Electric Vehicle AC Charger
EVC12 Series (EU) - User Manual
USER MANUAL
1. Important Safety Instructions
This charger complies with IEC61851 and CE-LVD.
When using electric products, basic precautions should always be followed.
This manual contains important instructions, including the following, that must be followed
during installation, operation and maintenance.
• Do not install or use the charger near flammable, explosive, corrosive, or combustible
materials, chemicals, or vapors.
• Turn off the input power of the charger before maintaining the charger.
• The device is designed only for vehicles that are compatible with the Model 3 charging
standard.
• Do not use the charger if it is defective, appears cracked, frayed, broken or damaged.
• Do not attempt to open, disassemble, repair, tamper with, or modify the charger. Contact our
Customer Service for any requirement of repair.
• Do not use the charger when you are in the vehicle, or the charger is exposed to severe rain,
snow, or other severe weather.
USER MANUAL
• Risk of electric shock. Do not remove cover or attempt to open the enclosure of the device.
No user serviceable parts inside. Refer servicing to qualified service personnel.
• To reduce the risk of serious injury or death and damage to the charge, this device should be
installed, adjusted, and serviced by qualified electrical personnel familiar with the construction
and operation of this type of charger and the danger involved. Failure to observe this precaution could result in death or severe injury.
• Incorrect installation and testing of the charger could potentially damage either the vehicle's
battery and/or the device itself. Any resulting damage is excluded from the warranty for the
device.
• Ensure that the charging cable is well positioned during charging so it will not be stepped on,
tripped over, or subjected to damage or stress.
• Do not use this charger with a frayed charging cable that has damaged insulation or any other
sign of damage.
• According to the local electrical requirements, confirm the wire diameter and wire type
corresponding to the current rating and the temperature rating must meet the requirements.
• Before starting the installation, turn off all power.
For safe use of electricity, please add circuit breaker protection in the input part of charging
pile, install certified type A RCD and circuit breaker (Schneider) upstream close to AC charger.
• When transporting the charger, handle with care and do not drag or step on the device.
• Do not touch the charging connector terminal with sharp metallic objects for preventing
Circuit Breaker Options Table
damage.
• Do not forcefully pull the charging cable, damage it with sharp objects, put fingers, or insert
foreign objects into any part of the charging connector.
• Risk of explosion. This device has arcing or sparking parts that should not be exposed to
flammable vapors.
3-phase
1-phase
AC Charger Output Amperage (A)
32A
16A
32A
Circuit Breaker Options (A)
40A
20A
40A
A9F18240
A9F18420
A9F18440
Circuit Breaker Model
2. Basic Interface
3. Dimensions
250.0mm
LED Light
Indication
361.5mm
111.5mm
Rear Notch
4-Φ9mm
122mm
Charging Cable Inlet
LAN Cable Inlet
Charging Cable Inlet
72mm
USER MANUAL
USER MANUAL
4. Specification
5. Status Description of the Charger Indication Light
EVC12 Version
Model Name
Rated Input Voltage
230VAC±10% / Single Phase
400VAC+10% / Three Phase
Rated Output Current
32A
16/32A
AC Power Frequency
50/60 Hz
Input Protection
UVP, OVP, RCD, SPD, Ground Fault Protection
Output Protection
OCP, OTP, Control Pilot Fault Protection
Output Interface
IEC 62196-2 AC Charging Connector
Storage Temperature
-40°C to +70°C
Operation Temperature
-30°C to +50°C
Relative Operation Humidity
95% RH Maximum
Relative Storage Humidity
95% RH Maximum
Version
Standby - Blue Light
The READY light stays steady in
standby mode.
LAN Version / Wi-Fi Bluetooth Version
RJ45 Cable lnlet*1
10M/100M Base-T
Wi-Fi Function*2
802.11 b/g/n
Cable Length
5m
Protection Level
IP65
Installation Type
Wall-Mounted
Altitude
Status Indication
*1 LAN Version or Wi-Fi & Bluetooth Version
*2 Wi-Fi & Bluetooth Version
READY
CHARGE Waiting for Charging - Green Light
After the vehicle connector is connected
to the vehicle inlet, the CHARGE light is
constantly lit
≤ 2000 m
Red, Green, Blue LED
CHARGE Charging - Green Light Flashing
The CHARGE light flashes while
charging.
