- Baby & children
- Toys & accessories
- Remote controlled toys
- Spektrum
- DX3E DSM 3-Channel Transmitter Only
- Manual
Spektrum DX3E DSM 3-Channel Transmitter Only manual
Add to My manuals17 Pages
Spektrum DX3E, a user-friendly 3-channel radio system, offers versatility and control for your RC adventures. Ideal for beginners and experienced hobbyists alike, it features servo reversing, independent travel adjustment, and a programmable third channel for linear, 2-position, or 3-position settings. Enjoy enhanced precision with steering trim, throttle trim, and dual-rate steering adjustment. The DX3E's reliable 2.4GHz technology provides a strong, interference-free connection, while the battery LED monitor keeps you informed of power levels.
advertisement
®
EN
EN
Table of ConTenTs
Introduction.............................................................................................................................................3
Contents..................................................................................................................................................3
System Features ......................................................................................................................................3
Identifying Controls, Dials and Switches ................................................................................................4
Installing the Batteries .............................................................................................................................5
Using Rechargeable Batteries ..................................................................................................................5
Battery LED Monitor ...............................................................................................................................6
Receiver Compatibility ............................................................................................................................6
Receiver Connection and Installation ......................................................................................................7
Binding a Receiver ..................................................................................................................................7
Failsafe....................................................................................................................................................8
Servo Reversing ......................................................................................................................................8
Auxiliary Settings Linear, 2-Position, 3-Position ....................................................................................9
Travel Adjust ...........................................................................................................................................9
Steering Trim.........................................................................................................................................10
Throttle Trim..........................................................................................................................................10
Steering Rate .........................................................................................................................................11
RF Mode ...............................................................................................................................................11
General Notes .......................................................................................................................................11
Tips on Using 2.4GHz Systems ............................................................................................................12
General Information ..............................................................................................................................13
Warranty Information.............................................................................................................................13
Compliance Information for the European Union ..................................................................................16
Declaration of Conformity .....................................................................................................................16
Instructions for Disposal of WEEE by Users in the European Union .....................................................17
2 SPEKTRUM DX3E USER GUIDE
InTroduCTIon
Spektrum’s DX3E 3-channel radio system features servo reversing and independent travel adjustment on all three channels. In addition the third channel can be programmed as a linear (proportional), 2-position or
3-position channel making it ideal for vehicles with reverse, 2- or 3-speed transmissions or mixture control. The DX3E incorporates Spektrum DSM 2.4GHz technology offering a bulletproof radio link that’s immune to internal (noisy motors/ ESCs, etc.) and external interfering sources. No longer will you have to wait for a frequency or worry about someone else being on the same channel. With Spektrum, when you’re ready to race there’s nothing stopping you!
ConTenTs
The DX3E radio system is supplied with the following:
• DX3E transmitter
• SR300 receiver (SPMSR300)
• 1 S200 servo (SPMS200)
• Bind plug (SPM6802)
• 4 AA alkaline batteries
• 4-cell AA battery holder
• Switch harness
sysTem feaTures
• Dual Rate steering adjustment
• Steering trim
• Throttle trim
• LED battery indicator
• Servo reversing
• Travel adjust
• Selectable linear, 2-position and 3-position
Aux channel
SPEKTRUM DX3E USER GUIDE 3
EN
IdenTIfyIng ConTrols, dIals and swITChes
Antenna
Steering Trim Dial
Battery Indicator
On/Off Switch
Aux. Switch
Bind Indicator
Throttle Trim Dial
Steering Wheel
Steering Rate Dial
Throttle Trigger
Charge Jack
(on back)
Battery Door
(on bottom)
4
ToP Panel
Reverse Switch
Steering
Reverse Switch
Throttle
Reverse Switch
Auxiliary
Bind button
Travel Adjust
Steering Left
Auxiliary Setting
Switch
Travel Adjust
Aux Low
Travel Adjust
Steering Right
Travel Adjust
Throttle Forward
Travel Adjust
Throttle Reverse
Travel Adjust
Aux High
SPEKTRUM DX3E USER GUIDE
InsTallIng The baTTerIes
The DX3E radio system is supplied with 4 AA alkaline batteries required for operation that provide over 16 hours of run time. Many drivers prefer alkaline batteries over rechargeable batteries finding it more convenient to simply replace the batteries when depleted rather than taking the time to recharge.
To install the batteries:
Remove the battery door and install 4 AA batteries observing the polarity marked on the battery holder.
