advertisement
![Epson EasyMP Network Projection Operation Guide | Manualzz Epson EasyMP Network Projection Operation Guide | Manualzz](http://s1.manualzz.com/store/data/000785696_1-e5040565db1b2d3ea9f06bc74b96b325-360x466.png)
EasyMP Network Projection Operation Guide
Contents
2
About EasyMP Network Projection
Functions of EasyMP Network Projection . . . . . . . . . . . . . . . . . . . . . 5
Connecting the Computer and Projector
Two Connection Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Connecting to a Projector on a Network and Projecting . . . . . . . 11
Security dialog displayed when connecting . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Connecting to a Projector on a Different Subnet . . . . . . . . . . . . . . 17
Specifying Either an IP Address or Projector Name and Performing a Search
(Advanced Connection Mode Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Various Projection Styles
Projecting Only a PowerPoint Slide Show (Presentation Mode)
Projecting Movies on a Computer (Movie Sending Mode) . . . . . 24
Using Multi-Screen Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Procedure Before Using the Multi-screen Display Function . . . . . . . . . . . . . . . . . 27
Enable the virtual display driver (Windows only) . . . . . . . . . . . . . . . . . . . . . . 27
Appendix
Uninstalling the Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Connection Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
When Using Windows Vista or Windows 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Limitations when projecting from Windows Photo Gallery or Windows Live Photo
Limitations when projecting from Windows Media Center . . . . . . . . . . . . . . . . 41
Contents
Cannot connect to the projector you want to use. . . . . . . . . . . . . . . . . . . . . . . . 42
Cannot connect the projector and the computer via wireless LAN. . . . . . . . . . . 42
Cannot connect the projector and the computer via wired LAN. . . . . . . . . . . . . 43
Cannot connect the projector and the computer via the network. . . . . . . . . . . 43
Cannot select or change the connection mode. . . . . . . . . . . . . . . . . . . . . . . . 44
The mouse pointer is not displayed on the computer screen. . . . . . . . . . . . . . . 45
No audio from the projector when connecting with EasyMP Network Projection.
When a connection is made using EasyMP Network Projection, a PowerPoint Slide
Error message when starting up EasyMP Network Projection . . . . . . . . . . . . . . 47
3
About EasyMP Network Projection
This chapter describes useful functions for EasyMP Network Projection and how to install the software.
Functions of EasyMP Network Projection
You can use EasyMP Network Projection to project your computer screen from the projector via a network. Sharing the projector over the network allows you to project data from different computers without changing the signal cable. Even if the projector is away from the computer, you can still project data via a network.
5
• Multi-screen display s
"Using Multi-Screen Display" p.26
You can use up to four projectors to project a different image from one computer. This allows you to project data such as a report on a landscape screen.
Various Screen Transfer Functions
You can use the following screen transfer functions.
• Movie Sending Mode (supported models only) s
You can send movie files directly to a projector which allows movies to be played smoothly.
• Presentation Mode s
"Projecting Only a PowerPoint Slide Show (Presentation Mode)" p.23
By using Presentation Mode, you can project only the PowerPoint Slide
Show running on your computer. A black screen is projected when the
Slide Show is not playing. You can start presentations smoothly without projecting unnecessary images.
• Distribution function
The screen being displayed by a computer can be simultaneously displayed by up to four projectors on the same network.
You cannot connect multiple computers to one projector simultaneously.
Installing the Software
You can find EasyMP Network Projection on the EPSON Projector
Software CD-ROM. Install the software on the computer you are using.
Software Requirements
EasyMP Network Projection runs on computers that meet the following requirements.
For Windows
OS Windows 2000 * 1
Windows XP * 2
Windows Vista
Professional 32-bit
Home Edition 32-bit
Tablet PC Edition 32-bit
Ultimate 32-bit
Enterprise 32-bit
Business 32-bit
Home Premium 32-bit
Home Basic 32-bit
Windows 7 Ultimate 32/64-bit
Enterprise 32/64-bit
Professional 32/64-bit
Home Premium 32/64-bit
Home Basic 32-bit
Starter 32-bit
CPU Mobile Pentium III 1.2 GHz or faster
Recommended: Pentium M 1.6 GHz or faster
Amount of Memory 256 MB or more
Recommended: 512 MB or more
Hard Disk Space 20 MB or more
6
Display Resolution of no less than XGA (1024x768) and no higher than WUXGA (1920x1200).
Display color of 16-bit color or greater (approx. 32000 display colors)
* 1 Windows 2000 Service Pack 4 only.
* 2 Except for Windows XP without any service packs installed, and Windows XP
Service Pack 1.
For Mac OS X
OS Mac OS X 10.4.x 32-bit
Mac OS X 10.5.1 or later * 32-bit
Mac OS X 10.6.x 32/64-bit
Mac OS X 10.7.x 32/64-bit
Recommended: Mac OS X 10.4.11/10.5.8/10.6.6/10.7.0
CPU
Hard Disk Space
Display
PowerPC G3 900 MHz or faster
Recommended: CoreDuo 1.83 GHz or faster
Amount of Memory 256 MB or more
Recommended: 512 MB or more
20 MB or more
Resolution of no less than XGA (1024x768) and no higher than WUXGA (1920x1200).
Display color of 16-bit color or greater (approx. 32000 display colors)
* Operation is not guaranteed in Mac OS X 10.5.0 because the Firewall settings are not set correctly when the version is updated.
Installing the Software
Installing
Make sure you check the following points before starting installation.
• Close all running applications before starting installation.
• When the language selected for the installation varies from that of the
OS being used, the screens may not be displayed correctly.
a
For EMP NS Connection users
The name of the software has changed.
Before change: EMP NS Connection
After change: EasyMP Network Projection
When using the same function as EMP NS Connection on the projector, install EasyMP Network Projection after uninstalling EMP
NS Connection. Depending on the model, you may not be able to connect to the projector correctly using EMP NS Connection.
For Windows a
You need administrator authority to install EasyMP Network
Projection.
a b
Turn on your computer.
Insert the EPSON Projector Software CD-ROM into the computer.
The installer starts automatically.
a
If the installer does not start automatically, open the CD-ROM drive from My Computer (or Computer), and then doubleclick InstallNavi.exe or EMP_NSCInst.exe.
c Follow the on-screen instructions to install.
For Mac OS X a b c d
Turn on your computer.
Insert the EPSON Projector Software CD-ROM into the computer.
Double-click the EMP_NPInstaller.mpkg icon in the EPSON window.
Installation starts.
Follow the on-screen instructions to install.
a
You can download the latest version of EasyMP Network Projection from the following Web site.
http://www.epson.com/
7
Connecting the Computer and Projector
This chapter explains how to connect the computer and the projector via a network, and the procedure for projecting images from your computer's screen with the projector.
Two Connection Modes
There are two methods of connecting a computer and the projector via a network by using EasyMP Network Projection.
a • Depending on the projector model, either wired LAN connection or wireless LAN connection may not be available.
