This manual contains proprietary information of Zebra Technologies Corporation. It is intended solely for the information and use of parties operating and maintaining the equipment described herein. Such proprietary information may not be used, reproduced, or disclosed to any other parties for any other purpose without the expressed written permission of Zebra Technologies Corporation.

Product Improvements

Since continuous product improvement is a policy of Zebra Technologies Corporation, all speciﬁcations and signs are subject to change without notice.

FCC Compliance Statement

NOTE: This equipment has been tested and found to comply with the limits or a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet or circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

WARNING: Exposure to Radio Frequency radiation. To conform to FCC RF exposure requirements this device shall be used in accordance with the operating conditions and instructions listed in this manual. Note that there are several radio options available with this printer. Additional regulatory information is contained in later sections devoted to each radio individually.

NOTE: This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with the unit to insure compliance.

Changes or modiﬁcations to this unit not expressly approved by Zebra Technologies Corporation could void the user’s authority to operate this equipment.

Canadian Compliance Statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada.

“IC:” before the equipment certification number signifies that the Industry Canada technical specifications were met. It does not guarantee that the certified product will operate to the user’s satisfaction.

Agency Approvals and Regulatory Information

• Design certiﬁed by TUV

• Canadian STD RSS-210

• EN60950: 2000 Safety Standard • NOM/NYCE (Mexico)

• C-Tick (Australia)

• FCC part 15

• EN55024:1998 European Immunity Standard

• EN55022:1998 Class B European

Electromagnetic Radiation Standard

Liability Disclaimer

Inasmuch as every effort has been made to supply accurate information in this manual,

Zebra Technologies Corporation is not liable for any erroneous information or omissions.

Zebra Technologies Corporation reserves the right to correct any such errors and disclaims liability resulting therefrom.

No Liability for Consequential Damage

In no event shall Zebra Technologies Corporation or anyone else involved in the creation, production, or delivery of the accompanying product (including hardware and software) be liable for any damages whatsoever (including, without limitation, damages for loss of business proﬁts, business interruption, loss of business information, or other pecuniary loss) arising out of the use of or the results of use of or inability to use such product, even if Zebra Technologies Corporation has been advised of the possibility of such damages.

Because some states do not allow the exclusion of liability for consequential or incidental damages, the above limitation may not apply to you.

continued

MZ Series User Guide

Copyrights

The copyrights in this manual and the label print engine described therein are owned by

Zebra Technologies Corporation. Unauthorized reproduction of this manual or the software in the label print engine may result in imprisonment of up to one year and ﬁnes of up to

$10,000 (17 U.S.C.506). Copyright violators may be subject to civil liability.

This product may contain ZPL izer

Circuit; E3

, ZPL II

, and ZebraLink tm

programs; Element Energy Equal-

ZebraLink and all product names and numbers are trademarks, and Zebra, the Zebra logo,

ZPL, ZPL II, Element Energy Equalizer Circuit, and E3 Circuit are registered trademarks of

Monotype

, Intellifont

and UFST

are trademarks of Monotype Imaging, Inc. registered in the United States Patent and Trademark Ofﬁce and may be registered in certain jurisdictions.

Andy

Kai

TM , CG Palacio TM , CG Century Schoolbook

, Monotype Mincho

and Monotype Sung

Inc. and may be registered in some jurisdictions.

HY Gothic Hangul TM

, CG Triumvirate TM , CG Times TM , Monotype

are trademarks of Monotype Imaging,

Angsana TM

is a trademark of Hanyang Systems, Inc.

is a trademark of Unity Progress Company (UPC) Limited.

Andale

, Arial

, Book Antiqua

, Corsiva

, Gill Sans

, Sorts

and Times New Roman

are trademarks of The Monotype Corporation registered in the United States Patent and Trademark Ofﬁce and may be registered in certain jurisdictions.

Century Gothic™, Bookman Old Style TM and Century Schoolbook TM are trademarks of The

Monotype Corporation and may be registered in certain jurisdictions.

HGPGothicB is a trademark of the Ricoh company, Ltd. and may be registered in some jurisdictions.

Univers TM is a trademark of Heidelberger Druckmaschinen AG, which may be registered in certain jurisdictions, exclusively licensed through Linotype Library GmbH, a wholly owned subsidiary of Heidelberger Druckmaschinen AG.

Futura ® is a trademark of Bauer Types SA registered in the United States Patent and Trademark Ofﬁce and may be registered in some jurisdictions.

TrueType

is a trademark of Apple Computer, Inc. registered in the United States Patent and

Trademark Ofﬁce and may be registered in certain jurisdictions.

All other product names are the property of their respective owners.

All other brand names, product names, or trademarks belong to their respective holders.

MZ Series User Guide

Document Conventions

The following conventions are used throughout this document to convey certain information:

If you are viewing this guide online, click the underlined text to jump to a related Web site. Click on italic text (not underlined) to jump to that location in this manual.

Cautions, Important, and Note

Caution • Warns you of the potential for electrostatic discharge.

Caution • Warns you of a potential electric shock situation.

Caution • Warns you of a situation where excessive heat could cause a burn

Caution • Advises you that failure to take or avoid a speciﬁc action could result in physical harm to you.

Caution • Advises you that failure to take or avoid a speciﬁc action could result in physical harm to the hardware.

Important • Advises you of information that is essential to complete a task.

Note • Indicates neutral or positive information that emphasizes or supplements important points of the main text.

MZ Series User Guide

Introduction to the MZ Series

Thank you for choosing one of our Zebra

MZ™ series

Mobile Printers. These rugged printers are sure to become productive and efﬁcient additions to your workplace thanks to their innovative design. Because they are made by Zebra

Technologies, you’re assured of world-class support for all of your bar code printers, software, and supplies.

• This user’s guide gives you the information you will need to operate any MZ series printer.

• The MZ series uses the CPCL programming language.

To create and print labels using the CPCL language, refer to the Mobile Printer Programming Guide and our

Label Vista™ label creation program which are both available on our Web site at www.zebra.com.

Unpacking and Inspection

Inspect the printer for possible shipping damage:

• Check all exterior surfaces for damage.

• Open the media cover (refer to “Loading the Media” in the Getting Ready to Print section) and inspect the media compartment for damage.

In case shipping is required, save the carton and all packing material.

Reporting Damage

If you discover shipping damage:

• Immediately notify and ﬁle a damage report with the shipping company. Zebra Technologies Corporation is not responsible for any damage incurred during shipment of the printer and will not cover the repair of this damage under its warranty policy.

• Keep the carton and all packing material for inspection.

