- Home
- Domestic appliances
- Large home appliances
- High-pressure cleaners
- Campbell Hausfeld
- PW167600AV
- User manual
Installation Instructions. Campbell Hausfeld CAMPBELL PW167600AV, PW167600AV
Add to my manuals
24 Pages
advertisement
PW167600AV
Injection hazard.
● Keep clear of nozzle. NEVER direct high pressure spray at any person, animal or self.
● Always wear safety glasses or goggles and protective clothing.
Explosion hazard.
● NEVER spray flammable liquids or use pressure washer in areas containing combustible dust, liquids or vapors.
Equipment damage.
● ALWAYS turn water supply “ON” before turning pressure washer
“ON”. Running pump dry causes serious damage.
● NEVER allow the unit to run with the trigger released (off) for more than one minute. Resulting heat buildup will damage pump.
● NEVER store the pressure washer outdoors or where it could freeze.
The pump will be seriously damaged.
● Release the trigger when changing from high to low pressure modes.
Failure to do so could result in damage to the nozzle.
● If an extension cord is needed, the appropriate wire sizes must be used
(See chart).
Extension
Cord size
14 AWG
12 AWG
Allowable length
25’
Yes
Yes
50’
No
Yes
● This unit must always be used in the horizontal position.
EXTENSION CORDS
If using an extension cord, use only grounded, three wire extension cords that are in good condition.
Use only extension cords that are intended for outdoor use. These extension cords are identified by a marking
“Acceptable for use with outdoor appliances; store indoors while not in use”.
Use only extension cords having an electrical rating not less than the rating of the product.
Do not use damaged extension cords.
Examine extension cord before using and replace if damaged. Do not abuse extension cord and do not pull on the cord to disconnect. Keep cord away from heat and sharp edges. Always disconnect the cord from the receptacle before disconnecting the product from the extension cord.
Note: Do not use 16 or 18 AWG extension cords on this product.
Installation
Instructions
Tools Required for Installation:
● Flat Screwdriver
● Hammer/Mallet
● Adjustable Wrench
1. Set plastic spacer (included in parts pack) on workbench (Figure 1).
Figure 1
2. Place “star shaped” retaining ring on the spacer (tangs pointing down)
(Figure 2).
Figure 2
3. Tap the retaining ring onto the axle
(Figure 3 & 4).
Figure 3
Figure 4
4. Put both wheels on axle, solid sides together (Figure 5).
Figure 5
5. Attach opposite ring in the same manner (Figure 6).
Figure 6
6. Slide wheels out and snap axle into place on the underside of body
(Figure 7).
7. Snap wheel covers on the wheel.
8. Attach foot to front of pressure washer body (Figure 7).
Figure 7
9. Hook up chemical suction hose to the tip on the bottom of the handle
(Figure 8).
Figure 8
10. Attach black handle with enclosed screws and washers (Figure 9).
Figure 9
3
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 2 Specifications
- 3 Installation Instructions
- 4 Setup, Operating and Maintenance Instructions
- 5 Troubleshooting Chart
- 6 Replacement Parts List
- 7 Warranty
- 10 Spécifications
- 11 Information de Sécurité et Avertissements
- 11 Instructions d’Installation
- 12 Instructions de Montage, d’Opération et d’Entretien
- 13 Guide de Dépannage
- 14 Liste de Pièces de Rechange
- 15 Garantie
- 18 Especificaciones
- 20 Instrucciones para la Instalación
- 21 Instrucciones para conectar, operar y darle mantenimiento
- 21 Guía de Diagnóstico de Averías
- 22 Lista de Repuestos
- 23 Garantía