• To use the wireless LAN connection, you need the Wireless LAN unit for the projector.
If the Wireless LAN unit is not supplied with your projector, please purchase the optional accessory. See the following manual for details on optional accessories.
s User's Guide
Advanced Connection Mode
Advanced Connection Mode connects to an existing network system.
In Advanced Connection Mode, you can connect the projector and the computer via a LAN access point.
When connecting to a network via Wired LAN, connect the projector to the network hub with a commercially available LAN cable.
Quick Connection Mode
Quick Connection Mode is only available when you install the Wireless
LAN unit in the projector.
In Quick Connection Mode, you can connect the projector and the computer directly using wireless communication. This allows you to project the computer screen without making any complicated network settings.
9
Two Connection Modes
Preparing to Connect
Follow the steps below to connect the computer and the projector via a network using EasyMP Network Projection.
a Install EasyMP Network Projection on the computer to be connected.
s
b Make network settings on the computer and put it into network connection status.
See the documentation supplied with your the computer, LAN adapter, or AirPort card for details on network settings.
a
When the computer you are using is normally connected to the network, you do not need to make network settings on the computer.
c For Quick Connection Mode
Install the Wireless LAN unit to the projector.
For Advanced Connection Mode
Make network settings on the projector and put it into network connection status.
You can make network settings from the projector's Network menu.
See the following manual for details.
s User's Guide
10 d Press the [LAN] button on the remote control.
The LAN standby screen is displayed.
If there is no signal for the current input source, it automatically switches to the LAN source. If it does not automatically switch to the
LAN source, press the [LAN] button.
e Start EasyMP Network Projection on the computer and connect with the projector.
s
"Connecting to a Projector on a Network and Projecting" p.11
a
If a connection error occurs, a number indicating the type of error is displayed as follows.
Event ID: 04xx
See the following manual for details on Event ID.
s User's Guide
Connecting to a Projector on a Network and Projecting
11
Operating the Computer
In the following explanations, unless otherwise noted, Windows screen shots are used. Similar screens are displayed on Mac OS X.
a Start EasyMP Network Projection.
For Windows
Click Start, select Programs (or All Programs), EPSON Projector,
EasyMP Network Projection , and then click EasyMP Network
Projection V2.XX
.
For Mac OS X
Double-click EasyMP Network Projection from the Applications folder.
b Select Quick Connection Mode or Advanced Connection Mode, and then click OK.
s
The projector search results are displayed. To always connect using the selected connection mode, select Set the selected Connection
Mode as the default mode for future connections.
c Select the projector you want to connect to, and then click
Connect.
If the projector you want to connect to is not displayed in the search results, click the Automatic search button. The search takes about 30 seconds.
See the following section for details on the connection screen.
s
"Using the Connection Screen" p.12
d a
When Projector Keyword is set to On from the projector, the keyword entry screen is displayed. Enter the keyword displayed on the LAN standby screen, and then click OK.
When the connection is complete, the computer screen is projected.
The following EasyMP Network Projection toolbar is displayed on the computer screen. You can use this toolbar to operate the projector and make settings, and to disconnect the network connection. See the following section for details on the toolbar.
s
When connecting from another computer, such as when changing presenters, start EasyMP Network Projection from the computer you want to connect. The computer that is currently connected is disconnected, and the projector is then connected with the computer that is trying to connect now.
If a connection is made while Disable interrupt connection is set, the connection is not switched to another computer.
Security dialog displayed when connecting
In Quick Connection Mode, the following dialog box may be displayed when connecting to a projector with security settings enabled.
Connecting to a Projector on a Network and Projecting
For Windows Vista/Windows 7
• Enter the passphrase set on the projector. If you select Save the passphrase and don't show this dialog box again.
the projector's SSID and passphrase are saved on the computer and this dialog box is not displayed the next time you connect. You do not have to enter the passphrase again.
Using the Connection Screen
Start EasyMP Network Projection to display the following screen. The operation of each button or item is described in the following table.
When the system starts in Quick Connection Mode.
12
• The following dialog box is displayed if the projector's passphrase has not been changed from the default. Change the passphrase from the projector's Network menu.
For Windows 2000/XP
You cannot connect to a projector with security settings enabled. Set
Security to Off in the projector's Configuration menu.
Connecting to a Projector on a Network and Projecting
When the system starts in Advanced Connection Mode.
A Automatic search
In Quick Connection Mode, you can search for the projectors based on the SSID.
In Advanced Connection Mode, you can search for available projectors on the network system to which the computer is connected.
Manual search B
In Quick Connection Mode, you can search for the projector based on the SSID selected from a list.
In Advanced Connection Mode, you can search for a projector based on a specified IP address or projector name.
C Status
The following seven icons indicate the status of the detected projectors.
Standby Available.
13
Busy
Busy (Disable interrupt con‐ nection)
Currently in use by another application
Searching
Available. When you click Connect, the computer currently connected is disconnected and your computer is connected.
Cannot be selected. Disable interrupt connection is set on another computer which is already connected.
The projector's Configuration menu is open. You can select it after closing the
Configuration menu and running the search again.
Displayed while running Manual search or
Profile.
Not found.
Displayed when a projector cannot be found as a result of Manual search or Profile.
Not acquired Available. Displayed when a projector with security settings enabled is found in Quick
Connection Mode.
D Projector name
The projector's name is displayed.
E Update list (Quick Connection Mode only)
Updates Status and Signal intensity.
F Disable interrupt connection
Select this to prevent an interrupt connection by other computers while connected to the selected projector.
G Use multi-display
Select this when using the Multi-screen display function. When this is selected,
Display layout and Display properties are displayed at the bottom of the screen.
s
"Using Multi-Screen Display" p.26
H Troubleshooting
If there is a problem and you cannot have a connection, press this button to open the EasyMP Network Projection Troubleshooting screen.
I Connect
Connect to the projector you selected from the search results list. When a connection is made with a projector, a toolbar is displayed.
Connecting to a Projector on a Network and Projecting
14
J Set options
You can make option settings such as the processing method when EasyMP
Network Projection starts.
s
K Save in the profile
Saves the results of a network projector search as a profile.
s
L Clear list
Deletes all search results.
M SSID (Quick Connection Mode only)
The projector's SSID is displayed.
N Signal intensity (Quick Connection Mode only)
As the Signal intensity increases, so does the number of lit indicators.
O Profile
You can search for a projector on the network using a profile saved using
Save in the profile .
s
"Performing a Search with a Profile" p.18
P IP address (Advanced Connection Mode only)
The projector's IP address is displayed.
Q Display
Select the display number (when Use multi-display is selected).
s
"Projecting the Allocated Images" p.32
Using the Toolbar
The toolbar is displayed on the computer screen after EasyMP Network
Projection starts and a connection is made with the projector. You can use this toolbar to operate and make settings for the projector.
