advertisement
Programming
You can change the programming of your cooktop (see chart). You can change several settings one after the other.
After starting the programming function P (Program), an S
(Status) will appear in the timer display. With cooktops that have 3 cooking zones, an additional display appears at the back left.
The program is displayed in the front left and back left cooking zone displays. Example:
Program 03 = front left 0, back left 3
Program 14 = front left 1, back left 4
The status is displayed in the front right cooking zone display.
When programming is completed, a reset is carried out automatically. This is completed when the indicator above the s sensor comes on briefly.
Do not switch the cooktop on again until reset is completed.
Starting the programming function
^ With the cooktop switched off, touch the s and $ sensors
at the same time until the Lock indicator flashes.
Selecting the program
^ To set the ones, touch the sensor for the back left cooking zone followed by the respective number on the settings bar.
^ To set the tens, touch the sensor for the front left cooking zone followed by the respective number on the settings bar.
Setting the status
^ Touch the sensor for the front right cooking zone followed by the respective number on the settings bar.
46
Programming
Saving the settings
^ Touch the s sensor until the displays go out.
If you do not want to save the settings
^ Touch the $ sensor until the displays go out.
47
Programming
Program*
P 00 Demo mode and factory
P
P
P
P default settings
02 Number of power levels
03 Induction warning tone when there is no or unsuitable cookware.
04 Keypad tone when a sensor is touched
05 Timer tone
S 0
S 1
S 2
S 3
S 0
S 1
S 2
S 3
Status** Setting
S 0
S 1
Demo mode ON
(after switching the cooking zone on dE appears in the timer display for several seconds)
Demo mode Off
S 9
S 0
S 1
Factory default settings restored
9 power levels
(1, 2, 3 ... to 9)
17 power levels
(1, 1., 2, 2., 3 ... to 9)
If Auto heat-up is selected:
A will flash alternately with the continued-cooking setting.
S 0
S 1
S 2
S 3
Off
Quiet
Medium
Loud
Off
Quiet
Medium
Loud
Off
Quiet, 10 seconds
Medium, 10 seconds
Loud, 10 seconds
* Programs not listed here are not available.
** The factory default settings are shown in bold.
48
Programming
Program*
P
P
06
07
Safety lock
System lock
P 08 Auto heat-up S 0
S 1
P 10 Miele
|home
- only on communication-enabled appliances retrofitted with a communication module -
P 16 Sensor reaction speed
S
S
S
P 15 Audible tone if the sensor areas are covered
S 0
S 1
S
0
1
2
0
S 1
S 2
Status** Setting
S 0 One-finger locking using
$
S 1 Three-finger locking by touching
$ and the sensors for the two right-hand cooking zones at the same time
S 0 Only manual activation of the system lock
S 1 Manual and automatic activation of the system lock
Off
On
Feature not available deregistered registered
Off
On
Slow
Normal
Fast
* Programs not listed here are not available.
** The factory default settings are shown in bold.
49
advertisement
Related manuals
advertisement
Table of contents
- 4 Guide to the cooktop
- 4 Cooktop models
- 6 Control panel
- 8 Cooking zone data
- 8 Special accessories
- 9 Safety instructions and warnings
- 18 Help protect our environment
- 19 Before the first use
- 19 First cleaning
- 19 First use
- 20 Induction
- 20 How induction works
- 21 Noises
- 22 Cookware
- 23 Use
- 23 The basics of use
- 24 Switching on
- 25 Power settings
- 26 Auto heat-up
- 28 Booster Function
- 30 Keeping warm
- 31 Switching off and residual heat display
- 32 Tips for saving energy
- 33 Timer
- 34 Minute minder
- 37 Switching a cooking zone off automatically
- 38 Using both timer functions at the same time
- 39 Safety features
- 39 Safety lock / System lock
- 41 Stop and Go
- 42 Safety switch-off
- 43 Overheat protection
- 44 Cleaning and care
- 46 Programming
- 50 Troubleshooting
- 54 Optional accessories
- 58 |ctivity and Miele|home
- 58 Registering the cooktop
- 59 To deregister the cooktop
- 60 Safety instructions for installation
- 66 Installation dimensions
- 68 Installation
- 69 Electrical connection
- 70 Technical Service, Data plate