Electric Vehicle AC Charger
EVC11 Series (NA) - User Manual
USER MANUAL
USER MANUAL
WARNING
WARNING
1. Important Safety Instructions
AVERTISSEMENT – Ce manuel contient des instructions importantes pour les modèles :
série EVC11 qui doit être suivie pendant l'installation, le fonctionnement et la maintenance de
l'unité.
WARNING – This manual contains important instructions for Models:
EVC11 series that shall be followed during installation, operation and maintenance of the unit.
1) Read all the instructions before using this product.
1) Lisez toutes les instructions avant d'utiliser ce produit.
2) Cet appareil doit être surveillé lorsqu'il est utilisé à proximité d'enfants.
3) Ne pas mettre les doigts dans le connecteur du véhicule électrique.
2) This device should be supervised when used around children.
4) N'utilisez pas ce produit si le cordon d'alimentation flexible ou le câble EV est effiloché, a
3) Do not put fingers into the electric vehicle connector.
4) Do not use this product if the flexible power cord or EV cable is frayed, has broken insulation,
or any other signs of damage.
5) Do not use this product if the enclosure or the EV connector is broken, cracked, open, or
shows any other indication of damage.
6) To reduce the risk of fire, connect only to a circuit provided branch circuit over-current
protection in accordance with the CSA C22.1–15 Canadian Electrical Code, Part 1 (Canada) or
NOM-001-SEDE Electrical installations (utility) (Mexico) or ANSI / NFPA 70 National Electrical
une isolation cassée, ou tout autre signe de dommage.
5) N'utilisez pas ce produit si le boîtier ou le connecteur EV est cassé, fissuré, ouvert ou
montre toute autre indication de dommage.
6) Pour réduire les risques d'incendie, ne connecter qu'à un circuit protection contre les
surintensités des circuits de dérivation conformément à la norme canadienne CSA C22.1-15
Code électrique, partie 1 (Canada) ou NOM-001-SEDE Installations électriques (service public)
(Mexique) ou ANSI / NFPA 70 National Electrical Code (États-Unis).
Code (USA).
Circuit Breaker Options table
Circuit Breaker Options table
Output Amperage (A)
16A
32A
40A
48A
Circuit Breaker Options (A)
20A
40A
50A
60A
7) To avoid a risk of fire or electric shock, do not use this device with an extension cord.
8) THE SUITABILITY OF THE USE OF FLEXIBLE CORD IN ACCORDANCE WITH CE CODE,
PART I, RULE 4-012, IS TO BE DETERMINED BY THE LOCAL INSPECTION AUTHORITY
HAVING JURISDICTION.
9) Risk of electric shock. Do not remove cover or attempt to open the enclosure. No user
serviceable parts inside. Refer servicing to qualified service personnel.
Output Amperage (A)
16A
32A
40A
48A
Circuit Breaker Options (A)
20A
40A
50A
60A
7) Pour éviter tout risque d'incendie ou de choc électrique, n'utilisez pas cet appareil avec une
rallonge.
8) L'ADÉQUATION DE L'UTILISATION DU CORDON FLEXIBLE SELON LE CODE CE,LA
PARTIE I, RÈGLE 4-012, DOIT ÊTRE DÉTERMINÉE PAR L'AUTORITÉ LOCALE D'INSPECTION AYANT JURIDICTION.
9) Risque de choc électrique. Ne retirez pas le couvercle et n'essayez pas d'ouvrir le boîtier.
Aucun utilisateur pièces réparables à l'intérieur. Confiez l'entretien à un personnel d'entretien
qualifié.
01
02
USER MANUAL
USER MANUAL
WARNING
2. Basic Interface
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
This device may not cause harmful interference, and this device must accept any interference
received, including interference that may cause undesired operation.
LED Light
Indication
Caution: Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class A digital
SAE J1772
AC Charging
Connector
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at
his own expense.
