (Room Management System). This way the built-in DHCPserver is de-activated and a Visualizer cannot be fully integrated.
- Be sure USB input type is not defined as “Visualizer”
14
WolfVision GmbH
Oberes Ried 14
A-6833 Klaus / AUSTRIA
Tel. +43-5523-52250
Fax +43-5523-52249
E-Mail: [email protected]
www.wolfvision.com
4. Firewall rules
Cynap Core PRO has firewall rules that must be adhered to in order to allow successful
network communications, and the corresponding services to be used. To use services with
user defined addresses and ports, be sure these are not blocked by your firewall.
Function /
Application
Inbound /
Outbound
Description
TCP / UDP
UDP
TCP
TCP
TCP
Inbound /
Outbound
Inbound
Inbound
Inbound
Inbound
Inbound
Multicast DNS (mDNS
224.0.0.251) Bonjour
Audio for Airplay
Audio for Airplay
Primary Airplay communication
Airplay video communication
Airplay audio communication
4100
4101
5000
TCP / UDP
UDP
TCP
Inbound
Inbound
Inbound
7000
7100
47000
TCP
TCP
TCP
Inbound
Inbound
Inbound
Audio for Airplay
Audio for Airplay
AirPlay communication with legacy
devices
Primary Airplay communication
Airplay video communication
Airplay audio communication
5353
UDP
1900
4100 –
4164
8008
UDP
TCP / UDP
Inbound /
Outbound
Inbound
Inbound
Multicast DNS (mDNS
224.0.0.251)
Chromecast discovery
Audio for Chromecast
TCP
Inbound
8009
32768 –
61000
TCP
UDP
Inbound
Inbound
/Outbound
Primary Chromecast
communication
Communication Chromecast
Chromecast (video data stream)
5353
UDP
Inbound
67 / 68
UDP
Inbound
UDP
Inbound
RTSP Control
19000 –
19007
19010 –
19017
7236
TCP
Outbound
MS-MICE Control
7250
TCP
Inbound /
Outbound
Touchback
50000
TCP
Outbound
Hardware cursor
extension
19020 –
19027
UDP
Inbound
Airplay
Multicast DNS
(mDNS)
Audio
Audio
Airplay
Video
Audio
Airplay Bluetooth
Audio
Audio
AirPlay
Airplay
Video
Audio
Chromecast
Multicast DNS
(mDNS)
Discovery
Audio
Chromecast
Chromecast
Video data stream
Miracast MS-MICE
Multicast DNS
(mDNS)
DHCP
RTP Stream
Port
Type
5353
UDP
4100
4101
7000
7100
47000
15
Multicast DNS (mDNS
224.0.0.251)
DHCP communication between
device and receiver
RTP media traffic port for delivering
audio and video
RTSP control port is used to
establish and manage session
Control port on which Cynap family
system listen for Miracast packets
when over existing network mode
is enabled
This port is for touchback to send
mouse events back between
Cynap to the Windows computer. If
this port is blocked, bi-directional
inputs is not possible.
Hardware cursor to reduce latency
when using touchback.
WolfVision GmbH
Oberes Ried 14
A-6833 Klaus / AUSTRIA
Wake On LAN
19030 –
19037
7/9
UDP
FTP
SSH
http, Cynap control
21
22
80
https, SSL, e.g.
Cloud Service,
Cynap control
Tel. +43-5523-52250
Fax +43-5523-52249
E-Mail: [email protected]
www.wolfvision.com
TCP
TCP
TCP
Inbound /
Outbound
Outbound
Inbound
Inbound
Usually port 7 is used for sending
the magic packet
Connection to FTP server
Access for Wolfvision support
This port used to connect to Cynap
web interface (httpd). If this port is
blocked, no connection can be
made.