Select target projector
Click to limit the projector operated from the toolbar when projecting from multiple projectors using the distribution function or Multiscreen display. The indication below the icon shows the projectors that can be controlled.
ALL indicates that all of the connected projectors can be controlled.
For example, when "1, 3" is displayed, projectors No. 1 and No. 3 can be controlled.
Click to display the following screen.
A Select the projector to be controlled.
B Indicates the No. of an allocated projector. This No. appears under the icon to indicate the No. of the projector that you can control from the toolbar.
C Indicates the status of the projector.
Stop
Stops projection while connected to the projector. A black screen is projected while stopped.
Connecting to a Projector on a Network and Projecting
Show
Releases Stop or Pause.
Pause
Pauses projected images while connecting to the projector.
Presentation Mode
Each time this is clicked, Presentation Mode switches between enabled/ disabled.
s
"Projecting Only a PowerPoint Slide Show (Presentation Mode)" p.23
Projector control
While the projector is connected to the network, the projector's A/V
Mute, Switch PC source and Switch video source functions can be controlled from both the remote control and the projector's control panel.
Click to display the following toolbar.
Screen Preview
A/V Mute
Turns the video and audio on or off.
Switch PC source
Changes to images from the port where the signal is being input.
Switch video source
Changes to images from the video input port.
Displays the multi-screen preview screen.
Click to display a preview with the settings you have made. Click each display to enlarge each Screen Preview to full-screen.
15
Set options
Transmission performance during the transfer of computer images can be adjusted.
s
Movie Sending Mode
Used to immediately playback a movie file. If the projector cannot playback movies, the message "The connected projectors do not support Movie Sending." is displayed.
s
Disconnect
Disconnects the connection to the projector.
Signal intensity (Quick Connection Mode only)
This is displayed when the connection is made in Quick Connection
Mode. As the Signal intensity increases, so does the number of lit indicators.
Switch toolbar display
Connecting to a Projector on a Network and Projecting
The toolbar display is switched as follows. The toolbar display remains as is until switched again.
Full
Normal
Simple
16
Connecting to a Projector on a Different Subnet
17
You can connect the projector and the computer and project to screens at remote locations (on different subnets).
In Automatic search, projectors on different subnets are not found because searches are only performed on the same subnet.
You can use the following methods to connect to a projector on a different subnet.
• Specify either an IP address or projector name and perform a search.
The IP address can be input directly. Also, provided the projector name to be connected has been registered on the DNS server, you can perform a search simply by inputting that projector name.
s
"Specifying Either an IP Address or Projector Name and Performing a
Search (Advanced Connection Mode Only)" p.17
• Perform a search based on a Profile.
Once you have performed a search for a projector on a different subnet by specifying either an IP address or a projector name, you can save the search as a profile with an easy-to-remember name, and then use that profile whenever you subsequently want to search for a projector on a different subnet.
s
"Performing a Search with a Profile" p.18
a • If you cannot find a projector, see the following section for the most likely causes.
s
• When you use Manual search in Quick Connection Mode, you can specify the SSID. When there are a lot of projectors you can narrow the search field by using SSID.
Specifying Either an IP Address or Projector Name and Performing a Search (Advanced Connection
Mode Only)
In the following explanations, unless otherwise noted, Windows screen shots are used.
Similar screens are displayed on Mac OS X.
a Click Manual search on the EasyMP Network Projection projector selection screen.
b Enter the IP address or the projector name for the projector you want to connect to, and click OK.
Connecting to a Projector on a Different Subnet
18 a While the projector is displayed on the EasyMP Network Projection projector selection screen, click Save in the profile.
The search results are displayed on the EasyMP Network Projection projector selection screen.
Provided the target projector has been identified, select that projector, and then click Connect to establish a connection.
Once you have saved projector information as a profile, you do not have to specify the relevant details every time you perform a search.
s
Performing a Search with a Profile
You can save a search for a frequently used projector as a profile. A profile is a file containing all of the information pertaining to a given projector, such as the projector name, its IP address, and SSID. You can specify a profile to search for a projector instead of specifying relevant details such as the IP address and projector name. For example, by creating a group of profiles for each place where a projector is setup and managing them with folders, the target projector can be found quickly.
This section explains how to create, edit, and manage a profile.
Making a Profile
Profiles are made by saving search results.
For details on how to edit a previously saved profile, see the following section.
s
The Save in the profile screen is displayed.
b Enter a Profile name, and then click Add.
Projector information is registered in the profile.
If you have previously saved a profile, you are prompted to confirm whether or not to overwrite. To save a profile with a different name, select Save as. If you have created a folder for profiles, one of the
Connecting to a Projector on a Different Subnet
19 following screens is displayed. After entering the Profile name and selecting the Save in destination, click Add.
For Windows
Searching by specifying a Profile
You can search by specifying the profile you created.
a Click Profile on the EasyMP Network Projection projector selection screen.
If no profile is registered, you cannot select Profile.
For Mac OS X a
For details on how to create a folder for profiles, see the following section.
s
b From the menu that is displayed, select the projector you want to connect to.
The search results are displayed on the EasyMP Network Projection projector selection screen.
Provided the target projector has been identified, select that projector, and then click Connect to establish a connection.
Connecting to a Projector on a Different Subnet
Managing a Profile
You can change the name and the hierarchical structure of the profile.
a Click Set options on the EasyMP Network Projection main screen.
The Set options screen is displayed.
b Click Edit profile.
The Edit profile screen is displayed.
c Edit the contents registered in the profile.
A
B
Profile
Item
Profile
Copy
Delete
: Indicates a profile.
: Indicates a folder.
Function
You can display the registered profile. You can manage it by creating a folder.
You can copy the profile. The copied profile is saved in the same folder as the original with the same name.
You can delete the profile and the folder.
20
Connecting to a Projector on a Different Subnet
Profile
Item
Rename
Create folder
Export
Function
You can display the Rename dialog box to rename the folder or the profile. You can enter up to 32 characters in the Rename dialog box.
You can create a new folder.
You can export the profile. Exported profiles can be used as backup files. You can import them with another computer.
You can load an exported profile.
Import
Information on selected profile
Item Function
Projector name The projector information registered in the profile is displayed.
SSID or IP address
Delete You can delete the information for the selected projector. When all projector information is deleted, the profile is also deleted.
d Click OK.
Saves your edits and closes the Edit profile screen.
21
Various Projection Styles
This chapter explains the functions that may be useful in a meeting or presentation, such as the Multi-Screen Display which allows you to send images to multiple projectors from a single computer.
Projecting Only a PowerPoint Slide Show (Presentation Mode)
By using Presentation Mode, you can project only the PowerPoint Slide
Show running on your computer. A black screen is projected when the
Slide Show is not playing. You can start presentations smoothly without projecting unnecessary images.
In addition to PowerPoint, Keynote is compatible with Presentation Mode for Mac OS X.
To set Presentation Mode to On or Off, click the s
button.