WIFI module：Contians FCC ID:2AC7Z-ESPWROOM32D
LTE module：Contians FCC ID:XMR201909EC25AFX
Rear Notch
IC:10224A-2019EC25AFX
To satisfy FCC RF exposure requirements, a separation distance of 20cm or more should be
maintained between the antenna of this device and persons during device operation. To ensure
compliance, operations at closer than this distance is not recommended.
Charging Cable Inlet
AC Power Inlet
LAN Cable Inlet
03
04
USER MANUAL
USER MANUAL
4. Design Standard
3. Dimensions
UL 2594: Electric Vehicle Supply Equipment
9.8″
3.9″
UL 2231-1: Personnel Protection Systems for Electric Vehicle (EV) Supply Circuits: General
Requirements
UL 2231-2: Personnel Protection Systems for Electric Vehicle (EV) Supply
Circuits: Particular Requirements for Protection Devices for Use in Charging Systems
UL 2251: Plugs, Receptacles and Couplers for Electric Vehicles
UL 62: Flexible Cords and Cables
UL 991: Tests for Safety-Related Controls Employing Solid-State Devices
14.2″
UL 1998: Software in Programmable Componets
NFPA 70 Article 625: National Electrical Code, Electric Vehicle Charging System
UL 840 (Clearance and Creepage)
4-Φ0.35″
4.8″
2.83″
05
06
USER MANUAL
USER MANUAL
5. Specification
6. Status Description of the Charger Indication Light
Model Name
EVC11 Version
Rated Input Voltage
200-240 VAC
Rated Output Current
16/32/40/48A
AC Power Frequency
60 Hz
Input Protection
UVP, OVP, RCD, SPD, Ground Fault Protection
Output Protection
OCP, OTP, Control Pilot Fault Protection
Output Interface
SAE J1772 AC Charging Connector
Storage Temperature
-40°F to 158°F
Operation Temperature
-22°F to 122°F
Standby - Blue Light
The READY light stays steady in
standby mode.
Relative Operation Humidity
95% RH Maximum
Relative Storage Humidity
95% RH Maximum
Waiting for Charging - Green Light
RFID Authentication
LAN Version / Wi-Fi Version
After the vehicle connector is connected
RJ45 Cable Inlet*1
10M / 100M Base-T
to the vehicle inlet, the CHARGE light
Wi-Fi Function*2
802.11 b/g/n
Cable Length
18ft
Protection Level
Type 3
Installation Type
Wall-Mounted
Altitude
Status Indication
will constantly lit.
≤ 6561ft
Red, Green, Blue LED
Charging - Green Light Flashing
*1 LAN Version or Wi-Fi Version
The CHARGE light flashes while
*2 Wi-Fi Version
charging.
07
08
USER MANUAL
USER MANUAL
FAULT
Fault - Red Light
The red light is lit while fault. Please
refer to "9.3 Error and Warning
Messages" for detailed information.
No.
Product Name
Quantity Note
1
AC Charger (With Charging Cable)
1
2
User Manual
1
3
Wall-Mounted Bracket
1
4
M5 teeth screws
2
5
M6 Hexagonal Expansion Screws
4
6
RFID Card (RFID Version Only)
2
7. Packing List
8 Installation Instructions
Electric Vehicle AC Charger
EVC11 Series (NA) - User Manual
8.1 Safety Requirements
• Be sure to preview the user manual and ensure local building and electrical codes are
reviewed before installing the AC charger.
1
2
3
• The AC charger should be installed by a qualified technician according to the user manual
and local safety regulations.
• Use appropriate protection when connecting to the main power distribution cable.
• Type B, C or D breaker with the rating current for table should be installed in the upstream
AC distribution box.
D
FI
R
• Disconnect switch for each ungrounded conductor of AC input shall be provided by others in
accordance with the National Electric Code, ANSI/NFPA 70.