443
TCP / UDP
Inbound
Proxy
8080
TCP / UDP
Outbound
NFS
CIFS
NTP
111 / 2049
137 / 139
123
TCP / UDP
TCP / UDP
UDP
Outbound
Outbound
Outbound
LDAP
LDAPS
Streaming
Multicast / Unicast
Streaming RTSP
389
636
8800 –
9000
554
TCP / UDP
TCP / UDP
UDP
Outbound
Outbound
Inbound
TCP
Inbound
PJLink
4352
TCP
Outbound
This port is used to cloud service
and for secure connect to Cynap
web for secure connect to Cynap
web interface. If this port is
blocked, no connection can be
made.
Default port proxy function (This
port can be changed in the Proxy
settings).
Connection to network drives
Connection to network drives
For optional clock synchronization
by a time server (Network Time
Protocol, NTP)
Connection to LDAP server
Connection to LDAPS server (TLS)
Used for Multicast / Unicast / Audio
/ Video Streaming
This is the communication port for
the RTSP stream. This used UDP
port will be handled automatically
This is the default port for PJLink
and cab be changed in the settings
(Peripheral Control)
vSolution Cast
Discovery Multicast
50000
UDP
Inbound
Device Discovery
50913
UDP
Inbound
For control purposes
50915
TCP
Inbound
TLS Control
50917
TCP
Inbound
16
This port is used for device
discovery all available Cynap and
Visualizer in the network by
vSolution applications (uses
Multicast IP address
239.255.255.250). If this port is
blocked, vSolution applications
may not be able to find devices
automatically.
This port is used for device
discovery
This port is used for control
purposes e.g. room control system,
and others). If this port is blocked,
no control is possible
This port is for secure
communication between
WolfVision applications (e.g.
vSolution App) to Cynap and / or
Visualizer. If this port is blocked,
secure communication to Cynap
WolfVision GmbH
Oberes Ried 14
A-6833 Klaus / AUSTRIA
Video streams
50921
TCP
Inbound
Touchback
50922
TCP
Outbound
vSolution App iOS /
Android / Windows
Discovery Multicast
50000
UDP
Inbound
http, Cynap control
80
TCP
Inbound
https, SSL, e.g.
Cloud Service,
Cynap control
443
TCP
Inbound
Device Discovery
50913
UDP
Inbound
For control purposes
50915
UDP
Inbound
TLS Control
50917
TCP
Inbound
Video streams
50921
TCP
Inbound
Touchback
(Windows, macOS)
50922
TCP
Outbound
17
Tel. +43-5523-52250
Fax +43-5523-52249
E-Mail: [email protected]
www.wolfvision.com
and / or Visualizer, inclusive
firmware updates are blocked.
Video streams between Wolfvision
App to Cynap and Visualizer. If this
port is blocked, no stream are
possible.
This port is for touchback between
Cynap and Wolfvision App
vSolution Cast to send mouse
events back to the Windows
computer. If this port is blocked, bidirectional inputs is not possible
This port is used for device
discovery all available Cynap and
Visualizer in the network by
vSolution applications (uses
Multicast IP address
239.255.255.250). If this port is
blocked, vSolution applications
may not be able to find devices
automatically.
This port is used to connect to the
Cynap web interface (httpd). If this
port is blocked, no connection can
be made.
This port is used to cloud services
and for secure connect to the
Cynap web for secure connect to
the Cynap web interface. If this port
is blocked, no connection can be
made.
This port is used for device
discovery.
This port is used for device
discovery.
This port is for secure
communication between
WolfVision applications (e.g.
vSolution App) to Cynap and / or
Visualizer. If this port is blocked,
secure communication to Cynap
and / or Visualizer, inclusive
firmware updates are blocked
Video streams between WolfVision
App to Cynap and Visualizer. If this
port is blocked, no streams are
possible.
This port is for touchback between
Cynap and WolfVision App
vSolution Cast to send mouse
events back to the Windows
computer or MacBook. If this port is
blocked, bi-directional inputs are
not possible.