23
Projecting Movies on a Computer (Movie Sending Mode)
You can send movie files to the projector using Movie Sending Mode. This allows movies to be played more smoothly than by projecting them played with other applications on a computer.
You can also select multiple files and play them repeatedly from first to last.
However, some projectors may not support movie files.
a • You can use Movie Sending Mode to send a movie to a single projector.
Sending a movie to multiple projectors simultaneously is not possible with Movie Sending Mode.
• The image and sound may skip or stop depending on the communication method and electromagnetic wave conditions.
Playing Movies
a Click the button on the toolbar.
The projector selection screen is displayed.
b Select the projector, and then click OK.
The Movie Sending Mode screen is displayed.
c Click Select file.
Supported Files
The following table indicates the specifications for files supported by Movie
Sending Mode.
File Type
(Exten‐ sion)
.mpg
.mpeg
.mp4
.wmv
.asf
Movie Codec
MPEG-2
MPEG-4 ASP
H.264/MPEG-4
AVC
WMV9
Audio Codec
WMA
Recording
Quality
MPEG-1 Layer 1/2
You can play MPEG contents without audio. Linear PCM and
AC-3 are not supported.
MPEG-4
AAC-LC
Maximum frame rate: 30 fps
Maximum reso‐ lution: 1280x720
You cannot project files protected by digital rights management (DRM).
d Select a movie file to play, and then click Open.
24
Projecting Movies on a Computer (Movie Sending Mode)
Pause
Pauses playback.
Stop
Stops playback.
Back
Plays the current file from the beginning.
Next
Plays the next file from the beginning.
Repeat
Plays repeatedly from the first file in the list. You cannot repeat one specific file when there are multiple files in the list.
f Click Close to exit Movie Sending Mode.
25
The Movie Sending Mode screen is displayed again. The selected file is displayed in the Movie file list.
If you click Select file, the Movie file list is updated with items you select later.
e Play and stop the movie file on the Movie Sending Mode screen.
Position indicator
Starts playing the file from the point at which it is dragged and dropped.
Play
Plays the file.
Using Multi-Screen Display
Multi-screen display mode allows you to project different images from multiple projectors that are connected to a single computer.
With Windows, multiple virtual display
drivers can be set in the computer, and each image can be projected by the projector. This function is not available with Windows Vista and Windows 7.
For Mac OS X, an external monitor needs to be connected to the computer to enable this function. While the following explanation refers to virtual display, for Mac OS X the operation relates to the screens displayed on the physically connected monitor.
Example of Adjusting the Virtual Display
By arranging the virtual display
allocation, you can project only the image that you want to show or project different images from left to right in a presentation.
Arrangement example 1
A
B
Actual monitor image PowerPoint file
Image of virtual display Excel file
26
Using Multi-Screen Display
Arrangement example 2
A
B
Actual monitor image PowerPoint file presenter tools
Image of virtual display Slide Show using a PowerPoint file
27
Procedure Before Using the Multi-screen Display
Function
a Set the virtual display.
s
"Setting the Virtual Display" p.27
In a Windows environment, enable the virtual display
driver as necessary. Also, for both Windows and Mac OS X, set up the virtual display arrangement.
b Allocate the image to be projected.
s
"Allocating the Image to be Projected" p.32
Open the file to be projected, and then move the screen to the virtual display according to the actual projection arrangement.
c Project the allocated images.
s
"Projecting the Allocated Images" p.32
Allocate a virtual display number to a projector, and then start projection.
Setting the Virtual Display
This section explains the virtual display for arrangement example 1.
s
"Example of Adjusting the Virtual Display" p.26
Enable the virtual display driver (Windows only)
Enable the virtual display
driver. If you have already enabled the virtual display while installing EasyMP Network Projection, this operation is not necessary. Go to the following section.
s
"Adjusting the Virtual Display" p.28
Using Multi-Screen Display a Click Start, select Programs (or All Programs), EPSON Projector,
EasyMP Network Projection, and then click Add-Remove Virtual
Display.
The Add-Remove Virtual Display screen is displayed.
b Select the virtual display you want to use.
Up to four monitors can be added. In this example, a single virtual display is to be used. When setting multiple virtual displays, select as many displays as necessary.
Any one of the displays can be selected.
c Click OK.
When you click OK, the drivers for the virtual display are enabled.
At this point, it is normal for the display to flicker. Wait for the
Add-Remove Virtual Display screen to close.
Adjusting the Virtual Display
After starting EasyMP Network Projection, the procedure for setting up the virtual displays differs for Windows and Mac OS X. The procedures are explained separately below.
28 a
Check the following points before starting EasyMP Network Projection when connecting via Wireless LAN. If the following points are not set correctly, Multi-screen display cannot be used.
• The SSID for the computer and each projector must be the same.
(For Quick Connection Mode)
• The wireless LAN system for the computer and each projector must be the same.
You can modify the SSID and wireless LAN system for the projector from the projector's Network menu.
See the following manual for details.
s User's Guide
For Windows a Click Start, select Programs (or All Programs), EPSON Projector,
EasyMP Network Projection, and then click EasyMP Network
Projection V2.XX to start EasyMP Network Projection.
b c
Select Quick Connection Mode or Advanced Connection Mode, and then click OK.
Select the Use multi-display check box.
Using Multi-Screen Display e Click the Settings tab.
29 d
Display layout and Display properties are added at the bottom of the screen.
Click Display properties.
f Drag the displayed monitor icon and place it where desired.
Here, the actual monitor (1) is placed on the left, while the virtual monitor (3) is placed on the right.
When the PC has multiple display output terminals, the numbers assigned to the virtual terminals will be sequential to those of the physical terminals.
The Display Properties screen is displayed.
Using Multi-Screen Display
30 g Click OK to close the Display Properties screen.
Allocate the projecting images next.
s
"Allocating the Image to be Projected" p.32
For Mac OS X a Double-click EasyMP Network Projection from the Applications folder to start EasyMP Network Projection.
b c
Select Quick Connection Mode or Advanced Connection Mode, and then click OK.
Select the Use multi-display check box.
a • When an external monitor is connected as a secondary monitor, the image for that screen cannot be projected.
• Depending on the hardware, the number of the secondary monitor may be other than "2". When placing the monitor icons, click the icon to check that the display monitor type is not the secondary monitor.
• For the Screen Resolution settings, see the following.
s
When the monitor icon is arranged, a virtual display is connected as the image like below.
d
Display layout and Display preferences are added at the bottom of the screen.
Click Display preferences.
Using Multi-Screen Display e
The display setting screen is displayed.
Click Arrangement.
g Drag the displayed monitor icon and place it where desired.
f Clear the Mirror Displays check box.
h Close the display setting screen.
Allocate the projecting images next.
s
"Allocating the Image to be Projected" p.32
31
Using Multi-Screen Display
Allocating the Image to be Projected
This section explains the virtual display for arrangement example 1.
s
"Example of Adjusting the Virtual Display" p.26
a Open the file to be projected.
