- Home
- Domestic appliances
- Large home appliances
- Washer dryers
- Whirlpool
- 3389591
- Installation instructions
recessed and closet installation. Whirlpool 3389591
Add to My manuals9 Pages
Whirlpool 3389591 is a large capacity, thin twin washer and dryer with a variety of features to make laundry day easier. It has a four-wire, 240-volt electrical connection and requires a grounded electrical outlet. The washer has a variety of cycles to choose from, including a quick wash cycle and a delicate cycle. The dryer has multiple heat settings and a wrinkle-prevent option. Both the washer and dryer have a large capacity, so you can wash and dry more clothes at once.
advertisement
Recessed and closet installation instructions
Recessed area minimum installation spacing
Fire Hazard l
It is recommended that the dryer be exhausted outside l
If washer/dryer is installed in a closet, the dryer MUST be exhausted outside.
Failure to do so may cause a fire.
This washer/dryer may be installed in a recessed area or closet.
The installation spacing is in inches and is minimum allowable. Additional spacing should be considered for ease of installation, servicing and compliance with local codes and ordinances.
If closet door is installed, the minimum unobstructed air openings in top and bottom are required. Louvered doors with equivalent air openings are acceptable. Closet installation must be exhausted.
Other installations must use the minimum dimensions indicated.
TO PREVENT LARGE AMOUNTS OF LINT
AND MOISTURE FROM ACCUMULATING,
TO MAINTAIN DRYING EFFICIENCY, THIS
APPLIANCE SHOULD BE EXHAUSTED
OUTDOORS. a- 3”
Washer
I
•I .
Side View Front View
Recessed, non-exhausted installation must use only the rear exhaust position and Exhaust Deflector Part No. 694609.
Note: If recessed installation is exhausted to the side or rear, 6 inches must be available above the washer/dryer but all other spacing can be 0 inches.
J
Closet installation must be exhausted outdoors.
/
Closet Door
4
6” f
48. sq. in. +*
4
1” min.+
24. sq. in. l
*
Side View
Closet Door sq. in. l
*
Product dimensions
1+26-l/4’ +I
+27-3/a” -
-i sq. in. l
*
4
Front View
* Additional clearances for wall, door and floor moldings may be required or if external exhaust elbow is used.
** Opening is minimum for closet door, Louvered door with equivalent air openings is acceptable.
*** $MiEnal space may be needed for exhaust
Panel G
advertisement
Related manuals
advertisement
Table of contents
- 1 front cover
- 2 before you start
- 2 tools and materials needed
- 2 electrical requirements
- 3 exhaust requirements
- 4 installation steps
- 4 step 1-unpack parts
- 4 step 2-make sure all parts are included
- 4 step 3-remove shipping strap
- 4 step 4-insert flat washers
- 4 step 5-prepare inlet hoses
- 4 step 6-prepare drain hose
- 4 step 7-clamp drain hose
- 4 step 8-move product close to final position
- 4 step 9-check length of drain hose
- 5 step 10-flush faucets
- 5 step 11-install inlet hoses
- 5 step 12-adjust rear lgs
- 5 step 13-level product
- 5 step 14-tighten legs
- 5 step 15-cut shipping straps
- 5 step 16-remove access panel
- 5 step 17-venting
- 5 step 18-seal all joints ine exhaust duct
- 5 step 19-check electrical requirements
- 5 step 20-make sure all parts have been installed
- 5 step 21-make sure you removed all shipping pieces
- 5 step 22-make sure you have all your tools
- 5 step 23-check faucets for leaks
- 5 step 24-replace access panel
- 5 step 25-read owners manual-check lint screen
- 5 step 26-allow washer to complete regular cycle
- 5 step 27-allow dryer to complete full heat cycle
- 6 alternate electrical connection
- 6 local codes
- 6 to convert to a 3-wire electrical system
- 7 to remove power supply cord
- 7 direct wiring connection
- 8 recessed and closet installation
- 8 product dimensions
- 9 if washer/dryer does not operate properly
- 9 when moving washer/dryer
- 9 assistance/service