Replace the battery door.
usIng reChargeable baTTerIes
Charger Pigtail for Transmitter
BLACK TO POSITIVE
BLACK W/WHITE STRIPE TO NEGATIVE
Spektrum Transmitter Charge Jack Polarity
-
+
EN
SPEKTRUM DX3E USER GUIDE
Optional NiMH 1.2-volt AA rechargeable batteries
(SPM9525) can also be used. If rechargeable batteries are used, they can be conveniently charged without removing them from the transmitter by using the charge jack located on the back side of the transmitters base.
Use Spektrum’s charger (SPM9526) to charge rechargeable batteries in the DX3E.
IMPORTANT: All Spektrum charge jacks are center-pin negative. This is opposite of many chargers. Before using a charger, make sure the connector is center-pin negative. This can be done using a voltmeter. Also, unlike conventional radio systems that use 8 cells to power the transmitter, the DX3E uses 4 cells.
This is due to the electronics being more efficient. When charging, be sure to use a charger designed for 4 cells (a 4.8-volt battery pack) when charging the transmitter. Many drivers simply make a harness and use the same charger used to charge their car packs but turn the current rate down to 1 to 2 amps.
Warning: Charge only rechargeable batteries. Nonrechargeable batteries may burst causing injury to persons and/or damage to property.
5
EN
baTTery led monITor
A green LED battery monitor is located on the front left of the transmitter next to the on/off switch. When the battery voltage is above 5 volts the LED will be solid green indicating that the battery has sufficient operational voltage. Below 5 volts the green LED will begin to dim, indicating the battery is low. When the voltage drops below 4 volts, the green LED will turn off and only the red LED will be lit, indicating the batteries should be replaced immediately.
reCeIver ComPaTIbIlITy
The DX3E features DSM technology and is compatible with Spektrum DSM and DSM2 surface receivers and the marine receiver.
ComPaTIble sPekTrum reCeIvers
The DX3E is compatible with the following receivers.
Note: The DX3E operates in 16.5ms frame rate.
DSM
SR300 - 3-channel Sport - SPMSR300
SR3001 - 3-channel Pro - SPM1205
SR3300T - 3-channel with built-in telemetry - SPMSR3300T
SR3500 - 3-channel Micro Race - SPM1210
Note: The SR3000HRS (SPM1202) receiver is designed to be used with Spektrum’s Futaba
HRS compatible module system only and is not compatible with the DX3E.
DSM2
SR3100 - 3-channel Pro - SPMSR3100
SR3520 - 3-channel Micro Pro - SPMSR3520
Solid Green - Battery is good
Dim Green - Battery voltage is low
No Green, only Solid Red - Battery voltage is critically
low. Replace batteries
oPTIonal rubber grIPs
The DX3E is supplied with a medium-size grip installed on the transmitter. Optional small and large grips are available (SPM9006) to fit preferences and hand sizes.
Each grip’s size is identified with an “S” (small), “M”
(medium), or “L” (large) on the inside of the grip for easy identification. To remove, simply lift the edge of the grip and continue around the grip until it is completely removed. To replace, align the tabs of the grip to the slots in the handle and press the grip in place.
Marine
MR3000 - 3-channel Marine - SPMMR3000
6
Please note that DSM2 and marine compatible transmitters can be identified by the following logo located on the back of the transmitter:
SPEKTRUM DX3E USER GUIDE
reCeIver ConneCTIon and
InsTallaTIon
Typical Electric Installation
7.2V Battery
To Motor
bIndIng a reCeIver
1. With the receiver off insert the bind plug into the BND port on the receiver.
2. Power the receiver through any other port. The amber
LED will flash continuously, indicating the receiver is in bind mode.
3. With the steering wheel, throttle trigger and Aux channel (if applicable) in the desired preset failsafe positions, press and hold the bind button and turn on the transmitter. The red LED on the front of the transmitter will flash within a couple seconds indicating the transmitter is in bind mode. Once the red LED begins flashing, release the bind button.
Bind Plug LED
Receiver
DSM™:: 2.4Ghz
SR300
Electronic
Speed Control
Servo
Receiver
DSM™:: 2.4Ghz
SR300
Rx
SURFACE USE ONLY
©2009 Horizon Hobby, Inc.