Open the PowerPoint and Excel files.
b Drag the window to the desired virtual display
monitor, and allocate it where the image is to be projected.
Drag the Excel window to the right until it cannot be seen. The
PowerPoint window appears on the actual monitor, while the Excel window appears on the virtual display on the right.
b Click Connect.
Projecting the Allocated Images
This section explains the virtual display for arrangement example 1.
s
"Example of Adjusting the Virtual Display" p.26
a Select the number of the virtual display
to allocate on the
Display, and set which image to be projected from which projector.
The image allocated to each projector is projected.
32
Using Multi-Screen Display
In a Windows environment, you cannot view the image being sent to a virtual display on the computer. To adjust the image on the virtual display, you must do so while viewing the projected image.
To perform mouse-based operations on the virtual display, move the mouse pointer in the direction of the virtual display so that the pointer appears on the virtual display.
c To end projection for multi-screen display, click Disconnect on the toolbar.
a
In a Windows environment, if the virtual display driver has been enabled so that the mouse pointer can be moved outside the limits of the screen, there may be occasions when you lose track of the location of the pointer. If you are not using a virtual display, clear the virtual display checkbox on the Add-
Remove Virtual Display screen so that the mouse pointer moves back inside the screen's display area. To subsequently use multidisplay again, place a check mark against the required display under Add-Remove Virtual Display.
To clear a check mark, see the following.
s
"Enable the virtual display driver (Windows only)" p.27
33
Appendix
Set options
You can make option settings such as the processing method when EasyMP
Network Projection starts.
Access Set options from the main screen of EasyMP Network Projection.
a Click Set options on the EasyMP Network Projection main screen.
General settings tab
The Set options screen is displayed.
b Set each of the items.
Confirm the details of the set items in the following sections. When you have made all the necessary settings, click OK to close the Set options screen.
a
You can also access Set options by clicking on the toolbar. When you access Set options from toolbar, the General settings tab is not displayed.
Use full-screen video transfer
Encrypt communications
Display Connection
Mode Selection window on startup
Plays back a movie file at full screen. If the projector does not support movie sending, this function cannot be set.
Select to encrypt and transmit data. Even if data is intercepted, it cannot be decrypted.
When using Quick Connection Mode, make sure you always select this checkbox.
Set whether or not the Quick Connection Mode/Advanced
Connection Mode screen is displayed when EasyMP
Network Projection starts.
Clear this checkbox once you have settled on a regular startup method.
35
Set options
36
Make the movement of the mouse pointer smooth
Search method on startup
Wireless LAN passphrase setting files
Edit profile
Switch LAN
Restore Defaults
Windows only (except for Windows 2000)
Select to prevent the mouse pointer from flickering when
Transfer layered window is selected in Adjust performance . (When Windows Aero is selected as the theme in Windows Vista/7, Windows Aero turns off by selecting this setting. )
Select from the following projector search methods executed when EasyMP Network Projection is started.
Automatic search on startup
Specify search method after startup
Search with the last network configuration
Not available for Windows 2000/XP.
In Quick Connection Mode, SSIDs and passphrases are stored on the computer when connecting to a projector with security settings enabled. You can edit and delete the stored information.
Edit : Displays the wireless network management screen for the computer.
Delete all : Deletes all the SSIDs and passphrases stored on the computer.
The Edit profile dialog box is displayed.
s
Windows only
This is used when it is necessary to switch the network adapter to be used for a search when a computer has multiple adapters.
By default, all of the network adapters are used to perform a search.
You can reset all adjustment values for Set options to their default settings. However, you can retain settings for Edit profile and Switch LAN in General settings.
Adjust performance tab
Performance adjustment slider
Lower the resolution and transfer
The performance can be set to Fast, Normal, and
Fine .
Set to Fast when movie projections are interrupted.
Only available for projectors with a resolution of
WUXGA (1920x1200).
Select to reduce the size of the data to be transferred to the projector by lowering the resolution. Use this option on a slow network or when displaying the image takes too long or is interrupted.
Set options
Transfer layered window
Disable Windows
Aero and improve the tracking of the interactive pen
Restore Defaults
Windows only (excluding Windows Vista and
Windows 7).
The layered window is in use when contents such as messages displayed on the computer are not projected by the projector. Select this check box to project contents such as messages that use the layered window.
If the mouse pointer flickers on the screen, select
Make the movement of the mouse pointer smooth in
General settings .
Only available when Windows Aero is selected as the theme.
Select to improve the tracking delay for the interactive pen. Windows Aero is disabled and interactive pen operations become smoother.
You can reset all adjustment values for Set options to their default settings. However, you can retain settings for Edit profile and Switch LAN in General settings .
Audio Output tab
37
Output audio from the projector
Restore Defaults
Select to output the computer's audio from the projector. Clear to output audio from the computer.
However, when playing movies with audio in Movie
Sending Mode, audio is always output from the projector regardless of this setting.
You can reset all adjustment values for Set options to their default settings. However, you can retain settings for Edit profile and Switch LAN in General settings .
Set options a
Audio can only be transferred to one projector. Audio cannot be transferred when connected to multiple projectors.
38
Uninstalling the Software
Make sure you check the following points before starting uninstallation.
• For Windows, you need administrator authority to uninstall EasyMP
Network Projection.
• Close all running applications before starting uninstallation.
For Windows 2000 a b c d
Click Start, select Settings, and then click Control Panel.
Double-click Add/Remove Programs.
Click Change or remove program.
Select EasyMP Network Projection, and then click
Change/Remove.
For Windows XP a b c
Click Start, and then click Control Panel.
Double-click Add or Remove Programs.
Select EasyMP Network Projection, and then click
Change/Remove.
For Windows Vista/Windows 7 a b c
Click Start, and then click Control Panel.
Click Uninstall a program from the Programs category.
Select EasyMP Network Projection, and then click
Uninstall/Change.
For Mac OS X a Open the Applications folder.
39 b Open the EasyMP Network Projection - Tools folder, and then double-click EasyMP Network Projection Uninstaller.app to uninstall the software.
Connection Limitations
40
When projecting computer images while running EasyMP Network
Projection, the following restrictions apply. Confirm these points.
32-bit color
Windows Mac OS X
About 16.7 million colors (32-bit)
The operational guarantee for multi-screen display is 16-bit and 32-bit color.
Supported Resolutions
The following computer screen resolutions can be projected. You cannot connect to a computer whose resolution is greater than WUXGA
• VGA
• SVGA
• XGA
• SXGA
(1024x768)
*
*
(1280x960)
• SXGA (1280x1024) *
• SXGA+ (1400x1050) *
• WXGA (1280x768) *
• WXGA (1280x800) *
• WXGA+ (1440x900) *
• UXGA (1600x1200)
• WUXGA (1920x1200)
* Supported resolutions when multi-screen display function is on.
When using a computer screen with a unique aspect ratio, depending on the resolution of the computer and the projector, the resolution is increased or decreased so as not to impair the image quality.