WolfVision GmbH
Oberes Ried 14
A-6833 Klaus / AUSTRIA
Video data stream
Tel. +43-5523-52250
Fax +43-5523-52249
E-Mail: [email protected]
www.wolfvision.com
UDP
Inbound
/Outbound
Video data stream (e.g., BYOM,
Chromecast)
TCP / UDP
Outbound
Communication Port
WebRTC (Pexip)
32768
61000
10000 –
16000
50000 65000
1720
TCP
Outbound
TLS Control
50917
TCP
Inbound
WebSocket
7681
TCP
Inbound
WebSocket
7682
TCP
Inbound
This port used WebRTC services
like Pexip
This port is for secure
communication between Wolfvision
application (e.g. vSoltuion Link) t
Cynap and / or Visualizer. If this
port is blocked, secure
communication to Cynap and / or
Visualizer, inclusive firmware
updates are blocked.
User interface communication with
Cynap (via browser)
User interface communication with
Cynap (via fully integrated
Visualizer)
vSolution Link Pro
Wake On LAN
7/9
UDP
DNS
53
TCP / UDP
Inbound /
Outbound
Inbound /
Outbound
http, Cynap control
80
TCP
Inbound
https, SSL, e.g.
Cloud Service,
Cynap control
443
TCP
Inbound
SMTP
587
SMTP
Outbound
Discovery Multicast
50000
UDP
Inbound
Device Discovery
50913
UDP
Inbound
For control purposes
50915
TCP
Inbound
Zoom
http
80
TCP
Outbound
443
8801
TCP
TCP
Outbound
Outbound
WebRTC
http over TLS / SSL
18
Wake On LAN – Usually port 7 is
used for sending the magic packet
DNS – This port will be used for
Domain Name System. If this port
is blocked, DNS service are not
available
This is the default port to connect
to the web interface (httpd) of
vSolution Link Pro. Of this port is
blocked, connection cannot be
established
This is the default port to connect
to web interface (https) of vSolution
Link Pro. If this port is blocked,
connection cannot be established.
Mail Server – Port for
communication with SMTP server.
This port is used for device
discovery all available Cynap and
Visualizer in the network by
vSolution applications (uses
Multicast IP address
239.255.255.250). If this port is
blocked, device discovery is not
possible
This port is used for device
discovery. If this port is blocked,
device discovery is not possible.
This port is used for control
purposes. If this port is blocked, no
control is possible
For Zoom clients and meeting
connector
For Zoom clients
For Zoom clients
WolfVision GmbH
Oberes Ried 14
A-6833 Klaus / AUSTRIA
8802
3478
3479
8801 –
8810
TCP
UDP
UDP
UDP
Outbound
Outbound
Outbound
Outbound
19
Tel. +43-5523-52250
Fax +43-5523-52249
E-Mail: [email protected]
www.wolfvision.com
For Zoom clients
For Zoom clients
For Zoom clients
For Zoom clients
WolfVision GmbH
Oberes Ried 14
A-6833 Klaus / AUSTRIA
Tel. +43-5523-52250
Fax +43-5523-52249
E-Mail: [email protected]
www.wolfvision.com
5. Differences in Open Mode / Protected Mode
When using Cynap Core PRO, it is possible to choose between either open mode or
protected mode.
This different mode can be selected using Cynap Core PRO settings.
Modes:
Open Mode
The open is intended for quick and easy connections and BYOD without the need of high
security and big effort for administration.
When Open Mode is active, all available devices can connect to Cynap Core PRO.
In the Open Mode, Airplay PIN can be used to prevent disturbance of extern Apple devices.
The PIN will be shown on the connected display only HDMI.
Protected Mode
Is a password protected mode to prevent misuse and disturbances
• Users with knowledge of the password can connect to Cynap Core PRO
• Users who knowing the security PIN, the PIN will be displayed on the selected
interface(s)
• Users can connect when Cynap Core PRO is awaiting a mirror connection
For more information, please refer to the manual.
