Electric Vehicle AC Charger
EVC10 Series (NA) - User Manual
USER MANUAL
USER MANUAL
WARNING
WARNING
1. Important Safety Instructions
AVERTISSEMENT – Ce manuel contient des instructions importantes pour les modèles :
série EVC10 qui doit être suivie pendant l'installation, le fonctionnement et la maintenance de
l'unité.
WARNING – This manual contains important instructions for Models:
EVC10 series that shall be followed during installation, operation and maintenance of the unit.
1) Read all the instructions before using this product.
1) Lisez toutes les instructions avant d'utiliser ce produit.
2) Cet appareil doit être surveillé lorsqu'il est utilisé à proximité d'enfants.
3) Ne pas mettre les doigts dans le connecteur du véhicule électrique.
2) This device should be supervised when used around children.
4) N'utilisez pas ce produit si le cordon d'alimentation flexible ou le câble EV est effiloché, a
3) Do not put fingers into the electric vehicle connector.
4) Do not use this product if the flexible power cord or EV cable is frayed, has broken insulation,
or any other signs of damage.
5) Do not use this product if the enclosure or the EV connector is broken, cracked, open, or
shows any other indication of damage.
6) To reduce the risk of fire, connect only to a circuit provided branch circuit over-current
protection in accordance with the CSA C22.1–15 Canadian Electrical Code, Part 1 (Canada) or
NOM-001-SEDE Electrical installations (utility) (Mexico) or ANSI / NFPA 70 National Electrical
une isolation cassée, ou tout autre signe de dommage.
5) N'utilisez pas ce produit si le boîtier ou le connecteur EV est cassé, fissuré, ouvert ou
montre toute autre indication de dommage.
6) Pour réduire les risques d'incendie, ne connecter qu'à un circuit protection contre les
surintensités des circuits de dérivation conformément à la norme canadienne CSA C22.1-15
Code électrique, partie 1 (Canada) ou NOM-001-SEDE Installations électriques (service public)
(Mexique) ou ANSI / NFPA 70 National Electrical Code (États-Unis).
Code (USA).
Circuit Breaker Options table
Circuit Breaker Options table
Output Amperage (A)
16A
32A
40A
48A
Circuit Breaker Options (A)
20A
40A
50A
60A
7) To avoid a risk of fire or electric shock, do not use this device with an extension cord.
8) THE SUITABILITY OF THE USE OF FLEXIBLE CORD IN ACCORDANCE WITH CE CODE,
PART I, RULE 4-012, IS TO BE DETERMINED BY THE LOCAL INSPECTION AUTHORITY
HAVING JURISDICTION.
9) Risk of electric shock. Do not remove cover or attempt to open the enclosure. No user
serviceable parts inside. Refer servicing to qualified service personnel.
Output Amperage (A)
16A
32A
40A
48A
Circuit Breaker Options (A)
20A
40A
50A
60A
7) Pour éviter tout risque d'incendie ou de choc électrique, n'utilisez pas cet appareil avec une
rallonge.
8) L'ADÉQUATION DE L'UTILISATION DU CORDON FLEXIBLE SELON LE CODE CE,LA
PARTIE I, RÈGLE 4-012, DOIT ÊTRE DÉTERMINÉE PAR L'AUTORITÉ LOCALE D'INSPECTION AYANT JURIDICTION.
9) Risque de choc électrique. Ne retirez pas le couvercle et n'essayez pas d'ouvrir le boîtier.
Aucun utilisateur pièces réparables à l'intérieur. Confiez l'entretien à un personnel d'entretien
qualifié.
01
02
USER MANUAL
USER MANUAL
WARNING
2. Basic Interface
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
This device may not cause harmful interference, and this device must accept any interference
received, including interference that may cause undesired operation.
LED Light
Indication
Caution: Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class A digital
SAE J1772
AC Charging
Connector
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at
his own expense.
