advertisement
External & Internal
Connections
HIM Overview
Topic
External & Internal Connections
Viewing and Editing Parameters
Page
The PowerFlex 700 provides a number of cable connection points.
Figure 2 - Port Locations - Frames 0…6 (0 Frame shown).
U/T1
V/T2
W/T3
R/L1
S/L2
T/L3
BR1
BR2
DC+
DC–
PE
!
DANGER
Use 75C Wire Only
#10-#14 AWG
Torque to 7 in-lbs
Optional
Communications
Module
1
4
2
3
2
2
3
No.
Connector
1
DPI Port 1
4
DPI Port 2
DPI Port 3 or 2
DPI Port 5
Description
HIM connection when installed in cover.
Cable connection for handheld and remote options.
Splitter cable connected to DPI Port 2 provides additional port.
Cable connection for communications adapter.
Appendix
B
Rockwell Automation Publication 20B-UM002G-EN-P - July 2014
101
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 3 New and Updated Information
- 3 Manual Updates
- 9 Who Should Use this Manual?
- 9 What Is Not in this Manual
- 9 Manual Conventions
- 10 Additional Resources
- 10 ATEX Approved Drives & Motors
- 10 Drive Frame Sizes
- 11 General Precautions
- 13 Catalog Number Explanation
- 15 About Parameters
- 17 How Parameters are Organized
- 17 Numbered List View
- 18 Basic Parameter View
- 19 Advanced Parameter View
- 21 Monitor File
- 23 Motor Control File
- 29 Speed Command File
- 38 Dynamic Control File
- 44 Utility File
- 55 Communication File
- 59 Inputs & Outputs File
- 67 Applications File
- 72 Pos/Spd Profile File
- 77 Parameter Cross Reference – by Name
- 80 Parameter Cross Reference – by Number
- 83 Faults and Alarms
- 84 Drive Status
- 84 Front Panel LED Indications
- 85 Precharge Board LED Indications
- 85 HIM Indication
- 85 Manually Clearing Faults
- 86 Fault Descriptions
- 90 Clearing Alarms
- 91 Alarm Descriptions
- 94 Common Symptoms/ Corrective Actions
- 96 Testpoint C odes and Functions
- 97 Communication Configurations
- 97 Typical Programmable Controller Configurations
- 101 External & Internal Connections
- 102 Removing/Installing the HIM
- 103 Disconnecting the HIM
- 103 Reconnecting the HIM
- 104 Menu Structure
- 105 Diagnostics Menu
- 105 Parameter Menu
- 105 Device Select Menu
- 105 Memory Storage Menu
- 105 Start Up Menu
- 105 Preferences Menu
- 106 Viewing and Editing Parameters
- 106 LCD HIM
- 107 Linking Parameters
- 107 Establishing A Link
- 109 Adjustable Voltage Operation
- 110 Enabling Adjustable Voltage
- 111 External Brake Resistor
- 111 Hand-Off-Auto (HOA)
- 111 Lifting/Torque Proving
- 113 TorqProve Manual Start Up
- 115 Drive Setup
- 116 Installation/Wiring
- 116 Lifting/Torque Proving Application Programming
- 118 Limit Switches for Digital Inputs
- 119 Minimum Speed
- 120 Motor Control Technology
- 120 Torque Producers
- 120 Torque Controllers
- 121 Speed Regulators
- 121 Motor DC Injection
- 122 Motor Overload
- 123 Motor Overload Memory Retention Per 2005 NEC
- 123 Overspeed
- 124 Position Indexer/Speed Profiler
- 124 Common Guidelines for all Step Types
- 125 Position Loop Tuning
- 125 Profile Command Control Word
- 126 Velocity Regulated Step Types and Parameters
- 127 Position Regulated Step Types and Parameters
- 128 Homing Routine
- 130 Example 1: Five Step Velocity Profile (Time-Based and Encoder- Based)
- 131 Example 2: Six Step Velocity Profile (Digital Input-Based)
- 132 Example 3: Five Step Positioner with Incremental Encoder
- 133 Power Loss Ride Through
- 134 Process PID
- 134 PI Enable
- 136 Reverse Speed Limit
- 137 Skip Frequency
- 138 Sleep Wake Mode
- 139 Definitions
- 140 Start At PowerUp
- 140 Stop Mode
- 141 Configuration
- 145 Stop Dwell Time
- 146 Voltage Tolerance
- 148 Motor Requirements
- 148 Drive Wiring
- 149 Drive Configuration
- 149 Hardware
- 149 Firmware
- 150 Start-Up & Periodic Drive Testing Requirement
- 150 Preparation
- 151 Test