• Notify your authorized Zebra re-seller.

MZ Series User Guide

Figure 1: MZ Series Overview (MZ 220 Illustrated)

1. Feed Switch

2. Media Status Light

3. USB Port

4. Battery Charging Receptacle

5. Media Sensor

6. Media Cover

7. Platen

8. Printhead

9. Latch Release Button

10. Communications Status

Indicator

11. IR window

12. Charge Status Indicator

13. Power Switch

14. Power Indicator

15. Belt Clip

16. Battery Door Latch

17. Battery Compartment Cover

18. Battery Pack

19. External Charge Contacts

MZ Series User Guide

Getting Ready to Print

Battery

Installing the Battery

Important • Batteries are shipped partially charged. Remove any protective packaging from new battery packs prior to use.

Figure 2: Installing the Battery

1. Use a coin to rotate the

Battery Compartment lock

turn as shown.

Battery Pack

Note location of label

2. Remove the Battery

Compartment Cover

3. Plug the Battery

Pack connector into the

Printer.

4. Re-install the Battery Compartment Cover and rotate the lock back

turn to lock it in place .

Ensure the battery leads are not pinched prior to replacing the battery cover.

MZ Series User Guide

When the battery is ﬁrst installed, the printer power and charge indicators should indicate the battery is not fully charged (see “Charging the Battery” below and “Operator

Controls”).

You must charge the battery fully before using the printer for the ﬁrst time.

Charging the Battery

Preparing the Charger Power Supply

Before charging the battery for the ﬁrst time, you must prepare the Charger Power Supply. Refer to Figure 3

Figure 3: Preparing the Charger Power Supply

1. Remove the power supply from its box. Remove and discard the shipping ring from the mains receptacle cavity.

2. Verify that the mains adapter shipped with your Printer is the correct one for your region.

UK -230 VAC

US/Japan-100-110 VAC

China-220 VAC

Shipping Ring

Remove and discard

Euro -230 VAC

Aust-240

Mains Adapter

3. Install the mains adapter into the Power Supply by hooking the top edge into the mains receptacle cavity, and rotating it until it snaps into place.

MZ Series User Guide continued

Figure 4: Charging the Battery

MZ Series Charger Power Supply p/n AT17947-1

110-240 VAC 50-60 Hz 0.6A Input; 12 VDC 1.25 A output

Plug into AC receptacle

Charger Jack

12 VDC

Charging the battery

Refer to Figure 4.

1. Plug the Charger Power Supply into the appropriate A.C. wall receptacle. Then insert the charge cable into the printer’s charger jack.

2. The printer’s charger indicator will indicate the status of the charger as follows:

• An amber light indicates the battery is charging, and that the battery is less than 90% charged.

• A green light indicates the battery is fully charged. The battery is ready for use.

Approximate Charge Times :

Batteries are fully charged after 2.5 hours from the low-battery shut-off state. Partially discharged batteries will take less time to charge.

NOTES: Use of the printer while charging will increase charge times.

Charge times are for completely discharged batteries.

As a safety feature the battery will stop charging after 4.5 hours regardless of the battery’s charge state.

MZ Series User Guide

MZ Series Quad Power Station

The MZ series Quad Power Station is designed to dock and charge up to four MZ series printers of either type simultaneously.

1. Ensure that the Power Station has been installed properly per its instruction manual. Ensure that the power supply is properly connected and its power indicator light is on.

2. Slide a printer into any one of the four docking bays as shown in Figure 5.

NOTES: If you are using a shoulder strap, ensure it is pulled away from the printer when installing in the Power Station.

Do not use the printer when it is installled in the Power

Station

The printer’s charge status indicator will turn amber if the printer is properly inserted and the battery is less than

90% charged.

The printer’s charge indicators will allow you to monitor the

Figure 5: MZ Series Quad Power Station

MZ 220 Printer

MZ 320 Printer

Slide Printer into docking bay

Green (Power)

Indicator

Amber/Green (Charge)

Indicator

MZ Series User Guide

charging process. Refer to the Controls section of this manual for more information.

Battery Safety

Caution • Avoid accidental short circuiting of any battery. Allowing battery terminals to contact conductive material will create a short circuit which could cause burns and other injuries or could start a ﬁre.

Important • Always dispose of used batteries properly. Refer to

Appendix D for more battery recycling information.

Caution • Use of any charger not approved speciﬁcally by Zebra for use with its batteries could cause damage to the battery pack or the printer and will void the warranty.

Read carefully and always observe the safety guidelines for Li-Ion batteries provided with each Battery Pack.

Charger Safety

Do not place the Power Station in locations where liquids or metallic objects may be dropped into the charging bays.

Use care when installing either the Charger Power Supply shipped with the printer or the power supply supplied with the MZ series

Power Station. Do not block the ventilating slots on the top and bottom covers of either power supply.

Ensure that the Charger Power Supply is plugged into a power source which will not accidently be turned off if you will be charging batteries overnight.

MZ Series User Guide

Loading the Media (All models)

1. Open the printer: Refer to Figure 6.

• Press the latch release button on the top of the printer as shown at “1” below. The media cover will ﬂip open automatically revealing the media compartment.

2. Load the media: Refer to Figure 7

• Insert the roll of media into the media compartment.

Ensure that the media pulls off the core in the direction shown in Figure 6.

3. Close the Media Cover:

Refer to Figure 8.

• Pull a short length of media out of the printer

• Close the Media Cover ﬁrmly and ensure it is securely latched on both sides..

• Turn on the printer and press the Feed button.

The printer will advance media until the Feed button is released. Verify the media is feeding properly and without binding or skewing sideways

Figure 6: Opening the MZ Printer (MZ 220 shown)

Latch Release

Button

Media Compartment

MZ Series User Guide continued

Figure 7: Installing Media

Media Roll

Note direction media pulls off the roll.

Figure 8: Closing the Media Cover

Pull a short length of media out of the Printer

Media Cover

Ensure both sides of the media cover are securely latched when closed.

MZ Series User Guide

Operator Controls

MZ series printer controls are detailed below and in Figure 9.

The printer has two control buttons and four multipurpose indicators.

The

Power Button turns the printer on and off.

The Feed Button advances a length of media until it is released.

The

Green/Amber indicator to the left of the Power Button indicates the status of the printer’s built-in charger:

• The indicator is off indicates the battery is not being charged.

• If the indicator is amber the battery is being charged.

• If the indicator is green, the battery is fully charged.

The Green Indicator between the Power and Feed buttons has two states:

• A rapidly blinking light indicates a low battery condition.

