- Computers & electronics
- Computer components
- System components
- Internal hard drives
- Seagate
- ST173404FC
- Product Manual
advertisement
Cheetah 73FC Product Manual, Rev. C 3
2.0
Applicable standards and reference documentation
The drive has been developed as a system peripheral to the highest standards of design and construction. The drive depends upon its host equipment to provide adequate power and environment in order to achieve optimum performance and compliance with applicable industry and governmental regulations. Special attention must be given in the areas of safety, power distribution, shielding, audible noise control, and temperature regulation. In particular, the drive must be securely mounted in order to guarantee the specified performance char-
acteristics. Mounting by bottom holes must meet the requirements of Section 8.5.
2.1
Standards
The Cheetah 73FC family complies with Seagate standards as noted in the appropriate sections of this manual and the Seagate Fibre Channel Interface Manual, part number 77767496.
The Cheetah 73FC disc drive is a UL recognized component per UL1950, CSA certified to CAN/CSA C22.2
No. 950-95, and VDE certified to VDE 0805 and EN60950.
2.1.1
Electromagnetic compatibility
The drive, as delivered, is designed for system integration and installation into a suitable enclosure prior to use.
As such the drive is supplied as a subassembly and is not subject to Subpart B of Part 15 of the FCC Rules and Regulations nor the Radio Interference Regulations of the Canadian Department of Communications.
The design characteristics of the drive serve to minimize radiation when installed in an enclosure that provides reasonable shielding. As such, the drive is capable of meeting the Class B limits of the FCC Rules and Regulations of the Canadian Department of Communications when properly packaged. However, it is the user’s responsibility to assure that the drive meets the appropriate EMI requirements in their system. Shielded I/O cables may be required if the enclosure does not provide adequate shielding. If the I/O cables are external to the enclosure, shielded cables should be used, with the shields grounded to the enclosure and to the host controller.
2.1.1.1
Electromagnetic susceptibility
As a component assembly, the drive is not required to meet any susceptibility performance requirements. It is the responsibility of those integrating the drive within their systems to perform those tests required and design their system to ensure that equipment operating in the same system as the drive or external to the system
Electromagnetic compliance
Seagate uses an independent laboratory to confirm compliance with the directives/standards for CE Marking and C-Tick Marking. The drive was tested in a representative system for typical applications. The selected system represents the most popular characteristics for test platforms. The system configurations include:
• Typical current use microprocessor
• 3.5-inch floppy disc drive
• Keyboard
• Monitor/display
• Printer
• External modem
• Mouse
Although the test system with this Seagate model complies with the directives/standards, we cannot guarantee that all systems will comply. The computer manufacturer or system integrator shall confirm EMC compliance and provide the appropriate marking for their product.
Electromagnetic compliance for the European Union
If this model has the CE Marking it complies with the European Union requirements of the Electromagnetic
Compatibility Directive 89/336/EEC of 03 May 1989 as amended by Directive 92/31/EEC of 28 April 1992 and
Directive 93/68/EEC of 22 July 1993.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 11 Scope
- 13 Applicable standards and reference documentation
- 13 Standards
- 13 Electromagnetic compatibility
- 14 Reference documents
- 15 General description
- 16 Standard features
- 16 Media description
- 16 Performance
- 17 Reliability
- 17 Unformatted and formatted capacities
- 17 Programmable drive capacity
- 17 Factory-installed accessories
- 17 Factory-installed options
- 17 User-installed accessories
- 19 Performance characteristics
- 19 Internal drive characteristics
- 19 Seek performance characteristics
- 19 Access time
- 19 512-byte sectors
- 20 General performance characteristics
- 20 Start/stop time
- 20 Prefetch/multi-segmented cache control
- 21 Cache operation
- 21 Caching write data
- 22 Prefetch operation
- 23 Reliability specifications
- 23 Error rates
- 23 Environmental interference
- 23 Interface errors
- 23 Write errors
- 24 Seek errors
- 24 Reliability and service
- 24 Mean time between failure (MTBF)
- 24 Field failure rate vs time
- 25 Preventive maintenance
- 25 Service life
- 25 Service philosophy
- 25 Service tools
- 25 Hot plugging the drive
- 25 S.M.A.R.T
- 27 Drive Self Test (DST)
- 28 Product warranty
- 31 Physical/electrical specifications
- 31 AC power requirements
- 31 DC power requirements
- 32 Conducted noise immunity
- 32 Power sequencing
- 32 Current profiles
- 34 Power dissipation
- 34 Environmental limits
- 34 Temperature
- 36 Relative humidity
- 36 Effective altitude (sea level)
- 36 Shock and vibration
- 38 Air cleanliness
- 38 Acoustics
- 38 Electromagnetic susceptibility
- 39 Mechanical specifications
- 41 Defect and error management
- 41 Drive internal defects/errors
- 41 Drive error recovery procedures
- 42 FC-AL system errors
- 43 Installation
- 43 Drive ID/option selection
- 43 LED connections
- 44 J6 connector requirements
- 44 Drive orientation
- 44 Cooling
- 44 Air flow
- 45 Drive mounting
- 46 Grounding
- 47 Interface requirements
- 47 FC-AL features
- 47 Fibre Channel link service frames
- 47 Fibre Channel task management functions
- 47 Fibre Channel task management responses
- 48 Fibre Channel port login
- 49 Fibre Channel port login accept
- 49 Fibre Channel Process Login
- 49 Fibre Channel Process Login Accept
- 50 Fibre Channel fabric login
- 51 Fibre Channel fabric accept login
- 52 Fibre Channel Arbitrated Loop options
- 52 Dual port support
- 53 SCSI commands supported
- 56 Inquiry data
- 56 Mode Sense data
- 59 Miscellaneous operating features and conditions
- 60 FC-AL physical interface
- 60 Physical characteristics
- 61 Connector requirements
- 62 Electrical description
- 62 Pin descriptions
- 63 FC-AL transmitters and receivers
- 63 Power
- 63 Fault LED Out
- 63 Active LED Out
- 64 Enable port bypass signals
- 64 Motor start controls
- 64 SEL_6 through SEL_0 ID lines
- 65 Device control codes
- 67 Signal characteristics
- 67 TTL input characteristics
- 67 LED driver signals
- 67 Differential PECL output
- 68 Differential PECL input
- 69 Seagate Technology support services