4
09
5
6
10
USER MANUAL
8.2 Wiring
GROUNDING INSTRUCTIONS
This product must be grounded. If it should malfunction or break down, grounding provides a
USER MANUAL
For safe use of electricity, please add circuit breaker protection in the input part
of charging pile. Connect the L1 lead to the grid L1, connect the L2 lead to the grid L2,
connect the PE lead to the grid PE (for all Version).
path of least resistance for electric current to reduce the risk of electric shock. This product is
equipped with a cord having an equipment grounding conductor and a grounding plug. The
plug must be plugged into an appropriate outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
WARNING – Improper connection of the equipment-grounding conductor is able to result in a
risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to
whether the product is properly grounded. Do not modify the plug provided with the product – if
it will not fit the outlet, have a proper outlet installed by a qualified electrician.
IAVERTISSEMENT - Une mauvaise connexion du conducteur de mise à la terre de l'équipement peut entraîner un risque de choc électrique. Vérifiez auprès d'un électricien ou d'un
L1 L2 PE
technicien qualifié si vous n'êtes pas sûr que le produit soit correctement mis à la terre. Ne
modifiez pas la fiche fournie avec le produit - si elle ne rentre pas dans la prise, faites installer
une prise appropriée par un électricien qualifié.
11
Circuit Breaker Options table
Output Amperage (A)
16A
32A
40A
48A
Circuit Breaker Options (A)
20A
40A
50A
60A
12
USER MANUAL
8.3 Tools and Materials Required
USER MANUAL
8.4 Wall-Mounted Bracket Installation
Tools required before installing the Wall-Mounted charger, gather the following tools:
Step 1:
• Wire stripper
• Set the positions of the 4 screw holes and drill them, with a diameter of 8mm and
• Crimpers for European terminals
a depth of 52mm.
• Phillips screwdriver for M5
• Use 4 sets expansion screw and M6 screw to fix the wall-mounted bracket on the wall.
• Slotted screwdriver for 4~5.5MM
• Adjustable Wrench M6
• Head gasket screw 10-10.5mm
• Voltmeter or digital multi-meter (for measuring AC voltage at the installation site)
• The inserting cable should meet the best waterproof performance. It is recommended to use
3 core / 7AWG cable (XLPE or equivalent cable) to pull the cable from the distribution box.
• Level ruler
• Pencil or marker
• Machine drill
Installation Instructions
“This device shall be mounted at a sufficient height from grade such that the height of the
storage means for the coupling device is located between 600mm (24 inches) and 1.2m (4
feet) from grade.”
Step 2: Align the rear notch of charger into the wall-mounted bracket and fit the screw
holes of the right and left side.
13
14
USER MANUAL
USER MANUAL
Step 3: Fix two M5 screws to complete the installation.
9. Operation Instuctions
9.1 Operating Procedures
User authorization
Connect to Vehicle Charging Inlet
Charging Message
Charging completed
9.2 Operating Steps
9.2.1 Operating Steps with Plug and Charge
Step 1 / Standby Mode
After power-on, blue light (READY), green light (CHARGE) and red light (FAULT) all lit.
Overall outlook picture after installation:
Enter standby mode and the blue light (READY) is steady on.
Wall-mounted cable winding
Optional cable hanging(optional accessory)
READY
Step 2 / Plug the Charging Connector
Please plug the charging connector into the vehicle charging inlet.
15
16
USER MANUAL
USER MANUAL
9.2.2 Operating Steps with RFID
Step 3 / Charging
The green light (CHARGE) turns to flash automatically, charging is in process.
• If the red light (FAULT) is lit, plug the vehicle connector again.
• If red light is still lit, please refer to "Error and Warning Messages".
Step 1 / Standby Mode
After power-on, blue light (READY), green light (CHARGE) and red light (FAULT) all lit.
Enter standby mode and the blue light (READY) is steady on.
CHARGE
READY
Step 4 / Charging Finished
Step 2 / Tap the RFID Card
When the charging is finished, the green light (CHARGE) is constantly lit, please
Please plug the charging connector into the vehicle charging inlet. When you tap the
press the button on connector.
RFID card first, it needs to complete the insertion of the charging connector within 120
seconds, otherwise you need to tap the RFID card again.
17
18
USER MANUAL
USER MANUAL
9.3 Error and Warning Message
Step 3 / Tap the RFID Card
Tap the RFID card to start the charging.