• A steadily lit indicator means that power is on and the battery charge level is sufﬁcient for use

The Amber Indicator to the right of the Feed button is an error indicator.

• An un-lit indicator means there is no error condition and the printer can be used.

• A blinking indicator could mean one of two conditions exist, which will inhibit printer operation:

1. There is no media loaded.

2. The media cover is open.

3. If both the above conditions are met and the error light is still ﬂashing, there could be no application loaded in the printer, or the application could have become corrupted.

The Blue Indicator just above the product I.D. label is a communications indicator. Its functions vary depending on the wireless communications option installed in the printer.

• If the printer uses only standard IrDA

wireless communication:

A blinking light indicates data is being received from a linked IrDA device.

• If the printer has a Bluetooth™ radio option:

1. A steady light indicates the printer has paired with an-

MZ Series User Guide

other Bluetooth device.

2. A blinking light indicates that the printer is receiving data via Bluetooth communications.

• If the printer has an 802.11b/g radio installed:

1. A steady light indicates the printer has associated with a wireless Local Area Network (WLAN).

2. A blinking light indicates that the printer is attempting to associate with a WLAN.

Figure 9: Printer Controls

Power Button

Press and hold to turn unit on.

Press again to turn unit off.

Charge Light

(Green/Amber)

Green indicates the battery fully charged. Amber indicates the battery is less than 90% charged.

Power Light (Green)

Indicates power status and battery condition.

A steadily lit indicator means the battery has more than a 30% charge remaining. A blinking indicator means the battery has less than a

30% charge remaining.

Feed Button

Press to advance the media. Release to stop.

Media Status Light

(Amber)

When off Indicates normal operation.Blinking indicates either no media or that the media compartment is open.

IrDA Window

IrDA enabled devices must be located within the printer’s IR zone for IR communications to occur.

Refer to the IR Communications section.

Communication Light (Blue)

When lit steadily indicates a wireless communications link is established, when blinking indicates data transmission.

MZ Series User Guide

Verify the Printer Is Working

Before you connect the printer to your computer, portable data terminal or wireless LAN, make sure that the printer is in proper working order. You can do this by printing a conﬁguration label using the “two key reset” method. If you can’t get this label to print, refer to “Troubleshooting”.

Printing a Conﬁguration Label

1. Turn the printer off. Load the media compartment with journal media (media with no black bars printed on the back)

2. Press and hold the Feed Button.

3. Press and release the Power button and keep the Feed button pressed. When printing starts, release the Feed button.

The unit will print a line of interlocking “x” characters to ensure all elements of the print head are working, print out the version of software loaded in the printer and then print two reports.

The first report indicates model, ROM version, serial number, etc. The second report prints out more detailed information on the printer’s configuration and parameter settings. If no second report appears, there is no application loaded. (See the Troubleshooting Section for sample printouts and a further discussion on how to use the configuration label as a diagnostic tool.)

Connecting the Printer

The printer must establish communications with a host terminal which sends the data to be printed. Communications occur in four basic ways:

• Via a cable using the USB 2.0 protocol. USB drivers are included in the Zebra Universal Driver which can be downloaded from www.zebra.com.

• Via the industry standard IrDA protocol. IR capability is standard with MZ series printers.

• By means of an optional Bluetooth short range radio link.

• By means of a wireless LAN (Local Area Network) using an optional radio per 802.11b/g speciﬁcations.

MZ Series User Guide

Cable Communication

The small connector on the USB cable plugs into the printer.

The connectors are keyed to assure correct alignment; do not try to force the cable if it does not plug in. The other end of the cable must be plugged into the host terminal as shown in

Figure 10, or the USB port on a computer as shown in Figure

11. The MZ series utilizes the USB Open HCI interface driver allowing it to communicate with Windows

based devices.

USB drivers are included in the Zebra Universal Driver which can be downloaded from the Zebra Web site. Other terminals or communications devices may require the installation of special drivers to use the USB connection. Consult the factory for further details.

Figure 10: Cable Communications

USB Communications

Cable to Terminal

Refer to Appendix A for details.

Communications

Port

Figure 11: Communications with a P.C.

USB Communications

Cable to Computer

Refer to Appendix A for details.

Communications

Port

MZ Series User Guide

IR Communications

Ensure that the terminal sending and receiving data is within the shaded zone depicted in Figure 12. The IR window on the front of the printer must face the corresponding window on the terminal to properly send and receive signals. The maximum distance IrDA signals can be transmitted reliably is 1M

(39”).

63.5 cm (25”)

4.258"

30.110°

87.0°

87°

30.61°

MZ Series User Guide

Wireless Communications with Bluetooth™

Bluetooth is a worldwide standard for the exchange of data between two devices via radio frequencies. Bluetooth radios are relatively low powered to help prevent interference with other devices running at similar radio frequencies. This limits the range of a Bluetooth device to about 10 meters (32 feet).

Both the printer and the device it communicates with must follow the Bluetooth standard. Only one of the radio options can be installed in the printer at one time and the antenna used for these transmitters must not be co-located or must not operate in conjunction with any other antenna.

Bluetooth Networking Overview

Each Bluetooth enabled MZ series printer is identiﬁed by a unique Bluetooth Device Address (BDA) loaded into the printer when manufactured. In order to exchange data, two

Bluetooth enabled devices must establish a connection.

Bluetooth software is always running in the background, ready to respond to connection requests. One device (known as the master) must request a connection with another. The second device (the slave) then accepts or rejects the connection. A Bluetooth enabled MZ series printer will normally act as a slave creating a miniature network with the terminal sometimes referred to as a “piconet.”.

For the most part, communications using the Bluetooth protocol are initiated and processed without any operator intervention.

MZ Series User Guide

WLAN Overview

All MZ series printers can be equipped with radios using the industry standard 802.11b/g protocol. MZ series printers will have the FCC I.D. number of the radio on the serial number label on the back of the unit.

MZ series printers with the Zebra 802.11b/g WLAN radio option can be identiﬁed by the FCC ID:

I28MD-ZLAN11G on the serial number label on the back of the printer.

Methods of establishing communications to MZ series printers will vary with each LAN application. General information on establishing WLAN communications can be found in either the ”CPCL Programmers Manual” or the

“Zebra Mobile Printer Wireless Conﬁguration Guide” both available on-line at www.zebra.com.

More information and LAN conﬁguration utilities are included in Zebra’s Label Vista™ program (version 2.8 and later).

Label Vista may be downloaded from the Zebra Web site.

