- Computers & electronics
- Computer components
- System components
- Internal hard drives
- Seagate
- ST173404FC
- Product Manual
advertisement
Cheetah 73FC Product Manual, Rev. C 9
4.0
Performance characteristics
This section provides detailed information concerning performance-related characteristics and features of
Cheetah 73FC drives.
4.1
Internal drive characteristics
Drive capacity
Read/write data heads
Bytes per track
Bytes per surface
Tracks per surface
Tracks per inch
Peak bits per inch
Internal data rate
Disc rotation speed
Avg rotational latency
ST173404FC
73.4 .......................... Gbytes (formatted, rounded off value)
24
215-248 .................... KBytes (average, rounded off values)
3,035 ........................ Mbytes (unformatted, rounded off value)
14,100 ...................... Tracks (user accessible)
18,145 ...................... TPI
334 ........................... kBPI
280-427 .................... Mbits/sec (variable with zone)
10,025 ...................... rpm (+ 0.5%)
2.99 .......................... msec
4.2
Seek performance characteristics
4.2.1
Access time
Including controller overhead (without disconnect)
1
,
2
(msec)
Not including controller overhead
(without disconnect)
1,2
(msec)
Average
Single track
Full stroke
Typical
3
,
4
Typical 3,4
Typical 3,4
Read
6.05
0.8
14.2
Write
6.55
1.1
15.2
Read
5.85
0.6
14.0
Write
6.35
0.9
15.0
1.
Execution time measured from receipt of the command to the FCP Response.
2.
Assumes no errors and no sector has been relocated.
3.
Typical access times are measured under nominal conditions of temperature, voltage, and horizontal orientation as measured on a representative sample of drives.
4.
Access time = controller overhead + average seek time.
Access to data = controller overhead + average seek time + latency time.
4.2.2
Format command execution time for
≥
512-byte sectors
Maximum (with verify)
Maximum (without verify)
ST173404FC
240 minutes
120 minutes
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 11 Scope
- 13 Applicable standards and reference documentation
- 13 Standards
- 13 Electromagnetic compatibility
- 14 Reference documents
- 15 General description
- 16 Standard features
- 16 Media description
- 16 Performance
- 17 Reliability
- 17 Unformatted and formatted capacities
- 17 Programmable drive capacity
- 17 Factory-installed accessories
- 17 Factory-installed options
- 17 User-installed accessories
- 19 Performance characteristics
- 19 Internal drive characteristics
- 19 Seek performance characteristics
- 19 Access time
- 19 512-byte sectors
- 20 General performance characteristics
- 20 Start/stop time
- 20 Prefetch/multi-segmented cache control
- 21 Cache operation
- 21 Caching write data
- 22 Prefetch operation
- 23 Reliability specifications
- 23 Error rates
- 23 Environmental interference
- 23 Interface errors
- 23 Write errors
- 24 Seek errors
- 24 Reliability and service
- 24 Mean time between failure (MTBF)
- 24 Field failure rate vs time
- 25 Preventive maintenance
- 25 Service life
- 25 Service philosophy
- 25 Service tools
- 25 Hot plugging the drive
- 25 S.M.A.R.T
- 27 Drive Self Test (DST)
- 28 Product warranty
- 31 Physical/electrical specifications
- 31 AC power requirements
- 31 DC power requirements
- 32 Conducted noise immunity
- 32 Power sequencing
- 32 Current profiles
- 34 Power dissipation
- 34 Environmental limits
- 34 Temperature
- 36 Relative humidity
- 36 Effective altitude (sea level)
- 36 Shock and vibration
- 38 Air cleanliness
- 38 Acoustics
- 38 Electromagnetic susceptibility
- 39 Mechanical specifications
- 41 Defect and error management
- 41 Drive internal defects/errors
- 41 Drive error recovery procedures
- 42 FC-AL system errors
- 43 Installation
- 43 Drive ID/option selection
- 43 LED connections
- 44 J6 connector requirements
- 44 Drive orientation
- 44 Cooling
- 44 Air flow
- 45 Drive mounting
- 46 Grounding
- 47 Interface requirements
- 47 FC-AL features
- 47 Fibre Channel link service frames
- 47 Fibre Channel task management functions
- 47 Fibre Channel task management responses
- 48 Fibre Channel port login
- 49 Fibre Channel port login accept
- 49 Fibre Channel Process Login
- 49 Fibre Channel Process Login Accept
- 50 Fibre Channel fabric login
- 51 Fibre Channel fabric accept login
- 52 Fibre Channel Arbitrated Loop options
- 52 Dual port support
- 53 SCSI commands supported
- 56 Inquiry data
- 56 Mode Sense data
- 59 Miscellaneous operating features and conditions
- 60 FC-AL physical interface
- 60 Physical characteristics
- 61 Connector requirements
- 62 Electrical description
- 62 Pin descriptions
- 63 FC-AL transmitters and receivers
- 63 Power
- 63 Fault LED Out
- 63 Active LED Out
- 64 Enable port bypass signals
- 64 Motor start controls
- 64 SEL_6 through SEL_0 ID lines
- 65 Device control codes
- 67 Signal characteristics
- 67 TTL input characteristics
- 67 LED driver signals
- 67 Differential PECL output
- 68 Differential PECL input
- 69 Seagate Technology support services