Depending on the resolution, at times the vertical or horizontal margins may be projected in black.
Display Color
The number of colors for computer screens that can be projected.
16-bit color
Windows Mac OS X
About 32,000 colors (16-bit)
Other Limitations
• If the transmission speed of the wireless LAN is low, the network might be cut off unexpectedly.
• Applications that use part of DirectX functions may not be displayed correctly. (Windows only)
• Cannot project full screen MS-DOS prompts. (Windows only)
• There are times when the image on the computer screen and the image projected by the projector may not match exactly.
• Movies are not played as smoothly as they are on a computer.
When Using Windows Vista or Windows 7
Note the following points when using EasyMP Network Projection on a computer running Windows Vista or Windows 7.
Limitations when projecting from Windows Photo Gallery or
Windows Live Photo Gallery
Note the following two limitations when launching Windows Photo Gallery or Windows Live Photo Gallery when EasyMP Network Projection is running.
Connection Limitations
41
• Slideshow is played back in simple mode when projecting from
Windows Photo Gallery or Windows Live Photo Gallery.
Because the toolbar is not displayed, you cannot change the Theme
(effects) while playing a slide show, regardless of the Windows Experience
Index rating.
Once simple mode has started, you cannot change modes while Windows
Photo Gallery or Windows Live Photo Gallery is running even if you close EasyMP Network Projection. Restart Windows Photo Gallery or
Windows Live Photo Gallery.
• You cannot play movies.
• A few minutes after you connect a computer to the projector over a network with EasyMP Network Projection, the following message may be displayed.
It is recommended that you select Keep the current color scheme, and don't show this message again . This selection is enabled until the computer is restarted.
Limitations in Windows Aero
Note the following two limitations when the window design for your computer is Windows Aero.
• The layered window is projected regardless of Transfer layered window from Set options in EasyMP Network Projection.
For example, when Transfer layered window for the EasyMP Network
Projection toolbar is disabled, it is not projected even if it is displayed on the computer screen, however the toolbar is projected.
Limitations when projecting from Windows Media Center
You cannot project images in full screen display using Windows Media
Center. Switch to the window display mode to project the images.
Troubleshooting
Cannot connect to the projector you want to use.
Cannot connect the projector and the computer via wireless LAN.
Check
Is the Wireless LAN unit connected?
Is the SSID the same as that of the access point?
(For Quick Connection Mode)
Is the DHCP function for Wired LAN turned On?
(For Quick Connection Mode)
Remedy
Check that the Wireless LAN unit is securely connected.
Set an SSID that is different from that of the access point.
You can make the SSID setting from the projector's Network menu.
See the following manual for details.
s User's Guide
Set the DHCP setting to Off from Wired LAN in the Configuration menu.
See the following manual for details.
s User's Guide
Check that the wireless LAN adaptor or wireless LAN card is installed on the computer.
Enable the wireless LAN.
Is the computer's wireless LAN function working?
Is the wireless LAN setting enabled when the computer is in power save mode?
Are there any obstacles between the access point and the computer or projector?
Is the computer's wireless LAN radio strength set to low?
Sometimes the indoor environment prevents the projector from being found in a search. Check for any obstacles between the access point and the computer or projector, and change their position to improve communication.
Set the radio strength to maximum.
Does the wireless LAN system meet the supported specifications? Check the wireless LAN system. See the following manual for details on the projector's wireless LAN system.
s User's Guide
Is the Wireless LAN Power set to Off in the projector's
Configuration menu?
Set Wireless LAN Power to On in the Wireless LAN menu from the Configuration menu.
See the following manual for details on the projector's wireless LAN settings.
s User's Guide
Is the AirPort setting for Mac OS X correct?
Check that AirPort is set to on. Or, check whether an appropriate access point has been selected.
Is the same WEP key set?
When selecting WEP from Security, set the access point, the computer, and the projector to the same WEP key.
See the following manual for details on the WEP key.
s User's Guide
42
Troubleshooting
43
Cannot connect the projector and the computer via wired LAN.
Check
Are the computer's LAN card and the built-in LAN function available?
Is the network cable connected correctly?
Remedy
Check that LAN is available from the device manager under Control Panel - System - Hardware.
Check that the network cable is connected correctly. Reconnect it if it is not connected or not connected properly.
Cannot connect the projector and the computer via the network.
Check Remedy
Is the network configuration screen displayed on the projector?
Close network settings on the projector, and return to the LAN standby screen. If the network configuration screen is displayed on the projector, you cannot connect using EasyMP Network Projection.
Was the network adapter used selected correctly with EasyMP
Network Projection?
Is the firewall turned off, or has the firewall been registered as an exception?
If the computer has multiple LAN environments, it cannot connect unless the network adapter is selected correctly.
When using a computer running Windows, start EasyMP Network Projection and select the network adapter you are using from Set options - Switch LAN.
s
When you do not wish to turn off the firewall or register the firewall as an exception, make the necessary settings to open the ports.
The ports used by EasyMP Network Projection are "3620", "3621", and "3629".
Is the SSID setting different?
(For Advanced Connection Mode)
Are the connection denial functions, such as MAC Address restrictions and port restrictions, set correctly at the access point?
(For Advanced Connection Mode)
Set the computer, the access point, and the projector to the same SSID.
You can make the SSID setting from the projector's Network menu.
See the following manual for details.
s User's Guide
Set connection permission at the access point to allow projectors to connect.
Are the IP address, the subnet mask, and the gateway address for the access point and the projector set correctly?
(For Advanced Connection Mode)
When not using a DHCP, adjust each setting.
You can make the DHCP setting from the projector's Network menu.
See the following manual for details.
s User's Guide
Troubleshooting
44
Check
Are the access point and the projector's subnet different?
(For Advanced Connection Mode)
Have you enabled DHCP?
(For Advanced Connection Mode)
Remedy
Select Manual search from EasyMP Network Projection, specify the IP address, and connect.
s
"Specifying Either an IP Address or Projector Name and Performing a Search (Advanced Connection Mode
When DHCP is set to On in Advanced Connection Mode, it may take some time to enter LAN standby status if an available DHCP server is not found.
When a connection is made using EasyMP Network Projection, the projected image remains as it is, and a connection cannot be made from another computer.
Check
Did the presenter leave the conference room without cutting off the network connection?
Remedy
With EasyMP Network Projection, the computer currently connected can be disconnected when another computer tries to connect to the projector.
Therefore, when a Projector Keyword is not set for the projector, or if you know the Projector Keyword, you can disconnect the computer currently connected and then connect your computer to the projector.
When a Projector Keyword is set for the projector and you do not know the Projector Keyword, restart the projector and reconnect.
Cannot select or change the connection mode.
Check
Is EasyMP Network Projection set to start up using the same connection mode?
Remedy
Select Display Connection Mode Selection window on startup on the General settings tab from Set options. The projector selection screen is displayed after restarting EasyMP Network Projection.
The screen is not projected.