Setting Up the Software

MZ series printers use Zebra’s CPCL Programming language which was designed for mobile printing applications. CPCL is fully described in the ”CPCL Programmers Manual”, available on-line from the Zebra Web site.

You can also use Label Vista™, Zebra’s Windows

based label creation program which uses a graphical interface to create and edit labels in the CPCL language.

Refer to Appendix F for tips on downloading the Label Vista application from Zebra’s Web site.

MZ Series User Guide

Radio Regulatory Information

Zebra Bluetooth Radios MZ-ZBR3

Caution • Exposure to Radio Frequency Radiation. The radiated output power of this internal Bluetooth radio is far below the FCC radio frequency exposure limits. The internal Bluetooth radio operates within guidelines found in radio frequency safety standards and recommendations. Do not use the printer in an unauthorized manner.

Note • The following section only applies when the MZ-ZBR3

(FCC ID: I28MD-BTC2TY6) Bluetooth Radio is installed in a MZ series printer. The antenna used for this transmitter must not be co-located or must not operate in conjunction with any other antenna.

European Regulatory Information for this Radio

This device is intended for use in all EU and EFTA member states.

Europe – EU Declaration of Conformity

This device complies with the essential requirements of the R&TTE Directive

1999/5/EC. The following test methods have been applied in order to prove presumption of compliance with the R&TTE Directive 1999/5/EC:

• EN55022:1998

European Immunity Standard

• EN 60950: 2000

Safety of Information Technology Equipment

• EN 300 328-2 V1.4.1 (2003-04)

Technical requirements for spread-spectrum radio equipment

• EN 301 489-1/-17 V1.5.1/1.2.1 (2003-12) -17 v1.2.1 (2002-08)

EMC requirements for spread-spectrum radio equipment.

This device is a 2.4 GHz wireless LAN transceiver, intended for indoor home and ofﬁce use in all EU and EFTA member states.

Important Notice

This device is a portable RF printer intended for commercial and industrial use in all EU and EFTA member states.

MZ Series User Guide

WLAN Module Using 802.11b/g Radio

The following section only applies when the 802.11b/g

WLAN module (With FCC ID: I28MD-ZLAN11G) is installed in a MZ series printer. Only one of the radio options can be installed in the printer at one time and the antenna used for these transmitters must not be co-located or must not operate in conjunction with any other antenna.

MZ series printers have the FCC ID number on a label on the back of the unit.

Caution • Use of a MZ series printer with the radio module marked with FCC ID: I28MD-ZLAN11G meets the FCC requirements for radio frequency (RF) radiation exposure in the standard body worn configuration with no minimum separation. In this configuration, which applies whether the belt clip or shoulder strap is used, the face of the printer from which paper is transported is facing away from the user’s body. The standard configuration must always be used when the printer is body worn.

The MZ 220 and MZ 320 printers with this radio option have been SAR tested. The maximum SAR value measured for each model is listed below:

Model

MZ 220

MZ 320

SAR value W/Kg 1g average)

)

.049

.038

European Regulatory Information for this Radio

BE CY

FI FR

CZ DK

DE GR

SK SI ES SE GB

Note: -Member states in the EU with restrictive use for this device are crossed out!

This device is also authorized for use in all EFTA member states (

CH, IS, LI, NO)

Important Notice:

This device is a portable RF printer intended for commercial and industrial use in all EU and

EFTA member states except in France where restrictive use applies.

continued

MZ Series User Guide

Europe – EU Declaration of Conformity

This device complies with the essential requirements of the R&TTE Directive

1999/5/EC. The following test methods have been applied in order to prove presumption of compliance with the R&TTE Directive 1999/5/EC:

• EN55022:1998

European Immunity Standard

• EN 60950: 2000

Safety of Information Technology Equipment

• EN 300 328-2 V1.2.1 (2001-12)

Technical requirements for spread-spectrum radio equipment

• EN 301 489-17 V1.2.1 (2002-08)

EMC requirements for spread-spectrum radio equipment.

This device is a 2.4 GHz wireless LAN transceiver, intended for indoor home and ofﬁce use in all EU and EFTA member states, except in France where restrictive use applies.

The use of this frequency band in France is subject to restrictions. You may only use channels 10 and 11 (2457 and 2462 MHz) on French territory, except in those

French departments as listed in the table below where channels 1-13 (2412-2472

MHz) may be used. For more information see http://www.anfr.fr/ and/or http:// www.art-telecom.fr

Ain

Aisne

Allier

Hautes Alpes

Ardennes

Ariege

Aube

Aude

Aveyron

Charente

Correze

Corse Sud

Haute Corse

Cote d’Or

Dordogne

Doubs

Drome

Eure

Gers

Ille et Vilaine

36 Indre 69

Indre et Loire

Jura

Loir et Cher

Loire

Loiret

Manche

Meurthe et Moselle

Meuse

Moselle

Nievre

Nord

Oise

Orne

Puy de Dome

64 Pyrenees Atlantique 92

65 Hautes Pyrenees 93

66 Pyrenees Orientales 94

67 Bas Rhin

68 Haute Rhin

Rhone

Haute Saone

Saone et Loire

Sarthe

Paris

Seine et Marne

Yvelines

Deux Sievres

Tarn et Garonne

Vaucluse

Vienne

Vosges

Yonne

Territoire de Belfort

Essonne

Hauts de Seine

Seine St Denis

Val de Marne

MZ Series User Guide

Wearing the Printer

Belt Clip

Refer to Figure 13. All MZ series printers are have a belt clip installed as a standard feature. To use: hook the clip over your belt, and ensure that the clip is securely attached to the belt. The belt clip will pivot slightly to allow you to move freely while wearing the printer.

Clip printer to belt

Figure 13: Using the Belt Clip

MZ Series User Guide continued

Adjustable Shoulder Strap

Refer to Figure 14 if you have ordered the shoulder strap option for your printer. Secure each end of the shoulder strap as shown below. Use the main buckle on the shoulder strap to adjust to the desired length.

NOTE: If you are using a shoulder strap, ensure it is pulled away from the printer when installing in the Power Station. See page 13.

Thread the free end of the shoulder strap through one of the slots on the belt clip

Thread the free end of the shoulder strap through the buckle and pull tight to adjust.

Secure the other end of the strap in the remaining slot on the belt

Pull Strap here to lengthen

Hold Buckle

Pull Strap here to shorten

Once the shoulder strap is secured, slide the buckle as shown until you achieve the desired length.

Figure 14: Using the Optional Shoulder Strap

MZ Series User Guide

Preventive Maintenance

Extending Battery Life

• Always observe the safety precautions in the Lithium-

Ion Battery Technical Bulletin included with each Battery

Pack.