WIFI module：Contians FCC ID:2AC7Z-ESPWROOM32D
LTE module：Contians FCC ID:XMR201909EC25AFX
Rear Notch
IC:10224A-2019EC25AFX
To satisfy FCC RF exposure requirements, a separation distance of 20cm or more should be
maintained between the antenna of this device and persons during device operation. To ensure
compliance, operations at closer than this distance is not recommended.
Charging Cable Inlet
AC Power Inlet
LAN Cable Inlet
03
04
USER MANUAL
USER MANUAL
3. Dimensions
4. Design Standard
UL 2594: Electric Vehicle Supply Equipment
UL 2231-1: Personnel Protection Systems for Electric Vehicle (EV) Supply Circuits: General
9.8″
5.1″
Requirements
UL 2231-2: Personnel Protection Systems for Electric Vehicle (EV) Supply
Circuits: Particular Requirements for Protection Devices for Use in Charging Systems
UL 2251: Plugs, Receptacles and Couplers for Electric Vehicles
UL 62: Flexible Cords and Cables
UL 991: Tests for Safety-Related Controls Employing Solid-State Devices
13.8″
UL 1998: Software in Programmable Componets
NFPA 70 Article 625: National Electrical Code, Electric Vehicle Charging System
UL 840 (Clearance and Creepage)
4-Φ0.35″
4.8″
2.83″
05
06
USER MANUAL
USER MANUAL
5. Specification
6. Status Description of the Charger Indication Light
EVC10 Version
Model Name
Rated Input Voltage
200-240 VAC / Single Phase
Rated Output Current
16/32/40/48A
AC Power Frequency
60 Hz
Input Protection
UVP, OVP, RCD, SPD, Ground Fault Protection
Output Protection
OCP, OTP, Control Pilot Fault Protection
Output Interface
SAE J1772 AC Charging Connector
Storage Temperature
-40°F to 158°F
Operation Temperature
-22°F to 122°F
Relative Operation Humidity
95% RH Maximum
Relative Storage Humidity
95% RH Maximum
Version
READY
10M/100M Base-T
Wi-Fi Function*2
802.11 b/g/n
3G/4G Fnction*3
LTE, GSM/GPRS
Cable Length
18ft
Protection Level
Type 3
Installation Type
Wall-Mounted
Altitude
Status Indication
*1 LAN Version or Wi-Fi Version or 4G Version
The READY light stays steady in
standby mode.
Waiting for Charging - Green Light
LAN Version / Wi-Fi Version / 4G Version
RJ45 Cable Inlet*1
*2 Wi-Fi Version
Standby - Blue Light
CHARGE
After the vehicle connector is connected
to the vehicle inlet, the CHARGE light is
constantly lit.
≤ 6561ft
Charging - Green Light Flashing
Red, Green, Blue LED
CHARGE
The CHARGE light flashes while
charging.
*3 4G Version
07
08
USER MANUAL
USER MANUAL
Fault - Red Light
FAULT
The red light is lit while fault. Please
refer to "9.3 Error and Warning
Messages" for detailed information.
7. Packing List
No.
Product Name
Quantity Note
1
AC Charger (With Charging Cable)
1
2
User Manual
1
3
Wall-Mounted Bracket
1
4
M5 teeth screws
2
5
M6 Hexagonal Expansion Screws
4
6
RFID Card (RFID Version Only)
2
8 Installation Instructions
Electric Vehicle AC Charger
8.1 Safety Requirements
EVC10 Series (NA) - User Manual
• Be sure to preview the user manual and ensure local building and electrical codes are
reviewed before installing the AC charger.
• The AC charger should be installed by a qualified technician according to the user manual
1
2
and local safety regulations.
3
• Use appropriate protection when connecting to the main power distribution cable.
• Type B, C or D breaker with the rating current for table should be installed in the upstream
AC distribution box.
• Disconnect switch for each ungrounded conductor of AC input shall be provided by others in
D
FI
R
4
09
5
accordance with the National Electric Code, ANSI/NFPA 70.