20
WolfVision GmbH
Oberes Ried 14
A-6833 Klaus / AUSTRIA
Tel. +43-5523-52250
Fax +43-5523-52249
E-Mail: [email protected]
www.wolfvision.com
6. BYOD
Cynap Core PRO is designed to make it as easy as possible for users to connect to it. Cynap
Core PRO supports integrated mirroring protocols in its operating system. Users can connect
to Cynap Core PRO without needing any additional software. The mobile platforms are
AirPlay for iOS devices and Miracast for Android and Windows devices. Regarding laptop
and computer operating systems, AirPlay is also supported for Mac OS X. Windows Intel
Wireless Display is also supported, and this integrates natively with Windows 8.1.
AirPlay
vSolution Cast
for iOS (App)
Miracast
vSolution Cast
(Windows)
vSolution Connect
Chromecast
Screen Mirroring
Support for iOS 5.0 (released 2011) and above, or OS X 10.8 Mountain
Lion (released 2012) and above. AirPlay is transmitted via Ethernet /
WLAN. It can be used for displaying up to four sources.
For use in network environments where the Bonjour service (device
discovery protocol) has been disabled.
Miracast is based on a Wi-Fi direct connection. This means that
Miracast can only be used in close proximity to Cynap Core PRO. Due
to the direct communication with a device, only one connection to
Cynap Core PRO is possible at the same time (HDCP will be not
supported). When using Microsoft Windows PCs or tablets, the use of
vSolution Cast is recommended.
In applications where a Wi-Fi direct connection is not possible due to
the installation, multiple Windows devices can be connected at the
same time using the alternative vSolution Cast.
vSolution Connect is a professional presentation tool which offers an
alternative to mirroring for Android and iOS. Mirroring has some
disadvantages, and can, for example, allow incoming messages or
calendar pop-ups to be visible on-screen to all participants during a
presentation.
Support for Chromecast capable devices. Chromecast is transmitted
via Ethernet / WLAN. It can be used for displaying up to four sources.
AirPlay, Chromecast, Miracast and vSolution Cast are based on device discovery
technologies for maximum ease of use. Therefore it is necessary that the appropriate
services (See Firewall rules) are available. Alternatively, when using vSolution Cast, a Cynap
Core PRO IP address can be entered manually. On Windows systems, vSolution Cast can
either be run temporarily by users, or permanently installed (copied). The application can
also be used from a USB stick without needing administrator rights, however with the
restriction that no sound is transmitted.
Switching Cynap Core PRO to standby closes all connections.
21
WolfVision GmbH
Oberes Ried 14
A-6833 Klaus / AUSTRIA
Tel. +43-5523-52250
Fax +43-5523-52249
E-Mail: [email protected]
www.wolfvision.com
7. Document and media player
Cynap Core PRO can present almost all commonly used document and video file formats.
This functionality is built in to Cynap Core PRO and no additional applications need to be
installed.
Cynap Core PRO also supports different storage media for presentation of documents and
video.
The following storage media are available for Cynap Core PRO.
- Internal storage
- USB flash drive
- Network Drive
- Cloud services
The following media formats are supported:
- Supported pictures file formats:
GIF, JPEG, BMP,PNG
- Supported video file formats:
AVI, WMV, MOV, MP4, DivX, MKV, M4V, OGV
- Supported document file formats: PDF, Word, PowerPoint, Excel
- Supported audio file formats:
MP3, MKA, OGA, OGG, WMA
22
WolfVision GmbH
Oberes Ried 14
A-6833 Klaus / AUSTRIA
Tel. +43-5523-52250
Fax +43-5523-52249
E-Mail: [email protected]
www.wolfvision.com
8. Network Stream (input)
Cynap Core PRO has a built-in streaming client which is capable of receiving broadcast
video content over the network.
Up to four Stream sources can be defined and individually named in the GUI settings (Input).
Add new Input Stream
Input name
Input mode
Input URL
Allows adding up to four network streams selectable as
source (click the + symbol).
Gives the source an individual name for easy identification
Defines the kind of stream.