• Never expose the battery to direct sunlight or temperatures over 104° F (40° C).

• Do not charge the battery when the temperature exceeds

113° F (45° C).

• Always use a Zebra power supply designed speciﬁcally for the MZ series printers. Use of any other kind of power supply may damage the battery.

• Use the correct media for your printing requirements. An authorized Zebra re-seller can help you determine the optimum media for your application.

• If you print the same text or graphic on every label, consider using a pre-printed label.

• Choose the correct print darkness, and print speed for your media.

NOTE: Use of label media in an MZ series printer requires a “Tone” setting of 50 for best results. The Tone setting can be modiﬁed by connecting the printer to a PC and using the Label Vista application.

Refer to the Cable Communications section of “Connecting the

Printer” in this manual.

• Use software handshaking (XON/XOFF) whenever possible.

• Remember that any rechargeable battery will lose its ability to maintain a charge over time. It can only be recharged a ﬁnite number of times before it must be replaced. Always dispose of batteries properly. Refer to

Appendix D for more information on battery disposal.

• If you print while charging the battery, charge times will be prolonged. Extensive printing while charging could deplete the battery enough to cause the low battery warning indicator to turn on. You should suspend printing at that time and allow the battery to re-charge completely.

continued

MZ Series User Guide

General Cleaning Instructions

Caution • To avoid possible personal injury or damage to the printer, never insert any pointed or sharp objects into the printer.

Always turn the printer off before performing any cleaning procedures.

Use care when working near the tear bar. The edges are very sharp.

Caution • The printhead can be very hot after prolonged printing.

Allow it to cool off before attempting any cleaning procedures.

Only use the cleaning pen supplied with the printer or a cotton swab saturated with alcohol for cleaning the printhead.

Caution • Use only cleaning agents speciﬁed in the following tables.

Zebra Technologies Corporation will not be responsible for damage caused by any other cleaning materials used on this printer.

MZ Series Cleaning Instructions

Area Method

Printhead

Platen

Use a Zebra cleaning pen or a

70% isopropyl alcohol solution on a cotton swab to clean the print elements from end to end

(the print elements are located in the thin gray line on the printhead).

Rotate the platen roller and clean it thoroughly with a

Zebra cleaning pen or a 70% isopropyl alcohol solution and a cotton swab.

Tear bar

Clean thoroughly with a

Zebra cleaning pen or a 70% isopropyl alcohol solution and a cotton swab.

Water dampened cloth Exterior

Media

Compartment

Interior

Brush/air blow.

Interval

After every ﬁve rolls of media

(or more often, if needed)

As needed

After every ﬁve rolls of media

(or more often, if needed)

MZ Series User Guide

Printhead

Elements

Media

Compartment

Tear Bar

Platen Surface

Figure 15: MZ Series Cleaning

Note • Twelve packs of approved cleaning pens are available from Zebra as p/n AN11209-1.

Caution • To avoid possible personal injury or damage to the Printer, never insert any pointed or sharp objects into the Printer.

continued

MZ Series User Guide

Troubleshooting

Interpreting Indicators

The printer’s indicators display various printer functions and their status. Check the indicator status, then refer to the

Troubleshooting topic referenced in the chart.

Function

Indicator

Color

Indicator Status:

Steady

Indicator Status:

Blinking

Troubleshooting

Topic

Power

Charger

Green

Amber/

Green

Indicates printer is on and battery condition is OK to use.

Off indicates battery is not charging. Amber indicates battery is charging. Green indicates battery is charged.

Blinking signiﬁes Low

Battery

N/A

1,6,10

Error Amber

Off indicates no error condition

No media or media door is open.

Application may be missing or corrupted

D a t a i s b e i n g r e ceived

2,4,7,9

Communications

Blue

Cable/IrDA: N/A

Bluetooth: Printer has paired with another Bluetooth device.

802.11b/g: Radio is associated with a

WLAN

D a t a i s b e i n g r e ceived

Radio is trying to associate with a WLAN.

5,8

Troubleshooting Topics

1. No power:

• Ensure you press and hold the Power switch until the

Power light comes on.

• Check that battery is installed properly.

• Recharge or replace battery as necessary.

2. Media does not feed:

• Be sure Media Cover is closed and latched.

• Check media compartment. Ensure media is not binding on the sides of the compartment.

3. Poor or faded print

• Clean printhead.

• Check battery for possible damage. Recharge or replace as necessary.

• Check quality of media.

• If using label media, ensure the “Tone” setting is set to 50.

MZ Series User Guide

4. Partial or missing print:

• Check media alignment.

• Clean printhead.

• Ensure Media Cover is properly closed and latched.

5. No print:

• Replace battery.

• Check cable to terminal.

• (Wireless units only) Restore wireless connection.

6. Reduced battery life:

• Check battery date code — if battery is one to two years old, short life may be due to normal aging.

• Recharge or replace battery.

7. Flashing Amber indicator:

• Check that media is loaded and that printhead is closed and

securely latched.

• If media is present and latch is closed, indicates that no application is present or application is corrupted. Program must be re-loaded.

8. Communication Error:

• (Wireless units only) Check that media is loaded, head is closed and blue communication link light is on.

•(USB) Replace cable to terminal.

9. Label Jam:

• Open media cover.

• Generously apply alcohol to Printer in area of jammed label.

10. Battery Pack Is Hard to Install

• Do not force the battery into place. Verify you have not pinched any wires between the battery and the printer.

• Verify you are plugging the battery connector into the printer correctly.

Resetting an MZ Series Printer

If the printer has locked up and is not responding to any operator inputs or external commands, either from a connected terminal or from a linked LAN, you can perform a forced reset as follows:

1. Open the media compartment and remove any media.

2. Press the Feed button and hold it approximately ten seconds until the

Power, Communications and Error indicators turn off and stay off.

3. After the three indicators turn off, reload the media and close the media compartment cover.

4. Wait at least ten more seconds and press the Power button. The Printer will restart and normal operation can resume.

MZ Series User Guide

Troubleshooting Tests

Printing a Conﬁguration Label

To print out a listing of the printer’s current conﬁguration follow these steps:

1. Turn the printer off. Load the media compartment with journal media (media with no black bars printed on the back)

2. Press and hold the Feed Button.

3. Press and release the Power button and keep the Feed button pressed. When printing starts, release the Feed button.

Refer to Figures 16 and 16a for a sample conﬁguration printout.