AUX
THR
STR
BAT/TEL
Typical Gas Installation
Throttle Servo
Steering Servo
6V Battery
4. Within 15 seconds, the LED on the receiver will go solid indicating a successful bind has taken place.
5. Remove the bind plug and store it in a convenient place.
Note: You must rebind when:
• Different failsafe positions are desired, e.g. when throttle or steering reversing has been changed.
• Changing receiver types, e.g. changing from a DSM receiver to a DSM2 or Marine receiver.
• The receiver is to be bound to a different transmitter.
Note: Some Spektrum receivers, like the SR3000, use a bind button rather than a bind plug. The binding process is the same with this receiver; however, instead of inserting the plug before powering up the receiver, press and hold the bind button while powering up the receiver to enter bind mode.
LED
EN
Bind Plug
SPEKTRUM DX3E USER GUIDE 7
EN
faIlsafe
Failsafe positions are also set during binding. In the unlikely event that the radio link is lost during use, the receiver will drive the servos to their preprogrammed failsafe positions (normally full brakes and straight steering). If the SR300 receiver is turned on prior to turning on the transmitter, the receiver will enter the failsafe mode, driving the servos to their preset failsafe positions. When the transmitter is turned on, normal control is resumed. Failsafe servo positions are set during binding (see Bind on the previous page).
servo reversIng
Servo reversing is used to reverse the direction of the output of each channel. (e.g., a right steering command results in the wheels turning right). To reverse a channel, switch the position of the correlating switch. “N” is for normal. “R” is for reverse. A small screwdriver can be used to move the switch if necessary.
Reverse Switch
Steering
Reverse Switch
Throttle
Reverse Switch
Auxiliary
8 SPEKTRUM DX3E USER GUIDE
auxIlIary seTTIngs lInear,
2-PosITIon, 3-PosITIon
The Auxiliary channel can be selected to operate in three different methods:
2-Position (2P) - The servo travels to its opposite endpoints when the auxiliary button is pressed. Ideal for forward and reverse transmissions and some two speed transmissions.
3-Position (3P) - The servo travels from endpoint to center to the opposite endpoint when the auxiliary button is pressed. Used for forward, neutral and reverse transmissions and some 3-speed transmissions.
Linear (LIN) - This allows the servo position to be controlled proportionately. Ideal for mixture control on engines.
Auxiliary Setting
Switch
Travel adJusT
Travel adjust is used to limit the maximum travel that each channel will travel in each direction. Travel adjust is independently adjustable in each direction. To reduce the maximum travel in each direction, use your finger or a small screwdriver to rotate the corresponding travel adjust dial counterclockwise. To increase travel in each direction, rotate the corresponding dial clockwise.
Travel Adjust
Steering Left
Travel Adjust
Throttle Forward
Travel Adjust
Steering Right
Travel Adjust
Aux High
Travel Adjust
Throttle Reverse
Travel Adjust
Aux Low
EN
Note that the servo reversing and travel adjust functions are used to adjust the endpoints and direction of the auxiliary channel.
SPEKTRUM DX3E USER GUIDE 9
EN
sTeerIng TrIm
The steering trim dial is used to adjust the steering trim when the wheel is centered. Rotating the dial causes the steering trim (the steering at rest position) to be changed.
Normally steering trim is adjusted until the car tracks straight.
Steering Trim Dial
ThroTTle TrIm
The throttle trim dial is used to adjust the throttle trim when the throttle stick is released (neutral position).
This is typically used to adjust the brakes. Rotating the dial causes the throttle trim (the throttle position at rest) to be changed.
Throttle Trim Dial
10 SPEKTRUM DX3E USER GUIDE
sTeerIng raTe
Steering rate (also known as dual rate) allows on-the-fly steering travel adjustments to be made using the steering rate dial. Steering rate limits the amount of travel of the steering servo. The steering rate cannot be greater than
100% and will never exceed the amount of steering travel set with the travel adjust dials.
Steering Rate Dial
rf mode
The DX3E features an RF mode switch on the bottom side of the transmitter near the trigger. Std is the standard RF mode. FR is the France RF mode and should only be selected if the transmitter is used in France.
general noTes
Radio controlled models are a great source of pleasure.
Unfortunately, they can also pose a potential hazard if not operated and maintained properly. It is imperative to install your radio control system correctly. Additionally, your level of operating competency must be high enough to ensure you are able to control your model under all conditions. If you are a newcomer to radio controlled models, please seek help from an experienced modeler or your local hobby shop.
Safety Points to Obey for Modelers
• Ensure your batteries (both transmitter and receiver) have been properly charged for your model.