• None, disables receiving this stream
• Generic allows streams using UDP and TCP protocol
• RTSP / RTP over TCP allows TCP protocol only
Record Stream Input URL defines the source of the stream
Example:
Network stream input with two devices, one from Meeting Room 1 Cynap to Meeting Room 2
Cynap Core PRO and one IP Camera.
23
WolfVision GmbH
Oberes Ried 14
A-6833 Klaus / AUSTRIA
Tel. +43-5523-52250
Fax +43-5523-52249
E-Mail: [email protected]
www.wolfvision.com
At the Cynap Core PRO Meeting Room 2 are two network stream input configured with the
following settings.
After saving configuration the new two sources (IP Camera, Cynap Core PRO Meeting Room
1) are available.
At the Cynap Meeting Room 1 the RTSP Stream is enabled and Streaming must be started.
Then choose the sources IP Camera and Cynap Core PRO Meeting Room 2 and then
contents will be displayed Cynap Core PRO Meeting Room 2.
24
WolfVision GmbH
Oberes Ried 14
A-6833 Klaus / AUSTRIA
Tel. +43-5523-52250
Fax +43-5523-52249
E-Mail: [email protected]
www.wolfvision.com
9. Control of Peripheral Devices
Cynap Core PRO is able to send up to 10 commands to connected network devices, e.g. to
fully power up the connected projector. This feature will be triggered by power events of
Cynap Core PRO.
The peripheral devices, like projectors, monitor, lightings, windows shades, etc. need to be in
the same network as Cynap Core PRO.
Command enable
Name
Description
Event
Protocol
IP address
Port
Hex Command
Password
Enable / disable certain commands (entered command
settings will be not deleted
To give the command an individual name (like “projector”)
To give the command a detailed description (like “power up”)
To define at which power state of Cynap Core PRO the
command will be sent (Power ON or Power OFF). Select
event None to delete this entry.
Defines the used network protocol (TCP,UDP or PJLink)
Defines the destination, enter the address of the third party
device
Defines at which network port the command will be sent
(note documentation of the third party device and firewall
settings)
Enter the command according documentation of the third
party device.
Available when protocol PJLink is selected
25
WolfVision GmbH
Oberes Ried 14
A-6833 Klaus / AUSTRIA
Tel. +43-5523-52250
Fax +43-5523-52249
E-Mail: [email protected]
www.wolfvision.com
10. Cloud services
Cynap Core PRO supports Google Drive ,Dropbox, Jianguoyun, OneDrive and WebDAV
cloud services. These services can be enabled or disabled in the settings. For specific
firewall settings, check the individual service provider.
11. Network Drive
Cynap Core PRO allows direct access to network drives (writeable or read-only). A default
drive can be specified to simplify the upload functionality of a recording or snapshot.
Up to 10 network drives can be configured in the network drive settings.
CIFS and NFSv3 file systems are supported.
12. User interface
Cynap Core PRO can be controlled using any current standard browser. The user interface
has been developed using the latest web programming standards, and this means that there
is no need for additional add-ons or plugins such the Java Platform, in order to have full
control of Cynap Core PRO. HTML5 technology only requires a browser that can handle
JavaScript and Websockets, and this has been state-of-the-art for the last few years.
You can also adjust the settings using the remote control (optional). The remote control uses
the 2.4 GHz band. The remote control has a built-in gyro sensor and can be used as a digital
laser pointer.
Cynap Core PRO can also be used in combination with room management systems.
Communication is possible via the Wolfprot protocol. More information about this protocol
can be found in the support section of our website www.wolfvision.com .
The vSolution Control app allows smartphones / tablets (iOS, Windows, Android) to control
Cynap Core PRO directly via WLAN. More information about the vSolution Control App can
be found on in the support section of our website www.wolfvision.com .