Communications Diagnostics

If there is a problem transferring data between the computer and the printer, try putting the printer in the Communications

Diagnostics Mode (also referred to as the “DUMP” mode). The printer will print the ASCII characters and their text representation (or the period ‘.’, if not a printable character) for any data received from the host computer

To enter Communications Diagnostics Mode:

1. Print a conﬁguration label as described above.

2. At the end of 2nd diagnostics report, the printer will print:

“Press FEED key to enter DUMP mode”.

3. Press the FEED key. The printer will print: “Entering

DUMP mode”.

Note • If the FEED key is not pressed within 3 seconds, the printer will print “DUMP mode not entered” and will resume normal operation.

4. At this point, the printer is in DUMP mode and will print the ASCII hex codes of any data sent to it, and their text representation (or “.” if not a printable character).

Additionally, a ﬁle with a “.dmp” extension containing the

ASCII information will be created and stored in the printer’s memory. It can be viewed, “cloned” or deleted using the Label

Vista application. (Refer the Label Vista documentation for more information.)

MZ Series User Guide

To terminate the Communications Diagnostics Mode and return the printer to normal operations:

1. Turn the printer OFF.

2. Wait 5 seconds.

3. Turn the printer ON.

Calling Technical Support

If the printer fails to print the conﬁguration label, or you encounter problems not covered in the Troubleshooting Guide, contact Zebra Technical Support. Technical Support addresses and phone numbers for your area can be found in

Appendix D of this manual. You will need to supply the following information:

• Model number and type (e.g. MZ 220)

• Unit serial number (Found on the large label on the back of the printer, also found in the conﬁguration label printout. Refer to Figures 23 and 24)

• Product Conﬁguration Code (PCC) (15 digit number found on the label on the back of the unit)

MZ Series User Guide

Print Head Test

End of First

Report

Unit Serial

Number

Application

Number

Report appears only on units with wireless options installed.

Units with no wireless options will print an empty line and resume

This example has a

Bluetooth™ radio installed.

Figure 16: Conﬁguration Label Example (MZ 220 illustrated)

MZ Series User Guide

Bluetooth radio parameters

Flash

Memory

Size

Maximum

Label Size

Figure16a: Conﬁguration Label Example (continued)

MZ Series User Guide continued

Figure 16c: Conﬁguration Label Example (continued)

MZ Series User Guide

Resident Fonts

Amount of

Memory

Available

CCL (CPCL) programming language is supported

Speciﬁcations

Note.- Printer speciﬁcations are subject to change without notice.

Printing Speciﬁcations

Print Width

Print Speed (max)

Print Speed (normal)

Print Head Life, calculated

Print Density

Printhead Burn

Line to Tear Edge

MZ 220

Up to 1.89 in. (48,0 mm)

MZ 320

Up to 2.9 in. (71,2 mm)

3” per second (76,2 mm/second)

2” per second (5.0 mm/second)

1 x 10

in. (25.4 Km) nominal

203 dots/inch (8 dots/mm)

0.2 in. (5,08 mm)

Memory and Communications Speciﬁcations, MZ series

Flash Memory

SRAM

Standard

Communications

Optional Wireless

Communications

4 MB

8 MB

USB 2.0 Full Speed Interface (12 Mbps)

& Infrared wireless link (meets IrDA 1.1 communications speciﬁcations )

Optional Bluetooth compatible module

Optional 802.11b/g SRRF module

Only one wireless option may be installed in a printer.

Media Speciﬁcations

Width

MZ 220

2.0 ± .03 in.

(50,8 ±0.8 mm)

MZ 320

3.0 ± .03 in.

(76,2 mm ±0.8 mm)

Max.

Printable

Area

Width

Length

1.9” (48,3 mm) 2.9” (73,7 mm)

Maximum length will vary with the size of loaded applications.

Refer to the conﬁguration label for actual maximum label size.

Label Thickness

Max. Media Roll dia.

Label Inner Core

Diameter

.002 in to .004 in (0,050 mm to 0,102 mm)

1.88 in. (47,8 mm) O.D.

0.40 to 0.75 in.. (10,2 to 19 mm)

Use Zebra brand direct thermal or UV resistant coated media that is outside wound. Refer to Appendix

“B” for more details.

MZ Series User Guide

Font and Bar Code Speciﬁcations for MZ Series

Linear &

2-D Bar

Bar Codes

Available

Rotation

Angles

Fonts

Available

Codabar (NW-7)

UCC/EAN 128

Code 39

Code 93

EAN 8/JAN 8, 2 and 5 digit extensions

EAN 13/JAN 13, 2 and 5 digit extensions

EAN 14/JAN 14, 2 and 5 digit extensions lnterleaved 2 of 5

MSI/Plessey

FIM/POSTNET

UPC-A, 2 and 5 digit extensions

UPC-E, 2 and 5 digit extensions

QR Code

MaxiCode

PDF 417

RSS (Reduced Space Symbology ® )

Composite Symbology

0°, 90°, 180°, and 270°

Standard Fonts: 25 bit-mapped fonts; 1 scalable (CG Trimvirate Bold Condensed*)

Downloadable optional bit-mapped & scalable fonts via Label Vista software

International character sets:

Chinese 16 x 16 (trad.), 16 x 16 (simpliﬁed),

24 x 24 (simpliﬁed);

Japanese 16 x 16, 24 x 24

Korean Myang 16 x 16

Greek

Hebrew/Arabic

*Contains UFST from Agfa Monotype Corporation

MZ Series User Guide

USB Communications Port

Pin#

Signal Name Type

VBUS

USB -

bi-directional

USB +

USB_ID

Return bi-directional

Description

USB Bus Power

I/O signals

Identiﬁes A/B connector

Ground

Figure 17: USB Communications Port

Physical, Environmental and Electrical Speciﬁcations

MZ 220 MZ 320

Weight w/ battery, excluding media

.70 lbs.

(317,5 g. )

.75 lbs.

(340,2 kg.)

Temperature

Relative

Humidity

Battery

Operating : 14° to 122° F (-10° to

50° C)

Charging: 32° to 104° F (-0° to 40° C)

Storage w/o battery: -4° to 140° F

(-25° to 60° C)

Storage w/ battery: -4° to 113° F

(-25° to 45°C)

Operating: 10% to 90% (noncondensing)

Storage: 10% to 90% (noncondensing)

Lithium-Ion, 7.4 VDC (nominal);

1500 mAHr.