6
10
USER MANUAL
USER MANUAL
8.2 Installation Steps
Step 3: Tighten 13 screws on the front cover after the front cover is put back, the
Step 1: Use screwdriver to loosen the 13 fixed screws on the rear of charger,
recommended screw torque is 1.0 N.m (9.6 lbf.in) (for 4G Version).
8
then remove the front cover (for 4G Version).
8
7
6
4
10
3
11
2
13
6
5
9
4
10
3
11
2
5
9
12
7
12
13
1
1
8.3 Wiring
Step 2: Insert the SIM card according to the picture's instruction (for 4G Version)..
GROUNDING INSTRUCTIONS
This product must be grounded. If it should malfunction or break down, grounding provides a
path of least resistance for electric current to reduce the risk of electric shock. This product is
equipped with a cord having an equipment grounding conductor and a grounding plug. The
plug must be plugged into an appropriate outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
WARNING – Improper connection of the equipment-grounding conductor is able to result in a
risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to
whether the product is properly grounded. Do not modify the plug provided with the product – if
it will not fit the outlet, have a proper outlet installed by a qualified electrician.
IAVERTISSEMENT - Une mauvaise connexion du conducteur de mise à la terre de l'équipement peut entraîner un risque de choc électrique. Vérifiez auprès d'un électricien ou d'un
technicien qualifié si vous n'êtes pas sûr que le produit soit correctement mis à la terre. Ne
modifiez pas la fiche fournie avec le produit - si elle ne rentre pas dans la prise, faites installer
une prise appropriée par un électricien qualifié.
11
12
USER MANUAL
USER MANUAL
8.4 Tools and Materials Required
For safe use of electricity, please add circuit breaker protection in the input part
of charging pile. Connect the L1 lead to the grid L1, connect the L2 lead to the grid L2,
Tools required before installing the Wall-Mounted charger, gather the following tools:
connect the PE lead to the grid PE (for all Version).
• Wire stripper
• Crimpers for European terminals
• Phillips screwdriver for M5
• Slotted screwdriver for 4~5.5MM
• Adjustable Wrench M6
• Head gasket screw 10-10.5mm
• Voltmeter or digital multi-meter (for measuring AC voltage at the installation site)
• The inserting cable should meet the best waterproof performance. It is recommended to use
3 core / 7AWG cable (XLPE or equivalent cable) to pull the cable from the distribution box.
• Level ruler
• Pencil or marker
• Machine drill
Installation Instructions
Circuit Breaker Options table
13
Output Amperage (A)
16A
32A
40A
48A
Circuit Breaker Options (A)
20A
40A
50A
60A
“This device shall be mounted at a sufficient height from grade such that the height of the
storage means for the coupling device is located between 600mm (24 inches) and 1.2m (4
feet) from grade.”
14
USER MANUAL
8.5 Wall-Mounted Bracket Installation
USER MANUAL
Step 3: Fix two M5 screws to complete the installation.
Step 1:
• Set the positions of the 4 screw holes and drill them, with a diameter of 8mm and
a depth of 52mm.
• Use 4 sets expansion screw and M6 screw to fix the wall-mounted bracket on the wall.
Overall outlook picture after installation:
Wall-mounted cable winding
Optional cable hanging(optional accessory)
Step 2: Align the rear notch of charger into the wall-mounted bracket and fit the screw
holes of the right and left side.
15
16
USER MANUAL
USER MANUAL
9. Operation Instuctions
Step 3 / Tap the RFID Card
Tap the RFID card to start the charging.
9.1 Operating Procedures
User authorization
Connect to Vehicle Charging Inlet
Charging Message
Charging completed
9.2 Operating Steps
Step 1 / Standby Mode
After power-on, blue light (READY), green light (CHARGE) and red light (FAULT) all lit.
Enter standby mode and the blue light (READY) is steady on.
Step 4 / Charging
The green light (CHARGE) turns to flash automatically, charging is in process.
• If the red light (FAULT) is lit, plug the vehicle connector again.
• If red light is still lit, please refer to "Error and Warning Messages".