The Slide Show cannot be displayed on the desired display when the multi-screen display function is being executed.
Check
Are you using PowerPoint 2002 or an earlier version?
(For Windows)
Remedy
To set and use two or more virtual displays g
, use PowerPoint 2003 or later, or limit the number of virtual displays to one before displaying the Slide Show.
Troubleshooting
45
Applications are no longer displayed from the computer screen when the multi-screen display function is executed.
Check
Is another application running on the virtual display g ?
(For Windows)
Remedy
When Virtual Display is installed, another application sometimes runs on the virtual display. In this case, set Virtual
Display to off in Screen properties.
The mouse pointer is not displayed on the computer screen.
Is Virtual Display installed?
(For Windows)
Check Remedy
The mouse pointer was moved onto the virtual display
g . When the virtual display checkbox is cleared on the Add-
Remove Virtual Display screen, the mouse pointer returns to the screen display area.
The mouse pointer flickers.
Check
Is Make the movement of the mouse pointer smooth selected?
Is Transfer layered window selected?
Remedy
Do one of the following to stop the mouse pointer from flickering on the screen.
• Select Make the movement of the mouse pointer smooth.
s
• Clear the Transfer layered window check box.
s
When connecting with EasyMP Network Projection the image is not displayed or the image is slow to appear.
Check
Did you try to playback movies with Media Player or try to operate the screen saver preview?
Depending on the computer, the movie playback screen in Media Player may not be displayed, and the screen saver preview may not be displayed normally.
Remedy
Is WEP encryption effective, or are multiple projectors connected? The display speed decreases when WEP encryption is effective or multiple projectors are connected.
Are you using Wireless LAN system 802.11b/g in Quick
Connection Mode?
Depending on the electromagnetic wave environment, there are times when the image and sound for movies may stop. When sending movies, use Advanced Connection Mode or set Wireless LAN system to 802.11a to use Quick
Connection Mode.
Troubleshooting
46
No audio from the projector when connecting with EasyMP Network Projection.
Check
Are multiple projectors connected to one computer?
Is audio set to output from the computer in Set Options?
Remedy
Audio can only be transferred to one projector. Try disconnecting other projectors.
Select Output audio from the projector on the Audio Output tab.
s
When a connection is made using EasyMP Network Projection, a PowerPoint Slide Show cannot be started.
Check
Was EasyMP Network Projection started while PowerPoint was running?
(For Windows)
Remedy
When connecting with EasyMP Network Projection, make sure you close PowerPoint first. Slide Show might not run if connecting while PowerPoint is running.
When a connection has been made using EasyMP Network Projection, the screen will not be refreshed when using an Office application.
Check
Is the mouse moved continuously?
Remedy
When you stop moving the mouse pointer the screen is updated. If the screen does not update quickly, stop moving the mouse pointer.
Error Message List
Cannot connect to the projector.
Error Messages
Cannot connect to the projector using this version of EasyMP
Network Connection. Install the latest version of EasyMP Network
Projection.
Remedy
Install the current version of EasyMP Network Projection from the EPSON Projector Software CD-ROM supplied with the projector.
You can download the latest version of EasyMP Network Projection from the following Web site.
http://www.epson.com/
Troubleshooting
47
Error message when starting up EasyMP Network Projection
Error Messages
Connection to the projector failed.
XXXXXX was disconnected.
The keyword does not match. Re-enter the keyword displayed on the projector screen.
The selected projector is busy. Do you want to continue the connection process?
Remedy
Try connecting again. If you still cannot connect to the projector, check the network settings on the computer and the network settings for the projector.
You can make network settings from the projector's Network menu.
See the following manual for details.
s User's Guide
Check the Projector Keyword displayed on the LAN standby screen, and enter the Projector Keyword.
EasyMP Network Projection initialization failed.
Connection failed due to keyword mismatch.
Network adapter information could not be obtained.
One or more connected projectors do not support resolutions greater than SXGA. Reduce the screen resolution and reconnect.
You tried to connect to a projector that is connected to another computer.
When Yes is clicked, a connection to the projector is established. The connection between the projector and the other computer is cut off.
When No is clicked, a connection to the projector is not established. The connection between the projector and the other computer is maintained.
Restart EasyMP Network Projection. If the message still appears, uninstall and then reinstall EasyMP Network
Projection.
s
When connecting to a projector for which a Projector Keyword has been set, the wrong Projector Keyword is entered.
Check the Projector Keyword that is displayed on the LAN standby screen.
s
Check the following point.
• Is a network adapter installed on the computer?
• Is the driver for the network adapter used installed on the computer?
• Is the network adapter enabled?
After checking, restart the computer and connect again.
If you still cannot connect, check the following.
Check the network settings on the computer and the network settings on the projector.
You can make network settings from the projector's Network menu.
See the following manual for details.
s User's Guide
There is an ELP-735 projector in the connection destination. Change the computer screen resolution to SXGA
(1280x1024) or less.
Troubleshooting
48
Error Messages
One or more projectors are not responding.
Enter the keyword displayed on the projector screen.
Cannot start this application while USB Display is running.
To output audio from the projector, restart applications such as
PowerPoint or Windows Media Player.
You need to restart your computer to enable Audio Output. Select
"Yes" to restart now or select "No" to restart later.
Cannot start this application while Quick Wireless Connection is running.
The wireless LAN is off. Turn on the wireless LAN, and then try searching again.
Remedy
Failed to simultaneously connect to one or more of the projectors that you attempted to connect to. Check the network settings on the computer and the network settings on the projector.
You can make network settings from the projector's Network menu.
See the following manual for details.
s User's Guide
Check the Projector Keyword displayed on the LAN standby screen, and enter the Projector Keyword.
Close USB Display and then start EasyMP Network Projection.
After restarting PowerPoint or Windows Media Player, audio is output from the projector.
To transfer audio to the projector and playback, select Yes and restart the computer.
Close Quick Wireless Connection and then start EasyMP Network Projection.
Turn on your computer's wireless LAN, and then try searching for the projector again.
Glossary
49
This section briefly explains the difficult terms that are not explained in the text of this guide. For details, refer to other commercially available publications.
MAC Address
SVGA
SXGA
UXGA
VGA
Virtual Display
WUXGA
XGA
An abbreviation of Media Access Control. The MAC Address is an ID number unique to each network adapter. A unique number is assigned to each network adapter, and data is transmitted between network adapters based on this identification.
A screen size standard with a resolution of 800 (horizontal) ^ 600 (vertical) dots.
A screen size standard with a resolution of 1,280 (horizontal) ^ 1,024 (vertical) dots.
A screen size standard with a resolution of 1,600 (horizontal) ^ 1,200 (vertical) dots.
A screen size standard with a resolution of 640 (horizontal) ^ 480 (vertical) dots.
The screen for one computer is output to multiple displays. A large virtual screen can be created by using multiple displays.
A screen size standard with a resolution of 1,920 (horizontal) ^ 1,200 (vertical) dots.