USER MANUAL
USER MANUAL
No.
FAULT
Fault - Red Light
The red light is lit while fault. Please
refer to "8.3 Error and Warning
Messages" for detailed information.
6. Packing List
Product Name
Quantity Note
AC Charger (With Charging Cable)
1
User Manual
1
Wall-Mounted Bracket
1
M5 teeth screws
2
M6 Hexagonal Expansion Screws
4
7 Installation Instructions
7.1 Safety Requirements
EVC12 Series (EU) - User Manual
• Be sure to preview the user manual and ensure local building and electrical codes are
reviewed before installing the AC charger.
• The AC charger should be installed by a qualified technician according to the user manual
and local safety regulations.
• Use appropriate protection when connecting to the main power distribution cable.
• Type B, C or D breaker with the rating current for table should be installed in the upstream
AC distribution box.
• Disconnect switch for each ungrounded conductor of AC input shall be provided by others.
USER MANUAL
USER MANUAL
7.2 Wiring
For safe use of electricity, please add circuit breaker protection in the input part
For safe use of electricity, please add circuit breaker protection in the input part
of charging pile. Connect the L1 lead to the grid L1, connect the L2 lead to the grid L2,
of charging pile. Connect the L lead to the grid L, connect the N lead to the grid N,
connect the L3 lead to the grid L3, connect the N lead to the grid N, connect the PE lead
connect the PE lead to the grid PE (for Single Phase).
to the grid PE (for Three Phase)
L1 L2 L3 N PE
L N PE
Circuit Breaker Options table
Circuit Breaker Options table
Output Amperage (A)
32A
Circuit Breaker Options (A)
40A
Output Amperage (A)
16A
32A
Circuit Breaker Options (A)
20A
40A
7.3 Tools and Materials Required
7.4 Wall-Mounted Bracket Installation
Tools required before installing the Wall-Mounted charger, gather the following tools:
Step 1:
• Wire stripper
• Set the positions of the 4 screw holes and drill them, with a diameter of 8mm and
• Crimpers for European terminals
a depth of 52mm.
• Phillips screwdriver for M5
• Use 4 sets expansion screw and M6 screw to fix the wall-mounted bracket on the wall.
• Slotted screwdriver for 4~5.5MM
• Adjustable Wrench M6
• Head gasket screw 10-10.5mm
• Voltmeter or digital multi-meter (for measuring AC voltage at the installation site)
• The inserting cable should meet the best waterproof performance. It is recommended to use
3 core/6mm cable for Single Phase / 5 core/6mm cable for three phase (XLPE or equivalent
cable) to pull the cable from the distribution box.
• Level ruler
• Pencil or marker
• Machine drill
Installation Instructions
“This device shall be mounted at a sufficient height from grade such that the height of the
storage means for the coupling device is located between 600mm (24 inches) and 1.2m (4
feet) from grade.”
Step 2: Align the rear notch of charger into the wall-mounted bracket and fit the screw
holes of the right and left side.
USER MANUAL
USER MANUAL
Step 3: Fix two M5 screws to complete the installation.
8. Operating Instructions
8.1 Operating Procedures
● User authorization
● Connect to Vehicle Charging Inlet
● Charging Message
● Charging completed
8.2 Operating Steps
Step 1 / Standby Mode
After power-on, blue light (READY), green light (CHARGE) and red light (FAULT) all lit.
Overall outlook picture after installation:
Enter standby mode and the blue light (READY) is steady on.
Wall-mounted cable winding
READY
Step 2 / Plug the Charging Connector
Please plug the charging connector into the vehicle charging inlet.
13
14
USER MANUAL
USER MANUAL
8.3 Error and Warning Message
Step 3 / Charging
The green light (CHARGE) turns to flash automatically, charging is in process.