READY
CHARGE
Step 2 / Tap the RFID Card
Please plug the charging connector into the vehicle charging inlet. When you tap the
Step 5 / Charging Finished
RFID card first, it needs to complete the insertion of the charging connector within 120
When the charging is finished, the green light (CHARGE) is constantly lit, please
seconds, otherwise you need to tap the RFID card again.
press the button on connector.
17
18
USER MANUAL
USER MANUAL
10. Maintenance and Repair
9.3 Error and Warning Message
10.1 Daily Maintenance
Status
Red
Remark
Input OVP
1 flashes followed by 3 sec pause
Auto Recover
Input UVP
2 flashes followed by 3 sec pause
Auto Recover
Output OCP
3 flashes followed by 3 sec pause
Auto Recover
OTP
4 flashes followed by 3 sec pause
Auto Recover
RCD Abnormal
5 flashes followed by 3 sec pause
Auto Recover
Ground Fault
6 flashes followed by 3 sec pause
Auto Recover
• Please use the charger properly. Do not hit or press hard on the case. If the case is damaged,
Control Pilot Fault
Flicker
Auto Recover
please contact a professional technician.
MCU Self-Test Fail
Constantly Bright
Contact Customer Service
RCD Self-Test Fail
Constantly Bright
Contact Customer Service
Relay Self-Test Fail
Constantly Bright
Contact Customer Service
RCD Abnormal Stop Charging
Constantly Bright
Contact Customer Service
Output OCP Stop Charging
Constantly Bright
Contact Customer Service
warranty period. All warranty services and repairs shall be and performed by certified service
OTP Stop Charging
Constantly Bright
Contact Customer Service
technicians authorized by Joint Technology. For details, please contact your local Joint Tech-
Please keep the charger clean and keep the charge in a clean area with low humidity. Do not
install it in an environment near the sea, with high oil, high humidity or high dust.
• Avoid moisture or water in the charger. If there is water or moisture ingress into the charger, it
is necessary to immediately power off to avoid immediate danger, and notify the professional
personnel to carry out maintenance before next use.
• If there is any damage or dirt on the vehicle connector, charging cable, or vehicle connector
holder, please contact the maintenance personnel immediately.
• Avoid placing the charger near hot objects and at high temperature locations and away from
dangerous substances such as flammable gases and corrosive materials.
• Do not place external objects or heavy objects on the charger to avoid danger.
10.2 Maintenance Spares
• This charger is equipped with maintenance spares for maintenance use during and over the
nology service partner or direct to our Customer Service.
10.3 Warranty and Maintenance
• The warranty period for this charger is three years.
• After the event of any repair or maintenance under the warranty period, if there is no purchase
to extend the warranty service, Joint Technology shall provide a three-month warranty period
for any subsequent paid repair work.
19
20
USER MANUAL
USER MANUAL
• During the warranty period for any malfunction caused by normal use according to the User
Manual and Service Instruction (to be determined by certified maintenance technicians of Joint
Technology), the product shall be repaired free of charge. Except for the following situations,
the charger shall be subject to the above warranty terms:
1. The warranty certificate cannot be provided or the contents of the warranty certificate are
modified or inconsistent with the label indication of the repaired product.
2. Those who are unable to provide valid proof of purchase.
3. Those who exceed the manufacturer's specified warranty period.
4. Those who damage the product due to not following the product service instruction for use,
maintenance and storage.
5. Damage or malfunction caused by foreign object entering.
6. Unauthorized repair, disassembly or modification.
7. Damage caused by force majeure (such as lightning, excessive voltage, earthquake, fire,
flood, etc.).
8. Malfunction and damage caused by other unavoidable external factors. Malfunction and
damage caused by improper use of equipment, such as water or other solutions entering into
the equipment.
9. Malfunction and damage caused by the grid power supply and voltage which is not specified
for use with the charger equipment.
• The above guarantees shall be made solely, and no other express or implied warranties shall
be made (including the implied warranties of merchant ability, particular and applicable reasonableness and adaptability, etc.) whether in the contract, civil negligence, or other aspects, the
Company shall not be responsible for any special, incidental or consequential damages.
21
22
">