A screen size standard with a resolution of 1,024 (horizontal) ^ 768 (vertical) dots.
General Notes
50
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko
Epson Corporation. No patent liability is assumed with respect to the use of the information contained herein. Neither is any liability assumed for damages resulting from the use of the information contained herein.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the
U.S.) failure to strictly comply with Seiko Epson Corporation's operating and maintenance instructions.
Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options or any consumable products other than those designated as
Original Epson Products or Epson Approved Products by Seiko Epson Corporation.
The contents of this guide may be changed or updated without further notice.
Illustrations in this guide and the actual projector may differ.
About Notations
Microsoft ® Windows ® 2000 operating system
Microsoft ® Windows ® XP Professional operating system
Microsoft ® Windows ® XP Home Edition operating system
Microsoft ® Windows Vista ® operating system
Microsoft ® Windows ® 7 operating system
In this guide, the operating systems above are referred to as "Windows
2000," "Windows XP," "Windows Vista," and "Windows 7". Furthermore, the collective term Windows may be used to refer to Windows 2000,
Windows XP, Windows Vista, and Windows 7, and multiple versions of
Windows may be referred to as, for example, Windows 2000/XP/Vista, with the Windows notation omitted.
Mac OS X 10.4.x
Mac OS X 10.5.x
Mac OS X 10.6.x
Mac OS X 10.7.x
In this guide, the operating systems above are referred to as "Mac OS X
10.4.x," "Mac OS X 10.5.x," "Mac OS X 10.6.x", and "Mac OS X 10.7.x".
Furthermore, the collective term "Mac OS X" is used to refer to them all.
General Notice
IBM, DOS/V, and XGA are trademarks or registered trademarks of International
Business Machines Corporation.
Macintosh, Mac, Mac OS, and iMac are trademarks of Apple Inc.
Microsoft, Windows, Windows NT, Windows Vista, PowerPoint, and Windows logo are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries.
Other product names used herein are also for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.
Software Copyright:
This product uses free software as well as software to which this company holds the rights.
Z
SEIKO EPSON CORPORATION 2012. All rights reserved.
412213400EN
Index
51
A
Adjust performance ..................................... 36
Advanced connection mode ............ 9, 10, 11
Audio output ................................................ 37
Automatic search ......................................... 13
C
Clear list ........................................................ 14
Continuous Play .......................................... 25
Copy .............................................................. 20
Create folder ................................................. 21
D
Disable interrupt connection ..................... 13
Display ........................................................... 14
Display preferences ..................................... 30
Display properties ........................................ 29
E
Edit profile .............................................. 20, 36
G
General settings ............................................ 35
L
Limitations .................................................... 40
M
Manual search ........................................ 13, 17
Mirror displays ............................................. 31
Movie sending mode ............................. 15, 24
Multi-screen display .............................. 26, 27
O
Output audio from the projector ............... 37
P
Presentation mode ......................................... 5
Profile ............................................................ 14
Projector control .......................................... 15
Q
Quick connection mode ................... 9, 10, 11
R
Rename .......................................................... 21
S
Save in the profile ........................................ 14
Screen preview ............................................. 15
Select target projector ................................. 14
Set options .............................................. 14, 35
Signal intensity ....................................... 14, 15
SSID ............................................................... 14
Status ............................................................. 13
Switch LAN .................................................. 36
T
Toolbar .......................................................... 14
Transfer layered window ............................ 37
Troubleshooting .......................................... 13
U
Update list ..................................................... 13
Use full-screen video transfer .................... 35
Use multi-display ......................................... 13
V
Virtual display ........................................ 26, 27
advertisement
Related manuals
advertisement
Table of contents
- 2 Contents
- 4 About EasyMP Network Projection
- 5 Functions of EasyMP Network Projection
- 5 Various Screen Transfer Functions
- 6 Installing the Software
- 6 Software Requirements
- 7 Installing
- 8 Connecting the Computer and Projector
- 9 Two Connection Modes
- 9 Quick Connection Mode
- 9 Advanced Connection Mode
- 10 Preparing to Connect
- 11 Connecting to a Projector on a Network and Projecting
- 11 Operating the Computer
- 11 Security dialog displayed when connecting
- 12 Using the Connection Screen
- 14 Using the Toolbar
- 17 Connecting to a Projector on a Different Subnet
- 17 Specifying Either an IP Address or Projector Name and Performing a Search (Advanced Connection Mode ...
- 18 Performing a Search with a Profile
- 18 Making a Profile
- 19 Searching by specifying a Profile
- 20 Managing a Profile
- 22 Various Projection Styles
- 23 Projecting Only a PowerPoint Slide Show (Presentation Mode)
- 24 Projecting Movies on a Computer (Movie Sending Mode)
- 24 Supported Files
- 24 Playing Movies
- 26 Using Multi-Screen Display
- 26 Example of Adjusting the Virtual Display
- 27 Procedure Before Using the Multi-screen Display Function
- 27 Setting the Virtual Display
- 27 Enable the virtual display driver (Windows only)
- 28 Adjusting the Virtual Display
- 32 Allocating the Image to be Projected
- 32 Projecting the Allocated Images
- 34 Appendix
- 35 Set options
- 35 General settings tab
- 36 Adjust performance tab
- 37 Audio Output tab
- 39 Uninstalling the Software
- 40 Connection Limitations
- 40 Supported Resolutions
- 40 Display Color
- 40 Other Limitations
- 40 When Using Windows Vista or Windows 7
- 40 Limitations when projecting from Windows Photo Gallery or Windows Live Photo Gallery
- 41 Limitations in Windows Aero
- 41 Limitations when projecting from Windows Media Center
- 42 Troubleshooting
- 42 Cannot connect to the projector you want to use.
- 42 Cannot connect the projector and the computer via wireless LAN.
- 43 Cannot connect the projector and the computer via wired LAN.
- 43 Cannot connect the projector and the computer via the network.
- 44 When a connection is made using EasyMP Network Projection, the projected image remains as it is, and ...
- 44 Cannot select or change the connection mode.
- 44 The screen is not projected.
- 44 The Slide Show cannot be displayed on the desired display when the multi-screen display function is ...
- 45 Applications are no longer displayed from the computer screen when the multi-screen display function ...
- 45 The mouse pointer is not displayed on the computer screen.
- 45 The mouse pointer flickers.
- 45 When connecting with EasyMP Network Projection the image is not displayed or the image is slow to ap ...
- 46 No audio from the projector when connecting with EasyMP Network Projection.
- 46 When a connection is made using EasyMP Network Projection, a PowerPoint Slide Show cannot be started.
- 46 When a connection has been made using EasyMP Network Projection, the screen will not be refreshed wh ...
- 46 Error Message List
- 46 Cannot connect to the projector.
- 47 Error message when starting up EasyMP Network Projection
- 49 Glossary
- 50 General Notes
- 50 About Notations
- 50 General Notice
- 51 Index