- Industrial & lab equipment
- Electrical equipment & supplies
- Power conditioning
- Power supply units
- Allied Telesis
- AT-X900-24XS
- User manual
Management Ports. Allied Telesis AT-X900-24XS, AT-FAN03, AT x900-48FS, AT-9924Ts, AT-8948
Add to My manuals65 Pages
advertisement
Hardware Reference 19
Management Ports
■
■
The following management ports let you configure, monitor, and upgrade the switch:
Out-of-Band Ethernet Management Port
5
6
3
4
7
8
Pin
1
2
RS-232 Terminal Port
The RS-232 ASYN0/CONSOLE port is standard for the x900 series switches and SwitchBlade x908, and connects them to a management device for initial configuration. This port allows the software on the switch to be accessed from a terminal or a PC running terminal emulation software.
The ASYN0/CONSOLE port has an RJ-45 socket with an industry recognised pinout. This requires using a straight-through RJ-45 cable with an RJ-45 DB9 connector when the switch is connected to a terminal or PC. The socket is wired as a DTE and the pin layout is shown in the following table. Pins a re numbered from right to left
Role
RTS
DTR (DSR and DTR are connected but have no other internal connection)
TXD
GND
GND
RXD
DSR (DTR and DSR are connected but have no other internal connection)
CTS
Out-of-Band Ethernet Management Port
■
■
The out-of-band 10/100/1000 Mbps Ethernet port (Eth0) is dedicated to management traffic on the following switches:
■ AT-9924Ts
■ x900-12XT/S x900-24X series
SwitchBlade x908
Use the management port for initial configuration and on-going management tasks. For remote access, use the default IP address, 192.168.242.242. This port is reserved for management only; the switch does not transmit frames between this port and switch ports.
On the SwitchBlade x908, the management port can also be used to create a stack resiliency link when the switch is part of a virtual chassis stack. For more information about resiliency links, see the Stacking Introduction chapter of the
AlliedWare Plus™ Operating System Software Reference.
C613-03092-00 REV J
advertisement
Key Features
- Managed L3+ Web-based management
- Quality of Service (QoS) support
- Basic switching RJ-45 Ethernet ports quantity: 24
- 1U
Related manuals
advertisement
Table of contents
- 6 Devices Covered by this Document
- 7 48-Port Fast Ethernet Switches
- 7 Dimensions
- 7 Mounting system
- 7 Asynchronous serial port
- 7 Environmental conditions
- 7 Regulatory standards
- 7 Switching core
- 8 Processing core
- 8 IPv6 accelerator card
- 8 AT-8948 and x900-48FE switches
- 8 x900-48FS switch
- 9 Gigabit Switches
- 9 Dimensions
- 9 Mounting system
- 9 Asynchronous serial port
- 9 Environmental conditions
- 9 Regulatory standards
- 9 Switching core
- 9 Processing core
- 10 AT-9924T switch
- 10 AT-9924SP switch
- 11 Expandable Gigabit Switches
- 11 Dimensions
- 11 Mounting system
- 12 Asynchronous serial port
- 12 Environmental conditions
- 12 Regulatory standards
- 12 Switching core
- 12 Processing core
- 13 AT-9924Ts switch
- 13 x900-12XT/S switch
- 14 x900-24XT switch
- 14 x900-24XS switch
- 15 SwitchBlade x
- 16 Switch LEDs
- 16 Fast Ethernet RJ-45 port LEDs
- 16 Gigabit RJ-45 port LEDs
- 16 XFP port LEDs
- 17 SFP port LEDs
- 18 System LEDs
- 19 Stacking LEDs
- 20 Management Ports
- 20 RS-232 Terminal Port
- 20 Out-of-Band Ethernet Management Port
- 21 Network Ports
- 21 SFP Ports
- 24 XFP Ports
- 24 RJ-45 Ports
- 24 Stacking Ports
- 25 Expansion Options
- 26 Memory Options
- 26 CompactFlash Card
- 28 Secure Digital (SD) Card
- 30 Dual In-line Memory Module (DIMM)
- 31 Cables
- 31 RS-232 Terminal and Modem Cables
- 32 Cables for RJ-45 Ethernet LAN Interfaces
- 33 Cables for Stacking
- 34 Cable Guidelines
- 35 Troubleshooting Cables
- 35 Cable test
- 35 Cable lengths
- 36 Power Supply Units (PSUs) and Fans
- 37 PWR01 AC and DC PSUs
- 38 PWR02 AC PSU
- 38 PWR05 AC and DC PSUs
- 39 x900-12XT/S fixed AC PSU
- 39 IPv6 Accelerator Card
- 39 How the card works
- 41 Verifying installation
- 42 Displaying information about the card
- 43 Using AT-TFTP Server
- 45 Using Windows Terminal and HyperTerminal
- 49 How the Switch Starts Up
- 49 AlliedWare Plus Operating System Startup
- 49 and x900-24XS Switches
- 55 x900-48FS, and AT-9900 Switches
- 58 Test Facility
- 58 Testing Ethernet LAN Ports
- 59 Diagnostics
- 59 Enabling diagnostics mode
- 60 Running a diagnostic program
- 61 Troubleshooting
- 61 What to check first
- 61 L/A LED on a port is off
- 62 Power LED is off
- 62 Fault LED is on
- 62 Additional resources
- 63 Obtaining Documentation and Resources
- 63 Other resources
- 63 CD-ROM
- 64 Contacting us