• If the red light (FAULT) is lit, plug the vehicle connector again.
• If red light is still lit, please refer to "Error and Warning Messages".
CHARGE
Step 4 / Charging Finished
When the charging is finished, the green light (CHARGE) is constantly lit, please
remove the plug.
15
Status
Red
Remark
Input OVP
1 flashes followed by 3 sec pause
Auto Recover
Input UVP
2 flashes followed by 3 sec pause
Auto Recover
Output OCP
3 flashes followed by 3 sec pause
Auto Recover
OTP
4 flashes followed by 3 sec pause
Auto Recover
RCD Abnormal
5 flashes followed by 3 sec pause
Auto Recover
Ground Fault
6 flashes followed by 3 sec pause
Auto Recover
Control Pilot Fault
Flicker
Auto Recover
MCU Self-Test Fail
Constantly Bright
Contact Customer Service
RCD Self-Test Fail
Constantly Bright
Contact Customer Service
Relay Self-Test Fail
Constantly Bright
Contact Customer Service
RCD Abnormal Stop Charging
Constantly Bright
Contact Customer Service
Output OCP Stop Charging
Constantly Bright
Contact Customer Service
OTP Stop Charging
Constantly Bright
Contact Customer Service
16
USER MANUAL
USER MANUAL
9. Maintenance and Repair
• During the warranty period for any malfunction caused by normal use according to the User
9.1 Daily Maintenance
Technology), the product shall be repaired free of charge. Except for the following situations,
Manual and Service Instruction (to be determined by certified maintenance technicians of Joint
Please keep the charger clean and keep the charge in a clean area with low humidity. Do not
the charger shall be subject to the above warranty terms:
install it in an environment near the sea, with high oil, high humidity or high dust.
1. The warranty certificate cannot be provided or the contents of the warranty certificate are
• Avoid moisture or water in the charger. If there is water or moisture ingress into the charger, it
modified or inconsistent with the label indication of the repaired product.
is necessary to immediately power off to avoid immediate danger, and notify the professional
2. Those who are unable to provide valid proof of purchase.
personnel to carry out maintenance before next use.
3. Those who exceed the manufacturer's specified warranty period.
• If there is any damage or dirt on the vehicle connector, charging cable, or vehicle connector
4. Those who damage the product due to not following the product service instruction for use,
holder, please contact the maintenance personnel immediately.
maintenance and storage.
• Please use the charger properly. Do not hit or press hard on the case. If the case is damaged,
5. Damage or malfunction caused by foreign object entering.
please contact a professional technician.
6. Unauthorized repair, disassembly or modification.
• Avoid placing the charger near hot objects and at high temperature locations and away from
7. Damage caused by force majeure (such as lightning, excessive voltage, earthquake, fire,
dangerous substances such as flammable gases and corrosive materials.
flood, etc.).
• Do not place external objects or heavy objects on the charger to avoid danger.
8. Malfunction and damage caused by other unavoidable external factors. Malfunction and
9.2 Maintenance Spares
damage caused by improper use of equipment, such as water or other solutions entering into
the equipment.
• This charger is equipped with maintenance spares for maintenance use during and over the
9. Malfunction and damage caused by the grid power supply and voltage which is not specified
warranty period. All warranty services and repairs shall be and performed by certified service
for use with the charger equipment.
technicians authorized by Joint Technology. For details, please contact your local Joint Tech-
• The above guarantees shall be made solely, and no other express or implied warranties shall
nology service partner or direct to our Customer Service.
be made (including the implied warranties of merchant ability, particular and applicable reason-
9.3 Warranty and Maintenance
ableness and adaptability, etc.) whether in the contract, civil negligence, or other aspects, the
Company shall not be responsible for any special, incidental or consequential damages.
• The warranty period for this charger is two years.
• After the event of any repair or maintenance under the warranty period, if there is no purchase
to extend the warranty service, Joint Technology shall provide a three-month warranty period
for any subsequent paid repair work.
17
18
">
