Installing the two-piece bezel. IBM IntelliStation Z Pro 9232, IntelliStation Z Pro Type 9228, 9228 - IntelliStation Z - Pro
Add to My manuals184 Pages
advertisement
Installing the two-piece bezel
To install the two-piece bezel, complete the following steps.
Bezel clips
Figure 12. Installing the upper bezel
1. Install the upper bezel on the front of the computer chassis: a. Insert the two right-side tabs on the upper bezel into the matching holes on the right side of the chassis.
b. Rotate the upper bezel to the left side of the chassis and press the bezel clips into the matching indentations on the left side of the chassis until the bezel clips snap into place.
2. Install the lower bezel on the front of the computer.
Chapter 4. Removing and replacing computer components
35
Figure 13. Installing the lower bezel
a. Insert the two bottom tabs on the lower bezel into the matching holes in the front of the chassis.
b. Tilt the top of the lower bezel into position on the chassis until the lower bezel locks securely into place.
3. Reconnect the external cables and power cords; then, turn on the attached devices and the computer.
Removing an adapter
This section describes the removal of adapters in the PCI Express slots, PCI-X slots 4 and 5, and PCI slot 6.
To remove an adapter, complete the following steps.
Rear adapterretention bracket
Expansionslot cover
Figure 14. Removing an adapter
Adapter
Front adapterretention bracket
1. Read the safety information that begins on page vii and “Installation guidelines” on page 29.
2. Turn off the computer and all attached devices; then, disconnect all external cables and power cords.
3. Remove the side cover (see “Removing the side cover” on page 31).
4. Disconnect any cables to the adapter or any cables that impede access to the adapter.
5. For full-length adapters, rotate the rear adapter-retention bracket to the fully open (unlocked) position. Press the two blue release buttons located on the side of the front adapter-retention bracket that faces the adapters. If you are removing a smaller adapter, rotate only the rear adapter-retention bracket.
36
IBM IntelliStation Z Pro Type 9228 and 9232: Problem Determination and Service Guide
advertisement
Related manuals
advertisement
Table of contents
- 19 Related documentation
- 20 Notices and statements in this document
- 21 Features and specifications
- 22 Controls, LEDs, and connectors
- 22 Front view
- 23 Rear view
- 26 Internal LEDs, connectors, and jumpers
- 26 System board option connectors
- 28 System board external connectors
- 29 System board LEDs
- 30 System board jumpers
- 31 Updating the firmware
- 31 Configuring the computer
- 32 Starting the Configuration/Setup Utility program
- 32 Using the Boot Menu program
- 33 Enabling the Broadcom NetXtreme Gigabit Ethernet Boot Agent
- 33 LSI Logic Configuration Utility program
- 38 Replaceable computer components
- 41 Keyboards (USB)
- 43 Product recovery CDs
- 44 Power cords
- 48 System reliability guidelines
- 48 Handling static-sensitive devices
- 49 Returning a device or component
- 49 Removing and replacing consumable parts and Tier 1 CRUs
- 49 Removing the side cover
- 50 Installing the side cover
- 51 Removing the two-piece bezel
- 53 Installing the two-piece bezel
- 55 Installing an adapter
- 58 Installing the hard drive backplate
- 60 Installing a DIMM
- 63 Installing the battery
- 65 Removing the internal speaker
- 66 Removing and installing internal drives
- 72 Removing the hard disk drive fan
- 75 Removing the rear fan
- 77 Removing the expansion slot fan
- 78 Installing the expansion slot fan
- 80 Installing the mini-PCI Express adapter
- 82 Installing the power switch/LED assembly
- 83 Removing the front card/bracket assembly
- 84 Installing the front card/bracket assembly
- 85 Removing and replacing FRUs
- 85 Removing the front adapter-retention bracket
- 86 Installing the front adapter-retention bracket
- 87 Removing the rear adapter-retention bracket
- 88 Installing the rear adapter-retention bracket
- 91 Installing the DIMM fan assembly
- 95 Installing the microprocessor and fan sink
- 98 Removing the power supply
- 102 Removing the system board
- 111 Error logs
- 112 POST error codes
- 126 CD or DVD drive problems
- 127 Diskette drive problems
- 127 General problems
- 128 Hard disk drive problems
- 128 Intermittent problems
- 129 Keyboard, mouse, or pointing-device problems
- 130 Memory problems
- 130 Microprocessor problems
- 130 Monitor or video problems
- 133 Power problems
- 134 Printer problems
- 135 Software problems
- 135 USB port problems
- 137 Error LEDs
- 138 Power-supply LEDs
- 140 Running the diagnostic programs
- 142 Viewing the test logs
- 150 Creating an IBM Enhanced Diagnostics diskette or CD
- 154 Emergency recovery-repair diskettes (Windows)
- 154 Creating an emergency recovery-repair diskette in Windows
- 155 Using the recovery-repair diskette in Windows
- 155 Recovering the operating system and preinstalled software
- 155 Recovering the operating system
- 156 Recovering or installing device drivers
- 158 Interrupt status port register error procedures
- 160 ServeRAID error codes
- 163 Erasing a lost or forgotten password (clearing CMOS)
- 164 Solving power problems
- 164 Solving undetermined problems
- 165 Problem determinations tips
- 167 Using the documentation
- 168 Software service and support
- 168 Hardware service and support
- 170 Trademarks
- 170 Important notes
- 174 Electronic emission notices
- 175 Industry Canada Class B emission compliance statement
- 175 Avis de conformité à la réglementation d’Industrie Canada
- 175 European Union EMC Directive conformance statement
- 175 Notice for South Korea and translations (MIC)