- Industrial & lab equipment
- Electrical equipment & supplies
- Power conditioning
- Power supply units
- MGE UPS Systems
- Pulsar Evolution 1500 Rack
- Installation And User Manual
Connecting the protected equipment. MGE UPS Systems Pulsar Evolution 1500 Rack, Pulsar Evolution 800 Rack, 1500, PULSAR ELLIPSE 800, Pulsar Evolution 1100 Rack, Pulsar Evolution 500 Rack, PULSAR ELLIPSE 500, Pulsar Evolution 1100, Pulsar Evolution 1500, Pulsar Evolution 800
Add to My manuals
65 Pages
advertisement
2. Installation
2.3 Connecting the protected equipment
A Pulsar Evolution 1500 tower UPS has been used below to illustrate the instructions. The principle is the same for all the other tower and rack models.
Check that the indications on the rating plate on the back of the UPS correspond to your AC-power system and to the actual electrical consumption of all the equipment to be connected to the UPS.
2
1
8
6
5
20
1 - Remove the power cord supplying the equipment to be protected.
2 - Connect the power cord (1) just removed from the equipment to the AC-power socket
␣ ␣ 8 , and then to the AC-power wall outlet.
3 - Connect the protected equipment to the
UPS using the two cords 20 .
Connect priority loads to the two standard outlets ␣ 5 and any non-priority loads to the two programmable outlets ␣ ␣ 6 (1 and 2).
If the UPS is connected to a computer running MGE communications software, it is possible to program the interruption of power to the programmable outlets 6 during operation on battery power, thus reserving backup power for the priority loads.
4 - Lock the connections using the securing system 26 (for rack models only).
As soon as the UPS is energised, the battery begins charging. Eight hours are required to charge to the full rated backup time.
(1) Make sure the cord has the following characteristics: 250 V, 10 A, cross-sectional area
1␣ mm 2 , type HO5.
34007117EN/AB
- Page 15
2. Installation
A Pulsar Evolution 1500 tower UPS has been used below to illustrate the instructions. The principle is the same for all the other tower and rack models.
2.4 Connection to the RS232 or USB communications port (optional)
21 The RS232 and USB communications ports cannot operate simultaneously.
2
1
RS232
22
1 - Connect the RS232 21 or USB 22 communications cable to the serial port or the USB port on the computer.
2 - Connect the other end of the communications cable 21 or 22 to the
RS232 2 or USB 1 communications port on the UPS.
The UPS can now communicate with all
MGE UPS SYSTEMS supervision, set-up or safety software.
2.5 Connection to the data-line protection port (optional)
The data-line protection function on the UPS eliminates overvoltages flowing on the computer-network lines.
Simply connect the line to be protected to the UPS using the data-line protection connectors (IN and OUT) as indicated opposite (RJ45 cables not supplied).
RS232
IN OUT
DATA LINE
PROTECTION
Page 16 -
34007117EN/AB
advertisement
Related manuals
advertisement
Table of contents
- 8 Overall view
- 8 Tower models
- 8 Rack models
- 10 Control panel
- 11 Unpacking and parts check
- 11 Tower models
- 12 Rack models
- 13 Installation
- 13 Tower models
- 14 800/1100/1500 Rack models
- 15 500 Rack model
- 16 Connecting the protected equipment
- 18 Installation of the communications-card option
- 19 Start-up
- 20 Transfer to battery power
- 20 Threshold for the low-battery warning
- 21 Function
- 21 ON / OFF conditions tab
- 21 Battery tab
- 22 Voltage-thresholds tab
- 22 Sensitivity tab
- 40 Gesamtansicht
- 40 Tower- Modell
- 40 Rack- Modell
- 41 Rückansicht
- 42 Anzeige- und Bedienfeld
- 43 Entfernen der Verpackung und Überprüfung des Lieferumfangs
- 43 Tower- Modell
- 44 Rack- Modell
- 45 Aufstellung
- 45 Tower- Modell
- 46 Rack- Modell
- 48 Anschluß der Verbraucher
- 51 Inbetriebnahme
- 52 Umschaltung auf Batteriebetrieb
- 52 Voralarm "Ende der Autonomiezeit
- 53 Software, Installation und Funktion
- 53 Registerkarte "Ein/Aus-Bedingungen
- 53 Registerkarte "Batterie
- 54 Registerkarte "Spannungsgrenzwerte
- 54 Registerkarte "Ansprechempfindlichkeit