Status
Red
Remark
Input OVP
1 flashes followed by 3 sec pause
Auto Recover
Input UVP
2 flashes followed by 3 sec pause
Auto Recover
Output OCP
3 flashes followed by 3 sec pause
Auto Recover
OTP
4 flashes followed by 3 sec pause
Auto Recover
RCD Abnormal
5 flashes followed by 3 sec pause
Auto Recover
Ground Fault
6 flashes followed by 3 sec pause
Auto Recover
Control Pilot Fault
Flicker
Auto Recover
The green light (CHARGE) turns to flash automatically, charging is in process.
MCU Self-Test Fail
Constantly Bright
Contact Customer Service
• If the red light (FAULT) is lit, plug the vehicle connector again.
RCD Self-Test Fail
Constantly Bright
Contact Customer Service
Relay Self-Test Fail
Constantly Bright
Contact Customer Service
RCD Abnormal Stop Charging
Constantly Bright
Contact Customer Service
Output OCP Stop Charging
Constantly Bright
Contact Customer Service
OTP Stop Charging
Constantly Bright
Contact Customer Service
Step 4 / Charging
• If red light is still lit, please refer to "Error and Warning Messages".
CHARGE
Step 5 / Charging Finished
When the charging is finished, the green light (CHARGE) is constantly lit, please
press the button on connector.
19
20
USER MANUAL
USER MANUAL
10. Maintenance and Repair
• During the warranty period for any malfunction caused by normal use according to the User
10.1 Daily Maintenance
Technology), the product shall be repaired free of charge. Except for the following situations,
Please keep the charger clean and keep the charge in a clean area with low humidity. Do not
the charger shall be subject to the above warranty terms:
install it in an environment near the sea, with high oil, high humidity or high dust.
1. The warranty certificate cannot be provided or the contents of the warranty certificate are
• Avoid moisture or water in the charger. If there is water or moisture ingress into the charger, it
modified or inconsistent with the label indication of the repaired product.
is necessary to immediately power off to avoid immediate danger, and notify the professional
2. Those who are unable to provide valid proof of purchase.
personnel to carry out maintenance before next use.
3. Those who exceed the manufacturer's specified warranty period.
• If there is any damage or dirt on the vehicle connector, charging cable, or vehicle connector
4. Those who damage the product due to not following the product service instruction for use,
holder, please contact the maintenance personnel immediately.
maintenance and storage.
• Please use the charger properly. Do not hit or press hard on the case. If the case is damaged,
5. Damage or malfunction caused by foreign object entering.
please contact a professional technician.
6. Unauthorized repair, disassembly or modification.
• Avoid placing the charger near hot objects and at high temperature locations and away from
7. Damage caused by force majeure (such as lightning, excessive voltage, earthquake, fire,
dangerous substances such as flammable gases and corrosive materials.
flood, etc.).
• Do not place external objects or heavy objects on the charger to avoid danger.
8. Malfunction and damage caused by other unavoidable external factors. Malfunction and
Manual and Service Instruction (to be determined by certified maintenance technicians of Joint
damage caused by improper use of equipment, such as water or other solutions entering into
10.2 Maintenance Spares
the equipment.
• This charger is equipped with maintenance spares for maintenance use during and over the
9. Malfunction and damage caused by the grid power supply and voltage which is not specified
warranty period. All warranty services and repairs shall be and performed by certified service
for use with the charger equipment.
technicians authorized by Joint Technology. For details, please contact your local Joint Tech-
• The above guarantees shall be made solely, and no other express or implied warranties shall
nology service partner or direct to our Customer Service.
be made (including the implied warranties of merchant ability, particular and applicable reasonableness and adaptability, etc.) whether in the contract, civil negligence, or other aspects, the
10.3 Warranty and Maintenance
• The warranty period for this charger is two years.
Company shall not be responsible for any special, incidental or consequential damages.
• After the event of any repair or maintenance under the warranty period, if there is no purchase
to extend the warranty service, Joint Technology shall provide a three-month warranty period
for any subsequent paid repair work.
21
22
">