• Check all servos and their connections prior to each run.
• Do not operate your model near spectators, parking areas or any other area that could result in injury to people or damage of property.
• Do not operate your model during adverse weather conditions. Poor visibility can cause disorientation and loss of control of your model.
• Do not point the transmitter antenna directly toward the model. The radiation pattern from the tip of the antenna is inherently low.
• Do not take chances. If at any time during the operation of your model you observe any erratic or abnormal operation, immediately stop operation of your model until the cause of the problem has been ascertained and corrected. Safety can never be taken lightly.
EN
SPEKTRUM DX3E USER GUIDE 11
EN
TIPs on usIng 2.4ghz sysTems
Your DSM equipped 2.4GHz system is intuitive to operate, functioning nearly identically to FM systems.
Following are a few common questions from customers.
1. Q: Which do I turn on first, the transmitter or the receiver?
A: It doesn’t matter, although it is suggested to turn the transmitter on first. If the receiver is turned on first, all channels will be driven to the failsafe position set during binding. When the transmitter is then turned on the transmitter scans the 2.4GHz band and acquires an open channel. Then the receiver that was previously bound to the transmitter scans the band and finds the GUID (Globally Unique Identifier code) stored during binding. The system then connects and operates normally. If the transmitter is turned on first, the transmitter scans the 2.4GHz band and acquires an open channel. When the receiver is turned on, the receiver scans the 2.4GHz band looking for the previously stored GUID. When it locates the specific
GUID code and confirms uncorrupted repeatable packet information, the system connects and normal operation takes place. Typically this takes 2 to 6 seconds.
2. Q: Sometimes the system takes longer to connect and sometimes it doesn’t connect at all. Why?
A In order for the system to connect (after the receiver is bound), the receiver must receive a large number of continuous (one after the other) uninterrupted perfect packets from the transmitter. This process is purposely critical of the environment ensuring that it’s safe to fly when the system does connect. If the transmitter is too close to the receiver (less than 4 feet) or if the transmitter is located near metal objects
(inside or around a pit trailer, metal transmitter case, the bed of a truck, the top of a metal work bench, etc.) connection will take longer. In some cases connection will not occur as the system is receiving reflected 2.4GHz energy from itself and is interpreting this as unfriendly noise. Moving the system away from metal objects or moving the transmitter away from the receiver and powering the system up again will cause a connection to occur. This only happens during the initial connection. Once connected the system is locked, and should a loss of signal occur
(failsafe), the system connects immediately (4ms) when signal is regained.
3. Q: I’ve heard that the DSM system is less tolerant of low voltage. Is this correct?
A: All DSM receivers have an operational voltage range of 3.5 to 9 volts. With most systems this is not a problem as in fact most servos cease to operate at around 3.8 volts. When using multiple high-current draw servos with a single or inadequate battery/ power source, heavy momentary loads can cause the voltage to dip below this 3.5-volt threshold causing the entire system (servos and receiver) to brown out. When the voltage drops below the low voltage threshold (3.5 volts), the DSM receiver must reboot
(go through the start up process of scanning the band and finding the transmitter) and this can take several seconds.
4. Q: Sometimes my receiver loses its bind and won’t connect, requiring rebinding. What happens if the bind is lost in use?
A: The receiver will never lose its bind unless it’s instructed to. It’s important to understand that during the binding process the receiver not only learns the
GUID (code) of the transmitter but the transmitter learns and stores the type of receiver that it’s bound to.
If the system fails to connect, the following more than likely may have occurred:
• The transmitter is near conductive material
(transmitter case, truck bed, etc.) and the reflected
2.4GHz energy is preventing the system from connecting. (See #2 on this page)
12 SPEKTRUM DX3E USER GUIDE
general InformaTIon fCC Information
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This product contains a radio transmitter with wireless technology which has been tested and found to be compliant with the applicable regulations governing a radio transmitter in the 2.400GHz to 2.4835GHz frequency range.
Antenna Separation Distance
When operating your Spektrum transmitter, please be sure to maintain a separation distance of at least 5 cm between your body (excluding fingers, hands, wrists, ankles and feet) and the antenna to meet RF exposure safety requirements as determined by FCC regulations.
The illustrations below show the approximate 5 cm RF exposure area and typical hand placement when operating your Spektrum transmitter.
warranTy InformaTIon warranty Period
Exclusive Warranty- Horizon Hobby, Inc., (Horizon) warranties that the Products purchased (the “Product”) will be free from defects in materials and workmanship for a period of 1 year from the date of purchase by the
Purchaser.