26
WolfVision GmbH
Oberes Ried 14
A-6833 Klaus / AUSTRIA
Tel. +43-5523-52250
Fax +43-5523-52249
E-Mail: [email protected]
www.wolfvision.com
13. Hardware and OS
Cynap Core PRO uses a Linux operating system. The distribution is a WolfVision specific
variant, which in addition to the Linux kernel contains only the individual libraries and
packages required for the functionality of Cynap Core PRO. This operating system is
efficient, secure and lean. The operating system is installed after the installation process, and
every update is installed to a read-only partition that cannot be changed after the installation
process. This feature and the strict separation of system and user data, such as pictures,
videos etc. ensures a very high level of system security. The system structure is protected
against any external access, and it does not require additional security programs (antivirus,
firewall, etc.). The Cynap Core PRO system includes all viewer and software packages, and
no additional licenses are required.
The current hardware specifications, connectors, delivery, and technical specifications can
be found on our website www.wolfvision.com.
A 19” rack mount is available as an optional accessory if required for installing Cynap Core
PRO (2HE).
14. Administration
Cynap Core PRO can be managed using the vSolution Link software.
With vSolution Link software, administration tasks can be performed for multiple Cynap Core
PRO systems. With this admin tool, you can perform central firmware upgrades as well as
determining the state of Cynap Core PRO and Wake-on-LAN (WoL). You can also create,
manage, and distribute a settings profile to all Cynap Core PRO systems using vSolution
Link software.
More information about vSolution Link software can be found in the support section of our
website www.wolfvision.com.
27
WolfVision GmbH
Oberes Ried 14
A-6833 Klaus / AUSTRIA
Tel. +43-5523-52250
Fax +43-5523-52249
E-Mail: [email protected]
www.wolfvision.com
15. Bandwidth Measurement Data
This bandwidth measurement data has been taken using a notebook PC with a Windows
operating system. The computer was connected to Cynap Core PRO via WLAN, and was
operating in network infrastructure mode.
15.1.
PowerPoint Presentation
Presentation with text and a few graphics are displayed from the notebook and are mirrored
to Cynap Core PRO using vSolution Cast Software to a single connected client. (Traffic Out)
Max: 2,9 Mbit/s
15.2.
Multimedia from Notebook to Cynap Core PRO using vCast
Software
1080p video (Big Buck Bunny) is displayed on the notebook and is mirrored using the
vSolution Cast Software to a single connected client. (Traffic Out)
Max: 7 Mbit/s
28
WolfVision GmbH
Oberes Ried 14
A-6833 Klaus / AUSTRIA
Tel. +43-5523-52250
Fax +43-5523-52249
E-Mail: [email protected]
www.wolfvision.com
16. Client System Requirements
Requirement Airplay Mirroring OS X Mountain Lion v10.8 (Release 2012) or later:
Product
iMac
Mac mini
MacBook Air
MacBook Pro
Mac Pro
Version
Mid 2011 or later
Mid 2011 or later
Mid 2011 or later
Early 2011 or later
Late 2013 or later
Requirement Airplay Mirroring iOS 5.0 (Release 2011) or later:
Product
iPhone
iPad
iPad
iPod touch
Version
4 or later
2 or later
mini or later
5th generation or later
Requirement Miracast:
Product
Android
Microsoft Windows
Windows Phone
Blackberry
Version
4.4.2 or later
8.1, 10, 11
Hardware with Miracast support required
8.1, 10
10.2.1 or later
Requirement Chromecast:
Product
Android
Microsoft Windows
Version
4.0.3 or later
(Chromecast required)
7, 8.1, 10
(Chromecast Browser Plugin required)
29
WolfVision GmbH
Oberes Ried 14
A-6833 Klaus / AUSTRIA
17. Index
Version Date
Changes
1.0
11.06.2021
Created
1.1
31.07.2023
- Minor text edits
- Addition Firewall rules
- Illustrations updated
1.2
02.10.2023
- Minor text edits
1.3
18.10.2023
- Addition Firewall rules
30
Tel. +43-5523-52250
Fax +43-5523-52249
E-Mail: [email protected]
www.wolfvision.com
">