Printer Input

Power

Ingression

Protection (IP)

Rating

12.0 VDC; 1.25A

42 continued

MZ Series User Guide

2.47”

(62,7 mm)

3.18” (80,7 mm)

Figure 18: MZ 220 Overall Dimensions

2.26”

(57,4 mm)

2.47”

(62,7 mm)

4.11” (104,4 mm)

Figure 19: MZ 320 Overall Dimensions

MZ Series User Guide

2.26”

(57,4 mm)

MZ Series Accessories

Description

Adjustable shoulder strap

Protective soft case

Vehicle Adapter Cable

Extra battery packs

MZ Series Quad Power

Station

100-240 VAC

MZ 220

•

MZ 320

•

Refer to Appendix A for information on Data I/O Cables

For more details on available accessories, contact your authorized

Zebra re-seller.

MZ Series User Guide

Appendix A

Interface Cables

USB Cable

Part Number AT17010-1; USB A to USB Mini B Cable

MORE INTERFACE CABLES

Contact the Factory or your Zebra Sales Representative for more information on interface cables to most major manufacturer’s data terminals.

You may also visit the Zebra Web site at

http://www.zebra.com

for a listing of interface cables for all series of Zebra mobile printers

MZ Series User Guide Appendices

Appendix B

Media Supplies

To insure maximum printer life and consistent print quality and performance for your individual application, it is recommended that only media produced by Zebra be used.

Advantages include:

• Consistent quality and reliability of media products.

• Large range of stocked and standard formats.

• In-house custom format design service.

• Large production capacity which services the needs of many large and small media consumers including major retail chains world wide.

• Media products that meet or exceed industry standards.

MZ Series Media

Z-Select 4000D 3.2 mil Receipt

Width x Length Part #

2.00” (50,8 mm) x Cont.

3.00” (76,2 mm) x Cont.

Z-Select 1000D 2.4 mil Receipt

LD-D2KV5E

LD-D3KV5B

Width x Length

2.00” (50,8 mm) x Cont.

3.00” (76,2 mm) x Cont.

Part #

LD-D2PX5E

LD-D3PX5B

Length

48’ (14,63 M)

Length

66.7’ (20,3 M)

66.7’ (20,3 M

Rolls/Carton

Wt/Carton

9 lbs.

13 lbs.

Wt/Carton

9 lbs.

13 lbs.

For more information call Zebra Technologies Corporation at

+1.866.230.9495 (U.S., Canada and Mexico) and ask to speak to a Media Sales Representative.

Appendix C

Maintenance Supplies

In addition to using quality media provided by Zebra, it is recommended that the printer be cleaned as prescribed in the maintenance section. The following items are available for this purpose:

• Cleaning Pen (10 pack), Reorder No. AN11209-1

• Cleaning Kit with Cleaning Pen, and Cotton Swabs,

Reorder No. AT702-1

MZ Series User Guide Appendices

Appendix D

Battery Disposal

The EPA certiﬁed RBRC

Battery Recycling

Seal on the Lithium-Ion (Li-ion) battery supplied with your printer indicates Zebra

Technologies Corporation is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful life, when taken out of service in the United States or Canada.

The RBRC program provides a convenient alternative to placing used Li-ion batteries into the trash or the municipal waste stream, which may be illegal in your area.

Important • When the battery is worn out, insulate the terminals with tape before disposal

Please call 1-800-8-BATTERY for information on Li-ion battery recycling and disposal bans/restrictions in your area.

Zebra Technologies Corporation’s involvement in this program is part of our commitment to preserving our environment and conserving our natural resources.

Outside North America, please follow local battery recycling guidelines.

Product Disposal

Do not dispose of this product in unsorted municipal waste. This product is recyclable.

Please recycle according to your local standards. For more information, please see our web site at: http://www.zebra.com/recycle.

MZ Series User Guide Appendices

Appendix E

Product Support

When calling with a speciﬁc problem regarding your printer, please have the following information on hand:

• Model number/type (e.g. MZ 220)

• Unit serial number

• Product Conﬁguration Code (PCC)

For Product Support Contacts, see the table at right or contact your local re-seller.

MZ Series Serial Number Label

MZ 220 illustrated

Serial

Number

Bar Code

PCC

Bar Code

MZ Series User Guide Appendices

Product Support Contacts

In the Americas contact

Regional Headquarters

Zebra Technologies International,LLC

333 Corporate Woods Parkway

Vernon Hills, Illinois 60061.3109 U.S.A

T: +1 847 793 2600

Toll-free +1 800 423 0422

Technical Support

T: +1 847 913 2259

F: +1 847 913 2578

Hardware: [email protected]

Software: [email protected]

In Europe, Africa, the Middle East, and India contact

Regional Headquarters

Zebra Technologies Europe Limited

Zebra House

The Valley Centre, Gordon Road

High Wycombe

Buckinghamshire HP13 6EQ, UK

T: +44 (0)1494 472872

F: +44 (0) 1494 450103

Technical Support

Self Service Knowledgebase:

www.zebra.com/knowledgebase

Email Back Technical Library:

Send email to: [email protected]

Subject: Emaillist

On-Line case registration:

www.zebra.com/techrequest

Customer Service Dept.

For printers, parts, media, and ribbon, please call your distributor, or contact us.

T: +1 866 230 9494

F: +1 847 913 8766

E: [email protected]

Internal Sales Dept.

For printers, parts, media, and ribbon, please call your distributor, or contact us.

T: +44 (0) 1494 768316

F: +44 (0) 1494 768244

E: [email protected]

In the Asia Paciﬁc region contact

Regional Headquarters

Zebra Technologies Asia Paciﬁc, LLC

16 New Industrial Road

#05-03 Hudson TechnoCentre

Singapore 536204

T: +65 6858 0722

F: +65 6885 0838

Technical Support

T: +65 6858 0722

F: +65 6885 0838

E: tsasiapaciﬁ[email protected]

Customer Service

For printers, parts, media, and ribbon, please call your distributor, or contact us.

T: +65 6858 0722

F: +65 6885 0837

MZ Series User Guide Appendices

Appendix F

Using zebra.com

The following details using the search functions on Zebra’s

Web site www.zebra.com for ﬁnding speciﬁc documents .

Finding Manuals:

http://www.zebra.com/id/zebra/na/en/index/resource_library/manuals.html

Select printer model (e.g.

MZ 220)

Select language

Select manual type

Click on“SUBMIT”

Example: FInd the Mobile Printer WIreless Conﬁguration Guide.