1 year limited warranty
(a) This warranty is limited to the original Purchaser
(“Purchaser”) and is not transferable. REPAIR OR
REPLACEMENT AS PROVIDED UNDER THIS WARRANTY
IS THE EXCLUSIVE REMEDY OF THE PURCHASER. This warranty covers only those Products purchased from an authorized Horizon dealer. Third party transactions are not covered by this warranty. Proof of purchase is required for warranty claims. Further, Horizon reserves the right to change or modify this warranty without notice and disclaims all other warranties, express or implied.
(b) Limitations- HORIZON MAKES NO WARRANTY OR
REPRESENTATION, EXPRESS OR IMPLIED, ABOUT
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE OF THE PRODUCT.
THE PURCHASER ACKNOWLEDGES THAT THEY
ALONE HAVE DETERMINED THAT THE PRODUCT
WILL SUITABLY MEET THE REQUIREMENTS OF THE
PURCHASER’S INTENDED USE.
(c) Purchaser Remedy- Horizon’s sole obligation hereunder shall be that Horizon will, at its option, (i) repair or (ii) replace, any Product determined by Horizon to be defective. In the event of a defect, these are the
Purchaser’s exclusive remedies. Horizon reserves the right to inspect any and all equipment involved in a warranty claim. Repair or replacement decisions are at the sole discretion of Horizon. This warranty does not cover cosmetic damage or damage due to acts of
God, accident, misuse, abuse, negligence, commercial use, or modification of or to any part of the Product.
This warranty does not cover damage due to improper installation, operation, maintenance, or attempted repair by anyone other than Horizon. Return of any goods by
Purchaser must be approved in writing by Horizon before shipment.
EN
SPEKTRUM DX3E USER GUIDE 13
EN
damage limits
HORIZON SHALL NOT BE LIABLE FOR SPECIAL,
INDIRECT OR CONSEQUENTIAL DAMAGES, LOSS OF
PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN
ANY WAY CONNECTED WITH THE PRODUCT, WHETHER
SUCH CLAIM IS BASED IN CONTRACT, WARRANTY,
NEGLIGENCE, OR STRICT LIABILITY. Further, in no event shall the liability of Horizon exceed the individual price of the Product on which liability is asserted. As Horizon has no control over use, setup, final assembly, modification or misuse, no liability shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly, the user accepts all resulting liability.
If you as the Purchaser or user are not prepared to accept the liability associated with the use of this Product, you are advised to return this Product immediately in new and unused condition to the place of purchase.
Law: These Terms are governed by Illinois law (without regard to conflict of law principals).
safety Precautions
This is a sophisticated hobby Product and not a toy.
It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage to the Product or other property. This Product is not intended for use by children without direct adult supervision. The Product manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or injury.
Questions, assistance and repairs
Your local hobby store and/or place of purchase cannot provide warranty support or repair. Once assembly, setup or use of the Product has been started, you must contact
Horizon directly. This will enable Horizon to better answer your questions and service you in the event that you may need any assistance. For questions or assistance, please direct your email to productsupport@horizonhobby.
com, or call 877.504.0233 toll free to speak to a product support representative.
Inspection or repairs
If this Product needs to be inspected or repaired, please call for a Return Merchandise Authorization (RMA). Pack
14 the Product securely using a shipping carton. Please note that original boxes may be included, but are not designed to withstand the rigors of shipping without additional protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is not responsible for merchandise until it arrives
and is accepted at our facility. A Service Repair
Request is available at www.horizonhobby.com on the
“Support” tab. If you do not have internet access, please include a letter with your complete name, street address, email address and phone number where you can be reached during business days, your RMA number, a list of the included items, method of payment for any nonwarranty expenses and a brief summary of the problem.
Your original sales receipt must also be included for warranty consideration. Be sure your name, address, and
RMA number are clearly written on the outside of the shipping carton.
warranty Inspection and repairs
To receive warranty service, you must include
your original sales receipt verifying the proof-ofpurchase date. Provided warranty conditions have been met, your Product will be repaired or replaced free of charge. Repair or replacement decisions are at the sole discretion of Horizon Hobby.
non-warranty repairs
Should your repair not be covered by warranty the repair will be completed and payment will be required without notification or estimate of the expense unless the expense exceeds 50% of
the retail purchase cost. By submitting the item for repair you are agreeing to payment of the repair without notification. Repair estimates are available upon request.
