- Home
- Domestic appliances
- Large home appliances
- Washer dryers
- Whirlpool
- 3389591
- Installation instructions
if washer/dryer does not operate properly. Whirlpool 3389591
Add to My manuals9 Pages
Whirlpool 3389591 is a large capacity, thin twin washer and dryer with a variety of features to make laundry day easier. It has a four-wire, 240-volt electrical connection and requires a grounded electrical outlet. The washer has a variety of cycles to choose from, including a quick wash cycle and a delicate cycle. The dryer has multiple heat settings and a wrinkle-prevent option. Both the washer and dryer have a large capacity, so you can wash and dry more clothes at once.
advertisement
![if washer/dryer does not operate properly. Whirlpool 3389591 | Manualzz if washer/dryer does not operate properly. Whirlpool 3389591 | Manualzz](http://s1.manualzz.com/store/data/001451664_1-b7c94a418b3b82cae489d2582d63ec9a-360x466.png)
If washer/dryer does not operate properly.. .
Check the following to be sure that:
1, Electric supply is connected.
2. House fuse or circuit breaker is intact and tight.
3. Washer lid or dryer door is closed.
4. Controls are set in a running or “ON” position.
5. Dryer start button has been firmly pushed.
6. Make sure shipping strap has been completely removed and was used to secure the drain hose to the tub or standpipe. l l l
When moving the washer/dryer.. .
Disconnect the power supply cord, then tape securely to the washer/dryer.
Tape the drum to the front panel.
Tape the lint screen in place. Tape the dryer door closed.
Wedge a blanket between the tub ring and cabinet top to restrict tub movement.
If you need assistance...
The Whirlpool Consumer Assistance
Center will answer any questions about operating or maintaining your washer/dryer not covered in the
Installation Instructions. The Whirlpool
Consumer Assistance Center is open 24 hours a day, 7 days a week. Just dial
1-800-253-l 30 1 - the call is free.
When you call, you will need the washer/dryer model number and serial number. Both numbers can be found on the serial/rating plate located in the door well behind the dryer door and on front of opening.
If you need service...
In the event that your Whirlpool appliance should need service, call the dealer from whom you purchased the appliance or a Whirlpool-authorized service company. A Whirlpool- authorized service company is listed in the Yellow Pages of your telephone directory under “Appliances -
Household - Major - Service or
Repair.” You can also obtain the service company’s name and telephone number by dialing, free, within the continental United States, the Whirlpool
Consumer Assistance Center telephone number, 1-800-253-l 301. A special operator will tell you the name and number of your nearest Whirlpool- authorized service company.
Maintain the quality built into your
Whirlpool appliance - call a Whirlpool- authorized service company.
Part No. 3389591
01992 Whirlpool Corporation Prepared by Whirlpool Corporation, Benton Harbor, Michigan 49022
Printed in U.S.A.
advertisement
Related manuals
advertisement
Table of contents
- 1 front cover
- 2 before you start
- 2 tools and materials needed
- 2 electrical requirements
- 3 exhaust requirements
- 4 installation steps
- 4 step 1-unpack parts
- 4 step 2-make sure all parts are included
- 4 step 3-remove shipping strap
- 4 step 4-insert flat washers
- 4 step 5-prepare inlet hoses
- 4 step 6-prepare drain hose
- 4 step 7-clamp drain hose
- 4 step 8-move product close to final position
- 4 step 9-check length of drain hose
- 5 step 10-flush faucets
- 5 step 11-install inlet hoses
- 5 step 12-adjust rear lgs
- 5 step 13-level product
- 5 step 14-tighten legs
- 5 step 15-cut shipping straps
- 5 step 16-remove access panel
- 5 step 17-venting
- 5 step 18-seal all joints ine exhaust duct
- 5 step 19-check electrical requirements
- 5 step 20-make sure all parts have been installed
- 5 step 21-make sure you removed all shipping pieces
- 5 step 22-make sure you have all your tools
- 5 step 23-check faucets for leaks
- 5 step 24-replace access panel
- 5 step 25-read owners manual-check lint screen
- 5 step 26-allow washer to complete regular cycle
- 5 step 27-allow dryer to complete full heat cycle
- 6 alternate electrical connection
- 6 local codes
- 6 to convert to a 3-wire electrical system
- 7 to remove power supply cord
- 7 direct wiring connection
- 8 recessed and closet installation
- 8 product dimensions
- 9 if washer/dryer does not operate properly
- 9 when moving washer/dryer
- 9 assistance/service