Perform the above step and select as a manual type “Networking Manual”

Finding the Label Vista Download page:

http://www.zebra.com/id/zebra/na/en/index/drivers_downloads.html

Sort by

“Manual Type”

(optional step)

Select the Wireless

Conﬁguration Guide

Click on

“Download” to save a .pdf ﬁle to your local drive continued

MZ Series User Guide Appendices

At the resulting window select your printer model from the pull-down menu in the “Utilities” section.

MZ 220

Enter your printer model number and click on “SUBMIT”

Click on

“Download” to save a demo application to your local drive

MZ Series User Guide Appendices

Index

Accessories

MZ Series Charger Power Supply 12

using Quad Power Station 13

Battery, installing 10

Battery life, tips for extending 29

Bluetooth™ Networking Overview 22

Bluetooth Device Address (BDA) 22

Cleaning

general instructions 30

Communications

infrared (IR) 21

USB

Connector signals 41

with a cable 20

Communications diagnostics 34

Conﬁguration Label

printing 34

to determine maximum label size 37,39

Damage, shipping 8

Declaration of Conformity

EU countries

Bluetooth radio 24

Zebra 802.11g WLAN 25

Label Vista 23

use in troubleshooting 34

Manual

CPCL Programming 8,23

Media, loading 15

Operator Controls 17

Programming language

CPCL 8

Radio options.See Wireless communications

Regulatory Information

Bluetooth radio ( MZ-ZBR3) 24

Zebra 802.11b/g Radio 25

Safety Precautions

placement of charger 14 while charging batterys 14

Software 23

MZ Series User Guide

Speciﬁcations

Font/bar Code 40

Memory/communications 39

Physical 41

printing 39

Technical Support, contacting 35

Troubleshooting

Communications Diagnostics Mode 34

control panel indicators 32

Standard control panel indicators

Troubleshooting tests 34 printing a conﬁguration label 19,34

QL conﬁguration label example 36

Troubleshooting Topics ,32

Wireless communications

Bluetooth™ radio 22

Infrared (IrDA) 21

Local Area Network

Zebra 802.11b/g WLAN Radio 25

WLAN Overview 23

Speciﬁcations

Font/bar Code 40

Memory/communications 39

Physical 41

printing 39

Technical Support, contacting 35

Troubleshooting

Communications Diagnostics Mode 34

control panel indicators 32

Standard control panel indicators

Troubleshooting tests 34 printing a conﬁguration label 19,34

QL conﬁguration label example 36

Troubleshooting Topics ,32

Wireless communications

Bluetooth™ radio 22

Infrared (IrDA) 21

Local Area Network

Zebra 802.11b/g WLAN Radio 25

WLAN Overview 23

Patent Numbers

4,673,805

4,736,095

4,758,717

4,816,660

4,845,350

4,896,026

4,897,532

4,923,281

4,933,538

4,992,717

5,015,833

5,017,765

5,021,641

5,029,183

This product and/or its use may be covered by one or more of the following US patents and corresponding international patents worldwide

D275,286

D347,021

D389,178

D430,199

D433,702

3,964,673

4,019,676

4,044,946

4,360,798

4,369,361

4,387,297

4,460,120

4,496,831

4,593,186

4,607,156

5,047,617

5,103,461

5,113,445

5,140,144

5,132,709

5,142,550

5,149,950

5,157,687

5,168,148

5,168,149

5,180,904

5,229,591

5,230,088

5,235,167

5,243,655

5,247,162

5,250,791

5,250,792

5,262,627

5,267,800

5,280,163

5,280,164

5,280,498

5,304,786

5,304,788

5,321,246

5,335,170

5,364,133

5,367,151

5,372,439

5,373,148

5,378,882

5,396,053

5,396,055

5,399,846

5,408,081

5,410,139

5,410,140

5,412,198

5,415,482

5,418,812

5,420,411

5,436,440

5,444,231

5,449,891

5,449,893

5,468,949

5,479,000

5,479,002

5,479,441

5,486,057

5,503,483

5,504,322

5,528,621

5,532,469

5,543,610

5,545,889

5,552,592

5,570,123

5,578,810

5,589,680

5,612,531

5,642,666

5,657,066

5,768,991

5,790,162

5,791,796

5,806,993

5,813,343

5,816,718

5,820,279

5,848,848

5,860,753

5,872,585

5,874,980

5,909,233

5,976,720

5,978,004

5,995,128

5,997,193

6,004,053

6,010,257

6,020,906

6,034,708

6,036,383

6,057,870

6,068,415

6,095,704

6,109,801

6,123,471

6,147,767

6,151,037

6,201,255 B1

6,231,253 B1

6,261,009

6,261,013

6,267,521

6,270,072 B1

6,285,845 B1

6,292,595

6,296,032

6,364,550

6,379,058 B1

6,409,401 B1

6,411,397 B1

6,428,227 B2

6,530,705

6,540,122

6,607,316

6,609,844

6,874,958

6,899,477

MZ Series User Guide

Annonce

Table of Contents

Proprietary Statements

Document Conventions

Introduction to the MZ Series

Unpacking and Inspection

Reporting Damage

Getting Ready to Print

Battery

Installing the Battery

Charging the Battery

MZ Series Quad Power Station

Battery Safety

Charger Safety

Loading the Media (All models)

Operator Controls

Verify the Printer Is Working

Printing a Conﬁguration Label

Connecting the Printer

Cable Communication

IR Communications

Wireless Communications with Bluetooth™

Bluetooth Networking Overview

WLAN Overview

Setting Up the Software

Radio Regulatory Information

Zebra Bluetooth Radios MZ-ZBR3

European Regulatory Information for this Radio

WLAN Module Using 802.11b/g Radio

European Regulatory Information for this Radio

Wearing the Printer

Belt Clip

Adjustable Shoulder Strap

Preventive Maintenance

Extending Battery Life

General Cleaning Instructions

Troubleshooting

Interpreting Indicators

Troubleshooting Topics

Resetting an MZ Series Printer

Troubleshooting Tests

Printing a Conﬁguration Label

Communications Diagnostics

Calling Technical Support

Speciﬁcations

Printing Speciﬁcations

Memory and Communications Speciﬁcations, MZ series

Media Speciﬁcations

Font and Bar Code Speciﬁcations for MZ Series

USB Communications Port

Physical, Environmental and Electrical Speciﬁcations

MZ Series Accessories

•

•

•

•

•

•

•

•

•

•

Appendix A

Interface Cables

USB Cable

Appendix B

Media Supplies

MZ Series Media

Appendix C

Maintenance Supplies

Appendix D

Battery Disposal

Product Disposal

Appendix E

Product Support

Product Support Contacts

Appendix F

Using zebra.com

Index

Patent Numbers

Relaterede