You must include this request with your repair. Nonwarranty repair estimates will be billed a minimum of
½ hour of labor. In addition you will be billed for return freight. Please advise us of your preferred method of payment. Horizon accepts money orders and cashiers checks, as well as Visa, MasterCard, American Express, and Discover cards.
If you choose to pay by credit card, please include your credit card number and expiration date. Any repair left unpaid or unclaimed after 90 days will be considered abandoned and will be disposed of accordingly.
Please note: non-warranty repair is only available on electronics and model engines.
SPEKTRUM DX3E USER GUIDE
United States
Electronics and engines requiring inspection or repair should be shipped to the following address:
Horizon Service Center
4105 Fieldstone Road
Champaign, Illinois 61822 USA
All other products requiring warranty inspection or repair should be shipped to the following address:
Horizon Support Team
4105 Fieldstone Road
Champaign, Illinois 61822 USA
Please call 877.504.0233 or e-mail us at [email protected] with any questions or concerns regarding this product or warranty.
United Kingdom
Electronics and engines requiring inspection or repair should be shipped to the following address:
Horizon Hobby UK
Units 1-4 Ployters Rd
Staple Tye
Harlow, Essex
CM18 7NS
United Kingdom
Please call +44 (0) 1279 641 097 or email us at [email protected] with any questions or concerns regarding this product or warranty.
Germany
Electronics and engines requiring inspection or repair should be shipped to the following address:
Horizon Technischer Service
Hamburger Str. 10
25335 Elmshorn
Germany
Please call +49 4121 46199 66 or email us at [email protected] with any questions or concerns regarding this product or warranty.
France
Horizon Hobby SAS
14 Rue Gustave Eiffel
Zone d’Activité du Réveil Matin
91230 Montgeron
France
Please call +33 (0) 1 60 47 44 47 with any questions or concerns regarding this product or warranty.
SPEKTRUM DX3E USER GUIDE 15
EN
EN
Compliance Information for the European Union
The associated regulatory agencies of the following countries recognize the noted certifications for this product as authorized for sale and use:
Declaration of Conformity
(in accordance with ISO/IEC 17050-1)
No. HH20090712
Product(s):
Item Number(s):
Equipment class:
Spektrum DX3E Surface Radio (International)
SPM3160E
2
The objects of declaration described above are in conformity with the requirements of the specifications listed below, following the provisions of the European R&TTE directive 1999/5/EC:
EN 60950
EN 300-328- V1.7.1
EN 301 489-1 v.1.6.1
EN 301 489-17 v.1.2.1
Safety
ERM requirements for wideband transmission systems operating in the 2.4
GHz ISM band
General EMC requirements for Radio equipment
Signed for and on behalf of:
Horizon Hobby, Inc.
Champaign, IL USA
July. 12, 2009
Steven A. Hall
Vice President
International Operations and Risk Management
Horizon Hobby, Inc.
Instructions for Disposal of WEEE by Users in the European Union
This product must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of their waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment.
The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or where you purchased the product.
16 SPEKTRUM DX3E USER GUIDE
®
www.horizonhobby.com www.spektrumrc.com
©2010 Horizon Hobby, Inc.
DSM and DSM2 are trademarks or registered trademarks of Horizon Hobby, Inc.
The Spektrum trademark is used with permission of Bachmann Industries, Inc.
Spektrum radios and accessories are exclusively available from Horizon Hobby, Inc.
US Patent 7,391.320. Other patents pending.
Revised 10/2010 15697.5i
advertisement
Related manuals
advertisement
Table of contents
- 3 Introduction
- 3 System Features
- 4 Identifying Controls, Dials and Switches
- 5 Installing the Batteries
- 5 Using Rechargeable Batteries
- 6 Battery LED Monitor
- 6 Receiver Compatibility
- 7 Receiver Connection and Installation
- 7 Binding a Receiver
- 8 Failsafe
- 8 Servo Reversing
- 9 Auxiliary Settings Linear, 2-Position, 3-Position
- 9 Travel Adjust
- 10 Steering Trim
- 10 Throttle Trim
- 11 Steering Rate
- 11 RF Mode
- 11 General Notes
- 12 Tips on Using 2.4GHz Systems
- 13 General Information
- 13 Warranty Information
- 16 Compliance Information for the European Union
- 16 Declaration of Conformity
- 17 Instructions for Disposal of WEEE by Users in the European Union